Search Documents

By T. G. Nilan

Steels containing 0.4 and 0.8 pet C have been transformed isothermally at pressures up to 34 kbuv. Decomposilion mechanisms are so intimately related to phase equilibvia that, as the equilibria shift under high pressure, the microstruclures of the decomposition producls change, maintaining at pressure the same correspondence between a given phase equilibrium and a given microstructure as a1 1 atm. A bainitic unicvo-structure occurs in these steels at high pressure that IS observed only at 1 aim abole 1.4 pct C. This strrrcl111,e 1s ruliorzalized in terms of the effect of pressure on the transformation to lower bainite. The pressuve depetlderlce of the kinetics of pearlile formation is descrihed by an absolute rule theory amalysis. The activation volume for the transformation is 7 cu cm per mlole, which is indicative of a phase-interface transformation-rate cotntrol mechanism. This fortmulation, when expressed in terms of known solule effects on the energelics of tvansformation, gives promise of explaining the effects of alloying elemenls on hnrden-abilily, particularly that of 'coball. KINETIC processes in solids are functions of the primary thermodynamic variables of state: composition, temperature, and pressure. Until the development of high-pressure techniques' that permitted the generation of sustained high pressure at high temperatures, metallurgical studies of such reactions were largely limited to isobaric conditions at atmospheric pressure. The data so obtained, and theoretical deductions based on these data, were necessarily incomplete For the particular case of austenite decomposition, a knowledge of the phenomenology of the reaction in terms of all the state variables should lead to a clarification of the process. This deeper understanding should facilitate a decision between conflicting theories that have been proposed to rationalize these phe- nomena. An analysis, derived from an understanding of the transformation mechanisms, may aid in the optimization of alloy steel development. The first studies of the effect of pressure on transformations in steel were made by Kulin et al. in 1952.' In a study of the influence of applied stress on mar-tensite formation in a 30 pct Ni steel, they found that the martensite start (M,) was depressed 8°C per kbar* by hydrostatic pressure. Jellinghaus and Friedewold3 were apparently the first to investigate the effect of pressure on isothermal transformations above the Ms. They found that the bainite transformation rate in a 1.2 pct C, 3.8 pct Mn steel was reduced by a factor of 3 by a hydrostatic pressure of 4 kbar. In both of these investigations,2,3 the M, of the steels studied was below room temperature. Austenitizing and quenching were done at atmospheric pressure, followed by the decomposition of the metastable austenite under pressure. The maximum temperature at pressure in the bainite study3 was 350°C. Until the advent of the present high-pressure devices, it was not possible to conduct isobaric high-pressure heat treatments from austenitizing through isothermal decomposition and quenching. The exploitation of high pressure as a variable in metallurgical studies was greatly advanced by the apparatus and techniques developed by Hall4 and co-workers. Utilizing these techniques, Radcliffe et a1.5 and Hilliard6 etermined the pressure dependence of phase equilibria in the Fe-C system. Hilliard and cahn7 examined the pearlite transformation rate in an AISI 1080 steel and also in a high-purity 0.92 C Fe-C alloy at 1 atm and at 34 kbar and found a 700-fold reduction in rate at pressure in the 1080 steel but only a fivefold reduction in the high-purity alloy. In agreement with the shift of phase equilibria under pressure, the microstructures were hypereutectoid at 34 kbar pressure, whereas they are eutectoid at 1 atm. Determination of the effect of pressure on carbon diffu-

Jan 1, 1968

By J. C. Bokros

At temperatures above 950°F, zirconium which has been strained a critical amount will experience critical recrystalli-zation. The large grain size thus formed can result in a reduction in the fatigue life by a factor of 2 to a factor of 9 at both high and low temperatures. The critical strains for zirconium vary from 15 pct at 900°F to about 2 pct at 1125°F, while those for zircaloy III vary from 15 pct at 1050°F to 5 pct at 1200°F. Zircaloy II ,experiences no critical recrystallization up to 1200°F. ZIRCONIUM has become increasingly important for nuclear applications and is being employed in reactors at temperatures where recrystallization can occur. Recent work' on the fatigue properties of zirconium has shown that coarse-grained structures developed in zirconium during recrystallization have much lower fatigue lives than fine-grained material. The development of these large grain sizes under such conditions is well known to be the result of critical recrystallization.2-4 Briefly, critical recrystallization occurs when a metal is strained a critical amount and annealed in the recrystallization range. The critical strain is defined as that minimum strain necessary to promote nucleation in the time unit and temperature considered. The maximum grain size occurs at the critical strain, since at this strain the fewest stable nuclei per unit volume grow into new grains. Recrystallization is not evident below this; strain since the nucleation rate is vanishingly lolw, and metal strained more than the critical amount has a higher nucleation rate per unit volume which results in a finer grained structure. This paper describes the critical recrystallization observed in reactor-grade zirconium, zircaloy 11, and zircaloy I11 as a function of annealing temperature and temperature of strain. EXPERIMENTAL The zirconium used was hafnium-free, double arc-melted sponge obtained from the Bureau of Mines. The ingots were forged and hot reduced to 0.08 to 0.10-in. sheet and subsequently cold reduced to 0.035-in. sheet with intermediate and final anneals at 1200 OF for 15 min. The zircaloy II and zircaloy III used were 0.035-in. sheets in the annealed condition. Compositions of these materials as tested are given in Table I. To determine the critical strain at a given temperature, tensile specimens having a0.065-in. taper in a 2-in. gage length were machined from the sheets parallel to the rolling direction. The specimens were polished, etched, and examined metallographically to ensure that all of them were strain-free, initially. Tukon indentations were made every half millimeter along the gage length of each specimen. These served as fiducial marks enabling the plastic strain to be measured with a microscope and micrometer stage. The specimens were pulled to failure at a rate of 0.002 in. per min in an Instron tensile-testing machine. Three temperatures were used for straining: room temperature, 500 ºF, and 900 ºF. The 500º and 900 ºF tests were run in an argon atmosphere. Since the rate of work hardening changes with temperature, a different critical strain was obtained for each temperature of strain. Specimens, prepared in the manner described, were annealed in vacuunl at various temperatures ranging from 900" to 1200 F for up to 1000 hr, after which they were examined metallographically. The critical strain and the recrystallized grain size as a function of strain were determined for each specimen. Results for the same temperature and time indicated that the critical strain measured was reproducible to within 5 pct of each other. RESULTS AND DISCUSSION Since increasing the time of anneal increases the probability of the nucleation of a new grain, the critical strain decreases with time at a decreasing

