Search Documents

By Arthur L. Christenson, Clarence E. Jackson

In the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition* may be corrected to the grain size observed in an actual weld? or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.8 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2Ioo°F. has been used. In studies of the end-quench hardenability specimen quenched from 2Ioo°F. instead of from a lower temperature of I7OO°F., it is impor-TaiiT to ascertain The relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6'7 French has considered this effect from both theoretical and experimental aspects. In French's studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been propped: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1944

By E. H. Rose

The present symposium on flotation machines provides a unique opportunity for group reappraisal of standard or habitual viewpoints. A symposium is by definition a trading post- for observations that might prove complementary when put together, thus leading to useful thoughts that might not have been evident from the original observations individually. The present paper, pertaining to power consumption in flotation, is deliberately an experiment of that kind. Data were solicited from the operating superintendents of several of the major flotation plants on this continent. The information received, covering a total of 14 separate operations in seven plants, has been collated in terms of power intensity; that is, the total power input per cubic foot of cell volume. This departs somewhat from the conventional expression of power per ton of ore treated, though the latter figure is also given for the plants concerned. Because of wartime restrictions, particularly in Canada, identifying names of plants and machines are withheld. Not as a firm conclusion, but as a tender for symposium discussion, the following points are made: 1. That flotation is a power operation in much the same sense as ball milling. 2. That contact time is the complement of power intensity and may be decreased as the latter is increased. 3. That a decrease in flotation power per ton of ore can result from an increase in power intensity. Analogy with Grinding In grinding, it has become axiomatic that the more the power put into a given operation, the greater the work performance. The analogous view is now proposed that the effectiveness of any flotation operation will be related to the mechanical energy usefully applied to that operation. Under this view, each increment of properly directed input energy should give either an increase in unit tonnage or an improvement in the metallurgical separation (concentrate grade or tailing grade), until either the theoretical limit imposed by mineral constitution or surface condition is reached, or until further increments of power become uneconomic under the law of diminishing returns. Thus, as in grinding, there are two forms of output that greater power input or improved utilization of power can produce. As for the law of diminishing returns, lower unit cost of power through improved generating efficiency in the past decade has pushed the limit back. Over and above this, however, there is strong indication in the operationg data herein presented that higher power intensity results in an actual economy of over-all power consumption. Like crushing and grinding, flotation accomplishes a rupture of the forces of molecular attraction, by taking particles from the common environment and placing them in the two separate environments of

Jan 1, 1947

Discussion of the paper of W. R. Shimer and F. O. Kichline, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 81, September, 1913, pp. 2361 to 2377. ALLERTON S. CUSHMAN,* Washington, D. C.:-I have been much interested in Mr. Shimer's valuable contribution. The apparent fact that the oxides of certain metals which are not reduced by hydrogen per se, are reducible when the oxides are dissolved in iron in small quantity, is brought out for the first time, and is worthy of the careful attention of investigators. The Ledebur method has been subjected to considerable criticism, owing to the alleged fact that it did not measure the oxygen combined with impurities. Personally I have found the method extremely helpful in spite of the minute quantities of oxygen with which it deals. Mr. Shinier points out that the highest oxygen he obtained by over-blowing was 0.074 per cent., while the minimum quantity in a properly finished steel was in the neighborhood of 0.02 per cent. The Ledebur method is used as a constant check on the quality of heats made in practice under my direction. In dealing with a very pure commercial iron, we should expect to find and would find difficulty in galvanizing sheets made from a heat running 0.07 per cent. oxygen. In fact, we do not like to have the oxygen rise above 0.03 per cent. I am inclined to agree with the author that excessive oxygen leaves a bath of metal in a very short time, but nevertheless I believe it takes only a very little combined oxygen to begin to make its presence felt in the pickling and galvanizing department, when sheet metal is the product manufactured. As Mr. Shimer points out, the higher the carbon, the lower the oxygen danger, and it is partly for this reason that the manufacture of carbon-free metal in the open-hearth furnace has to be so very carefully watched and controlled from the furnace through to the finished product. It is quite possible that, there is a critical temperature of dissociation between iron and oxygen, although the critical points may vary in baths of different carbon content. Unfortunately, the accurate determination of the temperature of a molten bath at the time of pouring or teeming is a very difficult matter. For a long time I have been wishing that there were some reliable data which would indicate the effect of the tem-

