Search Documents

By W. A. Ver Wiebe

UNder the impetus of new demands caused by the defense program, the oil and gas industries of Kansas established new records during the year 1941. In all, 2113 wells were drilled, which compares favorably with the record total drilled in 1937. These 2113 tests resulted in 1446 oil wells, 76 gas wells and 592 dry holes. In all three categories there was an increase over the previous year, but unfortunately the most marked increase was in the dry holes. Nearly 80 per cent of the increase must be allocated to the drilling 01 unsuccessful tests. This was partly because of the increasing difficulty of finding new reserve areas and partly because of the erratic character of the production in the Arbuckle dolomite, which is now the main producing zone. Closer analysis of the totals reveals that western Kansas accounted for 1634 tests, of which 1186 were oil wells, 34 were gas wells and 415 were dry holes. The total potential initial daily production uncovered by the successful wells amounted to 1,691,000 bbl. of oil and 508,000,000 cu. ft. of gas. Both figures indicate a considerable decrease when compared with the proceeding year; in 1940 the respective figures were 2,128,000 bbl. and 1,289,000,000 cu. feet. In eastern Kansas a total of 479 wells were drilled. Among these, 260 were oil wells accounting for a daily initial potential production of 45,662 bbl. The new gas wells numbered 42 and added 290,438,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 177 in number, were dry. It is interesting and significant that almost half (791) of the total wells drilled in western Kansas were drilled by the independent operators. Among the large companies the Cities Service Oil Co. drilled 169 wells; the Stanolind Oil and Gas CO., 101; the Skelly Oil Co., 80; the Continental Oil Co., 99, and the Shell Petroleum Co., 63 wells. In eastern Kansas the independent operators drilled 406 out of the total of 479 wells. Among the major oil companies the Cities Service Oil Co. drilled 38; the Phillips Petroleum Co., 13, and the Sinclair-Prairie Oil Co., II wells. The figures on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas approximately one third of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 844 wells in western Kansas, of which 678 were successful in finding either oil or gas. It thus appears that the major companies fared much Getter than the independents. In eastern Kansas the major companies drilled 73 wells of which 63 were successful in finding commercial quantities of oil or gas. No less than 286 wildcat tests were put down in western Kansas and 72 in eastern Kansas, or 358 in all, during 1941. Considerably more than half of these were drilled by independent operators; zoo in western and 66 in eastern Kansas. An exploratory hole % mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, approximately 75 per cent of all wildcat wells were failures; only 25 per cent found oil or gas in western

Jan 1, 1942

By W. D. Robertson, A. S. Tetelman

The technique of decorating dislocations was employed to investigate deformation and fracture resulting from Precipitation of hydrogen in Fe-3 pet Si single crystals. It is shown that cracks are produced on (100) planes inside crystals, as a consequence of the precipitation of hydrogen gas, either when crystals are quenched from a hydrogen atmosphere at elevated temperatures or cathodically charged with hydrogen at room temperature. Plastic deformation in the vicinity of cracks, observed as arrays of decorated dislocations, is in conformity with the calculated stress distribution about a crack containing an internal pressure, and the observations provide information permitting a detailed analysis of the mechanics of crack growth. The fracture characteristics of crystals containing internal cracks were evaluated at 25o and -196°C and the results are related to the mechanism of hydrogen embrittlement in terms of the growth of preexisting cracks. HYDROGEN in bee iron or steel produces two characteristic changes in mechanical properties: I), a decrease in ductility (macroscopic strain at fracture) that depends on temperature and strain rate, and 2), spontaneous fracture under static load that depends on time and apparent stress. Resolution of these phenomena into the microscopic processes that combine to produce the macroscopic effects is especially difficult in the Fe-H system in which the active component cannot be directly observed and only maintained in equilibrium with great difficulty in the temperature and pressure range in which embrittlement phenomena appear. As a result of these complications, verification of the numerous hypotheses'-5 that have been proposed to explain the microscopic mechanism of embrittlement depends on self-consistency with measured changes in macroscopic properties that are averaged over the volume of a specimen. It is obviously important to obtain a more direct evaluation of the microscopic processes that combine to produce embrittlement. Accordingly, the present investigation was designed to identify and observe, as directly as possible, the microscopic effects of introducting hydrogen into a bee crystal. It was concluded from a previous investigation6 of X-ray line broadening, produced by introducing hydrogen into pure iron at room temperature, that the only effect that could be associated with the introduction of hydrogen was plastic deformation; in particular, dilation of the lattice was not observed, within ± 0.01 pet, and no evidence was found that could be interpreted to support the idea7'* that hydrogen occupies tetrahedral interstitial sites in the iron lattice. The absence of lattice dilation is consistent with the extremely small solubility of hydrogen in bee iron9,10 (0.015 at. pet at 900oC and 1 atm pressure), and the evidence of plastic deformation is consistent with the fact that hydrogen, introduced by cathodic charging, eliminates the carbon yield point.11-13 Following this investigation, the immediate problem was to devise a method by which plastic deformation could be observed directly. The technique employed by Hibbard and Dunn14 to observe the movement of dislocations during bending and subsequent polygonization of Fe-3 pet Si single crystals was adopted and modified for the present purpose to include the observation of dislocation arrays in the volume of the crystal, and their association with the fracture process. EXPERIMENTAL PROCEDURE Single crystals of a high purity Fe-3 pet Si alloy, containing 0.007 pet C, were grown in vacuum by

