Search Documents

By George D. Dub

INTRODUCTION OWENS LAKE is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.2H20) and borax, (Na2B407.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. CLOSED BASINS Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I Chloride type; largely sodium chloride (NaCI) and of oceanic type, such as Great Salt Lake. Related is the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. 2. Sulphate type; largely sodium sulphate (Na2S04) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate-chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate-Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1947

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By F. N. Rhines, T. E. Leonitis

The oxide scale that forms upon magnesium at elevated temperatures is non-protective in the sense that the rate of oxidation is constant and thus does not decrease with the growth of the scale as it does with other common metals. This generality was first stated by Pilling and Bedworth' and has been verified by Suzuki2 and by ScheiL3 Pilling and Bcdworth argued that the nonprotective characteristic could be predicted from the fact that magnesium oxide occupies less space than does the metal from which it springs, wherefore the scale is not expected to cover the metal so completely as to exclude all direct access to the atmosphere. Linear oxidation is thought by Scheil to be common to all cases where the reaction occurs at the oxide-metal interface. According to Suzuki," he product of high-temperature oxidation in the air is MgO contaminated with no more than traces of a nitride. When the metal is allowed to burn freely a fume composed of cubic crystals of Mg04 is given off. Delavaults observed that excrescences form upon liquid magnesium and alloys in thc course of oxidation. Beyond this it is known that the use of atmospheres containing small quantities of sulphur dioxide6 or carbon dioxide serve to retard the oxidation of solid magnesium and that beryllium' and calciums minimize the oxidation of molten magnesium exposed to the air. Many studies have been devoted to the nature and rates of "protective" oxidation, as exemplified by the cases of copper and iron, wherein the rate is characteristically parabolic. The theory of parabolic oxidation is well developed.~ Linear oxidation, on the other hand, has received but little attention and the theories proposed by Pilling and Bedworth and by Schcil have yet to withstand careful examination. There exists no comprehensive survey of the high-temperature oxidation of magnesium (or of any other metal that exhibits linear oxidation) over a broad range of temperature, under a variety of atmospheric conditions and covering a large group of alloys. It has been the purpose of the present investigation to provide such a survey, with the object of gaining a fuller understanding of linear oxidation, especially as applied to magnesium. Experimental Procedure and Results The experimental studies undertaken were of two kinds: (I) measurement of the rate of oxidation as influenced by the 6c

Jan 1, 1946

By Welton Crook

UNLESS present in considerable proportion, metals of the precious-metal group-other than gold and silver-are not readily detected by the methods of fire assaying usually applied to ores and metallurgical products. Platinum, when present in small quantity, will ordinarily be reported as silver unless special methods of parting are used. Other elements occurring in the gold itself are all fluxed and slagged in the assay operation and if analyses are made on bullions the melting and slagging operations to which the bullion has been subjected may eliminate most of the associated elements. On the other hand, the analysis of precipi-tate from the cyanide treatment of gold ores may reveal the presence of many unexpected elements, such as tungsten and molybdenum. It is uncertain, however, whether many of the elements present in the pre-cipitate are derived from the ore gangue or from the gold itself. No very general survey of the distribution of metallic elements in gold seems to have been made. Rose and Newman,1 in connection with the composition of native gold, say in part as follows: Gold is occasionally found alloyed with copper and sometimes also with iron, bis-muth, lead, mercury, tin, antimony, palladium or rhodium. Rhodium gold from Mexico was found to be of the specific gravity 15.5 to 16.8 and contained 34 to 43 per cent of rhodium. The native alloy of palladium, gold, and silver from Porpez con-tains 85.98 per cent of gold, 9.85 per cent palladium and 4.17 per cent silver. Mal-donite, from Victoria, contains gold 64.5 per cent, bismuth 35.5 per cent (Louis). Dana' says that native gold is usually alloyed with silver in varying amounts, and that sometimes it also contains traces of copper and iron. Rare varieties contain palladium, rhodium and bismuth. Other authors, for instance Zeigler3 and Clark,4 give similar information. Most refer-ences on the subject agree that ordinary native golds contain, in common, the elements silver, copper and iron. After completion of the work of which this paper is a record, the conclusion is reached that all ordinary native gold probably does contain these elements and, although in certain cases other elements may be found to be present, that it is difficult to

Jan 1, 1939

By E. Miller, K. L. Komarek

Equatiorzs have been derived which related maximum solid solubilities in semicondcting compounds having retvograde solidus curves with 1iqllidus data. Liquidus curves in Lke Pb-Te, Pb-Se, ard PB-S systetris have been defermined by thertrzal aralyses. Fvotrz expevimental maximum solibilities ia CdTe, PbTe, uxd PbS vetvograde tetrperatures hale beep1 calculated. TIze resllts support the concept that under certaiz conditiots pronounced itjlections in the liquidis curves arc indzcatiz:e of retropade solidus curves and that the tenlperatltre of the lmaximum solid solubility will be close to the temperature of the point of inflection in the liquidus curve. The maximum solid solihility within a gvoup of homologous cottrpoods SeetlLs to increase with increasing flatness ol the liquidus curvres. The phenomenon of retrograde solubility in metals, i.e., maximum solubility in a solid terminal phase in equilibrium with a liquid phase, has been theoretically predicted by Van aar' in his calculations of hypothetical binary phase diagrams. It was not until 1926, however, that retrograde solubility was experimentally verified in the Zn-Cd system.' Since then many sys- tems with retrograde solubility have been found, so that at present approximately fifty binary diagrams with a retrograde solidus curve are known.3 Meijering4 has critically appraised the accumulated data and has presented calculations which alloy predictions as to whether or not a solidus line will be retrograde. Interest in retrograde solubility increased when it was found that the solidus curves of germanium and silicon alloyed with a great many doping elements are retrrade. The problem was treated thermody-namically by odkinson,% d all available data on solid solutions in germanium and silicon were summarized by Trumbore.7 Although it is to be expected that intermetallic compounds will also exhibit retrograde solubility, experimental evidence is much more limited. Until now retrograde solidus curves have been reported for the compounds de,' be, Ps:" ne," SnSe," and SnS.13 All these compounds are semiconductors, and the solidus curves were usually obtained by determining the carrier concentration at room temperature of samples equilibrated at elevated temperatures and then quenched. It has been hown,'' however, that it is not always possible to quench in the equilibrium compositions from above a certain temperature. Theoretical discussions have either explicitly excluded intermetallic compounds4 or not treated them with respect to retrograde slubilit.j In the following a thermodynamic treatment of retrograde solu-

