Search Documents

By N. H. Jensen, B. L. Sackett, Carlos Bardwell, Simon Jacobson

Lead smelting has been an important industry in Utah for many years. The first lead smelting was done, over 60 years ago, at the Rollins mine in Beaver County, by burning heaps consisting of alternate layers of wood and high-grade carbonate ore. The lead thus obtained was molded into bullets. With the development of the mines, the problem of cheaper handling of the ore became important. The only outlet for this ore was Swansea or the Atlantic Coast but to ship to either cost $150 per ton or more for treatment and handling. From 1864 to 1871, experimenting was done with blast, Scotch hearth, and reverberatory furnaces, with the blast furnace surviving as the standard plant. The first crude furnaces were circular or hexagonal in shape, and were made of adobe and stone, which quickly burned out. They were small, about 21/2 ft. in diameter, and smelted from 3 to 10 tons in 24 hr. The metal had to be tapped from the bottom of the crucible, necessitating a shut down of the furnace during this process. This procedure caused salamanders to form around the tap hole when the furnace was started again, which frequently resulted in freezing. The campaign lasted until a tap of bullion was made. The first successful plant of the crude stone type was operated in 1870. From 1870 to 1872, there was a smelter building craze in the state. During that period, about 20 furnaces were built, chiefly near the mines, and their operation was limited and sporadic. The work was then placed in the hands of trained metallurgists, who standardized on the rectangular form of furnace. In 1871, Daggett, at the Winnamuck mine in Bingham, installed water-jackets around the smelting zone of the furnaces. These furnaces were circular; the diameter at the tuyere line was 3 ft. 6 in. and at the charge floor 5 ft. 3 in. The height from tuyere line to charge floor was 14 ft., height of tuyere line above top of crucible was 3 ft. 8 in. Furnace capacity was about 14 tons per day, with a campaign of about 16 days. Cost of smelting was about $44 per ton. The ores making the

Jan 1, 1926

By E. B. Olds, Burt. B. P.

THE mines of the Consolidated Coppermines Corporation are at Kimberly, in the Robinson mining district, White Pine County, Nevada. [ ] The blanket-like ore body is a disseminated copper deposit occurring in monzonite porphyry and, in general, is thoroughly fractured, altered, and soft. Contained in the porphyry ores of the extreme westerly end of the ore body are pendants of hard garnetized limestone. A younger monzonite porphyry underlies the ore-bearing porphyry, which in turn rests on limestone and shale. Block caving is the standard method of mining. Because of the undulating top and bottom contours of the ore body, the main haulage level was selected and driven at an elevation calculated to be the most economic depth below the major tonnage sections of ore. Fig. I shows a general section of the Emma Nevada ore body taken through its long axis, which lies roughly in an east-west direction. Mine openings in either type of porphyry require heavy timbering and constant maintenance and repair, particularly in horizons at or near the ore body contact. Where the ore lies close to the haulage level, slusher hoists and scrapers are used to transport horizontally the ore to the main haulage drift (Fig. 2). For the extraction of high-lying ores, a system of branch raises is used; and the ore is mined by gravity. Slushing methods are used also on the high-lying ore-body fringes. Slusher drifts are often driven from the fringe branch raises that have already served their purpose, in order to minimize the cost of the preparatory work in mining the thinner portions of the ore body (Figs. 3 and 4). When a block of ore is developed and undercut, it is economical to mine it as rapidly as the ore will cave efficiently; and this procedure often presents safety problems because of men with equipment working in a relatively congested area. The single-track main haulage drift is about 1 ½ miles long, and lateral haulage drifts are driven under the ore body at intervals determined by the height of the ore body above the haulage level. In order to minimize repair and maintenance, the

