Search Documents

By Gilbert Thiessen

The use of a pneumatic process for removing fine material (usually less than 48-mesh) is increasing in the preparation of stoker-size coal. The fine material, produced as a byproduct, is known as dedusting-plant dust. Since fusain is the most friable ingredient in bituminous coal (it may readily be rubbed to an impalpable powder with the fingers), it tends to accumulate in this byproduct. While studying the properties of cokes produced by blending Illinois coals with other materials, considerable quantities of fusain were required. Dedusting-plant dust suggested itself as a convenient supply. It became necessary, therefore, to determine how much fusain was contained in a measured sample of dust, how the fusain was distributed with respect to size and specific gravity in the sample, and whether or not it would be feasible or desirable further to concentrate or to recover the fusain from the dust before using it in the blends to be coked. The results obtained indicate the possibilities of production of a high-fusain material. Previous Work Lehmann and Stach have developed a processl,2 for separation of banded bituminous coals into their band ingredients by impact pulverization followed by screening or air separation. They found, as might be expected, that the fusain was concentrated in the very fine material. Prockat and Raute3 examined samples from dedusting plants operating in the Ruhr. They separated the dust into various screen sizes and determined the composition of each of these sizes in terms of the banded ingredients of the original coal. In the dusts examined by them, the finest material was always high in fusain, and most of the fusain contained in the original samples could be recovered from this fraction.

Jan 1, 1936

By C. P. Gazzara and

The modulus of elasticity and yield strength of commercially pure, annealed titanium sheet was investigated at room temperature as a function of strain rate and direction of loading. The value of E varied with direction of measuremeni in the sheet but was unaffected by strain rate in the range 0.04 x 10-to 10-2min-1. The yield strength increased with increase it2 strain rate and varied with specimen orientation. VALUES of the modulus of elasticity, E, in tension for commercially pure titanium have been reported at from 14 to 20Xl06 psi.' Reasons suggested for this variation have been a) composition, b) strain rate, c) texturing, and d) creep. For example, alloys of titanium with aluminum, manganese, and nitrogen have yielded modulus values of from 12.5 to 16.8 x lo6 psi at room temperature.' It was shown by Klier that the modulus in titanium plate was sensi-tive to strain rate. while Dotson and kattus meas- ured variations in E as the strain rate was increased from 3X to 60 min-l. For RC-7OA, 0.040-in. titanium sheet at room temperature Dotson and Kattus found that the average values of E, for specimens in the rolling direction, increased from 14.7 to 16.0 X lo6 psi as the strain rate increased. Simultaneously, the 0.2 pct yield strength increased from 74,700 to 95,700 psi for the same specimens. Differences in yield strength and E have been reported as a function of directionality in titanium sheet.= Dotson and Kattus report such an effect, and Feola6 found in annealed titanium sheet marked anisotropy in tensile strength, yield strength, reduction in area and elongation at room temperature, with

Jan 1, 1961

By Breaux B. Castleman

The ultimate test of a business strategy is whether it achieves the owner's objectives. Most shareholders are interested in growth and profits, and share values on stock exchanges are very often closely correlated with profit growth and profitability measured as return on equity (ROE). Strategic management, then, involves managing investments or resource allocations to optimize long-term growth and real return on equity, within reasonable limits of risk. Figure 1 shows a plot of the five year, weighted average ROE of a number of communications companies against their stock market valuations in 1983, measured as a ratio of market value to book value. The principal explanation of the differences in the relative valuations of the individual stocks is historical ROE, weighted toward the most recent years. Further analysis demonstrates the added importance of growth in explaining the differences in stock market to book ratios. [ ] Research conducted by Booz Allen and others in recent years suggests that the relationships between ROE and market to book multiples hold true in industry after industry. Furthermore, we have found that in assessing business strategies for companies in these industries, the analyses should focus on whether proposed strategies are likely to lead to consistent long-term growth in real ROE, without excessive leverage. Our research also reveals, however, that these approaches to strategy assessment are not consistently applicable in the natural resource extractive industries. Figure 2 shows a similar comparison of market to book values against five year average ROE for a group of nine mining companies in 1983. Market value of the shares shows little correlation with ROE. [ ] Analysis of the data for other extractive industries indicates a similar pattern; that is, low correlation between share values and

