Search Documents

By D. Kuhlmann-Wilsdorf

A new theory of work hardening is developed which rests on only a few simple principles and is applicable to a wide variety of materials and dislocation structures. It explains, qualitatively, the general characteristics of the three-stage shear stress-shear strain curve of fcc metals, as well as the most important features connected with easy glide. The value of, the work-hardening coefficient in stage 11, is derived quantitatively, from first principles, and is shown to be insensitive to many changes in detailed dislocation behavior. The low rate at which energy is stored during mechanical working in stage 11, the dependence of slip line length on stress, and the so-called Cottrell-Stokes law are explained. Although the theory is primarily developed for fcc metals and alloys, it is largely applicable also to some other materiuls, and in particular apparently to poly crystalline simple steels in theh linear range of hardening. FOR pure fcc metals and alloys, after many different pretreatments and under a great variety of testing conditions, the well-known three-stage work-hardening curve is commonly observed. Moreover, the work-hardening coefficient in stage 11, 011, bears an almost constant relationship to G, the modulus of rigidity, such that K = G/Brr" = 300, within a factor of about 2 either way. The very fact that the three-stage curve and the value of K are so very persistent, can hardly be understood except on the assumption that some quite simple phenomena are responsible. In this light all available theories of work hardening must be judged unsatisfactory: Each of them is based on some quite specific dislocation model, while it is known that metals with similar values of K may have widely different dislocation structures, for example, dislocation tangles in the case of pure fcc metals, and piled-up groups of dislocations in a-brasstype alloys. Thus, while a particular theory might conceivably represent a special case with a reasonable degree of accuracy, it cannot possibly have illuminated the underlying principle. Another severe criticism applying to the presently most widely discussed theories is that they employ empirical or even quite unexplained parameters in order to arrive at a numerical value of K. This indicates that some vital aspect of the work-hardening process has remained unexplained. In the present paper, a new theory of work-hardening is developed which does not suffer from the above shortcomings. It is derived from first principles, and is founded on the realization that the underlying causes for the three-stage work-harden- ing curve and for the persistence of the numerical value of O,, must be few and simple. As a first step it is shown herein that the experimental oklservations on "easy glide" can be explained on the assumption that in this stage dislocations multiply, beginning in a number of restricted area:;, and from there penetrate into crystal regions still substantially free of glide dislocations until a quasi-uniform dislocation distribution has been established. During "easy glide", the resistance to the movement of the foremost dislocations, advancing into still largely a dislocation-free regions, is believed to control the flow stress. This resistance is determined by various factors, among them the reaction of the dislocations against bowing-out into loops, which is due to their line tension. Without such bowing-out no dislocation multiplication would occur, but the corresponding contribution to the flow stress stays practically constant all through stage I. According to the present theory, stage TI begins as soon as there are no more areas left into which newly formed dislocations have not yet penetrated, i.e., as soon :is a quasi-uniform dislocation density has been attaned. Regardless of how, in detail, the dislocations should happen to be arranged at the end of "easy glide", whether in pileups or tangles, on one glide system or on several, the stress necessary to overcome the line tension of the segments must now increase, because the dislocation density increiises while the average free dislocation length decreases. It is argued that all other contributions to the flow stress stay at about the same level as in stage I, and that the said increase in the stress necessary to bow out dislocation segments into loops is responsible for the major part of work hardening in stage 11. Stage TII of the stress-strain curve is explained by largely follouing the ideas of Seeger and his co-workers; however, it is pointed out that the start of stage m may on occasion indicate the onset of "conservative climb" instead of cross slip. Indirect evidence indicates that linear work hardening persists even under the profuse action of cross slip, but at a lower rate. Only when, in addition to cross slip, climb operates extensively, does the work-hardening rat,. drop sharply, ultimately down to zero. BRIEF SURVEY OF EXPERIMENTAL EVIDENCE The stress-strain curve of crystals of many different substances are qualitatively similar. No significant permanent plastic deformation takes place below the so-called "critical resolved shear stress". As the applied stress is raised beyond this level. yielding occurs with little or no work hardening and