Jan 1, 1961

By David V. Ragone, James A. Craig, Richard E. Balzhiser

The Gibbs free energies of formation of UC2 and UC were measured by equilibrating two-phase mixtures of UC2 + C and UC, + UC with liquid bismuth. The measured equilibrium concentrations of uranium in the bismuth combined with available activity coefficient information yielded uranium activities in these two-phase regions. Measurements on UC2 were performed over the range 1015 to 1160 K and on UC over the range 1115° to 1165°K. The values obtained for UC2 are in excellent agveement with values determined using combustton calorimetry and low-temperature heat capacity measurements. The UC values are in fair agreement with the calorimetric values, differing by about 10 pct from the calorimetric determination. MUCH interest has been shown in the uranium carbides in recent years because of their potential as nuclear fuels. As nuclear reactor operating temperatures have been raised to increase thermal efficiency, new fuels have been required. The uranium carbides are of interest because of their high melting points, >2000°C, high thermal conductivity, and resistance to irradiation damage. The manufacture and use of uranium carbides are aided by a knowledge of their stability and reactivity under various conditions. In this regard the thermo-chemical properties of the carbides, i.e., heat capacity, heat of formation, free energy of formation, and so forth, are particularly important. A great amount of work has recently been done on the thermodynamics of the U-C system. Unfortunately, however, there has not been good agreement among the various investigations. This study of the free energies of formation of uranium monocarbide and uranium di-carbide in the temperature region 1100°-1200° K was undertaken to help clarify the situation. It should be noted that in the temperature range of this investigation, 1100°- 1200° K, the thermodynam-ically stable phase in equilibrium with graphite is U2C3, not UC2, Fig. 1. However, U2C3 is reported to be stable only under extremely low oxygen and nitrogen pressure. Although UC2 is metastable below 150O°C, it exists under most experimental conditions. It should also be noted that "UC," never exists as UC2 but with compositions near UC1.9. However, "UC2" will be used to designate the dicarbide phase except when the stoi-chiometry is necessary for clarity. METHOD The approach taken in this study of the free energies of formation of UC and UC2 was to determine the thermo- dynamic activities of uranium in the two-phase regions UC, + C and UC + UC, by equilibrating the two-phase mixtures with the liquid bismuth. When a mixture of solid UC2 + C is brought to equilibrium with liquid bismuth, the reaction that occurs is: Neither carbon nor UC, could be detected as dissolved material in the bismuth. The standard free energy for this reaction may be written: In the two-phase region UC, + C, Fig. 1, the thermo-dynamic activities of UC2 and carbon are unity. The activity of uranium in this region was determined by measuring the concentration of uranium in a liquid bismuth melt in equilibrium with the two-phase mixture. This concentration was then used in conjunction with the activity coefficient data of uranium in bismuth reported by Tien et al.' to determine the activity of uranium in the two-phase region, UC, + C. All of the quantities in Eq. [2] were then known, and the AG; (uc,) was evaluated. UC + UC2. For the studies involving UC + UC,, the reaction taking place when the two-phase mixture is brought to equilibrium with liquid bismuth is: The standard free-energy change for this reaction is given by:

Jan 1, 1969

By A. Rosen, P. Wynblatt, J. E. Dorn

The temperature, strain rate, and structure dependence of the flow stress in a poly crystalline Fe-2 pct Mn alloy was investigated between 77" and 370°K. It was possible to identify the low-temperature data from 77° to 160°K with Dorn and Rajnak's theory of the Peierls mechanism of plastic deformation. Above 160°K one or more thermally activated mechanisms must he operative; however, these were not identified in this investigation. The mechanistic basis for the rapid decrease in the flow stress of bcc metals with an increase in temperature over the low-temperature range is yet being debated. Various dislocation mechanisms have been suggested in the past but the agreement between the various proposed theories and the experimental results have not been definitive. In the present paper, the authors will demonstrate that the plastic behavior of polycrystalline iron containing 2 wt pct Mn plus interstitials agrees excellently with predictions based on the Peierls mechanism from 77" to 160°K whereas from 160" to about 370°K other as yet unidentified thermally activated mechanisms take over. Undoubtedly, the overlap of these mechanisms with the Peierls mechanism contributed to the difficulties of rationalizing the low-temperature behavior of iron and its alloys. I) EXPERIMENTAL TECHNIQUES AND RESULTS Although extensive data are now available on the effect of temperature and strain rate on the flow stress of various bcc metals and alloys, it was, nevertheless, deemed necessary for the objectives of the present study to obtain highly accurate data of the type most pertinent for checking the theories on a series of well-documented work-hardened states. Iron containing 2 wt pct Mn was used in this investigation in order to obtain a lower ductile to brittle transition temperature than that for iron.' The additional elements present were 0.004 pct C, 0.05 pct 0, 0.004 pct S, 0.003 pct P, 0.006 pct N, and 0.001 pct Si. The as-received 3/8 by 3/4 in. bars were cold-rolled to 0.100-in. thickness, recrystallized under argon for 30 min at 1073"~, further cold-rolled to 0.063-in. thickness, and finally recrystallized under argon for 30 min at 1000°K. This treatment gave a stable reproducible equiaxed grain structure having an average grain diameter of about 90 p. Prior to the final recrystallization treatment, the sheet was machined into tensile specimens 1/4 in. wide having a 1.625-in.-long gage section. All specimens were tested in controlled-temperature baths on an Instron Testing Machine. For convenience in the theoretical analyses the data will be given in terms of the shear stress for flow, 7, the shear strain rate, f, and the shear strain, y. A series of three standard strain-hardened states were obtained by prestraining specimens at 300°K and at a shear strain rate of 7.68 x lo-' per sec to three stress levels of 6.89 X l08, 10.3 X lo8, and 14.5 x 10' dynes per sq cm, respectively. Immediately following this prestrain the temperature bath was changed and each specimen was pulled in tension at either f = 7.68 X lo-' or f = 3.06 X 10"3 per sec. In terms of the accuracy that was achieved, the values obtained did not deviate more than *0.1 X 10' dynes per sq cm and * 1°K from the reported values of stress and temperature and not more than *5 pct in the reported values of the strain rate. The tensile stresses were converted to shear stresses using a factor of 1/2. The shear stress for the initiation of flow at the test temperature was determined by taking a y = 6.16 x 10'3 offset. from the modulus line at which point good accuracy could be achieved in determining y and the associated flow stress 7, with only a negligible increase in the pre-

