Search Documents

By R. P. Rothwell

AT this our first meeting I beg to call the attention of the members of our Institute to what is certainly a question of the greatest possible importance to the industries we represent; and more particularly to the welfare of the coal and iron trades: I refer to the enormous waste of coal in mining and in its preparation for market, as now practised in our anthracite coal-fields. I t is a fact which many of you can certify to, that we are wasting fully me-half of all the coal in the veins we are now working, and there are cases, which might be mentioned where this proportion, immense as it is, has been greatly exceeded. The popular belief that our deposits of anthracite coal are "practically inexhaustible," is very far from being founded on facts. On the contrary, supposing the present rate of increase in the production to be maintained, it is probable that a maximum yield for our coal-fields would be attained in about fifteen years ; there are in fact some of our smaller basins where the principal veins are nearly exhausted and the production has already attained its maximum. There are others, again, where the depth attained-and it must be borne in mind that we commenced working at the surface outcrop moderate though it is (scarcely ever reaching eight hundred feet), has so increased the cost of mining as to imperil the capital invested, and though it requires but little foresight to predict the time when the difficulties of mining will be very considerably increased by reason of the greater depth, greater quantity of water, fire-damp, and other fruitful sources of cost, yet, ignoring these recognized facts, we continue to waste more than one-half of the coal where it is obtained with the least danger, expense, and trouble, that is, near the surface-either above water-level or at a moderate depth . below it. The inspection of almost any accurate mine map will satisfy you that, on an average, we leave fully one-third. of the coal in the ground as pillars to support the roof; in some places more than one-third thus remains, while it is very rare that less than one quarter is left. In almost every case this coal is absolutely lost, for it will very rarely pay to reopen gangways and lay roads to it after that portion of the mine has been abandoned. Is it necessary in all cases to support the roof, and where it is, may not some artificial

By Clarence Zener

The internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites, localized weak regions introduced by cold-working,6'7 grain boundaries and possibly twinning planes.8'9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3.i in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff. Experimental Method The experimental method used has previously been described in institute papers.5'6'9 The measure of internal friction adopted here, I/Q, is X the logarithmic decre- ment, a measure used by some writers, and is also X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. Experimental Results The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. I, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of 100 during the next Ioo° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e-H/RT [I]

Jan 1, 1943

By W. McA. Johnson

The work of J. E. Johnson, Jr., on the effect of small amounts of oxygen in cast iron in increasing its strength and resistance to shock, is of interest from the technical and scientific standpoints. The following exposition of the theory carries Mr. Johnson's explanation further and, in my opinion, will disclose certain related phenomena and perhaps shed further light on the subject. Some facts, so novel in character as to excite incredulity, have been accepted finally by many metallurgical authorities. One of these is that oxygen to the amount of 0.060 per cent. in cast iron gives it a breaking strength of 3,500 Ib. per square inch, compared with a breaking strength of 2,500 lb. per square inch in cast iron of the same composition with respect to elements other than oxygen, but having only 0.010 per cent, oxygen. The "oxygenated" cast iron, even if made in a coke furnace, has properties equivalent to the best charcoal pig iron. Mr. Johnson has also established the fact that the variations in combined carbon cannot account for the results. By microphotographic evidence he has shown that in oxygenated cast iron the graphite particles are dense and spherical, while in well-deoxidized cast iron the graphite particles are flaky and leaf-like. It is just a matter of common sense that iron of the latter structure is much weaker than the former. The analytical and microscopical work has been done with care and there is no doubt in my mind about the accuracy of the experimental results. In this paper then, we shall consider it as accepted that small amounts (0.060 per cent.) of oxygen increase the strength of cast iron by producing a structure in which the round and solid particles of graphite are surrounded firmly by a principal matrix of ferrite. The purpose of this paper is to show that the reason why the graphite particles are round is founded on the fact that the particles of any precipitate are made denser and harder by the presence of a reagent having a solvent action on the precipitate. This can be stated as a law, although I have never seen it so given in any textbook. Let us then, for purposes of illustration, give a concrete example and develop the theory of such mechanical and chemical actions as occur: It is well known that, by a soluble sulphate, a barium salt in solution is precipitated in a dense and easily filtered body when the solution is

