Search Documents

By Joseph Daniels

The Fritz Engineering Laboratory was built under the direction of John Fritz, and presented by him to the University. A view of the building, looking east, is shown in Fig. 1. The building was started in 1909, and completed in 1910, although all of the equipment was not placed until later. Mr. Fritz gave his personal attention to the details of construction and equipment, and it was his custom to drive over every day to the University from his home in Bethlehem and spend some hours watching the work, offering suggestions, making changes, and planning new work. The result is a building and an equipment which embody his practical ideas. The laboratory structure is of the steel mill-building type, of light-colored brick, 91 by 114 ft., of which a section is shown in Fig. 2 and the floor-plan in Fig. 3. The steel frame carries the roof and traveling crane-way. Ample light has been provided by numerous windows in the side and end walls, in the clerestory, and by a skylight 84 ft. long and 9 ft. wide in the north roof. The main aisle of the building is 49 ft. 2 in. between centers of crane-columns, and has a clear height of 40 ft. The remainder of the width is taken up by two side aisles, 18 ft. high. The laboratory consists of four sections: (1) A general testing-section containing the testing-machinery, a small machine shop, and an office; (2) a cement-testing room; (3) a room for making and storing concrete test-specimens; (4) a hydraulic section.

Jan 1, 1912

By Chas. Y. Clayton, Francis B. Foley, W. E. Remmers

DuRing the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr. Howe's laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe's death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.' Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 1, 1926

By A. W. H. Morris, E. A. Steigerwald

The jatzgue beizazriov oj Mietal matrix co))zpos~tes in tension -lensiom loading has been imestigated as a junction of Dolume fraclion veinfovcelnent using the model systems of a silver matrix reinforced with contlnuous or dzscontztinuous aligned tungsten jilamenls and continuous aligned steel filamenls. Appreciable impvocetnents in fatigue strength were obseved in all syslems inzvesLigated, the degree of sl renglhenng-increasing with increasing volume fraclion of reinforcement. The mode of fatigue failure was found to be a function of colutrre jp-actiotz and was also noted to be controlled by the relative fatigue and strength characlerislics of the matrix and reinforcemenl. THE advantages to be gained by suitably incorporating high-strength filaments or whiskers into metallic matrices are well-recognized.' To date emphasis has been placed on the experimental determination of tensile strengths and elastic moduli of metal matrix composites measured parallel to unidirectionally aligned filaments. Several attempts have been made to relate experimentally measured tensile properties to theoretical values calculated from the properties of the components on the basis of the relatively simple "rule of mixtures" analysis. However, relatively few data have been reported in the literature on the fatigue behavior and mechanism of fatigue failure of metal matrix composites. In a study of fatigue crack propagation in aluminum plus steel wires and aluminum plus tungsten wires, Forsyth et a1.2 found that the incorporation of small numbers of filaments suitably dispersed were capable of substantially reducing the rate of fatigue crack propagation. For this purpose, the strength of the filaments appeared to be more important than the aspect ratio and the authors reported that parallel filaments were not the most favorable orientation for increased strength. In a basic study of the fiber reinforcement of metals, Williams and 0'brien3 report preliminary results which indicate a considerable improvement in fatigue strength in reversed bending fatigue of a steel wire-reinforced aluminum alloy composite. In a study of the influence of interfacial bonding on fatigue behavior, Baker4 has also reported improved fatigue properties in stainless steel-reinforced aluminum composites. In contrast, Ham and place5 report that, although tensile properties are improved greatly by filament reinforcement, the reinforcement of copper with continuous, brittle tungsten wires up to 23 vol pct was comparatively ineffective against fatigue. The authors attribute the poor fatigue properties of the composite to fatigue hardening of the matrix at the tips of cracks which can build up stress concentrations sufficiently large to fracture proximate filaments. Baker and cratchley6 failed to find marked improvements in the reversed-bending fatigue properties of silica-reinforced aluminum. The study was complicated by the complex behavior in a composite during the compres-sive half-cycles imposed in this type of loading. This was manifested in the failure of the composites by de-lamination, a contributing factor being the presence of aluminum oxide at the matrix-filament interface. Prior to the general acceptance of filament-rein-