Jan 1, 1946

By W. A. Anderson, R. F. Mehl

RECRYSTALLIZATION of cold-worked metals has long been known to proceed by a process of nucleation and growth.1 When a cold-worked metal is heated to a temperature at which recrystallization will ensue, nuclei of new grains, essentially strain-free, appear and grow. As the process proceeds, nuclei continue to appear and to grow, until the cold-worked matrix has been entirely consumed and recrystallization has been completed (Fig. I). Conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time, yields an isothermal recrystallization curve, showing the time course of the recrystallization process (Fig. 2).2 Evidently, then, the rate of recrystallization is determined by the rate at which nuclei form and the rate at which they grow. The rate of nucleation N is the number of nuclei that form in unit time in unit volume of the unrecrystallized matrix, and the rate of growth G is the increase in radius of the recrystallized grain per unit time. In recent years attempts have been made to determine N and G as these vary with the well-recognized variables affecting recrystallization: time, temperature, degree of deformation, etc.' Such studies yield information that is more fundamental than that conveyed by the conventional recrystallization diagram,' since the rate of recrystallization is thus analyzed into its two component rates.2 Methods are now available by which N and G can be measured, and analytical expressions have been developed for the interrelationships among N, G, the isothermal recrystallization curve, and the final grain size, which greatly facilitate analysis.2-4 The application of these methods has been demonstrated recently for the recrystallization of silicon ferrite.2 Data on N and G in dependence upon the recognized recrystallization variables are, however, very fragmentary;* values of N and G have been determined for some metals, but the effect of temperature, which would yield the fundamentally important activation energies, has been too little studied. Thus far there has been no detailed study of the recrystallization of any one metal in terms of N and G over appreciable ranges of the variables time, temperature, degree of deformation, and original grain size. It is the purpose of the present paper to provide such a study, employing aluminum.

Jan 1, 1945

By Roswell H. Johnson

What becomes of the water which must have filled the oil and gas sands at the time of deposition, has long puzzled students of oil and gas and has found expression in Munn's well-known article on the hydraulic theory. Both Munn and Clapp have pointed out that in the Appalachian field the deeper sands carry increasingly less proportionate amounts of water. It seems to me probable that the principal source of oil and gas has been in the shales in proximity to the sands which now contain these products. The sand spits which mark off the lagoons from the sea comply particularly with the requirements of a limited sand imbedded in shales rich in organic matter. Cunningham Craig has objected to this view that the rich organic muds of lagoons are found only at the surface. That such muds do extend to considerable depth 1 am assured by Prof. Douglas W. Johnson, who has made an extensive study of the Atlantic Coast marshes. As any particular sand body becomes weighted by a heavier and heavier overburden, the result of increasing deposition, a part of the very large percentage of water in the uncompacted sand and mud is forced out. The water percentage of freshly settled mud is vastly higher than that of the resultant shales, or even of a very porous sand. If beds of less compressible material meet or underlie the shales in question, there will frequently be a lateral motion along such beds to some point where the upward movement will be resumed. We find in our laboratory work here that oil, gas, and water have extremely slight capacity for gravitational sorting while in a state of rest, but when moving the gravitational sorting is readily accomplished. As the oil, gas, and water pass a body of larger pores, the gas, owing to its lack of capillary attraction, is retained in the large pores. This has been predicted by Washburne, Blatehley and others on the ground that the water has a higher capillarity and grips the finer pores in such a way that there will be a greater proportion of oil and gas in the large