Jan 1, 1962

By S. K. Tarby, W. O. Philbrook

The rate of FeO and MnO reduction from silicate and aluminate slags by carbon-saturated iron is dependent on both slag composition and temperature. Owing to variable stirring rules during- the course of reaction, the reduction processes occur in two stages in stationary graphite crucibles. In the first stage the slirring caused by CO evolution results in forced convection conditions in the slag. As the boiling action subsides during reduction, the flow conditions within the system become those defined by natural convection. Analysis of the data by an unsteady-state penetration model indicates that the rate of reduction is controlled by the rate of cocur-rent flow of' cations and anions from the bulk slag to the interface during both stages of reduction. The hearth reactions of the blast furnace have been extensively investigated from the viewpoint of equilibrium by deductions from controlled laboratory experiments. However, the literature contains relatively few studies that have been directed toward the area of slag-metal reaction kinetics, and the majority of these have been concerned with the rate and mechanism of sulfur transfer between iron and slag. More recently, attention has turned to the kinetic factors in the reduction of oxides from liquid slags. One of the first investigations in this field was conducted by Dancy1 on the reduction of pure liquid FeO and pure liquid Fe3O4 by carbon-saturated iron. The integrated form of the rate equation indicated that the reduction of FeO was of the first order up to 80 pct reduction. Over the initial 30 pct of reduction, the magnetite reaction was also interpreted as a first-order process. The rates of reaction were extremely rapid as indicated by a 30 pct reduction of the liquid magnetite in a time interval of about 1 to 2 sec. Phil-brook and irkbbride' studied the reduction of FeO from a lime-alumina-silica slag by carbon-saturated iron and solid graphite in stationary crucible assemblies. With the use of the differential form of the rate equation, the rate of the reduction reaction was found to be proportional to the second power of the concentration of the reactant FeO for both the slag-metal and slag-graphite reactions. These authors presented a number of comments in an effort to explain the difference between the molecularity of the above reaction and the observed second-order relation. One such argument, recently extended by Wagner,3 was that the rate-limiting step may well be one of transport control. A complete discussion of the proposed mass-transport control mechanism of this reduction reaction will be presented in a later section of this paper. Kinetic studies of the reduction of other oxide species, namely chromous oxide, titania, and silica, have also been reported. McCoy and philbrook4 used rotating crucible assemblies to investigate chromium reduction from Ca0-SiO2-A12O3 slags. First-order kinetic law was obeyed for the slag-metal reduction reaction as determined by the integration method of data analysis. Due to scatter of the data, any dependence of the rate constant on temperature or slag composition was obscured. Concentration-time data for the reduction of titania from blast-furnace type slags under reducing conditions were obtained by Delve, Meyer, and Lander.' The data were too few, however, for a formal kinetic interpretation. Kinetic data for the very slow reaction of silica reduction have been observed by McCoy and Philbrook6 and Fulton and chipman.7 The former experimenters found the reaction-rate constant for silica reduction by carbon-saturated iron to be 20 to 60 times less than the rate constant for chromium reduction. In their work on the reduction of SiO2 in mechanically stirred systems, Fulton and Chipman also found small values for the specific reaction rate and derived a high value for the energy of activation for the reaction. In both of these investigations, the reduction process was assumed to follow first-order behavior. schuhmann8 proposed that the rate-limiting step in this reaction is the diffusion of oxygen from the interface through a boundary-layer film to the bulk metal phase, and Rawling and Elliott9 have reported experimental confirmation of this hypothesis for temperatures below 1600°C. Turkdogan et a1.10 have also concluded that the rate of reduction of silica is a slow process and controlled by the diffusion of oxygen in the metal, but only in the absence of carbon monoxide bubbles at the slag-metal interface. In the presence of bubbles, achieved either by injecting carbon monoxide at the slag-metal interface or by blowing it through the metal and slag, these investigators found a rather rapid reduction of silica which appeared to be controlled by an interfacial reaction involving the de-sorption of silicate ions from the slag-metal interface to the metal phase as silicon and oxygen atoms. In view of the unresolved nature of the kinetics of FeO reduction and the lack of kinetic data for the manganese reaction,

