Search Documents

By Felix B. Shay

THE Agua Fria mine is in eastern Honduras at Lat. 140° 06' N., Long. 86° 36’ W. Danli, the seat of the local municipal government, is the nearest town. The property is approximately 44 miles east of Tegucigalpa, the terminus of a truck road from the Pacific coast. The mine lies at an altitude of 3300 ft. with surrounding elevations as high as 6000 feet. For 20 years the oxidized croppings of the Agua Fria vein had been worked intermittently when in 1927 an attempt was made to open the property. A shaft was sunk 300 ft. and considerable ore was blocked out, but before a mill could be installed financial difficulties arose and the mine reverted to the original owners. Erle P. Halliburton, of Los Angeles, purchased the property in 1934. At that time a careful consideration of all factors involved showed that air transport was the only practical method of moving the equipment and machinery necessary to commence production. The other alternative was by muleback, which required sectionalizing all equipment to a maximum load of 200 lb., and during the rainy season this type of freighting was subject to serious delays. It was decided to purchase a trimotor Ford powered by three Pratt and Whitney Wasp B motors developing 400 hp. each. There were several reasons for the choice: (1) this type of plane was available at a reasonable price, owing to its replacement by faster models on most of the airlines in the United States; (2) the ship was capable of carrying a pay load of 3000 lb. over the required distance; (3) since this airplane had been widely used there would be no difficulty in securing competent personnel or in purchasing spare parts. It was necessary to rebuild the plane for cargo service. The windows were removed and the fuselage was entirely covered. A hatch was cut in the top of the fuselage to receive heavy crane loads and pieces of freight that were too large or too long to go through the rear door. The seats were removed and the interior of the plane was lined with Duralumin sheets. A heavy-duty landing gear was installed and the floor was reinforced. The nearest site for an airport was two miles north of the mine. The necessary grading was done by a small track-type tractor with a wheeled grader, which was brought in overland. Six weeks was required for bring-

Jan 1, 1940

Discussion of the paper of E. L. deGolyer, to be presented at the Colorado meeting, September, 1918, and printed in Bulletin No. 137, May, 1918, pp. 987 to1000. J. A. UDDEN,* Austin, Tex. (written discussiont).-I have read Mr. E. L. deGolyer's paper on The Theory of Volcanic Origin of Salt. Domes, with a great deal of interest. It seems to me a very able summary and discussion of the various theories set forth to account for the origin of our salt domes on the coast. It has always appeared to me that what we need is more observations on the facts involved and I regret very much that so far we have not been able to devote much time to the study of our salt-dome fields on the coast in this State. One feature that I do not find mentioned in Mr. deGolyer's paper is the so-called "cap. rock" overlying the salt. The nature of this rock seems to vary from a coarsely crystalline limestone to a fine-grained limestone containing sand and in which the limestone seems to be intersticially introduced material. We should be prepared to accept, if necessary, "more than one theory. To my mind, the igneous theory and the artesian theory, if I may so call it, may very well both be true. The "squeeze" theory and the artesian .theory may,, it seems tome also, jointly explain the phenomena. Neither the volcanic nor the salt "squeeze" theory explains the presence of the cap rock. The latter certainly does not explain the extensive sulphur deposits which occur in association with the cap rock. Whichever additional theory will be found best to explain the salt-dome structures, when we shall know them better, it seems to me that the theory first advanced by R. T. Hill and later elaborated by G. D. Harris, is not likely to be entirely replaced. Whatever cause has first set into action an upward circulation of gases and liquids in our salt domes, it seems to me that to a gentle circulation of the kind postulated by their theory is to be ascribed the uppermost and the later phenomena in our salt domes on the coast, with which we are most familiar; such as the cap rock, the sulphur, and the gypsum and anhydrite deposits.

