Search Documents

By John D. Gill

The purpose of this paper is to invite attention away from the obvious. direct monetary costs of oil-field overdevelopment (as distinguished from "social costs") to a consideration of the role played by the exercise of freedom to create even allegedly excessive1 plant facilities in contributing to the maintenance of equilibrium in the wholc economy and in promoting material progress. The obvious and most commonly discussed effect of overdevelopment of oil fields is illustrated by the allegation that already the excessive development of the East Texas field has cost upward of $162,000,000;2 in other words, the drilling of 12,500 wells more than the number estimated as the requirement for economical recovery of the reserve has unnecessarily raised the total cost of development that amount. Many other illustrations of so-called excessive development of oil pools could be presented. Some of them, like Cushing, Powell and Long Beach, might be drawn from the era antedating widespread discussion in the trade of such matters as optimum well spacing, reservoir energy, the conservation rate of depletion of reserves, etc. Numerous other cases can he found in the records of the current era, which began with the introduction of rationalized restriction of production. Besides East Texas, there may be mentioned Oklahoma City, Centralia and. more recently, the town-lot development of Bloomingdale, Michigan.

Jan 1, 1940

By D. G. Brubaker

IN the history of geophysical exploration by the electromagnetic method many procedures and types of equipment have been used. Source arrangements for surveying on the ground have included long wires grounded at both ends, large loops laid on the ground, small horizontal loops, and vertical loops of moderate to small sizes. Receivers have ranged from simple direction-finding coils to combinations of coils and a bridge circuit to measure quantities related to both amplitude and phase of the received signal. Primary considerations in choosing a survey method are effectiveness, speed, and economy. In work on the ground in which locating and out- lining conducting bodies is the objective, methods using a vertical coil and a simple direction-finder have been found the most satisfactory. Mason1 and his associates applied such a method by setting up a vertical source loop, fed with low frequency alternating current by an engine-generator set. With a direction-finding receiver they surveyed lines along the ground in the plane of the loop, taking measurements at each station of the azimuth and inclination of the magnetic field direction. Deviations of this direction from the normal direction, that is, from horizontal and perpendicular to the traverse line, indicated a conducting body. Recent advances in design of light-weight generating equipment have encouraged using this and similar methods.

Jan 7, 1957

By H. R. Hanley

ONE of the most important contributions to the art of electrolytic zinc production-has been the aluminum cathode. This has been used in all major production: since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experi-menting on the extraction of-zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent-No. 20073. The reason for this dominant position of aluminum as cathode mate-rial in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as arc tine copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a .few hours of deposition, and thus special arrangements must be made to compensate for this abnormality.

Jan 1, 1938

By John Gill

THE purpose of this paper is to invite attention away from the obvious, direct monetary costs of oil-field overdevelopment (as dis-tinguished from "social costs") to a consideration of the role played by the exercise of freedom to create even allegedly excessive1 plant facilities in contributing to the maintenance of equilibrium in the whole economy and in promoting material progress. The obvious and most commonly discussed effect of overdevelop-ment of oil fields is illustrated by the allegation that already the excessive development of the East Texas field has cost upward of $162,000,000;2 in other words, the drilling of 12,500 wells more than the number esti-mated as the requirement for economical recovery of the reserve has unnecessarily raised the total cost of development that amount. Many other illustrations of so-called excessive development of oil pools could be presented. Some of them, like Cushing, Powell and Long Beach, might be drawn from the era antedating widespread discussion in the trade of such matters as optimum well spacing, reservoir energy, the conservation rate of depletion of reserves, etc. Numerous other cases can be found in the records of the current era, which began with the introduction of rationalized restriction of production. Besides East Texas, there may be mentioned Oklahoma City, Centralia and, more recently, the town-lot development of Bloomingdale, Michigan.