Jan 1, 1968

By Dudley L. Davis, E. C. Peterson

INTRODUCTION THE Darwin District is 30 miles east of Olancha which is 220 miles north from Los Angeles via U. S. Highway No. 6. The ore deposits occur in the Darwin hills that have been elevated above the Darwin Plateau by typical basin and range-type faults. Some of these faults have been active quite recently as shown by the displacement of Quaternary (?) basalt flows and the rejuvenation of erosion in Darwin wash. The ore bodies occur as fissure fillings and replacement of favorable beddings in a thick series of Paleozoic limestones, dolomites, shales and quartzites. Rich oxidized lead-silver ores were discovered in the early seventies. By 1875, Darwin had a population of about 5000, and by 1880 several small mills and smelters had been built. Early exhaustion of surface ores, the isolated location of the district, and fluctuation of metal prices caused intermittent operations until World War II. The district production is estimated at about $3,000,000 prior to 1900 and perhaps $4,000,000 between 1900 and 1945 when Anaconda purchased the major producing mines. For the past two years, daily production has averaged 75 tons of direct shipping and 150 tons of milling-grade ore. At present, 300 tons of mixed oxide and sulphide ore are treated by flotation, the oxidized lead minerals being activated by addition of sodium sulphide after galena and sphalerite have been recovered from the circuit. Extraction averages 85 pct of the lead, 80 pct of the silver, and about 33 pct of the zinc in a bulk concentrate. The mill is designed so that minor changes permit selective flotation of pyritic lead-zinc ores encountered at depth. GENERAL GEOLOGY The oldest rocks in the Darwin hills are a series of Paleozoic limestones, dolomites, shales and quartzites probably Pennsylvanian in age. These rocks have been intruded on the west by the Coso granite batholith and on the east by a granodiorite stock. Numerous sills and dikes grading from orthoclase granite to gabbro are exposed in the underground workings. The sedimentary rocks have been considerably folded and faulted, the most prominent structure being a northwest pitching anticlinal fold, the crest of which lies just west of the ridge line of the Darwin hills. The east limb of this fold has been intruded by the granodiorite stock and east of the stock the sediments show several closely spaced anticlines and synclines. The minor flexures on the west flank of the major fold are structurally important in localizing the ore in the Defiance and Essex mines of the Darwin group. There are three principal systems of faulting and fissuring, most of which are post-intrusive and premineral in age, with minor amounts of postmineral movement. The Darwin tear fault is the largest, most persistent fault in the district. It strikes N 60 to 95°W, dips steeply south and is traceable for about 1o miles. It is a normal

Jan 1, 1947

By Dudley L. Davis, E. C. Peterson

Introduction The Darwin District is 30 miles east of Olancha which is 220 miles north from Los z4ngeles via U. S. Highway No. 6. The ore deposits occur in the Darwin hills that have been elevated above the Darwin plateau by typical basin and range-type faults. Some of these faults have been active quite recently as shown by the displacemerit of Quaternary (?) basalt flows and the rejuvenation of erosion in Darwin wash. The ore bodies occur as fissure fillings and replacement of favorable beddings in a thick series of Paleozoic limestones, dolomites, shales and quartzites. Rich oxidized lead-silver ores were dis'Overed in the early seventies. BY 1875, Darwin had a population Of about 5000, and by 1880 several small mills and smelters had been built. Early exhaustion of surface ores, the isolated location of the district, and fluctuation Of metal prices caused intermittent operations until World War 11. The district production is estimated at about $3,000,000 prior to 1900 and perhaps $4,000,000 between 1900 and 1945 when Anaconda purchased the major producing mines. 'or the Past two Years, daily production has averaged 75 tons of direct shipping and 150 tons of milling-grade ore. At present, 300 tons of mixed oxide and sulphide ore are treated by flotation, the oxidized lead minerals being activated by addition of sodium sulphide after galena and sphalerite have been recovered from the circuit. Extraction averages 85 pct of the lead, 80 pct of the silver, and about 33 Pct Of the zinc in a bulk concentrate. The mill is designed so that minor changes permit selective flotation of pyritic lead-zinc ores encountered at depth. General Geology The oldest rocks in the Darwin hills are a series of Paleozoic limestones, dolomites, shales and quartzites probably pennsyl-vanian in age. These rocks have been intruded on the Rest by the Coso granite batholith and on the east by a granodiorite stock. Numerous sills and dikes grading from orthoclase granite to gabbro are exposed in the underground workings. The sedimentary rocks have been considerably folded and faulted, the most prominent structure being a northwest pitching anticlinal fold, the crest of which lies just west of the ridge line of the Darwin hills, The east limb of this fold has been intruded by the granodiorite stock and east of the stock the sediments show several closely spaced anticlines and synclines. The minor flexures on the west flank of the major fold are structurally important in localizing the ore in the Defiance and Essex mines of the Darwin group. There are three principal systems of faulting and fissuring, most of which are post-intrusive and premineral in age, with minor amounts of postmineral movement. The Darwin tear fault is the largest, most persistent fault in the district. It strikes N 60 to 75°W, dips steeply south and is traceable for about 10 miles. It is a normal