Jan 1, 1916

By John A. Church

IN the year 1874, when the price of pig-iron was still high, that staple product became the subject of discussion in the newspapers and among those philosophers who are determined to know the "reason why" for all things. The object of the inquiry was to find out why iron did not fall in price as much as some other things had fallen. Indeed, there seemed to be an impression that iron and gold ought to move on nearly parallel lines, for the fact was constantly brought forward that iron then cost twice as much as it did before the war, though gold had returned to within twelve or fifteen per cent. of its former value. After some time the papers, by what seemed to be nearly unanimous consent, reached the conclusion that the maintenance of high prices was the work of the furnace proprietors, who, as the result of their shrewdness, were pocketing enormous profits. No proof was given to support this opinion, and the figures of cost and sale that were produced were of the most general kind, and used in the most vague manner. Visiting the president of the Thomas Iron Company, whose great works at Hokendaqua and Catasauqua, in Pennsylvania, are so well known as the largest and among the best conducted in America, I found him quite willing to meet the vague suspicions of the newspaper wiseacres, by a publication of the figures contained in the furnace-books of his company. These were accordingly given to the world through the Engineering and Mining Journal, and attracted the general attention they so well deserve. Though my own name became connected with these statistics, from the fact that I used them as the basis for the first attempt ever made to calculate the furnace economy of an American works, I can, without the suspicion of egotism, say that the statistics referred to are the most valuable contribution the literature of American blast-furnace work has yet received, for their interest is independent of personal considerations, and due entirely to the fact that they represent faithfully the details of practice in one of the most prominent American works. They are an exact transcript of the furnace-books, and form a body of accurate information of the greatest value to the metallurgical student. Their importance is shown by the fact that though the theoretical conclusions which I based upon them have been several times attacked, not one of my critics has made the slightest contribution to

Jan 1, 1876

By John Henry Harden

IN 1874, with Mr. H. Y. Attrill, of Baltimore, Md., I made an examination of some property at Goderich with reference to sinking for and mining salt. With this end in view we visited all the wells in the neighborhood, but the information sought being of so unreliable a character I advised the putting down of a borehole on the property. This has since been done, the result of which has lately been published by Dr. T. Sterry Hunt in the Toronto Globe. From this there appears to have been passed through six beds of salt of an aggregate thickness of 123 feet. Rock-salt was known to exist, for, by the boring of existing wells, small crystals had been brought to the surface in the dirt, but no attempt had before been made to obtain a reliable sample or to prove the number and thickness of the beds. The question now remaining for discussion is, shall the present method of obtaining the salt be continued, or shall the beds be won by a shaft in a regular mining fashion, by which means the salt may be gotten in a condition almost ready for the market? The present mode of obtaining salt is by boreholes from 6 inches to 8 inches in diameter drilled to the beds, into which is inserted a pump. The "feeders" of fresh water intersected in drilling the well are allowed to descend on the outside of the pump-tube to the salt beds and there become saturated, when, on use of the pump, brine is obtained for evaporation. In the beginning brine can only be had in limited quantity, but by the daily application of the pump, and the gradual solution of the salt, a larger surface becomes exposed to the action of the fresh water, and a continuous supply of brine is obtained. It will then be understood that the supply of brine is dependent upon the feeders of fresh water intersected in boring the well, which, we are told, have never shown any sign of diminution, and this is the water that must be encountered in sinking a shaft. There are ten wells in operation at Goderich, the most important one to the present project being known as the Hawley Well, located at an elevation a few feet above Lake Huron at the mouth of the river Maitland, at a much lower level and nearer to the proposed shaft than any other well in the district. At this well the feeders

Jan 1, 1877

By John L. Baum

Tests show that 50 times the earth's normal field can exist near stacked drill rods. Protection against the effect of these strong fields can be obtained by means of a removable sleeve of common iron pipe. GEOLOGISTS and engineers working around a diamond drill rig have often had the opportunity to observe the magnetic attraction of drill rods pulled out of the hole for core removal. This is sometimes an amusing pastime, but this same magnetic force inadvertently applied to a compass needle can cause it to lose its polarity entirely or to become reverse polarized when placed in the immediate vicinity of stacked rods. The first recommendation, of course, would be to avoid the rods, but in surveying an operating drillhole this is not always possible; therefore steps must be taken to neutralize the magnetic effect of the drill rods. Early in the summer of 1949 the geological department of the New Jersey Zinc Co. undertook at Franklin, N. J., an extensive program of surveying the course of deep diamond drillholes. The majority of the holes were surveyed while in the process of being drilled, and considerable difficulty was encountered. A pattern for the deviation of drillholes had been established for the district from surveys in holes from which the drill rig had been removed. It was observed that a certain operating deep drillhole being surveyed did not fit this pattern. In the resulting confusion of repeated surveys and cementing a plug for wedging operations, the lower 1800 ft of the hole was lost. Because of this incident studies were initiated to determine the source of the difficulties and to develop safeguards against recurrence of faulty surveys. Using a hand magnet easily shows that the polarity of a compass needle can be reversed if rotation of the needle is hindered through tilting of the compass or clamping of the mechanism. Such experiments are not recommended, especially in the case of the clockwork type of instruments. A magnetized hairspring in a clockwork instrument will cause the compass card to assume a periodic motion which will not stop until the clockwork runs down. Routine check readings of instrument north before and after each survey are not always sufficient to catch instances of reversed polarity of the compass needle. Although the majority of instances probably take place while the instrument is being removed from the hole with needle in fixed position, it is demonstrable that a 'luggish needle, weakened during a previous test, can be reverse polarized

