Search Documents

Discussion of the paper of L. A. DELANO, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 129, September, 1917, pp. 1267 to 1286. L. A. DELANO.-Since this paper was written, our daily mill tonnage has increased, from 2100 tons to 2700 tons a clay. We now use 11,000 lb. of chrome-steel balls of 2 ½ -in. maximum diameter, for an average crushing capacity of 275 tons per 24 hr., this giving a much higher crushing efficiency. I wish to call attention to two typographical errors in my paper as published. On page 1271, Table 1, the screen analysis of ore at the Bonne Terre mill should be stated in inches instead of mesh. - On page 1272, "the rolls average 185 tons per 24 hr., and have shown by test that 250 tons per hour can be maintained" should, of course, read "250 tons per 24 hours." THE CHAIRMAN (0. M. BILHARZ, Miami, Okla.).-Is the increased mill capacity due to improvement in the re-crushing of middlings or to keeping middlings out of circulation and treating them separately? L. A. DELANO.-AS was shown in Mr. Rabling's paper (Bulletin No. 128, p. 1161) the tonnage was raised by about 400 tons by simply changing the arrangement of screen openings in the jig bed and using punched plate instead of woven-wire screen. Then, by adding a ball-mill, we are taking from the jigs a much larger tonnage of middlings than before or as much as the ball-mill will crush. By sending the ball-mill product to tables and flotation, the jig capacity for original ore is increased. CHAIRMAN BILHARZ.-In your opinion, the satisfactory operation of a Hancock jig on a given ore requires adjustment of the length of the different screens and careful selection of screen openings? L. A. DELANO.-I think it does. In order to decide what screen openings to use on the jigs, we did a great deal of experimental work, making screen analyses of the various hutch products, and then hand-sorting the galena, middlings and chat from each size screen to determine the percentage of galena in each. Then adjusting our jig screens, we gradually worked the process up to a very efficient basis. ERNEST GAYFORD, Salt Lake City, Utah.-I would like too ask Mr. Delano whether the work of the Allen cone has been quite as satisfactory as the manufacturers claim for it.

Jan 1, 1918

By G. Richards Gwinn

GRAPHITE is one of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world's high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. TYPES of GRAPHITE USED IN CRUCIBLES Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1945

By George P. Hulst

Prior to 1914, there was little demand for antimony in this country; its use was limited almost entirely to the manufacture of type and bearing metals. Practically no antimony ore was mined here, the market being supplied principally from China, and the alloy was produced by a direct mixing of lead and antimony. The great world war, with its demand for shrapnel in hitherto undreamed of quantities, precipitated a great boom in the price of antimony. Nominally quoted at 6 c. to 7 c. in 1914, the price increased by leaps and bounds to 45 c. in March, 1916. Under the stimulus of high prices many small mines were opened, for it became profitable to work ores containing as low as 20 per cent. antimony. High-grade sulfide ores (stibnite), containing 55 per cent. to 60 per cent. antimony, were received from Bolivia, China, and Alaska. Low-grade sulfide ores, running from 20 per cent. to 45 per cent., were produced in Nevada, California, Idaho, Utah, and Mexico; much of this ore was fairly rich in silver. The principal oxide ores came from Mexico and Oregon. The following analyses are representative of various types of antimony ore: Sb Pb Cu AG AU SIO2 Be S CaO Zn As Oxide ore.......... 25.09 46.02 0.95 0.40 10.98 0.30 0.22 Sulfide ore......... 55.20 15.12 1.05 19.87 0.40 0.25 Sulfide ore......... 37.16 11.30 0.10 34.0 7.60 0.50 17.05 7.40 0.36 0.10 Sulfide ore......... 41.55 18.00 0.20 76.0 0.04 5.60 0.25 18.17 0.85 0.25 0.10 The International Lead Refining Co. fortunately was equipped to handle these ores through residue and blast furnaces. The charge consisted of a variety of sulfide ores containing Sb 20 to 60 per cent. and SiO2 6 to 45 per cent., oxide ores containing Sb 20 to 40 per cent. and SiO2 10 to 45 per cent. Secondary materials, such as battery plates, battery mud, lead oxide, paint, etc., together with refinery skims, softener skims, and other refinery byproducts, were treated along with the antimony ore to furnish the lead required. All silver-bearing antimony ores were treated in the residue furnace, the sulfur, iron, and copper forming matte that carried part of the silver, the balance going into lead bullion. The antimony slag produced was sufficiently low in silver to warrant being smelted in the blast furnace to antimonial lead.