Jan 1, 1949

By T. O. Allen, J. H. Atterbury

Laboratory and field tests during the past five years indicated considerable variation in the penetrating power of commercially available gun perforators. Many of the guns which achieved inadequate penetration in these tests have since been improved. However, recent productivity tests indicated the possibility of inadequate penetration or, at least, ineffective penetration in some wells. Laboratory experiments under simulated well conditions have demonstrated considerable plugging of the perforations, apparently as a result of factors associated with the shooting process and/or the drilling mud in the well at the time of perforating. The restrictions to flow per unit of hole depth caused by this plugging appears to be greater for jet perforators than for bullet guns of comparable diameter; however, because of the greater depth of penetration obtained with the jet guns, the total flow rates appear to he approximately equal. Limited testing with an experimental shaped charge suggests that less shot hole restriction and greater flow rates may result from larger-diameter perforations or other factors related to charge design. INTRODUCTION Gun perforating has been accepted for a number of years as a routine well completion method which is often preferred since it permits more selective operation of producing zones. Nevertheless, questions have continued to arise as to the effectiveness of the communication paths established between the productive formation and the interior of the casing. The basis for these questions has generally been failure to obtain anticipated fluid production rates through gun perforated completions in specific wells. These low productivities, together with the frequent recovery of bullets from well bores, were considered strong evidence of inadequate penetration. Laboratory investigations of the penetration performance of many of the bullet guns available as late as 1948 gave support to these indications. Subsequent electrical analog studiesl,2,3 indicated that the depth of penetration required to provide productivities equivalent to open hole was beyond the capacity of most bullet perforators evaluated in the early laboratory penetration tests. These results, together with the advent of the shaped charge in the field of oil well perforating, stimulated the interest of both oil operators and service companies in gun development. Improvements in gun design resulted in jet and bullet guns which appeared to be capable of providing sufficient penetration for most perforating jobs. However, some wells failed to yield satisfactory fluid production even after being perforated with the more powerful guns, again raising the question as to the effectiveness of the perforating operation. This fact, together with preliminary shooting into targets prepared with formation cores, indicated that factors associated with the perforating process and/or the fluids in the well bore at the time of shooting may reduce effective formation penetration and thereby decrease well productivity. These laboratory and field data prompted another phase in the investigation of the effectiveness of gun perforating: a program to determine the extent and seriousness of perforation plugging under simulated well conditions.

Jan 1, 1955

By J. C. McDonald

A DDITIONAL experimental data are presented in this note on a phenomenon which has been touched on but lightly in the literature. The common magnesium base rolling alloy (AZ31B) contains about 3 pet A1 and 1 pet Zn. When cold rolled, it hardens until it starts to break up in the rolls at 30 to 50 pet reduction. When it is heated after rolling to full hardness, it softens. However, other magnesium alloys have shown themselves capable of being cold rolled indefinitely, provided the ratio of roll diameter to starting gage is sufficiently high. As measured by the tensile test, these alloys actually soften when the reduction becomes large (60 to 90 pct). A subsequent heating at 300' to 500°F can produce hardening of this metal. Heating at higher temperatures (600' to 800°F) causes recrystalliza-tion and softening. Menzen' has shown that a magnesium base alloy can be cold rolled without intermediate anneals as much as 90 pet. The alloy studied, Mg-1.5 pet Mn, softened considerably between 20 and 90 pet reduction, as measured by tensile properties; a decrease in yield strength of 30 pet, and an increase in elongation from 3.2 to 16.7 pet (longitudinal direction of the sheet). However, Menzen gives no data on the reaction of this metal. to heating. Ansel and Betterton2 and Hurst and Hatch3 report a similar effect in Mg-1.5 pet Mn-0.1 pet Ca. Their data show an initial hardening, followed by softening. The former authors also show that the alloy softened by cold rolling will harden when heated at low temperatures, and that these effects are absent in Mg-3 pet Al-1 pet Zn. In the course of work4, 5 some years ago, the author observed similar effects with alloys containing cerium, thorium, or zirconium; but not with elements like aluminum, silver, or zinc. Table IA contains the results of an experiment which shows these effects rather well. A binary alloy with 0.3 pet total rare earths (Mischmetal* added) was rolled hot to 1/16 in. and then annealed to full softness by heating 30 min at 800°F. Rolling was continued at 1.5 pet per pass to 80 pet total reduction on 8 in. diam rolls. The metal was harder after 20 pet work than initially but, at 80 pet reduction, properties were back to their original values. Heating for 1 hr at 450°F produced about the same hardness whether the reduction was 20 or 80 pet. At intermediate reductions, the metal hardened, but not to as high values. Extensive cold rolling may also be carried out on metal hot rolled at temperatures sufficiently low to produce a semihard temper. Mg-0.6 pet Zr was rolled to 0.1 in. at 700° to 800°F, 30 pet per pass. As shown in Table IB, a further cold reduction of 85 pet, at 1.5 pet per pass, definitely softened the metal.