Jan 1, 1967

By T. E. Leontis, F. N. Rhines

THE oxide scale that forms upon magnesium at elevated temperatures is nonprotective in the sense that the rate of oxidation is constant and thus does not decrease with the growth of the scale as it does with other common metals. This generality was first stated by Pilling and Bedworth1 and has been verified by Suzuki2 and by Scheil.3 Pilling and Bedworth argued that the nonprotective characteristic could be predicted from the fact that magnesium oxide occupies less space than does the metal from which it springs, wherefore the scale is not expected to cover the metal so completely as to exclude all direct access to the atmosphere. Linear oxidation is thought by Scheil to be common to all cases where the reaction occurs at the oxide-metal interface. According to Suzuki,2 the product of high-temperature oxidation in the air is MgO contaminated with no more than traces of a nitride. When the metal is allowed to burn freely a fume composed of cubic crystals of Mg04 is given off. Delavault5 observed that excrescences form upon liquid magnesium and alloys in the course of oxidation. Beyond this it is known that the use of atmospheres containing small quantities of sulphur dioxide6 or carbon dioxide serve to retard the oxidation of solid magnesium and that beryllium7and calcium8 minimize the oxidation of molten magnesium exposed to the air. Many studies have been devoted to the nature and rates of "protective" oxidation, as exemplified by the cases of copper and iron, wherein the rate is characteristically parabolic. The theory of parabolic oxidation is well developed.9 Linear oxidation, on the other hand, has received but little attention and the theories proposed by Pilling and Bedworth and by Scheil have yet to withstand careful examination. There exists no comprehensive survey of the high-temperature oxidation of magnesium (or of any other metal that exhibits linear oxidation) over a broad range of temperature, under a variety of atmospheric conditions and covering a large group of alloys. It has been the purpose of the present investigation to provide such a survey, with the object of gaining a fuller understanding of linear oxidation, especially as applied to magnesium. EXPERIMENTAL PROCEDURE AND RESULTS The experimental studies undertaken were of two kinds: (I) measurement of the rate of oxidation as influenced by the

Jan 1, 1946

APPROXIMATELY 3500 people thronged the Hotel Statler from February 18 to 24 for the 173rd general meeting of AIME. It was a technical extravaganza in that 82 technical sessions were held, at which 500 authors presented some 350 papers. Fortunately, Jerry Peirce, outgoing President, didn't have, to preside at all the events although after his year's stint as President, he has more than a nodding acquaintance with some of the latest problems in the mining, metals, and petroleum industries. Although the Welcoming Luncheon on Monday noon was the official opening of the meeting, Local Section Delegates and the Board of Directors convened on Saturday and Sunday, respectively. The large attendance and business like demeanor of these two groups was in accord with the energetic and competent service they have rendered the Institute through the year. To the applause of engineers and their wives who thronged the grand ballroom of the Statler for the Welcoming Luncheon, President Peirce introduced Oliver B. Hopkins, president of the Canadian Institute of Mining and Metallurgy and C. Gerow, secretary of CIM. Dr. Hopkins brought greetings from the CIM and expressed his satisfaction in the splendid spirit of cooperation that exists between the two Institutes. Dr. Hopkins is president, Interprovincial Pipe Line Co., Toronto, and counts as a close personal friend M. L. Haider, who is the 1952 President of AIME and lately of Toronto where he was a director and general manager of Imperial Oil Ltd. Mr. Haider will be known shortly as Mike to thousands of AIME members as he makes his Local Sections presidential tour. There was a pause in luncheon proceedings when Judge Harold R. Medina arrived amid the applause of the audience and somewhat breathless from his trip via motorcade from an antitrust trial against investment bankers at the courthouse downtown. With the Judge at his elbow, President Peirce took the opportunity in his introduction to good humoredly chide the Judge for the vixenish habits of public servants in their treatment of astute businessmen. The successful inventor who patents his inventions is a monopoly; the copper manufacturer who buys his competitors a drink is in collusion; but the business failure need only look to the government for a subsidy, Mr. Peirce pointed out. Judge Medina, quickly captured the admiration of his listeners. He spoke about justice, deploring partisan deals on nominations for judge-

