Search Documents

By E. O. Kirkendall

The investigation reported herein was undertaken to obtain data to supplement those presented in an earlier paper,l particularly for longer times at a higher temperature. This information may further develop our knowledge of the mechanism of diffusion in substitutional solid solutions. Diffusion of solute atoms interstitially dissolved is not difficult to visualize: it can take place without much disturbance of the solvent atoms. The mechanism of diffusion of solute atoms substitutionally dissolved is not so easily understood. Many theories have been advanced. Rosen-hain,2,3 Frenkel,4 Smekal,5 Langmuir,3,6 Steigman, Shockley and Nix,' and Johnson8 all proposed theories to explain diffusion. Langmuir's proposed mechanism consisted of a simple cyclic interchange of atoms involving an interchange in lattice positions of four or more atoms. This mechanism, accepted by the author at the time of his previous publication,1 and apparently quite generally accepted, required a net exchange in positions of both solute and solvent atoms in equal numbers. In other words, the rate of diffusion of the solvent and solute atoms would be the same. That this cyclic interchange in lattice positions of solute and solvent atoms in equal numbers is the only true mechanism of diffusion is denied by the evidence presented in this paper. Experimental Procedure This modification of similar procedure1 will be outlined briefly. The method consisted of the following steps: I. A pure Muntz metal (60.6 per cent Cu, 0.1 per cent total impurities) that was almost all beta brass at 780°C. was chosen. 2. The brass was turned between centers in a lathe to a diameter of 0.5965 inches. 3. After the brass was cleaned, it was electroplated with pure copper to a diameter of about one inch. 4. The sample was heated slowly to 400°C. under reduced pressure and held at that temperature for 4 hr. to remove occluded gases. It was then cooled to room temperature. 5. The sample was heated to 780°C. ± 3°C. and held at that temperature for different lengths of time; then quenched. Samples were cut off each time after quenching. Metallographic samples 1/4 in. thick were removed at I hr., 6 hr., 24 hr., 96 hr. and 701 hr. After 96 and 701 hr. samples of about I in. were removed for X-ray analysis. 6. The metallographic samples were polished on the cross section and photomicrographs were taken. 7. The I-in. samples were polished and etched on both ends. With the aid of a microscope each was carefully mounted in a four-jaw chuck in a lathe, so that they could be accurately bored for an arbor. 8. Turnings were taken for each X-ray sample. After each set of turnings, the sample was heated in an oil bath for about 1/2 hr. at 300°C. It was then etched in 25

Jan 1, 1942

By W. R. Boehme

The laboratory test work compares various 6 x 16 mesh activated coconut carbons using a gold standard solution of 4 ppm dissolved in sodium cyanide. The carbon adsorption rate and maximum loading are measured for different feed solution ionic contaminates: silver, copper, thiocyanate, and ferrocyanide. Conclusions are drawn that among the activated coconut carbons tested, maximum loading and the effects of specific ions varied significantly. The work presented can be applied to 6 x 16 mesh carbon selection tests and specific ion monitoring for industrial carbon adsorption systems.

Jan 1, 1984

By N. Christensen, B. Augland, T. H. Johansen

Samples of an Fe-Nb alloy were brought to equilibriurtr with hydrogen-methane mixtures in the temperature range from 950° to 1050°C, and subsequently analyzed on their carbon contents. The solubility pvoduct L = [%Nb] [%C] may be represented by the equation Approximate solubilities indirectly assessed through hardness measurements have been included from a previous report. These data are shown to be in a fair agreement with the present solubility measurements. IN an investigation based on hardness measurements by de Kazinczy, Ms, and pachleitnerl the molal heat of solution of NbC was estimated to 11.5 kcal per mole. This value was considered rather small, and an investigation using a similar technique was carried out. The results indicated a heat of solution about 35 kcal per mole.2 At this stage it was decided to determine the solubility under conditions of true equilibrium . During the course of this work a similar investigation was published by Smith. 3 His heat of solution, 41.6 kcal per mole, is not very different from the value resulting from the present work (42.5 kcal per mole). Our solubility product, on the other hand, is at considerable variance with that reported by Smith. Possible reasons for these differences are discussed below. Mori, Tokizane, and saheki 7 have studied the behavior of niobium in commercial steels, with special attention to the formation of niobium carbide, nitride, and sulfide. Assuming a carbide composition Nbco.87 based on X-ray diffraction and chemical analysis of residues extracted from Fe-Nb-C-S alloys, the molal heat of solution of niobium carbide was estimated to 35.2 kcal per mole. MATERIALS AND EQUIPMENT The chemical analysis of the materials is given in Table I. Electrolytic iron* was used in the preparation of

