Search Documents

By G. B. Pryde, R. M. Magraw

In laying out a new mine, provision should be made for the ultimate recovery of as much coal in any given bed as is consistent with safety and economic mining. Though each mining district, if not each individual mine, has problems that make the adoption of any hard and fast rule impossible, certain basic principles are adapted to practically all conditions. One of the most vital is the provision for barrier pillars of ample dimensions to protect all haulage and permanent airways during the life of the property. Where conditions permit, room or butt entries should be driven on the strike or slightly to the rise, and rooms turned at right angles to these entries. The width of rooms and room pillars is governed by conditions prevailing in the mines under consideration. A safe rule is: In advancing, extract not more than 25 to 35 per cent. of the entire seam; in exceptionally thick seams, considerably less than 25 per cent. should be taken. Rooms usually vary in length from 250 to 350 ft. (76 to 106 m.) with a barrier pillar of not less than 80 ft. between the last crosscut. in rooms and the back entry of the level above. All entries, rooms, and entry-and-room crosscuts should be driven .on sights and room crosscuts should be driven at, right angles to the direction of the rooms. In mines under excessively heavy cover or where roof conditions are bad, rooms should be driven narrow and a barrier pillar left at every fifth to tenth room. This barrier should be of such dimensions that one or more rooms, with pillars of usual dimensions, may be turned through it when the barrier is no longer required. Two of the advantages of such a barrier are the protection of the panel against peaking of roof load during pillar extraction and the easy closing of the entry in case of fire. Where economic conditions permit, it is preferable to follow the retreating panel system of mining. In the case of coal that outcrops, and even in cases where no outcrop is exposed, it is preferable to commence pillar extracting on the high side of the mine. Where the retreating

Jan 1, 1922

THE Institute assembled on Tuesday evening, October 24th, in the hall of the Franklin Institute, Mr. Frank Firmstone, VicePresident, in the chair. Mr. J. Price Wetherill, of Tremont, Pa., read a paper on An Outline of Anthracite Coal Mining in Schuylkill County, Pa. The paper was discussed by Messrs. Coxe, Rothwell, Heinrich, Harden, and Symons. The second session was held on Thursday evening. Mr. A. L. Holley, Chairman of the International Committee, appointed by the Institute to consider the nomenclature of iron and steel, offered the following report of the committee, signed by all the members: WHEREAS, The recent production of soft, cast, malleable compounds of iron by the Bessemer, the Siemens-Martin, and the crucible steel processes appears to demand a new nomenclature of iron compounds, for the following reasons: 1st. The term "steel," by which these soft products are commercially and professionally designated in England and in the United States, does not completely distinguish them from previously existing "steel which would harden and temper. 2d. A nomenclature recognized in all languages seems desirable, as well for commercial as for scientific purposes, especially as lawsuits, already commenced, depend on the meaning of the term " steel." 3d. Although homogeneity, due to fusion, is usually recognized, and is by this committee recognized as the most definite characteristic of both hard and soft steel, this quality may be equally well expressed in other terms, thus leaving the old term, " steel," to define the malleable compounds of iron, which will harden and temper. Therefore, resolved, That this committee recommends the following nomenclature : 1. That all malleable compounds of iron with its ordinary ingredients, which are aggregated from pasty masses, or from piles, or from any forms of iron not in a fluid state, and which will not sensibly harden and temper, and which generally resemble what is called " wrought iron," shall be called Weld Iron (German, Schweisseisen; French, fer soudé). 2. That such compounds, when they will from any cause harden and temper, and which resemble what is now called puddled steel," shall be called Weld Steel (German, Schweiss stahl; French, acier soudé).

