Search Documents

By D. E. Marks, Arnold, C. W, R. J. Robinson, A. E. Hoffmann

The efficiency of operation of a fixed-bed adsorption unit is infEuenced both by the absolute adsorption capacity of the bed and by the rate of adsorption. This paper describer studies of adsorption rate which were conducted in an experimental unit designed such that conditions existing in the treatment of high-pressure natural-gas mixtures could be duplicated. Variables investigated included pressure, temperature, gas composition, adsorbent particle size, depth of packed bed and gas velocity. The adequacy of a simplified mathematical model for predicting the observed phenomena was tested. A correlation is preserited which relates adsorption rate to the process variables stlldied. This correlation is useful in combination with the matheinatical model. INTRODUCTION Of the techniques available for contacting adsorbent particles with fluid streams to be treated, fixed-bed adsorption columns offer definite advantages in simplicity and ease of operation. As a result, they are often used in preference to others for such petroleum industry applications as dehydration and purification of natural gas and hydrocarbon recovery. Fixed-bed adsorption units usually consist of two or more towers filled with a desired adsorbent and operated in a cyclic manner. While one is being used to process the main flow stream, the others are undergoing regeneration to remove the adsorbed phase. When the tower on stream becomes saturated with the preferentially adsorbed material, the roles of the towers are switched, and the freshly regenerated tower is placed on stream. Cacle duration is determined by the bed capacity under the process conditions and by the flow rate through the bed. The sharpness of separation which can be effected is a function of both the absolute capacity of the bed and the rate of adsorption in the bed. The effect of rate for a particular set of conditions is evidenced by the sharpness or diffuse-ness of the adsorption front as it advances through the bed. Since data needed for design of adsorption units to treat high-pressure natural-gas systems were not available, an experimental program was designed to investigate the effects of different variables upon adsorption rate in fixed beds. In the present paper, effects of gas composition, column length, temperature, pressure, adsorbent particle size and flow rate (actual linear flow rate of the gas) are shown, and utility of a simplified mathematical model for describing the process is discussed. As gas enters the top of a cool, clean bed of adsorbent, preferentially adsorbed materials are stripped from the main flow stream by the uppermost particle layers. As these layers become saturated with a particular component, new supplies of this component are carried further down the column until fresh adsorbent is encountered. An adsorption wave thus moves through the column as material is supplied to saturate succeeding elements of the bed. Adsorption from a Multicomponent gas stream occurs as a succession of such moving waves corresponding to the different components in the gas. The leading edge of an adsorption wave for a component of a natural-gas stream moving through a bed of a common commercial adsorbent such as silica gel would be sharp but for the influence of certain broadening fac tors. These factors include a nonuniform velocity profile in the bed, longitudinal dispersion or mixing in the main gas stream, and the time required for a molecule to migrate from the main gas stream and be adsorbed at a site within the body of an adsorbent particle. If packing is uniform and the ratio of column to particle diameter is greater than approximately 15:1, the first factor is relatively unimportant' Longitudinal mixing is of importance only for the case of moderately high mass transfer with extremely slow flow rates.' The sharpness of an adsorption front, therefore, is, primarily a function of the rate of adsorption or the time required to saturate a particle of zdsorbent. Two methods for defining adsorption rate are used in this work. The first is a normalized or relative rate which describes the rate of saturation of a differential element of the packed bed. This can be measured by observing the time required for the concentration of the preferentially adsorbed material in the effluent gas from the bed to rise from zero to a value equal to that in the inlet gas stream. The second definition describes the absolute rate of mass transfer from the gaseous to the adsorbed phase. This definition is used in a mathematical description of the adsorption process. If the concentration of a component in the gas strcam leaving an adsorption column is measured and plotted as a function of time, a curve such as that shown in Fig. I results. It is seen that for a period of time the effluent gas is devoid of the component under consideration. As the bed approaches saturation, a small percentage of this material will appear in the effluent gas. The concentration will then rise with time, or increasing cumulative gas flow, until it is equal to that in the inlet gas stream. If adsorp-

THE only asbestos mine in the Middle East is on the Island of Cyprus, high in the Trodos Mountain village of Amiandos. The mine is owned by the Tunnel Asbestos Cement Co. Annual output is some 18.000 tons of short fibre in the 4-T. 4-Z, and 5-R grades.

Jan 9, 1953

By Oliver Bowles

GLASS razor blades, glass chairs, and marble window panes attest that creative genius was still active in 1935. Many less striking, though doubtless more important, developments are to be recorded for the nonmetallic mineral industries, and not the least of them is the establishment of an Industrial Minerals Division in the A.I.M.E. under the able leadership of Samuel H. Dolbear, Chairman. Thus the nonmetallics are rightly granted equal dignity with metals and fuels in the category of mineral industries. The brief review of progress that follows merely touches the fringe of important developments in this broad field.

Jan 1, 1936

By Charles E. Locke

IN gathering material for this review the aid of the individual members of the Milling Committee was invoked and the assistance received is hereby most grate- fully acknowledged. The replies were much alike; almost everyone stated that in 1932 his operations had been cur- tailed or stopped entirely, that the only activity and progress were in milling gold ores, and that the Hadsel mill' looked like a coming machine in the crushing and grinding field. However, further inquiry and search have shown that the year was not quite so barren of developments as the foregoing statement would indicate.

Jan 1, 1933

By AIME AIME

FOUR separate groups of conveyors are installed in the Morenci Reduction Works as follows: (1) Ore-handling conveyors from the primary crushing plant to the coarse ore bin, from the coarse-ore bin to the secondary crushing plant, and from the secondary crushing plant to the ore bin in the concentrator plant. (2) Conveyors in the mill section of the concentrator plant. (3) Conveyors handling concentrate from the filter plant to the bedding plant, and from this plant to the smelter. (4) Conveyors handling flux and custom ore in the smelter crushing plant and to the bin at the bedding plant.