Jan 1, 1965

By R. G. Knickerbocker, W. E. Brown, G. J. Vahrenkamp, M. M. Fine

THE results of a research and development laboratory and pilot-plant mineral-dressing investigation by the Bureau of Mines of the complex copper-lead-cobalt-nickel ores of southeast Missouri are reported in this paper. This investigation, in cooperation with the National Lead Co., showed that separate concentrates of lead, copper, and cobalt-nickel could be made by fine grinding and flotation. An industrial plant built subsequently by the St. Louis Smelting and Refining Div. near Fredericktown, Madison County, Mo., produced such concentrates during the war years. Present commercial production at the mill is limited to lead and copper concentrates, but research to permit economic utilization of the cobalt and nickel values is continuing. The complex sulphide deposits near Frederick-town in Madison County, Mo., have an operating history that dates back to the years preceding the Civil War. Perhaps these operations can best be summarized in terms of output which are given by Tyler: "Previous to 1900, the Mine la Motte Co. shipped cobalt ore to Swansea and in 1903 produced 120,000 pounds of oxide in a Missouri plant. Another cobalt refinery erected in 1906 by the North America Lead Co. at Fredericktown, Mo., operated intermittently until 1910. In 1909 it produced 83,384 pounds of cobalt oxide, 328,403 pounds of nickel, 8,314 tons of nickel-cobalt concentrates, 600 tons of copper concentrates, and 1,353 tons of lead concentrates. This plant was purchased at a forced sale in 1915 by the Missouri Cobalt Co., which produced a certain amount of oxide in 1918 and in 1920 recovered 102,410 pounds of cobalt oxide and cobalt hydrate, valued at $262,810." According to Buehler,2 "The ore, which consists of a complex mixture of the sulphides of cobalt, nickel, copper, lead, and iron, occurs at the contact of the pre-Cambrian porphyry and the overlying Lamotte sandstone and Bonneterre dolomite." The source of most of the cobalt and nickel is siegenite, a member of the linnaetite series of minerals. Its composition is variable, and although the chemical formula may be given as (CoNi),S,, it usually contains both iron and copper. The siegenite is characterized in this instance by an intimate association with chalcopyrite, and to a lesser extent with iron sulphides. Galena, on the other hand, while dis- seminated throughout the ore, is not closely bound to other constituents. Gangue is composed essentially of dolomite and quartz. Petrographic examination showed that fair liberation of sulphides and gangue could be attained at — 100 mesh. Complete liberation of micronsize inclusions, particularly of sulphides in each other would not have been possible at —400 mesh. Beneficiation Studies Many samples of the southeast Missouri ore were tested, but most of the work was confined to five samples of churn drill cuttings weighing 15 tons. The samples were reportedly representative of five sections of the deposit and were tested individually and as a composite. Only the results of the tests on the composite, which contained 1.28 pct lead, 2.03 pct copper, 1.06 pct nickel, 0.87 pct cobalt, 3.57 pct iron, 15.4 pct lime, and 23.9 pct silica, are presented in this report. In view of the rather complex and intimate association in the mineralogical composition of the ore, flotation was the logical choice in the selection of a beneficiation process. Other mineral dressing unit operations were considered as an adjunct to flotation, but none were beneficial. Many tests were made on these samples to determine the flotation characteristics of the mineral siegenite. As a result of this work, it was noted the siegenite was intermediate in floatability between chalcopyrite and galena on one extreme and iron sulphides on the other. The difference in floatability between siegenite and the iron sulphides was not very great and, in general, the same reagents that depressed pyrite and marcasite would also, in slightly larger quantities, depress siegenite. This tendency for siegenite

Jan 1, 1952

By E. T. Hayes, A. H. Roberson, M. H. Davies

ZIRCONIUM has been produced on a pilot-plant scale for only a few years, but the potential uses have led a large number of research establishments to engage in a thorough study of the metal and its alloys. The work described in this paper is part of a cooperative project between the Bureau of Mines and the Air Materiel Command. The Zr-Cr system was one of the first investigated because of the possibilities of improving the properties at elevated temperatures, the chemical corrosion resistance, and the mechanical properties of zirconium in a manner similar to the enhancement of the properties of titanium by additions of chromium. There is no published work on the Zr-Cr system but from the similarity of the metals involved it was expected that it would be similar to the Zr-Fe' and Ti-Cr' systems. The materials used in this investigation were prepared in the Bureau of Mines laboratory at Albany, Ore. Zirconium was produced by magnesium reduction of zirconium tetrachloride, and a typical analysis is as follows: Fe, 0.06 pct; Ox, 0.08; N?, 0.01; C, 0.02; and other impurities such as Al, Pb, Ni, Ti, and Si less than 0.01 pct each. High purity chromium was prepared by treating crushed electrolytic chromium in a stream of dried and purified hydrogen." The resulting powder contained about 0.01 pct 0 and about 0.1 pct total metallic impurities. All alloys were prepared by arc-melting 50 g briquetted compacts of the desired composition in a Kroll-type" arc furnace using an inert atmosphere. The furnace was evacuated twice and backfilled with helium, which was gettered by melting a center zirconium button immediately before the alloys were melted. Alloys were remelted at least once to insure greater uniformity of composition and subsequently were annealed in vacuum at 1250°C for 48 hr. Fairly homogeneous alloys were obtained by this means; a slight loss of chromium from the surface by evaporation during the high temperature homogenization was noted. All alloys were analyzed for chromium and gave results in good agreement with the nominal composition. Spot checks on tungsten and nitrogen showed pick-up of these elements to be negligible. Over 70 alloys were prepared for use in this investigation; only the critical ones are shown in Table I. Alloys containing up to 10 pct Cr were amenable to hot working at 850°C and a number of these were sheath rolled to 1/16 in. thickness. Specimens were cut from the sheet for use as metallographic samples. For the thermal analysis a differential couple was used in conjunction with an X-Y recorder, the temperature of the specimen and the difference in ternperature between it and the standard nickel body were recorded simultaneously. Heating and cooling rates of 5°C per min were used. The sensitivity of the instrument was such that a difference in temperature between the specimen and standard equivalent to 0.1 mv produced a deflection of 1 in. on the recording chart. The chromel-alumel thermocouples were checked against a Bureau of Standards calibrated thermocouple. Melting-point determinations were made in a high vacuum induction furnace using an optical pyrometer. The pyrometer, calibrated against nickel, copper, and zirconium (iodide process) under near black body conditions, was focused on the base of a hole drilled in cylindrical samples. A North American Philips Geiger counter X-ray spectrometer was used for all diffraction studies. This instrument, in addition to supplying precise intensity measurements of planar reflections, has an added advantage in that metallographic specimens mounted in bakelite can be used directly, and this

