Search Documents

By H. W. Smith, A. K. Bjerring

A nonlinear dynamic model for a flotation cell is developed, using a number of simplifying assumptions, the most important of which is that of essentially complete liberation in the feed material. Using this model, a complete dynamic model for a flotation circuit is developed and calibrated against steady- state process data. The dynamic response of the circuit to disturbances in input feed rate and composition is simulated, as is the response of a linearized and simplified model on which control design might be more easily based. Preliminary results indicate the practicability of the modeling technique. However, difficulties in matching steady-state operating conditions in one process stream, and the apparent importance of recycle streams as indicators of process operation, indicate that inclusion of at least one species of middling particle in the model should be considered.

Jan 1, 1969

By Chester O. Ensign

Results of the application of geologic knowledge to grade control have been remarkable. Grade reduction from dilution has been diminished from greater than 9% at the time of the program's beginning to about 2% at present. This has resulted in an increase of about 1.8 lb of copper per ton of ore mined and has made a substantial contribution to earnings at White Pine during the past two years. Even more improvement is expected in the future. The White Pine orebody, situated in the southwestern portion of the Keweenaw peninsula of upper Michigan, is a gently dipping stratiform or bedded deposit. Copper distribution is stratigraphically controlled with higher values being confined to specific beds in the ore column. Room-and-pillar mining is practiced. Mining technique and geologic characteristics present a special array of problems in controlling the grade of ore.

Jan 4, 1964

By K. A. Natarajan, I. Iwasaki

The effect of poisoning on the behavior of platinum electrodes in redox potential measurements in metallurgical systems was studied in the presence of such inorganic surfactants as cyanide and sulfide and such organic surfactants as dodecylammonium acetate, trimethyldodecylammonium chloride, potassium ethyl xanthate, and potassium diethyl dithiophosphate (Aerofloat®). These chemical species represent, more or less, typical constituents encountered in leaching, flotation, and sewage treatment systems. Triangular wave voltammetry was used as the experimental technique to study the nature of poisoned surfaces. Among the species studied hydrogen sulfide and dodecylamine were found to form a resistant surface film affecting charge transfer. Platinum electrodes appeared to have a weaker tendency to adsorb sulfide species in alkaline pH ranges, while cyanide, xanthate, and dithiophosphate affected the normal electrode behavior differently. Possible methods of reactivation of a poisoned electrode by mechanical cleaning are suggested.

Jan 1, 1974

By Linda P. Bono

Some mining engineers are pursuing their destinies in places far removed from what they might have envisioned back in the classroom. The path they follow to work each day may wind down Wall St., Park Avenue, LaSalle, or Market; their offices are in modern skyscrapers which offer all the amenities-air conditioning, thick carpets, attractive decor, and executive lunchrooms, to name just a few. The papers on their desks are a combination of financial figures and feasibility studies. But even in these surroundings there are indications of what these men do and where their professional interests lie-minerals are everywhere, from vast collections to one symbolic paperweight. . . there are sometimes specks of dirt under fingernails from a recent on-site inspection, belying the traditional banker's garb. . . and there are the wistful comments about finding it necessary to get out in the field.

Jan 9, 1978

By E. H. Lovitt, A. C. Skerl

After nine years of continuous operation it is a good idea to take stock of the geological concepts that guide the working of a mine. This is a welcome opportunity to discuss the Lovitt gold mine, which has been a challenge in both the geological and operational fields. The occurrence belongs to the extensive group of epithermal gold-silver deposits once worked so vigorously in the western states, Hungary, and New Zealand and still producing in Central America and the Philippines. These deposits are characterized by a relatively shallow vertical range up to 2000 ft, and often much less, and by bonanza orebodies of even more limited range. The area in which they occur is frequently widespread, so that exploration must be directed along and across the strike of known favorable structures in search of repetitions.