Jan 1, 1952

By T. E. Leonitis, F. N. Rhines

The oxide scale that forms upon magnesium at elevated temperatures is non-protective in the sense that the rate of oxidation is constant and thus does not decrease with the growth of the scale as it does with other common metals. This generality was first stated by Pilling and Bedworth' and has been verified by Suzuki2 and by ScheiL3 Pilling and Bcdworth argued that the nonprotective characteristic could be predicted from the fact that magnesium oxide occupies less space than does the metal from which it springs, wherefore the scale is not expected to cover the metal so completely as to exclude all direct access to the atmosphere. Linear oxidation is thought by Scheil to be common to all cases where the reaction occurs at the oxide-metal interface. According to Suzuki," he product of high-temperature oxidation in the air is MgO contaminated with no more than traces of a nitride. When the metal is allowed to burn freely a fume composed of cubic crystals of Mg04 is given off. Delavaults observed that excrescences form upon liquid magnesium and alloys in thc course of oxidation. Beyond this it is known that the use of atmospheres containing small quantities of sulphur dioxide6 or carbon dioxide serve to retard the oxidation of solid magnesium and that beryllium' and calciums minimize the oxidation of molten magnesium exposed to the air. Many studies have been devoted to the nature and rates of "protective" oxidation, as exemplified by the cases of copper and iron, wherein the rate is characteristically parabolic. The theory of parabolic oxidation is well developed.~ Linear oxidation, on the other hand, has received but little attention and the theories proposed by Pilling and Bedworth and by Schcil have yet to withstand careful examination. There exists no comprehensive survey of the high-temperature oxidation of magnesium (or of any other metal that exhibits linear oxidation) over a broad range of temperature, under a variety of atmospheric conditions and covering a large group of alloys. It has been the purpose of the present investigation to provide such a survey, with the object of gaining a fuller understanding of linear oxidation, especially as applied to magnesium. Experimental Procedure and Results The experimental studies undertaken were of two kinds: (I) measurement of the rate of oxidation as influenced by the 6c

Jan 1, 1946

By Merton C. Flemings, Harold D. Brody

Analyses that include diffusion of solute in the solid phase are formulated to describe solute redistribution in dendritic solidification of metallic alloys. The analyses are based on conditions that include negligible undercooling before nucleation of solid phases, negligible increase of solute in advance of the tips of growing dendrites, complete diffusion within the liquid over distances the order of dendrite spacings, and a plate-like dendrite morphology. The classical nonequilibrium freezing equation, Cs = kCo(I - fS)k-l accurately describes solute redistribution between dendrite arms for the solidification processes considered, provided diffusion in the solid is negligible. To account for the effect of diffusion in the solid, an analytic expression is given which is similar inform to the classical expression. 172 addition, a numerical-analysis procedure is etnployed to examine in more detail the effect of diffusion both during and after solidification. The analyses are intended for application to solidification of castings and ingots to describe a) final solute distribution after solidification and cooling to room temperature (microsegregation) and b) local fraction solid as a function of ternperatcre within the solidifying casting or ingol. SOLUTE redistribution in cellular and dendritic solidification has been discussed quantitatively in recent papers'-3 and in a series of earlier work.4-6 However, none of the analyses developed have permitted close correlation of theory with final solute distribution (microsegregation) observed in castings and ingots. In this paper, discussion is given of approximations which may reasonably be made in mathematical treatment of microsegregation, and analyses are presented based on these approximations. Numerical results are given for Al-Cu alloys. In a second paper the analyses will be compared with exeriment.7 CLASSICAL ANALYSIS The classical quantitative treatment of solute redistribution within a closed "volume element" has been derived repeatedly, for example by Gulliver,4 Scheil,' and Pfann.' This "classical nonequilibrium solidification equation" is written for constant partition ratio: where Cs = interface composition of the solid when the weight-fraction solid within the "volume element" is fs (weight fraction, wt pct); k = equilibrium partition ratio; Co = initial alloy composition within the volume element (weight fraction, wt pct). Assumptions of Eq. [11 are: 1) There is negligible undercooling before nuclea-tion, or from curvature or kinetic effects. 2) There is no mass flow in or out of the volume

Jan 1, 1967

J. R. Lane (Metals Research Laboratory, Washington)—A new type of deformation called "kinking" has recently been described. Is there any relation between the "rumpling" described in this paper and "kinking?" D. C. Jillson (author's reply)—Both are manifestations of bending about [210] axis. The difference is one of degree. W. C. Ellis (Bell Telephone Laboratories, New York) —Some observations of deformation in zinc recorded in this paper may be applicable generally to flow in metals. One of these, deformation in torsion without evidence of slip or twinning in the early stages and with startling ease, when the twist is about the hexagonal axis, adds another method of flow to the presently increasing list of mechanisms. This illustrates again that a crystal will utilize any realizable process to flow and relieve stress. The process is not necessarily classical directional slip—& this case, it is rotational slip. The question naturally occurs: Will face-centered cubic metas stressed by twisting about an octahedral axis flow in a similar manner by rotation on an octahedral plane? I would like to ask Dr. Jillson if he has made any experiments or knows of any experiments of this type on face-centered cubic metals? Face-centered cubic metals possibly would behave differently from zinc, since, for one thing, the stacking sequence is different for the two structures. The results of such experiments, however, would be instructive in providing more information about deformation processes. D. C. Jillson—Dr. Roy E. Swift, working in the Hammond Laboratory at Yale, performed a twist test on a single crystal of brass. The work has not been published, and I do not know the crystallographic direction of the axis of the specimen used. Lo-ching Chang (Columbia University, New York)— Observations similar to Figs. 1 and 2 of the paper were obtained by us during the bending and unbending of an orthorhombic Au-Cd alloy.'l This orthorhombic alloy is the product of diffusionless transformation from a single crystal of p Au-Cd alloy (CsC1 structure) containing 47.5 atomic pct Cd on cooling to about 60 "C.62 Referring to the effects of annealing, has the author tried any loilg time high temperature anneal, such as 150 to 200 hr at 40O°C? D. C. Jillson—No. C. Crussard (Ecole des Mines, Paris: France)—I