Jan 1, 1921

The passing of Benjamin Bowden Lawrence in January, 1921, was a distinct loss to the engineering profession. Mr. Lawrence had a genius for reviving abandoned mines and developing them into substantial producers. A notable example of his work in this line was the Dives-Pelican near Georgetown, Colo. While on an exploring expedition in 1888, he examined this old mine and was convinced that bonanza ore still existed there. He located the owners of the property, and induced them to place sufficient capital at his disposal to enable him to re-open and explore this mine. So confident was he of the outcome that he undertook this work on a profit-sharing basis without salary. Within eighteen months the old Dives-Pelican was operating profitably, and for the following ten years it paid very substantial dividends. The late Theodore N. Vail was one of the owners of this old mine, and many years later, at a dinner given to Mr. Lawrence by the Alumni of Columbia University, Mr. Vail told the story of the resuscitation of the Dives-Pelican by Mr. Lawrence, and declared that the dividends he himself had received provided a large part of the funds that made possible the realization of his dream of establishing the long-distance telephone in this country. The E1 Cobre mines at Santiago de Cuba also owed their renewed life to Mr. Lawrence. Under his management, these mines produced and shipped several million pounds of copper per year. He was for several years consulting engineer for the Kerr Lake and other silver mines in the Cobalt region; the Kerr Lake became famous as a silver producer. Mr. Lawrence spent more than twenty years of his life in the mining camps of the West. He was but twenty-one years of age, and only a few months out of college, when he was appointed manager of the great Chautauqua Lode (a silver mine) located on Glacier Mountain near Montezuma, Colo. Here, isolated in the mountains for several months each year by ice and snow, he worked for five years to make these mines Pay. He possessed unusual breadth of vision and human understanding; he had ''personality plus," and when he opened an office in New York City as consulting engineer he quickly rose to an enviable position in his profession. Young engineers worked with enthusiasm under his guidance. He carefully selected his men, discussed fully with them the plans and policies to be pursued, then left them free to accomplish results in their own way. This attitude developed individuality and resourceful-

Jan 1, 1922

By Eugene F. Poncelet

This paper attempts to analyze the phenomena involved in the fracture of brittle solids by simple compression. Glass squares standing on edge, and compressed between two parallel steel jaws, developed jagged fractures, roughly parallel to the compression. Polarized light disclosed the presence of high local stress concentrations indicating poor contact all along the contact surfaces with the steel jaws. Teszar has shown that partial contact between the jaws and such a compressed solid causes tensile stresses in the free surfaces of the solid normal to the compression. Furthermore, Scoble has shown that in brittle solids fractures are caused by, and develop normally to, a sufficient tensile stress. It follows that such "partial-contact" cracks must be expected. With optically flat jaws and specimens, no "partial-contact" cracks developed. Instead, very smooth cracks vertical to the compression appeared 'upon release of the pressure. Investigation showed that the friction with the rigid steel opposed the return of the glass to its original width, after creeping on the steel as compression built up, thus setting up tensile stresses in the glass surfaces. It was not found possible to eliminate these "release" cracks. Compressed to destruction, such specimens flew to dust. A Microflash photograph taken during the explosive disintegration revealed: (I) oblique parallel fragmentation cracks, 30" off the direction of the compression; (2) transverse forking fragmentation cracks, normal to the former; (3) release cracks parallel to the compression; (4) a disintegration cloud. Given a distribution of submicroscopic cracks of random orientation throughout the glass, Griffith has shown the highest tensile stresses to be located at the tip of the cracks 30" off the direction of the compression. Although the preexistence of such cracks or flaws in unstressed glass is doubtful, they can be generated by the distorting forces set up by the compression itself. Atoms, in a structure held together by Morse-type forces or bonds, have under tension both a stable and an unstable state-of equilibrium. The difference in energy level between these two states is a function of the tension, and this difference must be borrowed from the thermal energy level of the bonds to reach the unstable state and result in a broken bond. As the fraction of the bonds having at any instant a sufficient thermal energy level is a known function of that level, it is possible to determine, in function of the prevailing tension, the fraction of the bonds that are broken. Upon breaking of the bond uniting two atoms at the tip of an advancing crack, the two atoms accelerate away from each other, causing in the solid propagation of a