Jan 1, 1942

By H. F. Ramstad, F. D. Richardson

The equilibria (a) SiOz +Hz =SiO +H20 and (b) Si + SiO, = 2Si0 have beet1 studied at temperatures of 1425"to 1600°C ad 1310°to 1485°C respectively. The stattdard free energy changes for the tzrro reactions are given by the equatiotts Combination of the results for both equilibria leads to tiotz removes certain anomalies in existing high-terlzperature data for equilibria involving silica and silicon in iron. In many metallurgical processes and in many laboratory investigations silicon monoxide undoubtedly plays an important role. It is unfortunate therefore that wide differences exist between the results obtained by different investigators1-7 in their studies of such equilibria as In an attempt to put our knowledge of SiO on a surer basis, an exhaustive study has been made of equilibria [I] and [2] at temperatures ranging from 1300" to 1600°C. Reaction [I] was studied by measuring the amounts of silica which could be condensed from streams of Hz or Hz + HzO which had previously been brought into equilibrium with silica at temperatures ranging from 1425" to 1600°C. Reaction [2] was studied by measuring the material that could be condensed from streams of Hz or argon which had been brought into equilibrium with mixtures of silicon and silica at temperatures ranging from 1310" to 1485°C. EXPERIMENTAL Materials. The silicon was "superpure" grade and contained less than 0.1 pct impurities. The silica was prepared from pure mineral quartz; this was crushed and treated with concentrated hydrochloric acid to remove particles of iron, washed with water, and finally dried at 120°C. For the hydrogen + silica reaction, the silica was sized to —20+100 mesh. For the silicon + silica reaction, the two materials were ground to a fine powder in an agate mortar. The hydrogen and argon were commercial oxygen-free gases. The gas streams were controlled with capillary flow meters and the volumes were measured by wet gas meters. After passing through the meters, the gases were partially dried by silica gel. The hydrogen for the HZ + SiOz reaction was then passed through palladised asbestos at 300°C and dried with magnesium perchlorate. The efficiency of oxygen removal was checked throughout the experiments by passing the gas over an electrically heated strip of nichrome, used as an indicator as described by Rathman and de itt.' When mixtures of HZ + Hz0 were required, the partial pressures of water vapor (1.8 to 22 mm) were obtained by passing the hydrogen through oxalic acid dihydrateg' lo held at various controlled temperatures, O.l°C, by means of a water bath. The hydrogen for the Si + Si02 reaction was purified by passing it over a mixture of 3 parts of magnesium to 5 of lime heated to 600°."l1 u The argon for this reaction was passed through titanium powder (-3/16 in. + 100 mesh) heated to 900°C. The nitrogen used to prevent the reaction products escaping from the condenser (see later), was deoxidized by copper or iron at 600°C. All these gases were finally dried with magnesium perchlorate. Furnace, Temperature Contr01, and Measurement A molybdenum resistance furnace was used for both sets of experiments. The reactions were conducted inside a high-grade alumina tube, 36 in. long and 1 in. in diam as indicated in Fig. 1. With this arrangement an even temperature zone (2"C) 4 cm long was satisfactorily obtained. The temperatures were kept constant by means of a proportional controller actuated by a Pt-Pt 13 pct Rh thermocouple. This was placed between the two alumina tubes, so that the temperature at the junction was 1400" to 1450°C. Up to 1485"C, the temperatures were measured with Pt-Pt 13 pct Rh thermocouples. For higher temperatures an optical pyrometer was used, this being sighted (through the glass window 1 in Fig. 1) on the end of the alumina tube, that held the SiOz or Si +SiOz mixture, 10 in Fig. 1. The optical pyrometer was recalibrated whenever a change was made in any part of the apparatus situated in the hot zone. Successive readings with the optical pyrometer were reproducible to within 1"C. Equilibrium Apparatus and Procedure. Hydvogen and Silica Reaction. The apparatus is shown in Fig.

Jan 1, 1962

By Steve H. Carpenter, Henry E. Otto

The explosive welding of metals is dependent upon the production of a jetting action caused by the collapsing of one metal plate against another. Successful welds are generally accomplished if the yield strength of the metals is in the range of 10,000 to 90,000 psi and the sonic velocity of the metal is greater than the detonation velocity of the explosive if direct contact explosive is being used.' Should the detonation velocity exceed the velocity of sound in the metal it may still be possible to obtain the jetting action and a good weld. However, in most cases where a high detonation velocity is used complications arise because of reflected shock waves which tear the bond apart as fast as it is put together.' Explosive welding of lead presents several problems since its yield strength and sound velocity are very low. Various values have been published3-5 for the velocity of sound in lead ranging from 2000~ to 23004 m per sec. Most of the high-order explosives have detonation velocities on the order of 6000 to 8000 m per sec, which precludes their use. The dynamites have a lower detonation velocity of around 2800 m per sec which is still somewhat too high. Lower-order explosives such as ammonium nitrate (1070 m per sec) must be used to weld lead in the as-received condition if the explosives are used in direct contact. Rather than use low-order explo'sives it was decided to alter the sonic velocity of the lead. The sonic velocity is directly related to the modulus of the material according to the following expression: Fig 1—Interface of explosive weld of lead to steel. Lead is on top As-polished Magnification 75 times as well as the yield strength. Bolling et al. 6 show that the shear modulus of lead single crystals increases from about 0.72 X1011 dynes per sq cm at 300°K to about 0.98 X1011 dynes per sq cm at 0°K, an increase of approximately 3 5 pct. This gives an increase in the sonic velocity of around 700 m per sec. Hence, the sonic velocity of lead at cryogenic temperatures is approximately equivalent to the detonation velocity of the low-order dynamites. We have obtained high-quality lead to steel explosive welds using a 40 pct dynamite in direct contact with the lead. Prior to detonation the lead was chilled with liquid nitrogen (78°K) to increase the strength and sonic velocity. Welds were made while the lead was cold. Specimen sizes were 3 by 6 in. A preset angle of 5 deg with a 0.10-in. standoff at the base was the geometrical setup used. The amount of explosive used for optimum welding of an 1/8 -in. -thick lead sheet to a steel plate was found to be 7 g per sq in. A PETN sheet explosive line wave generator was used to insure a linear detonation front through the dynamite. A photomicrograph of a lead-steel weld is shown in Fig. 1. The typical wave effect that constitutes a good explosive weld is present. When tested in shear, the weld failed in the lead, indicating that the bond is stronger than the lead base metal. Higher-order explosives were also tried without success. We believe this indicates the importance of matching the detonation velocity and the sonic velocity for successful explosive welding. Note Added in Proof. High quality explosive welds of lead to steel have recently been obtained at ambient temperature using a low velocity (1000 M per sec) free running dynamite. The weld interface obtained is comparable to Fig. 1. 'S. H. Carpenter, R. H. Wittman, and R. J. Carlson: Proceedings of the First International Conference of the Center for High Energy Forming, Syracuse University Press, syracu.se, N. Y., in press. 'A. HI Holtzman and G. R. Cowan: Welding Risearch. Council Bull., No. 104, April, 1965. 'Metals Handbook, 8 ed., p. 1062, Metals Park, Ohlo. 'J. M. Walsh, M. H. Rice, R. G. McQueen, and F. L. Yarger: Phys. Rev., 1957, vol. 108, pp. 196-216; 'L. V. Al'tshuler, K. K. Krupnikov, B. N. Ledener, V. I. Zuchikhin,