Jan 1, 1915

By O. R. Bergmann

Two approaches were taken to obtain direct experimental evidence jar the existence oj a jet in the explosion-cladding pvocess: 1) direct observation of the claddirg jwocess by rtzeans ojf kig-h-speed photography using a fvartziiy catnera and 2) use of a plated-surface experiment in contribution with clzetrzical analysis. The framing-camera records showed clearly the presence of a jet it1 the form of what appears to be a line spray. The jet velocity is considerably highev than the detonation velocity arid in vacuum it is almost twice as high as the detonatiou velocily. The results jrorrz the plated-surface experiment also corzfivtned the preseizce of- a jet. The artzoutlt o,f etzergy dissipated in the jetting process was foundd lo be consislent with the basic theovetical model o/ the cladding mechanism.. MaNY reports on metal working with explosives have appeared in the literature during the last few yearsThis paper describes experiments concern- ing the mechanism of the explosive metal-cladding process. It has become increasingly important as a unique method for bonding metals and a typical cladding arrangement is shown in Fig. 1. A theoretical analysis of the mechanism of explosive bonding and a description of the nature and types of bond zones obtained was given by Cowan and oltzman." A further discussion of the basic principles of the process, a detailed description of the different bond-zone types, and extensive information on the properties and the applications of explosively bonded metals was recently published by Holtzman and cowan. " The process is now in commercial use by E. I. du Pont de Nemours & Co. The concept of the existence of a jet during metal bonding with explosives forms a central part in the theoretical analysis of the cladding mechanism described by Cowan and Holtzman When a layer of explosive is detonated on a metal plate that is separated from a second metal plate by a small distance the metal plate in contact with the detonating explosive is accelerated by the detonation pressure. An angle is established between the undeflected and deflected portions of the plate. Subsequently the deflected portion of the first plate collides with the second metal plate.

Jan 1, 1967

By Max Mason

IN 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ, one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect, which penetrates into the ground and is distorted and, reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in, reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert's study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to, reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are-spared the necessity of using a messenger, because nature has already provided one. For example, we already have a terrestrial magnetic field which auto-matically and continually conveys messages from underneath. We also have available the earth's gravitational field which furnishes us

Jan 1, 1927

By N. C. Fick, R. L. Rickett

Despite the large volume of literature on alloys of iron and silicon,' there is little published information dealing specifically with the constitution, at various temperatures, of the alloys containing less than 0.10 per cent carl~on and from 0.5 to 4.5 per cent silicon that are used extensively in the electrical industry. Because such information was needed by those engaged in the production of these alloys in sheet and strip form, the constitution nas determined of a series of commercial silicon steels containing 0.05 to 0.08 per cent carbon and 0.20 to 4.1 per cent silicon, over the temperature range 1300° to 1500°F. These alloys were all from regular production heats and of commercial quality. The results of the tests are given in Fig. I and for comparison the constitution diagram of iron-silicon alloys with 0.01 to 0.02 per cent carbon, taken from the literature, is also presented Material and Procedure All steels were hot-rolled to a thickness of 0.060 to 0.080 in. and used in this condition. Their chemical compositions, including over-all check analysis, and "center" analysis for carbon and silicon, are given in Table I. The so-called center analysis was determined on samples pickled to remove the outer surface and leave only the center third of the gauge thickness—the portion of the sample on which metallographic ratings were based. In most, but not all, of the alloys, slightly higher carbon was found at the center than when the whole strip was sampled; the two methods of sampling show relatively little difference in silicon. Two of the steels, A and E, contain relatively high phosphorus, while I and K are somewhat higher in manganese than the others. The procedure consisted essentially of heating specimens (about 1/16 by 3/8 by 3/4 in.), protected from oxidation or change in carbon content, at a temperature in the desired range and for a selected period, after which they were quenched in iced brine; the degree of transformation that had then occurred was determined by metallographic examination. The soaking periods were selected after preliminary investigation had shown that a con-