Jan 1, 1939

By E. M. Wise

MANY of the platinum metal alloys are hot-forged in the early stages of reduction from ingot and substantial quantities of platinum alloys are commercially employed at very high temperatures in ammonia oxidation units, orifices for forming glass rods and fibers and as cathodes in long-life thermionic amplifiers. They are used also for electrical heating resistors, safety blowout disks, thermocouples and crucibles. The tensile prop-erties at elevated temperatures are important in many of these situations but data on the subject are limited. Creep data also are important, but will not be covered at this time. SCOPE AND CONCLUSIONS Tensile tests were carried out at room temperature and elevated temperatures up to 1100° C. on previously well annealed samples of platinum, palladium and several of their important alloys with composi-tions shown in Table 1. The results are presented graphically in Figs. 1 to 4. The tensile strengths of platinum and the platinum-base alloys (with the exception of the 10 per cent rhodium-platinum alloy) at 1100° C. are from 16.6 to 18.8 per cent of the strengths of the same alloys (well annealed) at room temperature. The strength ratio of the 10 per cent rhodium-platinum alloy is 22.3 per cent, which is appreciably higher than that of the other materials tested.

Jan 1, 1938

By J. D. Corbett

Mining geophysics in 1967 continued to expand with greater application in the exploration and development of mineral deposits. Moreover, geophysical activity increased without the particular emphasis of a Pine Point or Timmins discovery to spur interest. This trend is expected to continue through 1968 as geophysics more and more becomes an integral part of a mineral exploration program. This past year saw the "little black box" of the old-fashioned "doodlebugger" pushed further into the background, replaced by increasingly sensitive equipment of sophisticated design. The trend also is away from the one man geophysical operation wherein the same individual is responsible for the development, design and operation of the field gear, the planning and execution of a survey and analyzing and interpreting the data. In today's technology a staff of specialists, electronics engineers, mathematicians, physicists-to name but a few- are required to back up the exploration geophysicist in the development of new methods and techniques, in the reduction of the voluminous amount of field data and in the interpretation of the anomalies which can be enhanced by various high-speed computer techniques. Obviously a full back-up staff of these varied abilities is impractical to most exploration companies. However, the equivalent function is provided to the lone staff geophysicist by the many competent geophysical contractors and individual consultants.

Jan 2, 1968

By Woo-Zin Choi, Ting Chuen Pong, Roe-Hoan Yoon, James R. Craig, Robert M. Haralick

Detailed analysis by conventional techniques and by the General Image Processing System (GIPSY) has revealed that the conmunution of base metal-containing, complex, fine-grained sulfide ores results in the selective concentration of some ore minerals as a function of size fraction. The ores studied are massive, metamorphically recrystallized, pyrrhotite-rich masses with 10-30 percent pyrite and several percent each of sphalerite, chalcopyrite, and magnetite; gangue minerals - amphibole, mica, and quartz - constitute approximately 10 percent of the ore mass. Examination of samples from laboratory grinding experiments, - from +35 to -250 mesh - produced by both Impact and attrition grinding, reveals that there are significant differences in the mineralogical content of the various size fractions. No single fraction is representative of the bulk mineralogy of the sample. Pyrite is highly enriched in coarser fractions, whereas chalcopyrite, sphalerite, magnetite, and gangue minerals are concentrated in the finer size fractions. Concentration of the ore minerals in the finer fractions is attributed to their common presence as interstitial, grains along the grain boundaries of the more dominant pyrrhotite and pyrite. As such, they tend to be somewhat preferentially liberated as small fragments during the initial stages of crushing and grinding. The relatively coarse-grained pyrite, up to 1 cm cubes, is brittle and readily fractures into coarse fragments which are seen in larger size fractions.