Jan 12, 1913

By H. V. Winchell

It seems to me that uniformity of mining law in North America must of necessity start with uniformity in each country. I understand that the Provinces of Canada have the right to make their own individual laws and conditions, to prescribe the terms under which the prospector or the applicant for mineral titles may secure the same. That is not true of the states in the United States. In this country, the Federal Mining Law was made applicable to the public domain, which, at the time of the adoption of this Act in 1872, was chiefly west of the Missouri River; it is impossible to locate a mining claim in most of our eastern states. It is true, however, that there are certain holdover rights, mostly obsolete, arising from the fact that at the time of the formation of the Confederation of States, the land that belonged to each state became the property of the Federal Government. I am not quite correc-t in that, it was sometime after the adoption of our Constitution, I think it was 1778, but those rights were largely, by agreement, surrendered to the Federal Government; but it is a fact that the great acquisitions of territory in the West, with the single exception of Texas, were of domain that came into the possession of the Federal Government and our Federal Mining Law applies to that territory. No state has the right to (by legislative enactment) enlarge upon the rights given by the Federal Mining Law, governing the acquisition of mining claims in its territory, within its boundaries. Each state, however, may, and some of them do, limit somewhat the rights given to the prospector. For instance, the Federal Mining Law provides that a claim may be taken, staked upon the public domain, of 600 ft. in width and 1500 ft. in length. Some of the states, like South Dakota and Colorado, have at times said "that is an excessive amount of land for a single mining claim; we will therefore limit it to 300 ft. or 200 ft. in width." There is, therefore, not any direct and immediate need for uniformity of mining laws in the United States, such as there might possibly be if it were considered at all desirable upon the whole in Canada. The initiation of mining rights under the Federal Mining Act is the act of discovery of valuable mineral in place, referring now to the lode mining claims, but the same is true of the placer claim. It is true that the emphasis has never been laid upon the word valuable and that

Jan 1, 1920

By C. E. Nelson

THE purpose of this discussion is to outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as far as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, the principal aim of this paper will be to deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. TYPES OF MELTING PRACTICE All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux.* The flux provides protection during melting and a molten pool of flux into which the solid magnesium melts. It is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies; then on quiet standing separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is usually desirable. The open-pot method is used generally in the following processes: (I) alloying and secondary smelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings requiring hand ladling, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protec-

Jan 1, 1944

By E. H. Rose

The present symposium on flotation machines provides a unique opportunity for group reappraisal of standard or habitual viewpoints. A symposium is by definition a trading post- for observations that might prove complementary when put together, thus leading to useful thoughts that might not have been evident from the original observations individually. The present paper, pertaining to power consumption in flotation, is deliberately an experiment of that kind. Data were solicited from the operating superintendents of several of the major flotation plants on this continent. The information received, covering a total of 14 separate operations in seven plants, has been collated in terms of power intensity; that is, the total power input per cubic foot of cell volume. This departs somewhat from the conventional expression of power per ton of ore treated, though the latter figure is also given for the plants concerned. Because of wartime restrictions, particularly in Canada, identifying names of plants and machines are withheld. Not as a firm conclusion, but as a tender for symposium discussion, the following points are made: 1. That flotation is a power operation in much the same sense as ball milling. 2. That contact time is the complement of power intensity and may be decreased as the latter is increased. 3. That a decrease in flotation power per ton of ore can result from an increase in power intensity. Analogy with Grinding In grinding, it has become axiomatic that the more the power put into a given operation, the greater the work performance. The analogous view is now proposed that the effectiveness of any flotation operation will be related to the mechanical energy usefully applied to that operation. Under this view, each increment of properly directed input energy should give either an increase in unit tonnage or an improvement in the metallurgical separation (concentrate grade or tailing grade), until either the theoretical limit imposed by mineral constitution or surface condition is reached, or until further increments of power become uneconomic under the law of diminishing returns. Thus, as in grinding, there are two forms of output that greater power input or improved utilization of power can produce. As for the law of diminishing returns, lower unit cost of power through improved generating efficiency in the past decade has pushed the limit back. Over and above this, however, there is strong indication in the operationg data herein presented that higher power intensity results in an actual economy of over-all power consumption. Like crushing and grinding, flotation accomplishes a rupture of the forces of molecular attraction, by taking particles from the common environment and placing them in the two separate environments of