Jan 1, 1947

By Robley D. Evans, Gerald L. Schroeder

Advanced techniques for control of radon (Rn) daughter product concenrrations (working levels, WL) in the uranium mines are discussed. Understanding the physical laws which govern the flux of radon into a mine, the growth and decay of the radon daughters, and the particulate nature of the daughters when suspended in air allows ventilation personnel to improve the quality of mine air with no increase in ventilation rate. The task of controlling, in a mine atmosphere, the short-lived nuclides produced in the decay chain of radon is a unique problem and as such should be approached with ventilation techniques specific to the problem. For most mines this has not been the case. Rather, procedures for removing these airborne radioactive nuclides have been borrowed directly from ventilation experience in mines where dilution ventilation was the traditionally accepted approach for air purification. With radon daughter products, this has often led to frustrating difficulties and expense. Primary origin of the airborne radioactivity is the a-ray-emitting noble gas, radon (222Rn, Rn), a nuclide formed by the decay of radium (226Ra, Ra). Radon, being a gas, may escape from its parent crystal and diffuse through the parent mineral into the interstices of the rock body. In a sandstone structure, about 20% of all the radon formed may find its way into the interstices of the rock. If a cavity such as a mine is nearby, the radon may diffuse through the rock interstices into the mine. While radium is usually highly concentrated in uranium ores, it is also found in varying concentrations in all minerals. Radon is therefore present in all minerals. In normal glacial till, the equilibrium interstitial radon concentration often equals 5000 pCi (picocurie, also uuCi) Rn per liter of pore volume.' In normal granitic rocks, the interstitial radon concentration often approaches 30,000 pCi per 1. Considering these typical, high-radon concentrations, radioactivity from airborne of daughter products is a potential problem unique not only to the uranium mining industry and should be considered as a potential hazard in all underground environments.

Jan 1, 1970

By W. H. Emmons

Most mineral deposits change as they are followed downward on their dips. Some of these changes are due to primary arrangement; different ores were precipitated at different depths when the deposits were formed. Other changes are due to weathering or secondary enrichment. The chief changes resulting from weathering, in the main, are understood and standard changes are recognized. The processes are relatively simple. They take place at ordinary temperatures and pressures and can be duplicated in the laboratories. Moreover, there are thousands of deposits available for study, because the processes take place near the surface where the development of mines is begun. The changes due to primary arrangement of the deposits of the metals are not so well understood. Deposition has taken place at higher temperatures and our knowledge of the chemistry of the processes leaves much to he desired. Very few experimental data are available. The deposits, moreover, offer fewer examples because many mines are not developed to depths where the changes can be studied and a change to unprofitable material usually results in stopping work. Most students of ore deposits now accept, as confirmed, the hypothesis that nearly all lodes and related deposits were formed by solutions originating in intrusive igneous masses. Outward from these masses, the deposits at many places are grouped in zones and the arrangement noted from the intrusions outward are commonly the reverse of the changes noted from the surface downward in a single lode. A study of the changes in groups of deposits, from the parent intrusion outward, will throw light on the changes to be expected in a single lode downward. Recause the changes in series of deposits from the intrusive outward may all be observed near the surface, where more data are available, it is possible to increase the number of examples many fold and to apply the statisttical method of study with greater confidence of avoiding error. It is not everywhere possible to identify the parent igneous body to which a group of ore deposits are related. Several kinds of criteria are available; certain groups are superior to others. By applying the

Jan 1, 1924

By Walter S. McKee

When mixed with common cast steel in quantities ranging from 11 to 131/2 per cent. and properly treated, manganese increases the ductility of the metal and adds greatly to its toughness and resistance to abrasive action, which properties comprise the distinctive characteristics that make manganese steel so valuable for many purposes at the present time.. * At present the manganese-steel foundries of this country have an annual capacity of about 60,000 tons and most of the growth has occurred within the past 10 years. In the early days of the industry it was impracticable to make manganese castings weighing over a few thousand pounds, but at present crusher heads, rolling-mill pinions, and similar castings weighing up to 30,000 Ib. each are produced, and it does not appear that the limit of weight has been reached by a considerable margin. Manganese steel is similar in analysis to ordinary first-class converter metal except that it is high in carbon and contains from 11 to 13.5 per cent. of manganese. From one standpoint manganese steel is similar to malleable iron in that the casting as it comes out of the sand is hard and brittle and must be made ductile by a heat-treating process. The heat treatment is an essential part of the process of making manganese-steel castings and must be properly carried out to secure satisfactory results. The necessity for heat treatment limits the thickness of sections which may be made of manganese steel. Originally the annealing depth was comparatively small, but researches carried on during the past few years have resulted in an increase in the thickness of section up to 51/2 in., which it is possible to treat successfully. Large castings are cored out to a minimum thickness of 51/2 in., thus not only eliminating some of the internal stresses which are invariably set up in a very thick casting, but also reducing the weight and inertia of the piece, an important consideration if the casting is to be a moving part in a machine. At the same time, the thickness of 51/2 in. is sufficient to permit the use of manganese steel for the heaviest classes of machinery.