Jan 1, 1962

air-lift and equipped with tapered tubing of proper design, we would have a gas input consumption of about 2500 cu. ft. per bbl., which at 3 to 4c. per 1000 cu. ft. would be 7 1/2 to l0c, per bbl., and there would be very infrequent loss of production due to stoppages. It has been demonstrated that with efficient design of air-gas lift, the production of wells can be increased much beyond that obtained with the former type of air-lift employed; also that small wells can be operated by air-lift with tapered tubing at a cost that places this method in competition with beam pumps in many fields. The next step in conservation that the writer expects to have an opportunity to demonstrate is that of restoring the pressure in a pool and producing by air-gas lift all of the oil possible to lift economically. This combined operation is probably the method toward which we shall eventually be working in recovering the maximum quantity of oil from pools where the oil is recovered through bore holes. General Discussion on the Air-gas Lift H. P. Porter, Tulsa, 0kla.—The papers presented at this meeting contain a great amount of valuable information. Wonderful progress has been shown in the development of air and gas-lifts. There has been nearly everything brought out that touches upon the subject. The real point that is lacking is exact knowledge of the velocity with in the flow column which will produce the best effect—that is the thing we must know more about. Velocity in Gas-lift Flow In other lines of industry the matter of velocity of fluids in pipe lines has been well analyzed and there are known laws by which to calculate velocity of flow; for instance, in irrigation work large pumps are designed with intake pipos to employ an intake velocity of 4 ft. per scc. By reduced cross-sect'ion the velocity is increased rapidly as it enters the pump and the discharge rate is at 12 ft. per src., which in turn is reduced in the discharge column to 4 ft. per sec. Crushed coal, grain and granular material is found to be best conveyed by air when a pneumatic conveyor is employed at 100 ft. per sec. As in the design of a pumping plant or a pneumatic conveyor, the velocity at the lower end of the column in the flowing well must be controlled within certain limits for best results. Mr. Griswold, I believe, stated that they had velocity as low as 15 it. per scc. and from that up to 78 ft. per sec. Mr. Pierce and Mr. Lewis showed an ideal flow column showing how the velocity increased as the fluid was carried up the column, hut did not give any figures as to the velocity. It would be well to take that sort of a diagram to establish an ideal velocity at the lower or intake end, and then calculate the velocity from expansion of the gas as it goes up. It may be that the, ideal intake velocity would vary, depending on the depth of the well, the quantity of liquid to be handled or the pressure which it may be desired to hold. The subject is one that might be worth much research.

Jan 1, 1928

By B. Wilhelmi, W. H. Somerton

Simultaneous measurement of pore and elastic properties of socks under a wide range of triaxial stress conditions may be made with equipment and methods developed in this paper. Tests were run on three outcrop sandstones at several confining pressures and axial stresses up to approximately 80 percent of failure stress. The greater reduction in porosities and permeabilities occurred in the hydrostatic loading portion of the stress cycle, but substantial reductions in both properties did occur upon application of deviator (triaxial) stress. Triaxial elastic moduli were calculated from strain gauge measurements. Both Young's moduli and shear moduli were found to increase with increasing confining pressure. Poisson's ratios increased with axial stress but showed no consistent change with confining pressure. Only very general relations were observed between pore and elastic properties. The lesser decrease in porosity and permeability at higher stress values is related to increase in rigidity of rocks at higher stresses. INTRODUCTION Many investigators have studied the effects of hydrostatic stress on the properties and behavior of rocks. A few have studied the effects of triaxial stress fields on individual physical properties of rocks. To our knowledge no one has measured simultaneously pore and elastic properties of rocks under a wide range of triaxial stress conditions. This is the purpose of this work. Rocks exist in the subsurface under what Jaegerl refers to as "polyaxial" stress conditions (all principal stresses unequal). When two of the three principal stresses are equal, this is referred to as triaxial loading. The triaxial method of loading is most commonly used in modern testing work because experimental difficulties in measuring physical properties of rocks are greatly reduced over polyaxial testing. Although triaxial loading may not reproduce subsurface conditions precisely, subsurface stress conditions are never known precisely anyway. Triaxial testing would seem to be more realistic than testing under hydrostatic loading (all principal stresses equal) for application of results to subsurface problems. The objectives of this work were threefold: (1) to develop methods of measuring simultaneously pore and elastic properties of rocks under triaxial stress conditions, (2) to determine whether changes in these properties are of sufficient magnitude to be considered in subsurface calculations and (3) to attempt to relate changes in pore properties and elastic properties since they will have been measured at the same time under identical loading conditions. REVIEW OF EARLIER WORK PORE PROPERTIES Several investigators have studied the effects of stress on the physical properties of rocks. Fatt and Davis2 showed the reduction of permeability of rock with hydrostatic loading. McLatchie et al.3 and Knutson and Bohor4 related permeability reduction to compessibility of reservoir rock, again under hydrostatic loading. Wble,5 and later Redmond,6 evaluated the effects of applied radial pressure on conductivity, porosity and permeability of sandstones. In this latter work, no axial stress was applied. Dobrynin7 reviewed much of the previous work done . on the effects of overburden pressure on physical properties of rocks. He concluded that changes in physical properties are controlled to a large extent by pore compressibility of the rock. Several sets of curves developed from empirical relations are presented. These curves permit estimation of change of properties with net overburden pressure, knowing the pore compressibility and porosity of the rock. Net overburden pressure is defined as (Pe - 0.85 Pi ) where Pe is the

By R. J. Stokes

This paper compares the room-temperature mechanical behavior of magnesium oxide crystals containing 'fresh' and 'grown in' sources. 'Fresh' dislocation sources introduced by cleavage or mechanical contact move and multiply to generate slip bands at 3000 psi. Macroscopically the crystals yield smoothly at 6000 psi and can be quite ductile. When 'fresh' sources are eliminated by chemical polishing the crystals have to rely on 'grown in' sources to initiate slip. They then deform elastically up to extremely high stresses (-30 to 50,000 psi) yielding with a sharp stress drop down to the level at which Ifresh' sources operate. Grown in' sources are considered to be associated with impurity wecipitate particles or inclusions. Annealing crystals at 2000°C dissolves these particles thereby eliminating sources for slip. The crystals then become consistently stronger (> 70,000 psi) approaching within 1/10 of the theoretical strength. Dislocations of the grown-in network do not move under stress to nucleate slip. It is proposed that they are locked electrostatically. DISLOCATIONS were originally conceived to resolve the large discrepency between the theoretical and real strength of solids. The idea that slip propagates by the movement of dislocations is now well confirmed both by electron transmission and etch pit studies. But this by itself is not sufficient to explain the low yield strength of crystals for there is still the need to understand where slip dislocations originally come from. Theoretical estimates place the stress to generate dislocations homogeneously in the lattice at approximately 1/30 of the shear modulus,' a value 104 to 105 times greater than the stress at which the very first manifestations of plastic deformation have been observed. Only an special cases can the theoretical strength be approached; in crystals of high perfection such as whiskers2 where dislocation sources do not preexist and in covalent crystals where the dislocations present at room temperature are almost completely immobilized by the bond character of the solid.3,4 For the most part it is necessary to assume that the yield strength of ionic and metallic solids corresponds to the motivation and multiplication of dislocation sources present beforehand. The question as to their origin appeared to be answered by the suggestion of Frank and Read5 that dislocations forming part of the grown-in structure could operate as a mill for the large scale production of dislocations. The Frank-Read mechanism is still widely accepted as the source of dislocations but a number of observations have been reported which are in serious disagreement with it. One of the most intriguing of these is that under normal testing conditions dislocations of the grown-in network appear to play no role in the plastic deformation of rock salt structure ionic solids. This was first reported in the etch pit studies on lithium fluoride by Gilman and Johnston6 and is true also for magnesium oxide. To explain the comparatively low yield stress of lithium fluoride it was proposed by a number of authors7,9 that small unresolved prismatic loops formed by vacancy condensation were acting either directly or indirectly as the dislocation sources. This proposal led Gilman10 to perform a series of detailed and careful experiments on lithium fluoride to try to identify the sources responsible for the initiation of slip. He concluded that prismatic loops played no general role and that other sources were more important. Dislocation sources in ionic crystals can be divided into two general categories. First, there