Jan 1, 1947

By Arthur L. Christenson, Clarence E. Jackson

In the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition* may be corrected to the grain size observed in an actual weld? or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.8 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2Ioo°F. has been used. In studies of the end-quench hardenability specimen quenched from 2Ioo°F. instead of from a lower temperature of I7OO°F., it is impor-TaiiT to ascertain The relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6'7 French has considered this effect from both theoretical and experimental aspects. In French's studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been propped: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1944

By F. M. Perkins, R. H. Jamison

Publications concerning scaling laws for laboratory flow models of oil reservoirs indicate that the relative permeability and capillary pressure relations must be the same functions of saturation in the model and its prototype. In this paper, the relative permeabilities and saturations are redefined in a way which permits one to have diflerent relative permeability and capillary pressure relations in the model and prototype. The development of the new scaling criteria is demonstrated by deriving scaling laws for one simple flow problem. INTRODUCTION The successful application of information gathered through bench-scale model studies to the prediction of multi-phase fluid flow behavior in petroleum reservoirs requires careful consideration of the scaling criteria. The requirements which must be met for a small-scale model to duplicate the behavior of a much larger reservoir prototype have been discussed by Leverett, et al,' Rapoport,2 and Geertsma, et al.3 According to these authors, the relative permeabilities to water, oil and gas and the dimensionless capillary pressures must be the must have the same values in the model and prototype. Furthermore, they point out that the viscosity ratios must have the same values in the model and prototype. In addition to these requirements, other scaling criteria are given which, when considered, usually dictate a much higher permeability in the model than exists in the reservoir. Since the more permeable model sands may have connate-water and residual oil saturations quite different from those in the prototype, the scaling requirements pertaining to the dependence of relative permeabilities and dimension l ess capillary pressures on saturation usually are not met. Also, if the model fluids are selected to give equal viscosity ratios in the model and prototype, one may find greatly different mobility ratios* in the two cases and, therefore, may expect grossly different flow patterns. For this reason, Craig, et al,' correlated the results of their model studies with mo- bility ratio rather than with viscosity ratio. As yet, however, no satisfactory method has been advanced which permits use of anything other than the scaling requirements outlined in the previously mentioned papers. The purpose of this paper is to present a method of developing a set of scaling criteria which permits different relationships between saturation and relative permeability or capillary pressure in the model and prototype. Rather than attempt to report scaling criteria for a variety of practical situations, this paper demonstrates by use of one simple example how the modified scaling criteria are derived.