Jan 9, 1958

By C. E. Wood

THIS paper is a brief report of experimental work undertaken to determine whether barium oxide in any quantity increases the desulfurizing action of blast-furnace slags. Industrial furnace operation with slag containing small quantities of barium oxide, referred to later, interested S. A. Sanford of the Commercial Chemical Co., Youngstown, Ohio, to conduct experiments to furnish comparative results on desulfurization with normal slag and slag containing small quantities of barium oxide. The U. S. Bureau of Mines agreed to assist on the problem because of the possible saving in fuel if the desulfurizing action of blast-furnace slag can be substantially increased, also because the experiments would yield new information on sulfur elimination in general, a matter of economic importance in furnace practice. A more complete and fundamental study of desulfurization of iron by slag is in progress.

Jan 1, 1929

By A. Thies, Wm. B. Phillips

1. Introductory Remarks.—The Haile Gold Mine is in Lancaster county, South Carolina, 3 1/2 miles east of Kershaw station on the Charleston, Cincinnati and Chicago Railway. It was first opened about, the year 1832, and since that time has passed through various fortunes. Many different operations have been practiced here for extracting the gold : panning, grinding in Chilian mills or arrastras, stamping, the Designolle process, dry-crushing, and finally the Thies process of barrel-chlorination, which has now been in successful use for 2 1/2 years, and by which 36,000 tons of ore have been treated profitably. The Thies process is in brief the treatment of dead-roasted auriferous concentrates (pyrite, sometimes also chalcopyrite, as at the Phœnix mine, Cabarrus Co., N. C.) with nascent chlorine, without ' artificial pressure or exhaust, in lead-lined iron cylinders; the throw-

Jan 1, 1891

By J. L. Wilson, D. L. Emmons

The Tucker Hill perlite deposit is located in the northwestern portion of the Devils Garden lava field in Lake County, south-central Oregon. The perlite occurs in the chill margin of a late Miocene composite rhyolite lava dome that exhibits distinct cooling zonation. The chill margin is composed of an outer glass envelope, which contains commercial-grade granular and vesicular perlite, and an inner glass envelope, which contains onionskin perlite of local commercial quality. Glassy rhyolite and rhyolite compose the lava dome core. The entire dome complex encompasses at least 5 km2 (2 sq miles). Expansion tests in commercial-scale furnaces indicate that the perlites are suitable for a wide range of applications and compare favorably with commercial perlite ores. The large tonnage deposit appears competitive for markets in the midwestern and upper northeastern states, and the Pacific Northwest of the US.

Jan 1, 1986

The phosphate pebble-bearing matrix in the Florida Phosphate Pebble Field has physical properties which make it readily adaptable to hydraulic transportation methods employing solids-handling pumps and pipelines. The abundance of water available, a practically flat terrain, low costs per ton-mile, and beneficiation of the matrix by agitation while being pumped have contributed to the popular choice of hydraulic transportation. Phosphate pebble mining in Florida, begun in the 1860's, first used high pressure water and solids-handling pumps for overburden removal about 1900. Removal of the average 25 ft of overburden was followed by hydraulic mining of the matrix, with 6-in. and 8-in. pumps handling 50 to 100 cu yds per hour being moved along the floor of the pit as they were advanced toward the face being undercut and slurried by hydraulic guns.

Jan 3, 1961

By John V. Beall

THIS is not simply the story of how a water filled shaft was developed into a million-ton- a-year producing mine in the space of four critical years, although it is reason enough for telling it, but it is also the saga of an engineering achievement in which knowledge nurtured by years of experience in coal and ore mines was blended together and the best from each type of mining selected. The entire system of mining was detailed on maps by the mining engineering department before the shaft was unwatered, and subsequent development followed these plans nearly to perfection. The selection of machinery was particularly critical as it was necessary to push production from only a few headings in the early stages of development and metal mine machinery was being used in a coal panel-system of mining.