Jan 1, 1953

By R. J. Lloyd

INTRODUCTION The Mount Isa Mine is a large modern underground mine located in North-Western Queensland, Australia. Two ore types are mined and treated separately. Currently silver-lead-zinc ore is mined at the rate of 2.6 million tonnes per annum and copper ore at the rate of 4.6 million tonnes per annum. The silver-lead-zinc orebodies are mined by sub level open stoping and cut and fill methods whilst all copper ore is extracted by various forms of sub level open stoping. The mining operations are highly mechanised and utilise diesel powered load-haul-dump units of various sizes, two and three boom face drilling jumbos, electric-hydraulic rotary-percussive ring drills, in-the-hole hammer drills, rotary blasthole drills, raiseborers, battery/trolley locomotives, a large fleet of rubber tyred service and supply vehicles plus light rockdrills mounted on airlegs, rail mounted overshot shovels and battery and diesel powered locomotives. All stoping production ore is extracted with diesel powered load-haul-dump units. The ore is tipped into orepasses which connect to the main rail haulage levels. On the haulage levels electric battery/trolley locomotives are used to pull rakes of bottom dump or side dump trucks which feed the ore into primary crushers. Following two stage crushing the ore is conveyed to the shaft and hoistod to surface in bottom dump skips. Each ore stream has its own rail transport system, crushing stations and hoisting shaft feeding separate concentrators. This paper will consider some aspects of the role of equipment and machinery in the growth of the mine, will discuss in some detail the machinery and equipment in use today and will conclude with a look at some possible developments in mining equipment for the future, with particular reference to the Mount Isa Mine. A summary of mining equipment in use at Mount Isa is given in the Appendix. THE PAST Silver-lead-zinc ore was discovered at Mount Isa in 1923 and within a very short time many small mines were being developed. However the rich surface ore traces did not continue and by 1928 Mount Isa Mines Limited had acquired sufficient leases to plan for a large scale mine to exploit the low grade orebodies. At this early stage it was recognised that the mine would need to adopt the most mechanised mining techniques then available in order to overcome its twin disadvantages of low graaes and extreme remoteness. The Company introduced bar mounted drifters and overshot shovels to replace hammer and tap and hand shovelling in development work and by 1930 headings were advancing at the rate of 30 metres per week. In keeping with the concept of mechanisation the early engineers designed the Man and Supply shaft with a very large, for those days, cage compartment measuring 3.8 m x 3.4 m. This shaft was the main means of access into the mine for 36 years until the K57 shaft (now R62 shaft) was commissioned in 1966. Man and Supply is still in regular use. Production commenced in 1931 at an annual rate of approximately 660 000 tonnes of silver-lead-zinc ore. The mine was mechanised to an extent which was previously unknown in Australia; whilst the concentrator, smelter and power house utilised the most modern and efficient equipment available. Even so, the mine was very near to closure on several occasions and did not return a dividend to its shareholders for many years. Production levels remained at or slightly below 660 000 tonnes until a separate copper ore streani and mill was commissioned in 1953, doubling the existing production levels. The first underground crushers were installed at this time. Production rates expanded in the years between 1953 and 1973. By 1960 production reached 2740 000 tonnes of ore. In 1965-66 total production was 3650 000 tonnes and in 1973 the production rate plateaued at the current level.

Jan 1, 1981

By J. Chipman, N. J. Grant, E. C. Roberts

An equilibrium study was made of the distribution of chromium and oxygen between liquid iron, containing less than 1 pct Cr, and simple slags of the CaO(MgO)-Si02-FeO-Cr& type in the temperature range 1526' to 1734OC. The effects of slag oxidation, temperature, and basicity were observed. IN spite of the fact that chromium is one of the most important alloying elements in steel, and exists in almost all steels as a significant residual element, little research has been done to determine its behavior in basic steelmaking processes. Considerably more work has been done under silica-saturated acid slag conditions. Korber and Oelsen,' Herasymenko,' and others have generally agreed that in acid steelmaking practice the chromium in the slag behaved as if it were present as the chrom-ous ion (CrO). Work by Hilty- ir, high chromium slags also indicated that chromium may exist as CrO. In basic slag systems no equilibrium data exist. Based on individual studies of basic open hearth and electric furnace practice, Bardenheuer," Rock-rohr,% nd HauckQ oncluded that: 1—chromium recovery increased with decreasing basicity, and 2— chromium recovery increased with increasing temperature, although the effect was small. In similar studies Yavioskii and Dzemyen' concluded that: 1— slag FeO is the most important variable, 2—the basicity of the slag has no effect on chromium recovery, and 3—slag viscosity is not high even when 20 pct Cr,O, is present. Lapitskii\ oncluded that chromium recovery improved as the basicity of the slag decreased and increased with increasing manganese in the metal. Regarding the effectiveness of CrZ08 as a base or acid in basic slags, both Kristofferseno and Trojer" reported that Cr,08 was an acidic component requiring neutralization as 2CaO-Cr,O,. Experimental Procedure The experimental apparatus and procedure used for the present research were similar in most details to those used by Winkler and Chipman" and were described in detail by them. A magnesia crucible was used, holding 60 to 80 lb of Armco iron which was decarburized with hydrogen to about 0.010 pct C. Since all the metal samples solidified without gas evolution, this carbon level was assumed not to be significant. Synthetic slags made by mixing pure oxides were used throughout the study. Temperatures were measured by means of calibrated W-Mo thermocouples and were checked by Pt-Pt-Rh thermocouples. The range of temperatures covered in this study was from 1526" to 1734°C. The chromium content of the iron was in the range 0.032 to 0.82 pct, although the bulk of the tests showed 0.04 to 0.2 pct. The slags were of the CaO(MgO)-SiO,-FeO-Cr,O, type in which the Cr,O, content was from about 2 to 20 pct, although most of the slags showed from about 2 to 10 pct. The FeO range was from about 10 to 65 pct. CaO and SiO, were in the range of about 5 to 45 pct each, yielding a rather wide range of basicity values. The first 12 heats were made without a sulphur addition, and with only 30 min allowed for slag-metal equilibrium to be reached. In previous research it had been shown that less than 30 min was adequate to achieve equilibrium in slags free of Cr2O8.11,14.15 A study of the present data indicated that some of the tests may not have reached equilibrium in this time; accordingly four additional heats were made in which at least 1 hr was permitted for equilibrium to be reached. For reaching