By H. L. Riley, B. W. Gandrud

A froth flotation unit was added to the DeBardeleben Coal Corporation's Empire washer at Empire, Alabama, in the fall Of I94O following an investigation of possible ways and means of recovering coal values from settling-tank overflow or slurry. Officials of the DeBardeleben corporation hoped that some practical and reasonably economical way could be found for recovering fine coal from overflow water, although there had as yet been very little progress along this line in the Alabama coal fields. The Bureau of Mines was asked to cooperate in the project through its Southern Experiment Station, at University, Alabama. This paper presents a brief description of the process and the installation that resulted from the investigation of the overflow water or slurry problem at the Empire mine. The experimental data include' as a Part of this Paper were obtained during the course of the investigation in 1940 Since that time, however, the flotation unit has been running more or less continuously without significant operational changes and is still Performing pretty much in accordance with the data obtained in 1940. Flowsheet at Empire and Type of Coal Treated The Empire mine is developed on the Black Creek bed near the the border of the Warrior field. The coal in this bed is extremely low-ash and although there is an almost complete absence of bone coal and partings, the bed is so thin that, with mechanized mining, a high percentage of rock from roof and floor inevitably gets into the run-of-mine coal. The thickness of the Black Creek bed throughout the part of the Warrior field in which it is mined extensively is rarely over 30 in. and probably would average about 25 in, the coal is of the high-volatile A rank and of excellent quality, but as a result of admixture of roof and floor material, the run-of-mine product usually contains I ; to 20 pct rock by weight. he following is a proximate analysis on an "as-received " basis of a typical seam sample from the Empire mine:' moisture, 3.0 pet; volatile, 34.6 fixed carbon 58.3; ash, 4.1 This sample shelved 15,070 Btu per pound and 0.9 pct sulphur on a moisture-and-ash-free basis. In the Empire preparation plant the lump sizes above 3 in. are removed and hand-picked on a Marcus conveying Screen, the 3 to ? -in. size is removed by vibrating screens and washed in two Montgomery single-cell jigs, and the ?-in. to o slack is cleaned on four diagonal

Jan 1, 1949

By John L. Lamont, Walter Crafts

SELECTION of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of hardenability,1 as-quenched hardness,2,3 and tempered tensile strength.4 Ductility and toughness may also be estimated if the steel is completely hardened on quenching,5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In fine-grained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accompanied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to 4 in. in diameter. PROCEDURE The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1o30, 1040, 1340, 3310, 3316, 4320, 4330, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 9310, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.35. The bars were tempered as follows: ½ in., I in., and I 5/8 in., 2 hr; 2 ½ in., 3 hr; 4 in., 5 hr. All bars were air-cooled from the tempering tem-

Jan 1, 1947

By A. M. Gavdin, F. W. Bowdish

Mineral dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,? its magnetic remanence,³ the turbidity of its suspension," and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid—both internal and external—the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample.2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. Apparatus In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. I and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1947

By A. M. Gavdin, F. W. Bowdish

Mineral dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,? its magnetic remanence,³ the turbidity of its suspension," and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid—both internal and external—the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample.2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. Apparatus In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. I and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1947

By G. L. Boxer, C. B. Smith, W. J. Atkinson

Since the inception of the Ashton (formerly Kalumburu) Joint Venture in 1972 the parties have expended $24 million in exploration for diamonds in the Kimberley region. This has resulted in the discovery of the currently subeconomic Ellendale deposits in 1976/77 and the economic Argyle - Smoke Creek Deposits in 1979/80. In addition to Argyle and Ellendale, some 90 kimberlitic and lamproitic bodies have been discovered grouped broadly into three provinces, on the west, east and north margins of the Kimberley block. These bodies range in size from dyke-like features less than 1 m (3 ft) in width to pipes with a surface area of 128 ha (316 acres). The bodies with larger surface area are volcanic crater deposits, infilled with air-fall and water deposited tuffs and epiclastic sediments. Diamond content ranges from trace to economic concentrations. The exploration discoveries were facilitated by early recognition that the petrography, mineralogy and chemistry of the diatremes varied from the classical kimberlites of Kimberley, South Africa, to unusual more highly fractionated, alkaline, silicic varieties having affinities with leucite-lamproite. Indirect methods of exploration were used, primary reconnaissance work being stream gravel sampling for kimberlitic indicator minerals. Evaluation showed Ellendale diamonds are 90% gem and near gem, but the low grades and tonnage render the deposits unpayable at today's diamond prices. After discovery in late 1979 and completion of a feasibility study by the end of 1982, evaluation studies proved Argyle to be economic. Alluvial diamond mining commenced in 1983 producing 6.2 million carats (Mct) that year, 60% being of industrial quality. Open-pit mining of the AK1 lamproite should start in 198511986 at a rate of 3 million t/a (33 million stpy) and produce 25 Mct/a, making this mine, and Australia, the world's largest producer of diamonds by weight. The revenue from diamond deposits is a function of the grade and the value of the diamonds. The grade is the product of the frequency of occurrence of the diamonds (stone density) and the mean stone size; the value of the stones is strongly related to their size distribution. During evaluation of the West Australian deposits, the diamond distribution was found to vary markedly in stone density and stone size. These variations corresponded with changes in the rock type hosting the mineralization. As a consequence, geological mapping of individual lamproites within the multiple vents and careful monitoring of the diamond distribution became an important part of the evaluation work. Similar variations in stone size and frequency were found to accord with separate alluvial terraces and fan gravels derived by erosion from the Argyle AK1 lamproite.