By Carl H. Beal

The most important factors that should be given consideration in the valuation of oil lands are: (1) the amount of oil the property will produce; (2) the amount of money this oil will bring (based upon the future prices of oil); (3) development and production costs; (4) the rate of interest on the investment; (5) the retirement or amortization of invested capital; and (6) the salvage or "scrap" value of the equipment when the property is exhausted. These factors are of varying importance and some of them may not enter all valuation problems, but most of them should be given consideration in any valuation even though only a rough estimate of the value of the property is desired. The value of a property may be changed over night by the completion of important test wells, by the sudden water flooding, or by a change in the price of oil. The best a petroleum engineer can give is the value of the property under the conditions existing at the time the appraisal is made with a fair forecast of future action of the wells and of the price of oil. Our experience in the scientific valuation of oil lands is not broad and there is very little published information on the subject; it, therefore, becomes necessary in studying such problems to form comparisons with the factors involved in the valuation of mines—the closest parallel. One of the reasons for the lack of substantial progress in oil-land valuation methods has been the necessity of making an estimate of the future production of the oil property to be valued. Oil men and accountants have not generally conceded that such estimates could be made with any degree of accuracy. It has been shown, however, in several recent publications that with certain data available reasonably close estimates can be made. The accuracy of an appraisal depends chiefly on the accuracy of the estimates of future production and of the future price of oil. The accuracy of the former is sometimes necessarily based on geological inferences. Geology is not an exact science and geological data in connection with oil production cannot always be mathematically evaluated.

Jan 1, 1921

By E. Gybbon Spilsbury

The introduction of underground machinery in mines, and especially the invention of the rock drill, called attention to the necessity for some motive power to drive them. The use of steam generators underground is as a general thing inadmissible, owing to the difficulties of ventilation and the transportation of fuel, and the great loss of power by condensation in the pipes, when surface generators are used, added to the inconvenience of getting rid of the exhaust steam, has precluded the direct use of steam for this class of machinery. Water as a power has with very few exceptions proved a failure, owing to its weight and incompressibility, and therefore the attention of mining engineers has very naturally turned to the use of compressed air. This agent not only answers all the requirements for power, but has the double advantage of greatly assisting in thoroughly ventilating remote workings, and in cooling the underground atmosphere. It is therefore clear that the successful introduction of underground machinery is dependent on the economical production of good and efficient air-compressing machinery. Although many improvements have of late years been introduced in this class of machines, the most of them are open to serious objections, the chief of which are the very small duty they perform for the power expended, and their great expense, due to the complexity of their construction. This latter fault is the chief reason why the introduction of rock drills and other underground engines is so limited, as comparatively few mines can afford to expend the required capital for the installation of a complete compressing plant. But with the introduction of a cheap and effective compressor, there is no doubt that power drills will become as generally used in mines as the hand drills are now. The great excess of power required in most machines to compress air over that given out again by the use of the air thus compressed (amounting as it does in most cases to sixty per cent.) is well known to all mining engineers. Of course a portion of this loss is due to the friction of the air through the pipes, and will always occur however effective the machine used may be, but the chief cause of the

Jan 1, 1880

THE Institute assembled on Tuesday evening, October 24th, in the hall of the Franklin Institute, Mr. Frank Firmstone, Vice-President, in the chair. Mr.. J. Price Wetherill, of Tremont, Pa., read a paper on An Outline of Anthracite Coal Mining in Schuylkill County, Pa. The paper was discussed by Messrs. Coxe, Rothwell, Heinrich, Harden, and Symons. The second session was held on Thursday evening. Mr. A. L. Holley, Chairman of the International Committee, appointed by the Institute to consider the nomenclature of iron and steel, offered the following report of the committee, signed by all the members: WHEREAS, The recent production of soft, cast, malleable compounds of iron by the Bessemer, the Siemens-Martin, and the crucible steel processes appears to demand a new nomenclature of iron compounds, for the following reasons : 1st. The term "steel," by which these soft products are commercially and professionally designated in England and in the United States, does not completely distinguish them from previously existing "steel" which would harden and temper. 2d. A nomenclature recognized in all languages seems desirable, as well for commercial as for scientific purposes, especially as lawsuits, already commenced, depend on the meaning of the term "steel." 3d. Although homogeneity, due to fusion, is usually recognized, and is by this committee recognized as the most definite characteristic of both bard and soft steel, this quality may be equally well expressed in other terms, thus leaving the old term, "steel," to define the malleable compounds of iron, which will harden and temper. Therefore, resolved, That this committee recommends the following nomenclature : 1. That all malleable compounds of iron with its ordinary ingredients, which are aggregated from pasty masses, or from piles, or from any forms of iron not in a fluid state, and which will not sensibly harden and temper, and which generally resemble what is called " wrought iron," shall be called WELD IRON (German, Sehweisseisen; French, fer soudé) 2. That such compounds, when they will from any cause harden and temper, and which resemble what is now called "puddled steel," shall be called WELD STEEL (German, Schweiss stahl; French, acier soudé).