Jan 1, 1968

By Jerome F. Kuzmick

Many investigations have been made on the effect of the variables of pressure, sintering temperature and sintering time on the physical and microstructural charactcristics of metal-powder compacts. Severa1 such investigations have indicatcd that pressure is the least important of these three factors in an attempt to secure a dense. strong compact by a simple coltl-pressing and sintering procedure. However, it was felt that a further study of the effect of pressure on pressed and sintered metal powder compacts might prove interesting, for the following reasons: In work done in the past on the effect of pressure, temperature. arid time, the, metal-powder compacts were subjected to long sintering periods, and temperatures right up to the melting point of the metal were applied. It was thought that pressure might exert a more profound effect under short-time simtering and within narrower ranges of temperature. such as normally would be applied in large-scale production of metal-powder parts. 2. It was hoped that something further might be learned of the nature of the bond in pressed and sintered metal-powder compacts. 3. It was thought that interesting infor mation concerning the work-hardening effect of pressure on the crystal structure. of sintered metal-powder compacts would be obtained. Procedure Rectangular bars, 2 by 1/2 by 1/4 in. were molded from the following metal powders: Atomizcd till powder, 325-mesh Atomized aluminum powder, 325-mesh Reduced copper powder, 100-mesh Electrolytic iron powder, 100-mesh Atomized 70-30 brass powder, l00-mesh The, till powder was molded at various pressures up to 40 tolls per sq. in. This was the maximum, because at higher molding pressures there was considerable extrusion of tin into the die wall, jamming the die plungers. The tin specimens were not -in tered, as this phase of the work was- done merely to see how much a very sold metal could be compressed. The aluminum powder was compressed at various pressures up to 50 lons per sq in. Higher pressures could not be used because of extrusion into the die wall The compacts were sintered one hour at 000 in pure dry hydrogen. The copper powder was molded at vari-ous pressures up to 96 tons per sq. in. One set was sintered at 750°C., another at 050 C. for one hour in pure dry hydrogen. The electrolytic iron powder was molded at various pressures up to 00 tons per sq. in. and sintered, one set at Soo°C and one set at 1300°C for one hour in pure dry hydrogen. Extra 325-mesh specimens were also prepared to study the effect of reduced particle size on grain structure. The brass powder was molded at various pressures up to 96 tolls per sq. in. and silltered for one hour. one set at 65o°C. and one set at 800°C, in pure dry hydrogeu.

Jan 1, 1945

By Cyril Stanley Smith

THE art of metallography is mature and the forms in which various micro-constituents appear are well known. Investigations almost without end have disclosed the importance of the exact manner of distribution of phases on the physical properties and usefulness of an alloy. Surprisingly, however, relatively little attention has been paid to the forces that are responsible for the particular and varied spatial arrangements of grains and phases that are observed. Like the anatomist, the metallurgist has been more concerned with form and function than with origins. In this paper it is proposed to develop the simple concept that many microstructures result from an attempted approach to equilibrium between phase and grain interfaces whose surface tensions geometrically balance each other at the points and along the lines where they meet. From this follows a number of principles which may prove to be of interest to the metallographer and of practical use in explaining failures and in designing alloys for particular service. In general, the discussion will be limited to structures obtained after full annealing. The simple principles do not apply to structures resulting from Widmanstatten mechanisms in precipitation, or to other structures not in local equilibrium and in which lattice coherency is a determining factor. INTERFACIAL TENSION Much has been written by physical chemists about the free energy of surfaces, which manifests itself as a measurable surface tension. Two- and three-phase interfaces in fluids seek a condition of minimum energy and approach a geometrical configuration in which the various forces are in vectorial balance.* Measurement of the angles established between the interfaces when in equilibrium provides a quantitative value for the relative value of the surface forces involved. The case of two fluids meeting at the surface of a solid (of great importance in connection with the flotation of minerals) has often been studied, but there have been few investigations of the equally definite interface between two or more crystals of a single solid phase, or the more complex cases where crystal grains of more than one phase are involved. The principles are best illustrated by considering first the case of two and three immiscible liquids. If, as in Fig I, a liquid, 2, is dropped into a less dense liquid, I, it will form a sphere-if gravity and viscosity can be ignored-for in this shape the interface has the smallest possible area. If these two phases should together encounter a third phase in which they are both immiscible, the geometry will change to become that which gives the lowest total energy for all three interfaces. Thus, if the spherical drop of liquid, falling through r, eventually reaches the interface between liquids 3 and I (we are assuming that the density of 3 is greater than 2, and 2 than I), it will assume the shape of a lens, the angle

Jan 1, 1948

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division: Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and/or commercial value. As to each space in the tabulation, it is either (I) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1938