Jan 12, 1950

By Charles T. Holland

This discussion is concerned with those comparatively infrequent bumps that eject material from the failed mass with enough energy to wreck heavy machinery and seriously injure or kill people. In such cases there is a loud report, and the pressure waves set up in the mine atmosphere wreck ventilation controls several hundred feet from the site of the failure. Vibrations are induced in the earth's crust which may be detected several miles from the point of origin, and explosive gases may be released in large quantities.* Usually a dense suspension of dust is produced from the failed mass, together with dust placed in suspension by the resulting air blast. These rock bursts or bumps have also been called mountain shots, bounces, pillar bursts, and crumps. Such occurrences, when extensive, are serious catastrophes, and may force abandonment of the mine.1

Jan 9, 1958

By D. F. Atkins, B. A. Rogers, E. J. Manthos, M. E. Kirkpatrick

A phase diagram of the uranium-columbium alloys is presented. The apparatus and the procedures used in obtaining the data are described. Data from which the diagram was drawn are given in tabular and graphic form. THE use of uranium in the production of energy from nuclear fission has given considerable im- petus to the investigation of the metal and its alloys. Accordingly, information concerning the phase diagrams of binary alloys of uranium with other elements is of interest to metallurgists engaged in nuclear-engineering activities. As a contribution to the knowledge of the binary alloys, the authors have attempted to establish the diagram of the uranium-columbium system. The reports of laboratories engaged in work for the Manhattan Engineering District and the U. S. Atomic Energy Commission contain a number of references to work on uranium-columbium alloys.

Jan 1, 1959

By Bradley Stoughton

THE importance of magnesium alloys as engineering materials has increased rapidly in the past few years. The most important properties of magnesium alloys are their lightness and strength, which result in their. extensive use in aircraft and automobile construction. Recent progress in the metallurgy of magnesium seems to offer hope of the production of the pure metal at a reasonable cost. The use of magnesium would doubtless increase greatly if it could be produced at a cost comparable with that of aluminum. AA preliminary survey of the magnesium-base alloys shows that the most promising from a practical standpoint are magnesium-aluminum and magnesium-zinc as binary alloys, and magnesium-zinc-aluminum as ternary alloys. The research reported in this paper is a preliminary study' of binary magnesium-aluminum and magnesium-zinc alloys, as an introduction to a series of further investigations.

Jan 2, 1926

By S. F. Ravitz, S. R. Zimmerely

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine.

Jan 10, 1950

By Oberlin Smith

The use of cast-iron tools, with chilled cutting-edges, for lathes, planers, boring-mills, etc., is not, as Gar as I can learn, very extensive in the United States, or perhaps in England and other parts of Europe. I have, however, no data to guide me in regard to foreign

Jan 1, 1891

By William G. Kegel

Problems involved in putting the gob back underground in modern deep mines we dealt with. In particular, the problems associated with haulage of the gob back to the mine, the blown gob method of dispersion underground, and handling the refuse as slurry are discussed. Some alternative methods of disposal are presented.

Jan 1, 1976

By P. F. Allen

WITH capacity of 51,000 tpd, the Morenci concentrator produces approximately 49,000 tons of tailing for final deposition. Disposal involves distribution of thickened tailing to dams in such a manner that solids can be used for dam construction and water can be impounded for reclamation. During early operation, although tonnage treated was lower, it was necessary to use orthodox disposal practices in the areas available for tailing. Trestles mounted on a series of dams, constructed of borrow material, carried the pipelines from which tailing were spigoted behind the dams. When adequate disposal areas were finally established, it became desirable to look for more efficient methods. The idea of placing the distribution pipe or manifold directly on the crest of the dam was advanced in 1945. After a period of testing, that procedure in modified form replaced the older trestle arrangement. Marked economies resulted, and time required to prepare dams for succeeding storage cycles was greatly reduced. The tailing disposal area for the Morenci concentrator lies south and southwest of the concentrator building. Ample storage space is available. A wide valley contains three sharply defined ravines lying on an average slope of 4 pct. The more central of these ravines, and the largest of the three, is known as Morenci canyon, which provides substantially more tailing storage area than the other two. Stargo canyon lies to the west; the other is appropriately named East canyon. Total area of the tailing disposal site is nearly 31/4 sq miles, or about 2000 acres. The storage area in use was somewhat more than 850 acres at the end of 1954, or 16 acres per 1000 tons of tailing to be stored daily. At the present time none of the east side dams are in regular use but they are available in emergency. There are five dams on the west side (in Morenci and Stargo canyons) as well as two auxiliary dams adjacent to No. 4 West and No. 5 West. This has made it possible to concentrate men and equipment in a smaller area with consequent savings in both manpower and machinery. Tailing Thickening: Tailing from the flotation process reaches the thickeners with a solid content of about 18 pct. The launder carrying this pulp is subdivided at a central point into seven launders carrying a proportional share to each of seven tailing thickeners, which are located in Morenci canyon close to the concentrator. Five of these thickeners are 300 ft diam and two are 325 ft diam. Thickeners are of the peripheral traction type and rakes travel at the rate of one revolution in 37 to 39 min. The entire installation provides 500,000 sq ft of settling area, or approximately 101/2 sq ft per ton of tailing to be thickened daily.