Jan 1, 1955

By H. L. Talbot, R. S. Young, A. Golledge

The differentiation of oxidized forms of lead from lead sulphide in complex products by chemical analysis is of considerable importance to certain mining and metallurgical companies. A method for the separation of "oxide" lead, (non-sulphide), from sulphide lead, based on the solubility of the former and virtual insolubility of the latter in concentrated ammonium acetate solution, has been employed for many years in the industry.1,2 Unfortunately this solvent, while satisfactory for lead sulphate and carbonate, is without action on lead phosphates or vanadates, with the result that at .Rhodesia Broken Hill Development Co. where these latter minerals are present, they have counted as sulphides when using this procedure. For the control of operations in the new concentrator it became necessary to have a closer check on sulphide lead than could be obtained by the only current method of differentiating this constituent from oxidized lead. For some time this problem has engaged our attention, and after a large number of solvents had been tried, the following procedure was evolved. Like all methods depending on selective solution in a com- plex material, it will not give 100 pct separation into oxide and sulphide portions. Because of the ease of oxidation of galena this is almost an impossibility. Our procedure will, however, give a recovery of 99-100 pct of the oxidized lead, contaminated with very small quantities of lead sulphide, and a corresponding recovery of 97-98 pct of the sulphide lead. The procedure is simple and reproducible, and gives results quite .satisfactory for routine control purposes. Experimental For this work standard samples of the following pure lead minerals were obtained from Broken Hill, Northern Rhodesia. These were hand-picked specimens, and were carefully ground to —200 mesh. Since it was realized that a fair-sized sample would be necessary for this work to thoroughly test the large number of procedures we had in mind, a compromise had to be effected between a few grams of very pure minerals and a large sample of lower grade material. For this work the presence of gangue was not deleterious, so long as the oxide lead minerals did not contain lead sulphide, and vice versa. Table I shows the lead minerals used, and their total lead content, both theoretical and actual. Apart from the pyro-morphite the minerals are seen by analysis to be quite pure. Many solutions were tried in an effort to dissolve the oxidized lead minerals and

Jan 1, 1949

By Woolsey Johnson

THE object of this paper is to, describe the several necessary characteristics of the zinc-retorting charge and to show how by certain improved methods; the large excess of coal, over that theoretically required, can be reduced, thereby effecting an increase in the smelting capacity of a retort plant as well as other economies. In the Southwestern zinc works a charge of roasted zinc ore with a side mixture of carbonates and silicates, analyzing on the average 50 per cent. Zn, is mixed with 55 or more per cent. of its weight of a mixture of coal and coke analyzing 60 to 70 per cent. fixed carbon. . The ore is of varying fineness and the coal and coke are usually crushed in a semi-moist condition through a 3/8 -in. screen. With ores of a slaggy nature, this coal proportion is increased, sometimes to as much as 100 per cent. of, the weight of the ore. With carbonate ores, or where anthracite screenings with higher carbon content are cheap enough, the percentage of reducing agent is cut to 45 per cent. or even somewhat lower. The average charge per retort for a monthly run of a plant on ore, as distinguished from retorts on blue-powder, ladle-skimmings and other between-products, runs from 60 to 66 lb., with a mean of 63 lb. for the Southwest with standard retorts of 8 ½ -in. inside diameter and 50 in. long inside, using roasted sulphide ores. Conditions will change these figures, but 40 lb. of ore per cubic foot of retort space is, I believe, an average in the better-operated plants. Since the rise in. the price of spelter, the tendency has been to overcharge. To remove the slag that is formed when retorts are overcharged, extra men are put on to "gum-chisel" the retorts to prevent "set" furnaces and "butchered, retorts." Taking the above conditions as premises, we find that from four to six times the amount of coal necessary for the reduction is used, as is evidenced by the fact that the residues analyze as high as 35 per cent, fixed carbon. There are good reasons why this excess of fixed carbon must be used and perhaps these can be best explained by a description of the metallurgical requisites of a zinc charge. We may enumerate these as follows: 1. High reducing power, especially at the end f the shift, to reduce any carbon dioxide to monoxide and bring about a good condensation