Jan 1, 1944

By Eugene F. Poncelet

This paper attempts to analyze the phenomena involved in the fracture of brittle solids by simple compression. Glass squares standing on edge, and compressed between two parallel steel jaws, developed jagged fractures, roughly parallel to the compression. Polarized light disclosed the presence of high local stress concentrations indicating poor contact all along the contact surfaces with the steel jaws. Teszar has shown that partial contact between the jaws and such a compressed solid causes tensile stresses in the free surfaces of the solid normal to the compression. Furthermore, Scoble has shown that in brittle solids fractures are caused by, and develop normally to, a sufficient tensile stress. It follows that such "partial-contact" cracks must be expected. With optically flat jaws and specimens, no "partial-contact" cracks developed. Instead, very smooth cracks vertical to the compression appeared 'upon release of the pressure. Investigation showed that the friction with the rigid steel opposed the return of the glass to its original width, after creeping on the steel as compression built up, thus setting up tensile stresses in the glass surfaces. It was not found possible to eliminate these "release" cracks. Compressed to destruction, such specimens flew to dust. A Microflash photograph taken during the explosive disintegration revealed: (I) oblique parallel fragmentation cracks, 30" off the direction of the compression; (2) transverse forking fragmentation cracks, normal to the former; (3) release cracks parallel to the compression; (4) a disintegration cloud. Given a distribution of submicroscopic cracks of random orientation throughout the glass, Griffith has shown the highest tensile stresses to be located at the tip of the cracks 30" off the direction of the compression. Although the preexistence of such cracks or flaws in unstressed glass is doubtful, they can be generated by the distorting forces set up by the compression itself. Atoms, in a structure held together by Morse-type forces or bonds, have under tension both a stable and an unstable state-of equilibrium. The difference in energy level between these two states is a function of the tension, and this difference must be borrowed from the thermal energy level of the bonds to reach the unstable state and result in a broken bond. As the fraction of the bonds having at any instant a sufficient thermal energy level is a known function of that level, it is possible to determine, in function of the prevailing tension, the fraction of the bonds that are broken. Upon breaking of the bond uniting two atoms at the tip of an advancing crack, the two atoms accelerate away from each other, causing in the solid propagation of a

Jan 1, 1944

By F. M. Waring

produced when zinc is substituted for a certain amount of tin are decidedly unsatisfactory. The substitution of aluminum for tin is entirely impractical, and such castings are worthless. This does not, however, exhaust all the possibilities of substituting other metals for tin in the copper-tin-lead alloys, but it is my opinion that the substitution of any other metals, in those alloys, can be made only by sacrificing the quality of the alloy. The possibility of substituting alloys of an entirely different type presents an attractive field for research. The copper-tin-lead alloy has attained its position as the most desirable bronze bearing alloy, but this does not mean that some other alloy may not be found which may give equally good or better results. In the search for such a substitute alloy it should be borne in mind that a bearing metal should possess the following properties: (1) It should be sufficiently rigid to support the load or resist the impact, but yet not so brittle that it will easily crack. (2) It should have as great a yielding or plastic nature as is consistent with its ability to support the load or resist the impact without deformation of the bearing as a whole. (3) The ideal structure combines a hard matrix to support the load and a softer metal or alloy contained within such matrix, to permit the bearing surface to adjust itself to irregularities of service. (4) It should be easy to handle in the foundry and machine shop. (5) It should be capable of being remelted without deterioration. (6) For use in babbitt-lined bearings, it should be capable of being tinned, so that the babbitt can be applied thereto. (7) It should have good heat conductivity in order to dissipate the heat generated by friction. Pennsylvania Railroad Anti-friction and Bell Metals F. M. Waring," Altoona, Pa.—Thc necessity for conserving tin has recently been very forcibly brought to the attention of all consumers, and efforts are now being made to reduce the tin content in certain alloys or to substitute other alloys not containing tin. The approximate composition of the non-ferrous alloys in general use on the Pennsylvania Railroad are given in the accompanying table. Phosphor bronze is used principally for rod bushings, main-rod brasses, and crosshead shoes. Ex. B bronze is used to a small extent for backs of car and coach bearings, but the majority of these are now made of the car-journal bronze, which contains, on the average, about 5 per cent. tin.