Jan 1, 1968

By C. M. Nickerson

It is apparent that repressuring of the oil measures is becoming increasingly important to the oil industry, and is a matter that warrants the best efforts of the petroleum engineer charged with applying this method of operation to a producing property. Considerable attention has been directed to repressuring in various California oil fields, such as Dominguez and Seal Beach, which have served to sell the more progressive operator on this idea and also to keep him sold. The projects that have received most attention are in comparatively young fields where the fluid levels are high, the wells, perhaps, still flowing, where the wet gas production is of considerable volume, and where there is vital need of immediate conservation of gas, which otherwise would be blown to the air. The new State of California Gas Law, which prohibits the waste of gas, has served to interest the oil industry in means of conserving the gas that is now being blown to the air because of lack of markets. This vitally affects the operator in the older, well-depleted oil fields of the state, because in many cases he has a limited market for gas, on account of the flush production from the more active oil fields. While the waste of gas is relatively small in these older fields, such as the Midway-Sunset area, it now attains considerable importance, since under the new State Gas Law it must be put to some bcneficial use. Repressuring in the older fields of California has not received the attention of the petroleum engineers that is warranted by the present situation. This paper was prepared with the view of presenting the salient features connected with repressuring in the well-depleted oil measures of the older fields, and to show what results have already been obtained in these fields by injecting the unmarketable gas into the sands, particularly in the Midway-Sunset field in the San Joaquin Valley of California. Other projects in the older fields of the state offer some supporting data in this connection, such as the Shields Canyon and the Brea Canyon fields. Gas Storage and RepressuRing On account of the lack of market for a large portion of the dry gas produced in certain of the older, well-depleted oil fields of California, the

Jan 1, 1930

By Richard A. Conkling

A shale layer, buried beneath two or three thousand feet of strata, in some instances, will upon folding become thicker in the synelines and thinner on top of the anticlines. This can be accounted for, in part, by the stretching on the crests of the fold and the compressing in the troughs; but this will by no means account for all of it, as is shown in the example herein set forth. It is my firm belief that the rest of the thickness is due to flow. What causes the movement, however, does not concern us here, SO long as there is movement, for this article purposes to show its effect upon the producing area of different sands. It is the author's hope, in this way, to drop a hint or two that may be valuable to the oil geologist, in making estimates of future productions and values of oil properties. An example will be given from property in the famous Gushing Pool in northeastern Oklahoma, where the author has had occasion to make a detailed study before recommending some property to his company, and has then been able to watch the results of this work. The author never mapped the surface structure in this pool, as this had been done by Frank Buttram when he was with the Oklahoma Geological Survey. We are using, therefore, a section of his map in this article for our surface contours. The main east dip comes farther east than this section shows. From the 10-ft. contours in Fig. 1, it will be seen that the surface folding is very slight, but in the contour map of the Bartlesville sand (Fig. 2), which was the greatest producing sand, we see much more complex folding. It seems that the folding becomes greater with the depth. Folding may have started in Middle Pennsylvanian times and continued through the Upper Pennsylvanian which is found at the surface. This may, or may not, have been the cause of the increase of folding with depth. However, the fact that mostly concerns us is the interval of shale between the Bartlesville sand and the Tucker sand. The Tucker is the next productive sand below the Bartlesville. Not enough wells have been drilled to the Tucker sand to make a contour map of it, but