Jan 1, 1959

By W. F. Kieschnick, and W. J. McGuire&apos, Eugene Harrison

This paper concerns the induction and extension of fractures into rock formations as involved in drilling, completing, and production stimulating operations on wells. Conclusions concerning formation breakdown are derived from (I) a review and extension of published analyses relating to mechanical theories of rock stress and the state of stress in the earth's crust and (2) a correlation of field data from fracturing operations. Conclusions concerning the mechanics of fracture extension, which indicate the relationship between fracture dimensions and rock properties, depth, and volume of injected fluid, are tentative and largely establish limits of relationships. These conclusions are derived from stress calculations, limited field data, and laboratory experimental studies. The experimental work involves the study of the stresses at the fracture boundaries and the geometry of pressurized fractures by means of photo-elastic modeling methods. Results of this investigation indicate that a large majority of pressure induced wellbore fractures are vertical, particularly in deeper wells; and variations in the pressures necessary to create and extend fractures can be explained largely on a basis of established rock properties. It is also shown that variations due to tectonic forces should usually be expected to be slight. Other results indicate that during that extension of fractures rather large fracture volumes are temporarily created by the parting of the formation. The purpose of this paper is to present the results of calculations and laboratory experiments concerning the mechanics of fracture induction and extension with a view to broadening existing knowledge relating to these phenomena. It is believed that continued progress in developing knowledge of this type is important to the further development of techniques for drilling and completing wells. When a wellbore is subjected to sufficiently high pressure, fracturing of the formation surrounding the well occurs. This phenomenon is a common cause of lost circulation during drilling operations, is a deliberately planned factor in most squeeze cementing operations, and is the controlling factor in many productivity stimulation operations. The exploitation of formation fracturing in recent years has been particularly impressive in sand-viscous fluid well stimulation treatments which were first introduced to the industry by the Stanolind research group1,2,3 several years ago. The borehole fracturing phenomenon has been analyzed mathematically by application of the principles defining the elastic and inelastic behavior of thick-walled cylinders of homogeneous, isotropic, and impermeable material.1,5,6 This basic argument is re-presented in this paper along with new considerations which strengthen it. In addition to these arguments relating to fracture induction some calculations and experimental results relating to the mechanics of fracture extension are presented. Since the nature of the pressure induced fracture at distances from the well is of great importance in considerations of well stimulation procedures there appears to be a need for an integrated approach which deals with the mechanics of fracture extension as well as with wellbore rupture.

Jan 1, 1955

By Yves Dardel

The literature concerning the remelting of alunlinum and its alloys is very rich. Unfortunately the majority of the papers on this subject have no scientific value, for the theories or explanations are too often in opposition to the laws of physical chemistry. Furthermore only a few of the methods of purification are considered in the literature. Hence it has seemed necessary to the author to sketch a general theory of the purification of secondary aluminum. The purpose of the purification is to eliminate the impurities that the charges, and the atmosphere of the furnaces bring into the bath during the successive remelt-ings. Indeed scrap as well as metal can be used when soiled with oil, greases, water, or others, if it has been sufficiently dried and contains oxides. At the melting point of the metal, the oils and greases are decomposed into their constituent elements H², O2, H²O, co², CO, CH,, and others. These gases are added to the corresponding gases in the atmosphere of the furnace. The impurities introduced into the metal during the remelting will accordingly be the products resulting from the action of these gases on the liquid bath. The quantity of hydrogen that is soluble in aluminum and its alloys is given by the relation of sieverts3 as a function of its partial pressure PH2 in the atmosphere m = K vPH² [I] where K is a constant, which depends only upon the temperature and increases with it. The experiments of Rijntgen and Braun4, RÖntgen and M611er5, Bircum-shaw6 and Winterhagerl have rendered it possible to determine the value of K, when the temperature is less than 1.000°C. One obtains: log K = - 4,702.5T + o 238 [2] Besides its usual significance, the term Ph~ represents also the internal pressure of dissolved hydrogen, since in the equilibrium, that is1 when no gas exchange Occurs between the two phases, the Pressures of hydrogen in the metal and in the atmosphere must be equal. Eq I shows that when the partial pressure of H2 increases the amount of dissolved hydrogen in equilibrium increases, and that, if the contrary Occurs, the quantity of H² should diminish. However, if for any reason the diffusion of hydrogen is hindered and the total amount of dissolved gas remains constant while the temperature decreases, the internal pressure of H² increases until it reaches the value of the hydrostatic pressure. At this point, bubbles of hydrogen appear in the bath and escape out of it. The amount of hydrogen in the metal is then limited by a a depending On the hydro- static pressure, which is practically equal to one atmosphere. Indeed hydrogen does not accumulate in the form of a hydride appearing as a separate solid phase. However1 even the mechanism of the solubility is not yet elucidated. One does not know exactly as yet, whether the