By P. D. S. St. Pierre

IN recent years the use of high sulphur fuels and charges in steelmaking has necessitated rapid methods of slag control in order to insure the production of high quality steel. Several systems of control have been discussed in the literature, and of these the method described by Philbrook, Jolly, and Henry' has received the most attention recently. In their process the hydrogen ion concentration of an aqueous slag suspension is determined under controlled, but arbitrary conditions. The basicity of the slag may then be derived from a previously established pH-V ratio curve. Thus, by measuring the pH, some indication of the V ratio is gained, from which significant properties of the slag may be deduced. Philbrook et al. made no claims as to the theoretical justification of their treatment, but simply offered it as a rapid means of slag control. Encouraging results caused others to study the method and publish their findings.2-5 Although there was fair agreement on the efficacy of the method, no common parameter was evolved against which pH readings could be plotted. The results of the various determinations were related to such V ratios as CaO/SiO2 and CaO/ SiO2 + P2O5 by some,'-3 while others" plotted against "excess lime." Rivet,' however, found a simple proportionality between the hydrogen ion concentration and the sulphur content of the molten steel beneath the slag. Since slag control in North American practice is largely directed toward the efficient removal of sulphur from steel, Rivet's approach to the problem had the advantage of connecting directly a property of the slag with the impurity being removed. In view of the diversity of parameters used it seemed probable that some fundamental point was being overlooked in seeking a relationship. Examination of the literature revealed that much emphasis had been laid on experimental detail but scant attention paid to the fundamental aspects of the hydrolysis of the aqueous slag suspension. Consequently the present investigation was undertaken with the object of rectifying this deficiency and deriving, if possible, a parameter of general application. Petrographic studies on several matured Canadian open-hearth steel slags have shown that their major constituents are dicalcium and tricalcium silicates set in a complex matrix of iron oxides and ferrites. These phases are shown in Figs. 1 and 2. Free lime is frequently encountered in slags, but is not an equilibrium phase since on continued heating it dissolves forming silicates or ferrites. Thus, it appeared that a study of the hydrolysis of the major phases in steel slags would be profitable. The experimental technique used in the present work was a modification of that described by the other workers.'- Electrical conductivity measurements were also made on the suspensions, since Smith et al." had claimed advantages for this method in their paper on slag control. Experimental Procedure The compounds studied in this investigation were prepared in the laboratory by heating purified oxides

Jan 1, 1954

By Louis Moyd

The Concrete Research Division, U.S. Corps of Engineers, has developed a simple procedure for determining the coefficients of linear thermal expansion of rocks by means of resistance wire (SR-4) strain gauges. Gauges are cemented to the surfaces of specimens, which are then brought alternately to temperatures of 35OF and 1350F. Results are accurate to the seventh decimal place. IN the course of investigations of the thermal properties of various rocks proposed for use as aggregates in concrete structures, a relatively rapid method of determining coefficients of linear thermal expansion was required. A method which proved to be satisfactory for this purpose was developed in the petrographic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss. The method is based on the fact that strain effects in a specimen can be determined by measuring variations in the resistance of an electrical conductor firmly cemented to the surface of the specimen. Equipment for the determination of strain, electrically, has been developed by the Baldwin-South-wark Division of the Baldwin Locomotive Works in Philadelphia. This equipment includes small strain gauges made of coils of resistance wire bonded between thin sheets of paper (SR-4 gauges), and a portable "Strain Indicator" which records variations in the length of the gauges in microinches per inch. Gauges of this type are now in general use for determinations of various mechanically-induced strains, but their use for the determination of coefficients of thermal expansion appears to be a new application. The advantages of the method are that the test specimens may be relatively small and require only a minor amount of preparation, that a large number of tests can be run at the same time, and that the installation and operation of the equipment is relatively simple. The method and equipment described are now in regular use for determining the coefficients of linear thermal expansion of rock samples submitted to this laboratory. Rocks which have been tested include granites, syenites, gabbros, and other igneous rocks, limestones and dolomitic limestones, sandstones, and quartzites. Specimen Preparation: To standardize the conditions of the tests, the rock specimens are sliced by diamond saw into slabs about 11/2x11/4 in. In the case of bedded or foliated rocks, three oriented slabs are cut from the same specimen, and represent, respectively, a direction in a plane of the bedding or foliation of the rock; a direction along the bedding or foliation and at a right angle to the first; and a direction across the planes of bedding or foliation. One of the large surfaces of each slab is lapped for a few minutes with No. 100 abrasive powder to remove saw scars and irregularities. The slabs are soaked in petroleum ether and then dried in an oven to remove all traces of oil picked up in the sawing

Jan 1, 1951

By G. G. Gunther, C. L. Boeke

(Any discussion resulting from presentation at the Los Angeles Extractive Metallurgy Division Meeting will appear in the November 1953 issue.) I. M. Symonds (Cia Minera de Penoles, Monterrey, N. L., Mexico)—This is a most interesting paper describing zinc deleading operations. Mr. Gunther was kind enough to show me his operation last fall. Outside of the excellent results, I was most impressed by the ease of control. I had expected a difficult operation requiring careful control and supervision, but found one requiring little attention. The only disappointing fact of the separation is the poor copper recovery in the concentrate of the deleading float. The final zinc concentrate still has about 3 pct chalcopyrite (assuming the copper is chalcopy-rite) which adversely affects the zinc grade. If the copper mineral is free, the poor recovery is probably due to the high cyanide concentration. Fortunately, about 75 pct of the copper is recovered before the pulp goes to the zinc circuit. Mr. Gunther's remarks about proper cyanide to zinc sulphate ratios cannot be overemphasized. Although our experience has been mostly confined to the conventional Pb-Zn separation, we have found these ratios most important, and more important in the mill than in the laboratory. The laboratory appears to give optimum results over a wider range of reagent control than the mill, especially in regard to the effect of cyanide. In the mill in handling relatively high grade ores, we usually find that ratios of cyanide to zinc sulphate of 1 to 10 or 20 or higher work best. Where there is a substantial amount of chalcopyrite present, it has been noted that cyanide in the range of 0.02 to 0.10 lb per ton of ore is often beneficial in zinc rejection and possibly in copper recovery in the lead concentrate, while larger amounts, say 0.20 to 0.25 lb per ton, will float more zinc and cause a serious rejection of chalcopyrite. On an ore with 15 to 20 pct Zn content, we have had to use 0.8 to 1.2 lb of zinc sulphate per ton of ore with the above cyanide to obtain optimum results. Sometime ago we made a laboratory study following Parral and Santa Barbara practice on an ore which never had a very satisfactory rejection of zinc in the lead concentrate. The results were not encouraging and a mill test was not run. Since then the study has been reopened using fresh zinc concentrate from the mill in the laboratory instead of one made in the laboratory. A reasonably clean lead float from the zinc concentrate was obtained. It has been checked several times and each time the zinc concentrate made in the mill responds and the one made in the laboratory does not. Although undoubtedly some reasonable explanations can be given, it is presented here only