Jan 7, 1918

By Alfred James

John Stewart MacARthUr, born in 1856, was the son of Robert MacArthur of Glasgow, and came of Scots stock distinguished for character and religious conviction. His election as elder of the Free Kirk gave him greater pride than the receipt of the gold medal of the Institution of Mining and Metallurgy. The former honor was for character— it marked him as a son worthy to follow in his father's footsteps; the latter was awarded for his life work of eminent service to the gold industry. Cheery optimism, resolution, tenacity of purpose, and industry ever characterized his actions. Apprenticed to the Tharsis Sulphur & Copper Co., his work on the chemical staff brought him to the notice of the Cassel Gold Extracting CO.,. at that time struggling with an unworkable electrolytic process..He was engaged by that company, in 1886, as technical manager and before long brought out the perchloride process, which was speedily followed (in 1887) by the epoch-making cyanide process. This process revolutionized gold mining and directly led the way to the elevation of the mining engineer to the most broadly trained product of the engineering profession. A noteworthy feature of the cyanide process was its completeness when introduced. Over thirty years have elapsed and the use of the process has been worldwide, but no suggested improvement has stood the test of time. The extension of the process to the beneficiation of silver ores—containing far more metal per ton and thus requiring the employment of stronger solutions—has brought us the Merrill and Crowe improvements in precipitation and the Nipissing desulfurization process for certain silver-hearing minerals. Roasting apparatus, fine crushing, filtration, and settling equipment have all aided the extension of the process in and from its original field. As Hennen Jennings put it,, the cyanide process today is essentially that of 1890. This self-containedness of the cyanide process arose from no mere chance; it was directly due to MacArthur. It was he who personally investigated every known method of precipitation and then every form of zinc from sheet, punchings, filings, millings, rods and shaving down to fume; it was he who investigated the effect of protective alkalies, of so-called accelerators, and of the addition of lead salts; he was determined to leave nothing to chance.

Jan 1, 1921

By Dennis K. Mortensen

The Role of the Operator The ultimate objective of any installation is to be able to accomplish the useful work that it was originally designed for. The operator needs a tool that he can both operate effectively and maintain efficiently. The overall design and subsequent installation of a comminution circuit should be a marriage of good engineering practice and practicality. Since the operator must operate and maintain his equipment, his input into the design and installation is vital to its ultimate success. The design of a crushing or grinding circuit is dependent upon many factors including flowsheet design, equipment selection, physical layout, space restrictions, climatic restrictions and considerations for future expansion. The operator must live on a day-to-day basis with the results of the final design and installation. The most satisfactory operation will result when the operator has a major input into each of the criteria that are used to define the final design and installation. The operator referred to is not only the mining company or organization that is having the installation built for its specific use but, more specifically, the person or persons that will actually be responsible for its daily operation and maintenance. Future references to the "operator" will include those individuals with that daily reponsibility. The operator's input into the installation of the circuit is of equal importance to his input into the design. The engineering organization which puts together all of the various design drawings for circuit installation is generally restricted to trying to get all of the details onto a multitude of 24" x 36" two dimensional drawings with a few isometric drawings thrown in. It's almost impossible to get all of the details of a final installation onto all of the drawings, and field modifications are necessary to make everything fit properly. In a multilevel installation, such as a grinding or crushing circuit, it is difficult to envision space requirements to adequately operate and maintain the various pieces of equipment simply by looking at a set o£ drawings. For some designs it is helpful to build a scale model so that a more realistic view of what the installation will look like can be seen. The scale model allows the operator to make whatever changes in design are needed to operate and maintain his equipment most effi-

Jan 1, 1982

By H. Rush Spedden, Arvid Thunaes

Pilot plant test work in 1942 and 1943 showed that by a combination of deslim-ing, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants. IN the past, mills treating ores of tin and tungsten by gravity concentration have recovered very little mineral finer than 325 mesh, although some form of slime concentration has been generally attempted by the use of buddies or round tables. This paper describes a series of pilot plant tests made in 1942 and 1943 in which the use of the Sullivan deck was investigated for the recovery of an appreciable amount of the fine values formerly lost. The investigation was initiated by the U. S. Government in an effort to increase the wartime production of tin. Bolivian milling practice at that time included jigging of the coarse sizes, tabling of the intermediate sizes on conventional shaking tables, and the use of buddies or round tables on the finest sizes. Flotation of the pyrite was employed at different stages of the treatment, depending upon the quantity present and the preference of the operator. Usually good recoveries and the bulk of the production were made in the jigging and tabling operations provided that these sections were not overloaded. Buddies and round tables were used for a small additional recovery if it could be shown that they could pay for their high cost of operation. Extensive test work established that by a combination of desliming, classification, and Sullivan deck treatment, cassiterite as fine as 10 microns (1500 mesh) could be recovered when proper conditions were maintained. This test work has been verified by several full-scale installations. The method is generally applicable to the preconcentra-tion of large tonnages of low-grade ores or tailings for the recovery of a small amount of a valuable heavy mineral. The Sullivan deck (or now the Denver Buckman tilting concentrator), which is the essential part of the method, was devised originally for the recovery of tin from tailings of the Sullivan concentrator, Kimberly, B. C. Since the material treated contained only 0.05 pct Sn, it was impractical to attempt to recover cassiterite finer than 500 mesh.*