Jan 1, 1949

By George A. Roberts, Arthur H. Grobe

H. H. Hausner (Sylvania Electric Products Inc., Bayside, N. Y.)—I tested the 18-8 stainless steel powder described by Grobe and Roberts and the results were excellent. The powder was compacted and sintered in purified hydrogen to a very low density (approximately 20 pct and more porosity). Where the other powders show very little ductility when sintered to such a low density, the described stainless steel was surprisingly high in ductility. I would appreciate it if the authors could give us some data on a similar powder but without silicon and also data on 430 stainless steel powder. H. S. Kalish (Sylvania Electric Products lnc., Bay-side, N. Y.)—I should like to verify the excellent results obtained by Grobe and Roberts with their pre-alloyed stainless steel powder. It seems to me, however, that their data are conservative and that even better densities and higher tensile strength can be obtained with these powders by the selection of proper particle size fractions. The accompanying data were obtained by sintering compacts pressed from the powder made by Vanadium-Alloys Steel Co. to 0.8 in. in diam about % in. high in a cylindrical double action die without the use of lubricant. The compacts were sintered for 1 hr at 2370°F in hydrogen purified by passing it through a Deoxo unit (palladium catalyst) and a Lectrodryer. Even the density obtained using the as-received (—100 mesh) compacted at 40 tsi was quite high as was the hardness. This indicates that by increasing the sintering temperature slightly above 2350°F the coining and subsequent secondary sintering operation can be avoided. With the — 325 mesh fraction, however, very much higher density can be obtained and a high hardness. I have no tensile data to present, but I feel that it is not too optimistic to expect. that unusually high tensile strengths and good ductility can be obtained in this sintered material on the basis of the density and hardness data. The sintered stainless steel made by the above-described methods came out of the furnace very bright and clean. The purified hydrogen atmosphere is important in sintering stainless steel to reduce the oxide present in the powder. The result of such a sintering is good densification and good ductility of the sintered product. G. A. Roberts (authors' reply)—We are greatly indebted to Messrs. Hausner and Kalish for their discussions of our paper. Their encouraging remarks are greatly appreciated and their confirmatory data will do much to add to the value of the paper. At the present time it is impossible to provide complete data on a similar stainless steel powder without silicon, but we do know that, in general, the properties are slightly inferior. Data on such a powder and on other stainless steel types are to be published in the near future.

Jan 1, 1952

By R. K. Matheson

THE Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 19o tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65° From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. CHOICE OF RAISE A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. TIME SCHEDULE As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1942

By M. K. Yen

The distortion of crystal structures referred to as "biege gleitung",1 "local curvature"2-4 and "deformation bands"5,6 is believed to be an unavoidable characteristic of deformed single crystals. The presence of asterism on Laue photograms of Al single crystals either deformed by pure shear7 or extended in a condition relatively free from the grip effect2 indicates strong evidence substantiating this point of view. The type of localized bending described in connection with the bending test of Al single crystals by Yen and Hibbard8 could conceivably exist either microscopically or submicroscopically in all types of deformation. The purpose of this note is to extend this idea to the postulate of a hypothetical "microbending site," as applied to the mechanism of slip in a general sense. The mosiac structure, as postulated by Darwin,9 is that crystals were actually composed of small blocks which have a linear dimension 10—4to 10-6 cm on the edge and deviate from each other by an angle of about one-tenth of a degree. The following discussion is based on the assumption that when slip is propagated from one mosaic block to the adjacent one, bending of the lattice at the region of their boundary is produced in order to maintain the continuity of the gliding process along a certain slip plane. Consider a two-dimensional diagram of two ideal mosiac blocks on the cross-section perpendicular to the slip plane and containing the active direction of slip. When an external force is applied, the localized bending or "microbending site," would be generated at the region as illustrated in Fig 1A at point B. A schematic diagram of a "microbending site," generated at a mosaic boundary, is illustrated in Fig IB. It may be seen that once the curvature of the bending site reaches sufficient magnitude, the interaction force encountered by pairs of atoms symmetrical with respect to the center of the bending is equal but opposite in sign. Consequently, the overall energy required to displace the atoms near the center is approximately zero.10"12 Based upon the finding that the misalignment between two mosaics is 0.1 degree,9 the assumption is made that "microbending sites" may possibly exist in the region where one plane will have one more row of atoms than an adjacent plane. It is probable that the origin of the bending site will be where the distance between two mosaic boundaries is "2d" as shown in Fig 1A at point B, where " d" is the interatomic distance. Thus, the distance between two "microbending sites" is in the range of about 600 interplanar spacings. In the case of aluminum, the spacing between two octahedral planes is about 2.33 A. The distance between two bending sites will be approximately 2.5 X 10"5 cm. It is interesting to note that according to Woods13 these values approach closely the size of the domains of a cold-worked metal whose minimum