Jan 1, 1962

By W. D. Robertson, R. E. Reed-Hill

DEFORMATION of magnesium crystals in a direction parallel to the basal plane has a special significance as a result of the preferred orientation characteristic of cold worked and recrystallized polycrystalline magnesium sheet and extruded rod in which the basal plane tends to lie in or near the plane of the sheet or the axis of a rod. The principal objective of the present study is a determination of the modes of plastic deformation in magnesium single crystals in this orientation. Evidence for nonbasal slip in magnesium has been presented by a number of authors. Schmid and Was-serman&apos; indicated that pyramidal slip on {1011} < 1120> or {1012} <1120> could occur above 225°C. Bakarian and Mathewson2 stablished that the slip system {1011} <1120> operates at high temperatures and that 225°C was a lower limit for pyramidal slip. The latter authors also showed that the critical resolved shear stress for {1011} slip was 400 g per sq mm at 330°C, while that for basal slip was 66 g per sq mm at the same temperature. Thus, at 330°C basal slip should be expected for all orientations except those in which the stress axis lies almost in the basal plane. More recently Burke and Hibbard3 oserved pyramidal slip at 25°C, when the stress axis was 6" to the basal plane and 14" to a <1120> slip direction. The critical resolved shear stress for pyramidal slip was 52 g per sq mm, which is only slightly greater than their value for basal slip (46 g per sq mm). Chadhuri, Chang, and Grant4 have observed non-basal slip in creep tests with polycrystalline specimens in the temperature range 250" to 350°C. The observed slip bands, which were extremely irregular in appearance, can be explained in terms of cooperative slip on {1011} and (1010) planes which have a common slip direction. Prismatic (1070) slip in polycrystalline magnesium was observed by Hauser, Landon, and Dorn.5 It was found to occur at low temperatures (78" and 195°K) and it was accompanied by cross slip in which the cooperating plane was the basal plane. Since prismatic slip occurred only at regions of high stress concentrations, the critical resolved shear stress could not be determined. Experimental Procedure The present work was performed on crystal specimens which were all cut from the same large single crystal. The original cylindrical crystal, 0.5 x 7 in., was grown in a Bridgman type furnace in which the temperature gradient was moved past the stationary crystal in the manner described by Jillson6 and Burke.&apos; High purity magnesium was furnished by the Dow Chemical Co. with the following spectro-graphic analysis in weight percent: 0.003 pct Al, <0.01 pct Ca, 0,002 pct Cu, <0.001 pct Fe, 0.008 pct Mn, <0.001 pct Ni, <0.002 pct Pb, <0.01 pct Si, <0.001 pct Sn, and <0.01 pct Zn. The large crystal was cut into four cylindrical pieces about 1.5 in. long. A flat surface parallel to the basal plane was made by hand grinding with lubricated metallographic paper on one side of each cylinder. In order to prevent bending in subsequent cutting operations, the crystals were supported by

Jan 1, 1958

By R. D. Nelson, F. E. Bowman

Evidence has been found for a (010)a?(111)B[102]a /,11[341]/B crystallographic relationship between the monoclinic a and B phases of plutonium during the a?B transformation. The results of an X-ray diffraction study, where [010] fiber textured a samples were used in the absence of suitable single crystals indicate that the (OIO)a planes become (111)B planes upon transformation under near-equilibrium conditions. The transformation strain along the fiber axis, which was the [010] direction, was measured dila-tomekically; the measured 8.5 pct expansion compares favorably with the 8.44 pct expansion in the in-terplanar spacing represented by the (010)a?(111)B relationship. From plots of the atom positions in each of the related planes, a correspondence was deduced between the [102]a, direction and the [341]B direction. Further analysis of the two lattice structures in the light of this relationship revealed a rotation about the [102] direction of 1 deg 43 min and a slight shearing in this same direction of about 30 min. THIS paper discusses the (B crystal structure of plutonium and the orientation relationship existing between the monoclinic a and B phases during the a?ß transformation. The kinetics of the a?ß and (3 — a transformations have received extensive consideration, and because of the crystallographic complexity of these phases, the question of the mechanisms by which these transformations occur is especially intriguing. Nelson and Shyne1 evaluated the existing experimental evidence and concluded, from the indirect evidence available, that both the ß ? a and a ? ß transformations occur by a martensitic process. Their data reveal the anisotropic nature of these transformations which suggests the existence of specific crystallographic relationships between the parent and product phases. In this paper, we are concerned with the confirmation of the existence of such a relationship resulting from the a ? ß transformation and the derivation of the crystallographic details necessary to specify it. EXPERIMENTAL RESULTS X-ray diffraction and dilatometric data were obtained from samples of a plutonium having a [010] fiber texture. These cylindrical specimens, approximately 1 cm in diam, were prepared by transforming the ß phase to a under the influence of a uniaxially applied compressive load.&apos; The [0l0] direction is parallel to the direction of applied stress; it is also perpendicular to the (010) planes. This correspondence between the plane normal and the direction having the same indices is, in the monoclinic a plutonium structure, restricted solely to this (010)[010] combination. Such a specimen was mounted in an evacuated, elevated temperature specimen holder on an X-ray dif-fractometer so that the diffracting surface was perpendicular to the fiber axis. The a diffraction pattern, Fig. 1, taken at about 115ºC, revealed the predominance of the (020) reflection. This monoclinic, P 21/rn space group yields no (0k0) reflections when k is odd. The temperature was raised slowly to 160°C to effect the complete transformation to the phase; then it was lowered to 120°C so that a diffraction pattern of the ß could be obtained near the a = ß equilibrium temperature for direct comparison with the a at the same temperature. The (3 diffraction pattern, Fig. 2, obtained under these conditions showed a (222) reflection relatively much more intense than in the random pattern. The other reflections appearing with sig-

Jan 1, 1970

By F. R. Zacher

Unmined blocks in the Sewickley seam, surrounded by worked out areas, have been found to transmit overburden oads through the interval strata to the Pittsburgh seam workings 90 ft below. Operating experiences under these conditions are described in this paper. IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott&apos;s Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today&apos;s machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1953