Jan 1, 1877

Discussion of the paper of DOUGLAS BUNTING, presented at the New York meeting, February, 1915, and printed in Bulletin No. 97, January, 1915, pp. 1 to 21. ARTHUR HOVEY STORRS, Scranton, Pa.-I know something about accidents Nos. 4 and 8. At the Fuller mine there was no disturbance of the surface in connection with either of those accidents, there was no surface settling, nor signs of sand in the mine, and seemingly the water all came from a subterranean basin or water-bearing stratum overlying the Six Foot vein. A similar thing was shown, in an accident not referred to in Mr. Bunting's table, at the Avondale, where we had an inflow of water, as high as 12,000 gal. a minute, for a considerable period. Regarding the second accident (No. 8) at the Fuller mine: after the first inflow of water (No. 4 of the table), the mining was abandoned in the Six Foot vein. A long slope was. driven in an underlying seam, and when this had reached a point about 2,000 ft. southeast of the place where the first inflow of water occurred, and where the bore holes show there was apparently sufficient rock covering for the Six Foot vein, a rock plane was driven up to the upper vein (Six Foot) and one afternoon this exposed the coal. During the following night the inflow of the water occurred. There were absolutely no workings at this point so that no disturbance of the overlying rocks could have occurred. The result of the inflow of water was to fill up the entire lower-vein workings in about two or three clays and caused the abandonment of the mine. After several years, considerable time and money were spent in an effort to hoist the water from the shaft and mine workings, with varying, but in the main rather indifferent, success until, clue to the breaking of one hoisting rope, the engineer pulled the other hoisting tank up through the tower and down on to the engine, making a complete wreck of the whole plant. It was then decided to allow the mine to soak and it is still doing so, other portions of the property being mined from adjoining collieries.

Jan 5, 1915

By A. F. Lucas

EACH day, the fact becomes more evident that the ever-growing demand for oil is farther outstripping production, regardless of the increase in output throughout the past twenty years. The development of known oil fields and the prospecting for new ones along present lines are not resulting, in, and cannot bring forth, supplies large enough adequately to meet the oil needs of the country. The usual methods of prospecting-for new supplies are insufficient to meet the exigencies of the situation which threatens, in the not distant future, to reach a critical stage. Were it not that within the last two years new and prolific oil fields have been discovered in northern Louisiana, central Texas, and California, this crisis would undoubtedly be now at our door. Stocks are being exhausted in spite of the rapid growth of imports. The time is therefore fast approaching when some radical departures must be made in the method of prospecting and developing old and new fields in order to increase our oil supplies. Methods and chances, that have seemed unwarranted will not only be given serious consideration, but, according to the results promised, will be put to the test. Meanwhile, however, nearly all the oil fields are responding to the stimulus of higher prices, whereby enormously growing capital is attracted to this important industry, both here and abroad; the increase in our petroleum production at the present time is due to this circumstance. Yet, although a most active search is being made for possible sources of additional supply, one section of our country is not yielding the results that, in my opinion, it is capable of producing: I allude to the coastal dome belt of Texas, Louisiana, and Mexico. The United States Geological Survey has estimated that three-fourths of a billion barrels are available in the ground in the Coastal Plain of the two states just mentioned. Numerous papers have been written on the subject of the salt domes of the Coastal Plain and more or less attractive theories have been advocated by leading geologists to account for their origin and the presence of the oil, sulfur, and salt associated in them. However, owing in part to the generally monotonously level country in which the coastal

Jan 9, 1920

By Eric Sinkinson

MANY of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally enclosed in-serpen-tine masses, somewhat decomposed, and in mining it wall rock is inci-dentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumna, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18° C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact; MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18° C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H20) or (4MgCO3.Mg(OH)25H20), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2. The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates. The range in published figures for solubility