Jan 1, 1919

By T. Koulomzine

The theory of the Askania mag-netometer, as well as a complete discussion of all factors influencing magnetometer readings, is very ably described by J. Wallace Joyce.1 We will assume that the reader is thoroughly familiar with this theory and we will use whenever possible the same notations for the physical values involved in the theory. On the other hand, we believe that the principal formulas of the magnetometer can be deduced much more easily by the use of differential calculus than by the methods employed by Joyce. Consequently, we are presenting herewith a resumé of the theory of the vertical magnetometer in order to determine the correct formula of the temperature coefficient which we propose to compensate. Short Theory of the Vertical Magnetometers We shall accept the following notations: m = total mass of the magnet system, in grams. g = acceleration of gravity, in dynes. a = projection on the axis of the magnet system of the distance between the axis of support and the center of gravity of the magnet system, in centimeters. h = projection on the perpendicular to the axis of the magnet system of the distance between the axis of support and the center of gravity of the magnet system, in centimeters. M = 2pL = M, magnetic moment of the magnet system. Z = vertical component of the earth's magnetic field. ? = deflection angle of the magnet system. = focal length of objective lens in the optical system S = scale reading. In a vertical magnetometer the axis of the magnet system is kept horizontal within 2". Therefore, referring to Fig 1, we see that the magnetic torque of the magnet system influenced by Z must be counterbalanced by the gravity torque. MZ cos ? = mga cos ? + mgh sin ? or dividing by cos ? MZ = mga + mgh tan ? If we now move to another magnetic station and the temperature conditions change, the values of all the variables will change also: M, a, and h under the influence of temperature. 2, both with time and space. ? and S, as a result of all the above changes. Taking increments in Eq 2 we obtain: (Mo + ?M)(Z + ?Z) = mgao + mg?a + mg(h + ?h) tan (? +??) but tan (? +??), because ? is small, can be replaced by tan ? + tan ??; in fact tan (?+ ??) = sin ?.cos ?? + cos ?.sin ??/ cos ?.cos ?? — sin ?sin ?? but sin ? sin ???0 tan (8 + ??) ? tan ? + tan ??. Fur-thermore, neglecting all terms of the equation containing two differentials becomes: or a differential and a tan ??, Eq 3

Jan 1, 1950

By W. M. Corse

I bring this investigation to your attention to emphasize the needless waste attendent upon the use of tin plate with an unnecessarily heavy tin coating. With our present knowledge, we are unable commercially to produce coatings as light as the lower weights used in this test. If, however, future research should develop means to this end, the resultant product would meet all practical requirements, and a very considerable saving in pig tin would result. DISCUSSION G. H. Clamer.-—The National Canners' Association is studying the action of fruit juices, etc., on solders. Of course these tests will take quite a long time, and we hope by that time the war will be over and there will be no need for conserving tin for war purposes. Germany for a great many years has prohibited the use of more than 37 per cent. of lead in alloys used in contact with food products. The eutectic composition is 37 per cent. of lead and 63 per cent. of tin; alloys containing more than that percentage of lead have some free lead. J. W. Richards,' South Bethlehem, Pa.—A great deal of conservation can result from the packing of dry foods in cartons and in fiber packages instead of using sheet tin. Many of the boxes used for packing things other than food are frequently made of sheet tin because it prints and lithographs well; these could be made of sheet iron coated with copper or some other substitute metal which prints equally well. The Aluminum Bronze Industry W. M. CORSE,† Mansfield, Ohio.—The conservation of tin, in view of the shipping situation, is one of great importance. Several methods of conservation can be employed: 1. Reduction of the amount of tin in an alloy or compound. 2. Substitution of an entirely different metal or compound for tin. 3. A combination of the first and second methods. The second method is the one that I wish to discuss. Metallic aluminum, has been known for a long time, and its use in copper alloys was discovered about 1855 by Lord Percy. The high cost of production of metallic aluminum retarded its commercial development, and it was not until the discovery of the electrochemical processes for its production that it came to be known as a common metal. I have been particularly interested, for the past few years, in working with the alloy known as aluminum bronze, which is usually composed of approximately 90 parts of copper and 10 parts of aluminum, by weight.