By D. R. Parrish, T. M. Geffen, R. A. Morse, W. W. Owens

Laboratory studies of several factors affecting measurements of relative permeability were made using the three-section plastic-covered core technique. Results show that the core assembly, properly constructed, will perform as a single unit, and that the testing technique will, under suitable conditions of pressure gradient, gas expansion, and migration of partial water saturation, permit measurement of flow characteristics not affected by technique. Wettability equilibrium is readily established in cores exhibiting strong wetting preference to water or oil when initially saturated with water. Laboratory tests must be conducted so that saturation changes represent those that occur in the reservoir. Immediate implications of saturation history are (1:) that the possibility exists of increasing the displacement efficiency of solution gas drive reservoirs over the natural process, and (2) residual gas saturations following water flooding in gas or gas condensate reservoirs will be 15 to 50 per cent pore space rather than 1 to 11 per cent as generally believed. INTRODUCTION Solutions of petroleum reservoir problems pertaining to production performance require the use of true relative permeability characteristics. &apos;This relationship of fluid conductivity and saturation has been obtained by reservoir engineers in four ways, namely: 1. From past gross reservoir performance and the extrapolation of this data based on experience,1,2 2. By using published fluid flow relationships obtained in laboratory studies on general type porous materials,3, 4, 5 3. By attempting a mathematical derivation of flow behavior," using some experimentally obtained characteristics of reservoir rocks, and 4. By laboratory flow tests using representative rock samples of a reservoir. The first three methods listed above have shortcomings which make their use limited or questionable. Production characteristics of only certain processes are obtained from field data and these are not available at the beginning of a reservoir&apos;s producing life, at which time they are desirable. It is fortuitous if general fluid flow characteristics obtained experimentally have accurate application to specific field problems. Also, it is felt that at this time there is not sufficient knowledge of the flow behavior of oil, water, and gas in porous materials to enable applicable analytical description of this to be made based on other measured rock characteristics. Measurement of relative permeability in the laboratory offers the only direct method subject to adequate checking for determination of flow characteristics applicable to field problems. Primarily, this paper deals with laboratory experiments to establish the effects of several factors on the measurement of relative permeability and the practical significance of this knowledge. Laboratory flow tests are essentially model studies; the gross reservoir being represented by a small rock sample. It is necessary to simulate in experiments all the factors of importance which influence flow in the reservoir, as well a.; to eliminate effects peculiar to the model studied to assure measurement of valid flow behavior. Factors which affect the measurement and behavior of fluid flow in porous materials have been studied by other investigators.3,7,8,9,10,11 This analysis is not intended to evaluate fully all factors involved, but to establish first the validity of measurements by the technique used and then study flow behavior under various conditions. The studies reported are as follows: 1. Effects of pressure gradient, 2. Effects of gas expansion in tests conducted at near atmospheric pressure, 3. Effects of migration of a partial water saturation in oil-gas-water systems, 4. Effects If wettability characteristics of the system. and 5. Effects of the fluid saturation history. The first three are important only in laboratory measure-

Jan 1, 1951

By W. J. Helfrich, C. L. Sollenberger

Many present direct reduction processes utilize iron ore concentrates for the production of sponge iron and the sponge iron is usually preferred as an agglomerate. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. The present paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. The kinetics of iron oxide reduction have been I studied by numerous investigators1-4 and a rate equation for the hydrogen reduction of hematite and magnetite has been proposed. Mc Kewan&apos; obtained kinetic data for the reduction of hematite spheres sintered at 13&apos;70°C (2498&apos;F&apos;). The kinetics of magnetite reduction was studied by Quets. He compacted the oxide at a pressure of 1 ton per sq cm and sintered the specimens to densities of 95 to 96 pct of theoretical. These studies demonstrated that the reduction of iron oxide is a topochemical process and that the rate of reduction is proportional to the receding surface area of remaining iron oxide. Thus, the measurement of the kinetics of iron oxide reduction depends upon the development of a measurable and well defined interface between metal and reacting oxide. It is evident that the reduction rate will be constant only when the rate of formation of the reaction product layer is constant. It was recognized by Joseph&apos; and Edstrom&apos; that the physical character of the oxide will determine the configuration of the interface between oxide and metal. The reduction of oxides which exhibit few pores or no interconnected pores should proceed by topochemical processes. However, if a massive or dense crystalline ore cracks during the reduction of the oxide, thus allowing the reduction to Proceed away from a well defined oxide/metal interface, then the observed reduction rate will vary or change during reduction. From a process standpoint, it would be difficult to apply absolute reduction rates determined for crystalline or nonporous iron oxide to the direct reduction of a porous pellet of iron ore concentrate. Most present direct reduction processes are attempts to utilize iron ore concentraates in the production of sponge iron. The sponge iron is usually preferred in an agglomerated form for subsequent melting practices. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. One process for preparing such a product has already been de-scribed. This paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. ORE CONCENTRATES STUDIED A magnetite concentrate from Reserve Mining Co. and a hematite concentrate from U.S. Steel Corp. were used in preparing pellets for these experiments. A head analysis of these concentrates is given in Table I. To compare the reduction rates of pelletized concentrates, it was necessary that each pellet contain equal amounts of oxygen which could be removed by reduction, regardless of the oxidation state, i.e., Fez% or Fe304. Also, because of the difficulty in preparing spherical pellets of uniform size, weight, density, and porosity for experimental purposes, pellets of a cylindrical shape were formed in a press.