Jan 1, 1984

By Walter Weeks

LITTLE study has been made of the pressure changes and energy losses that take place when an air current is divided into splits which subse-quently unite. The discussion and the experiments that are described in this paper deal with the division of an air current into square splits of equal size, the area of each of the splits at the downstream junction being one-half the area of the main duct. APPARATUS AND SYMBOLS The duct system shown in Fig. 1 was built of Y4-in. redwood and made as smooth as possible.The section of the top over the splits and the zone of mixing was of plate glass to permit observation of the stream lines. FIG. 1-DUCT SYSTEM. Static pressures were measured by means of pinhole tubes and a precise inclined manometer. Measurements of rates of flow were .made by determining the drop in pressure through concentric square orifices in the splits. The air was supplied by a fan operated by a direct-current motor that received its current from a motor generator set. Delicate rheostats in the armature. of the motor. made possible the perfect control of the fan speed, which was indicated on an electrical tachometer. Vanes to straighten the. flow were placed at the head of the main duct.

Jan 1, 1933

By Bernard Kopelman, C. C. Gregg

THE reduction of tungstic oxide to tungsten metal powder by hydrogen is a process by which one might expect the resultant metal powder to be porous. In- [ ] deed, sponge iron, prepared by reduction of the oxide in a reducing gas, is generally accepted as quite porous, with pores large enough to be seen readily under the optical microscope at relatively low magnifications. However, any pores that may exist in tungsten metal powder are not resolved by the optical microscope, and apparently, not even by the electron microscope. Fig I shows commercial tungsten powder magnified at 10,000X by the electron microscope,1 both etched and unetched. In an earlier paper by one of the authors,2 the existence of pores in tungsten powder [ ] was required to explain adequately the particle size changes occurring during the reduction of tungstic oxide. The inability to detect these pores under the electron microscope at 10,000 X implies that these pores are of a size of 100 A units or less. (This in itself is by no means proof that pores above 100 A would not exist, since polishing effects on the specimen might smear up holes of such small magnitude). If, then, these pores are less than 100 A, and of the order of molecular size, then the density of the metal powder should be

Jan 1, 1948

By J. Stringer, I. W. Edington, C. R. Rarey

THE geometrical interpretation of transmission electron micrographs of hcp metals is more complicated than the equivalent interpretation of cubic metal for two reasons: firstly, prominent zone axes are not in general normal to prominent planes, so that a simple diffraction pattern often corresponds to a nonra-tional foil plane; and secondly, the Miller-Bravais sys-tem of indexing directions is not easy to visualize. In this, the indexing is referred to the Bravais four-axis system, and the direction is labeled [hkil], chosen so that and I are shown in Fig. 1. Some geometrical relationships useful for the interpretation of transmission micrographs have been calculated and are tabulated below: 6) Direction of the intersection of two planes; this is easily calculated by applying Condition 4 to both planes: a direction that lies in both planes is clearly their direction of intersection. Some of the above expressions have also recently been given by Otte and Crocker;' Expression 5 is of course in most standard crystallographic texts. It is generally considered easier and quicker to use graphical methods for the interpretation of electron micrographs than analytical methods. For this purpose, it is most convenient to use a "double stereo-gram" in which both the poles alzd the rational directions are plotted. It is, of course, necessary to orient

Jan 1, 1967

By John S. Brown

IN 1925 the writer undertook a detailed statistical study of all producing areas in the Joplin district as a basis for evaluating programs and measuring objectives. For this purpose, the published figures in the yearly volumes of Mineral Resources were used, supplemented for earlier years by publications of the Missouri Geological Survey and other local and less official sources. When all else failed, the available data were projected backward to hazard a reasonable guess as to the unrecorded early output of important areas. Fortunately, the proportion of such prehistory production is not a large factor in any of the totals. These results were used during the next few years to measure the relative importance of various producing areas and to predict the peak period of development of the all-important Picher field. For the purpose of this review, the charts have been completed to the end of 1950. During World War 11, the U. S. Bureau of Mines became interested in a similar study and issued comprehensive statistical tabulations of data up to 1945 ( Info. Circular 7383), which have been checked against the figures used herein. This tabulation, however, does not include all the earlier data used by the writer nor does it offer any estimates of the wholly unrecorded era in the beginnings of the earlier camps.