Jan 1, 1968

By M. E. Wadswort, A. S. Peck

Infrared data disclose that phenacite reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. The absorption band characteristic of the antisymmetrical C = 0 oleate structure appears at a spectral wavelength of 1623 cm-'. Chemisorption also results in the displacement of OH- and silicate from the mineral surface. Infrared absorbance at 1623 cm-1 is correlated with float-ability at different pH for -60-mesh phenacite particles. Phenacite, Be2SiO4, is an ore mineral often associated with quartz, microcline, and chrysoberyl in pegmatites and mica schist. Experimental phenacite beneficiating processes have been confined principally to the flotation of low grade ores occur-ing in several mountain ranges of Utah and Nevada. The U.S. Bureau of Mines ' has recently reported on the separation of phenacite from ore deposits of Mount Wheeler, Nev. Infrared techniques were previously applied by the authors to characterize the role of sodium oleate and oleic acid in the flotation of several non-sulfide minerals.23 A parallel study was projected to the flotation of the orthosilicate mineral phenacite with oleic acid. Infrared spectra provided a 'molecular fingerprint' of the mineral surface and permitted identification of the reaction mechanisms. Infrared data were complemented with flotation and chemical tests. EXPERIMENTAL PROCEDURES The experimental procedures used in this investigation, for which data are presented in graphical or spectral form, are described in chronological test order. Phenacite crystals from Mt. Antero, Colo., were obtained from Ward's Co., Monterey, Calif. The crystals were fragmented in a porcelain mortar to -60 mesh and then pretreated with 0.5 molar HC1 for 15 min to remove iron. Then, the mineral particles were washed free of acid with distilled water and dried. Part of the dried material was ground to a fine powder with a Fisher Grinder using an agate mortar and pestle. Next, the powder was placed in a graduated cylinder and mixed with 500 ml of distilled water. The mineral in suspension was decanted from the settled fraction after 5 min, and the colloidal suspension was used for adsorption tests in which a high specific mineral surface area was required for adsorption and infrared analysis. Conditioning was performed in 50 ml glass centrifuge tubes for both infrared and flotation test determinations. Twenty ml of colloidal suspension was used for the infrared adsorption tests. One and a half g of deslimed -60-mesh HCl pretreated phenacite was added to 20 ml of distilled water for flotation conditioning tests. Six mg of oleic acid was used for each infrared adsorption test, and 0.2 mg of oleic acid was used for the flotation conditioning tests. HCl and NaOH were used for pH modification. The pulps were stirred at a speed of about 1500 rpm for 3 min. Then, the solids were separated out and either dried at 50°C or immediately transferred to a float cell. The pH of the residual liquid was determined with a Beckman Zeromatic pH meter. The flotation procedure is described as follows: 1) A 325-1111 glass micro-float cell was filled with distilled water. 2) Conditioned mineral was placed in the cell and the pulp was aerated through the glass fritted bottom at 7 psi pressure. 3) Floated mineral was skimmed from the cell with a glass slide until flotation ceased. (The end point was reached in all tests in less than 2 min.) 4) The flotation products were dried, weighed, and the recovery was calculated. Samples for infrared analysis were made into mulls using either oleic acid or series 13-21 Halocarbon oil obtained from Halocarbon Products Corp., Hacken-sack, N.J. The mulls were placed between two sodium chloride windows. A characteristic phenacite infrared band at 1868 cm-' was used as an internal standard for quantitative determinations in which absorbance at this position was quantified by the baseline-tangent method4 and related to absorbance at 1623 cm-'. The ratio obtained by dividing absorbance at 1623 cm-' by absorbance at 1868 cm-' was defined as an absorbance quotient for use in graphical presentation.

Jan 1, 1968

By R. F. Stewart, A. W. Hall

A method has been developed for continuously measuring the moisture content of coal. The method is based on the thermalization of fast neutrons by hydrogen in the coal. Neutrons from a small radio-isotope source penetrate the coal, are scattered by hydrogen, and measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. In a pilot-scale system, moisture was measured continuously within 0.2% in coal moving at rates up to 20 tph. The method is adaptable in industry for continuously measuring the moisture content of coal at high tonnage flow rates. Such an application would permit continuous recording of moisture in coal without sampling and facilitate quality control. An automatic and continuous method of measuring the moisture content of coal is needed by the coal industry. Automatic control of the coal quality would reduce the cost of coal preparation, improve the product, and thus indirectly increase the use of coal. Moisture in coal can be determined by several methods, but the time required to obtain samples and analyze them by existing methods makes it difficult, if not impossible, to control the quality of the product. Both producers and consumers need a method for continuous and instantaneous measurement of moisture content without sampling in order to regulate process equipment and keep the moisture content of coal within specifications. At the Morgantown, W. Va., Coal Research Center we are developing a nuclear method for continuous measurement of moisture in coal. This method is based on the thermalization of fast neutrons by hydrogen in the water and organic matter of coal. Neutrons from a small radioisotope source penetrate the coal, are scattered by hydrogen, and are measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. Design of a moisture meter based on neutron thermalization depends on many variables, any or all of which can affect the sensitivity of the meter. These factors include those related to the nuclear aspect; type and size of neutron flux and source, type of detecting device, and background count; and those related to the coal being tested: rank, particle size, and ash content. A survey was initiated to eliminate the relatively insignificant factors and to ascertain the magnitude of the major effects. Such information was necessary to fully evaluate the technique and to establish design criteria. Coal contains a relatively large amount of hydrogen in the organic coal substance and the water of hy-dration of the shaly material as well as in the moisture. To apply this concept of moisture measurement to coal requires that the organic substance in coal from any one seam of a particular mine be uniform in hydrogen content. The difference in total hydrogen content of wet and dry coal is relatively small, so that a moisture measurement based on this concept requires a measurement between two large numbers to a high degree of precision. Thus, it was necessary to develop a highly precise instrumentation system for continuous measurement and to obtain a physical arrangement permitting measurement of moving coal with a minimum effect from density variation. EXPERIMENT WITH TRAYS OF COAL Tests were conducted with metal trays containing SO to 100 lbs of coal to develop an instrument system of high precision. A scaling system with a maximum instrument error of 0.2% was used to test different types of thermal neutron detectors. The most suitable type of detector was a boron-10-lined proportional counter tube. While this type of detector showed satisfactory stability, extensive testing disclosed a long-term count reduction probably due to some type of deterioration in the detector. However, development of an electronic system using dual detectors eliminated this deterioration as a serious problem. (The second detector would be used to measure a reference drum of dry coal — the difference in count rate between the wet coal and dry reference coal being a direct measure of moisture content.) Table I, column 1, shows typical results with a 1-curie plutonium-beryllium neutron source and a thermal neutron detector beneath a tray of coal and illustrates the precision of measurement. Consecutive measurements (indicated in Table 1, columns 2-5) of thermal neutrons at various times and positions be-