Jan 1, 1951

By R. T. Pepper

DURING an investigation into the effect of heat-treatment on the creep properties of the magnesium alloy ZW1, (1 pct Zn, 0.6 pct Zr), the previously published methods of final polishing were found to be unsatisfactory. A new diamond-polishing technique has been developed to facilitate the study of fine precipitates in this and other magnesium alloys, and is described in this note. The sectioning and coarse grinding techniques are those of Fox and Hall,' and Hess and Cieorge.' Pre- liminary mechanical polishing is done with 6-µ, and 1-µ( grades of diamond compound on 'Microcloth' using a lubricant of 'Hyprez' oil. When the conventional technique is used with a 1/4- µ diamond wheel for the final polishing of magnesium alloys, scratching is likely to result from the abrasive action of the 'Microcloth' nap on the soft metal surface. This problem has been overcome by the use of a cream on the wheel in order to separate the specimen surface from the polishing cloth. To prepare this cream, a solution of 6-ml tri-ethanolamine in 75-ml water is stirred into 12.5 g stearic acid at a constant temperature of 80° to 90°C. The cream is allowed to cool, and is then 'whipped' to a smooth consistency with 100-ml 'Hyprez' oil. Before polishing, the diamond loaded 'Microcloth' is moistened with a few drops of 'Hyprez' oil, then a small amount of cream is worked into the nap. For the best results a wheel speed of 500 rpm should be used for polishing, and the specimen should be held by hand with a light pressure while being rotated in the opposite direction to the wheel. After polishing it is necessary to swab the specimen thoroughly in methylated spirits to remove residual cream and oil from the surface in order to avoid uneven etching and drying stains. Fig. 1 shows the surface finish obtained on a specimen by polishing on a 1/4- ° diamond wheel using the cream, and Figs. 2 and 3 the precipitate observed in ZW1 after polishing, and etching for two seconds in nitric acid 15 pct in ethylene glycol. This new diamond-polishing technique has made a valuable contribution to the programme of metal-lographic research on ZW1 and has become a routine laboratory practice for other low alloy content magnesium alloys.

Jan 1, 1961

By H. W. Reid

One of the outstanding features of the year was a further marked decline in the footage drilled. This is estimated at 169,000 ft., as against 218,000 ft. for the previous year, and 372,500 ft. in 1930. Owing to repair work and improved production methods, there was an increase of about 4.25 per cent in the amount of oil won, the production being estimated at 10,160,000 bbl., or an increase of 400,000 bbl. over 1931 and nearly 750,000 bbl. more than in 1930. (See Table 1.) At the end of November there were 28 rigs in operation. During the first 11 months of the year 54 new wells were started; the average depth of those completed was 2476 feet. Owing to the continued restriction of drilling programs there has been little of outstanding interest in the way of new plant or technique. The use of the acid bottle, for testing the verticality of wells while drilling, has increased considerably, and this is now in use in practically every well except the very shallowest. During the last six months of the year fairly extensive use has been made of electrical coring. The number of wells started in the Colony up to the end of November, 1932, was 1894. The average number of producing wells during the year was 789, or 41.7 per cent of the total. Of these, 214 were flowing wells, 473 pumping, 80 bailing or swabbing, and 22 were produced by air or gas-lift. Although the last category represents less than 3 per cent of the total, there has been a marked increase in the use of air or gas-lift as compared with 1931. During the year there were 16 companies engaged in producing oil, as compared with 14 in the two previous years. In addition to one small refinery which started to operate at the beginning of the year, the five existing refineries worked continuously. At the latter very little has taken place in the way of extensions, except at one in the Parry Lands—Pitch Lake—Point Fortin area, where extensive alterations and additions are in progress, including the building of a deep-water pipe-line pier. When this is completed there will be five loading terminals, all situated in the sheltered Gulf of Paria, or west, coast, capable of accommodating ocean-going tank steamers. There