Jan 1, 1961

By J. L. Huitt, IM. L. Slusser, E. E. Glenn, M. L. Slusser

This paper is concerned with: (1) an analysis and interpretation of the filtration characteristics of drilling muds on filter paper, and (2) an interpretation of early stage "filtration" on consolidated synthetic porous media, herein referred to as the "surge loss" period. It is shown that water-loss data can be plotted so as to disclose the existence of a surge period, a non-uni-form cake thickness period, and a constant pressure filtration period. The same periods occur during exposure of consolidated porous media to muds. The data on consolidated porous media indicate that: (1) mud particles bridge pores inside porous media during the surge period, and (2) "filter cake" build-up inside porous media occurs during subsequent filtration. The data also show that the surge loss increases with sample permeability and with pressure differential. INTRODUCTION The phenomenon of mud filtrate invasion into porous sands of a drilling well has been recognized for many years.1,2,3,4 Part of API Code 29 is concerned with the filtration testing of a drilling mud to yield data on this subject. In a number of investigations "plastering properties" of muds were studied,5,6,7,8 "plastering" apparently meaning cake forming properties. In such studies the characteristics (thickness, permeability, and toughness) of the cake and the rate at which the liquid phase of the mud was separated from the solids (filtration rate through the cake, commonly referred to as water loss) were measured or at least considered. From the standpoint of its effect on well productivity, filtrate invasion into "clean" water-wet pay sands (i.e., those containing no clay minerals) may not necessarily be a serious problem. An increase in water saturation in the zone immediately around the wellbore would cause loss of oil permeability. However, in such a system, much of this water may be removed by oil production. If filtration occurs into "dirty" sands (i.e., those containing appreciable clay minerals), clay swelling or other mechanisms may cause losses in oil permeability which cannot be overcome by oil production.&apos;.&apos; The phenomenon of mud particle invasion into the pay sand of a drilling well was considered to be a possible serious factor in the early days of rotary drilling. Opinions varied as to whether drilling fluids "mudded up" and "sealed" oil sands. In 1932 Rubel,9 Gill,10 and Parsons," in separate papers, presented differences of opinion together with some laboratory and field data concerning loss of oil production caused by drilling fluid invasion into pay zones. These papers, and the discussions, furnish a large background on this subject and indicate the very clear thinking of many men at a time when petroleum production technology was in its infancy. Jones and Babson,6 and Silent,&apos; experimentally found that the depth to which mud particles invaded water-saturated sand packs was small (no greater than 1/16 in). Arn-quist12 in 1937 observed loss of water permeability due to invasion of mud particles into water-saturated, consolidated, sandstone samples. Williams and Cannon5 studied the filtra-tion properties of drilling muds and mentioned "sludge" which penetrated a short distance into the water-saturated filtering medium (sand pack). Byck5 concluded that formation permeability had no effect on the plas-

Jan 1, 1958

By D. C. Ganow, N. J. Grant, I. R. Silver, A. R. Chaudhuri

The structural changes that result when a metal is "cold worked" lead to higher values of yield and tensile strength on subsequent deformation at room temperature. Further it has been shown that the beneficial effects of cold work are, to some extent, maintained even at elevated temperatures. The strength improvements from prior cold work decrease as the temperature is raised and are a function of grain size, amount of cold work, and strain rate (or time of test). If recrystallization occurs during test, the cold-worked material may even show weaker stress-rupture properties than the annealed material. A question that arises is whether there is a significant effect on the subsequent creep behavior if the prior deformation is performed under creep conditions at high temperatures not too different than the test temperature, but at significantly different strain rates and for various amounts of strain. An answer to this question was sought in the work described in the present paper. PROCEDURE Two materials were used in this work, high-purity aluminum and a solid-solution A1 2 pct Mg alloy. The compositions are shown in Table I. The grain size in the two materials was 0.2 to 0.3 mm. The deformation for both the prestraining and for the creep tests was at constant stress. The procedure adopted was to prestrain a specimen to the desired elongation, remove the load, and cool to room temperature rapidly by spraying. the test bar with cold water. The specimen was then placed in a creep machine, held at the test temperature for less than 5 min, and loaded. Less than 15 min was required to bring the specimen to temperature. The creep stress was based on the diameter resulting from the prior strain, and values of elongation at fracture listed in the tables do not include the respective elongations resulting from the prestrain. The choice of the stresses for the prestrain and for the creep tests was made so that the tests could be completed in relatively short times to maximize any effect of prestrain. The specimens had a gage length of 1 in., the pure aluminum specimens having a diameter of 0.150 in. and the alloy specimens a diameter of 0.125 in. For pure aluminum, prestrain was at 400&apos; and 600°F with testing at 500°F; for the alloy, prestraining was at 700°F and testing at 600°F. RESULTS The prestrain conditions for the aluminum and the alloy specimens are shown in Tables I1 and IV. In addition to showing the time required to achieve the desired prestrain, the expected rupture Lives are given which would have resulted had the creep prestrain been continued to fracture. The prestrained and the annealed specimens were then tested in creep to fracture; the temperature and stress for the pure aliminum specimens being 500o F and 1800 psi and for the alloy, 600&apos; F and 3400 psi. The creep curves for the prestrained and the annealed specimens of pure aluminum showed all three stages of creep; hence in addition to the effect of prestraining on the rupture life, it was also possible to determine the effect of prestraining on the minimum creep rate, and on the time and elongation at the end of each of the three creep stages. The results are shown in Fig. 1 and Table 111.

Jan 1, 1960

By J. M. McDowell, E. C. Doty, F. Morgan

Improvements in the X-ray method of measuring liquid saturation and saturation distribution are presented. Two identical direct current amplifiers have been added to measure continuously the intensities of the X-ray tube output and the beam which has passed through the core under test. The ratio of these intensities is automatically recorded on a modified Brown Electronik Recorder. Arrangements have been made to drive the core automatically and in synchronism with the recorder chart so as to give a continuous curve showing the variation of liquid saturation along the length of the core. By determining the ratio of the two X-ray beam intensities simultaneously the measurements are made essentially independent of small fluctuation in voltage and current supplied to the tube. This improved technique has been used for investigating the fluid distribution along the length of cores and core assemblies when one fluid is displaced by another. Typical results of these studies are shown. INTRODUCTION In a previous publication&apos; a method was described for measuring the oil saturation in cores which was based on the absorption of X-rays by the fluid content of the core. While that technique is capable of yielding accurate results, the original apparatus was not especially convenient for determining the fluid distribution along the length of a core. This was primarily due to the slow response of the amplifier and galvanometer and the necessity of making a point by point survey of the material under investigation. It was, therefore, not only possible for sections of the core having a variable or unusual saturation distribution to escape observation entirely, but changes in output of the X-ray generator between readings on the unknown and the monitor introduced errors in the measurements that could be avoided only by further stabilization of the source or by taking a large number of readings. This paper describes a method and apparatus for recording continuously and automatically the intensity of the X-ray beam that is transmitted by a core. The variation of saturation with time at a given section of the core may thus be found, or by scanning the core by driving it in synchronism with the recorder the saturation distribution may readily be determined. As indicated in the previous paper, the X-ray method possesses an advantage over the weighing technique in relative permeability experimentation in that the core need not be removed from the holder for the purpose of making a saturation measurement. Furthermore, the actual distribution of fluid and the effects upon that distribution of inflow and outflow heads may be investigated. And errors due to gas bubbles or loss of liquid that are frequently sources of error in volumetric methods of saturation determination are avoided. PRINCIPLE OF THE METHOD The energy in an X-ray beam that has passed through an absorbing material is expressed by the well known formula: E = E0, e-cd (1) where E, is the energy in the incident beam, µ the mass absorption coefficient, c the density or concentration of absorbing material, and d is the length of path of the beam in the absorber. The coefficient µ varies with the wavelength of the radiation as well as with the absorbing material. The output of an X-ray tube varies in an approximately linear manner with the tube current, but to the second or higher power of the anode voltage. Moreover, the quality or wavelength distribution of the radiation varies with the voltage.