Jan 1, 1968

By Antoni Kidybinski

Mechanical properties of the nether roof rocks play a substantial role in maintenance of mine openings. On longwall faces too low strength is a cause of rock- falls which bring about delays in face advance, and hazard to the miners, while too high strength may result in over hanging of roof rocks in gobs, sometimes over a large area, initiating dynamic periodical pressures. Hence, efforts have been undertaken to develop methods of caveability evaluation for proper selection of roof control system and of longwall-face supports. DESCRIPTIVE CLASSIFICATIONS One of the basic qualitative criteria for classification of roof types with different caveability is the criterion of geological structure. The 26-stages scale worked out for conditions of Donetz Coalfield. USSR, by E.T. Proyavkin et al.(l) may be an example of that type of classification. This scale is presented graphically in Fig. 1. The first types of roofs according to this scale are easily caving immediately after exposure of a small surface, while the last be- long to the strongest roofs which over-hang in waste and require artificial fracturing. Observations and measurements carried out also in Donetz mines lead W.T. Davidyanc (2) to following classification: Class I - weak and densely bedded rocks very easily caving after each advance of supports. The roof subsidence over a waste edge is: [ ] where: h is roof subsidence, m M is thickness of the seam being mined, m S is width of an opening, m Class II - medium caveability and small main roof movements [ ] Class III - hardly breakable rocks, thicker beds with higher strength: caving by large blocks. After exposure of larger roof surfaces the movements of the main roof strata may affect an opening. [ ] Class IV - very hardly breakable rocks - thick, monolithic sandstones: they cause considerable difficulties in working with caving. [ ] Class V - thin-bedded rocks featured by the capacity of a smooth subsidence without disintegration into loose blocks with keeping contact between the particular blocks in a bed. In this classification mining with full roof caving is recommended for class I-III and only exceptionally for class IV. In many coal fields, qualitative and quantitative observations of roof rocks behavior have been carried out: as a result relations and characteristics found in certain mines are given. As an example, Kizielov Coalfield data in the USSR given by B.S. Vinokur (3) may be mentioned. In working thin pitching seams man- less system of undercutting the seam by means of rope saw is used there. The author separated four classes of roofs and gave, for every class, the empirical relation between the extracted area and the time of roof stability. The size of the stable area of exposed roof for particular classes is as follows: 120 to 150 m2 (1291 to 1614 ft2 ), 170 to 200 m2 (1829 to 2152 ft2), 250 to 280 m2 (2690 to 3013 ft2 ) and 350 to 400 m2 (3766 to 4300 ft ). For Kuznetz coalfield in the USSR the following classification of roofs was developed at the WIMI Institute in Leningrad: Class I - completely unstable: impact strength in- dex of rock f = up to 1.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide, exposed after shearer's cut holds stable during the time not longer than 5 min. Class II - low stability: f = 1.5 to 2.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and up to 4.0 m (13 it) long, exposed after shearer's cut holds stable during 5 to 20 min. Class III - medium stability: f = 2.51 to 3.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide and 4.0 to 25 m (13 to 82 ft) long, exposed after shearer's cut holds stable from 20 min. to 2 hours. Class IV - stable: f = 3.51 to 4.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and 25 m (82 it) long exposed after shearer's cut is stable during the time longer than 2 hours. Class V - entirely stable: f = over 4.5

Jan 1, 1982

By T. P. Floridis, J. H. Young

The need for close control of the phosphorus content of steels has led to numerous investigations on the equilibria of the dephosphorization reactions. Winkler and chipman1 have established the general conditions for effective dephosphorization of steel. They are high slag basicity, high oxygen potential, and low temperature. Other investigators have made additional contributions to the understanding of the dephosphorization process. The current status of the understanding of the dephosphorization of steel is concisely presented by Bodsworth2 and by Ward. The investigation reported in this communication was undertaken with the purpose of establishing the effect of additions of barium oxide and calcium fluoride on the dephosphorizing capacity of slags. Esin and Gel'd4 proposed that barium oxide, being more basic than calcium oxide, should cause an increase in dephosphorizing capacity when added to steelmaking slags, or when used as a substitute for calcium oxide. Derge5 has also proposed that in the future conventional slags might be replaced by BaO-Al2O3 slags. There is, however, no experimental evidence confirming the effect of barium oxide on the dephosphorizing capacity of slags. The effect of calcium fluoride on the dephosphorization of steel is not clearly understood. It is generally recognized that additions of calcium fluoride are beneficial. It is not clear, however, whether calcium fluoride affects the equilibrium of the dephosphorization reaction, or whether it simply causes an increase in the fluidity of the slag and, consequently, faster approach to equilibrium. The experimental procedure consisted in equilibrating synthetic molten slags with liquid copper at 1550°C under a gas stream containing argon, hydrogen, and water vapor. In all experiments the argon to hydrogen ratio was approximately 4:1, and the hydrogen to water ratio was 5.42:l. Molybdenum crucibles were used as containers for the slag and metal. Under the above-described conditions of temperature and composition of atmosphere, there was no observable attack of the crucibles by the metal, slag, or atmosphere. Copper was used instead of iron, because iron attacks molybdenum. The equilibration was made in a tubular furnace consisting of a recrystallized alumina tube. The alumina tube was heated by electrical resistance. A Pt-40 pct Rh wire winding was used for most runs. A silicon carbide tubular resistor was also used for some runs. Temperatures were measured with a Pt-Pt-Rh (10 pct Rh) thermocouple and kept constant within ±5°C. Equilibrium was approached from both sides, i.e., by adding the phosphorus either as oxide in the slag or as a phosphorus-rich alloy of phosphorus and copper. The holding time at the equilibrium temperature was 6 hr. At the end of each run the crucibles were rapidly cooled and removed from the furnace. The slag and metal were separated and analyzed. The experimental results are shown in Table I. The phosphorus content of the slag is expressed both as percent phosphorus pentoxide and as percent phosphorus. The basicity ratio is computed by dividing the number of moles of basic oxides-oxides of barium, calcium, magnesium, and sodium—by the number of moles of acidic oxides- oxides of aluminum, phosphorus, and silicon. Calcium fluoride is not included in the computation of the basicity ratio; i.e., calcium fluoride is assumed to be neither basic nor acidic. The distribution ratio of phosphorus—percentage of phosphorus in the slag divided by the percentage of phosphorus in the metal- is plotted in Fig. 1 against the basicity ratio. The results indicate that slags containing barium oxide have greater dephosphorizing capacity than slags containing calcium oxide. The high dephosphorizing capacity of slags containing sodium oxide and the low dephosphorizing capacity of magnesia-containing slags which already have been reported in the literature2 are confirmed by the results of this investigation. It appears that calcium fluoride has a beneficial effect on the distribution of phosphorus between slag and metal in acid slags only. Although the obtained distribution ratios between the phosphorus contents of slag and copper are not directly applicable to the dephosphorization of steel, they are sufficient for evaluating the effect of slag additions on the dephosphorizing capacity of slags in general. An increase in the ratio of distribution of phosphorus between slag and metal indicates lowering