Jan 1, 1916

By Heihachi Kamura

In this research, the proper temperature for the reduction of iron ores by carbon monoxide was determined. Also, the difference of the rate of reduction on the sizes of ore under four mesh per linear inch was estimated, but no evidence could be found. Rates of reduction on the seven kinds of ore were compared with the results of the experiment, showing a close relation between reducibility and density of ore. Finally, the maximum size of ore that can be reduced in applicable length of time was determined. The author thinks that the process of production of steel may be replaced by low-temperature reduction of iron ores some time in the future. THE reduction of iron oxide, such as Fe203, to iron in the blast furnace is performed principally by carbon monoxide, but partly by solid carbon by the two following reactions: Fe203 + 3CO = 2Fe + 3CO2 2Fe203 + 3C = 4Fe + 3CO2 It is known that reduction by carbon monoxide takes place at a much lower temperature than reduction by carbon and that the reducing action of carbon monoxide progresses to the inside of the ore in lump form by gaseous diffusion. In the reduction by carbon, however, the reducing action takes place only at the contact surface of the ore and carbon, so that the more complete the reduction by carbon monoxide, the more efficient is the operation. However, the reduction does not progress as shown in the foregoing formula, because carbon dioxide acts oxidizingly on the metallic iron to such a degree that when the gaseous composition reaches a certain proportion of carbon dioxide to carbon monoxide, the reduction practically stops, even though the gases are moving slowly through the heated ore. The proportions of carbon monoxide and carbon dioxide in the gas depend on the kind of iron oxide and the temperature of reduction, also the duration of time in the reaction. The longer the time of the reaction, the higher the proportion of carbon dioxide obtained in the gas, but finally it will attain to a condition of equilibrium.

Jan 1, 1925

By Max Mason

IN 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect which penetrates into the ground and is distorted and reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert's study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are spared the necessity of using a messenger; because nature has already provided one. For example, we already have a terrestrial magnetic field which auto-matically and continually conveys messages from underneath. We also have available the earth's gravitational field. which furnishes us

Jan 1, 1927

By N. C. Fick, R. L. Rickett

DESPITE the large volume of literature on alloys of iron and silicon,1 there is little published information dealing specifically with the constitution, at various temperatures, of the alloys containing less than 0.10 per cent carbon and from 0.5 to 4.5 per cent silicon that are used extensively in the electrical industry. Because such information was needed by those engaged in the production of these alloys in, sheet and strip form, the constitution was determined of a series of commercial silicon steels containing 0.05 to o.08 per cent carbon and 0.20 to 4.31 per cent silicon, over the temperature range 1300° to 2500°F. These alloys were all from regular production heats and of commercial quality. The results of, the tests are given in Fig. I and for comparison the constitution diagram of iron-silicon alloys with 0.01 to 0.02 per cent carbon, taken from the literature, is also presented. MATERIAL AND PROCEDURE All steels were hot-rolled to a thickness of 0.060 to 0.080 in. and used in this condition. Their chemical compositions, including over-all check analysis, and "center" analysis for carbon and silicon, are given in Table I. The so-called center analysis was determined on samples pickled to remove the outer surface and leave only the center third of the gauge thickness-the portion of the sample on which metallographic ratings were based. In most, but not all, of the alloys, slightly higher carbon was found at the center than when the whole strip was sampled; the two methods of sampling show relatively little difference in silicon. Two of the steels, A and E, contain relatively high phosphorus, while I and K are somewhat higher in manganese than the others. [ ] The procedure consisted essentially of heating specimens (about 1/16 by 3/8 by 3/4 in.), protected from oxidation or change in carbon content, at a temperature in the desired. range and for a selected period, after which they were quenched in iced brine; the degree of transformation that had then occurred was determined by metallographic examination. The soaking periods were selected after preliminary investigation had shown that a con-