Jan 2, 1918

By Edmund C. Pechin

I REGRET that I am unable to present this subject in definite form and detail. All I shall attempt at this meeting is to lay before you some curious facts, the bearings and explanations of which must be reserved for future consideration. I hope before the next meeting to have carried experiments far enough to furnish a more important contribution to the science of iron metallurgy. The Wickersham process consists in the introduction into the molten metal, as it runs from the furnace, of air from the hot blast. Mr. Samuel Wickersham is the originator of the plan, as applied in practice, although Mr. Martien had the idea a long time ago, and, I believe, .went to England about it. But at that time Mr. Bessemer was coming before the public with his invention, which engrossed the attention of iron-masters, and Mr. Martien accomplished nothing. The principal difficulty in our experiments at Dunbar was to get a practicable runner or trough, through which the molten metal should pass, and in which it should be exposed to the action of the blast. The runner we used was ten feet long, and perforated on the sides to permit the entrance of the air-currents. When we used a cast-iron and fire-clay runner, the heat was so great that before we were more than half done with a run, the lower part of the runner was melted, and we had a magnificent Fourth of July display of fireworks until the blast was shut off. We had to abandon fire clay. The runner with which we have had the best success ,is made of wrought-iron tubes, 2 1/2 inches in diameter, attached to a wrought-iron frame, and lined with a mixture of crushed conglomerate (quartz) and a little fire clay to give it cohesion. The wrought-iron shell curves inward over the upper edges, so as to catch and throw back into the current the flying sparks and particles of metal thrown out by ebullition. With this we have been able to run 12 to 14 tons at a heat with great ease. Mr. Wickersham has since prepared this material (pounded quartz) into a shaped brick or tile, with the necessary perforations for the passage of the air, which promises to answer every requirement for steady working. As regards the improvement in the quality of the iron, there seems to be no question. A large number of practical tests were made in

Jan 1, 1873

By Allen Rogers

TWENTY-FIVE DOLLARS for nothing at all except a sheepskin. That to me is the effect of the New York State law for registration of engineers and the same may be said of any of the state licensing laws. Of course, if one has to practice in more than one state, he must pay a more or less equal amount for every state he works in; and yet there has been little effective protest against these laws. It would seem that the spirit which animated the Boston Tea Party is non-existent amongst engineers. Undoubtedly a good many consider, through their failure to understand the law, that the matter does not affect them. In New York State it is provided that "any person practicing or offering to practice profes-sional engineering or land surveying . . . shall be licensed as hereinafter provided." To quote further from the law: "A person practices professional engi-neering . . . who holds himself out as able to do, or who does, the work that an engineer does . . . " The cunning of the wording of this article can only be appreciated by considering that anyone calling himself an engineer falls within the definition; its liberal inter-pretation (I have not quoted the whole of it) would embrace many who do not consider themselves engi-neers. The state authorities may not construe it to include such individuals; indeed, they may possibly consider it inexpedient to extend it to include engineers of subordinate grade, but the possibility is always there and, even though an engineer be of the grade of assis-tant, he may at any time be called upon to substitute for his principal in responsible charge of the work. It is therefore clear that anyone calling himself engineer and practicing engineering must, for his own protection, apply for registration or run the risk of violating the law. Now, what is the sense of all this? We have done very well without such restrictions on the means of gaining our livelihood. If one only stops to think, there is hardly a minute of his modern existence when he is not dependent for his safety on the engineering by engineers of yesterday or today. How often is one in jeopardy through failure of engineering works, work done under the supervision of those same engineers? If all of us had to wait for our ends by such means, our average life would probably be some thousands of years. Where, then, is the point to the object declared in all these laws that the need for licensing is "to safeguard life, health and property?" Bosh!