Jan 1, 1952

By Robert E. Green

Formulae are given for calculating the modes of wave propagation in a single-crystdl specimen possessing a given crystallographic orientation. Such calculations lead to determination of the orientation factor appearing in the Granato-Lucke theory for the attenuation of these waves due to dislocation damping. A detailed treatment is given for the case of an aluminum crystal possessing the orientation having a maximum Schmid fac -tor of 0.5. FOR a number of years the attenuation of ultrasonic waves propagating in metals has been used to investigate various phenomena causing internal friction.Most of the experiments were performed on polycrystalline test specimens and the waves were assumed to be propagating in an isotopic medium. However Alers 6 in 1955 and more recently Hikata et at. Chiao and Gordon,8 and Swanson and Green 10 have used measurements of attenuation of ultrasonic waves to study internal-friction changes in single crystals. These authors were concerned with the energy losses experienced by the ultrasonic waves due to dislocation motion induced by plastic deformation of the crystals. Alers measured the attenuation of 7 mc per sec ultrasonic pulses propagating in zinc single crystals before, during, and after plastic deformation. Simultaneously he measured the time-dependent plastic strain at constant stress in order to study the correlation between this strain and attenuation. The crystals were oriented in such a way that the applied stress provided a direct shear on the slip plane, thus causing the deformation to proceed by slip on this plane. At the same time the high-frequency sound pulses were sent through the crystal perpendicular to the slip plane. He found that the attenuation of transverse waves, the stress vectors of which lie in the slip plane, was very sensitive to the deformation. The polarization of the particle displacements, associated with these waves, relative to the applied static shear stress, and hence the direction of slip, had no obvious effect on the results. The attenuation of longitudinal waves was affected by the deformation only when the slip plane was not perpendicular to the propagation direction. This indicated that the attenuation was caused by dislocations introduced by the deformation and moving only in the slip plane. Hikata et al. made simultaneous measurements of attenuation, velocity changes, and stress-strain relations on aluminum single crystals deformed in tension. Both longitudinal and shear waves were used, at frequencies of 10 and 13 mc per sec. They placed emphasis on the choice of propagation modes and polarization of the ultrasonic waves, such that interactions between these waves and dislocations on selected slip systems could be investigated. They also selected specimens possessing specific crys-tallographic orientations, which allowed investigation as a function of the number of equally favored slip systems under the applied stress. They found that, for symmetrical orientations, the change of attenuation decreases with the increasing number of equally favored slip systems, i.e., in the order

Jan 1, 1964

By T. E. Tietz, J. E. Dorn

Activation energies for creep of copper at intermediate temperatures, where crystal recovery was negligible, were determined by the simple technique of rapidly alternating the test temperature between and T2 (T2 = TI + about 10°K) throughout a constant stress creep test. The activation energy for creep H was found to be 37,000± 3,000 cal per mol, independent of stress and strain. The same creep laws as have been previously established for high temperature creep were found to be valid for creep at intermediate temperatures. But the AH was found to be lower than that for self-diffusion in the intermediate temperature range whereas it is known to be equal to that for self-diffusion at high temperatures. IT is now well established that creep at high temperatures can be correlated by the functional relationship'-" e = f(?) s = constant [I] where E is the total plastic strain, f is the function that depends on the stress, ? = f e -- dt, t is the duration of test, e is the base of natural logarithms, AH is the activation energy for creep, R is the gas constant,T is the absolute temperature, and s is the stress. Thus, identical values of are achieved during creep under a given stress at two alternate temperatures at the same total strain. At the same strain therefore where subscripts refer to the two alternate temperature conditions of test. Consequently, the activation energy for high temperature creep is readily obtained with the aid of Eq. 2. Activation energies so obtained have been observed to be insensitive to the creep strain at which they are evaluated, the applied stress, grain size, minor alloying additions,'-' cold worked state, and the presence of thermally stable dispersions of intermetallic compounds in an a solid solution matrix Furthermore, the activation energy for high temperature creep is very nearly equal to that for self-diffusion in all cases where adequate data are available for comparison." " The apparent identity of the activation energies for high temperature creep and self-diffusion strongly suggest that high temperature creep arises from a dislocation climb process. This hypothesis is further strengthened by the fact that the energy of activation for high temperature creep is insensitive to the applied stress," and by the observations that the correlation suggested by Eq. 1 cannot be ex- tended to temperatures below those for rapid crystal recovery. When using the activation energy for self-diffusion, Eq. 1 fails to give the required correlations between creep curves at various intermediate temperatures.' This suggests that the dislocation climb mechanism for creep might be superseded by some alternate mechanism in the intermediate range of temperatures. This investigation was initiated in a preliminary attempt to ascertain the type of creep law that might be valid in the intermediate range of temperatures. Special consideration, however, was given to the determination of the activation energy for creep in this range because the Becker-Orowan', " and the Mott-Nabarro10 theories for transient creep suggest that the activation energy should increase