Jan 1, 1968

By W. A. Sheaffer

Electric furnace installation and tough-pitch copper-casting operation at Canadian Copper Refiners Ltd. are described. General layout, power supply and control, refractories, induction pour hearth, casting equipment, metal temperature control, and oxygen-content control are discussed. E LECTRIC furnace at Canadian Copper Refiners Ltd. was put into operation in August 1949. The installation was designed primarily to melt electrolytic copper cathodes and to produce vertically cast tough-pitch shapes. To meet emergencies during reverberatory furnace shut-downs, provision was made for casting horizontal tough-pitch wire bars. Due to the ease with which metal temperatures, melting rates, oxygen content, and casting hours can be altered to suit production demands, the electric furnace has met the requirements admirably. General Layout The plant has been described by H. S. McKnight' and by J. H. Schloen and E. M. Elkin.2 Since these papers were written, the electric furnace has been installed in a 140 ft extension of the original casting building. The extension, 264 ft in width, is divided into one 24 ft and four 60 ft bays, each a continuation of similar bays in the older building. Fig. l, a partial floor plan of the extension, shows the location of major equipment. Power Supply and Control Power for the electric furnace and its auxiliary equipment is delivered by Quebec Hydro over two 12 kv three-phase, 60 cycle pole lines. One line is in use, while the second serves as an emergency standby. Connections for the electric furnace from these lines, which also feed the refinery power house, are made to a substation on Canadian Copper Refiners Ltd. property. Connections between this substation and the furnace transformer room are in underground conduit. The are-furnace transformer, 550 v auxiliary-equipment transformer, and 12 kv switchgear are in the transformer room near the furnace. Stepdown from 12 kv to are-furnace voltages is done by a 7500 kva oil-immersed water-cooled three-phase 60 cycle transformer. This unusually high kva rating is available because the arc furnace and transformer were adapted from a steel-melting unit. Secondary voltages are available in 16 steps between 251 and 95 v (across phases). A four-position tap changer, operated from the furnace switchboard is connected to taps yielding 199, 164.5, 127, and 115 v, respectively. The transformer primary feeder is equipped with a General Electric Magne-Blast circuit breaker. The pour hearth, casting wheel, bosh conveyor, and other auxiliary equipment are fed by a 12 kv to 550 v, 750 kva three-phase 60 cycle transformer. Graphite electrodes, 14 in., with tapered nipples are held in the are-furnace electrode arms with steel wedges. The arms, fed from the transformer secondary busbars by flexible cable bundles, are actuated by winch cables. Direct-current motors operating the winches are supplied by a 250 v motor-generator set. Power input to the furnace is controlled from the furnace switchboard. The board has the usual combination of remote controls for the 12 kv breaker and transformer tap changer, meters, overload relays, automatic and manual electrode motion controls, switchgear, etc. When power is on the furnace, automatic electrode feed is used; the power draw on a given voltage tap then is governed by current-limiting rheostats. The rheostats work through a Westinghouse bal-lanced-beam control circuit which, in turn, operates reversing contactors in the winch motor circuits. Arc Furnace The arc furnace is a standard-type NT Pittsburgh 'Lectromelt with inside shell diameter 12 ft 3¾ in. By hydraulic-lift cylinders, the furnace can be tilted forward to 39 ½ ° and backward to 5" from horizontal. A roof-swing cylinder is also installed but not used. Fig. 2 shows refractory-lining details. With the lining as shown, operating life between repairs is 6 to 9 months of two-shift casting operation. Charge slot, skim door, and roof refractories then are replaced completely, and any necessary repairs made to side walls. Bottom life is longer and the original under courses are still in service, while the top course was replaced in October 1951. The launder is lined with high chrome-magnesite trough brick backed by fireclay and insulating brick. The trough is covered with fireclay brick and asbestos sheet. At intervals, openings 12x6 in. are left in the permanent covering. These are covered with

Jan 1, 1956

By R. T. Hukki, P. Voutilainen

This paper describes a new apparatus for continuous wet fine-screening. Its preferred size range seems to be from 0.1 to 1 mm. The supercritical trommel screen is a short cylindrical trommel of wedge-bar type construction operated at a speed greater than the calculated theoretical critical speed and at a speed lower than the speed at which particles introduced into it will centrifuge. The paper describes results obtained with the prototype supercritical trommel screen in pilot plant scale. The results point to a high capacity and simultaneously to a high sharpness of screening. Finally, an analysis is presented of the forces acting in screening on a supercritical trommel screen. In the era of high speed, high capacity processing of raw materials the conventional slowly rotating trommel screen is often considered a relic from the times passed. A typical trommel screen is the cylindrical trommel rotated about a horizontal or slanting axis at a relatively low speed. Its screening characteristics are well known. Trommel screens of various types of construction, methods of operation, performances and other characteristics have been described in detail by Taggart.1 The theoretical critical speed of a trommel screen is defined by the same well known equation as that applied for grinding mills: where ncritical = the numerical value of the theoretical critical speed in rpm, D 1 = the inside diameter of the trommel in feet, and D2 = the inside diameter of the trommel in meters. ncritical corresponds also to the centrifuging speed provided that the coefficient of friction f between the trommel surface and the outer layer of the charge is = 1.0. In a general case: From Eq. 2 it is seen that in all cases where f < 1.0 the centrifuging speed of the trommel is greater than the theoretical critical speed. The supercritical trommel screen concerns screening operations within that speed range which is between the theoretical critical speed defined by Eq. 1 and the centrifuging speed defined by Eq. 2, under conditions such that the coefficient of friction f<1.0. It is reported by Taggartl that the optimum speed of a conventional cylindrical trommel screen 36 in. in diam was experimentally found to be about 16 rpm. From Eq. 1, the critical speed of this trommel is 44.2 tpm. The indicated optimum speed corresponds to (16/44.2) x 100% = 36.2% of the theoretical critical speed. The optimum speed range based on information available seems to vary from 33% up to 45% of the theoretical critical value. The trommel screen operated at a supercritical speed: operates at a speed greater than the calculated theoretical critical speed; operates at a speed lower than the speed at which the charge introduced into it will centrifuge; operates within the supercritical speed range in such a way that the coarse fraction of the charge must slide in respect to the inside surface of the trommel; the outer layer of the said fraction next to the screen tends to proceed in the same direction as any selected point on the trommel surface, but now at a lower speed, and indeed at a subcritical speed; allows to a certain degree adjustment of the maximum determining particle size x of the fine product simply by a variation of the speed of the trommel within the supercritical speed range. With increasing trommel speed, finer and finer material only will get the opportunity to find its way into the fine product while the screen opening remains constant. In conventional practice, the low speed trommel is generally used for sizing of coarse and medium coarse material, but seldom for fine screening. The characteristic feature of the product passed through the conventional trommel is that the determining size x of the biggest particle is barely smaller than the nominal size of screen opening. The supercritical trommel screen, on the other hand, is best suited for sizing of relatively fine material. Furthermore, the characteristic determining size x of the biggest particle in the fine product can be substantially smaller than the nominal width of the screen opening or slot. In the trommel screen best suited for the applications

Jan 1, 1965

By M. D. Hassialis, C. G. Myer

THE nature of a collector-coated mineral surface has been the subject of some experimentation and much speculation. Various aspects of the problem have been isolated and studied; it is probable, however, that there exist aspects as yet unrecognized, which are needed for a complete description of the system. The recognized elements of the problem are: 1—The nature of the chemical units comprising the film and the nature of the forces holding these chemical units to the mineral surface; 2—The orientation of the chemical units at the surface; and 3—The disposition of the collector units at the mineral surface. This report touches upon all three aspects of the broad problem; it deals, however, with a new and heretofore unrecognized element—the mobility of the collector units in the two dimensions of the solid-liquid interface. Regardless of the viewpoint adopted as to whether the chemical units comprising the collector film are collector ions or molecules, held either by chemical or physical forces, the writers on flotation theory are in apparent agreement as to the orientation of the chemical units at the mineral surface. Wark and Cox&apos; showed that the contact angle at a stable collector-coated surface in a constant chemical environment is independent of the nature of the mineral and of any resurfacing agent; it depends solely upon the collector used. They showed further that the value of the contact angle increases with the number of carbon atoms in a homologous series of compounds. Taggart, Taylor, and Knoll2 postulated that the collector ion is oriented with the chemically reactive, polar end toward the mineral surface and the non-polar, hydrocarbon-like end toward the liquid phase. In support thereof they cited the abstraction of p-p1 dihydroxydiphenylthiourea and of glycol xanthate8 by galena without a concomitant increase in the contact angle above that of clean galena. It was argued that in these cases the water-repellent layer which normally would be presented to the liquid phase owing to the orientation of the collector ions is overlain by a layer of water-avid groups, the hydroxyl groups. Implicit is the analogous orientation exhibited by a monomolecular layer of an insoluble substance at an air-water interface. It should be pointed out that these facts also are consistent with the concept that the collector units be flat on the surface of the mineral and that the response of the surface to an air bubble is determined by the ratio of the area covered by water-avid groups to the area covered by water-repellent groups; the areas being weighted according to the relative watef-avidity or water-repellency of the groups involved. The disposition of the chemical units of the collector film at the mineral surface has not received the attention it merits. Taggart4 concluded from the observed stoichiometry of the ions entering and leaving a surface that the stoichiometry is obeyed in detail at the surface of the mineral. Thus, in the case of xanthate-coated galena, pairs of xanthate ions are attached to surface lead ions. In the case of chemisorption, Gaudin and Preller postulated an agreement between the atoms or ions of the substratum (the mineral surface) with those of the superstratum (collector film); in the case of the physical adsorption their position is not clear. In one place they state "the first type (physical adsorption) does not require any agreement between the atoms or ions of the substratum with that of the superstratum" and in another place that "It seems, in fact, as though some slight influence of the substratum is formed even in physical adsorption." The present work shows that in some cases of chemisorption the chemical units of the collector film are in constant surface-bound motion and may not be assigned to any site of the surface, hence there is no permanent association between the chemical units of the film and the atoms or ions of the solid. The physical property of the collector film that is of paramount importance is its surface energy. Although this property is not susceptible to direct experimental determination, the related contact angle is. Much of the knowledge of the properties of a collector film derives (by deductive and inductive reasoning) from the behavior of an air bubble thereat