Jan 4, 1923

By C. J. Fleisch, C. P. Clingerman

THE recent installation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. THE FURNACE PROPER A few of the characteristic points and dimensions of the furnace proper are: [Hearth diameter 26 ft. o in. Bosh diameter 29 ft. 1 3/4 in. Stock-line diameter 20 ft. o in. Large-bell diameter 114 ft. 8 in. Small-bell diameter 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed 94 ft. 4 in. Height of furnace from center of iron notch to main platform 105 ft. o in.] The furnace top is equipped with a McKee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. g in. in diameter, then through uptakes that are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. DUST CATCHER The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catcher is g ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is 50° with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas in-

Jan 1, 1943

By Leonard D. Jaffe, Donald C. Buffum

THE importance of temper brittleness in alloy steels has long been realized in Europe, In the United States recognition of its importance has developed within the last several years. Many brittle failures encountered in parts made of alloy steel are undoubtedly attributable, wholly or in part, to temper brittleness. These failures have occurred particularly at low temperatures, under shock loading, and in the presence of notches, restraints and combined stresses. It has been almost universally accepted that plain carbon steels are not susceptible to temper brittleness. As a result, considerable effort has been expended in attempts to discover the manner in which alloying elements introduce temper brittleness. It is desired to raise the possibility that plain carbon steels are not only susceptible to temper brittleness, but are much more susceptible than alloy steels, in the sense that they embrittle much more rapidly. It is suggested that previous views, (that plain carbon steels are not susceptible), are based upon an erroneous interpretation of the experimental results. INTERPRETATION OF PREVIOUS DATA For many years the standard criterion for susceptibility of a steel to temper brittleness consisted of comparison of the energy absorption, in a notched-bar impact test at room temperature, of specimens that had received two heat treatments.1 One specimen (or group of specimens) was quenched, tempered, and quenched from the temper. The other specimen (or group) differed only in having received an embrittlement treatment, which might consist of a slow cool from the tempering temperature, or of an isothermal hold in the range 450-550°C subsequent to quenching from the temper. If the energy absorption of the specimen receiving the embrittlement treatment was lower than that of the specimen not given this treatment, it was said that the steel was susceptible to temper brittleness, If the energy absorptions were the same, it was said that the steel was not susceptible. Several investigators2,3 found that plain carbon steels showed negligible difference in energy absorption in such tests (at least when their manganese content was below 0.60 pct), and concluded that plain carbon steels are not susceptible to temper brittleness. Recently the deficiencies of the criterion mentioned above have been pointed out.4-6 The criterion now generally used for susceptibility to temper brittleness retains the heat treatments used in the earlier scheme, but instead of the notched-bar impact tests being made only at room temperature, they are made over a range of temperatures, covering the transition from ductile to brittle fracture, If the transition temperature of the specimens receiving the embrittlement treatment is higher than those

Jan 1, 1948

By B. Silliman

The experiments detailed by Dr. Hunt,* having demonstrated the fact that the copper contained in the "clay ore" of Jones's Mine, was rendered completely soluble in the bath of ferrous chloride, used in the Hunt and Douglas process, after heating in contact with carbonaceous matter in a close vessel, I set myself to devise a form of muffle furnace adapted to the treatment of large quantities of these and similar ores by a continuous process. The result is shown in the diagrams on Plate X, reduced from the working drawings, after which this furnace was built early in 1876, at Phœnixville, by the Chemical Copper Company on their works at this place. The peculiar character of this ore determined the form, dimensions, and position, with reference to charging and discharging of these muffles. The ore arrived from the mine with from 20 to 25 per cent. of moisture, and when dried at 21o F., or more slowly at lower temperature, it falls to a light incoherent powder, with occasional lumps of undecomposed rock. In this condition it is readily mingled with coal-dust or any like reducing agent, and requires no other preparation for the muffle than the use of the shovel, to mix it well with the reducing agent. As it is a remarkably good non-conductor of heat, it was obvious that the mass, to be heated through in a reasonable time, must not be too thick, while the weight of the mass must be sustained in a way to avoid undue strain upon the walls of the muffle. These walls must be as thin as practicable, to favor the more rapid transmission of heat, and must, therefore, be so constructed as to admit of being stayed on the sides at frequent intervals to resist the lateral thrust of the very mobile mass of pulverulent ore, which, for obvious reasons, must be charged at the top and drawn from the bottom of each chamber. These considerations led to the form adopted, viz., two vertical muffles, standing upon very strong bridge tiles, seen in longitudinal section, on the line E, F, and in plan in Fig. 3, on the same plane. (Plate X.) The vertical section of the muffle is seen in Fig. 4, drawn in the plane G, H, of the longitudinal section, Fig. 6, which is the key to all sections. The walls of the muffles are built of the best firebrick, very care-