Jan 1, 1950

REORGANIZING AMERICAN ENGINEERS There are in America approximately 500 engineers' organizations of various kinds, and yet it is estimated in many communities that 30 to 50. per cent. of the resident engineers are not members of any society of engineers. There is no enumeration of the engineers of the country, but estimates range from 100,000 to 300,000, the latter number probably including assistants, such as instrumentmen, draftsmen and inspectors, together with professional engineers. These local, state, regional and national organizations are for the most part independent and have no means for cooperation. Steps toward the improvement of these conditions are being taken in a number of localities and have already been taken in others. Many engineers are giving the matter serious attention. American Society of Civil-Engineers took an important action at the June meeting of its Board of Direction, by, authorizing the creation of a Committee on Development of Am. Soc. C. E. This action is now well known to all representatives on Engineering Council. Other Founder Societies axe reported to be considering similar action. Engineering Foundation, at its meeting on Sept. 12, adopted the following resolutions: Survey of Engineering Organizations BE IT RESOLVED: that the Engineering. Foundation is prepared, the four Founder Societies concurring, to devote its strength and its' income, so far as this may he required, to a study of existing engineering organizations, and from information thus developed to formulate a series of constructive recommendations which may he serviceable in guiding the further development of local and national engineering organizations in their relations to the profession of engineering, to the public and to each other, to the end that a foundation may he laid upon which to establish a broadly planned procedure, which, while recognizing and preserving all that has already been accomplished, shall increase the power of American engineers in upbuilding their profession and in the service they render to society; and RESOLVED: that in accepting the responsibility for such an undertaking, it will be the purpose of the Engineering Foundation to organize the proposed research along the broadest possible lines, to call to its aid highly qualified experts, and to avail itself of the help of agencies which may be willing to cooperate; and RESOLVED: that in proposing this research the Engineering Foundation has no desire or purpose to intrude upon the domain of individual organizations; that it does not propose to control the action of any individual or organization; nor to ask the acceptance of its conclusions; but that its purpose shall he to develop a possible procedure, or a series of such procedures, of such evident, merit that they will appeal to those who are likely to be most interested; it will do this in the belief that in so far as its work may justify the confidence of engineers and of engineering organizations, it will bear its own fruitage.

Jan 11, 1918

By W. J. Reagan

All of the material described in the following paper is within the following specifications: carbon, 0.50 to 0.85 per cent; phosphorus and sulfur, 0.04 per cent max.; manganese, 0.60 to 0.85 per cent; silicon, 0.20 to 0.30 per cent. Steels with much lower carbon contents can be handled in exactly the same manner. One of the first things necessary to basic open-hearth slag control is uniformity of charge, particularly as to the silicon content and the percentage of lime charged. Our past work has shown that the silicon content of the charge is more important than the carbon content in determining the carbon at which a heat will melt. We have found that by keeping the silicon content of the charge about 0.60 to 0.65 per cent, and with a lime charge of about 7 per cent (limestone equivalent), our heats melt sufficiently high in carbon to allow a moderate feed of ore and the slag will be of low iron oxide content. In making a heat of 0.75 carbon steel we endeavor to have the heat melt at about 1.20 per cent carbon. The iron oxide content of the finishing slag depends upon the final phosphorus desired; for a given ratio of lime-silica in the slag, the lower the phosphorus desired in the final steel, the higher the iron oxide content of the finishing slag must be. By reducing the lime charge to a minimum, the heats melt faster, and by keeping the silicon content at the desired figure the heats melt with a high SiO2 slag, which has been shown in previous work to give a low iron oxide slag. In most of our work, using a 180,000-lb. charge and with basic pig containing about 1.20 per cent silicon, we use a lime charge of 8500 lb. of limestone and 2000 lb. of burnt lime. The pig charge is about 48 per cent of cold pig, and the charge contains a large percentage of works scrap. This causes a heat to melt with about 1.20 to 1.30 per cent carbon, for a heat that will finish about 0.75 per cent carbon. This gives a heat that will need a feed of about 2000 lb. of ore, and also a slag with an FeO content of about 4 to 5 per cent at melting. The additional FeO obtained from the ore addition will bring the FeO in the slag at tapping to about 6 to 7 per cent. It is necessary to carry quite a fluid slag to prevent pickup of FeO, as a too heavy slag causes FeO to build up in it, giving a finishing slag with a greater FeO than is desired. By adjusting the lime charge of a basic open-hearth heat, a very sensitive adjustment of the slag may be obtained. The figures in Table 1