Jan 1, 1917

By Ralph J. Schilthuis, William Hurst

The nature of the forces that are important in producing the oil in the East Texas field and the manner in which these forces are affected by the rate of production have always been problems of outstanding interest. These questions are of great interest to the industry as a whole on account of the economic importance of the East Texas field and to the engineers in particular on account of the unique character and behavior of the field. Subsurface pressure data throughout the field have been collected systematically, so that a quite complete history of the reservoir pressures has been kept as the field has been developed and produced. Subsurface samples of the oil and gas have been taken and these have been examined to obtain data on the physical properties of the reservoir fluids under the actual conditions of temperature and pressure. All of these data have been valuable because they have afforded the basis for a careful study of the means by which the oil is produced. It is the purpose of this discussion first to point out several of the important facts revealed by the data mentioned and then to describe studies that have been made concerning the interpretation of these facts. Reservoir Pressure Data and Properties of Oil The reservoir pressure data on the East Texas field have shown conclusively that the pressures are readily affected by changes in the rate at which the field is produced. This can well be seen in Fig. 1, where the average reservoir pressures obtained from time to time are plotted with the daily production rates and the cumulative production of the field. It is noted that the average reservoir pressure has declined irregularly, depending upon the rate of production, from the estimated original value of 1625 Ib. per sq. in. to the value of 1228 lb. per sq. in. observed for Aug. 11,1934. The decline in pressure has been more rapid at the higher rates of production than at the lower rates. In contrast, the average reservoir pressure has increased, on several occasions, upon reduction of the withdrawal rate from a high value to a lower value. The reservoir pressure data have also shown that a definite gradient in pressure has existed across the field from west to east since the begin-

Jan 1, 1935

By M. J. Saarivirta, P. P. Taubenbla

This paper presents some high-temperature properties of copper-zirconium conductor alloy compared to copper-chromium alloy. Definite superiority of the copper -zirconium alloy over the copper-chromium alloy at high temperatures is shown. RECENT investigations have shown that cold-worked copper-zirconium alloy possesses good room-temperature strength, ductility, and conductivity and maintains most of its strength at temperatures up to 450°C (840°F). As a result, this alloy is now used for many applications, such as commutator segments, resistant welding wheels and tips, rectifier bases, electrical contacts, and so forth. Early investigations1-3 have shown that the maximum solid solubility of zirconium in copper is close to 0.15 pct and the alloy containing Cu-0.10-0.15 pct Zr exhibits the optimum mechanical and physical properties. Results2 have also shown that the alloy has better elevated temperature strength and ductility than copper-chromium and copper-silver alloys. The present investigation was undertaken to learn more about the elevated temperature properties of copper-zirconium alloy and to compare these properties with those of the copper-chromium alloy. WORK PROCEDURE The commercial copper-zirconium alloy, Amzirc was selected for this investigation. Because this alloy is composed of oxygen-free high-conductivity copper and 0.10-0.15 pct Zr, it was believed that possible disturbance from impurities would thus be negligible. Copper-chromium alloys used in this investigation contained 0.40 and 0.70 pct Cr and balance copper. The Cu-0.40 pct Cr alloy was a commercial brand, whereas the Cu-0.70 pct Cr alloy was made from OFHC copper and Cu-5 pct Cr master alloy. It was made in a graphite crucible under argon gas cover and cast. In the preparation of specimens, all three alloys were treated to give the optimum properties; thus the Cu-0.15 pct Zr alloy was solution annealed at different temperatures to determine the desirable solution annealing temperature. It was then cold worked and aged at 375" to 400°C (705" to 750" F). A solution annealing temperature of 1000°C (1830°F) was selected for the copper-chromium alloys because this temperature is widely used in commercial practice. The same alloy was aged at 450°C (840°F) after solution annealing and cold working. It was found that the maximum precipitation hardening of the copper-chromium alloy occurred at this temperature. When aged after solution annealing, the aging temperature was 500°C (930"F) for both alloys. The following properties were determined: 1) Tensile properties as a function of temperature. 2) Effect of solution annealing temperature on high-temperature tensile properties. 3) Stress to rupture strength at 350° and 400°C (660"to750°F). 4) Impact strength. 5) Electrical conductivity and resistivity as function of temperature. 6) Thermal expansion.

Jan 1, 1961

Under the joint auspices of the Illuminating Engineering Society and the University of Pennsylvania there will be given about 20 lectures covering the general principles of illumination and the aspects of lighting practice. They will be held at the University of Pennsylvania in Philadelphia, from Sept. 21 to 28, 1916, inclusive. The subject of illumination of mines will be included in this series, which will be delivered by men selected on account of their qualifications to deal authoritatively with the several phases of the subject. In connection with the lectures there will be an exhibition of the latest developments in illuminating appliances, including lamps, accessories, photometers, together with novel applications of light. There will also be an inspection tour which will include visits to manufacturing establishments, laboratories, lighting companies and notable lighting installations. For further particulars apply to the Illuminating Engineering Society, 29 West 39th Street, New York City.