SULPHUR is a very well known mineral and apparently is produced in many places. It is engendered from an unctuous earthy and powerfully hot substance so that it is considered among experienced workers to bear a resemblance to the element of fire. This is called by these same men the masculine seed and the prime agent of Nature in the composition of metals. Because of its great dryness and heat it has, as experience shows, affinity with fire, which is easily introduced in it when brought near. And once introduced the fire is quenched only with difficulty before its unctuousness is wholly consumed. Although it shows itself to us of such a hot and dry nature, we must not think that sulphur is a substance so pure that it can stand by itself or that in order to attain its form it has no need of its portion and part of moisture like every other mixture. This is shown to us by its easy fusion, in which it resembles the metals. This thing is found in many places and in many varieties of color; some are white, others yellow and orange, and some others between gray and black. They also say that some red is found. It does not occur in that arrangement of veins like other minerals, but most liberal Nature makes whole mountains of it as is seen in the Aeolian islands, [26] near Sicily, in Etna or Moncibello which is the island of Sicily, at Pozzuoli, in the territory of Rome, in the Sienese domain at San Filippo, and in many other similar places. It is a substance that has a very strong odor and is most unpleasant to smell. It is very fixed in its substance so that it is never corrupted by time, by boiling, or by the moisture of water. For although it may stand in water a long time it never becomes soft nor does it ever decrease or increase in weight. It is brittle and easily crushed very fine. It is said that a trace of garlic rubbed on the mortar helps anyone who wishes to reduce it to impalpability. Its ores have a form more like earth than like stone although they some¬times have the color of a certain soft rock. The places where it is found are easily recognized by the great odor that they give out and by the very hot baths that often spring forth near it. What I have already told you about quicksilver that is contrary to the

Jan 1, 1942

By W. R. Jones

composition, he cannot reasonably asl; the manufacturer to guarantee that this composition shall give certain physical results. W. R. Jones, Pittsburgh, Pa. : The question that naturally occlun to me is this: Has Dr. Dudley in his inveatigtrtions been aiming to prove a theory, or has he been guided by an earnest desire to discover what are the proper elements in the composition of a good-wearing steel rail ? Unfortunately, for correct chemical information, he has omitted in his analgw two very importnat elements,—sulpbur and copper. Now, before we will even begin to admit the correctnets of Dr. Dudley's conclusions and the formula he prescribes, we will at the start question the propriety of any chenlist or scientist prescribing a formula for making steel when he has iguared such important ele ments as sulphur aud copper. I, for one, will not accept any such formula. Are we sure, or is Dr. Daclley sure, that the chemical analyseq embodied in his paper are correct? This may seem a presumptuous queetion, yet, with my experience with chenlists, I naturally doubt the correctness of the analyse8, and, before I will accept them as correct, I will ask that comparative tests of phosphorous and man ganese be made by the Pennsylvania Railroad chemists and the chemists of the leading steel-works in the country. Let us first verify the correctness of the analyses before we consider the con clusions. I can enumerate a great number of instances in which chemists have differed very widely in their determinations of phos phorus and manganese. A prominent iron fitam made a contract with the Edgar Thomson Steel Company to deliver pig metal guar anteed to be between 0.07 and 0.08 phosphorus; an analysis by our chemist resulted in phosphorus 0.148 and 0.152,—a rather startling difference! Again, a sample bar of steel, in which our chemist reported phosphorus 0.11, was tested by a chemist of au other Bessemer works, ana his determinations were phosphorus between 0.07 and 0.08: A leading engineering establishmeut of Pittsbdrgh bought iron claimed by a chemical analysis to contain 0.08 phosphorus; our Mr. Ford found phosphorus 0.145. A chem ist connected with an open-hearth works reported manganese in a piece of steel, 1.14; in a second determination from the same piece of steel, by the same chemist, manganese was reported 0.43. The chemist was kept in ignorauce of the fact that both samples were from the saw piece of steel. Two dctermiuations for manganese