Jan 1, 1953

By Walter Miller

Crude oil stocks were some 10,000,000 bbl higher on June I, 1947, than at any time during 1946 but the extremely heavy refinery runs the last half of 1947 cut crude inventories to approximately the 1946 closing level of 225,000,000 bbl. Many refiners were seriously short of crude oil during the year. This shortage was reflected in numerous advances in the posted price of crude, justified in part as an incentive for more production but more generally due to competitive bidding. Some purchasers of crude, endeavoring to keep their plants running, resorted to the payment, either directly or indirectly, of premiums above the posted price. Another common practice employed by some suppliers of crude oil was to demand refined products in exchange or trade for their raw material. The refined products picture has darkened in spite of record throughputs. Stocks of gasoline and light and heavy fuel oils were uncomfortably low at the beginning of the year and were in general still lower at the close. The rationing of some products, principally gasoline, to dealers and stations? initiated during the year, gained momentum as stocks continued to diminish. The emphasis placed by the manufacturers of oil-burning equipment on the convenience and economy of heating with oil, together with the tight situation in coal, has developed a tremendous demand for burning oils. Consumption of liquefied petroleum gas for domestic and household fuel had more than doubled in 1946 over 1943, and the demand seems to be limited only by the ability of the equipment builders to furnish necessary storage. transportation, and burning equipment. The supply situation is likely to become more acute in 1948. Demand for petroleum products is being pushed to new heights not only by the unprecedented domestic market but by a sudden and drastic upswing in estimates of military and governmental requirements. Additionally, oil exports are running far below the volume requested, amounting to less than forty percent in a recent quarter, and export licenses are reportedly being approved on the basis of urgent need *only. AX recent White House release sees little likelihood that estimated requirements of the sixteen nations participating in the proposed Marshall Plan can be met in full over its projected life—1948 to 1951. Present demand dictates maintenance of refinery operations at the highest possible level and the Bureau of Mines has forecast daily average crude runs in 1948 of 5,265,000 bbl. The Economics Advisory Committee of the Interstate Oil Compact Commission recently estimated the 1948 demand for petroleum products at nearly 6 pct above 1947. They further estimate daily average crude runs of 5,375,000 bbl in 1948, some 2 pct higher than forecast by the Bureau of Mines. Projected demand exceeds supply to the extent that Capitol Hill is reportedly investigating ways of enabling oil companies to act in concert without danger of antitrust prosecution, such as elimination of crosshauls, pooling of products, and lowering of octane.

Jan 1, 1948

By Louis Moyd

The Concrete Research Division, U.S. Corps of Engineers, has developed a simple procedure for determining the coefficients of linear thermal expansion of rocks by means of resistance wire (SR-4) strain gauges. Gauges are cemented to the surfaces of specimens, which are then brought alternately to temperatures of 35OF and 1350F. Results are accurate to the seventh decimal place. IN the course of investigations of the thermal properties of various rocks proposed for use as aggregates in concrete structures, a relatively rapid method of determining coefficients of linear thermal expansion was required. A method which proved to be satisfactory for this purpose was developed in the petrographic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss. The method is based on the fact that strain effects in a specimen can be determined by measuring variations in the resistance of an electrical conductor firmly cemented to the surface of the specimen. Equipment for the determination of strain, electrically, has been developed by the Baldwin-South-wark Division of the Baldwin Locomotive Works in Philadelphia. This equipment includes small strain gauges made of coils of resistance wire bonded between thin sheets of paper (SR-4 gauges), and a portable "Strain Indicator" which records variations in the length of the gauges in microinches per inch. Gauges of this type are now in general use for determinations of various mechanically-induced strains, but their use for the determination of coefficients of thermal expansion appears to be a new application. The advantages of the method are that the test specimens may be relatively small and require only a minor amount of preparation, that a large number of tests can be run at the same time, and that the installation and operation of the equipment is relatively simple. The method and equipment described are now in regular use for determining the coefficients of linear thermal expansion of rock samples submitted to this laboratory. Rocks which have been tested include granites, syenites, gabbros, and other igneous rocks, limestones and dolomitic limestones, sandstones, and quartzites. Specimen Preparation: To standardize the conditions of the tests, the rock specimens are sliced by diamond saw into slabs about 11/2x11/4 in. In the case of bedded or foliated rocks, three oriented slabs are cut from the same specimen, and represent, respectively, a direction in a plane of the bedding or foliation of the rock; a direction along the bedding or foliation and at a right angle to the first; and a direction across the planes of bedding or foliation. One of the large surfaces of each slab is lapped for a few minutes with No. 100 abrasive powder to remove saw scars and irregularities. The slabs are soaked in petroleum ether and then dried in an oven to remove all traces of oil picked up in the sawing