Jan 1, 1946

By C. A. Rowland, R. C. Nealey

Until recently there were very few dry grinding rod mills used. The early installations performed as anticipated. In the last seven years a number of dry grinding rod mills have been made, most of which have been used for grinding iron ore. The recent installations have not operated as anticipated in accordance with practices learned from wet rod milling. The paper does not establish any definite rules for the application of dry grinding rod mills but does attempt to establish some guidelines that can be followed. The paper reviews a number of flowsheets describing the problems encountered and some of the solutions found. Completely dried compared to partially dried feed is reviewed. Problems encountered in scaling up from pilot plant to production-size mills are described. Rod sizing, effect of rod length, rod bending, rod breakage, and rod tangling are discussed. While wet grinding rod mills have been used for 50 years to grind ores and make specifications sands, dry grinding rod mills have only recently come into significant use in the mineral industries. Among the materials now being processed in dry grinding rod mills are (1) lead sinter, lead slag, and limestone; (2) iron ore; (3) silica; (4) cement clinker; and (5) coke. Because the application of wet grinding rod mills was well understood at the time that dry grinding rod mills were introduced, the criteria and guidelines for selecting the former were carried over to the selection of the latter - in some cases with the anticipated results, but in many cases not. It is the purpose of this paper to describe, through a series of flowsheets, some of the recent problems encountered with dry grinding rod mills, to point out the solutions to these problems, and to set forth some guidelines for the selection and application of these mills. When dry grinding rod mills came into use, the following facts about their wet grinding counterparts were already well established: (1) The performance of large-sized mills can be accurately predicted from the performance of rod mills 5 or 6 ft in diameter. Wet grinding mills as large as 14 ft in diameter (inside shell) by 20 ft long with rods 19.5 ft long can operate satisfactorily.

Jan 1, 1970

By W. F. Flanagan, D. H. Polonis, S. D. Dahlgren

Rotation diffraction patterns of Cu-4.84 wt pct Si polymystalline samples were taken during the course of isothel-ma1 affing of the suPersaturated a phase, a diffraction spots were obserzled to streak during the initial stages of aging, and this streaking was similar to the streaking of a spots observed earlier by Barvett with deformed super saturated samples of the same composition. Although it was suggested that stacking faults were the sole cause of styeaking in the deformed samples, the present study has shown that plates with one small crystallite dimension can also contribute to the streaking when there is lattice coherency across close-packed planes. THE decomposition of the supersaturated a phase in Cu-Si alloys has been reported to occur by means of both thermal and stress activation.1-4 According to the Cu-Si phase diagram,3 Fig. 1, the supersaturated a phase (fcc) is expected to transform during aging by the precipitation of the y phase. The results of earlier studies2,4 have indicated that metastable k phase (hcp with nearly ideal close packing) forms initially at temperatures below the eutectoid temperature, after which the k transforms to the a and y phases. Hof-mann et al.4 have proposed a metastable version of the phase diagram, showing the approximate boundaries for k formation below the eutectoid temperature. In view of the close-packed nature of both the a and k phases, it is essential to consider the role assumed by stacking faults in the transformation. Streaking effects have been reported by Barrett 1 in the rotating crystal X-ray patterns of strained Cu-Si alloys and were attributed to stacking faults rather than particle size effects. This deduction was based on the observation that streaks in the diffraction patterns did not occur tangent to the 220fee Debye ring. It is known that the atom movements involved in faulting leave some X-ray reflections unaffected while others are broadened,' and, in particular, it has been shown that faulting will not cause streaking of 220fee reflections tangent to the 220fee Debye ring as would be expected if all the reflections were broadened.' The formation