Jan 1, 1957

By C. A. Heiland, Tripp R. M., Dart Wantland

This paper serves to illustrate the application of geophysics to a virtually abandoned mine properly, an application that led to the discovery of an ore body and thus afforded an Opportunity to cOmpare subsequent geologic findings with geophysical data. The work herein described represents, however: more than mere ''case history." It demonstrates that it is possible to obtain satisfactory results by simple means and relatively inexpericnced personnel. The geophysical surveys were made by students as a part of their field assignments in the course of their regular training, and were supervised by Dart Wantland, J. E. Hawkins and R. Maurice 'Tripp. In the course of several seasons an appreciable amount of material was accumulated, which gave graduate students an opportunity for special studies. In this connection, the contributions by L. Massé, R. C. Hyslop, and J. E. Hawkins deserve special mention. The property owners cooperated wholeheartedly in the work, and special thanks are due messrs. J. F. Johnson and S. E. Zelenkov, of the American Smelting and Refining Co., for their interest and for permission to utilize the results of their development work for this publication. Location and Geology The Malachite mine is situated on the northcrn slope of Bear Creek Canyon, 4 miles northeast of Evergreen, I½ miles northwest of Idledale, and 4% miles west northwest of Morrison, in Jefferson County, Colorado. The location (Fig. I) is north of the center of set. 30, T. 45, R. 70 W., at an elevation of about 7500 ft, above sea level, Near the mine the terrain slopes rather uniformly southward at an angle of about 180 pigs. 3 and 7). The geology of the Malachite mine area has been described by J, underhill,' W, Lindgren,2 and J. Boyd.3,4 A map showing surface outcrops and mine workings appears in Fig, 2. the Malachite mine is in an amphibolite belt enclosed in gneisses and schists of the Idaho-Springs formation (probably early Algonkian age). The highly contorted beds are nearly vertical and strike slightly north of west. A series of granite-pegmatite dikes have been intruded almost at right angles into the gneisses and schists and doubtedless are postmineral. While most of the formations are exposed at the surface, a part of the 'lope is covered by slide rock and float, and in the eastern portion by alluvium and creek fill. A quartz-diorite dike cuts through the amphibolite schists at a small angle with nearly vertical dip. The copper sulphides, developed in this dike by magmatic segregation, occur in lenticular form. As far as the mine workings have revealed, the ore lenses are often discontinuous in depth and