Jan 1, 1985

By John J. Reed

This paper was prepared as a supplement to the general review by Dr. N. G. W. Cook. His analysis of the problem in terms of the strain energy involved in making the excavation is excellent. It will contribute much towards a clearer understanding of rock behavior and control. Several of the practical applications described herein can be directly related to Dr. Cook's theories and conclusions, and are based on the very same principles. CONTROLLED BLASTING IN ROCK EXCAVATION Generally speaking, the natural rock is a relatively strong and competent structural material, if we conserve its inherent good properties and perhaps reinforce its weak spots. The difficulty often lies in blasting out the tunnel or chamber without damaging the walls and roof we wish to have remain afterwards. Much progress has been made in the last five years in better understanding the controlled excavation of rock. The specialized techniques known as smooth wall blasting and presplit blasting have now developed from the status of curiosities of rock excavation to the point where these techniques are specified in contracts drawn up for such rock excavation projects as tunnels, underground pourer houses, etc. These techniques have been well described and discussed in previous publications; there is no need to reiterate here. It might be well to point out that recent research has demonstrated the effect that inherent rock stress may have on presplitting in certain directions. Material can be presplit most readily parallel to the direction of maximum compressive stress, and this may not always be in the direction desired. Inherent rock stress measurements by stress relief over coring, etc., may have important value in deciding how to best presplit proposed excavations. In addition, recent work at the Colorado School of Mines has demonstrated the feasibility of con-

Jan 1, 1967

By Gilbert Thiessen

The use of a pneumatic process for removing fine material (usually less than 48-mesh) is increasing in the preparation of stoker-size coal. The fine material, produced as a byproduct, is known as dedusting-plant dust. Since fusain is the most friable ingredient in bituminous coal (it may readily be rubbed to an impalpable powder with the fingers), it tends to accumulate in this byproduct. While studying the properties of cokes produced by blending Illinois coals with other materials, considerable quantities of fusain were required. Dedusting-plant dust suggested itself as a convenient supply. It became necessary, therefore, to determine how much fusain was contained in a measured sample of dust, how the fusain was distributed with respect to size and specific gravity in the sample, and whether or not it would be feasible or desirable further to concentrate or to recover the fusain from the dust before using it in the blends to be coked. The results obtained indicate the possibilities of production of a high-fusain material. Previous Work Lehmann and Stach have developed a processl,2 for separation of banded bituminous coals into their band ingredients by impact pulverization followed by screening or air separation. They found, as might be expected, that the fusain was concentrated in the very fine material. Prockat and Raute3 examined samples from dedusting plants operating in the Ruhr. They separated the dust into various screen sizes and determined the composition of each of these sizes in terms of the banded ingredients of the original coal. In the dusts examined by them, the finest material was always high in fusain, and most of the fusain contained in the original samples could be recovered from this fraction.

Jan 1, 1936

By R. Raring, W. J. Harris, J. A. Rinebolt

G. W. Geil (National Bureau of Standards, Washington, D. C.)—The authors state that the degree of accuracy realized in the experimental determination of a, is likely rather low. This inaccuracy is attributed to the difficulty in reading the load of the tension machine at the instant of fracture of the test bars. I believe there is another factor which may have added considerably to the inaccuracy in the determination of a,, namely, the determination of 8,. Fracture of a cylindrical tensile specimen of a ductile metal tested in tension at room temperature is generally initiated at the axis and rapidly propagates radially to the periphery of the necked section. During the propagation of the fracture, the metal at the rim of the minimum cross-section extends longitudinally and contracts radially. Thus values of 81, based on diameter measurements made after complete fracture of the specimens do not necessarily represent the strain at the initial fracture." Data obtained at the National Bureau of Standards with a 0.3 pct C steel in the condition as-quenched from 1575°F and tempered at 1000°F for 1 hr and tested in tension at room temperature indicated a considerable "rim effect" and as shown in Fig. 13, resulted in an apparent increase in Sf from 0.90 to 0.98. As the fracture strain of this steel is approximately equal to those of the steels reported by the authors, it seems probable that a similar "rim effect" may have added to the inaccuracies in the reported values of Si and accompanying values of El. R. Raring (authors' reply)—The authors are grateful to Mr. Geil for having called attention to a possible source of uncertainty in the determination of fracture stress, and they are in agreement with the principles upon which his discussion is based.