Jan 6, 1916

By S. Forgeron, W. Shaw, E. L. Zodrow

Trend-surface equations are proposed for volumetric coal estimation in collieries of Sydney Coalfield, Nova Scotia. The statistical technique was first tried on Harbour coal in #20 Colliery investigating resulting residuals for abnormalities. The trend model is accepted as probably being correct as a result of that investigation. Indeed, higher degree polynomial trend- surfaces account for over 80% of the total map variability; these are encouraging statistical results, backed-up by geological knowledge about the coal seam, suggesting that the trend model has economic significance for an off-shore colliery developed to exploit the Harbour coal several kilometers east of #20 Colliery. Specifically, the need for additional offshore drill holes for the new colliery (excepting quality assessment holes) should be considered in light of a developed estimating model for the new colliery. The trend model also finds application in coalfields structurally more complex than Sydney Coalfield.

Jan 1, 1983

By L. W. Pommier, F. B. Brien, A. K. Bhasin

In the field of mineral processing, although many operations are applied to suspensions of ore particles in fluids, there is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. Previously proposed equations, based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids, are exam ined in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. As more knowledge is acquired in regard to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow predictions of conditions to achieve optimum results for engineering purposes. In the field of minerals processing, many operations are applied to suspensions of ore particles in fluids. The differential movement of solids of various sizes and densities in suspensions is of utmost importance to gravity concentration, wet classification, flotation, hydrometallurgy, and pipeline transport of solids. The subject is also of importance to other branches of engineering; for example, those involved with soil mechanics, ceramic slips, and oil-well drilling fluids. There is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The problems encountered in the direct application of the well-known Stokes and Newton's Laws to non-Newtonian systems have been examined in a previous paper.' Equations were proposed based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids. This present paper examines these equations in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. It is thought that, as more knowledge is acquired as to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow prediction of conditions to achieve optimum results for engineering purposes. The purpose of this paper is to make an initial assessment of the nature and magnitude of pertinent suspension variables. In order to avoid too voluminous a document, the examination of kinetics and mechanisms will be omitted at this time. THEORY A Newtonian fluid is defined as a fluid in which the stress is proportional to the rate of strain, 2 i.e.: H = viscosity; see Table I. for list of symbols The following equations are conventionally used to assess the motion of spherical particles moving under laminar and turbulent flow conditions through Newtonian fluids: When these relationships are applied in practice to suspensions, the liquid density is substituted by a composite suspension density, and viscosity is usually taken as that of the suspending liquid or an approximated "apparent viscosity." However, suspensions are non-Newtonian in character3 and thus, more than one viscosity parameter is required to describe their behavior. A number of models have been proposed for non-Newtonian fluids;2,4 among these the simplest is the Ostwaldde Waele or power-law model for incompressible fluids which for one dimensional flow may be reduced to:

