Search Documents

By Francis M. Rich

BEFORE the world-wide depression, the primary purpose of most blast-furnace operators was to produce a maximum tonnage of pig iron per day for each furnace in blast. Some attention was paid to the conservation of labor and raw materials, but the idea was well established that low-cost pig iron was attainable only when each furnace was producing a high tonnage. After the depression had set in, the picture changed considerably. Each blast-furnace operator was forced to run his plant in a manner that best fitted the economical set-up of his company. A great deal of thought was expended on the different methods of operation, always with the idea of making each product in a way that would best serve his company financially. Because of this abnormal condition, the blast-furnace man was compelled to indulge in various practices of which many had been believed to be next to impossible up to that time. The ultimate purpose of these innovations was either one or a combination of the following: 1. To produce only enough pig iron for immediate consumption at a minimum cost. 2. To produce gas for boiler or mill use to supplant some higher priced fuel. 3: To consume the coke produced at the coke plant, which was often viewed as a byproduct. 4. To protect the cash position of the company. These conditions were met by diverse methods, some of which were: 1. Slow or decreased wind. In some instances the blast blown was held as low as 25 per cent of the normal volume. 2. Intermittent operation, in which the furnaces were shut down or "fanned" at frequent intervals.

Jan 1, 1935

By B. Silliman

The regions of New Mexico referred to are in Socorro, Grant, and Dona Ana counties, and a portion of Lincoln County, embracing in the aggregate a very large area, of most of which our knowledge is as yet very fragmentary and superficial. It is only very recently that large portions of this region have been accessible. It has been full of danger from hostile bands of wandering Apaches, whose murderous raids have slain many adventurous miners and seriously prevented developments. But this evil has now been largely abated, and in many of the mining camp of this region there is no longer any danger from this cause. SOCORRO MINES. About three and a half miles back of the old Mexican town of Socorro, on the Rio Grande, chief town of the County of Socorro, are two or more large veins of heavy spar, cutting across the fat* of Socorro Mountain in a northeast and southwest direction, and dip ping at an angle of about forty degrees into the body of the mountain. These veins are in rhyolite, and, so far as could be seen in openings on the Torrence Mine, which I examined, are without any clay parting or selvage. The average thickness of the Torrence rein may be about five feet, the thickness varying from pne or two feet to thirteen feet. Upon the cleavage planes of the heavy spar occurs, in visible patches, of a waxy Iustre and gray color, silver chloride, which gives value to the vein, from a few ounces up to one hundred and twenty ounces to the ton, averaging about forty ounces, as I

Jan 1, 1882

By Jed H. Mosgrove

One of the most interesting of all the subjects required of persons studying the different facets of coal mining is coal mine gases. Some mine gases have been a real problem since the very beginning of underground mining, and in the early days there was insufficient knowledge to cope with them. The history of mining shows that until about the last 50 years, much work was done primarily by the hand methods which are primitive by today's standards. Miners had to contend with gases without the aid of enclosed lighting, permissible mine machinery, sophisticated testing devices, and high-pressure ventilating fans. In early days the miners were not educated about the different mine gases nor did they have the technical equipment to determine the actual composition of the deadly atmospheres they encountered. They simply applied a descriptive term to each gas or mixture of gases depending on its, effect on a person or the surrounding atmosphere. The gases or mixtures of gases were then referred to as "damps," a term which was probably derived from the German word "damps," meaning vapors or gases. The more common damps encountered were : Blackdamp A condition of the atmosphere in which a miner's light would be extinguished and in which breathing would be difficult, sometimes even resulting in suffocation. An atmosphere deficient in oxygen which could contain a combination of any of the mine gases. Firedamp A flammable mixture of methane and air which would either burn or explode when ignited. White Damp A mixture of gases containing carbon monoxide, most often found in mines during fires or after explosions.

Jan 1, 1981

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By Wilhelm Borchers

In all special branches of the chemical and metallurgical industries, in which large electric furnaces became necessary for carrying out new processes or for the improvement of old ones, the development of the electric furnaces took place on much the same lines. The endeavors to make a success of a new idea brought forth many ingenious designs, which, however, almost without exception, furnished the proof that the safest and shortest way to practical success is the utmost simplicity of construction of the necessary apparatus. Our knowledge of the qualities of materials for building electric furnaces and of the constituents of the furnace-charges, especially their electric conductivity and their chemical affinity towards one another at high temperatures, is still far from being complete, and from this fact we must conclude that the smaller the number of elements in the construction of a furnace, the fewer the number of unreliable factors both in the construction and in the operation of the electric furnace. This conclusion deserves special attention when an electric furnace for making steel has to be chosen from the constantly-growing number of inventions, inasmuch as the chief constituent of steel, the element iron, is a substance which in its liquid phase has so great an affinity for those elemen'ts which are to be removed from the charge, that it is very difficult to comply with the following conditions: 1, to heat the refining-slag to the highest point of its chemical activity ; 2, to prevent the iron from entering the slag, or, where this cannot be done, to make it enter so that it finally appears in the end-product