Jan 1, 1952

By H. F. Yancey

THE jig may be termed the standard coal-washing machine. Although exact figures on the relative tonnages of coal treated by the various coal-cleaning processes are not available, it is known that a large part of all the coal given special cleaning treatment is handled by jigs. This wide use of the jig warrants a special study of its performance. In this paper are presented the results of an analysis of work done by a three-compartment jig in treating bituminous coal from the Thick Freeport bed in Allegheny County, Pa. Certain systems of washing coal require sizing before washing, while others treat unsized coal. The prevailing practice, however, for the preparation of coking coal from the more easily washed coal is to treat an unsized or natural feed at about -1 in. size and smaller. Under such conditions, the minimum size of particle that is beneficiated has long been and is still a matter of discussion and conjecture. In a careful laboratory investigation Jüngst1 concluded that the practical limit of settling of fine coal is reached at from 0.02 to 0.008 in. On the other hand, Hancock2 has found that single-compartment jigs, used in preparing coal for the domestic market, usually allow most of the heavy (refuse) particles smaller than 1/4 in. to go into the washed coal. He also states that it is impossible with the ordinary coal jig to make any noticeable improvement in the quality of the coal finer than 20 mesh (about 1/30 in.). Because of its importance in coal cleaning, the work described in this paper was undertaken for the purpose of obtaining information on this subject, as a part of the general coal beneficiation program being carried out by the Bureau of Mines.

Jan 4, 1925

By William M. Brewer

Until quite recently, in fact within the past two gears, but little attention has been given to the outcrops on the west coast of Vancouver Island, and their copper-contents. During the past few months the writer has been engaged in examining and developing some of these prospects. In many respects he has found characteristics associated with these prospects which, in his experience, are unique. In the first place, nearly all the outcroppings which overlie chalcopyrite-ore along the west coast of the island are composed of a high-grade magnetite. The magnetic qualities of some of these outcrops arc so pronounced that the magnetite possesses polarity. Although the writer hinlsclf had no analyses of this magnetite made, yet from its appearance he can readily believe that analyses made for other parties, which show a yield' of 62 or 63 per cent. of metallic iron, with only traces of phosphorus and silica, are correct. At a very shallow depth, masses of chalcopyrite, yielding in some instances as high as 32.6 per cent. of copper, occur associated with the magnetite; and in one instance, which recently came under the writer's observation, a solid body of high-grade chalcopyrite, fully 4 feet in thickness, occurs Within 6 feet of ; the surface. Usually this solid sulphide-ore carries low values in gold. Probably ail average of' $2 per toil would be fairly representative. But in some instances development has determined the occurrence of narrow stringers of pyritous quartz, associated with the sulphide-ores, which yield by assay more than $20 per ton in gold. In the districts examined by the writer, the country-rock is usually crystalline limestone, with dikes of igneous rock as intrusions. Sometimes the outcrops of magnetic iron-ore are

Jan 1, 1900

By J. Brian Eby

Contact metamorphism of coals is any physical or chemical change in the character of a coal directly attributable to heat of surface or intrusive igneous rocks. Coal beds so affected are found in the United States, England, Alaska, Mexico, New Zealand, Greenland, and other countries. Particularly in the United States, there is a wide occurrence of contact altered coals; conspicuous examples are found in Colorado, Utah, New Mexico, Illinois, and North Carolina. During a recent examination of coal beds on Yampa River, in northwestern Colorado, the author had an opportunity to make some detailed observations on the contact metamorphism of coals. In this field, coals over an area of 20 sq. mi. have been affected by dikes, sheets, and sills;' samples of the coals were systematically collected and analyzed,2 with the view of obtaining more specific data on the character of these alterations. The investigation was threefold in purpose: to secure information on the lateral effects of a dike cutting a coal bed, on the range in vertical effects on coal beds overlying sheets or sills, and on the range in the vertical effects on coal beds underlying sheets and sills. Favorable field conditions, such as fresh outcrops and newly dug prospects, made possible many of the field observations and collections. The coals studied in this field belong chiefly to the Mesaverde and 11Laramie" formations. The Mesaverde coals, on the average, are blocky low-rank bituminous coals; the "Laramie" coals, which are considerably younger, are of subbituminous rank. The coals of both formations, in the northeastern part of the Yampa field, have been greatly affected by basalt intrusives, yielding all variations of carbonized coal from natural coke to the unaffected material. The igneous rock that directly affects the coals is a fine-grained olivine basalt that is intruded, in sheets up to 200 ft. thick, into the coal-bearing