Jan 1, 1933

By Arthur B. Foote

The cams at present universally used in stamp mills lift the tappets with an involute form of curve, to which the surface of the tappet is always tangent; moreover, the line of contact between tappet and cam, if produced, would pass through the center of the stem. This is no doubt a desirable feature, but the writer has long believed that it would be much more desirable if the cam were to pick up the stamp without shock, and gradually increase the upward velocity of the stamp throughout its upward movement. The involute form of cam attempts to impart instantly a considerable upward velocity to the stamp, starting it from a state of rest, and the result is a destructive blow, a great deal of noise, and much wear and vibration. The writer has developed a form of cam which will lift the stamp pith a motion similar to that of the piston of an engine between the end and middle of its stroke; in other words, harmonic motion, from the woint of zero to maximum velocity. The curve will give this ideal motion only when the stamp is set for the exact drop for which the cam was designed, but the improved cam will not be as bad as the involute cam until the drop is reduced one-half. In other words, if a cam is designed for a 6-in. drop, it will be some improvement over the usual form of cam until the drop is only 3 in. Any cam, whatever its form, must of course lift the stamp in the same number of degrees of revolution; therefore, with this new form, since the stamp starts more slowly on its upward course, it must end up by going faster, the average speed being the same as with the involute cam. The stamp, after it is no longer in contact with the cam, keeps on going up a certain distance, which is easily calculated. It is therefore possible to hang up a stamp without a cam stick, if the fingers are not more than + in. longer than necessary to hold the tappet above, the cam. With this design of cam the surface of the tappet is not tangent to the surface of the cam throughout the lift. The possible consequences of this were studied with a full-size model, and did not seem serious, as

Jan 1, 1915

By Walter Kauzmann

EyRing'S general theory of shear rates as a function of the properties of molecular units of flow is outlined and applied to the creep of metals. This theory regards the unit molecular processes involved in the flow of matter as typical chemical reactions requiring an energy of activation in order to proceed. The externally applied stresses are assumed to influence the rate of flow solely by lowering the activation energy for flow in one direction and raising that for flow in the other, owing to the work that is done by or against the external forces in going from the normal to the activated state. The rates of flow in the two directions are then no longer equal arid there is a net, macroscopically observable flow in one direction. This is understood to be the physical basis for the well-known exponential dependence of the creep rate on the stress. The amount by which the activation energy is raised and lowered by a given external stress is directly related to the molecular dimensions of the unit of flow, so that some insight into these call be found from the behavior of the strain rate with changing stress. When Eyring's equation is applied to the flow of ordinary liquids, such as water or benzene, it has been found from the values of the constants required to fit the observed data that the unit molecular process here involves the passage of single molecules by one another. In metallic creep, on the other hand, the unit molecular process is shown probably to involve the shear of rather large blocks of material (100 to 1000 or more atoms on a side). This agrees with present ideas of crystal flow by means of dislocations such as have been presented by Taylor, Oroaan, and Polanyi, as opposed to flow by a mechanism related to that taking place in atomic diffusion. The dimensions of the dislocations are found to depend markedly on the temperature. The questions of why some metals are so much softer than others, the effects of impurities on hardness, the softness of single crystals, and the role of self-diffusion in creep are considered in the light of the theory and it is shown how answers to these questions (and others similar) might be obtained by use of the theory.

Jan 1, 1941

By Arthur F. Wendt

The hot-blast oven of which the accompanying plate gives complete details, was designed by the writer for the spiegel-furnace of the Lehigh Zinc and Iron Co., at Bethlehem, Pa. Members of the Institute who visit these works will have occasion to notice the large amount of zinc-dust in the gases, and the consequent dirtiness of both the hot-blast and the boilers. The zinc collects in a crust on the iron hot-blast pipes and leads to the frequent burning of them. A large vertical standing-pipe stove, a modification of the "Pleyer," thus gave considerable trouble by the burning of pipes and, on one occasion, the toppling over of a whole row. These inconveniences are avoided in the hanging-pipe stove under consideration, and less heating-surface has been found to be required to heat the blast to a given temperature. The construction of the stove is so simple and so plainly shown in the plate that it is needless to enlarge upon it. Each pipe rests in a box and is connected by U-branches with the next adjoining pipes. An iron sleeve is placed around the joint and tightened, as usual, with iron filings. In case of a pipe burning out, that particular section is cut off by the valves and the sleeves are broken. The pipe is then readily lifted out of the box and a new one is substituted. The whole operation requires only a short time and the section can then be at once put into use. The boxes supporting the pipes cover the whole surface of the hot-blast and are closed by iron covers rammed with fire-clay. Owing to the air-space around the U-pipes there is little loss of heat in the upper part of the stove. Each section as built has 280 square feet of heating-surface. The furnace is blown by a horizontal engine with 46-inch stroke and 48-inch diameter of blowing-tube. At 28 to 30 revolutions, the engine delivers 3000 cubic feet of air per minute, at a pressure of 5 pounds. When five sections of stove are in use, the blast enters the furnace at a temperature of 850" F. That is, there are over two cubic feet of air per square foot of heating-surface heated to that temperature per minute.