Jan 1, 1936

By John Freeman

THE die pressing of brass may be described as a method of producing irregularly shaped parts of brass and other copper alloys by hot deformation in a die under pressure. Die pressing of brass was first developed as an improvement on sand castings in order to obtain irregularly shaped articles of brass with superior surfaces, a closer tolerance in dimensions, a denser structure, freedom from porosity and elimination of the relatively large amount of scrap invariably attached to sand castings. The freedom from sandy surfaces with consequent greater tool life in machining operations was also recognized as well as elimination of losses due to the uncovering of blowholes in machining operations. Die pressing also gave alloys of superior strength. Die pressings today are made from extruded rod or shapes, according to design of the part to be made. The greater number of pressings are made from round rod, because of its relatively lower cost and ease of handling. The rod is first sheared or sawed into desired lengths, the diameter of rod used and length of "slug" or "rivet" depending upon ultimate weight and shape of the die-pressed part to be made and design of die. The dimensions of the slug are figured so as to give the, minimum amount of scrap to be sheared from the pressing as it comes from the-die. Extruded shapes having I, T or X sections are often used when the finished part is to have a similar shape or heavy sections are joined by relatively light sections of considerable length. A rod bent in the shape of a U is also used on occasion, for similar reasons. Proper shearing of the slugs is of considerable importance. The sheared ends of the slugs should be as flat and straight as possible. Improperly sheared ends having an angle to the axis of the bar or a rough, uneven surface are liable to give folds or laps in the finished pressing and proportionately high rejections. The property of shearing varies considerably with different alloys and should be considered in the selection of a material for a given part. Where satisfactory shearing is not possible, the slugs may be cut from the bar by power saws. Extruded

Jan 1, 1931

By J. R. Thoenen

IF ASKED whether limestone production was a mining problem I would; not hesitate to answer emphatically in the affirmative. The question, "When is a quarry a mine?" is familiar. The immediate mental picture induced by the thought of limestone production is that of an open quarry. All are familiar with the open pit in the iron-producing districts of Minnesota and Michigan and the open cuts of the so-called "porphyry" coppers of the West. If these are mines, they differ little from limestone quarries in general mode of operation; if quarries, why do they need the attention of mining engineers? During 1923, the United States produced in round numbers 70,000,000, tons of ore. The limestone production of the United States for the same period was something over 100,000,000 tons. In tons, it about equals the oil production of the United States. The uses of limestone are legion. A paper read by a prominent engineer of Chicago, at the meeting of the National. Crushed Stone Association held last February in St. Louis says: "There is no industry in the United States today that is more basic in its operation or by itself controls. more industries. There is hardly a chemical operation, hardly a metallurgical operation or building operation that a crushed-stone man does not control if he will jump in and make the full utilization of it." Some of the many uses are for road metal, concrete, railway ballast, building stone, riprap, and rubble, the manufacture of iron and steel, alkalies, calcium carbide, magnesia, carbolic and carbonic acids, asphalt filler, mineral wool, poultry grit, sulfuric acid, phosphates, nitrates, soap, baking powder, the purification of copper and prevention of coal-mine explosions, to say nothing of the quantities used in the making of lime and cement. It has been said that without iron we would revert to the Stone Age; how much iron would we have without limestone? From the point. of view of the mining engineer, using the term in its broad sense to include geologists and metallurgists, the production of limestone is important because of its occurrence, volume, commercial importance, and the problems presented by its recovery and treatment.

Jan 2, 1925

By Sidney Wise

WHILE the installation of mine bulkheads to retain water under high pressure is y no means a rarity, the following points Which arose in the designing and placing of two of these bulkheads may be of interest: The Hibernia magnetite mine, located about 40 miles west of New York, in the State-of New Jersey, is partly filled with water. This mine is located on an ore lens, the outcrop of which is over a mile long. The ore has been mined from this lens from the surface to a depth of more than 1,500 ft. It was held desirable to- separate the old workings from the new, and to allow the former to fill to the 850-ft. level. Two weak places existed between the new and old workings below this level: namely, a temporary bulkhead on the 10th level and a rock bulkhead of indeterminate thickness on the 16th level. When the matter of allowing the old workings to fill was investigated, the fact was developed that if these old workings were filled, the bulkhead on the 10th level would be subjected to a water pressure of about 50 lb. per square inch, and that 200 lb. per square inch would act on the 16th-level bulkhead. As the above-mentioned barriers were not deemed of sufficient strength to permit of these pressures, it became necessary to design and install new bulkheads. Design As the 16th-level bulkhead was required to withstand a pressure of 200 lb. per square inch, it presented some difficulties. A careful consideration of the various types of mine dams now in use led to the adoption of a design of the form of a truncated wedge. In this, the pressure side of the dam is of greater area than the back, so that the resultant action is similar to driving the wedge. By cutting generous skewbacks in the walls, roof, and floor, this type in reality becomes an invisible arch. The wedge feature tends to compress the materials in the bulkhead, thereby adding to its imperviousness.