Jan 1, 1925

By Joseph Pogue

IT IS well known that one of the cornerstones of economic theory is the so-called law of supply and demand, which, really, is a group of economic laws, one of which may be succinctly stated : A rise in price tends, sooner or later, to increase supply. It is the fear that, in the case of petroleum, a limited natural resource, a point will soon be reached when supply will not respond adequately to price advances, which in recent years has prompted a movement for oil conservation. This movement has lately taken concrete shape in the appointment of a Federal Oil Conservation Board by the President. An important aspect of the law of supply and demand is that the supply of any commodity is not an entity per se, but is a factor of price. Supply, without the specification of price, has no exact meaning; and in practice supply cannot be divorced from considerations of price. Mathematically, supply may be expressed by the formula SP, which means that supply varies with price, just as the value of 10 raised to the x power varies with x. In its technical usage, supply is the quantity of a commodity that is bought currently on the market at a given price. In the case of a natural resource, however, this quantity will eventually depend not alone on price but on the physical volume of the reserve that exists and. that, in consequence, can respond to the stimulus of price. If this reserve is fixed in size, we must sooner or later reach a point where supply can no longer respond to price in the usual degree and a permanent shortage. will develop which no advance in price can correct, except in so far as higher prices may curtail demand or improve the efficiency of utilization.

Jan 3, 1925

By George Smith

TWELVE years ago, the Director of the United States Geological Survey addressed to the Secretary of the Interior a letter calling attention to the government's need for liquid fuel for naval use and pointing out that the rate of increase in demand was more rapid than the increase in production.1 This letter, in a way, inaugurated the policy of public oil-land withdrawals, which was well founded in its primary purpose of protecting the oil industry and highly desirable in its immediate effect of checking the over-development of that day in California. Unfortunately, however, through delays in legislation, this policy may be regarded now as having outlived both its intent and its usefulness. In 1908, the country's production of oil was 178,500,000 bbl., and there was a surplus above consumption of more than 20,000,000 bbl. available to go into storage.: In 1918, 10 years later, the oil wells of the United States yielded 356,000,000 bbl.-nearly twice the yield of 1908-but to meet the demands of the increased consumption more than 24,000,000 bbl. had to be drawn from storage. Nor is this all of the brief comparison. In 1918, our excess of imports over exports of crude petroleum was nearly 33,000,000 bbl. whereas in 1908 we exported 3,500,000 bbl., which was net, as we had not begun to import Mexican oil. In this period, the annual fuel-oil consumption of the railroads alone has increased from 16,871,000 to 36,714,000. bbl.; the annual gasoline production from 540,000,000 gal. to 3,500,000,000 gal. This record may be taken not only as justifying the earlier appeal for Federal action, but as warranting deliberate attention to the oil problem of today.

Jan 1, 1920

By C. P. Karr

FOR several years, the Bureau of Standards has been working in cooperation with an Advisory Committee on non-ferrous metals on various phases of the production and testing of zinc bronzes. The work has dealt, especially with the type of metal known as "Admiralty bronze" in England and as "Government bronze" in this country and consisting of 88 copper, 10 tin, and 2 zinc. Several reports have been made on this subject and these should be considered in connection with this paper.1 FIRST SERIES OF FIVE FOUNDRY TESTS A very brief summary of the first series of five foundry tests has been made,2 but for the sake of clearness the results are given here in different form. The five foundries cooperating in this investigation were: Ohio Brass Co., Mansfield, Ohio; Titanium Alloy Mfg. Co., Niagara Falls, N. Y.; Packard Motor Car Co., Syracuse, N. Y.; National Cash Register Co., Dayton, Ohio; Bureau of Standards, Washington, D. C. The object of the work was to determine whether uniform results could be obtained with this alloy in different foundries working under definite instructions. One of the participating foundries prepared, from virgin metal, a stock of ingots of the composition 88 copper, 10 tin, 2 zinc, and at the same time poured nine test bars from this melt of virgin metal. The results of the physical tests of these bars are shown in Table 1. Examination of this table shows that the highest and most nearly uniform results were obtained when the virgin metal was cast flat in chill molds and the lowest and most variable results were encountered when it was cast vertical in green-sand molds. In this, as in all other tables, the mean