Jan 1, 1952

By R. J. Stoehr, F. Howell

Since the ore mined in the Grants-Ambrosia Lake uranium area is taken from a water-saturated sandstone formation, part of the milling operation includes a drying process. The authors discuss the merits and disadvantages of two methods: natural drying and mechanical gas-fired drying; operating and cost data are included. In the Grants-Ambrosia Lake uranium area, approximately 7000 tons of ore are mined each day from a water-saturated sandstone formation. This ore is sampled and treated at four separate milling operations. Prior to the design and initial construction of the milling facilities, very little was known as to the physical properties of the ore which would be handled in the sampling and crushing facilities at the mills. All four mills initially were constructed without ore-drying facilities. As mining proceeded, it was determined that, even after drying the ore in place by use of drainage development underground, the moisture content of the ore as hoisted averaged approximately 18 pct. Actually, some of the mines produced ores which resembled cream-of-wheat in character and had a moisture content in excess of 24 pct. Each of the four mills had a differently designed sampling and crushing plant; therefore, the moisture content of the ores had varying adverse effects upon the operation of the plants. It was determined after some experience that most of the sampling and crushing facilities could not economically handle ore if the moisture content was greater than 10 pct—one operator considers 12 pct moisture as a maximum. In all of the plants, moisture content over 8 pct increases costs to some extent. In addition to the added sampling and crushing costs, some of the mills were located 15 to 20 miles from the mines and the high moisture content of the ores increased the haulage costs from the mine to the mill. It was generally conceded that it was necessary to employ some method to reduce the moisture content of the ore prior to sampling. Several methods were considered: 1) natural drying at the mine site, 2) mechanical gas-fired drying at the mill site, 3) mechanical gas-fired drying at the mine site, 4) radiant heating on concrete clabs, and 5) infrared shed drying. After preliminary investigation all possibilities but natural drying and mechanical gas-fired drying at the mill site were eliminated. NATURAL DRYING A cooperative feasibility study was conducted on the natural drying method. This study indicated the following: 1) During summer months May through September, ore piled 4-ft deep would dry from +20 to +10 pct HzO in 30 days with no mechanical turning. 2) In the first four days after piling a reduction of 5 to 7 pct total moisture content was accomplished by drainage and absorption of the water into the underlying ground on which the ore was piled, providing the ground surface absorption rates approached 10 gal per sq ft per day. After the first four days the decrease of moisture caused by drainage was practically nonexistent. 3) In the summer months drying by evaporation amounted to approximately 0.1 pct decrease in total moisture per day and mechanical turning of the ore could increase this as much as three times. 4) Climatic conditions of the area indicated that: a) Air temperatures averaged 64&apos; May, June, July, August, September; 41" October, November, December, March, April; 31" January, February. b) Average rain fall was 10 in. with 40 pct of this occurring during July and August. c) Only on very rare occasions were there over five consecutive days with below freezing temperatures. d) The annual evaporation rate was approximately 75 in. On the basis of this study, two of the mill operations decided to attempt to meet the moisture specifications by natural drying supplemented by mechanical turning. The other two operations decided upon rotary gas-fired drying at the mill site. The natural drying method has been quite successful in practice. The ore running approximately 18 pct moisture is trucked from the head frame and piled in rows about 6 ft wide, 3 1/2 ft deep, 5 feet apart during the months of May through September. In approximately 30 days this ore will

Jan 1, 1961

By E. Wainer, K. D. Burnham

A wet beneficiation technique for producing wollas-tonite from its ore in high yield and purity has been evaluated in a pilot plant operation at the rate of 75 tons per month. Finely crushed, unsized wollastonite ore mixed with water is passed through a high in tensity oscillating wet magnetic separator of unique design and in a single pass over 90% of the wolla-stonite exhibiting a crystal purity of 99.8% is obtained irrespective of size of feed fraction. Thereafter, the material is processed by closed cycle standard wet milling and classification techniques to yield a 1µ size product, though any mesh size up to and including 50 mesh may be obtained, if desired. Costs appear to be significantly lower than those available from dry processed techniques. Wollas tonite made by this unusual wet process appears to have potential utility in the following fields: ceramics, paints, plastics, paper, organic finishes, reinforcement of portland cement items, controlled porosity refractory ceramic foams, cinder and concrete block paint, and the like. The 1µ and certain chemically processed varieties of wollastonite may have unusual utility in the paper industry both as a filler and as a coating material and in the organic finish industry. Extensive deposits of wollastonite ore equivalent to an average tenor of 50% to 60% of this latter mineral in easily separable form exists in and around Essex County in northern New York State in reserves of the order of several tens of millions of tons. While important portions of these deposits are susceptible to open pit mining techniques, one operation near Wills-boro, N.Y., involves tunnel mining and dry milling and beneficiation techniques. This mill and tunnel mine is presently being operated by The Cabot Corp. and a variety of particle sizes are now sold into markets in the ceramic, paint, plastic finish, floor tile and in similar fields in substantial tonnages on a repetitive basis. Serious investigation and study over the past several years has indicated that, outside of the obvious economies of open pit techniques for mining purposes, wet beneficiation and milling procedures applied to the ore not only represent a potential for greater economies in the production of a superfine finished product but yields products of improved properties exhibiting increased market potential which may not be available from the dry ground product. The Lewis and Deerhead deposits, controlled by the Adirondack Development Corp., appear to be identical to the Wilisboro deposit. Utilizing ore taken from the Lewis and Deerhead deposits, a pilot plant process for the wet beneficiation, milling and classifying of wollastonite ore has been operated for several months. After scalping a marketable garnet product from a minus 16 mesh dry crushed feed on a high intensity roll magnet the balance of the material is then roll crushed in a closed cycle until it will pass a 50 mesh screen. The product constitutes the feed of the wet magnetic separator. The heart of the new beneficiation process is a cyclically operated wet magnetic separator which exhibits the unique feature that unsized feed is easily handled. Product yields of higher purity are equal to that obtained with dry magnetic separations which use closely sized dry ore and multiple passes, but only produce wollastonite of about 98% mineral purity as determined by sink float techniques. It was anticipated that the wet processing through the grinding, milling and classification stage would yield a low cost 1µ ground product which should make available greatly increased applications for the mineral beyond those presently enjoyed. The improved purity was also expected to provide coarser sizes which might be utilized as a raw material for chemical modification which again would expand the uses of wollastonite. The evidence thus far collected appears to indicate that this premise may be expected to be fulfilled. There are on the surface of wollastonite particle sites at which cheinical reactions may occur1. It is believed that wet ground material provides a better base which will allow wollastonite a deeper entree into the field of chemical raw materials. Wet ground at 20µ and finer permits with certainty a number of chemical reactions, some of which are mentioned later in this article. While well crystallized wollastonite makes up the majority of the ore, the balance consists mainly of very weakly magnetic diopside of the hedenbergite-