Jan 1, 1970

By D. Atkinson, C. Bodsworth, I. M. Davidson

A geometric model of interstitial solid solutions, which has been used previously as a basis for the prediction of carbon activities in Fe-C austenite, is shown to serve also for the calculation of nitrogen activities in Fe-N austenite. The model has been developed to enable predictions to be made of the activities of an interstitial element in the presence of two host atom species. The activities calculated via the model are shown to be in satisfactory agreement with the measured values in the austenite phase for carbon in Fe-C-Co, Fe-C-Cr, Fe-C-Ni, Fe-C-~n, Fe-C-Si, and Fe-C-V alloys and for nitrogen in Fe-N-Ni alloys. The effect of the second substitu-tional solute on the logarithm of the activity of the interstitial element is expressed as the product of a constant mad the atomic concentration of that solute. The constants so derived we related to the thermo-dynamic interaction coefficients which describe the effect on the activity coefficient of carbon of an added solute element. In recent years the thermodynamic activities of carbon and nitrogen in the single-phase austenite field have been determined for iron binary alloys and for several iron-base ternary alloys. In order to extend the use of these measurements, it is desirable to be able to predict with reasonable accuracy the activities of the interstitials at compositions and temperatures other than those which have been measured experimentally. In all the systems studied to date, the interstitial elements do not conform to ideal behavior. Hence, the available data cannot be extrapolated or interpolated using the simple thermodynamic concepts of solutions. Several models have, therefore, been formulated for the purpose of predicting the activity of an interstitial element in the presence of one species of host atom. These models can be divided into the geometric1"5 and energetic6-' types. The former group is based on the assumption that at low concentrations the activity of the interstitial species is determined by a composition-dependent configurational entropy term and an excess free-energy term which is temperature-dependent but independent of composition. The purpose of this paper is to show that the treatment, based on a geometric model, can be extended to enable predictions to be made of interstitial activities in the presence of two substitutional host atom species. THE CONFIGURATIONAL ENTROPY OF MIXING ICaufman5 has shown that the configurational entropy, S,, for a binary solution comprising of a host atom species, A, and an interstitial species, I, can be expressed as: where NI is the atom fraction of the interstitial species, R is the gas constant, and (2 - 1) is the number of interstitial sites excluded from occupancy by the strain field around each added interstitial atom. The number of interstitial sites per host atom, p, is unityg for the fcc austenite solutions considered here. The configurational entropy of mixing for a ternary solution comprising two substitutional atom species, A and B, and one interstitial species, I, can be derived similarly. Let the number of atoms per mole of each of these species in the solution be represented by «a, ng, and nI. From geometric considerations, it is improbable that the addition of a few atom percent of a second host atom species will change the type of sites (i.e., octahedral) in which the interstitial atom can be accommodated in the austenite lattice. At higher concentrations (determined largely by the relative atomic radii of the atomic species present and any tendency to nonrandom occupancy of the host lattice sites) other types of interstitial sites may become energetically favorable. Restricting consideration to compositions below this limit, for 1 = 1 the number of suitable interstitial sites is given by (n + nB). However, if each interstitial atom excludes from occupancy (Z - 1) additional sites, the total number of sites available for occupation is reduced to (n + ng)/Z. The number of vacant interstitial sites is given by: The total number of recognizable permutations of the atoms must include the recognizable, different configurations of the A and B atoms on the host lattice. Assuming that these arrangements are purely random, and are not affected by the presence of the interstitial species, the total number of recognizable permutations in the ternary alloy is given by: The configurational entropy is obtained by expanding, using Stirling's approximation, and collecting like items, as:

Jan 1, 1969

Dr. Wadsworth's discussion of leaching is straightforward and certainly points out some of the critical areas in regards to the fundamental aspects of leaching. I will address myself to the more practical aspects of leaching. As a couple of general comments, very fine particles are often dealt with only when necessary. In many processing applications the sands and slimes are separated with the sand portion being treated by common metallurgical techniques and the slime portion being treated essentially by any technology that will recover some of the values. Ore treatment techniques such as leach/precipitate/float (LPF) have been used in the copper industry to take advantage of leachable copper preferentially reporting to the fine fraction. The second advantage, of course, is the improved metallurgy associated with the treatment of the sand fraction. Cases can be made for sand/slime separations in the aluminum and uranium industry where most of the value reports to the slime fraction and the sand fraction is rejected In the agitated leach systems, fine particles are often the most readily attacked and leached. In dump, vat and in-situ leaching, fine particles cause considerable problems. The fines will tend to restrict the solution flow from portions of the leach feed. This either causes a significantly reduced solution flow or, more probably, the solution will channel, by-passing much of the ore. In either case the result is a decreased metal recovery from ore. The fine particles of principal concern are clays of a flat plate-like shape which can very effectively compact, swell and cause a decreased solution flow. Discrete silica grains or sulfide grains due to their shape, even though they may be very fine, will not cause nearly the problems clays and secondary precipitates can cause.