Jan 8, 1914

By Oscar M. Kucus

In January and February of the current year, at the Tooele plant of the hternational Smelting Co., Tooele, Utah, a modification of the usual method of converting, for the treatment of copper-lead matte from lead blast furnaces, was developed and put into successful operation. In brief, the method consists in blowing molten matte direct from the blast furnaces in basic-lined converters, without the addition of siliceous fluxing ores, to the almost complete elimination of the lead contained, and to the production of copper bullion, the resulting lead fume being recovered by the filtration of the converter gases through woolen fume bags. The process is carried out in conjunction with the converting of rever-beratory copper matte, the heavy iron slag, together with the copper precipitated, being transferred to converters blowing copper matte. The purpose of this transfer is to reduce the copper oxide formed, due to the necessary overblowing of the lead-matte charge, and to utilize, as far as possible, the value of iron from the lead matte, for the fluxing of siliceous dry ores. The final slag from the copper converters is then skimmed off and transferred molten to a reverberatory smelting furnace treating copper ores. This variation from general converting practice was the outgrowth of results obtained during 1913 when it was endeavored to convert copper-lead matte in the usual manner, with the direct addition of siliceous fluxing ores. To make clear the reasons lying back of the process it is necessary to recount at some length the results of operations during that year. In the design of the lead plant it mas planned to treat the copper-lead matte from the furnaces by direct converting without reconcentration and thereby to recover the copper, silver, and gold as quickly as possible. A converter plant of ample capacity, treating copper matte, already being in operation, it was only necessary to install a bag house, a fan, and the necessary flues to complete the equipment. The bag house constructed has a bag-cloth filtering area of 136,000 sq. ft., provided by 960 fume bags, 18 in. in diameter by 30 ft. in length. A No. 20 Sirocco fan of 180,000 cu. ft. capacity delivers the gases from

Jan 1, 1915

By S. D. Michaelson, Eric Sinkinson

Many of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally enclosed in serpentine masses, somewhat decomposed, and in mining it wall rock is incidentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumina, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18" C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact, MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18" C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H2O) or (4MgCO3.Mg(OH)25H2O), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2. The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates. The range in published figures for solubility

Jan 1, 1938

By J. J. Forbes

THE Federal Coal Mine Safety Act (Public Law 552, 82nd Congress) was approved on July 16, 1952. It incorporates, as Title I, the Coal Mine Inspection and Investigation Act of May 7, 1941 (Public Law 49, 77th Congress), which gave Federal inspectors only the right to enter coal mines for inspection and investigation purposes but no power to require compliance with their recommendations. Title II contains the enforcement provisions of the act; its purpose is to prevent major disasters in coal mines from explosions, fires, inundations, and man-trip or man-hoist accidents. At this point a brief account of events that pre- ceded the enactment of the Federal Coal Mine Safety Act seems appropriate. The hazardous nature of coal mining was recognized by the Federal Government as long ago as 1865, when a bill to create a Federal Mining Bureau was introduced in Congress. Little was done, however, until a series of appalling coal- mine disasters during the first decade of this century provoked a demand for Federal action. As a result an act of Congress established a Bureau of Mines in the Department of the Interior on July 1, 1910. The act made it clear that one of the foremost activities of the Bureau should be to improve health and safety in the mineral industries. One of the first projects selected by the small force of engineers and technicians then employed was to determine the causes of coal-mine explosions and the means to prevent them. By investigations after mine disasters the fundamental causes and means of prevention were soon discovered, and the coal mining industry was informed accordingly. However, despite this knowledge and the enactment of State laws and the Federal Coal Mine Inspection and Investigation Act of 1941, mine disasters continued to occur with disheartening frequency and staggering loss of life. The devastating explosion at the Orient No. 2 mine on December 21, 1951, resulted in the death of 119 men. The Orient disaster rekindled the memory of the Centralia, I11., disaster of March 25, 1947, which caused the death of 111 coal miners. These two tragedies ultimately brought about enactment of the Federal Coal Mine Safety Act.