Jan 1, 1919

The Telfer Project, one of the world's newest gold mines, is located about 300 km (190 miles) northeast of the Mt. Newman iron ore project in the northern part of Western Australia. The first mineral claims were staked in 1972; and by mid-1975 ore reserves of 3. 8 million mt (4. 19 million st) of 9.6 g per mt (0. 28 oz per st) ore had been indicated. It is interesting to note that Newmont spent more than 10 years and A$10 million in Australia for extensive mineral exploration before finding the Telfer deposit, and then spent approximately A$3 million in exploration and feasibility engineering on Telfer. Including this A$3 million, a total of A$27 million was spent to complete construction of the mine, village, gold treatment plant and associated roads, airport, water and services. Over 50% of the capital cost is in the metallurgical facility, or approximately A$10, 000 per ton per day. All economically significant gold mineralization at Telfer occurs in a series of layered quartz-limonite reefs in which the former pyrite has been oxidized to limonite to a depth of 100 m (330 ft). The most important gold reef occurs at the base of the siltstone-shale horizon within the enclosing sandstone dome -like structure. At the Main Dome structure the dipping ore horizons will be mined to a vertical depth of about 60 m (200 ft) by open-cut methods. The waste-to-ore ratio is approximately 12:1. Eventually 44 million mt (48. 5 million st) of ore and waste will be mined. Mining of the waste is by contract; however, the ore and a thin layer of waste is company-mined. Dilution from mining the geological ore reserve is about 10%. The ore is completely oxidized and the gold occurs free within the reef, material as discrete particles of varying but mainly fine grain size. Most of the gold is "free milling"; that is, over 50% of the gold is coarse enough to be recoverable by gravity concentration. Two duplex mineral jigs receive the two cyclone underflows from the grinding circuit. The rougher jig concentrate is up-graded on a continuous strake from which the concentrate is tabled to produce a final free gold product. Jig tailings are returned to the ball mill and the concentrates are amalgamated. Gold amalgam is pressed, retorted, and melted into gold bars. The gravity gold recovery circuit is the same as was used in many of the gold mills in California in the 1930s.

Jan 1, 1981

By Lucien Eaton

IN anticipation of a shortage of labor for hand-tram-ming at the Cliffs shaft mine of the Cleveland-Cliffs Iron Co. at Ishpeming, Mich., early in 1923 three 4-ton Goodman storage-battery locomotives, equipped with Edison batteries, were purchased. Storage-battery locomotives were chosen for this work because the expense and time required to put up trolley-wire and to bond the rails of the complicated system of tracks on the levels, where the locomotives were to be used, would not have been warranted by the amount of ,ore to be handled. The only changes in the tracks necessary for storage-battery locomotives were new switches and extra ties and braces on curves. The tracks were 24-in. gage, and were laid with 20-lb. rail. Edison batteries were chosen, because it was desired to charge the batteries from the trolley circuit already, in the mine, and this would have been impracticable with lead batteries. Each locomotive is equipped with 126 A-4 Edison cells, which are charged in series from the 240-volt trolley circuit while the trolley locomotives are running; and are discharged in parallel in two banks of 63 cells each. These locomotives were so successful that later 5 smaller locomotives, weighing 11/2 tons each, were pur-chased for use e with cars that are filled by hand and on levels where the amount of ore handled is small. These locomotives, built by the Geo. D. Whitcomb Co. of Rochelle, Ill., are equipped with batteries of 40 A-4 Edison cells each, the cells being the same as those, on the larger locomotives. They are charged from mer-curial-are rectifiers. These locomotives are operated by the trammers themselves, and have not special oper-ators like the larger machines. The trammers are all young men of American birth, and take quickly to the operation of machinery, and the simplicity of the con-trol on these locomotives has made special training unnecessary. A survey of the results was made by the A. C. Nielsen So., an excerpt from which follows: Eight Edison-equipped battery locomotives are now in use at an Ishpeming mine of the Cleveland-. Cliffs Iron Co. This equipment was installed to take the place of men who formerly pushed loaded cars by hand. Results have been very satisfactory and the de-pendable, trouble-free operation of the Edison batteries is considered to have been an important factor in the effectiveness of the new hauling method.