Jan 1, 1955

By A. F. Colombo, R. T. Sorensen, D. W. Frommer

An analytical method has been developed and used in batch and continuous tests to provide initial insights into the effect of soluble calcium ion in anionic flotation of silica from iron ores. A deficiency or excess of calcium ion in pulps subjected to this type of flotation produces an impairment in flotation efficiency. Data developed in the investigation are from a single ore, but show that total calcium requirement is met from water, ore and reagent sources. In batch studies, starch additions were shown to exert no influence on the calcium level, but fatty acid and sodium hydroxide had subtractive effects. The investigation was next extended to continuous flotation testing where the general observations from batch testing were confirmed. Factorially designed experiments were performed showing that the relationship of calcium additions to flotation response was not a simple one, but tended to shift to higher additions with increased fatty acid. Nevertheless, the range of soluble calcium levels measured remained fairly constant in areas of good flotation response. It is concluded that techniques developed should be useful in removing empiricism from flotation operations in this and other systems requiring activation for success. Further development should aid in process control both through methods outlined and through investigations aimed at studying the effects of other soluble reagents. Of the major mineral commodities, iron ore was one of the last to succumb to flotation processing. Commenting on this fact, one of the speakers 1 at the convention celebrating the 50th Anniversary of flotation in the U.S.A., said ". . . in 1951 froth flotation as a means of beneficiating nonferrous minerals was a might giant and could be characterized by 'you name it, we float' - but not iron ore". This tardiness in applying flotation to iron ores was the result of a number of factors, including economics and ready availability of direct shipping ores. Even now, when the need for beneficiation can no longer be denied, proposals for flotation of iron ores are apt to be viewed with some misgivings. This disquiet results from knowledge that wide variability, which would necessitate corresponding adjustments in reagents, often exist within even a single ore deposit. Coupled with ore variability is the fact that, at present, there is no way of quickly and precisely anticipating the direction and magnitude of reagent changes required for uninterrupted production of acceptable concentrates. Despite the long delay, iron ore flotation is now practiced commercially, although the chief applications2-4 are to specular hematites having relatively coarse liberation and low slime content. In addition, the application of flotation in upgrading magnetic concentrates seems assured. However, these flotation methods do not appear applicable to substantial tonnages of fine grained, earthy, and frequently more complex semitaconites and nonmagnetic taconites. The U.S. Bureau of Mines, in devoting its attention to the semitaconite and nonmagnetic taconite class of materials, has demonstrated that anionic flotation of calcium-activated silica can be utilized with an expected high frequency of success.' Even so, it has been recognized that the flotation method is a complex one, and that the reagent suite must be carefully tailored to the feed. These conditions would be expected to offer difficulties in treating ores with the wide range of variability previously discussed. Accordingly, research was initiated to develop methods to remove much of the empiricism from the flotation operation by measuring the reagent variables within the pulp for a correlation with flotation response. A simple illustration of the technique sought would be in the well established use of pH meters to provide feedback control to reagent feeders and thereby limit acidity or alkalinity to a range producing optimum results. The first efforts in this area have been concerned with measurements of soluble calcium ion. Bureau experience in both laboratory and pilot plant over the past five years has proved that the amount of calcium

Jan 1, 1965

By B. F. Decker, J. H. Keeler, W. R. Hibbard

Textures of hot-rolled, of cold-rolled, and of cold-rolled and annealed zirconium sheets were determined by use of an X-ray spectrogoniometer. All textures showed a tilt of the basal planes 240" from the rolling plane about the rolling direction. Deformation textures showed the [1010] direction to be approximately in the rolling direction. After recrystalliza-tion, the 111201 direction was approximately in the rolling direction. This texture was sharpened by annealing above the allotropic transformation. Textures of sheet produced by alternately cold rolling and then annealing were less strongly oriented than sheets that underwent severe deformation without intermediate anneals. THIS study of the deformation and annealing textures of high purity zirconium was carried out to supplement an investigation of zirconium and zirconium-base alloys. The spectrogoniometer method of pole figure determination was used and yielded more detailed and precise information than the photographic techniques used by previous investigators. Earlier investigations of the rolling textures of hexagonal metals titanium,1,2 beryllium," and zirconiumL having a c/a ratio slightly less than 1.6 disclosed a rotation of the basal planes from the rolling plane about the rolling direction so that the basal poles were inclined toward the transverse direction, and with one exception,& the [1010] direction was found parallel to the rolling direction. Similarly, hot rolling produced a spread of the basal poles in the transverse direction,2,3,5 With the [1010] direction parallel to the rolling direction. The textures of these metals after recrystallization differ somewhat from each other although still exhibiting the transverse rotation of the basal poles about the rolling direction. Zirconium" was found to have the [1120] direction in the rolling direction, beryllium" continued to have the [1010] direction in the rolling direction, and titanium' was shown to have the [1010] direction in the rolling direction (the cold-rolling texture) when annealed at 1000°F, changing to the [1120] direction in the rolling direction when annealed at 1500°F. It was suggested2 that the titanium retains the deformation texture after re-crystallization, and preferred grain growth at higher temperatures produces the second texture. Annealing above the allotropic transformation temperature did not appreciably change the high temperature recrystallization texture for titanium.' Coarsegrained zirconium showed more spread" in the transformation texture than in the recrystallization texture. The material used in this investigation was crystal-bar zirconium prepared by the iodide process. The major impurity was hafnium which was less than 0.3 pct. The composition obtained by spectro-graphic analysis is given in Table I. The hot-rolled specimen was prepared from a 50-g button of zirconium arc-melted in a water-cooled crucible under an argon atmosphere. This button was enclosed in a welded sheath of soft iron and the ensemble was rolled at 825°C. After each pass the sheath was put back into the furnace to allow it to return to the desired temperature. The zirconium ingot was reduced in this manner to a thickness of about 0.035 in., a reduction of approximately 90 pct. The sheet after removal from the sheath was alternately polished and etched to a thickness of 0.001 in. Cold-rolled specimens were prepared from crystal bar by a series of reductions of approximately 0.010 in. until the sheet reached a thickness of 0.010 in. after which it was cold-rolled to 0.001 in. thickness between sheets of alloy steel. The total cold reduction amounted to about 99.8 pct. Specimens were annealed in an evacuated Vycor or quartz tube. The transmission pole figures were obtained by the quantitative method of Decker, Asp, and Harker6 modified by Geisler7 using an X-ray spectrogoniometer with Cu Ka radiation. Unless otherwise specified all four quadrants were examined with 5" increments along the radius of the pole figure. Absorption corrections were made for changes in length of the X-ray path through the sample as inclination of the