Jan 1, 1954

By J. Parke Channing

WE are accustomed to think that we are efficient in the United States, particularly with respect to such things as mining and manufacturing. The conduct of the war has demanded in England and in France a complete readjustment of manufacturing methods and plans, and today England is probably as efficient a country as there is in the world, not even excepting Germany. This is all the more remarkable because it has been notorious for years that England has been inefficient in her manufacturing and the country has been flooded with things "Made in Germany." Today England is almost a socialistic community and the State is doing almost everything. England is now in such a position that practically everyone in the country is engaged in industry necessary for the conduct of the war, and this has been accomplished by increasing the efficiency both of her tools and of her man power. In the United States we certainly have been efficient so far as machines and perhaps so far as methods have been concerned, but we have not been efficient iii the utilization of our man power. Before the war, our labor was undoubtedly far more efficient than that of England, but it certainly was not so highly efficient as it should have been, and the problem that confronts us today, and will all the more confront us after the war, is to make our man power efficient. England has had a taste of what you may call State Socialism, and her laboring men are not going to be content to return to the old order of things. There is one feature of the labor problem in England which has permitted her to reach this condition of state socialism with comparative rapidity; this is that practically all of her laborers are English; she has little or no foreign population. While an Englishman may he a strong union man and ready to fight his employer tooth and nail, at heart he is still a British subject, and when his country was in danger he rose to the occasion.

Jan 5, 1918

By B. B. Cox

Iraq, formerly called Mesopotamia in Asiatic Turkey, became a kingdom under British Mandate after the world war and is expected to gain its independence in 1932 when it enters the League of Nations. The kingdom is shown on Fig. 1 in its relations to neighboring countries, to the Mediterranean Sea and to the Persian Gulf. It is slightly smaller than the State of Texas with its capitol, Baghdad, inland about as far from the Persian Gulf as Breckinridge, Tex., is from the Houston Shipping Channel. The oil fields lie 180 to 225 miles north of Baghdad, or about as far as from Breckinridge to Oklahoma City, and about as far from the Mediterranean as Fort Worth is from Hobbs, N. M. A narrow-gage railway runs from Basra, the Persian Gulf port, to Baghdad. From there another narrow-gage runs into the Kurdish hills east of the Tigris to Kirkuk. A standard-gage, part of the old Berlin-Baghdad system, follows the west bank of the Tigris northward from Baghdad to Baiji, a village about 100 miles south of Mosul. No railway exists between Iraq and the Mediterranean, though the Anatolian Railways in southern Turkey come to within 50 miles of the Iraq frontier and 120 miles of Mosul. Surveys have been completed for a railway through British Mandates from Haifa to Baghdad as well as for a railway through French Mandated Syria from Tripoli to Abu Kemal near the Iraq border. Wagon roads, excepting those constructed by the oil companies, are few and indifferent in Iraq and no road exists across the desert to the Mediterranean, but contrary to prevalent beliefs the surface is firm and free from sand dunes so that motor cars can go almost anywhere in dry weather, with ease. Frequent motor car and airplane service exists between Baghdad and the Mediterranean ports and motor car service may be had between Kirkuk and Nisibin, Turkey, where on two days each week through Wagons Lits service is available to Paris. Baghdad is about 21 days distant from New York City with present transport facilities. The climate is semiarid, similar to Imperial Valley, California, the average rainfall outside the mountainous parts amounting generally to

Jan 1, 1932

By W. H. Meyer

Although an aerial photograph is not a map, most of the information that is necessary for compiling a map is recorded in the photograph provided some form of radial-line method is used to determine the true position of images. The slotted- templet method, which is based on the well-established radial-line principle, has made it possible to construct accurate mosaic maps at a cost comparable with that formerly charged for the average mosaic. It makes possible the securing of these results with far less ground control, which is always expensive. It has expanded widely the possible use of aerial photographs for mapping. ALTHOUGH a vertical or oblique aerial photograph is not a map, most of the information that is necessary for compiling a map is recorded in the photograph. Some ground controls or data are needed, the number and accuracy to be governed by the mapping method to be used and the scale and final accuracy desired in the finished map. RADIAL-LINE CONTROL It is essential that the principle of radial-line control in the use of vertical aerial photographs be understood and accepted before any confidence in the slotted-templet method can be gained. A simple sketch and some enlargements showing the Empire State Building will serve to illustrate the cause of displacement of an image that is above the datum plane as recorded in the photograph. The top of the tower of the Empire State Building is directly above the base, and when the image of the top is shown almost two blocks away from the center of the base, it is evident that the image of the top of the tower is not the true location, and in this particular case we know where the true location is; namely, over the center of the base of the tower. If the top of the tower were the top of a hill 1250 ft. high, we would have no way of knowing by inspection the true position of the top of the hill, so it is very important to have a method whereby the true location of any such point can be determined, and thereby make it possible to convert the detail of an aerial photograph into accurate information for mapmaking.