Jan 1, 1951

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division: Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-—several units of continuous productive reservoirs of distinctly different structure and of distinctly dzerent stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and/or commercial value. As to each space in the tabulation, it is either (1) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use 2. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report l,8x,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1937

By H. S. Cannon, F. N. Rhines

The application of a static load to a copper powder compact during sintering at an elevated temperature accelerates the rate of sintering in such a way that a given load induces the same proportional increase in rate for all times of sintering. It is shown that sintering under a load is like creep under a fixed load in that the stress required to accomplish a given degree of densification is proportional to the logarithm of the sintering time. VIRTUALLY all of the theories of sintering that have been put forward within recent years have contained the assumption that the chief driving force of the process is the surface tension resident in the exposed surfaces and internal pores of the compact, or powder mass. An externally applied load might be expected to provide a somewhat equivalent driving force for sintering. It is known that the application of a compressive load, during sintering, hastens densification, but it is by no means clear whether sintering under the influence of surface tension alone and sintering under an applied load are fundamentally similar processes. The present study was undertaken in an effort to obtain an answer to this question and with the hope that the answer may contribute to an understanding of the mechanism of sintering. It has been found that there is a close relationship between sintering and creep processes. Copper powder compacts were sintered in hydrogen at 1000 °C under dead loads of 0 to 165 psi and the progress of sintering was observed by means of density measurements. Using a commercial reduced oxide copper powder, see Table I, cylindrical compacts Yz in. x x in. high were made at a pressure of 12,500 psi. For sintering, these were placed in a cylindrical graphite container into which they fitted snugly. A compressive axial load was applied to the compact through a graphite rod of similar diameter, which rested upon the upper end face of the compact; iron weights, in suitable amount, were placed upon the graphite rod to provide the load. This assembly was encased in a vertical silica tube within a resistance-type furnace capable of maintaining a substantially constant temperature within the working zone. After various predetermined times at temperature, the samples were removed from the furnace and their density was measured by conventional means. The heating-up and cooling-down times have been included in the computed sintering time, using the assumption that the sintering rate doubles for each increase of 10 °C in temperature. The experimental results are presented in Table 11. Upon metallographic examination of the specimens, it was found that there was no apparent change in the shape of the pores as a result of loading, i.e, no flattening, Fig. 1. Substantial contraction away from the container walls was observed in all samples sintered with loads of 10.5 psi and less.

Jan 1, 1952

By H. R. Hendricks

The ore of the Iron King mine, being very hard and having a very fine crystalline structure, presents many problems in milling that are not present in ordinary lead-zinc ores. This very fine crystallization causes much interlocking of minerals and is most prevalent between the gold and pyrite and the sphalerite and pyrite. The recovery of gold is extremely important in the economic value of the ore and therefore constitutes a large part of the metallurgical problem to be solved. All of the gold is free but it has not been observed in any of the mill products except under very high magnification. Some of the gold is tarnished, and this condition also makes recovery difficult. The gold values have been determined to be highest in association with chalcopyrite and arsenopyrite. The silver occurs mostly in association with galena and tennantite. A small amount of native silver has also been observed occasionally. The galena, being softer than the other minerals, frees much better in grinding. Some oxidation of galena is present in the ore, as the non-sulphide lead content amounts to approximately 10 pct of the total lead. Some oxidation of sphalerite is also present in the ore. Microscopic examination of the zinc concentrate shows many grains in the minus 325-mesh to be half pyrite, together with the fact that some of the zinc is marmatite, makes production of a high-grade zinc concentrate very difficult unless recovery is sacrificed. In the grinding, it has been determined that the flotation feed must be maintained at 85 pet minus 200-mesh to free the minerals sufficiently to make the best economic recoveries. Table I illustrates the effect of fine grinding. It shows that the bulk of the recovered minerals is in the minus 325-mesh size and is the part of the minerals that is more readily freed. The pyrite concentrate is not given in the table because it contains practically no minus 325-mesh. Development of Present Flowsheet and Milling Practice The first milling operation started in 1938, with a mill capacity of 140 tons daily, producing a bulk gold-silver-lead concentrate. After several stages of expansion and changes of the mill flowsheet, the mill is currently treating 380 tons of ore daily and three separate concentrates are produced. In order of their importance and value, these are: (I) lead concentrate, (2) zinc concentrate and (3) pyrite concentrate. The present average grade of mill heads is: gold 0.11 oz, silver 4.00 oz, lead 2.50 pet, zinc 7.60 pct, copper 0.22 pct, iron 22 pct and 30 pct insolubles. Specific gravity of the ore is 3.8. During the period when bulk flotation mas practiced, the flowsheet was very simple. The ore was ground fine enough to liberate as much gold, silver and lead as possible. Necessary collectors and frothers were added in sufficient quantity