Jan 1, 1965

By M. F. Williams, L. G. Hendrickson

IN classification of pulps bearing magnetized ferromagnetic particles, depolarizing is of great importance. If size separation is to be effective, particles must be individual rather than in floes. Depolarizing is also practiced in heavy medium separations in which ferrosilicon or magnetite is the medium. When particles of ferromagnetic material have been removed from a magnetic field, residual magnetism causes agglomeration. The term depolarizing refers to the operation of reducing or eliminating this residual magnetism and may thus be considered magnetic deflocculation. The terms demagnetizing and randomizing are also used. At the Research Laboratory of Oliver Iron Mining Div. in Duluth a method was developed for measuring depolarization of the pulp of ferromagnetic material. Experiments were made with Mesabi taconite,&apos; a natural magnetite of low coercive force. Ferromagnetic materials of higher coercive force, such as lodestone or the artificial magnetite produced by reduction roasting of hematite, present a more difficult problem, which was not within the scope of this investigation. It is possible, however, that some of the techniques evolved for measuring and calculating electrical characteristics of alternating current coils would be of use in depolarizing high coercive force material, particularly in conjunction with high-frequency alternating current, as proposed by Hartig and others.&apos;," Properties of Ferromagnetic Materials:&apos;7 Experimental work, described below, has shown that if a sample in the magnetized state is heated above the Curie point and cooled, much of the preferred orientation is destroyed and the sample is substantially depolarized. It has been thought that when the sample cools below the Curie point the domains cancel each other, leaving a zero net moment. However, such particles still exhibit a tendency to cohere, and undoubtedly this is caused by the forces of residual magnetism. -AS measured by the percent depolarization, this tendency is reproducible for any sample upon repeated heating above the Curie point and subsequent cooling and is independent of the initial state of magnetization. It is postulated, therefore, that as the material is cooled below the Curie point the domains in any particle do not completely cancel each other, but rather are preferentially oriented to some extent. Mechanism of Depolarizing with Alternating Current Magnetic Fields: It is believed that when ferromagnetic material is passed through an alternating magnetic field, depolarizing occurs in the decaying portion of the field. As the particles pass through the portion of highest intensity they become magne- tized. If the particles are not free to move, the polarities of the particles will be reversed (by a mechanism similar to that described above for magnetism) at a frequency equal to that of the applied field. As the material moves through the decaying field, intensity levels become such that a domain does not completely reverse, but stops on an axis of easy magnetization. By the time the material reaches the point of zero field intensity, a state of fairly random orientation of domains is achieved. If conditions are such as to give a completely random orientation, the particle will have little or no external magnetic field, and a pulp of such particles will be depolarized. Previous Work In 1918 E. W. Davis was granted a patent for demagnetization of magnetite pulps.&apos; His method consisted of passing the pulp through a tapered coil, activated by alternating current of normal frequency (60 cycle). This method, with minor modifications, has been used almost universally in all pilot plants and commercial installations in which depolarization of low coercive force materials has been required. Hartig, Onstad and Foot2,3 avd made a detailed study of the factors involved in depolarizing both low (below 100 oersteds) and high (above 100 oersteds) coercive force material. They developed a method for evaluating the relative degree of depolarization of any pulp based on the settling characteristics of the pulp. Their standard of comparison was a sample heated to above the Curie point and cooled in a zero field, all in a neutral atmosphere.* For low coercive force material they found treatment.Thisprocedure is subsequently called, in this report,theCurie that results equivalent to Curie treatment could be

Jan 1, 1957

By J. T. Norton, Pekka Rautala

The phases and equilibria in the W-Co-C system have been studied by X-ray diffraction methods, metallographic technique, and thermal analysis. In addition to the 7 phase, two double carbides, called 8 and have been revealed. The compositions correspond to CO3 W6C2 and Co3-W10C4. The reactions leading to these phases have been explained and tentative diagrams of stable and metastable equilibria proposed. The basic reactions in sintering cobalt cemented tungsten carbides are discussed. THE W-Co-C system is of fundamental importance in practical carbide manufacturing as well as for the understanding of the sintering mechanism. Surprisingly little is known about this system, for the probable reason that all the important alloys are of two-phase structure and that the diagram Co-WC has been treated as a quasi-binary. This obviously is incorrect, because WC decomposes before melting. One ternary phase, 7, of composition Co3W3C has long been known. It was first studied by Adelskold, Sundelin, and Westgren,1 although the isomorphous iron-tungsten carbide was known earlier. There have been in the literature several reports of two 7 phases.&apos; " Also the 7 phase has been considered unstable by Takeda4 and Westgren.1 The Co-WC diagram has been studied by Wyman and Kelley5 and a quasi-binary diagram has been published by Sandford and Trent.2 Takeda has published a tentative Co-W-C diagram, considering both metastable and stable equilibria. However, the lines of two-fold saturation are shown only partially and it seems impossible to complete the diagram without violating the phase theory. Therefore it seemed desirable to examine the system in more detail. Experimental Procedure The alloys used in the present investigation were made of powders of tungsten, tungsten monocarbide, cobalt, and carbon and were of the grade used in manufacture of commercial cemented carbides. The powders were ground and mixed in small stainless steel ball mills, using balls of the same material. Benzene was used as a dispersing agent. The mixing period was 1 hr, since this was shown to give suffi- ciently good mixing of the powders without too great a contamination from the mill. After ball milling, the specimens were pressed in cylindrical or rectangular dies. No paraffin or other lubricant was used and the small compacts had sufficient green strength to be handled without difficulty. Several sintering furnaces were employed. The most satisfactory arrangement was a vacuum furnace based on the Arsem principle which employed a graphite helix as the resistance heating element. Specimens were placed on graphite stands and there was generally a slight carburization or decarburiza-tion of the specimen surface, depending on the carbon content of the alloy. The evaporation of the cobalt at a sintering temperature of 1400°C was not significant, but became severe at 1500°C and higher. The sintering time was 1 hr at 2000°C and 2 to 4 hr at lower temperatures. It was not possible to quench the specimens, but the cooling rates were rather fast, greater than 300°C in the first minute. In the system under investigation, the reactions are sluggish, and it is believed that the high temperature structures are satisfactorily retained. The principal method of investigating the sintered specimens was X-ray diffraction by the Norelco recording spectrometer. Approximate determinations of the phase boundaries were made by the disappearing phase method. Ternary Phases To study the phase formation in W-Co-C system, a series of specimens was sintered at 1400°C. In this experiment two ternary phases, called here ? and k were formed in addition to the well-known 7 phase. The 7 phase, which has been completely described by Westgren: showed a range of homogeneity from 7 to 20 pct C and from 38 to 48 pct Co. At 1400°C the 7 phase was found to be in equilibrium with monotungsten carbide, 8, tungsten, 8, #?, and liquid. The boundaries toward #? and liquid were difficult to determine and appeared to be very temperature sensitive. The other boundaries are believed to be well fixed. The homogeneity range of 7, as measured in this work, is considerably smaller than the one