Jan 1, 1950

By S. Kado, G. Derge, L. Yang

Self-diffusion coefficients of silver in molten silver have been measured by means of the capillary-reservoir method in the temperature range 1002" to 1105°C. The results can be .represented by the equation D = (7.10 i 0.06) X 10-4 exp [(—8150 ± 1130)/RT]. The heat of activation agrees within the limit of experimental uncertainty with that for the viscous flow. The validity of the Eyring and the Stokes-Einstein equations are examined on the basis of the self-diffusion coefficients obtained and the known viscosity data of molten silver. MEASUREMENT of the self-diffusion coefficient of silver in molten silver was made in the temperature range 1275° to 1378°K, using the capillary-reservoir method and &"&apos; as the radioactive tracer. The experimental arrangement is shown in Fig. 1. Silver of 99.99 pct purity (fine silver), was melted and degassed in vacuum in a graphite crucible situated inside a McDanel vacuum jacket. The crucible (4 in. tall and 1 in. ID) was protected both at the top and at the bottom with graphite shields and contained about 220 g of silver. The sample holder was a piece of graphite rod (1 in. long and 1/2 in. diam) with 4 capillaries drilled longitudinally into it. The holder was screwed onto a long graphite rod (12 in. long and 74 in. diam) which was connected to a steel disk hanging on a nylon string through a glass pulley. The steel disk kept the sample holder at the center of the McDanel tube and was heavy enough to overcome the buoyancy when the holder was lowered into the molten silver. By turning a handle connected to the pulley through a tapered glass joint, it was possible to raise or lower the sample holder without breaking the vacuum. Two such arrangements were constructed, sitting side by side in 2 Kanthal furnaces. One with non-radioactive silver in its crucible was used for the diffusion run and the other with radioactive silver in its crucible was used for filling the capillaries. To fill the capillaries with radioactive silver, the sample holder was degassed first and then lowered into the radioactive molten silver in vacuum. Purified argon gas was then admitted into the system to push the liquid silver into the capillaries. After cooling in argon, the filled capillaries were polished on emery paper to expose the top of the rod and used immediately as samples for the diffusion run which was carried out at the same temperature as that used for filling the capillaries. During the diffusion run, the samples were degassed in vacuum and lowered slowly into the nonradioactive molten silver before purified argon was admitted into the system. After a predetermined period of time, the samples were raised out of the melt and cooled in argon. The temperature of the melt was measured before and after the run with a chromel-alumel thermocouple inside a McDanel protection tube. Another chromel-alumel thermocouple attached to the outside wall of the McDanel vacuum jacket was used to indicate any fluctuation in the temperature of the furnace during the run, which was found to be less than ± 2°C for the longest run made (93 min). The temperature gradient inside the molten silver was found to be negligible. No significant difference was observed in the results obtained whether the melt was stagnant during the run or was stirred by raising and lowering the sample holder slowly a few times a minute for a distance of about 1/4 in. inside the melt.

Jan 1, 1959

By R. H. Jacoby, M. J. Rzasa

Experimental equilibrium vaporization ratios (K values) were obtained for nitrogen, methane, carbon dioxide, ethane and hydrogen sulfide in two natural gas-absorber oil mixtures and in two natural gas-Elk Basin crude oil mixtures. For each mixture of constant over-all composition, data were obtained at 100°, 150° and 200°F and at various pressures in the range 200 to 5,000 psia. Some effects of composition on the K values were obtained to serve as a guide in choosing K&apos;s for engineering calculations on other mixtures. The pressure cell used to obtain the data is a new type and is described here for the first time. INTRODUCTION The phase equilibria of complex hydrocarbon mixtures such as natural gases, crude oils and their mixtures have been studied previously for the purpose of finding equilibrium vaporization ratios for the hydrocarbon constitutents. In a few cases, such non-hydrocarbon.: as nitrogen, carbon dioxide, and hydrogen sulfide were included in the mixture. studied because they occur. in the fluids obtained from petroleum reservoirs. The increasing occurrerce. of these non-liydrocarbon.; antl their growing economic importance. make it necessary to account for them more accurately in engineering calculation.: than is now possible using the meager published data. The available data for non-hydrocarbons may he classified into two groups: namely, binary mixtures of a hydrocarbon and a non-hydrocarbon. and mixtures containing three or more components, only one of which is a non-hydrocarbon. Amon: the former. phase analyses are available for two nitrogen-HC mixtures, tve carbon dioxide-HC mixtures and three hydrogen sulfide-HC mixtures. Data for more complex mixtures are available as follows: Nitrogen-Methane-Pentane&apos;; Nitrogen-Methane-Hexane,&apos;; Nitrogen-Methane-Heptane&apos;; Carbon dioxide-Natural Gas-Natural Gasorline": Carbon dioxide-Natural Gas-Crude Oil". These data have been used generally lor engineering calculations, often with little regard for their precise applicability because data for the non-hydrocarbons in the complex mixtures being dealt with were not available. The use of K values from binary data for calculation:; involving complex mixtures is open to criticism because such K&apos;s are not a function of composition and very often show large differences from the K&apos;s for the same components in a complex mixture. Thus the effects of composition must be evaluated when obtaining K&apos;s for components in complex mixtures. Poettmann and Katz " varied the carbon dioxide content of their mixture.; from about five to ten mol per cent and found substantially no effect on the K values due to this change. This was not surprising since one might expect that changing a minor com-ponent by * three mol per cent would have little effect. It is more important to find the composition change which have the largest effect on the K values. For example. varying the methane or heptanes — plus compositions over a wide rangr may have a large effect on the K&apos;. of all components in the mixture. Interesting data to this effect were obtained by Eilerts and Smith." It was toward these problems that the experimental data presented here were directed. EQUIPMENT The pressure cell used to obtain the data i:. somewhat dif-ferent from those which have been described in the past. Photographs of the equipment are shown in Figs. 1 and 2. Fig. 1 Shows. the front panel: from a .rated position at the right the