Jan 1, 1949

By P. W. Barton, A. A. Johnson, E. J. Hughes

THE only systematic work on the effect of carbon on the recovery and recrystallization kinetics of iron so far reported in the literature is that of Venturello et al.1 These workers found that doping high-purity iron so that it contained up to 86 ppm C caused a marked retardation of recovery but had little or no effect on the recrystallization kinetics. Such evidence for an effect as was obtained was inconclusive. In the course of a study of electron-beam zone-refined iron the authors have recently examined the effect of added carbon on the recrystallization kinetics of this material. The amount of carbon added was about 50 pct more than was used by Venturello et 01. and definite evidence was obtained that carbon at this level retards recrystallization. The starting material was taken from a batch of 0.2-in.-diameter Johnson-Matthey spectroscopically pure iron rods which had been further purified by being given three passes at 4 in. hr-1 in a standard MRC electron-beam zone-refining unit. The purity of this material. which was used in two other investigations of the properties of high-purity iron,2,3 was established by an extensive series of analyses. Four laboratories, the National Research Corp., Newton, Mass., the Naval Research Laboratory, Washington, D.C.. the Battelle Memorial Institute, Columbus, Ohio, and the National Physical Laboratory. Teddington. Middlesex, England. carried out analyses for carbon. oxygen. and nitrogen. and in addition a complete mass-spectrograph analysis was carried out at Battelle. In all, twelve analyses were carried out for carbon, seventeen for oxygen and twelve for nitrogen. The amounts of these elements found to be present were 10 * 7, 8 i 5, and 0.9 i 0.1 ppm, respectively. The limits given are rms deviations. Two results, one of 46 ppm of oxygen and another of 31 ppm of nitrogen, were rejected as anomalous. The mass-spectrograph analysis revealed the major impurity to be 25 ppm of tungsten. All of the other elements detected were present in amounts less than 0.5 ppm. Some of the rods were doped with carbon by being immersed in a suspension of carbon in oil, heated in a vacuum at 400°C, and then zone-leveled to make the distribution of carbon uniform. Carbon analyses carried out on three of the doped rods gave a mean value of 130 ± 45 ppm. Some of the doped and undoped rods were deformed 58 pct by swaging and cut into specimens 1/2 in. in length. Isothermal recrystallization experiments were then carried out on them at 575", 600°, 615", 630°, and 650°C, the volume fraction of each specimen recrystallized being measured by a point-counting method described by Hilliard and Cahn.4 The results for the two types of specimens are shown separately in Figs. 1 and 2. In Fig. 3 the pairs of recrystallization curves for each temper-

Jan 1, 1965

By H. R. Hendricks

THE ore of the Iron King Mine, being very hard and having a very fine crystalline structure, presents many problems in milling that are not present in ordinary lead-zinc ores. This very fine crystallization causes much interlocking of minerals and is most prevalent between the gold and pyrite and the sphalerite and pyrite. The recovery of gold is extremely important in the economic value of the ore and therefore constitutes a large part of the metallurgical problem to be solved. All of the gold is free but it has not been observed in any of the mill products except under very high magnification. Some of the gold is tarnished, and this condition also makes recovery difficult. The gold values have been determined to be highest in association with chalchopyrite and arsenopyrite. The silver occurs mostly in association with galena and tennantite. A small amount of native silver has also been observed occasionally. The galena, being softer than the other minerals, frees much better in grinding. Some oxidation of galena is present in the ore, as the nonsulphide lead content amounts to approximately 10 pct of the total lead. Some oxidation of sphalerite is also present in the ore. Microscopic examination of the zinc concentrate shows many grains in the minus 325-mesh to be half pyrite, together with the fact that some of the zinc is marmatite, makes production of a high-grade zinc concentrate very difficult unless recovery is sacrificed. In the grinding, it has been determined that the flotation feed must be maintained at 85 pct minus 200-mesh to free the minerals sufficiently to make the best economic recoveries. Table I illustrates the effect of fine grinding. It shows that the bulk of the recovered minerals is in the minus 325-mesh size and is the part of the minerals that is more readily freed. The pyrite concentrate is not given in the table because it contains practically no minus 325-mesh. DEVELOPMENT OF PRESENT FLOWSHEET AND MILLING PRACTICE The first milling operation started in 1938, with a mill capacity of 140 tons daily, producing a bulk gold-silver-lead concentrate. After several stages of expansion and changes of the mill flowsheet, the mill is currently treating 380 tons of ore daily and three separate concentrates are produced. In order of their importance and value, these are: (1) lead concentrate, (2) zinc concentrate and (3) pyrite concentrate. The present average grade of mill heads is: gold 0.11 oz, silver 4.00 oz, lead 2.50 pct, zinc 7.60 pct, copper 0.22 pct, iron 22 pet and 30 pct insolubles. Specific gravity of the ore is 3.8. During the period when bulk flotation was practiced, the flowsheet was very simple. The ore was ground fine enough to liberate as much gold, silver and lead as possible. Necessary collectors and frothers were added in sufficient quantity