Jan 1, 1881

By Coopers &. Lybrand

INTRODUCTION From a tax viewpoint, United States mining companies are at a substantial disadvantage in the international mining area compared with companies in other major capital-exporting countries, according to a 1975 study by Coopers & Lybrand for the American Mining Congress. The study compared the relative tax position of a United States investor with investors from Belgium, Canada, France, Germany, Japan, the Netherlands, Switzerland, and the United Kingdom. The comparison was based on average rates of return realizable by investor companies on four mine-model investments in twelve capital-importing countries. The countries in which these investments were assumed to be made are varied in their tax systems so that a wide range of possibilities was included in the analyses. Each mine model was standard so that the rates of return for each investment by each investor were affected solely by the respective tax systems of the capital-exporting and capital-importing countries. UNITED STATES POSITION The study found that the United States competitive position, in terms of the average rate of return on an overall basis, ranked next to last among the nine capital-exporting countries in the study. Further, the United States overall rate of return is more than 20% below that of the country (Japan) with the highest overall rate of return. On an average return-on-equity basis, the United States' position among the nine investor countries, for each of the mine investments studied, was: copper, eighth; iron ore, sixth; nickel, fifth; manganese, a tie for last place. Figure 1 shows the overall results realized by each capital-exporting country on the basis of average return on equity. [ ] The frequency with which a given capital-exporting country attains the highest or next highest rate of return in a capital-importing country provides further insight and another basis for comparing the tax laws of the capital-exporting countries. Of the situations compared in the study, the United States never attained the highest rate of return, and reached the second and third highest rate of return in only two instances. The tables showing the frequencies of rankings are given in Table 1 for each of the four mine models. In summary, the United States mining company does not have a competitive advantage under the tax rules when competing for mineral concessions in other countries. The United States company, in fact, appears to be at a clear disadvantage. The study also considered the effect of the following recent tax proposals on United States investors in international mining ventures:

Jan 1, 1985

By John Henry Harden

IN 1874, with Mr. H. Y. Attrill, of Baltimore, Md., I made an examination of some property at Goderich with reference to sinking for and mining salt. With this end in view we visited all the wells in the neighborhood, but the information sought being of so unreliable a character I advised the putting down of a borehole on the property. This has since been done, the result of which has lately been published by Dr. T. Sterry Hunt in the Toronto Globe. From this there appears to have been passed through six beds of salt of an aggregate thickness of 125 feet. Rock-salt was known to exist, for, by the boring of existing wells, small crystals had been brought to the surface in the dirt, but no attempt had before been made to obtain a reliable sample or to prove the number and thickness of the beds. The question now remaining for discussion is, shall the present method of obtaining the salt be continued, or shall the beds be won by a shaft in a regular mining fashion, by which means the salt may be gotten in a condition almost ready for the market? The present mode of obtaining salt is by boreholes from 6 inches to 8 inches in diameter drilled to the beds, into which is inserted a pump. The "feeders" of fresh water intersected in drilling the well are allowed to descend on the outside of the pump-tube to the salt beds and there become saturated, when, on use of the pump, brine is obtained for evaporation. In the beginning brine can only be had in limited quantity, but by the daily application of the pump, and the gradual solution of the salt, a larger surface becomes exposed to the action of the fresh water, and a continuons supply of brine is obtained. It will then be understood that the supply of brine is dependent upon the feeders of fresh water intersected in boring the well, which, we are told, have never shown any sign of diminution, and this is the water that must be encountered in sinking a shaft. There are ten wells in operation at Goderich, the most important one to the present project being known as the Hawley Well, located at an elevation a few feet above Lake Huron at the mouth of the river Maitland, at, a much lower level and nearer to the proposed shaft than any other well in the district. At this well the feeders

By Carl E. Swartz

The Joint Session on Continuous Casting, of the Institute of Metals Division and the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers, convened in the Jade Room of the Hotel Waldorf-Astoria, New York City, on Feb. 23, 1944, at 9:15 o'clock, Carl E. Swartz presiding. C. E. SWartz.—It is gratifying to see so many out at what may seem an early hour for the beginning of A.I.M.E. sessions, but I think this number-—some fifty or sixty of you —is an adequate expression of the interest in these processes all over the United States, and possibly in foreign countries. I would like to ask those who feel that this type of program is of value to you to write or speak to some one of the Institute of Metals Division officers and suggest other topics for symposiums. We have a feeling that some of these current practices are of interest and we believe that under proper sponsorship many of the companies mill be willing to give publicity to processes such as those that will be discussed today. Also, we would like suggestions and criticisms, so that the next ones can be better. The subject of continuous casting is not new, of course. The two papers on the program this morning will adequately cover the history and some of the earlier processes, some of the theory and some of the practice, some of the reasons why these various methods did not work. I was rather interested in discovering, when thumbing through one of the A.I.M.E. publications tile other night, an article on continuous casting. I was not aware that the A.I.M.E. had published any papers on continuous casting, but there may be a number. The one that I happened to find was published in the 1915 volume, on the Mellen rod-casting process, and so we might say this is not the first session in which these subjects have been under discussion. However, there have been many improvements since then in all fields of metallurgical and mechanical engineering; consequently, I think that the papers today will be a little more involved and a little more complete in their technique. The first paper today will be given by one of our gentlemen of the press, who has done one of the outstanding jobs in this country in calling to our attention some of the newer processes that are being considered and being used in the metallurgical indus-