Jan 1, 1911

By Heihachi Kamura

The reduction of iron oxide, such as Fe203, to iron in the blast furnace is performed principally by carbon monoxide, but partly by solid carbon by the two following reactions: Fe2O3 + 3CO = 2Fe 4- 3CO2 2Fe2O3 + 3C = 4Fe + 3CO2 It is known that reduction by carbon monoxide takes place at a much lower temperature than reduction by carbon and that the reducing action of earbon monoxide progresses to the inside of the ore in lump form by gaseous diffusion. In the reduction by carbon, however, the reducing action takes place only at the contact surface of the ore and carbon, so that the more complete the reduction by carbon monoxide, the more efficient is the operation. However, the reduction does not progress as shown in the foregoing equation, because carbon dioxide acts oxidizingly on the metallic iron to such a degree that when the gaseous composition reaches a certain proportion of carbon dioxide to carbon monoxide, the reduction practically stops, even though the gases are moving slowly through the heated ore. The proportions of carbon monoxide and carbon dioxide in the gas depend on the kind of iron oxide and the temperature of reduction, also on the duration of time in the reaction. The longer the time of the reaction, the higher the proportion of carbon dioxide obtained in the gas, but finally it will attain to a condition of equilibrium. Chemical Equilibrium of Iron, Oxygen, and Carbon Investigations concerning the equilibrium between iron, oxygen, and carbon have been carried out by E. Baur and A. Glaessner,1 who deter-

Jan 1, 1925

By Edgar Bain

SUMMARY THE results of an enquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration 'are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research Laboratories. All the compositions studied contained carbon in amount comparable to commercial alloys.

Jan 3, 1927

By Harold V. Pearce

The plant of the Boston and Colorado Smelting Company, at Argo, Colo., has not received special notice in technical or scientific publications for some time past. Dr. Peters1 described the development of the reverberatory furnace used at Argo, but he dealt almost exclusively with the increase in size and the corresponding gain in capacity. Since the time of his description the changed conditions hare led to a modification of the

Jan 1, 1906

The figures given here were received through the courtesy of the Bataafsche Petroleum Maatschappij and the Standard-Vacuum. There is an increase in production for the year of approximately 4½ million barrels. In November the average production indicated that during the year 1935 the total production would probably exceed 50 rnillion barrels. To maintain this production, only 106 wells were drilled during the year, mainly in South Sumatra.

Jan 1, 1935

By Robert H. Richards

(Read at the Amenia Meeting, October, 1877.) DURING the summer of 1870, I had an opportunity to visit the laboratory of the late David Forbes, Esq., in London, and was much interested in a labor-saving device which lie had attached to his agate mortar. The mortar was placed in the centre of a small table, and about ten inches to the right of the mortar, a post, perhaps two

Jan 1, 1878

By A. W. Ashbrook

From both economic and environmental aspects, the loss of organic materials from a solvent extraction process is of major concern. A decade ago perhaps the only consideration given to solvent loss was economic in nature. Today, the environmental -.and hygiene - impacts have to be seriously considered. In this section we shall deal essentially with the processing and economic aspects of solvent loss; the environmental aspects are discussed in a later section.

Jan 1, 1978

By D. Brabec

Previous studies have demonstrated the possibility of using aqua regia-extractable copper and zinc in plutonic rocks in exploration geochemistry. The present investigation compares this method of extraction with hydrofluoric-perchloric acid attack and bisulfate fusion in terms of precision and discrimination between high and low concentrations. Statistical treatment of data shows that the overall performance of the aqua regia method compares very favorably with other methods of attack.

Jan 1, 1972

By Desmond Y. M. Lee

Computerized preventive maintenance has been a long sought goal in many industries. People have firmly believed that proper implementation of such a system can result in tremendous saving of money. However, the preventive part has always been left out without realizing it due to the inflexibility of coping with environmental changes. With this in mind, the Iron Ore Company of Canada has developed a computerized system which schedules maintenance jobs preventively.

Jan 1, 1977

By Ta M. Li

This article draws freely on the experiences of the engineering and operating staff of P.T. Inco and its parent firm Inco Ltd. In addition, information was derived from papers presented during the recent International Laterite Symposium, held in conjunction with the 1979 AIME Annual Meeting, New Orleans, La., February 19-21. The author wishes to acknowledge all contributors and, in particular, Roy Aitken, president and managing director, P. T. Inco.

Jan 7, 1979

By H. W. Paxton, C. C. Busby

IT has been shown previously' that strain aging can markedly improve the tensile properties of low carbon martensites, especially the yield-tensile ratio, without seriously affecting the ductility. In view of interest in high strength steels, an investigation has been made of the effect of strain aging following tension or rolling on the tensile properties of A1S1 4340 in an attempt to obtain a tensile

Jan 1, 1957

JAMES.E. HOWARD, ? Washington, D. C. (written. discussion ?).-It is a pleasure to participate in the discussion of a paper on the endurance of steel to repeated alternate stresses. For many purposes the prime and only function of the metal is to resist strains and stresses: stresses of long duration in one direction only; stresses that alternate between a maximum and a. minimum in' one direction; and stresses of different de-

Jan 4, 1919

By T. M. Gurr

The United States is the world's leading producer of phosphate rock. In 1975 according to the US Bureau of Mines' statistics, 44.3 million tonnes (48.8 million st) of phosphate rock were produced in the United States, 1 which is 40.6% of the world's production.2 The major phosphate producing areas of the United States are located in Fig. 1 and the production for 1975 is listed as follows:

Jan 6, 1979

By John C. Smock

The fire-clays of New Jersey belong in two geological ages, the cretaceous and quaternary, or post-tertiary. Three very small deposits of plastic clays have been discovered within the limits of the Archæan rocks. These are not refractory and of little importance, excepting in a geological consideration. They have resulted from a decomposition of the feldspars of the rock in situ, and they have been classified as inferior kaolins.

Jan 1, 1879

By James E. Mills

In the work of exploring certain gold-bearing gravels in the American Valley, Plumas Co., California, entrusted to my charge by Prof. A. Agassiz, of Cambridge, and Q. A. Shaw, Esq., of Boston, it became necessary to sink a shaft through loose materials containing in some layers large quantities of water, and I have been compelled to devise a new method which has proved successful and may be of service elsewhere.

Jan 1, 1885