Jan 9, 1919

By Campbell Hunter

PETROLEUM is found in almost every province in Persia. On the northern frontier, along the southern shore of the Caspian Sea, it is found near Anzelli and Shakhtesar and gas at Khoremabad. Oil is also found at Gumush Tepe, northwest of Astrabad, on the southeastern shore of the Caspian Sea. Further inland, to the south of Astrabad, oil is found at Schahkuh-i-balae, also on the margin of the Khorasan desert at Semnan, 115 mi. (35 m.) east of Teheran. Along the western frontier, from northwest to southeast, oil is encountered at Ouschachi, north of Lake Urumieh; in the province of Azerbaijan, at Zohab, Khanikin, and other places in the district of Kormanshah in the province, of Ardelan. Further south, in the province of Luristan, oil is found east of Mendeli and in the Pusht-i-kuh districts. Considerable quantities of oil are also obtained from Schuster, Maidan-i-Naphtun, Ram-Hormuz, Beheban, which are almost on a straight line, running northwest and southeast along the foothills of the Bakhtiari Mountains. At Ahwaz, in the province of Arabistan, oil has been found along another range of hills whose axis also lies in a northwest-southeast direction. In the Fars province, boring for oil has taken place at Daliki, and indications of oil are found at Kheri, Fasa, Darab, and other places. A gas show is also recorded at Kuhi-Sung-Atush in this province, 30 mi. (48 km.) east of Darab. In the south of Persia, oil is encountered on. Qishm Island, also at Ahmedi and other places north of Bunder Abbas. On the southeastern frontier, oil is found on the Sarhad range of hills. Thus, oil indications have been noted over a distance of approximately 1100 mi. along the western and 700 mi. along the northern frontiers of Persia.

Jan 2, 1920

By Richard J. Gowen

THE FUTURE The environment in which we live appears to change so slowly that most of us are unaware that any change has occurred at all. As the years pass, we notice increasing smog in our cities, new variations in weather, the shifting landscape with changing populations, and subtle but ever present alterations in the quality of life. In considering the future of our environment, we find we must grapple with questions concerning the very future of life as we know it today. Questions of resources, technology, society, governance, and purpose. Let us focus on the future of our environment and, in particular, raise the question of who is responsible for the environment. We know that action, or lack of action, will clearly influence our future environment. It is fashionable to catalog the many short-sightedness of our forefathers in developing the technologies which support the style of living to which we have become accustomed. However, I shall struggle to resist the temptation to list the well known ills of our present environment. Rather, let us concentrate on the future in our consideration of the priority of the multitude of options proposed to relieve our current energy crisis. We have recently witnessed the dramatic effects of air pollution produced by Mount St. Helen's eruptions. In the state of South Dakota, we watched our blue skies turn hazy and felt our eyes sting with the presence of volcanic ash. We were appalled at the dramatic effects on the landscape, crops, transportation, and all aspects of life in communities immediately downwind of the volcanic eruption. But in a few weeks, life had returned to near normal on the earth's surface leaving the volcanic ash in the atmosphere to ultimately