Jan 3, 1927

I HAVE now traversed for you in the small and fragile bark of my writing all the shores of the deep and spacious sea embracing the uses of material fires, drawn on by my own desire to enrich you with more learning and with the procedures of these things, as much as to satisfy your demands. Having through the grace of God arrived at the appointed end of my voyage and neither knowing nor perceiving a way of going farther, I had decided to furl the [167] sails and cast die heavy anchors into the water in order to enjoy in tranquillity respite from my sailing, when I was warned by my pilot that before I could disembark I should turn my glance backward and reexamine my work in detail to see if there were any part that had by chance remained undescribed in the obscurity of silence. When I did this there immediately appeared in my mind's eye the many sublimates and smoky tinctures that had been made by the burning and most powerful fire of love. I need not say that I knew of it in far-off countries or from the knowledge of others, but I knew it in my own breast and as my very own and can therefore surely esteem it as hotter than all the other fires that the world calls by that name. Although today its sparks and living flames are spent because of my cold and hoary season, nevertheless it is true that the memory of acts of love of long ago still remains with some smoke and warmth. Therefore, since in this work of mine I wish to describe for you the effects and powers of fires, I should logically have spoken of this before any of the others, because of its actual nearness and the great acquaintance I had with it. But since I have had the glance of my intentions directed at distant things, I have behaved as one does who does not see where he places his feet because he is looking at the sky, or as one who thinks about the affairs of others and forgets his own. But now I do not wish to pass over this thing and I wish to correct my error, particularly in order to provide a happier ending to my written work than by remaining among the horrible uproar of guns, powder, and saltpeter, which would be a harsher ending than speaking of love. Never-

Jan 1, 1942

HenRy Clay FRick, a pioneer in modern coke and steel industry and, in more recent years, one of the outstanding financiers of America, died on Dec. 2, 1919, at his home on Fifth Avenue, New York. Although he had been ill since election day, when he had an attack of indigestion which developed into ptomaine poisoning, his death was a surprise to all. He is survived by his widow, Adelaide Howard Childs Frick; a son, Childs Frick, one unmarried daughter, Helen C. Frick, and four grandchildren. A quiet funeral service was conducted at the Frick home on Wednesday afternoon by the Rev. Dr. Leighton Parks, pastor of St. Bartholomew's Episcopal Church. This was attended by members and very intimate friends of the family, Trustees of the Metropolitan Museum of Art, Officers of the Links Club, and Directors of the United States Steel Corpn. Henry Clay Frick was born Dec. 19, 1849, in West Overland, Westmoreland Co., Pa. His father, John W. Frick, was a farmer of Swiss ancestG, and his mother, Elizabeth Overholt Frick, a member of an old Mennonite family. Until he was sixteen, he spent his time at school, on his father's farm, and in his grandfather's distillery, where he kept books. He attended Otterbein University, in Ohio, for a year. Frick, learning that coke was an essential of the already rapidly developing steel business, early invested every cent he could get in coking-coal lands. With the help of an associate of his grandfather, he formed the corporation of Frick & Co., coke dealers, and acquired fifty-one ovens in the Connellsville region and 300 acres of soft-coal lands. During the panic of '73, with the help of Judge Thomas Mellon, a Pittsburgh 'banker, he bought out his partners and while coke was selling at 90 cents a ton enlarged his purchases of suitable lands. Later, the price of coke increased until it was selling at $5 a ton. Before he was 30 years old, Frick was rated a millionaire. Association with CaRnegie In 1878, he sold an interest in the business Do E. M. Ferguson of New York, and later a share to Mr. Ferguson's brother. Four years later the business was reorganized into the H. C. Frick Coke Co. with vast coal lands, great banks of ovens, and a capitalization of $2,000,000. Then began his association with Andrew Carnegie. He exchanged a part of his coke interest for shares in Carnegie Brothers of Pittsburgh,