Jan 1, 1979

By M. E. Wadsworth, T. D. Chatwin

The kinetics of sulfidization of hematite (Fe203) by H2S gas at various partial pressures have been determined over the temperature range of 170° to 500°C. The process was controlled by thin films of pyrite (FeS2) and troilite (FeS) which were protective and formed diffusional layers. At higher temperatures the thermodynamic drive to form FeS2 decreased, and consequently the rate of formation of FeS, decreased. Conditions for the development of thin layers of FeSz consisting of 10 to 100 atomic diameters are presented. Laboratory flotation results on synethetic ores indicate floatability identical to that of pyrite of normal xanthate flotation. The prospect of high-temperature sulfidization of metal oxides using H2S, S, or other sulfur bearing compounds is intriguing as a potential activation process for flotation since the thermodynamics are very favorable for a large number of systems. If the kinetic parameters are sufficiently well understood it may be possible to provide surface sulfide layers a few angstroms thick, thus imparting normal sulfide floatability characteristics to the oxide. For thin layers the total sulfur pick-up would be small except for very high surface area materials but in most cases this sulfur could be readily removed by roasting if necessary. The general reactions for the sul-fidization of metal oxide MxO, to a metal sulfide MpSq using H2S may be written for the three conditions py > xq; py < xq; and py = xq: A large thermodynamic advantage is obtained in many systems because of the relatively large negative free energy of formation of H,O compared to H,S. For the temperature range 2S° to 1500°C &apos; where AFOis the standard free energy and T is absolute temperature. As is evident from Eqs. 4 and 5, the free energy of formation of H ,0 is approximately 35 to 37 kilocalories per mole greater than that for H,S over broad variations of temperature. For oxide-sulfide systems as outlined above, sulfidization may be expected to occur for the conditions: Groups I and 111: that is, if the terms on the right are more negative than those on the left the reaction is expected to occur thermodynamically. The value hFg,(,) is included in Eq. 6 since hFLzs is based upon gaseous S2 rather than the normal reference state, orthorhombic sulfur. The

Jan 1, 1969

By L. L. Brundred

The major portion of the production of the Gulf Coast area, represented by South Texas and South Louisiana, comes from the flanks of well-defined salt domes. This oil, containing an excellent lubricating stock, ranges from 17° to 28° Be. gravity. Some lighter oil is encountered but the life of such fields is, in general, an open question. In fact, there are few light-gravity fields which have proved of much value. In all of the fields water encroachment, or, more properly, water produced with the oil, is a vital factor. After the first head of high-pressure gas is removed, ever-increasing percentages of water appear, and naturally the life of the wells is materially affected thereby. The sands are, as a rule, extremely fine, very soft, and must be carefully excluded from the hole by the use of fine screen to prevent sanding up. All sands are tipped at such extreme angles as to make coring essential for the location of water strata, oil-bearing sands and important shale. beds. Even with modern coring, the correlation of logs is a difficult problem. Due to the fact that the bulk of the oil is refined for its lubricating properties, little attention has been paid to losses by evaporation in the field. This is largely influenced by the fact that the major companies have set a price schedule, showing but two grades, "A" and "B." The average oil company, therefore, does not attempt to use the gas-lift but relies primarily on the air-lift and then only on wells considered to be particularly adapted to its use, namely those capable of producing large quantities of fluid and yet not having sufficient "kick" to flow. Furthermore, as the gas contained in the reservoirs is mostly ricthane such gas being very quickly vaporized and produced in large quantity in the early life of the fields, there is little gas left after the first flush flowing period of the wells. In fact, it is very generally conceded that gas is a precarious fuel to depend on in any of the coastal fields. This situation largely accounts for the fact that air, as the lifting medium, is almost universally used. In the average field, wells are drilled on the flanks of the domes in close proximity to one another, largely on account of the extreme dips of the formation and "town lot" leases, and space to set up machinery and