Jan 1, 1957

By A. W. Dana, F. J. Shortsleeve, A. R. Troiano

The phenomenon of flake formation which may occur during cooling or room temperature aging of large steel sections is caused by a combination of hydrogen and stress. As such, the transformation characteristics of austenite in a particular section play a major role in the occurrence of flakes. Isothermal and continuous cooling studies demonstrated that flake formation is particularly sensitive to nature, distribution, and relative proportions of the microconstituents in the cooled sections. In the absence of transformation stresses, abnormally high hydrogen contents could be tolerated without flaking. Flakes were not found in the absence of transformation stresses. No correlation existed between average hydrogen content and flake formation where cooling stresses were low. Hydrogen in the steel was a necessary but not sufficient condition for flake formation. DESPITE a long history of laboratory and commercial investigations, the mechanics of hairline crack or flake formation in large steel sections remains unresolved. Recent publications1-5 emphasize that flaking is still a serious problem.* immediate cause of flaking is the pressure exerted by entrapped hydrogen gas that collects in small internal cavities or voids during cooling. When the temperature of steel is low enough to preclude extensive plastic flow, the cavity pressures cause local brittle fractures (flakes). 2—The microsegregation and transformation stress theory. According to this theory, flaking results from stresses arising from the volume changes accompanying the formation of martensite and/or low temperature bainite after a large portion of the section has transformed at elevated temperatures. The proponents of the hydrogen theory suggest that stresses from other sources may be additive to the stresses produced by hydrogen and may, in some cases, provide the increment of stress necessary to produce flakes. However, the critical aspect of this theory is that no stress, except that produced by hydrogen pressure, is believed to be sufficient in itself to produce flakes. For practical considerations, this means that the only safe thermal cycle is one that reduces the hydrogen content to some low critical level below which flaking will not occur regardless of the state of transformation. On the other hand, the transformation stress theory does not rule out the embrittling effect of hydrogen. This theory simply proposes that flaking does not occur in the absence of transformation stresses. With the transformation stress theory as a basis, commercial antiflaking cycles would be designed to complete the transformation of austenite prior to cooling to ambient temperatures. Both of these theories appear compatible with industrial experience. Antiflaking cycles, such as cooling at extremely conservative rates or soaking for periods of time in the upper subcritical temperature ranges prior to cooling to ambient temperatures, may allow the following: 1—diffusion of hydrogen out of the section and, as a consequence, reduction of the hydrogen content to some safe minimum value (hydrogen pressure theory) and 2—complete decomposition of the austenite at rela-

Jan 1, 1956

By L. O. Brockway, W. C. Bigelow, J. A. Amy

Specimens of Inconel-X alloy solution-treated at 2050°F and aged for periods of 1, 10, 100, and 1000 hr at 1200°, 1400°, and 1600°F have been examined by electron microscopy and by electron and X-ray diffraction. Four minor phases were identified: titanium nitride, niobium nitride, an M23C6 complex carbide, and the intermetallic ? phase. The two nitrides were found in all of the aged specimens and in the solution-treated alloy, the y' phase formed at all aging temperatures, while the M23C6 carbide formed only on aging at 1200° and 1400°F. Variations in the hardness, rupture strength, creep strength, and yield strength of the alloy have been shown to be related to variation in the size and distribution of the particles of the y' phase within the matrix grains of the alloy, with maximum values of these properties occurring when there is a maximum amount of the phase present and a fine state of dispersion of the particles prevails. THE nickel-chromium alloys containing titanium and aluminum are widely used in applications requiring high strength at elevated temperatures. Studies on relatively simple ternary and quaternary alloys'-4 have indicated that the favorable high-temperature properties of these alloys are related to the precipitation of an intermetallic ?'-phase having a structure based On that of the Ni3A1 phase of the nickel-aluminum system. The present investigation was undertaken to identify the minor phases and to study the microstructural changes occurring in one of the more complex commercial alloys as a result of aging in the service temperature range, with particular emphasis on investigating the role of the ?' -phase. The microstructural changes were studied by electron microscopy and the minor phases were identified by X-ray and electron diffraction. MATERIALS AND METHODS Inconel-X alloy was selected for this investigation because the previous studies of Frey, Freeman, and white6 provided extensive information on the variations in metallurgical properties of this alloy resulting from high-temperature aging treatments. Specimens aged 1, 10, 100, and 1000 hr at 1200°, 1400°, and 1600°F were made available for the present use. These were taken from 1-in. round-bar stock of a commercial heat having the following weight composition: 0.04 C, 0.56 Mn, 6.59 Fe, 0.007 S, 0.38 Si, 0.03 Cu, 73.22 Ni, 14.97 Cr, 0.78 Al, 2.38 Ti, and 1-02 Nb. They were solutjon-treated at 2050 for 4 hr and then water-quenched prior to aging. Powder X-ray diffraction patterns were obtained from insoluble minor phases which were separated from the alloys by digestion in the reagent of Mahla and Nielsen.6 Back-reflection patterns were obtained from electrolytically polished surfaces of the bulk search to detect the ?'-phase' Cu-K a radiation was used in both cases. In the electron-diffraction studies, the general method developed by Heidenreich, Sturkey, and