Jan 1, 1952

By L. A. Wilson, N. H. Harrison, R. R. Clay, R. L. Reed. D. W. Reed

Experiments have been performed in a linear near-adiabatic system for the purpose of extending data on reverse and forward combustion from atmospheric pressure to 1,000 psig. Results obtained from reverse combustion appear to conform qualitatively with the existing description of the process when reaction kinetics are suitably modified to account for the increase in pressure, i.e., increasing tbe pressure decreases the peak temperature and increases the combustion zone velocity. Forward combustion appears to be a fuel dominated process wherein peak temperature and combustion zone velocity are not very sensitive to changes in pressure. The moderate effects of pressure that do exist at low flux virtually disappear at high flux providing all oxygen is consumed. With this provision. increasing the pressure decreases the frontal velocity and increases the peak temperature. Results me shown graphicaIIy which demonstrate the effects of presswe on peak temperature, rate of advance, oil recovery, air/oil ratio, carbon oxides produced and temperature distributions. INTRODUCTION Numerous field tests of oil recovery using the technique of underground combustion are now in progress. Operating pressures used are always substantially in excess of atmospheric pressure. Nevertheless, the literature contains no laboratory data pertaining to the effects of pressure except for those of Martin, Alexander and Dew.1 Unfortunately, these data appear to reflect heat losses which may have obscured some of the effects of increased pressure. The underground combustion processes are exceedingly complex, and general concepts relating to them have necessarily been described in relatively simple terms. Particularly with regard to forward combustion, the interaction between multiphase fluid flow, heat transport and various rate mechanisms is so involved that to date a rigorous treatment is not available. In this paper a linear near-adiabatic system is described which was found capable of operating at pressures up to 1,000 psig and temperatures of at least 1,100 F. Using this equipment, experiments on both forward and reverse combustion were accomplished at elevated pressures and the data presented as a function of air flux or temperature. It will be assumed that the reader is familiar with the papers of Wilson, Wygal, Reed, Gergins and Henderson on forward combustion and that of Reed, Reed and Tracht3 on reverse combustion, so that it is not necessary to repeat the details of the two processes. EQUIPMENT AND PROCEDURE It was decided to study the effects of pressure over the interval 0-1,000 psig using a near-adiabatic system. Since satisfactory operation of such a system requires very thin tubing walls, it proved necessary to insert the entire combustion tube and heater assembly into a high pressure jacket in such a way that the internal tube pressure could be counterbalanced by pressurizing the annulus. This meant that the numerous heater and thermocouple wires had to pass through gas-tight seals that required considerable effort to maintain effective. An unexpected difficulty arose in connection with the nature of the annulus pressuring gas. It turned out that the composition of this gas critically affected the functioning of the adiabatic control system. Operation of the equipment at elevated pressures was not particularly difficult. The problems that did arise were a direct consequence of the large numbers of connections and seals involved. EQUIPMENT The equipment consisted of the combustion tube which fitted within the pressure jacket. This jacket was in turn mounted on a wheeled carriage which facilitated movement and provided for rotation of the

By Oscar Johnson

The industry has been canvassed for information on methods of handling grinding steel at milling plants, an important subject overlooked in most descriptive articles on milling plant arrangements. The data collected are offered in this paper as a guide to designers and planners who have loading and storage problems to solve. WITH capacities of milling plants expanding from a few hundred tons per day to many thousand, replenishment of grinding media is an important phase of mill operation. Information on this aspect of milling procedure, solicited from several mining companies, is summarized here. At International Nickel&apos;s Copper Cliff concentrator the normally strenuous job of changing rods is considerably simplified by the use of the Garrow rod charging machine, Fig. 1. The overhead crane, Fig. 2, brings a bundle of rods, weighing four to a ton, to the loading platform of the machine, positioned in front of the mill. The rods roll one by one down the slight incline of the platform onto a conveyor which sends them into the mill. A modified version of the Garrow machine, Fig. 3, is used at the Federal mill of St. Joseph Lead Co. An overhead crane places the portable steel structure in position in front of the discharge end of any one of the five 9x12-ft rod mills. It then raises a bundle of about twenty 3-in. rods to the discharge platform of the charging machine. The rods are 11 ft 7 in. long and weigh about 278 lb. By tripping a lever the operator allows one rod at a time to roll onto the inclined rollers. A slight push by the operator sends the rod smoothly into the mill. The Union Miniére du Haut Katanga rod charging machine, Fig. 4, is mounted on a pair of wheels at the forward end with swiveling castors at the back for steering it to position for use or storage. Wheels are equipped with locking brakes to maintain the machine in position while it delivers rods to the mill. The device is made in two parts. The first consists of the base, which carries the supporting wheels, grooved rollers, and drive. The other part serves as the rod deck, which can carry up to six 3-in. x 12-ft rods. A short boom built integral with the base reaches through the mill trunnion and delivers the rods into the mill barrel. Three grooved guide rollers ,are provided to receive the rods from the sloping charging deck. One rod at a time is fed to the rollers and thus delivered into the mill. Two of the rollers are driven by 11/2-hp motor through a V-belt drive. The third roller is driven off the first by a single V belt in a groove below the rod groove and on the same center line. Rods are delivered to the charger by an overhead crane in bundles of three to six as needed. The power is supplied by cables plugged into power outlets, suitably located near the rod mill discharge end. The Oliver Iron Mining Co. uses a rod charger, Fig. 5, suspended from a monorail by cables. It is constructed .of structural steel and has two decks, each capable of carrying five rods of 4-in. maximum diameter. The rods ride in grooved free-turning rollers. Legs extending down from the mill end of the mechanism act as supports when the unit is ex-

Jan 1, 1955

By Hsun Hu

Direct observations were made on the recrystalli-zntion of a cold-rolled (110) [001] crystal of 3 pct Si-Fe by annealing thin sections of the specimen inside the electron microscope during examination. Subgrain formation, presumably by polygonization, occurs rapidly, followed by a slow increase in the subgrain size before recrystallization can be detected. No migration of the subgrain boundaries was observed, and the formation of recrystallization nuclei by coalescence of subgrains is suggested. Re-c~ystallization characteristics of various texture components were individually examined. AS reported in a previous paper: orientations of the various deformation texture components in a 70 pct cold-rolled (110) [0011 crystal of 3 pct Si-Fe were completely confirmed by transmission electron diffraction patterns taken at various areas of the specimen. These orientations can be summarized as follows: Over most areas of the deformed crystal (111) planes are parallel to the surface. These areas correspond to either $- the two main defor: mation textures, the (111) [112] or the (111) [112].2-5 Within a few areas, (100) planes parallel to the surface are frequently found. These areas represent the minor deformation texture component, the (100) [Oll] type, which is derived from rotated Neumann bands.2&apos;4&apos;5 Only in very rare instances are (110) planes found parallel to the surface. This orientation corresponds to the very weak texture component of the (110) [001] type. In a pole figure, this (110) [0011 orientation is located within the orientation spread between the two main (111) [1121 type textures. Usually the electron diffraction patterns taken at various areas of the specimen are very simple ones, i.e., for any one area the pattern consists only of sharply defined spots of a single orientation. In some areas, however, more or less continuous rings of weaker intensities are superimposed on a simple pattern, indicating the presence of a wide range of additional orientations. In order to understand in detail the recrystallization of this cold-worked crystal, the recrywtallization characteristics of each of the various deformation texture components must be examined. This can best be done by using a high-temperature stage and transmission electron microscopy techniques, whereby small areas corresponding to the various texture components can be selected individually for examination. The present paper presents results obtained by this method. MATERIAL AND METHOD Specimens were prepared from a previously studied1 single crystal of a commercial grade 3 pct Si-Fe alloy with an initial orientation (110) [00l], cold-rolled 70 pct from 0.014 in. to 0.004 in. in thickness. Thin foils were prepared by electrolytic polishing as described in the earlier paper.&apos; Specimens of this thin foil were then mounted in a high temperature stage similar to the one designed by Whelan.6 A direct current was used as the heating source. The temperature of the heating grid was calibrated by means of a Pt vs Pt-10 pct Rh thermocouple in a vacuum chamber (0.01 to 0.02µHg). Maximum variation within the temperature range of 250o to 000°C was about ± 25°C. After the desired areas were selected for examination, the specimen was heated to a low temperature for some time while the selected area was constantly watched. When no further change in structure and orientation could be observed, a higher temperature was applied. Photomicrographs and diffraction patterns were taken from time to time during examination, with the heater temporarily turned off* while the photographs were