Jan 1, 1954

By Milton Williams

A comparison is made between the amount of interstitial water found by analysis in cores and that estimated from the resistivity curve of the electric log for the corresponding strata of producing reservoirs. It is shown that while the determined and the estimated water saturations are in good agreement in some cases, this agreement may be due to a fortuitous compensation of errors. Estimates of water saturations made from the electric 1og by use of existing relations should, therefore, be employed with caution. Also presented are data on the variation of salinity of interstitial waters in reservoir sands, and on the effect of variation of salinity and porosity on the validity of estimates of water content made from the electric log. INTRODUCTION Throughout the history of electric logging there have been recurrent cycles of optimism and pessimism as to the value of the electric log in the quantitative estimation of reservoir fluid content. The very early days of electric logging were an optimistic period, in which there was widespread faith in the ability of the resistivity curve to reflect fluid content, and in the ability of the potential curve to indicate textural characteristics. In time the accumulation of exceptions to this idealistic behavior brought about a general disillusionment, and caused the more pessimistic of those dealing with electric logs to believe that the sole importance of the log lay in stratigraphic correlation. Within the last several years optimism as to the quantitative use of the electric log has been revived, primarily as the result of the stimulating work of C. E. Archie' on the estimation of interstitial water in sands from resistivity data. Even though the general trend of thought on the quantitative value of the electric log reflects optimism, it is inevitable that there are some widely divergent opinions of the validity of quantitative estimates based on the electric log. A valid method of estimation of fluid content by means of the electric log and a general knowledge of the textural character of the reservoir rock would be of signal importance, not only in that it would save time and money in securing information on reservoirs now being drilled, but also because it would permit the evaluation of reserves in many fields drilled without adequate core data subsequent to the advent of electric logging. Because of this importance, Humble's Production Research Division, in cooperation with various other company divisions, initiated several years ago series of tests designed to evaluate the reliability of estimates of fluid content made from the electric log. The investigation was limited at the outset to sand reservoirs, since it was felt that the inclusion of limestone reservoirs would entail needless complications. In devising these tests it was immediately apparent that the chief difficulty in evaluating the worth of any method of estimation lay in establishing the true value of fluid content. The results of direct analyses of cores cut with ordinary mud were not sufficient, because of the probability of contamination of the fluids by filtrate from the drilling mud; the results of restored state tests on cores were deemed unsuitable because these results can hardly be said to furnish a primary standard. The method adopted was the direct analysis of cores cut with an oil-base drilling fluid. Such cores, when properly handled, are believed to afford the most precise determination of water content available at the present, and, in addition, lend themselves readily to the determination of various other properties which are pertinent to the estimation of fluid content from the electric log. Since it was desired to compare the fluid contents estimated from the electric log run in ordinary mud with cores cut in the same hole, the use of oil-base fluid necessitated the changing over, after all cores were cut, to a conventional mud. This procedure presented several advantages, one of which was that the use of oil-base fluid permitted

Jan 1, 1950

By F. V. Lenel

Resistance sintering under pressure is a method of hot pressing in which a powder compact is subjected to pressure and simultaneously heated by passing a low voltage high amperage current through it. Equipment for this process is described. Its basic characteristics such as resistance requirements for powders and compacts, temperature distribution in compacts, and gas reactions during resistance sintering are discussed. Examples of the sintering process in compacts made of a single metal or an alloy powder and in compacts made of mixtures of powders are presented. Potential commercial applications of the process are evaluated. THE usual sequence of operations in commercial powder metallurgy is to compact metal powders in a die at room temperature and sinter the compact subsequently without applying pressure while the compact is in the sintering furnaces. In hot pressing, on the other hand, the compacting and the sintering are combined. The loose powder, or in many cases a cold formed compact, is inserted into the die which is held at the hot pressing temperature, the compact is left in the die until it attains its temperature, and then pressure is applied and maintained for a given length of time. The die may be heated by surrounding it with a suitable furnace, by high frequency induction heating, or by passing current through the die. In hot pressing, compacts of high density and good mechanical properties can be produced in a relatively short time. One of the principal difficulties in hot pressing is the lack of suitable die materials which will have adequate strength at the hot pressing temperature. This difficulty can be overcome at least partially by heating only the material to be hot pressed without heating the die directly. This can be done by passing a low voltage high amperage current through the material and simultaneously subjecting it to pressure. Either loose powders or compacts can be hot pressed by this method in which the desired temperature is produced by the power dissipated in the metal powder. This method of hot pressing has been termed "electrical resistance sintering under pressure." The most significant differences between this operation and conventional hot pressing are: 1—The sintering times are very short, usually a fraction of a second and at most a few seconds. 2—The powder and die are initially cold. 3—Heat is generated within the powder itself and not conducted in from the die. 4— The pressure used is high. 5—Cooling following sintering is rapid, amounting to a quench. Resistance sintering of metal powders under pressure has been suggested repeatedly. In 1933, G. F. Taylor' proposed an apparatus which consisted of an insulating tube made of glass, or a ceramic filled with the powder to be pressed, and plungers above and below the powder. The powder was to be heated by passing an electric current through it and pressure was then applied. The apparatus was intended principally for hot pressing cemented carbides. Although the principle of resistance sintering under pressure is clearly shown in this patent, few details are given. A sintering period of a second or a fraction of a second, which is terminated by the operation of an inertia switch, is mentioned but no values for current density are mentioned. Low pressures, such as atmospheric pressure or a somewhat higher pressure exerted through a lever, are suggested. W. D. Jones' discussed electrical resistance sintering under pressure and proposed using resistance welding apparatus for this purpose. In a patent issued in 1944, G. D. Cremera described a method of electrical resistance sintering under pressure using resistance welding apparatus which was to be applied mostly to nonferrous metals such as copper, brass, bronze, and aluminum. Current densities of 400,000 amp per sq in., sintering times of 1 and 2 cycles of 60 cycle current, and pressures of 5 to 10 tsi are proposed. Cremer suggested using an

Jan 1, 1956

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

Hydrogen forms a beta-stabilized system with titanium, with a beta eutectoid at about 300°C and 44 atomic pct H2. 'The solid solubility of hydrogen in alpha decreases from about 8 to about 0.1 atomic pct from 300°C to room temperature. Hydrogen has little effect on tensile properties, but decreases notch-bar toughness to a large degree. This latter effect appears to be the result of increased notch sensitivity. PRIOR to this investigation, only a small amount of information was available on the effect of hydrogen on the mechanical properties of titanium. The effects of the other interstitially soluble elements, carbon, oxygen, and nitrogen, had received detailed study. Jaffee and Campbell1 indicated that hydrogen up to 1 atomic pct did not affect tensile properties deleteriously. Pitler' indicated that 1 atomic pct H, in titanium reduced the impact strength appreciably, but his alloys contained appreciable amounts of oxygen, and it was difficult to attribute the embrittlement entirely to hydrogen. The high temperature portion of the equilibrium diagram for the Ti-H system was established by McQuillan," and his data generally corresponded with the results of Kirschfeld and Sieverts," Gibb and Kruschwitz," Bevington, Martin, and Mathews," and other investigators. The lower concentration limit of the hydride phase varied considerably among investigators, and Gibb and Kruschwitz9 ad shown that small amounts of contaminants in either titanium or hydrogen caused considerable variation in this lower limit. In view of this pronounced effect of contaminants, the extrapolated value of McQuillan's, about 48 atomic pct at the 325°C eutectoid, appeared the most reasonable. McQuillan's lowest experimental value was 54 atomic pct at a temperature of 450 °C. The density of titanium had been shown to decrease with increasing hydrogen content, but discrepancies were noted among the various investigations. The best values indicated that the density was decreased from 4.56 grams per cc at 0.27 atomic pctl to 3.84 grams per cc at 61.3 atomic pct? This investigation was conducted to determine the effects of hydrogen on a titanium, both in high purity and commercially pure metals, and on high purity a titanium alloys. Material and Fabrication The literature indicated that impurities in either the hydrogen or the titanium must be kept to a minimum. For this reason, the initial studies were made with high purity iodide-refined titanium. The vendor's analysis of the iodide titanium and the hydrogen content of the as-fabricated Y4 in. diameter rods are shown in Table I. Two 1 lb ingots were prepared by arc melting under argon in a water-cooled crucible, using a water,cooled tungsten electrode. This equipment has been described.' As-cast Brine11 hardness numbers of 88 and 58 for these ingots were low enough to insure that the high purity of the metal was maintained during arc melting. The ingots were hot forged to % in. diameter rods at 800°C, cleaned by grit blasting, and then cold swaged to Yz in. diameter rods. The rod was then air annealed at 725 "C, ground to remove scale, and cold swaged to Y4 in. diameter (75 pct reduction in area). The material was then annealed for 1 hr in argon at 800°C to develop an equiaxed a grain size of about 0.05 mm. Micro tensile specimens and microimpact specimens were machined from this rod prior to treatment in the Sieverts-type absorption apparatus. Two lots of commercially pure RC-55 titanium were also used in this investigation to determine the effects of hydrogen and the normal impurities on mechanical properties. The commercially pure RC-55 alloy was obtained in the form of % in. diameter rod. The analysis of this material is also given in Table I. The % in. diameter rods were hot swaged