Jan 1, 1985

By John G. Koert, Koert D. Burnham, John G. Broughton

Wollastonite in Essex County, New York, occurs as a typical contact mineral in a series of rocks metamorphosed by anorthosite. Sole current use is in various types of electric welding fluxes. Its uniform lathlike shape suggests its use as a specialized filler. Introduction Wollastonite (CaSiO3) was first noted in the vicinity of Willsboro, Essex County, New York, about 1810 by Dr. William Meade, and described from the same locality in 1821 by Lardner Vanuxem.' Recent exploration and development indicate that the deposit is of adequate size for continued exploitation on a larger scale than the present operations. The only other known occurrence of like magnitude in this country is in Kern County, California.* Wollastonite has been reported from Michigan, Pennsylvania, and Lewis County, New York, but these are little more than mineral localities. Geology The Essex County wollastonite has been found outcropping at numerous separate localities in a belt of contact metamorphosed sediments, 1/4 mile wide, which begins 2 miles southwest of the village of Willsboro and trends N. 70" W. for approximately 6 miles (Fig. I). In this belt, the pre-Cambrian Grenville has been injected and partially replaced by the more liquid portions of an anorthositic magma. Bud-dington and Whitcomb3 have described the rock in this contact metamorphosed belt as "Mixed gneisses: Grenville mafic, pyroxenic and garnetiferous gneisses and skarns* with local nearly uniform garnet or pyroxene layers and with gabbroic anorthosite sheets. A few limestone layers." These rocks are underlain, presumably at no great depth, by gabbroic anorthosite gneiss, the typical Whiteface border facies of the Adirondack anorthosite massif. The occurrence of wollastonite in large quantities was discovered during the quarrying of the garnet-rich layer that overlies the wollastonite at one opening. Further prospecting revealed its presence elsewhere in the belt, overlain in most places by the garnet. Accurate tracing of the wollastonite is difficult, owing to the glacial cover and to the fact that the weathered surface of the mineral has a dark, dirty brown color, and that the wollastonite itself has been dissolved more or less completely along the outcrops. It has, however, been noted at 10 localities within the skarn belt in the first 2 1/2 miles from its southeastern end. It has not been found in the northern half of the belt and therefore may be limited to the southern half. At the Fox Hill quarry, which is the main opening, 150 ft. have been exposed, showing an aggregate thickness of 30 to 35 it. Of