Jan 1, 1928

By H. L. Miaw, A. M. Gaudin, D. W. Fuerstenau

A quantitative method for evaluating density of slime coatings has been developed and applied to formation of iron oxide slime coatings on quartz and on corundum. Slime coating density is related to flotation recovery and to properties of the electrical double layer at mineral surfaces. IN spite of considerable study, the nature of slime coatings in flotation is still not completely understood. However, phenomena that control floc-culation and dispersion of colloidal systems are now interpreted in terms of electrical double layers.",&apos; Colloids will flocculate even though the particles carry the same charge, but when two dispersed colloids of opposite charge are mixed. flocculation ensues even more rapidly. Analogous phenomena seem responsible for slime coating on minerals in flotation systems. To shed new light on the issue it was considered desirable to devise a tool that would measure slime coatings. The usual method has been to examine photographs of presumably representative surfaces, after. an intervening washing in running water. But such an examination is non-quantitative, and the changes in chemical environment represented by the washing may have removed the slime coatings that existed during flotation. To provide the possibility for a correlation with electrical double layer phenomena, the experiments were made with quartz, corundum, and iron oxide, for which elec-trokinetic data are available.&apos;-" Since the properties of the electrical double layers of these oxides depend on the pH of the solution, pH will be the most important variable. Furthermore, because the zero point of charge for silica, iron oxide, and alumina occurs at pH 3.7, 8, and 9.5, respectively, the relative charge on the slime and mineral can be changed over wide ranges. Because of its practical importance in quartz flotation, iron oxide powder was chosen as the slime. Also, its uniform composition, contrasting color, and ease of analysis make experimentation simple. In this investigation, correlation was sought between the effect on flotation recovery of slime addition and slime coating density. Materials and Methods Details are available in a thesis by Miaw." The quartz was selected from pure Brazilian crystalline quartz, crushed, sized (65/150 mesh) acid-cleaned, washed, and stored in conductivity water. The corundum (synthetic alumina of high purity prepared by Linde Co., Chicago) was crushed, sized (65/100 mesh) deslimed, boiled in nitric acid, washed, and stored in conductivity water. The iron oxide slime, reagent-grade ferric oxide (—400 mesh) from Allied Chemical & Dye Corp., was heated to 160°C, cooled, and stored in a vacuum desiccator. In the electron microscope the slime particles appeared to be about 0.3µ in size, but their large specific surface (87,900 cm per g, by gas-adsorption method, using krypton) suggests that the actual particles are smaller than 0.3r. Had they been perfect nonporous spheres, they would have had a diameter of 0.13µ.

Jan 1, 1959

By M. E. Lombardi

The cost of maintaining the production of an operating oil company is one of the most important, as well as one of the most difficult to estimate, of the various items which go to make up the total cost of producing oil. In the opinion of many operators the cost of drilling and developing new wells, whose, production takes the place of the loss in production through decreased yield of the old wells, is considered an operating expense, for the reason that the total income-producing power of the property is not increased. The cost of these new wells may be added directly to production expense, or it may be charged to capital account, and this account depreciated to the same extent. In either case, after an oil company is on a satisfactory income-producing basis, the money for drilling new wells to maintain production must be taken from the income of the company. Three factors determine the cost of maintaining production: First, the rate of decline in yield of the wells; second, the cost of drilling and equipping new wells in terms of their production; third, the decrease in initial production of new wells as the property is drilled and gas pressure taken off the sands, etc. In order to check theoretical figures for the cost of maintaining production the writer, with the assistance of Reed Bush and Fred Tough, has compiled the following figures. It is necessary first of all to choose a&apos; period of time during which production for the field or territory studied remains fairly constant. The longer the period of time over which this condition prevails, the better. It is also necessary to eliminate or allow for any extraneous condition which may have affected the production returns, such as the shutting down of a large number of wells, the bringing in of a well of exceptionally large yield, the opening up of virgin territory where the flush yield is greater than will be had from new wells in after years, etc. All these conditions are exemplified most simply in the case of the Coalinga field, and perhaps these figures are more truly prophetic than the two other cases given. In applying these figures to the future it is well to assume that the average yield of new wells will constantly de-

Jan 1, 1916

By E. W. Pehrson, J. W. Furness

THE method of presentation in the accompanying charts is based upon the well-known formula: production plus imports minus exports equals apparent consumption. Thus for each area for which data are shown there are two columns of equal height, one representing production plus imports, the other apparent consumption plus exports. Usually no account has been taken of increases or decreases in stocks. All columns and flow lines are drawn to a linear scale which is supplemented by figures showing the actual quantities represented. Owing to the small area occupied by the European countries on the world map it was impossible to show the details of the trade of the individual countries. All of Europe (except Russia), therefore, is shown as a single unit. However, statistics of production and consumption indicated elsewhere on the charts show the degree of self-sufficiency enjoyed by the major European powers.