Jan 1, 1947

By Walter Miller

Crude oil stocks were some 10,000,000 bbl higher on June I, 1947, than at any time during 1946 but the extremely heavy refinery runs the last half of 1947 cut crude inventories to approximately the 1946 closing level of 225,000,000 bbl. Many refiners were seriously short of crude oil during the year. This shortage was reflected in numerous advances in the posted price of crude, justified in part as an incentive for more production but more generally due to competitive bidding. Some purchasers of crude, endeavoring to keep their plants running, resorted to the payment, either directly or indirectly, of premiums above the posted price. Another common practice employed by some suppliers of crude oil was to demand refined products in exchange or trade for their raw material. The refined products picture has darkened in spite of record throughputs. Stocks of gasoline and light and heavy fuel oils were uncomfortably low at the beginning of the year and were in general still lower at the close. The rationing of some products, principally gasoline, to dealers and stations? initiated during the year, gained momentum as stocks continued to diminish. The emphasis placed by the manufacturers of oil-burning equipment on the convenience and economy of heating with oil, together with the tight situation in coal, has developed a tremendous demand for burning oils. Consumption of liquefied petroleum gas for domestic and household fuel had more than doubled in 1946 over 1943, and the demand seems to be limited only by the ability of the equipment builders to furnish necessary storage. transportation, and burning equipment. The supply situation is likely to become more acute in 1948. Demand for petroleum products is being pushed to new heights not only by the unprecedented domestic market but by a sudden and drastic upswing in estimates of military and governmental requirements. Additionally, oil exports are running far below the volume requested, amounting to less than forty percent in a recent quarter, and export licenses are reportedly being approved on the basis of urgent need *only. AX recent White House release sees little likelihood that estimated requirements of the sixteen nations participating in the proposed Marshall Plan can be met in full over its projected life—1948 to 1951. Present demand dictates maintenance of refinery operations at the highest possible level and the Bureau of Mines has forecast daily average crude runs in 1948 of 5,265,000 bbl. The Economics Advisory Committee of the Interstate Oil Compact Commission recently estimated the 1948 demand for petroleum products at nearly 6 pct above 1947. They further estimate daily average crude runs of 5,375,000 bbl in 1948, some 2 pct higher than forecast by the Bureau of Mines. Projected demand exceeds supply to the extent that Capitol Hill is reportedly investigating ways of enabling oil companies to act in concert without danger of antitrust prosecution, such as elimination of crosshauls, pooling of products, and lowering of octane.

Jan 1, 1948

By A. N. Holden, J. H. Hollomon

Inhomogeneous yielding during the early stages of plastic flow has been observed in many metals and has long been a subject of controversy. Low carbon steel, when strained at room temperature, exhibits a distinct yield point at which the metal ceases to behave elastically and begins to flow plastically without further increase in stress,† often with an actual decrease in stress from that existing at the yield point. One manifestation of this behavior is the familiar Lüders lines. The extent of the yield point elongation (the plastic strain which results without raising the stress above that at the initial yield point) may be several percent. Several explanations of this type of yielding in steels have appeared in the literature:1-3}; 1. The segregation of carbides or other constituents at the grain boundaries of ferrite forms cell-like blocks which break down at a higher stress than that at which the ferrite alone will flow. 2. The precipitation of various constituents within the ferrite itself in some way blocks initial flow until a higher stress is reached, after which a great deal of flow occurs without further increase in stress. 3. The restraining influence of neighboring, less favorably oriented grains in a polycrystal results in a storing up of energy, which on yielding is sufficient to cause the continued propagation of slip bands on the multiplicity of slip systems available in adjacent iron crystals without increase in stress. 4. Local segregation of carbon atoms increases the stress required for the initial propagation of dislocations. The stress required for further deformation is lower.3 Such an explanation would require the presence of upper and lower yield points in single crystals. Low and Gensamer2 have shown that heterogeneous yielding can be eliminated by removal of carbon and nitrogen from polycrystalline steels by wet-hydrogen treatment. They also demonstrated that the re-introduction of minute amounts of carbon or nitrogen caused a return of the yield point. Observations of the initial flow of single crystals containing small amounts of carbon and nitrogen- should provide a clue to the explanation of inhomogeneous yielding. Previous tests of iron crystals4-6 can not be considered conclusive because it is uncertain whether the carbon and nitrogen were satisfactorily removed by the decarburization technique employed. The purpose of the experiments described herein was to determine whether single iron crystals containing either carbon or nitrogen would exhibit in-homogeneous yielding. Experimental Procedures THE PREPARATION OF SINGLE CRYSTALS All crvstals were formed in the following way. Aluminum killed sheet material 80 mils thick was machined into specimens of the outer contour shown in Fig 1. These mildly tapered specimens were decarburized at 730°C for 16 hr in hydrogen that had been bubbled rapidly through water maintained at 70°. The resultant grain size after decarburizing was approximately ASTM 5. Several stress-strain curves were made of the decarburized niate-