Jan 1, 1948

By Koert D. Burnham, John G. Broughton, John G. Koert

Wollastonite in Essex County, New York, occurs as a typical contact mineral in a series of rocks metamorphosed by anorthosite. Sole current use is in various types of electric welding fluxes. Its uniform lathlike shape suggests its use as a specialized filler. Introduction Wollastonite (CaSiO3) was first noted in the vicinity of Willsboro, Essex County, New York, about 1810 by Dr. William Meade, and described from the same locality in 1821 by Lardner Vanuxem.' Recent exploration and development indicate that the deposit is of adequate size for continued exploitation on a larger scale than the present operations. The only other known occurrence of like magnitude in this country is in Kern County, California.* Wollastonite has been reported from Michigan, Pennsylvania, and Lewis County, New York, but these are little more than mineral localities. Geology The Essex County wollastonite has been found outcropping at numerous separate localities in a belt of contact metamorphosed sediments, 1/4 mile wide, which begins 2 miles southwest of the village of Willsboro and trends N. 70" W. for approximately 6 miles (Fig. I). In this belt, the pre-Cambrian Grenville has been injected and partially replaced by the more liquid portions of an anorthositic magma. Bud-dington and Whitcomb3 have described the rock in this contact metamorphosed belt as "Mixed gneisses: Grenville mafic, pyroxenic and garnetiferous gneisses and skarns* with local nearly uniform garnet or pyroxene layers and with gabbroic anorthosite sheets. A few limestone layers." These rocks are underlain, presumably at no great depth, by gabbroic anorthosite gneiss, the typical Whiteface border facies of the Adirondack anorthosite massif. The occurrence of wollastonite in large quantities was discovered during the quarrying of the garnet-rich layer that overlies the wollastonite at one opening. Further prospecting revealed its presence elsewhere in the belt, overlain in most places by the garnet. Accurate tracing of the wollastonite is difficult, owing to the glacial cover and to the fact that the weathered surface of the mineral has a dark, dirty brown color, and that the wollastonite itself has been dissolved more or less completely along the outcrops. It has, however, been noted at 10 localities within the skarn belt in the first 2 1/2 miles from its southeastern end. It has not been found in the northern half of the belt and therefore may be limited to the southern half. At the Fox Hill quarry, which is the main opening, 150 ft. have been exposed, showing an aggregate thickness of 30 to 35 it. Of

Jan 1, 1948

By W. Crafts, J. L. Lamont

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By J. L. Lamont, W. Crafts

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By George Krauss, Seth R. Thomas

One complete cycle, allstenite to martensite to aus-tenite, of Martensitic transformation was induced in a commercial 18 Cr-8 Ni stainless steel. Transmission electron microscopy showed that the reverse transfarmation, martensite to austenite, perpetuated the dense defect substructure of the martensite produced by the direct transformation, austenite to 'martensite, and reproduced the retained austenite matrix orientation. A general precipitation of lathlike M,,C, particles was noted to be present in, and is suggested as cause for, regions of martensite that Izad formed after a complete cycle of transformation. The habit plane of the precipitate particles was found to be within 5 a plane previously established as the habit of nitride precipitates of similar morphology in bcc iron. The direct transformation of austenite (y) to martensite (a) in metastable 300 series stainless steels has received considerable attention in the past,'-8 and the martensite product given special emphasis in recent years,9"*u but little information has been published about the reverse martensitic transformation during which bcc a martensite is converted to fcc y austenite."-" The reversal mechanism and the resulting crystallographic relationship between parent and product austenite are of fundamental concern. The reversal product, fully austenitic, and hereafter referred to as reversed austenite, exhibits a defect structure far different from its virgin counterpart. Some studies have been reported in which the structure of reversed austenite in iron nickel alloys is compared to annealed austenite with respect to austenite strengtheningM and Stabilization.' The martensite in these Fe-Ni alloys, however, shows a basic difference from that produced in stainless steels. Structurally, the Fe-Ni martensite is profusely twinned," while the (low-carbon) Fe-Cr-Ni martensite contains a high density of tangled dislocations and is apparently twin-free.I0 reediis" has recently shown in an Fe-16 Cr-12 Ni stainless alloy that this typical martensitic defect structure and the reverse transformation directly influence the structure of the reversal product. He found that much of the reversed austenite had returned to the orientation of the virgin austenite and that fine twins were formed in the austenite after the reverse transformation. This investigation was undertaken in order to describe as completely as possible the structural changes produced by a cycle of transformation in a typical 18-8 stainless steel. EXPERIMENTAL PROCEDURE The 301 stainless steel under investigation (17.44 Cr, 7.75 Ni, 0.80 Mn, 0.60 Si, 0.40 Mo, 0.40 Cu, 0.08 C, 0.03 N, bal Fe)was received as 0.060-in.-thick