Jan 1, 1983

By Thomas Fraser, H. F. Yancey

The jig may be termed the standard coal-washing machine. Although exact figures on the relative tonnages of coal treated by the various coal-cleaning processes are not available, it is known that a large part of all the coal given special cleaning treatment is handled by jigs. This wide use of the jig warrants a special study of its performance. In this paper are presented the results of an analysis of work done by a three-compartment jig in treating bituminous coal from the Thick Freeport bed in Allegheny County, Pa. Certain systems of washing coal require sizing before washing, while others treat unsized coal. The prevailing practice, however, for the preparation of coking coal from the more easily washed coal is to treat an unsized or natural feed of about — 1 in. size and smaller. Under such conditions, the minimum size of particle that is beneficiated has long been and is still a matter of discussion and conjecture. In a careful laboratory investigation J?ngstl concluded that the practical limit of settling of fine coal is reached at from 0.02 to 0.008 in. On the other hand, Hancock2 has found that single-compartment jigs, used in preparing coal for the domestic market, usually allow most of the heavy (refuse) particles smaller than 1/4 in. to go into the washed coal. He also states that it is impossible with the ordinary coal jig to make any noticeable improvement in the quality of the coal finer than 20 mesh (about 1/30 in.). Because of its importance in coal cleaning, the work described in this paper was undertaken for the purpose of obtaining information on this subject, as a part of the general coal beneficiation program being carried out by the Bureau of Mines.

Jan 1, 1925

By H. M. Chance

Probably no other prosperous mining district is so little known as the Black Hills. The name leads one to assume that the district is a rolling country, consisting of more or less insignificant hills. Nothing could be more untrue, as the Black Hills is an elevated region rising to heights of 7000 and 8000 feet above sea-level, and broken by deep gorges and ravines. It is, in fact, a mountainous country in all that that term implies ; but the cañons and gorges are of such a character that the country is easily penetrated by railroad-lines, and good wdgon-roads exist to-day, affording access to every portion of it. Aside from the stampede to the Black Hills country in 1876, when gold-placers were discovered, and 15,000 or 20,000 people became infected with the mining fever, the region has never had a mining " boom." Quartz-mining commenced in 1877 or 1878, and has been successfully prosecuted ever since; the output of gold steadily growing, until at present the yield is about $7,000,000 annually. This great production is about equally divided between two entirely different classes of deposits. The first class, comprising the so-called quartz or free-milling ores (of which the Homestake mine is the principal producer), are veins of generally steep dip, in the older metamorphosed rocks, and similar to the veins worked in other mining districts. The second class of mines is located in what is known as the " siliceous gold-belt." The Siliceous Gold-Belt. This belt, more particularly to be described in this paper, lies in the immediate vicinity of Deadwood and Lead City, and covers an area 6 or 7 miles in length by 3 or 4 miles in width. The formation in which the siliceous ores are found is a nearly horizontal series of sandstones and shales, generally

Jan 1, 1901

By J. C. Jaeger

It frequently happens in engineering and mining situations that "bad" rock is encountered which consists of rock broken up into blocks a few inches or less in diameter by a network of intersecting joints. These joints may be open, or filled by veins of solid material, or covered with weathering products. Essentially, the material consists of an aggregate of small interlocking blocks. In such circumstances, major joint systems usually can be recognised and studied, but there are probably many minor planes of weakness which may cause the blocks to be of almost random shape. It is extremely difficult to determine the properties of such materials. Measurements on small specimens give the properties of the constituent rock and not the jointed material. At the other extreme, the material has occasionally been tested as loose aggregate in large triaxial pots, but this gives no information about the strengthening effect of the interlocking of the small blocks of rock. One simple approach, which has been much used, is to regard the rock as randomly jointed on a small scale and to apply soil mechanics theory to it. In this case, the normal and shear stress at failure are related by [ ] where the coefficient of friction p and the cohesion c will be those of the individual joints. Even in very bad rock, it is usually possible to drill core in small diameters of 1 to 2 in. which will contain a number of joints, both open and filled. The testing of such joints provides one simple method of determining some of the properties of closely jointed rock and will be discussed in detail in the next section. Calculations based on Eg. 1 with values of c and µ obtained in this way may be expected to give a lower limit for the strength of structures in rock.