Jan 1, 1953

By T. C. Atchison, W. I. Duvall

Over the past ten years a series of investigations have been conducted to determine some of the pnysical processes involved in breaking rock with confined concentrated charges. Detailed discussions of many of these investigations have been published elsewhere.1-6 Laboratory experiments made by other investigators using Hopkinson pressure-bar techniques have shown that solid materials are fractured in tension by the reflection of an incident compressive stress pulse at a free surface.7-12 In these tests a small charge of explosive is placed in contact with one end of a bar. Detonation produces some plastic flow and crushing of the bar near the charge and generates a compressive stress pulse that travels along the length of the bar. At the free end of the bar the compressive stress pulse is reflected back into the bar as a tensile stress pulse. If the tensile strength of the bar is exceeded during this reflection process, a tensile fracture normal to the length of the bar is produced, and the broken end of the bar moves forward with a constant velocity equal to the average particle velocity trapped in the broken fragment. The new surface formed by the fracture becomes the new free end of the bar that reflects the remaining portion of the incident compressive stress pulse. This process is repeated any number of times until all of the incident stress pulse is reflected. Hino has demonstrated this kind of breakage for three rock types—marble, granite, and sandstone." He has defined a blastibility coefficient, B, as the ratio of compressive strength, C, to tensile strength, T, thus: C The quantity B is the maximum number of slabs that can be produced by reflection breakage. Normally fewer slabs are produced because of loss of energy as the stress pulse travels through the rock. Fig. 1 illustrates reflection-type fracture for a triangular compressive stress pulse. The number of slabs produced by the reflection breakage process is the first whole number less than the ratio of the peak stress of the incident pulse to the tensile breaking stress of the solid. Thus the number of slabs is given by the thickness of each slab is given by and the total length of rock broken is given by N = number of slabs S - peak stress in incident pulse T = tensile strength of the rock F = fall length of incident stress pulse h = thickness of each slab D = total length of rock broken During the reflection process the particle velocity at the free surface is twice the particle velocity in the incident stress pulse. Thus the velocity with which the broken fragments move forward is given by where v, = velocity of broken fragment, and v = average particle velocity contained in that portion of the incident pulse trapped in the broken fragment. Results of these laboratory experiments cannot be applied directly to rock blasting where the explosive charge is placed in a drillhole. In laboratory tests the charge is unconfined and in contact with the rock in only one direction. In a drillhole additional confinement is offered by the rock surrounding the charge and by the stemming placed above it. This additional confinement may be enough to allow the explosive gases to do additional work on the rock during their expansion. Other writers have discussed possible effects of gas expansion&apos;on rock breakage.13-10 However, very few experimental data are available to determine to what extent expansion of the gases is responsible for rock fragmentation. The USBM has studied the physical processes involved in breaking rock with confined concentrated charges by using simple crater tests breaking to one free surface. Crater tests have been performed in four rock types: granite, sandstone, marlstone, and chalk. Table I gives some physical properties of these rocks. Fig. 2 shows plan and section drawings of two typical crater tests and illustrates some of the test variables measured. For these tests the charge was placed at the bottom of the drillhole and primed with an electric cap. The hole was stemmed to the collar with sand and the charge detonated. Size and shape of the crater were measured after it was cleared of broken rock. As a given charge size was buried deeper in a drillhole, the crater depth usually was equal to or

Jan 1, 1960

By Frank Doxey

AT Dominion Steel & Coal Corp. it has long been recognized that continued mechanization of mine operations is necessary in the Pictou, Cumberland, and Sidney coal fields of Nova Scotia. The varied physical conditions in these fields call for special consideration of individual cases before planning is finalized. Because standard equipment cannot be procured which would operate successfully, many experiments have been necessary over the years to keep pace with the progress made in other countries. There are two mines, producing 2000 tpd, located in the Pictou coal field. The field is badly distorted and crossed by many faults. Seams are highly inclined and irregular and vary in thickness from 5 to 40 ft. Entries are difficult to maintain because of squeezing of the coal. ribs and movement of the roof and pavement. Output from the three operating mines in the Cumberland field is 3000 tpd. The field is highly inclined, inclination varying from 12° to 32°. Overlying beds consist of shales and massive sandstone lenses of extreme toughness and are responsible for bumps when the stresses are relieved by extraction. At greatest depth these are among the deepest coal workings in the world. Depth of cover ranges from 2300 to 4000 ft. This prohibits room-and-pillar working and necessitates longwall operation. Working of contiguous seams concurrently to maintain output increases the already difficult conditions. The Sydney field, with a frontage of about 30 miles, is the most important of the Nova Scotia coal fields. With the exception of one small area it is now wholly submarine. Output is approximately 21,000 tpd. Seams are 21/2 to 8 ft thick, and cover in the areas varies from 600 to 2300 ft, with an average of 1500 ft from sea bottom to the top of the seam. The seams dip in a seaward direction, pitches ranging from 6" to 4.0". The shoreline is the last place of entry to the seams and distance from the bank to the working faces is generally over 3½ miles, in some cases as much as 6½ miles. Ventilation is a problem and requires the construction of large permanent airways. Getting and Loading Coal: In 1925, in view of heavy pressures exerted by thickness of cover overlying the seams, roadways and pillars of the room-and-pillar system being worked began to break up and coal was lost. It was decided that a change in the method of extraction in areas with heavy cover was necessary, and experiments were made with many short walls and longwalls varying between 90 and 250 ft. Trial and error proved that the best operating length was between 400 and 500 ft, delivering all coal to the dip, with roadways to the face following a level course. The change-over was gradual, and the technique of roof control developed with the system, so that falls to the face are now very infrequent. An advantage of longwall mining is that it yields 95 pct extraction, especially important in coal seams of high quality or in seams where faults or disturbances restrict the workable areas. This percentage of extraction is based on the fact that the longwall advancing system takes development faces where pitch permits instead of driving headings and leaving roadway pillars. This system yields high tonnage during development and limits loss in extraction to duff left during operations. Accompanying disadvantages, on the other hand, are the heavy construction cost of main roadways and the necessity of driving all new flank face roadways through the gob. If the main roadways are driven through the solid, and large enough pillars are left on each side for protection against flank face weights, then the width of solid coal is approximately 1700 ft. This represents 10.6 pct of the coal available, or 89.4 pct extraction of the whole. These pillars, however, are of such size that they provide a useful pillar drawing area as a final operation of the mine. It may be that although the seam cannot be generally mined by the room-and-pillar method, it can be adapted to

Jan 1, 1955