Jan 1, 1968

By Joshua I. Tracey, Mackenzie Gordon

THE bauxite deposits in central Arkansas were formed by weather¬ing, in early Eocene time, of fresh or kaolinized nepheline syenite above the water table in a subtropical climate of fairly continuous moisture. Four types are recognized: (1) residual bauxite deposits on kaolinized nepheline syenite, (2) residual deposits on kaolin and bauxite detritus, (3) alluvial deposits of sorted pebbles and pisolites of early Wilcox age, and (4) rubble deposits of later Wilcox age. All were invaded by kaolin and siderite during subsequent burial by Eocene sediments. PART I-FIELD RELATIONS OF THE DEPOSITS The Arkansas bauxite region for years has produced about 95 pct of the domestic supply of bauxite of the United States and it contains today reserves of more than 40 million tons-nine tenths of the known domestic reserves. During World War II, the Arkansas bauxite deposits were explored jointly by the U. S. Geological Survey and the U. S. Bureau of Mines. Some 6000 holes were drilled by rotary rigs under contract to the Federal Govern¬ment, which resulted in the discovery and delimiting of approximately 20 million tons of ore in place. Detailed study of the many sections cored through the bauxite, of data from a much greater number of drill holes made available by all the operating companies, and of the extensive mine faces exposed in the strip pits, has yielded valuable geologic information about the origin of the deposits. It is now possible to piece together a paleotopographic picture of the deposits and the now-buried land surface on which they formed. The bauxite region in the center of Arkansas (Fig 1) contains two producing districts: one in Pulaski County, just south of Little Rock, and the other in Saline County, about 15 miles to the southwest. The deposits in both districts are associated with hills of nepheline syenite, bosses of a large batho¬lith that was intruded into Paleozoic rocks and later buried beneath coastal plain sediments deposited during Cenozoic time. The folded Paleozoic rocks are exposed in the northwest half of the state and are covered in the southeast half by the nearly flat-lying coastal plain sediments. The older rocks were intruded by nepheline syenite, probably in Late Cretaceous time, and sub¬sequently were eroded so as to expose the top of the batholith. In Paleocene time, marine limestone and laminated black silty clay of the Midway group were deposited in an advancing sea, and covered all but the most elevated parts of the batholith. Erosion of the islands of nepheline

Jan 1, 1952

By Frederic E. Carter

THERE have been many attempts to prove that platinum was known to the ancients, but since no traces of the metal have been found in the relics of early times, it must be concluded that it was not known to them. As far as records go, it was actually first discovered in the 16th century in a Spanish mine on the Pinto River in South America; from which source it received its name of Platina del Pinto (little silver from the Pinto). It was more or less of a rarity and was a subject of interest to a few chemists only, until the year 1822 when the metal was first discovered in Russia. In 1819 there were noticed in the washings of the gold sands of the southern part of the Ural Mountains, grains of a heavy white substance, but it was not until three years later that this substance was found to contain platinum. While at first the amounts of platinum brought from the Urals were meager, prospecting soon disclosed rich deposits extending over a considerable area, and nuggets from 10 to 20 lb. were by no means rare. This discovery assured to chemists an ample supply of platinum for their crucibles, etc. The ore is now found in various parts of the world but the richest deposits are still found in the Ural Mountains. The platinum of commerce is obtained entirely from alluvial deposits at depths varying from 6 to 40 ft. The sand and gravel of former river beds are subjected to a series of screenings and washings to effect the separation of the ore. Actually, probably all gold-bearing gravel beds of the world contain platinum, and it is more than likely that large quantities of platinum ore have been thrown away with the black sand washings from gold placer deposits. This is especially true of the alluvial deposits of the Pacific Coast in California and Oregon. Platinum ore is usually found in the form of rounded or flattened grains of "sand," and occasionally in irregular lumps of the size of peas. Large nuggets are very rare. The ore has a metallic luster and is distinguished by its steel gray color, but shows light gray streak when rubbed on a hard white surface; it has a high specific gravity, 16 to 19; is infusible in the hottest blast furnaces, and insoluble in any single acid. Platinum ore is a complex body consisting of the metal in combination with varying proportions of the other members of the platinum group; iridium,

Jan 1, 1928