Jan 1, 1959

By C. W. Allen, L. C. Moore

THE Mather mine, of the Negaunee Mine Co., is within the limits of the City of Ishpeming, on the Marquette iron- range in Michigan's Upper Peninsula. It is named for William G. Mather, who has served as President, and Chairman of the Board, of The Cleveland-Cliffs Iron Co. for well over 50 years. The property comprises nearly the square mile of section 2, T.47 N. R.27 W., which, except for 20 acres in the northeast corner, was leased by The Cleveland-Cliffs Iron Co. to the Negaunee company. The latter is a partnership of Cleveland-Cliffs and the Bethlehem Steel Co., organized to equip the property, retaining Cliffs in charge as operator. Shipments of ore from this area are mainly through Marquette, which is 16 miles to the northeast on Lake Superior, or through Escanaba, a Lake Michigan port, 65 miles to the south. Cleveland-Cliffs, in 1943, operated 12 mines in the Lake Superior district, with shipments of 6,635,576 tons for the year. GEOLOGY The north footwall of the Marquette Range synclinorium outcrops near the north line of sec. 2, the iron formation dipping to the south at an angle of about 40º. The south side of the trough reappears at a distance of 4 ½ miles on sec. 26 and the surface geology between shows iron formation or intrusive diorites. The latter are harder than most phases of the iron formation and, as a result of glacial action, appear as buttes or low-lying hills. The general elevation of sec. 2 is about 1450 ft. above sea level, or 850ft. above Lake Superior, and the higher diorite outcroppings about 1600 ft. above sea level. The geological structure has been complicated by a series of major and minor faults, one of which may be illustrated by the diorite sheet, which tilts south with the iron formation in the north half of the section and then reappears near the center to repeat this sequence. Sectionally the geological series includes a nearly eroded capping of Goodrich quartzite followed by the considerable thickness of Negaunee iron formation, which is cut by intrusive dikes or diorite sheets, and underlain by the Siamo slates grading into quartzites. The ore deposits occur mainly in troughs formed by the intersection of impervious dikes and the footwall slate, but include locally enriched lenses or bands in the iron formation and also interbedded with the Siamo slate. The ore is a soft red hematite with an indicated dried analysis from the surface drilling to date of 61.50 per cent Fe, 0.134 per cent P, 5.40 per cent Si, 2.87 per cent Al and 0.015 per cent S. EXPLORATION A diamond-drilling campaign started in 1937 actually had its inception in 1917, when a number of shallow test holes were put down for the purpose of locating ore that might be quickly developed and mined

Jan 1, 1945

By David W. Kennedy, Stephen P. Harrison

In the past few years, a new system has been developed for ventilating longwall panels in some gassy coal mines in the Northern West Virginia area. This system utilizes a five or six foot diameter air shaft to ventilate a group of three or more longwall panels dependent on conditions. This shaft exhausts all the air needed to, ventilate the active longwall and adjacent gob areas. By law, this bleeder fan can handle double the maximum methane concentration allowed in a normal return air course. As a result, the methane that must be diluted by the primary ventilation circuits is reduced. This new ventilation system was first conceived by mine management as a means of coping with a sudden shift in production mode that occurred a few years ago. Formerly, production often consisted of room and pillar mining with continuous miners. The high methane liberation rate was handled by driving entries around a large block of coal prior to mining. This isolated the future mining area from the adjacent coal seam and allowed a major portion of the trapped in situ methane to bleed off. Also, these bleeders served to exhaust return air from the mining area. Once the bleeders were established, productive mining could start. When the decision was made to shift production mode from continuous miners to longwall mining, some of the bleeders did not encompass large enough unmined areas under the old ventilation system to initiate longwall production. Also, many other established continuous miner section bleeders were either improperly positioned or too restricted for longwall ventilation. Unfortunately, standard bleeder development can take up to two years' time. In order to eliminate the old style bleeder system and maintain or increase the margin of safety for ventilation, the bleeder shaft system was conceived. With this system, the only entries developed are those necessary for the longwall, significantly reducing the production delay. In this area, the Pittsburgh #8 coal seam dips to the northwest. As a result of this dip, the bleeder shaft is constructed in the northernmost set of tailgate entries. In this manner, groundwater accumulations can be pumped to the surface and bleeder entries kept dry. During the initial longwall entry development, the bleeder fan can be used to ventilate entries adjacent to virgin coal where significant methane liberation often occurs. Once longwall production starts, the bleeder shaft exhausts the entire air quantity necessary to safely ventilate the longwall. As the bleeder entries deteriorate, the air quantity and pressure characteristics must be increased. The extreme flexibility of the centrifugal fan used at the surface allows the air quantity and pressure to be adjusted without stopping the fan. This improves safety by decreasing the possibility of a methane buildup resulting from the fan being out of service. The bleeder shaft system of ventilation, developed by mine management in Northern West Virginia, can provide a safe means for effectively ventilating longwall panels in excessively gassy mines. This system should be considered where mining conditions are comparable.

Jan 1, 1982

By C. C. Wright, R. J. Day

Although data on the exact tonnage of recoverable coal silt are not known, the quantity produced in 1943 was estimated to be over five million tons for the anthracite region of Pennsylvania alone. Since that time the recovery of the No. 5 buckwheat size previously included in silt estimates has increased greatly thus reducing the total silt tonnage. As a compensating factor, however, the methods of recovering silt previously escaping into the rivers and streams have been markedly improved so that the net figure may not have changed materially. Comparable estimates for bituminous coal are lacking, but undoubtedly the silt represents a significant tonnage. With the trend toward increased wet cleaning of the smaller sizes of bituminous coal, it is to be expected that even greater quantities of silt will be available in the future. The raw silt from anthracite collieries usually contains a high mineral matter content, but technological developments in fine coal cleaning have been making rapid advances and it appears probable that more extensive use of these methods will be employed in the near future. Bituminous coal silt in many instances contains a similar high mineral matter content. As with anthracite silt, however, the cleaning of this material, where necessary, appears both technologically and economically feasible. With a view to upgrading the size and value of silt, considerable laboratory and pilot plant work has been conducted by a number of organizations on what is commonly known as pelletization. Actually the process is one of extrusion in which the moist silt is extruded from a die in the form of rods, which usually break into relatively short lengths—a few inches long—as they fall from the die. Fig I is a photograph of some extruded 3/8-in. diam pellets and of the anthracite silt from which they were produced This technique of producing larger sized material from fines is by no means new, having been used extensively by the industrial carbon and clay industries for years.' The application of the process to coal silt appears, however, to be relatively new. The first major program of investigation dates back only to July 1945, when a group of engineers representing the Anthracite Institute, The Pennsylvania State College and the J. F. Pritchard and Co. conducted preliminary tests on the extrusion of anthracite silt at the Floridin Co. plant at Warren, Pa. Since that time these three organiza-tions—individually, together, and in cooperation with other interested groups— have actively pursued work on various phases of the problem. Much of the early history and details of the laboratory and pilot plant work by the Anthracite Institute, has been reported by Mulcey and Eckerd.2 It is the purpose of this paper to report additional information on the process, especially with respect to the factors influencing the quality and use properties of the product, and the current develop-