Jan 1, 1920

By Rosewell H. Johnson

Discussion of the paper of ROSWELL H. JOHNSON, presented it the San Francisco meeting, September, 1915, And printed in Bulletin No. 102, June, 1915, pp. 1291 to 1294. WILLIAM A. WILLIAMS, San. Francisco, CaI.-A sliding. scale of royalties was proposed to the Department of the Interior in connection with the fixing of royalties to be charged upon oil leases made on the Osage Reservation in Oklahoma. The possibility of evasion and difficulty of enforcement required close inspection to satisfy all interests, particularly in connection with the exemption from royalty on oil to equal maintenance and interest on the junk. Mr. Johnson discusses the block method, the period method, and the cumulative method, and favors the adoption of the cumulative method with a proviso that the wells should be permitted to be pumped until the gross income is as low as the maintenance cost, which would mean exemption from royalty on the smallest wells. He recommends that depth be the variable factor upon which the sliding royalty is based and suggests that on partially developed territory in the Osage, the royalty be one-sixth for oil wells averaging less than 2,000 ft. in depth, one-eighth for wells from 2,000 to 3,000 ft., and one-twelfth above 3,000 ft.; for the rest of the Osage he suggests one-eighth above 2,800 ft. and one-twelfth below that depth. The net result, if Mr. Johnson's suggestions had been accepted in the Osage, would have been to reduce the then existing rate of royalty and considerably increase the cost of administration. The difficulties in determining the size of wells to be exempt and the possibility of obtaining oil at different depths in the same well might lead to complications which are avoided by charging a flat royalty as now universally charged throughout the United States. It is not uncommon to reduce the royalty when the production of the wells becomes unprofitable at an existing rate of royalty, accomplishing very much the same results as Mr. Johnson has attempted to accomplish by the cumulative royalties, and probably in a manner far more satisfactory to the operator and the lessor. A. C. MCLAUGHLIN, San Francisco, Cal.-The net revenue of the well depends, first, on the cost of production; second, on the amount of oil produced; therefore it would be impossible under Mr. Johnson's system to set a royalty which would be fair to all concerned. If it is impossible to set it at the beginning, it is certainly further impossible to do it from day to clay. I think it is entirely impracticable of application.

Jan 12, 1915

By G. Richards Gwinn

Graphite is one .of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world's high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. Types oF Graphite Used in Crucibles Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1948

By Mark Sheppard

DURING the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the over- burden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semi- circle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and 800 ft. of 4-in. spiral steel flanged pipe. The connection from the pump

Jan 1, 1938

By William Clark

A bean placed at the bottom of tubing in flowing wells is not a new idea. In fact, a device which in effect was a bottom bean was patented prior to 1890 by John D. Rockefeller. Because of the limited use of the bottom bean, prior to 1922, when it was installed in a few wells in the Santa Fe Springs field, California, the knowledge of the results of its operation is very meager. Since then various oil operators have experimented with bottom beans, but most of the records of the results obtained by their use are unavailable. For the past year or two, more attention has been directed to this method of producing wells; the theory and best means of application have been studied, and accurate records maintained. In theory, the use of bottom beans in flowing or gas-lift wells should secure certain advantageous results. With the exception of flow friction of the tubing and flow lines, there is no back-pressure held on the rising column of fluid. Thus severe beaning is possible with no danger of killing the well by too heavy a fluid column, a condition that often exists when a surface bean is used. The whole energy of the gas expanding to atmospheric pressure is utilized to lift the fluid in the well. The same effect is obtained when flowing a well through open tubing or casing. In using a surface bean this energy of expanding gas is wasted into the flow lines beyond the bean, because the fluid has reached the surface by the time the restriction is reached and the work of the gas performed. The bottom bean affords an efficient use of the expanding force of gas, utilizing less gas to raise the same amount of oil, hence allowing for lower gas-oil ratios. The flow restriction being at the entrance to the flow string, a more uniform mixture of gas and oil enters the tubing and a steadier backpressure is held on the well. The uniform mixture and high velocity attained while flowing through the bean, which is above the critical velocity required to suspend a spray condition of gas and oil, prevent slippage of gas, surging and heading with its resultant strain on the casing. The advantageous conditions allow positive control of production in gas-lift wells within limits set by the bean size and amount of input gas; and probably help to prevent sanding up of a well and the coning