Jan 1, 1955

By H. Kenworthy, R. B. Fisher, R. G. Knicherbocker, M. M. Fine

The progress made to date in the mineral dressing of complex Arkansas titanium ores is reported in this paper. Concentrates of rutile, a dioxide of titanium, were produced by treating a submarginal ore from the Magnet Cove Rutile Co., Inc., Magnet, Ark. The rutile recovery at present is 45 to 50 pct of the total TiO2, with the possibility of increased recovery with additional research. The work reported herein is part of a general study which will later include results of investigation of other titanium ore bodies in the Magnet, Ark., area. The fragile character of the rutile minerals, the softness of the gangue, the occurrence of pyrite and leucoxene, and the considerable proportion of extremely small size rutile in the presence of montmorillonite- and illite-type clays in the Magnet Cove open-pit mine are the important factors in the mineral dressing of this submarginal rutile ore. History The occurrence of titanium minerals in the Magnet Cove area of Arkansas was recognized as early as 1890, but it was not until about 1912 that any appreciable prospecting for the minerals was undertaken. At that time drilling was begun, a shaft was sunk, and several drifts were driven, but beneficiation to recover the titanium minerals was not attempted. The only successful mining and milling operation of the Magnet Cove rutile deposit was begun in 1932 by the Titanium Corp. of America and continued until 1942. The ore was washed by means of a rotary scrubber and then deslimed in a drag classifier. The discharge was ground in a rod mill, classified, and tabled to recover a rougher rutile concentrate, which was screen-sized and retabled on cleaner tables. The cleaner concentrates were given a reducing roast, screen-sized, and magnetically separated to produce a finished rutile concentrate. Most of the rutile produced during this period was sold abroad. In 1942, the Titanium Alloy Corp. of Arkansas (a subsidiary of the Titanium Alloy Manufacturing Co. of New York) purchased the property and rebuilt the mill. Subsequently, the plant and property were acquired by the Magnet Cove Rutile Co., Inc., of Little Rock, Ark., the present owners. Very little titanium has been produced since 1942. Although the Titanium Corp. activities yielded enough returns to allow continued operation for approximately 10 years, certain factors must be recognized. These are: (1) production of rutile in that period was during a low in the economic cycle which permitted low-cost operation on a small scale, and (2) a considerable portion of the production was above the water level and no drainage problems existed. Prior to this paper there has been no published report of any mineral-dressing investigation of the lower levels of the ore body. Reference is made in another paper1 to an earlier investigation of Magnet Cove rutile by the Rolla laboratory, in which it is stated that recoveries of 12 to 17 pct of the rutile were obtained. The present investigation was undertaken to improve the known milling processes and to provide adequate metallurgical information about the ore treatment. Titanium Technology The titanium mineral of primary interest in the present investigation was the titanium dioxide, rutile. Rutile is one of the industrial minerals whose annual consumption is relatively small but strategically important. The domestic production of rutile was 7100 tons in 1948. The imports of rutile in the same year were approximately 8000 tons.2 A major use of rutile is in the production of welding-rod coatings, for which a product containing a minimum of 92 pct titanic oxide is desired. Other constituents, such as lime, silica, and sulphur, must be held to a minimum, but hard-and-fast specifications for these elements cannot be drawn. It is necessary to incorporate the rutile in a welding-rod coating, make a sufficient number of test welds, and then determine the tensile strength of the weld metal in the as-welded and stress-relieved conditions. Such a test gives

Jan 1, 1950

By G. S. Upadhyaya, A. D. McQuillan

HERE would appear to be a simple relationship between the group number in the periodic table of the early transition metals and the maximum amount of hydrogen which they can absorb.' Thus group IIIA metals (Sc, Y, and La) yield a trihydride in which the metal atoms are on a fcc lattice and the hydrogen atoms occupy both tetrahedral and octahedral interstices. Group IVA metals (Ti, Zr, Hf) form dihy-drides in which the metal atoms are on either a fct or cubic lattice, but in which only the tetrahedral interstices are occupied by hydrogen atoms. In group VA (V, Nb, Ta) the hydrogen-saturated metal attains a composition slightly below that of a monohydride under normal conditions. Finally the metals of group VIA (Cr, Mo, W) do not dissolve appreciable quantities of hydrogen. The manner in which hydrogen solubility disappears on alloying a group VA metal with one from group VIA has previously been investigated.2 It is necessary, in order to obtain a general picture of the reactions of alloys of the early transition metals with hydrogen, to examine a system containing metals from groups IVA and VA in which there must be a change from a fcc to a bee hydride phase. The system chosen for investigation was the pseudobinary system between titanium hydride and niobium hydride. Metallic alloys were prepared by melting iodide-prepared titanium with zone-refined niobium in an argon-atmosphere are-furnace. To ensure homogeneity each alloy was cold-swaged and then heated at 1250°C in a high-vacuum furnace until metallo-graphic examination confirmed its complete homogeneity. Small weighed specimens of the alloys were charged with hydrogen using gaseous hydrogen generated by heating titanium hydride. The apparatus has been described elsewhere.3 Throughout the charging process the hydrogen pressure was kept at about 1 atm while the specimen, initially at 800 °C, was slowly cooled to 150°C over a period of days. The total amount of hydrogen absorbed by each specimen and the room-temperature crystal structure of the hydride powders were determined. The X-ray investigation indicates that the fee hydride phase arises from alloys extending in composition from titanium to 67 at. pct Nb. After a two-phase field lying between 67 and 74 at. pct Nb in which the fee and bee hydrides coexist, all alloys richer in niobium yield a distorted bee hydride. Data derived from parameter measurements are presented in Fig. 1. The atomic volume per metal atom has been plotted against the composition of the initial metallic alloy in order to facilitate comparison of the effects of hydrogen addition in the two phases of different crystal structure. The amount of hydrogen absorbed by each alloy at saturation in terms of the hydrogen to metal ratio and alloy composition is given in Fig. 2. Over the whole range of the fee hydride phase the hydrogen content remains constant, while in the distorted body-centred hydride phase, the hydrogen content increases with increasing titanium content reaching a hydrogen/metal ratio of 1.4 at the boundary of the two-phase region. It seems likely, therefore, that the maximum hydrogen content of the fee hydrides is limited to a hydrogen/metal ratio of 2 because hydrogen atoms