Jan 1, 1950

By A. B. Dyes

In the operation of a water-driven reservoir, a free gas saturation can he established by maintaining production rates fast enough to cause the reservoir pressure to decline below the bubble point. The benefit of such a procedure on the displacement efficiency of the oil by water is illustrated for two types of sandstone samples from one reservoir. Those rock samples showing the poorest recovery to water drive in the absence of a free gas saturation give the most improvement in the presence of a free gas saturation. Employing one type of reservoir fluid (low .shrinkage) the benefit of evolved gas on oil displacement is calculated at several reservoir pressures below the bubble point. This demonstrates the presence of air optimum pressure for water displace,rnent which is .several hundred pounds per .square inch below the bubble point. Displacement of oil at the optimum pressures results in the removal of 7 to I? per cent more oil than would be obtained by displacement at the bubble point pressure. In some instance. this magnitude of increase may be worthy of consideration in establishing the maximum efficient rate of production from many water-driven fields. INTRODUCTION For many years the belief that the use of gas could be combined with that of water to result in a better recovery operation than the use of either of these phases alone has been prevalent in the oil industry. This is evidenced by the several field trials which have employed the injection of gas and water in combination.1.2.v In most cases the small amount of any additional recovery, in combination with the limited knowledge available on the older reservoirs, has left uncertain the influence of gas on recovery in these earlier attempts to combine the use of gas with water. Research studies in recent years have demonstrated through laboratory. floods the magnitude of the benefit of the presence of gas on the displacement of oil from sandstones by water.5,6,7,8,9,10,11 In addition, studies of the distributions of the phases which are present during the displacement process have developed concepts concerning the mechanism by which this benefit is obtained."." It now remains for the engineer to incorporate these findings into the general technology of reservoir operations. It is the purpose of this paper to illustrate that the production of a water-driven reservoir at pressures below the bubble point is one such operation whereby improved oil displacement efficiency can be obtained as a result of gas evolution. The establishment of a gas saturation by evolution of dissolved gas was one of the techniques used by several investigators in the laboratory studies. The possibility of obtaining the benefit of gas evolution in water-driven reservoirs by producing at pressures less than the bubble point has 3150 been pointed out previously." The desirability of this operation has undoubtedly

Jan 1, 1955

By J. B. Chatelain, M. F. Dufour

FLUID jet mills, employing a compressible fluid to grind materials to the subsieve range, was developed in the early 1930's, and the subsequent acceptance of these units was the result of their ability to pulverize solids that, because of physical properties, could not be processed by other attrition methods, such as ball, pebble, and hammer mills. Also, the fluid energy pulverizer is the only grinding device that will discharge continuously a 5-micron or smaller product. Simultaneous ultra-fine grinding and classification is the widest application of this unit. Jet mills may be used to advantage to reduce particle size of solids suspended in liquids, for coating one material with another, and effecting chemical reactions and changes in physical characteristics other than a reduction in size. Materials that can be processed by this grinding method include nonmetallic and metallic minerals, ores, metals, pigments, insecticides, fungicides, pharmaceuticals, plastics, dyes, and numerous other organic and inorganic products. Grinding principles utilized in the fluid mills available on the market are basically the same, the major difference being in the shape of the, grinding and classification chamber. Grinding in fluid jet pulverizers is accomplished by collisions between particles of the material being ground with the energy being supplied by compressed fluids entering the grinding chamber at high velocities. The "Micronizer" is a fluid energy mill employing a relatively flat cylindrical grinding chamber. Fig. 1 shows general construction details. The mill shown is equipped with a venturi type feeder using a compressed fluid to inject the feed into the grinding chamber. The energy consumed in forcing the feed into the grinding chamber against the mill pressure is, in some cases, as much as 40 pct of the total required for processing. Recent improvements, using a compression screw feeder as shown in Fig. 2, can reduce this to 1 or 2 pct of the total energy requirements. Grinding Grinding, as carried out in the. Micronizer involves the action of gaseous jets emerging from nozzles located in the peripheral wall of the grinding chamber. The axes, of the jets are tangential to a circle of smaller diameter than the grinding chamber as is shown in Fig. 1, and the gases entering the chamber maintain a high rotational velocity. The feed introduced into the mill is accelerated by the rotating gases and is thrown to the outside where a portion, coming in the zone of action of a nozzle, is further accelerated tangentially and inward. Violent collisions occur between the particles so accelerated and other particles circulating at a slower rate in a thin band near the periphery. It is estimated over 90 pct of the reduction in Micronizers occur as a result of impact within a fraction of an inch of the orifice. Observations also indicate that size reduction is independent of any interaction with the walls of the

Jan 1, 1952