Jan 1, 1939

By H. C. Hardison

The Yates pool, Pccos County, Texas, has greater potential capacities than any other field in the United States. This field is notable for the large return it yields on capital invested, for low production costs and for the orderly and conservative manner in which it was developed and continues to be operated. The proven area is 20,000 acres and there are 392 producing wells, or approximately 1 well to 50 acres. The theoretical daily potential is 5,250,000 bbl. as determined by l-hr. open-flow gages. Individual well gages vary from a few barrels to 8500 bbl. per hour, and well depths range from 1000 to 1800 ft. The greater part of the production is from a very porous limestone, and by agreement no productive well has penetrated the lime more than 225 ft. The forces driving the oil from the formation to the surface are hydrostatic head, expanding gas or a combination of the two. The degree of effectiveness of either depends upon the structural position of, and porosity encountered in, the individual wells. Approximately 95 per cent. of the wells in the field flow naturally. The pipe line outlet of the field at the present time is 100,000 bbl. per day, which is less than 2 per cent. of the daily potential. Difficulties and Principles of Probation It became evident during the first year of the development of this field that operators would have to devise a scheme to allocate pipe line runs equitably among their different properties. When the idea of proration was first inaugerated, the matter of spacing wells was given consideration. This was given up through fear of legal difficulties. Storage was also a question that was given considerable thought, and a plan was finally developed which went into effect Oct. 1, 1927. It was decided that the oil runs should be prorated according to the total potential capacity of all the wells which the several operators had in the field. The potential capacity of the wells was measured by a l-hr. open-flow gage. All runs to storage by an operator were deducted from his daily allowance.

Jan 1, 1931

By Eric Sinkinson

MANY of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining' of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally. enclosed in serpen-tine masses, somewhat decomposed, and in mining it wall rock is inci-dentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumina, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18° C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact, MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18° C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H20) or (4MgCO3.Mg(OH)25H20), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2, The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates.. The range in published figures for solubility

Jan 1, 1936

By J. Morgan Clements

PETROLEUM has been known in Japan since at least 668 A. D., for a picture shows the presentation, during that year, to the Emperor Tenchi (Tenji) of "burning water" and." burning earth" by his subjects from Echigo Province, which today is the largest producer of petroleum in Japan. The burning water was doubtless petroleum and the burning earth either bituminous shale or oil-soaked earth or rock from near the oil seepages. The early methods of getting the oil were simple and similar to methods used today in Japan and in China. Where the seepages occurred, trenches or shallow wells were dug along the seepages and allowed to fill with oil which was then bailed out; in some cases, they filled with oil and water and overflowed. During the 300 years following 1500 A. D:, the use of petroleum in Echigo Province seems to have increased considerably, as compared with earlier centuries, and records show that in 1818 the depth of the wells had been greatly increased. Doubtless, they passed through the seepages and tapped the shallow oil-bearing strata; probably some of these deeper wells were dug before that time. The real value of petroleum was not recognized until early in the Meiji era, which began in 1868, when the Japanese learned that the kerosene that was being imported was derived from petroleum. Guided solely by information obtained from books, they refined the oil and increased the depth of their wells in order to increase the production. The deepest well, dug by hand, about this time was 894 ft.1 (273 m.) and by 1874 the recorded production reached 3499 barrels. In 1876, Benjamin Smith Lyman prepared geological maps of the Echigo oil field, which were the first. of such geological maps made in Japan, and based on these a more enlightened development of the oil fields began; the. Japanese, however, still dug the wells by hand. Toward the end of the '80s, an American well-drilling outfit was secured, but the efforts to use it failed from lack of experience by the operators. In 1888, a complete well-drilling outfit was, purchased and American oil-well

Jan 7, 1922