Jan 1, 1945

By J. B. Cheatham

The influence of friction on the force required for an idealized bit tooth to penetrate a "plastic" rock is analyzed. The rock is assumed to obey the Coulomb-Mobr yield criterion and the tooth is represented by a two-dimensional sharp wedge. At the tooth-rock interface the stress field not only satisfies the yield condition but also is such that the ratio of the shearing stress to the normal stress is equal to the coefficient of friction. The solution relates the force on the tooth to the depth of penetration, the tooth angle, the coefficient of friction between the rock and bit tooth and the angle of internal friction and compressive strength of the rock. INTRODUCTION Most rocks are brittle at atmospheric pressure but exhibit ductility and increased strength as the confining pressure is increased. In a previous analysisl the force required for a bit tooth to penetrate a rigid-plastic rock was computed for two limiting conditions: (1) a perfectly lubricated tooth-rock interface which should correspond to a lower limit for the penetrating force, and (2) a perfectly rough interface which should provide an upper limit. Experimental results2 for rock indentation under confining pressure have confirmed that the analysis generally predicts upper and lower limits for the penetrating force as a function of rock properties and tooth angle. The present analysis extends the previous work to account for the friction between the rock and the tooth. ANALYSIS The force required for incipient plastic flow of an idealized model of a rock under a bit tooth is computed subjected to the following assumptions. BIT TOOTH 1. sharp two-dimensional wedge (end effects neglected) 2. rigid tooth (elastic deformation of tooth neglected) 3. displacement of tooth is normal to rock surface 4. friction exists between tooth and rock ROCK 1. semi-infinite, isotropic and homogeneous 2. rigid-plastic (elastic deformation of rock neglected) 3. non-work hardening (horizontal stress-strain curve) 4. Coulomb yield condition* (linear Mohr envelope) 5. smooth, flat surface According to the Mohr theory of failure it is assumed that failure occurs when the state of stress is such that the Mohr stress circle becomes tangent to an experimentally determined envelope. The Mohr failure curve is frequent1y approximated by a straight line and referred to as the Coulomb-Mohr failure criterion. If the rock is under sufficient pressure to be ductile we can use the linear envelope as a yield condition. The Coulomb-Mohr yield criterion is illustrated by Fig. 1 and is expressed by the following equation:l

By W. P. Blake

FORGING under the hydraulic press, which was introduced by Haswell in the year 1861, at the machine shops of the Imperial State Railway Company of Austria, has since been greatly improved, so that at the present time there are very few parts of machines which cannot be produced in this way, and at no greater cost than iron castings. The process is now used at Vienna chiefly for such parts of locomotives as cross-heads, link-bars, axle-box frames, etc., especially where the form is intricate, and there are many angles and projections. These objects weigh from 50 to 150 lb. or more, and it is claimed for them that they are not only much cheaper than ordinary forgings, but are much more regular in form and stronger. The results which Mr. Haswell has attained, after years of patient experimenting, were well shown in the Austrian Department of the Vienna Exhibition by a collection of the pressed objects in iron and steel, just as they left the moulds, with some of them cut asunder longitudinally and the surfaces etched, so as to show the internal structure or direction of the grain. Through the courtesy of Mr. Haswell and his son I saw the hydraulic presses in full operation at the works, drawing down large Bessemer ingots, cutting them up into blocks of convenient size, and forming various parts of locomotives. They have two large hydraulic presses in use; the largest, with a piston 24 inches diameter, gives 1200 tons pressure, and the second, with an 18-inch piston, gives 600 tons pressure. The pressure in the pumps is 600 atmospheres. The action is vertical ; the piston descends upon the work, and for forging ingots is armed with a hammer-like head. An ingot of No. 7 soft Bessemer steel, which was forged in my presence, weighed 2030 lbs. One end being placed upon the anvil, the piston is brought slowly down and crowded into the mass as if it were putty or dough, forcing it each way, but chiefly in the direction of the length of the ingot, this being the narrowest section of the anvil and hammer. The piston is then raised and the ingot is moved forward for a second squeeze, and so on, until the first half of the ingot has been reduced in thickness, when it is turned on edge and the operation is repeated. The ingot is then turned end for end and forged until the whole length has been re-

Jan 1, 1874