Jan 1, 1887

By P. W. Davies, B. Wilshire

PREVIOUS investigations on the effect of stress changes on the high-temperature creep and fracture behavior of metals have been confined mainly to the testing of complex alloys.172 Most of these alloys are structurally unstable during creep because of such effects as recrystallization, overaging, and so forth, so that the results are of limited application. The only pure metals on which observations have been made appear to be lead3,4 and aluminum5 tested under conditions which allow rapid recovery to take place. The present work describes the effect of a single stress change on the creep and fracture properties of a metal in which recovery is very slow. A Ni 0.1 at. pct Pd alloy was used so that grain growth and recrystallization did not occur during creep testing. Specimens of this material were heat-treated to give a uniform grain size of 10 grains per mm. Creep tests were carried out at 500°C using Denison T.47 machines; details of the creep-testing procedure have been given elsewhere.' All specimens were tested at a constant initial stress of 5 tpsi which gives, in an uninterrupted test, a minimum creep rate of ~10-3 pct per rnin and a life of -7000 min. Specimens were loaded under these standard conditions and after 1500 min, when secondary creep was well-established, the stress was changed to either 8, 7, 6, 4, 2, or 0 tpsi for a period of 180 min. After this time the original load was reapplied and the tests continued to fracture. The results are shown in Fig. 1. No detectable creep occurred during the period of reduced load, even at 4 tpsi, and on reverting to 5 tpsi the creep rate returned to its original value immediately. Increasing the stress to 8, 7, or 6 tpsi resulted in an instantaneous extension followed by a period of transient creep leading to a new steady creep rate. On returning from these higher stresses, the resulting creep rate at 5 tpsi was very low compared with the original value. Furthermore, the higher the stress during the stress change, the lower was the final creep rate. It is significant that the rupture life is comparatively unaffected by any of these stress changes.

Jan 1, 1965

By Alexander Knoll, Dwight L. Baker

THIS paper is a report on work undertaken to investigate the results and conclusions of Ravitz and Porter1,2 that galena freed of surface oxidation products and lead carbonate ("clean" galena) is waterrepellent, and that the action of xanthates in flotation is the action of a cleansing agent, enabling oxidized galena particles to expose a pure lead sulphide, water-repellent surface. The apparatus, in construction and use, was essentially that of Ravitz and Porter. The only significant modification introduced by the present authors was the substitution of a three-necked flask for the flotation cell as the "reaction vessel." Our procedure was to place 50 grams of freshly ground, minus 200-mesh galena in the reaction vessel, sweep out all molecular oxygen from the system with oxygen-free nitrogen, and proceed to wash the galena surface free of its oxidation products with repeated small portions of (I) ammonium acetate (500 c.c. of water, 200 grams of ammonium acetate) or (2) ammonium chloride, hydrochloric acid (2 liters containing 200 grams of ammonium chloride and 25 c.c. Of 1.18 sp. gr hydrochloric acid). The galena was next washed with many 100-c.c. portions of oxygen-free, distilled water. The galena was finally considered free of soluble salts when wash water that had been in contact with the mineral for at least 48 hr.* gave negative tests for: (x) lead ion with sulphide; (2) chloride with silver ion; (3) acetate with cuprous chloride, sodium chloride; and (4) ammonium ion with Nessler's reagent. Next 500 c.c. of potassium ethyl xanthate solution, free of dissolved oxygen, was run onto the "clean" galena particles. For this system there were determined: I. The wetting properties of the clean galena particles by shaking the reaction flask and noting the degree of mineral collection at the liquid-air interface. This was, of course, simply a qualitative test, but it proved adequate for our purpose. 2. The removal of xanthate ion from the potassium xanthate solution on being shaken with the "cleansed" mineral. Xanthate concentrations were determined by iodine titration according to the methods of Taylor and Knoll.3 3. The pH of the xanthate solution after having been shaken with the "cleansed" galena. The pH was determined colorimetrically.4 The results of five experiments of the type mentioned above are given in Table x.