Jan 1, 1962

By T. E. Schmieman, J. E. Miller, M. L. Rizzone

Both centrifugal and reciprocating-type pumps have been widely used in the transport of slurries. Although with some limitations, centrifugal pumps may be used, especially for short-haul systems, however, for the long pipelines the reciprocating pumps are better suited. A state-of-the-art review is presented in which a discussion of applications is made and some of the problems associated with meeting the proper design conditions for satisfactory service are discussed. Several developments underway give considerable promise of better pumps in the future, although the current level of development provides for an economical means to move slurries. The movement of liquids in pipelines necessarily occasions the use of pumps. The petroleum industry is familiar with the transport of solids through mud pumps and cementing and fracturing pumps where the movement of slurries is an everyday matter. In the drilling of an oil well, the circulating fluid utilized to remove drill cuttings is called drilling mud. This substance is usually a fairly sophisticated material designed to develop certain characteristics desirable in the drilling process. The cuttings are suspended in a moving column of this fluid and brought to the surface. The separation of the cuttings from the drilling fluids is accomplished by the use of shaker screens and settling pits; however, it is impractical to remove the cuttings completely and as a result they are pumped through the mud pumps back into the circulating stream. Over the years, mud pumps have been improved so that rather long life can be obtained from liquid end parts subject to the attritional effects of the abrasive-laden fluid. It is from this background that reciprocating-type slurry pumps have been developed. Centrifugal Pumps Centrifugal pumps have also been used to transport solids, where low heads are required, typically up to 200 ft or so, and for short hauls. The centrifugal pump is a hydrokinetic device wherein the increase in velocity of a fluid stream is converted to head, and to achieve high heads a large change in velocity is necessary. Abrasive laden fluids cause wear on impellers and casings as a result of erosion by the fluid and the suspended particles. Centrifugal pumps, therefore, can only be used where the internal velocity of flow is rela- tively low. The advantage of centrifugal pumps is their high capacity at relatively low capital cost and usually relatively small space requirement. One of the disadvantages of the centrifugal pump when used in slurry pipelining can be seen in its typical pressure-volume performance relationship, which tends to work against the application (see Fig. I). If an increase in pressure (head) is occasioned by flow restrictions in the pipeline, say by the dropping out of solids, a desirable characteristic of a slurry pump would be that it develop increased pressure to overcome the restriction. The centrifugal pump provides the increased pressure only at the expense of considerably reduced volume which then results in a lower flow velocity. With the reduced flow rate, adequate velocity to hold the material in suspension and keep it flowing in the line might not be achieved. If centrifugal pumps are considerd for the movement of solids in a long line, a series of pumps must be staged in order to provide the necessary motivating force. A large number of pumps in the line would be required, since each of the pumps could provide only a small pressure increment. An equal number of standby pumps

Jan 1, 1971

By H. Kazemi

An ideal theoretical model of a naturally fractured reservoir with a uniform fracture distribution, motivated by an earlier model by Warren and Root, has been developed. This model consists of a finite circular reservoir with a centrally located well and two distinct porous regions, referred to as matrix and fracture, respectively. The matrix has high storage, but low flow capacity; the fracture has low storage, but high flow capacity. The flow in the entire reservoir is unsteady state. The results of this study are compared with the results of the earlier models, and it has been concluded that major conclusions of Warren and Root are quite substantial. Furthermore, an attempt has been made to study critically other analytical methods reported in the literature. In general, it may be concluded that the analysis of a naturally fractured reservoir from pressure transient data relies considerably on the degree and the type of heterogeneity of the system; the testing procedure and test facilities are sometimes as important. Nevertheless, under favorable conditions, one should be able to calculate in-situ characteristics of the matrix-fracture system, such as pore-volume ratio, over-all capacity of the formation, total storage capacity of the porous matrix, and some measure of matrix permeability. INTRODUCTION The analysis of flow and buildup tests for obtaining in-situ characteristics of oil and gas reservoirs has received considerable attention in the past decade. Most of the available techniques result in reliable conclusions in macroscopically homogeneous reservoirs or in the homogeneous reservoirs with only certain types of induced and/or inherent heterogeneity (such as wellbore damage, etc.). In general, the greater the degree of heterogeneity, the less the reliability of the information deduced from the pressure transient data. A commonly encountered heterogeneous system is a naturally fractured reservoir where two types of distinct porosities occur in the same formation. The region containing finer pores may have high storage and low flow capacities. This is called the matrix. The remaining region may have high flow capacity with low storage. The latter region is generally the set of interconnecting fractures and fissures of the rock, and for this reason it is called the fracture. Ordinarily, we wish to obtain the permeability and porosity of each region and perhaps the frequency of the fracture distribution in a reservoir. Such information is necessary for reservoir engineering. Other information, such as wellbore damage, will be useful in evaluating possible remedial work for such fields. Few authors have suggested theories to aid in calculating the in-situ characteristics of a naturally fractured reservoir similar to what we have described above. Pollardl suggested that a naturally fractured reservoir contained three distinct regions: a damaged or an improved region surrounding the wellbore, and the two remaining regions the same as described earlier. He suggested that the flow was taking place from the tight matrix into the highly conductive fractures, then into the we wllbore region and finally into the well column. He concluded that the average pressure buildup in each of these distinct regions can be expressed approximately in terms of an exponential decay function of time. He also hypothesized that the decay coefficients for each of these functions were significantly different from each other; consequently, each of these functions became dominant in turn, in the process of pressure buildup. Thus, by a proper graphic plot of the logarithm of wellbore pressure differences vs buildup time, each of these functions could be determined (see Fig. 1). Pollard suggested methods of determining the wellbore damage and fracture volume. Later Pirson and Pirson2 extended

Jan 1, 1970

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year's symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. 'It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved') and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

By James Terry Duce

The symposium on production for the year 1941 contains few papers on the foreign situation. Rigid censorship prevails in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even truer than in the last war, owing to greater mechanization of armies. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to AutHORs In order to facilitate interpretation of the data in this chapter, we print the fol-lowing excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir.. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1942

By James Terry Duce

The symposium on production for the year 1941 contains few papers on the foreign situation. Rigid censorship prevails in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even truer than in the last war, owing to greater mechanization of armies. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to AutHORs In order to facilitate interpretation of the data in this chapter, we print the fol-lowing excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir.. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1942