Jan 1, 1967

By H. S. Bell

It seems unnecessary to dwell upon the advantages of the modern pipe still as compared with the older type of distillation equipment used by oil refiners. The relatively low installation cost, coupled with remark-able operating efficiencies of pipe stills, precludes the consideration of other types except in rare instances where some peculiarity of product or plant may have an influence. The question of the actual heat required to distil petroleum is quite involved. We have extensive data on the latent heats of the various hydrocarbons under different conditions of pressure. We also have information regarding the specific heats of various oils and the effect of temperature thereon. Because of the complexity of petroleum and of each fraction, it seems impossible to analyze theoretically the partisl-pressure effect of the great number of hydrocarbons upon one another during distillation. If a distillation curve and percentage analysis of any crude or product are available, it is possible to construct a curve with ordinates representing per cent. distilled and B. t. u. per pound or per gallon, or other desired unit. To do so the crude is split into fractions, of 5 or 10 per cent. The boiling point and gravity of each fraction being determined, it is possible to evaluate the heat required. As each fraction is removed, the residue must be raised to a higher temperature and latent heat supplied for the successive fraction. As the calculations progress, the latent heats decrease while the specific heats increase. Such a curve is illustrated by Fig. 1 for a typical 39.9° Be. North Texas crude. The chart is illustrative of batch distillation. Theoretically, if the oil were heated by a single flash in a pipe still, the partial-pressure effect of the light products would result in the removal of the same amount of vapors at a lower temperature. Practically, we find that because of the necessarily extensive fractionating equipment required when separating many products all in vapor phase, the oil has to enter the separator at temperatures corresponding to or even above those required in the batch still. Furthermore, in single-flash distillation the vapors evolved in the heater must be superheated to the outlet temperature. Very little is

Jan 1, 1928

By L. G. Huntley

The occurrence of oil or "tar" in Mexico was mentioned as early as the seventeenth century by Friar Sagahun, who gives the Indian name "chapopote," by which these asphalt seepages are still called. This asphalt was apparently used, as it has been used by primitive people in many parts of the world, in religious ceremonies and for medicinal purposes. Travellers also report that the ruins in Yucatan and the pyramids in southern Mexico show traces of the use of "chapopotel' as a building cement.l DeGolyer says that the first attempt to exploit oil or gas in Mexico in a commercial way is shown by the records of the Memoria de Fomento of 1865, when permission was granted to a Senor Ildefonso Lopez to exploit the deposits of petroliferous substances in the San Jose de las Rusias area in the State of Tamaulipas. Other concessions follow, and probably refer to surface seepages which occur in that district. This was several years after the discovery of oil in Pennsylvania. In 1868, a well 125 it. deep was :drilled by a company organized in Mexico City, in what is now known as the,, Furbero district, and a little oil was refined there. In 1873, residents of Tampico denounced seepages along the Tamesi River, and asphalt was mined near Tempoal in the Canton of Tantoyuca. No drilling was attempted. But between 1880 and 1883 several shallow wells were drilled for oil in Mexico, two of them being near the present Potrero de Llano field west of Tuxpam. The wells were drilled by a Boston company with Canadian rigs, and are said to have reached a depth of about 400 ft., while one is reported to have flowed. Several other abortive attempts were made to drill for oil between 1885 and the beginning of the present century, about which time the Mexican Petroleum & Liquid Fuel Co., Ltd., in which Cecil Rhodes was interested drilled 24 wells unsuccessfully, several of them as deep as 1,500 ft., in the State of Vera Cruz. Also Messrs. Doheny and Canfield of California pur-