Jan 1, 1941

By J. Parke Channing

The Miami orebody occurs in an altered Pinal schist. It is popularly known as one of the '(porphyry " deposits but, as at Inspiration and Ray, the ore is an altered mincralized Pinal schist. The orebody mined is the zone of secondary enrichment. Speaking in general terms, the area of the orebody at Miami may be considered as 1000 ft. long and 800 ft. wide. The vertical thickness varies from 200 to 400 ft., so that it is an extremely irregular mass. The study of the ground movement and resulting subsidence at Miami is complicated by the fact that the formation is not homogeneous throughout the mining area, the orebody terminating on its eastern extremity at a fault plane adjoining the Gila conglomerate. This conglomerate is a recent sedimentary deposit somewhat analogous to glacial drift and consists of boulders of granite, schist, and other material cemented with clay, and at times is quite hard. The fault dips eastward at an angle of 45". The original method of mining was top slicing, the slices being 10 ft. thick. At first, there was a good deal of experimenting with mining methods. Some undercut rooms were tried, and the stopes were filled with broken ore with the idea of removing intervening pillars by top slicing. The adoption of the top-slicing method in itself involved considerable experimenting, including some experiments with a long-wall system. The method finally adopted involved the operation of top slicing areas 250 ft. square, each with a central supply raise and ore-gathering raises, each block being worked as a unit. Mining operations in the Captain orebody, which connects with the boundary of the Inspiration property, were started by the room-and-pillar system, the rooms extending across the orebody, with widths of 10 to 15 ft., with 15- to 10-ft. pillars between. The intent was to operate the rooms as shrinkage stopes, permitting the pillars to crush when the ore was drawn from the rooms. It was found that the shrinkage stoping was unnecessary, so a system of block caving was adopted. This system was so successful in the Captain orebody that, about three years ago, the method of mining in the orebody was changed from top slicing to block caving, the method now in use. The block caving system, as practiced

Jan 1, 1923

By Alexander Deussen

The figures listed in a table for Gulf Coast fields given by L. P. Teas1 in 1934 are so greatly at variance with results that I have obtained from a serious study of this subject over a number of years, that I am disposed to challenge the correctness of Mr. Teas' figures as an accurate representation of acre-foot yields of Gulf Coast fields, and as regards at least two of the fields listed by Mr. Teas I desire to "put into the record" some figures that, according to my study, are more nearly in accord with what I conceive to be the actual facts. Upon investigation I find that Mr. Teas' figures, inadvertently no doubt, arc not what they purport to be. Apparently the figures were arrived at by considering as thickness of the producing formation the net thickness of producing rock corresponding "to the total of the net portions of the producing zones which actually yield oil into the drill hole"—and in following this method I am under the impression that Mr. Teas was acting under instructions of the Institute in the preparation of this paper, in order to get comparable figures from the several fields of the United States. Apparently the author interpreted these instructions to mean that in the absence of cored thicknesses of producing horizons the actual number of feet of screen set in the various producing zones was to be taken as the basis for arriving at the thickness of these zones and the "acre-foot" yields. It is obvious that in many instances only 20 ft. of screen, or even 10 ft. of screen, might be set in a well, when there might be actually 100 ft. of oil sand present. In the early operations in the Gulf Coast it was usual to set much less screen than the amount of sand. It follows that the "acre-foot yields" so arrived at would be much greater than those found by using the full amount of sand. In Mr. Teas' table, it was indicated that up to the end of 1933 "acre-foot" yields had been obtained in the several fields as listed in Table 1. A casual inspection of these yields will show that certainly they do not properly reflect the amount of oil produced from an acre-foot of the

Jan 1, 1936

By V. R. Garfias, R. V. Whetzel

It has been repeatedly questioned whether estimates of oil reserves are of any practical value, as the greater number of such calculations previously made have subsequently been proved to be grossly inaccurate. But even admitting partial justification for such statements, it must be evident that some idea, however approximate, of the available reserves of essential minerals—petroleum included—is of vital importance in mapping their development and the future trend of the related industries, particularly if it is kept constantly in mind that these estimates are not only never intended as a final word but must continually be subject to revision in accordance with the changes in their component factors. The value of these estimates, therefore, hinges on the clear understanding of what is meant by reserves and that the figures can only apply within the limited time when the controlling factors remain unchanged. It should be understood, further, that while estimates of possible and probable oil deposits are as a rule but idle conjectures, appraisals of proven oil reserves can undoubtedly be made with an ever-increasing degree of accuracy. And it is with this in mind that in the present study the endeavor has been to estimate only the world's proven oil reserves and to leave out of consideration the questionable volume of the probable and possible oil reserves. Such a survey presupposes further a clear distinction between the known amount of oil underground in proven fields at any one time, and the proven reserves: the portion that can be economically brought to the surface and made available for utilization. Only a fraction of the petroleum stored underground in proven fields— usually associated with natural gas—is or can be economically brought to the surface, and not all of the oik brought to the surface is economically utilized; also, although practically all the natural gas can be economically recovered and utilized, in actual practice a large part of the total volume that reaches the mouth of the well is wantonly blown into the air and wasted. It is thus estimated that in the United States only some 25 per cent of the petroleum stored underground in proven fields is actually brought to the surface; and in actual practice close to 25 per cent of the total gas produced is now absolutely wasted. And the dissipation of this