Jan 1, 1946

By Tripp R. M., C. A. Heiland, Dart Wantland

This paper serves to illustrate the application of geophysics to a virtually abandoned mine properly, an application that led to the discovery of an ore body and thus afforded an Opportunity to cOmpare subsequent geologic findings with geophysical data. The work herein described represents, however: more than mere ''case history." It demonstrates that it is possible to obtain satisfactory results by simple means and relatively inexpericnced personnel. The geophysical surveys were made by students as a part of their field assignments in the course of their regular training, and were supervised by Dart Wantland, J. E. Hawkins and R. Maurice 'Tripp. In the course of several seasons an appreciable amount of material was accumulated, which gave graduate students an opportunity for special studies. In this connection, the contributions by L. Massé, R. C. Hyslop, and J. E. Hawkins deserve special mention. The property owners cooperated wholeheartedly in the work, and special thanks are due messrs. J. F. Johnson and S. E. Zelenkov, of the American Smelting and Refining Co., for their interest and for permission to utilize the results of their development work for this publication. Location and Geology The Malachite mine is situated on the northcrn slope of Bear Creek Canyon, 4 miles northeast of Evergreen, I½ miles northwest of Idledale, and 4% miles west northwest of Morrison, in Jefferson County, Colorado. The location (Fig. I) is north of the center of set. 30, T. 45, R. 70 W., at an elevation of about 7500 ft, above sea level, Near the mine the terrain slopes rather uniformly southward at an angle of about 180 pigs. 3 and 7). The geology of the Malachite mine area has been described by J, underhill,' W, Lindgren,2 and J. Boyd.3,4 A map showing surface outcrops and mine workings appears in Fig, 2. the Malachite mine is in an amphibolite belt enclosed in gneisses and schists of the Idaho-Springs formation (probably early Algonkian age). The highly contorted beds are nearly vertical and strike slightly north of west. A series of granite-pegmatite dikes have been intruded almost at right angles into the gneisses and schists and doubtedless are postmineral. While most of the formations are exposed at the surface, a part of the 'lope is covered by slide rock and float, and in the eastern portion by alluvium and creek fill. A quartz-diorite dike cuts through the amphibolite schists at a small angle with nearly vertical dip. The copper sulphides, developed in this dike by magmatic segregation, occur in lenticular form. As far as the mine workings have revealed, the ore lenses are often discontinuous in depth and

Jan 1, 1946

By M. N. Dunlap

This article summarizes the successful incorporation of a flash-flooding stream into the tailing-disposal system at the St. Joseph Lead Company's Federal Division mill, in St. Francois County, Missouri. The mill was built in 1906, by the Federal Lead Co., as its No. 3 mill for the concentration of southeastern Missouri lead ores, and damming Davis Creek was first considered in 1908. Plans were made also in 1925 and in 1937. Dam layouts varied from a reinforced concrete structure to a barrier built of tailings alone. .All were abandoned because of liability that would be incurred by flash-flood rupturing of an incompleted dam. By 1942 mill capacity had reached 12,000 tons daily and increasing tailing-disposal costs again focused attention on the Davis Creek basin. This time the problem of riskless dam building was solved. Moreover, most of the items that appeared in the answer were materials that normally required wasting and the major portion of labor involved performed functions that it mould normally have done, without constructive benefit, elsewhere. The new layout also made possible advantageous changes in mill-water supply pumping; static head being reduced from 514 ft to 9; ft, friction head from 4900 ft to 2860 ft, and pumping can be done now at periods of low power demand. The following facts about the Davis Creek watershed explain the 36-year reluctance to reach these, and other, benefits. Size: 3600 acres. Outline: roughly pear-shaped, 21/2 by 3 miles at the largest dimensions. Topography: mostly hill land with steep valleys. Relief: 760 minimum to 1153 maximum. Maximum rainfall: 3.36 in. per hour. Permanent water: none natural. Now 2200 gpm discharged through 16-in. drill hole from mine pumps underground. Geology: the 17 acres near dam centerline is Bonne Terre dolomite covered with sand and gravel eroded from Pleistocene beds that cap some of the hills. The remainder of the pond basin is on Davis shale. Soil cover: mostly second-growth timber with some abandoned fields; all subject to careless burning, which reduces water-retaining ability. Flood history: flash-flooding that had taken at least one life. Downstream values: two railroad bridges before creek intersection with Flat River. Immediately below confluence, a highway bridge, a low-water crossing, a few business establishments and several blocks of residences. In July 1942 the following segments of an ingenious plan were put into operation. A ditch 270 ft long, 16 ft wide and 51/2 ft deep was excavated to bedrock in the gravelly soil along the proposed dam's centerline. This excavation, which exposed many gravel-filled channels, was run full of slimes drawn from a riser set in the top of an adjacent tailings-disposal

Jan 1, 1949