Jan 1, 1949

By Paul M. Tyler

YEAR after year, the kaolin industry of the United States has been setting new production records and making better products. High-grade paper, pottery, and rubber clays are produced in this country mostly in the South. Georgia alone contributes over 70 pct and South Carolina almost 20 pct of the total domestic output. Residual kaolin is mined in North Carolina, highly plastic but naturally sandy Tertiary (Eocene) potting clays are worked in north central Florida, and good white clays are produced in several other states, but the main sources of kaolin or china clay have been numerous deposits in the Tuscaloosa (Upper Cretaceous) formation. This formation of generally sandy sediments is called the Middendorf member in older geologic reports and corresponds in age with some of the New Jersey clays. As shown in fig. 1, it crops out almost continuously in a generally southwesterly direction across South Carolina and Georgia and into Alabama. Clay is mined from this formation in all three states but the principal producing centers lie within about 10 miles of a straight line drawn between Aiken, S. C., and a point about 10 miles south of Macon, Ga. The white kaolins of the South were recognized and used prior to the Civil War but suitable treatment processes were not introduced until World War I when imports, chiefly from England, were curtailed. Although imports of high-grade clays were resumed after 1918, the domestic industry managed to treble its prewar production record during the early 1920's and has continued to grow. Whereas the 1909 to 1913 average total production in the United States was only 132,104 short tons valued at $705,352 f.O.b. mines, the output in 1948 was 1,-568,848 tons worth $19,756,738. Paradoxically, it seems in retrospect that the early failure of the American industry to meet foreign competition was due to the superior quality of our sedimentary clays in their natural state. Kaolin, of course, is the principal decomposition product of feldspars which originate in acidic igneous rocks such as granite, aplite, alaskite, granodiorite, quartz porphyry, etc. English china clays occur in residual deposits and before they can be marketed they have to be treated to remove accompanying quartz, mica, and other impurities. Notwithstanding the relatively crude methods employed, the final product is a beneficiated clay which is subject to a certain amount of technical control as to quality and uniformity. Although the naturally concentrated deposits in Georgia and South Carolina contain some of the finest crude white kaolin in the world, even it can be made better by suitable treatment. In recent years well over half of the high-grade china clay produced in the United States has been used in making paper. Some qualities of paper clays are still produced by the dry process, or air flotation, but the paper industry's specifications have grown so exacting that wet processing was adopted and more refined methods had to be perfected. Notwithstanding notable advances in clay-preparation technology during the past decade, or possibly because these advances have implemented and encouraged technologic changes in consuming industries, demand has grown for products of higher uniform quality than can be obtained from even the best natural deposits without rigidly controlled fractionation. Largely as a result of the wide adoption of machine coating for paper, the clay industry has been obliged not merely to eliminate virtually all mineral impurities but also to segregate the clay substance itself into narrow particle-size ranges. By extraordinary coordination of sales effort and production technology, several Georgia companies manage to market a wide variety of specialized joint products but the commercial success of many producers depends upon their mining only the best parts of their deposits and then skimming the cream of this almost pure clay in order to obtain a maximum yield of kaolinite finer than about 2 microns in maximum particle size and possessing low viscosity as well as the more familiar attributes of suitable color and brightness, or reflectance. To the casual visitor from another mineral industry, the kaolin mines and plants may appear to be