Jan 1, 1936

By C. K. Leith

QUOTING from Dr. Richard T. Ely:1 "Conservation, narrowly and strictly considered, means the preservation in unimpaired efficiency of the resources of the earth; or in a condition so nearly unimpaired as the nature of the case, or Wise exhaustion, admits. And broadly considered, it means more than the word itself implies, for it naturally includes an examination of methods Whereby the natural inheritance of the human race may be improved; and still more broadly considered, and as used in popular discussion, it includes a treatment of the effects of productive conservation methods upon distribution. "Conservation means a sacrifice of the present generation to the future generations Whenever it is carried too far. There is a sharp limit to the economic sacrifice that we may reasonably ask the private person to make for even the present Welfare, and the limit is still sharper when we come to consider the interests of future generations." In a paper on the iron ores of America, presented to the Pan-American Scientific Congress at Washington, I have emphasized the fact that the reserves of iron ores in the two Americas are enormously in excess of the requirements of the present generation, in fact, so large that no shortage is to be anticipated for many generations in the future; that a large part of the value of iron ores is put into them by man's efforts to make them available. This fact is fundamental for the intelligent consideration of- policies of conservation as applied to iron ore. As I interpret it, this fact makes it practically unnecessary that the present generation should make any especial sacrifice for future generations in the way of conservation of its iron-ore resources. Even if we were disposed to look forward to a period of 100 or 200 years, with a view to insuring the welfare of the people living at that time, it is doubtful whether any procedure we could now formulate would materially help them in the matter of iron ores, so large are the reserves available. In order that an appeal for conservation may be effective it must obviously favor the welfare of the present or immediately following generations; it must promise benefits to general and individual welfare during a period within the range of comprehension of the average man.

Jan 2, 1916

By Warren L. Howes

Literally hundreds of designs of mill liners are in use in current grinding operations, varying in contour from smooth to the roughest of surfaces, and in materials from scrap rail to alloy steels. A certain amount of variation in materials can be expected, owing to differences in local market conditions and the character of ores. However, when one attempts to rationalize the designs in current operations of a parallel nature, there is little that can be called standard practice. Designs and opinions of designs are as divergent as day and night. Somewhere in this maze there must be dues to better practice. The purpose of this paper is to examine the factors for consideration in liner design, and to propose a vigorous campaign of exploration in this phase of grinding operations. The paramount considerations in the choice of mill liners for a grinding operation are: (I) durability, in view of the cost, and (2) developed grinding capacity. Because of the strategic nature of grinding circuits in controlling the production of most mining operations: grinding capacity usually is the greater consideration. Grinding Capacity Mill liners affect grinding capacity in two ways: (I) by establishing dead space within a mill shell, which could be usefully occupied by live grinding media, and (2) by controlling the grinding action of the media. The extent to which liner thickness affects the potential volume of live grinding media, and thereby the grinding capacity, is shown in Table I. In a ball mill 7 ft. in diameter, for example, an inch of liner thickness reduces ball volume and corresponding grinding capacity by 5 per cent. With grinding capacity at a premium, this makes consideration something more than first cost of liner materials. A low-cost, voluminous material, made extra thick to secure adequate life, can be very expensive in terms of grinding capacity. On the other hand, in increased grinding capacity, a long-wearing material in a thinner pattern can save many times its value. From the standpoint of mechanics, the function of mill liners is to provide the means of driving or tumbling the load of grinding media. In this respect, an internal-spur gear-and-pinion assembly resembles a rotating mill shell with its contained load of grinding media, the mill-shell linen

Jan 1, 1947

DAVID COLE, El Paso, Tex. (communication to the Secretary*).-I notice that Mr. Callow takes issue with me on certain points I have previously contributed to the Transactions, to which I would reply," follows: Regarding Inspiration: Mr. Callow's refinements of gravity methods made just prior to the advent of flotation in the Southwest were intended to be "down to the minute," and the gravity flow sheet for Inspiration ores which he brought out at that time as the result of his long campaign of experimentation was regarded by many as the last word in wet gravity work. It was not my intention to discredit this good work when I said "he threw small light on slime treatment." "Minus 200 mesh," however, is not-synonymous with "real slime." Repeated treatments by gravity methods will result in the separation of a very large percentage of the fine granular sulphides in sizes much finer than 200 mesh, and I gave him due credit for that. The unavoidable losses were made in the "real" slime which I mentioned in the paragraph which Mr. Callow refers to as my "statements on page 1871," and his refinements were not a solution to the real slime problem. Mr. Callow has called attention to the fact that his best results at. Inspiration in gravity work were obtained on Joe Bush ore and he presents a table, viz., Tests Nos. 68, 71, and 72; and asks us to consider and compare these results, made by his refined gravity methods, with the results obtained by 'flotation methods in the new mill "during the second half of 1915 and in August, 1916." Of course, the ore treated in the mill was what happened to come. It was not Joe Bush ore, and therefore comparisons of detail figures are of no value. In regard to Mr. Callow's statements under the caption "Callow Cells Adopted by Arizona Copper Company," I would say that those who have been sufficiently interested to read my paper and' his remarks will notice what amounts to contradictory statements on several points which I cannot allow to go unchallenged. I was on the ground constantly and got my information at first hand. The tables published were the official ones. Mr. Callow was not present during the period and has been laboring under that disadvantage.