Jan 1, 1935

By R.K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By H. C. Ray

ABOUT the beginning of 1930, coal preparation had reached the stage where the cleaning of coal by liquid or air had become the order of the day. Since that time many new preparation plants have been installed in spite of the years of depression in the coal industry, and this is indicative of a trend wherein the coal producer found it expedient to manufacture a cleaner product in order to compete with other fuels. It was also about 1930 that, because of the difficulties encountered with fine coal in cleaning plants, dust collectors came into use. Both cleaning plants and dust collectors, therefore, were much discussed at the engineering meetings of the early 1930's. During these meetings the many advantages to be gained through the use of dust-collecting systems were pointed out by Hebley,1 Appleyard2 and others. The great possibilities of new markets for this product were emphasized and discussed at the same time; however, the disposal of the collected dust remained a problem. Since the purpose of dust collecting is to improve the preparation and, consequently, the salability of the coal, it seems illogical to return the collected dust to any of the coal being prepared for market use, as is done in preparation plants that include dust-collecting systems. The logical thing is to dispose of the dust in some useful and practical manner outside of the tipple. As a practical matter, this can be done in one or both of two ways; either by consuming the dust at the mine's own power plant or by marketing the dust direct to the consumer. The latter method not only offers the greatest opportunities, but is the most important, because of inequalities that may exist between the quantity of dust collected and the consuming capacity of the mine's power plant. In considering the more important marketing possibilities, we are confronted immediately with the problems connected with the handling and transportation of so fine a material. It is this problem, rather than the problem of finding new markets, that has been responsible for the lack of progress in the matter of dust disposal. It is the purpose of this paper to point out again some of the potential market outlets, and also to describe an existing system of handling and transporting coal dust. To the best of the writer's knowledge, this is the first and only operation in this country that has handled fine-mesh coal in bulk 50-ton lots direct to the consumer. POtential Markets for Fine-mesh Coal Dust In general, the potential market outlets would include any operation of which the pulverization of coal is a necessary part. To be more specific, a few of the better known operations of this type must include: colloidal-fuel plants, briquetting plants, "sea coal" distributing plants, water-purification plants and, obviously, pow-

Jan 1, 1944

By R. W. Raymond

to same extent, the assumptions tinderlying Dr. Ilu?ley's con alusions. These amrrmptions are: that 'the loss of metal per million tons of trafffc, depends, first upon the circrtnistances under which the rail is worn; secondly, upon the proportions of its various constituents, ancl that the anlorlnt of loss is afEect~d by eacb constitnent in a cer tain ratio, so that if the circunlstances were the same for all tlie mils, the wear per nliilion tons might he upproxi91ately expre~sed by an equation of the form I + Cc + Pp + SR + Mm = R, io wtlioh I is an unknown valne, dependi~.rg on the quantity of iron (and other ingre dients not determined) in the rail, and assumed to be constant for all the rails ; c, p, s, and m are the experimentally determined quan tities of carhon, phosphorus, sulphur, and manganese, as tabulater1 in YIates VT and VII of Dr. Dudley's paper; and R is the experirnen tdlly dcterlnincd wear per million tons; while C, P, S, and M are onknown wfficients. In other words, it is assunled that the differ ence in wear is proportional to a difference in c, p, s, or m, and that the effects of a change in the amonnt of either are independent of the amount of the rest-—within the experinlental limit5 of the problem. It is also assr~med that sulphar, copper, and other ingredients, not determined, are qually present in all the rails, or at least {lo not affect the wear, since I is taken as constant. Dr. Dudley tacitly assumes the coefficient6 C, P, S, and M to be positive; and assigns certain valries to them, by means of which he redom t.he equation to the form I + Pa: = R, x being equal to cc + Es +Mm i Pp, or tjje uanjbe,. of so-called phosphorus units in the rail. But we do not have R directly given under constant circumstances. The varying weights (per engine, car, or train) and the varying epds, we must neglect for lack of data, and assume that in these rwpects the rails examined have been treated srlbstantially alike. But there remain the varying conditions as to track, which mnst he elirninsted. Dr. Dudley gives six clrlsses, four of which contain 8 rails each, and two 16 rails each. Beginning with the 6~st (tangent grade), take the mean of the figures expressing wear for that clam; and continaing tliis process through the other five, we obtain six expressions in quantity of loss 'by wear, which we assome tc, represent, in their differences, the varying conditions of the trarli, with respect to grade and direction. We now take the mean of these moans (giving double weight to the gmiip containing 16 ohwrvafieras). This general rnean is the 10 of metal per million tons of trafio for a rail of avorage constitution under mean ciroumstances.

Jan 1, 1881

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By Richard M. Foose

Five miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. Geology Lower Cambrian Antietam quartzite and the Rilontalto quartzite, stratigraphi-cally older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65" to vertical. The clay crops out at an elevation of about 1000 feet. Origin and Character The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there Are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about loo ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: SiO2, 67.05 per cent; Al2O3, 22.27; Fe2O3, 0.40; CaO, 0.00; TiO2, 1.05; MgO, 0.52; Na20, 0.04; K2O, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1948

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (— 325-mesh) sand assaying 95.5 per cent SiO2, and a very he (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fractioh was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1947

By R. K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943