Jan 1, 1951

By Walter Rose

In a recent technical note, Owen Thornton&apos; suggests that wetting liquid relative permeability may be derived from the relationship: where Pd/Pc is the ratio of displacement pressure to capillary pressure at the wetting liquid satdration Sw, and I is the resistivity index at this saturation. Thornton shows that this expression gives values for relative permeability in good agreement with those experimentally determined by Leverett. We have recently developed another expression for krw which seems preferable to Equation 1 since it requires fewer experimental data for its verification. This equation may be derived in the following manner. Making use of the analogy between mass transfer of fluid in a porous medium and electrical conductivity through the fluid in the same medium, we can postulate a hydraulic formation resistivity factor analogous to an electrical formation resistivity factor. From Poiseuille&apos;s Law the resistivity to flow in a tube of radius R is of the form 8u/R², where is the viscosity of the fluid. Similarly7 the resistivity to flow in a porous medium of the same dimensions as the tube is given by D&apos;Arcy&apos;s Law as where k is the permeability of the medium. The hydraulic formation resistivity factor, Ff, is thus the quotient of these two resistivities, or: But permeability is defined by the KO-zeny equation as: where: r is the average pore radius of the porous medium, L. is the average tortuous length of the average pore, + is the porosity, and L is the bed length. This gives Fr as a function of the (La/L) .-.-.tortuosity ratio and porosity, or in explicit form: where: T = (La/L)&apos;, and N is the number of pores of radius, r, which will be found in any cross sectional area, x R&apos;. That is, N = R²/r². It will be clear from the foregoing considerations that the hydraulic formation fat. tor should be dependent on the value of R which in every case must be arbitrarily selected. By analogy, the hydrauiic formation factor, Fcf, characterizing the porous medium at Sw<1,will be given by: R² NT. where ke is the effective wetting liquid permeability obtaining at Sw<l, and Te is the square of the (Las/L) ratio defined by Thornton. Therefore, the hydraulic resistivity index, If, is: However, Thrnton gives I as: and it follows that: Equation 2, when checked against the data of wyckoff and Botset² and some of the Morse et al data³, gives comparisons as shown at the bottom of this page. Computations based on Leverett&apos;s data, quoted by Thorntaon, gives computed krw values somewhat lower than the experimental values. Moreover, other instances can be cited where we find that neither Equation 1 nor Equa tion 2 is checked by experimental data. The work of Botset&apos; on the Nichols Buff sandstone and Morse et a1 on oil wetted Bradford sandstone are such instances. A reason for these discrepancies may lie in the fact that if both Equations 1 and 2 are presumed always to give accurate values for krw, it follows that PC = Pd/Sw". Such an expression, it is well known, is too simple to describe accurately the capillary pressure behavior of all porous media. However, it is believed that a particular advantage resides on the use of Equation 2, since it is not dependent for its utility on a knowledge of the capillary pressures obtaining in dynamic flow svsterns. No practical technique for measuring the capillary pressures characterizing the fluid distributions in dynamic flow systems has yet been proposed. Acknowledgment is given to Dr. Paul D. Foote, executive vice-president of the Gulf Research and Development Company, for permission to publish this note. 1. Owen F. Thornton, "A Note on the Valuation of Relative Permeability," J. Pet. Tech., 1:7, Section 1, July, 1949. 2. R. D. Wyckoff arid H. G. Botset, "The Flow of Gas-Liquid Mixtures through Porous Media," Physics, 7:325-345, 1936. 3. R. A. Morse, P: L. Terwilliger, .and S. T. Yuster, "Relative Permeability Measurements of Small Core Samples," Oil and Gas J., 46:109-125, Aug. 23, 1947. 4. H. G. Botset, "Flow of Gas-Liquid Mixtures Through Consolidated Sand," Trans. AIME, 136:91, 1940.

Jan 1, 1949

and would also contribute to the post-war employment. -As far as the future is concerned, I doubt whether any of the present geophysical methods will ever be developed to directly indicate ore. However, the geochemical methods and certain combinations between chemical and geological methods now used might be the answer to our prayers for direct and more definite methods of determining the quality of the ore or its relative metal content. Geochemical and spectrochemical analysis of minute content in ground waters, in soil or in plants and trees, living or dead, will be extremely important and I would venture to predict that in the very near future each mining or exploration company and each assay oflice will have its own spectroscope equipped for accurate chemical analysis, not only to guide the daily work in the mine, but also for identifying ores as well as for guiding exploration, geological mapping and the evaluation of geophysical indications. These methods, although they are still in their infancy, promise very much for the future. Radioactivity methods could also be helpful when sufficient facilities for radioactivity determination can be made available. They have already been used to a great extent in oil exploration and experiments have shomn great promise for ore exploration also. As for future surveys of large areas, the exploration for physical contrasts will be made from the air, using aeroplanes, helicopters, etc. Already electrical and magnetic methods have been designed whereby the instruments are carried in the aircraft and by automatic recording the location of anomalies is made in a simple enough manner. It should be possible in this way to cover, say, a square mile in an hour. Later Discussion Replies to Dr Lundberg. J. B. Macelwane.*—Someone has said that if a person knows his subject well enough he can explain it in words of one syllable. The point is well taken and I think the converse is also true. If a person cannot explain a subject clearly in simple words, it is either because he has not sufficient command of the language, or he is not master of his subject. Now it is obvious, it seems to me, that the remedy for both of these unfortunate conditions lies not in less education, but in more. If Dr. Lundberg has met geophysicists who confused and discouraged prospective clients by their inability to talk the language of the mine owner or of the mining engineer or geologist, the fault most probably lay in the geophysicist&apos;s lack of sufficient training; but it may also have been the want of ordinary common sense, which no amount of education can supply. It is hard to understand the position taken by Dr. Lundberg. Does he regret his own extensive training? noes he wish to say that he would have had greater success in geophysics if he had been only a mine hand with an instrument and a rule of thumb? As a matter of fact, I find it rather difficult to account for his presentation before this Committee on Geophysics of an emotionally distorted picture of the Report of the Committee on Geophysical Education, after the lapse of an entire year since the Report was read and discussed in its proper place, unless he honestly thinks he is handicapped by his knowledge and training and wishes to warn the whole profession against a similar fate. I regret that I am obliged to disagree so emphatically with Dr. Lundberg&apos;s thesis— but I believe it would be dangerous if left unchallenged, both because of the inaccurate statements it contains concerning the recommendations made in the Report and because of the ultimate discredit that would be bound to fall upon genuine geophysics if Dr. Lundberg&apos;s recommendations were extensively followed out. S. F. Kelly.*-—The argument that a science and its practitioners can be improved by debasing the standard of educational preparation is indeed a strange argument to come from the pen of a man with the education of Dr. Hans Lundberg. In criticising the Committee report, moreover, he has to a certain extent set up a straw man to belabor. The statement that the Committee report recommends that

Jan 1, 1946