Jan 1, 1916

By D. A. Thomas, M. F. Comerford

Poly crystalline wires of Fe-3.2 wt pct Si were cold-drawn to 31, 66, and 87 pct reductions of area. Mechanical properties and tnicrostructures were studied after recovery and re crystallization. An initial increase in strength during recovery was ascribed to strain aging, and subsequent softening was largely due to polygonization rather than re-crystallization. No unique actioation energies could be determined for the recovery process. Rather, activation energies ranged from 60,600 cal per mole at 10 pct recovery to 83,200 cal per mole when recovery was 50 pct complete. Sites for the nucleation of recrystallization were found to depend on time and temperature. In the early stages of re-crystallization, nucleation occurred in deformation hands. Later, or at high temperatures, recrystal-lized grains were nucleated primarily al grain boundaries. Polygonized structures did not seem to be preferred sites for nucleation. MUCH of the research on deformation, recovery, and recrystallization processes in bcc materials has been performed on single crystals or lightly worked polycrystals. Little study has been devoted to the relation of mechanical properties to micro-structure in polycrystals after severe deformation and subsequent annealing. This paper presents the results of a study of the tensile properties and microstructures of Fe-Si wires drawn varying amounts and annealed at a series of temperatures. EXPERIMENTAL PROCEDURE The experiments were carried out on an alloy of the following composition: 3.2 wt pct Si, 0.08 Mn, 0.016 C, 0.005 0, 0.0002 N, 0.0001 H, 0.008 P, 0.034 S. The material was received as l-in.-sq bars cut longitudinally from a hot-rolled slab provided by the Armco Steel Corp. The bars were forged to 3/8-in. rounds, centerless-ground to 0.250 in., and swaged to '0.108 in. All subsequent reductions were performed by room-temperature wire drawing at the rate of 2 in. per min. Each preliminary draft gave approximately 30 pct reduction of area and was followed by a l-hr anneal at 1010°C in dry hydrogen. Three lots of wire were made with ultimate cold reductions of 31, 66, and 87 pct reduc-

Jan 1, 1965

By W. H. Bassett

ALTHOUGH brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel- zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent. copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,1 the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard's work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.

Jan 1, 1927

By W. G. Matteson

The origin of the salt domes of the Gulf coastal plain has been investigated by many of the most able geologists, but the problem cannot be said to have been satisfactorily solved. Since 1860, numerous theories have been presented, only to be discarded, at least in part, as more complete infomation revealed their fundamental weakness. Real progress toward solution dates from 1902, when Hill1 advanced the theory of secondary deposition of the domal materials from saturated solutions of hot saline waters ascending from great depths under hydrostatic head along structural lines of weakness. Shortly thereafter, Harris,² using Hill's hypothesis as a basis, explained the doming and pronounced uplift associated with these salt cores as the result of forces exerted by growing salt crystals. This was a marked advance over the ideas of Coste3 and Hager,4 since no evidence of igneous intrusives, as they assumed to explain the uplifts, had been found associated with the domes. Harris5 developed his theory until it offered such apparently plausible explanations of so many details of dome phenomena that his hypothesis and conclusions received widespread acceptance, despite some serious objections, and today his theory, somewhat modified, is considered by many able investigators to be the best explanation of the origin of these domes. The immense production of oil per acre, the recognition of the high lubricating quality of the oil, the development and recognition of the efficiency and advantages of oil-burning vessels, with the subsequent exceptional demand for fuel oil, and the resultant advance in the price of coastal crude, have been responsible for a prospecting and develop- 1 Robert T. Hill: Beaumont Oil Field with Notes on Other Oil Fields of the Texas Region. Jnl. Franklin Inst. (1902) 164, 143. 2Gilbert D. Harris: Rock Salt in Louisiana. Louisiana Geol. Survey Bull. 7 (1907) 76. ³E. Coste: Volcanic Origin of Natural Gas and Petroleum. Jnl. Canadian Min. Inst. (1903) 6, 73. 4Lee Hager: Mounds of the Southern Oil Fields. Eng. & Min. Jnl. (July 28, 1904) 78,137, 180. 6Gilbert D. Harris: Geologicel Occurrence of Rock Salt in Louisiana and East Texas. Econ. Geol. (1909) 4, 12.

Jan 1, 1921