Jan 5, 1917

By J. Chipman, H. A. Wriedt

DURING the past twenty years, a considerable background of knowledge has been built up on the chemical behavior of oxygen in liquid iron. Little is known regarding oxygen in liquid nickel or the effect of nickel as an alloying element on the behavior of oxygen in liquid steel. The solubility of oxygen in liquid iron was determined by Fetters and Chipman' and, more precisely, by Taylor and Chipman.' The Ni-NiO eutectic was placed by Merica and Waltenberg"' * at 1438°C and 0.24 pct 0, and this point has been confirmed by others." O It was reported by von Bohlen und Halbach and LeitgebelT that nickel and its oxide are miscible in all proportions at 1600°C, but this report is discredited by observations of others. The melting point of NiO according to von Wartenberg and ReuschV s 1990°C. Approximate values of oxygen solubility at several temperatures were reported by Hensel and Sc0tt.O The data of Krupowski and Balickil0 are inconsistent with those of Hensel and Scott and indicate a solubility less than half that found in the present study. For oxygen solubility in Fe-Ni alloys under pure iron oxide-nickel oxide slags, only the scattered data of von Bohlen und Halbach and LeitgebelT are avail- able. The careful work of Bardenheuer and Brauns" involved silica-saturated slags. The equilibrium between Fe-Ni alloys and iron oxide-nickel oxide slags was studied by zur Strassenu and by Jander and Senf,u but no oxygen analyses were reported. Oxygen in Pure Nickel Apparatus and Nlethod: Samples were taken with a "Taylor sampler" from a bath of molten electrolytic nickel held under an air atmosphere in a magnesia-lined 30 lb induction furnace. Saturation of the melt with oxygen was effected partly by the addition of chemically pure black nickel oxide and partly by the air atmosphere. Samples were taken only when there was a clearly visible oxide phase present. To avoid contamination of this oxide phase, the silica-sheathed Pt—Pt-10 pct Rh thermocouples, by means of which temperatures were measured, were immersed in the melt for the minimum time consistent with accurate reading. Samples and temperature readings were taken only after the furnace had been

Jan 1, 1956

By N. A. Gokcen, S. Fujishiro

THE pressures of Mn(g) in equilibrium with Mn7C3 and graphite have been measured by McCabe and Hudson' and Butler, McCabe, and paxton2 by means of graphite, zirconia, and Ta-Mo Knudsen cells. The details of corrections in their measurements were somewhat different from those of the authors;3'4 hence, further independent results at higher temperatures seemed to be warranted. The stoichiom-etry of Mn7C3 in equilibrium with graphite and its stability up to the vicinity of 1373 °K have been satisfactorily established by Kuo and persson5 (See also Hansen and Anderko).' The method of investigation has been described elsewhere in detail.3'4 The carbide was prepared in the manner described by McCabe and Hudson. In order to avoid possible reactions with refractory oxides, only graphite cells were used for the effusion experiments. The authors' results are the runs M-1, M-2 and M-3 listed in Table I, together with those of McCabe and co-workers. The heat capacity, c;, of Mn7C3 is not known; therefore McCable et al. plotted their data as log P vs 1/T and the results were only expressed first' as, and later2 as logP=- -14220+6.06 without further thermodynamic calculations. However, it is possible to estimate closely the necessary heat capacity as follows: When H; - &98 of CrC, or MnO, is plotted vs x, corresponding to various compounds, with temperature as the parameter, it is seen that the relationship is represented by a line of very small curvature. This relationship is also followed by other compounds which do not exhibit solid state phase transformations. In view of the fact that chromium and manganese have the atomic numbers of 24 and 25 respectively, it is reasonable to assume that H; - H;ae vs x for MnC, follows the same type of lines as those for CrC, for which adequate data are available.7 Similar correlations appear to be valid for oxides of two neighboring metals for which reliable data are available. The procedure is thus to move the lines for CrC, vertically (parallel to the axis of HT - H298) until they coincide with the points for MnC1/3, the only carbide of manganese whose H; - HO298 has been

Jan 1, 1963