Jan 1, 1962

By J. S. Aronofsky, A. S. Lee

Results and experimental procedures are presented covering a preliminary laboratory investigation of the compaction of reservoir rocks and its effect on porosity and permeability. "Egective" compressibility was measured by subjecting core material to an overburden load and reducing pore pressure. Preliminary results showed relatively high effective compressibilities which varied from 1.8 X 10-&apos; pore volume/pore volume /lb / in.~ for limestones to 7.7 X 10-6 pore volume/pore volume/lb/in.&apos; and even higher for sandstone reservoirs conmining large amounts of fine clay material. It appeared from the initiol results that the effective compressibility of the material could not be correlated directly with porosity and that other factors, such as the amount of clay material present might have to be taken into account. The work to date has indicated that effective compressibility factors will have to be measured for the particular reservoirs heing studied. Oil permeability of core materid was measured under various effective overburden loads from 0 to 8,000 psi. It has been found than reduction of permeability in clean sands was relatively small and the results agreed with published data. For sandstones containing large amounts of clay, preliminary tests indicated very large reductions in permeability with increasing effective overburden pressures. It is planned to continue laboratory work on this phase because of its importance in low-permeability reservoirs. INTRODUCTION During the past few years increasing interest has been shown in the differences obtained between conventional laboratory measurements on cores at atmospheric pressure and those when reservoir conditions are simulated. Since these data are used as the basis for calculations and the prediction of reservoir behavior, their evaluation under reservoir conditions is most important. The effect of the compressibility of the rock upon the reservoir behavior, as fluid pressure declines, is an important subject which has been insufficiently studied. The total pressure on any plane through a reservoir is the result of the grain-to-grain rock pressure due to the overburden and the pressure of the interstitial fluid on the plane. As reservoir fluid pressure declines, the net load on the rock phase must increase, and the result is the compaction of the rock structure which produces a decrease in pore volume. Simultaneously, the rock grains expand into the pore space as the fluid pressure declines. The result of these two effects is defined as the effective compressibility of the rock and is expressed in units of pore volume/original pore volume/psi. Work was started by Imperial in 1954 on the effects of pressure on the porosity of reservoir rock. These studies established effective compressibility factors for some limestones and dolomites. Since that time effective compressibilities have been obtained for other Canadian and some U. S. reservoir rocks. In conjunction with the study of porosity, an investigation has also been initiated to determine the effects of pressure on permeability. One outcrop and several reservoir sandstone cores have been tested to date. ROCK COMPRESSIBILITY Apparatus anD Procedure A diagram of the apparatus used in these studies is shown in Fig. 1. The equipment was constructed so that a uniform pressure, equivalent to the reservoir overburden, could be applied by the oil pump and transmitted on all sides of the core through the Lucite sheath. The sample was completely saturated by circulating brine through the mounted core. Pressure in

By Ralph H. Sweetser

C. H. Herty, Jr.,* Pittsburgh, Pa.—The procedure of the Open-hearth Committee in studying pig iron and its effects in the open hearth has been influenced by the discussions at a number of meetings of the Committee. Those discussions have brought out very clearly that, as far as the pig iron affects the quality, interference with quality should be studied for three definite types of pig iron: (1) low-silicon pig iron; (2) very high-silicon pig iron, and (3) pig iron in which the silicon varies over a wide range in short periods, such as 1 to 3 casts. If a blast furnace is running steadily at 1 per cent. silicon iron, practically no trouble, apparently, can be traced to the pig iron, but if the furnace is running from 0.60 up to 1.50 and then down to 0.60 per cent., trouble in the finished steel is liable to occur, which apparently cannot be corrected by open-hearth practice. The open-hearth discussions have shown fairly definitely that with low-silicon iron, one type of trouble arises on the finished product and with the high-silicon iron, another. Our experience with the high-silicon is that any non-metallic matter that may form, does so when the pig iron is put into the furnace; that is, silicates immediately form which are more liable to be high in silica than would happen with low-silicon iron. I think Mr. Sweetser will agree with mc that if a blast furnace is very irregular, different points in the furnace may be working irregularly, in other words, the temperature gradient all over the furnace is not uniform. We have made many determinations on that point which indicate that a varying blast furnace causes hot spots and cold spots around the periphery. If some of those spots are hot and others are cold, although the analysis of the iron may be constant, then unreduced oxide, going through on one side, and good iron, going through on the other, may mix and the average temperature of the iron is not high enough to get completely rid of the oxides. So our method of attack is directly on that point; it is our first objective. Our procedure is to make a number of consecutive tests at a blast furnace, making a detailed study of the blast-furnace operation. We follow the iron through the open-hearth heat, being sure that we know just how much of each kind of iron gets into the open hearth, and take out specified samples at certain times during the process, working on steel where no finishing additions are made in the furnace. We are following one type of iron through the billet mills and into the finished product and are obtaining complete data on open-hearth operation. Besides the ordinary chemical analyses on the samples of slag and metal, we are running samples of the plg iron, the steel in the open hearth and the finished steel, for oxygen and silicates. We are going to find out whether or not oxygen, as silicates or oxides, has some connection with this trouble. If not, we may be able to locate some other factor. I am inclined to think that the silicates are responsible, judging from the indications in some other work that the Bureau of Mines is doing in Pittsburgh. We have laid out a very definite method of testing to which we will adhere at the different plants where we are now working and at others in the future. Our aim is to

Jan 1, 1927