Jan 1, 1931

By E. C. Harder

J. T. SINGEWALD, JR., Baltimore, Md.-I might say a word further in regard to the Miguel-Burnier district. I am sorry Mr. Harder is not here. I had hoped to be able to ask him a few questions in regard to some of the features of those deposits. This Miguel-Burnier district is the other district that I referred to that lies in the State of Minas Geraes. The interpretation that Mr. Harder gives to, these deposits is the same as that given by Harder' and Chamberlin in a previous paper, and that is that they consist of lenticular deposits of sedimentary origin in a series of rocks that also include lenses of limestone, but they seem to think that the manganese ores occur at a definite horizon and at a horizon different from the limestone. We found that the manganese ores occur at several horizons, as also do the limestone lenses, and the limestone masses are of the same shape as the manganese orebodies, so that our own feeling was that these manganese ores simply represent concentrations within the zone of oxidation formed as. a result of decomposition and replacement of this limestone. To the east of Miguel-Burnier there is a big bend in the railroad which cuts through, at right angles to the strike, this series of rocks. Here is shown very well both the local character of the limestone lenses and the local character of the manganese lenses in that, though the distance across the bend is only a couple of hundred yards, the limestone and. ,manganese lenses do not match up at all, and it also shows plainly that both occur at more than one horizon.. Consequently there is no reason why the manganese ore could not represent alterations of this limestone. The mine workings do not as yet give very definite information on this point in that they are all comparatively shallow and within what would be the zone of oxidation so that what they will grade into below that depth, we do not know. On the other hand, the character of the ore suggests that it may, represent such -a product in the zone of oxidation in that it tends to be quite earthy; whereas, if the manganese had been there originally as such it would have undergone the same metamorphism that the other rocks have undergone and one would have expected that it would have been converted into a hard manganese ore that would today stand out pretty much as do the iron ores of that same region and not have the soft, earthy texture which is a prevailing characteristic.

Jan 4, 1917

By G. Richards Gwinn

Graphite is one .of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world's high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. Types oF Graphite Used in Crucibles Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1948

By McHenry Mosier

MeRcuRy is one of the strategic metals of which the supply has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributed substantially to increased production of mercury in the United States and to consequent accumulation of Government stocks. Other contributing factors have been higher prices for mercury and Government loans to operators. The Bureau has undertaken 13 exploration projects, 10 of which have been completed. This work has comprised 28,376 ft. of several types of drilling and 23,798 lin. ft. of surface trenching, and has indicated commercial ore containing 34,800 flasks of mercury and marginal ore containing 26,200 flasks, a total of 61,000 flasks; equivalent, respectively, to domestic production for 8 months, 6 months, and 14 months. As Government stocks are now adequate, domestic production (currently at the rate of 50,000 flasks per year) is gradually being curtailed through Government control of labor and operating supplies. Introduction Mercury was one of the seven metals designated as strategic by the Army and Navy Munitions Board in 1939, when Congress appropriated funds for the investigation of domestic sources of supply of war minerals. The Bureau of Mines immediately started a limited search for strategic minerals, but the first mercury project was not begun until December 1940. The U. S. Geological Survey assisted in the search for cinnabar by contributing information on domestic mercury deposits, preparing maps, and making geological studies of exploration projects. The present high rate of production of mercury in the United States was encouraged by the increase in price to $196 per flask at New York (Fig. I) and Government loans to operators for mine development and plant construction. The Bureau of Mines has issued, for restricted distribution subject to wartime controls, 13 War Minerals Reports on individual mercury deposits (listed in appendix A). In March 1942 it also published a Progress Report of the Metallurgical Division, R. I. 3627, Cinnabar-reduction Plants of the Southwestern Arkansas Quicksilver District. Uses of Mercury Mercury and its compounds have more than 3000 uses. Its principal use is as a catalyst in the manufacture of gases for chemical warfare; the next largest is in pharmaceuticals. Mercury is essential also for: (I) certain electrical apparatus, (2) industrial control instruments at many war plants, (3) munitions, including blasting caps, (4) insecticides in agriculture, (5) antifouling paint for ship bottoms, (6) dental preparations, (7) general laboratory use, and (8) amalgamation of free-milling gold ores.

Jan 1, 1949