Jan 1, 1936

By M. J. Humenick, K. Garwacka

A laboratory experimental research project was conducted to evaluate the use of chlorine for the oxidative destruction of residual ammonia that may remain in ground water after in-situ uranium solution mining operations. The work tested the idea of injecting high strength calcium hypochlorite solution into the mining zone to convert ammonia to nitrogen gas as a final cleanup process for ammonia removal from the ground water system. This paper details ammonia removal efficiency as a function of chlorine dose, reactant, and product material balances, and how the concept may be used as a final ground water restoration process.

Jan 1, 1985

By D. A. Elgillani, M. C. Fuerstenau, J. D. Miller

Adsorption of lead and ferric iron on quartz and alumina is presented as a function of pH. Only the hydrolyzed species of these metal ions, FeOH++ and PbOH+, adsorb significantly on each of these minerals. Zeta potentials of quartz were measured as a function of pH in the presence of various additions of aluminum, lead, and magnesium salts. Sign reversal occurs at the pH values where significant concentrations of hydroxy complexes are formed. Models of adsorption are presented in the absence and presence of collector. The mechanism of adsorption of metal and collector species in the activation of nonmetallic minerals is still the center of considerable discussion in spite of the extensive study given this system. Until recently, the view was widely held that hydrated metal ions were responsible for this phenomenon. This fact is surprising, since it had been shown that the pH range in which flotation is effected corresponds to that in which metal ion hydrolysis occurs.&apos; Additional support of this concept was pro vided by the work of Wolstenholme and Schulman in another system.&apos; Later work has shown that hydroxy complexes of metal ions are the active species. These studies have also indicated that basic aqueous complexes of metal-collector may be necessary for flotation.3-7 Depending on the molecular weight of the collector, formation of these complexes may occur before or after precipitation of the metal-collector salt has occurred. Ion pair formation can occur when low molecular weight collectors are involved because relatively high concentrations of metal hydroxy complex and collector can be present in solution before precipitation occurs. This is not the case when high molecular weight collectors are used. A model of aqueous complex adsorption has been presented6,7 in which it has been assumed that adsorption occurs by the formation of water from adsorbed hydroxyl and hydrogen of the hydroxyl contained in the complex. Other authors8 have suggested that hy-droxy complexes are involved in these systems but that collector adsorption occurs by replacement of the hydroxyl of the adsorbed metal hydroxy complex with a fatty acid anion. All of these investigations have involved mineral surfaces that were negatively charged so that it is not possible to state with certainty whether hydrated metal ions or hydroxy complexes are the active species in this system. Use of a positively charged mineral should be helpful, however, since the hydrated metal ion will be repelled from this surface. On the other hand, if the hydroxy complex adsorbs by splitting out water, surface charge should have no effect because of the free energy decrease that the system will experience when water is formed. In this regard, sapphire is well-suited for study, since its surface is positively charged until approximately pH 9. Electrokinetic studies of quartz in the presence of various metal ions should also be useful in establishing the mechanisms of adsorption in these systems. That is, if the hydroxy complexes adsorb by water formation, drastic changes in the zeta potential should occur in the pH range in which hydrolysis occurs. In this view, adsorption of ions of widely different hydrolysis characteristics on both sapphire and quartz was measured. In addition, zeta potentials of quartz were measured as a function of pH in the presence of various metal ions and compared with flotation responses obtained under similar conditions. Experimental Materials and Techniques Reagent-grade aluminum, ferric and magnesium chlorides, and lead nitrate were used in this investigation. Adjustments in pH were made with reagent-grade HCl or KOH. Conductivity water, made by passing distilled water through an ion exchange column, was used in all of the experiments.

Jan 1, 1971

US 4,181,588 - Direct extraction of lead from lead sulflde ore. Ore is leached with a solution of ferric chloride and sodium chloride. The leach liquor is filtered to remove sulfur and gangue, then cooled in a crystallizer to precipitate lead chloride The slurry from the crystallizer is subjected to electrolysis to deposit lead chloride on the cathode plate. Solution from the electrolysis cell is used in the leaching step. M.M. Wong and F.P. Haver, assigned to US Secretary of the Interior Jan 1, 1980. 6 pp. (204-115). Filed: 1-4-79 (1,026).

Jan 1, 1982