Jan 1, 1970

By C. P. Karr

For several years, the Bureau of Standards has been working in cooperation with an Advisory Committee on non-ferrous metals on various phases of the production and testing of zinc bronzes. The work has dealt especially with the type of metal known as "Admiralty bronze" in England and as "Government bronze" in this country and consisting of 88 copper, 10 tin, and 2 zinc. Several reports have been made on this subject and these should be considered in connection with this paper.' First Series of Five Foundry Tests A very brief summary of the first series of five foundry tests has been made12 but for the sake of clearness the results are given here in different form. The five foundries cooperating in this investigation were: Ohio Brass Co., Mansfield, Ohio; Titanium Alloy Mfg. Co., Niagara Falls, N. Y.; Packard Motor Car Co., Detroit, Mich.; National Cash Register Co., Dayton, Ohio; Bureau of Standards, Washington, D. C. The object of the work was to determine whether uniform results could be obtained with this alloy in different foundries working under definite instructions. One of the participating foundries prepared, from virgin metal, a stock of ingots of the composition 88 copper, 10 tin, 2 zinc, and at the same time poured nine test bars from this melt of virgin metal. The results of the physical tests of these bars are shown in Table 1. Examination of this table shows that the highest and most nearly uniform results were obtained when the virgin metal was cast flat in chill molds and the lowest and- most variable results were encountered when it was cast, vertical in green-sand molds. In this, as in all other tables, the mean deviation was obtained by the usual method of taking the average of the differences of the individual values from the average values.

Jan 1, 1921

By H. F. Bishop, F. A. Brandt, W. S. Pellini

M. S. Fisher and D. R. F. West (Imperial College of Science and Technology, London, England)—It may be of value to compare certain features of the results recorded in this very interesting paper with those of an investigation11 involving determinations of temperature gradients and rates of solidification of steel blocks of 3 in. sq section, cast horizontally in sand molds, some of which contained chills. Castings in plain carbon steels containing up to 0.8 pct C were made and, throughout this range of compositions, both inverse-rate and direct cooling curves, obtained from thermocouples placed within the mold cavity, showed a major arrest, the temperature of which was taken as the "effective liquidus" for the particular steel in question, solidifying under the conditions of the investigation. At the completion of the arrest, the curves showed a comparatively rapid de- crease in temperature. Some of the steels investigated lay within the peritectic region, and a second arrest at 1485°C was detected. In Fig. 15, which shows the effective liquidus temperatures, the limit of the 8 + liquid field has been placed at approximately 0.5 pct C. In inverse-rate curves corresponding to the thermal center of each casting, there was always a discontinuity, viz: an abrupt change of slope, at a temperature about 10 to 20°C below the "liquidus arrest," after which there seemed to be no significant irregularity in the rate of cooling. Curves corresponding to other positions in the casting generally showed some irregularities below the main arrest, probably as a result of heat flow from the solidifying interior. Even the reproducible discontinuity in the curves for the central positions appeared to have no theoretical or practical significance, though it probably corresponded to a stage in the solidification process at which only a relatively small amount of interdendritic liquid remained. Its temperature, rela-

Jan 1, 1953

By C. Erb Wuensch

The Eagle mine is situated in the Kerber Creek mining district, Bonanza, Saguache County, Colo. The climate and topography of this district arc similar to those of mining camps of the Rocky Mountain region that lie 9000 to 12,000 ft. above sea level. The district is at the northeasterly edge of the San Juan volcanic region, in which successive Tertiary lavas have built up a high plateau resting upon earlier sedimentary formations, or the underlying pre-Cambrian complex. The latter was exposed in places by erosion previous to the eruptions. In the Bonanza district, proper, only volcanic formations, andesites and latites, are found. Dr. H. B. Patton,1 in his survey of the district, discriminates between several varieties of lavas and maps these as distinct flows. They are local variations within the same lava and it is impossible to determine any distinct line of demarkation between them. Structurally they are members of the same flow. There are three general types of vein occurrences: 1. Lead-zinc-copper-silver-gold veins in well-defined fissures with a quartz gangue; ill these, the various sulfides show a zonal arrangement. 2. Massive gray copper ores high in silver, in irregular fractures in the form of small lenses and pockets, in which little or no quartz is found. 3. Manganiferous quartz veins very low in silver and gold at the surface which, with depth, become important silver veins containing subordinate amounts of gold. These veins have a quartz gangue with an abundance of Phodochrosite. The silver is associated with small amounts of sphalerite, galena, and pyrite; fluorite also is present. The Eagle is the only mine that has been developed in the manganiferous quartz type of vein. It was discovered ill the fall of 1582, but little more than assessment work was done on the property for a number of

Jan 1, 1923