Jan 9, 1951

By V. F. Malone

IRON ore reserves of Lone Star Steel Co. cover 56,000 acres in the north basin of the East Texas geosynclinal area near Daingerfield. Ore is almost wholly restricted to the Weches formation of middle Eocene Age. Its resistance to erosion has created the hilly topography of the East Texas area. The ore deposits, in the upper portion of the hills, are usually overlain with residual sand and clay overburden less than 15 ft thick. The ore formation consists of inter- bedded shallow ocean sediments ranging from pure greensand to fine-grained sands and clays containing a maximum of 70 pct limonite, or siderite, and varying from 2 to 100 ft thick. The iron in this ore originated as iron silicate or greensand in the ocean sediments, and the ore mineral siderite was formed when meteoric waters redeposited the iron under reducing conditions as a carbonate. With weathering and progressive erosion much of this siderite was later oxidized and altered to limonite - yellow to dark brown hydrous iron oxides formed into nodules up to 18 in., embedded in a sandy clay and weathered greensand matrix. Beneath the water table the siderite zone consists of interbedded shale and greensands with thin ledges and nodules of siderite. Lone Star Steel Co. has proven a 75-year supply of ore, and exploration of reserves and acquisition of new property is not complete.

Jan 5, 1957

By Thomas P. Meloy, Duane T. Eppler

The science of particle shape analysis has expanded rapidly in the decade since precise numerical-statistical techniques were developed for use in characterizing the shape of closed forms. Use of Fourier descriptors permits shape to be quantified to whatever degree of precision is required. With this technique, particles and particle systems can be compared either on the basis of shape characteristics displayed by individual particles, or on the basis of aggregate shape characteristics representative of large samples of particles. Shape characterization work completed to date has shown that the physical characteristics of particle systems (porosity, permeability, strength, mechanical stability, chemical reactivity, and flow characteristics (viscosity)) are related directly to particle shape. Furthermore, it has been shown that particle shape is a function of chemical composition, process of formation, and post-formational history of the particle. In this light, particle shape analysis has potential applicability to a host of engineering and industrial problems encountered in processing particulate material. It can be used to optimize the efficiency of separation processes and particle feed systems, to trace particle pathways through processing systems, and to monitor the operation of specific processes, the wear of critical machine parts, and the quality of end products in processing systems. In this paper we discuss these specific applications of shape characterization to particle processing.

Jan 1, 1980

By George L. Heath

It may at first appear doubtful that any further ideas can now come from such a well-trodden soil, when we consider that the ground of the subject has been so thoroughly gone over in many of its phases and that observations have been recorded in technical journals, ever since the days when Luckow and his cotemporaries brought the electrolytic deposition of pure copper to the position of an exact scientific method. Certain facts, however, which seem worthy of note, have come under the writer's observation during an extended use of the method in a large refinery, involving frequent tests of refined Lake and electrolytic copper, and thousands of assays of native copper concentrates and tailings. This work has required a careful study of the conditions suited to the assay of refined copper, and of ores and tailings— conditions which must be varied for each particular case to secure the best results. Especially is this true when we come to the exact determination of pure copper in the high-grade refined metal of the present day. Very slight traces of impurities (especially tellurium, selenium, bismuth, tin, arsenic and antimony) seriously injure the properties of copper, notably its electrical conductivity. The increasing demands of electrical science and construction lead to the conclusion that the analysis of all high-grade American coppers, at least, has become, and must be in future (in or-

Jan 1, 1898

By R. F. Pilgrim

A digital computer program to mathematically simulate the effect of limited changes in feed rate in the range of 80 to 95 tph on a plant-scale wet grinding circuit has been developed and tested. The circuit studied included an 8-ft-diam X 12-ft rod mill operating in open circuit and feeding two parallel 12-ft-diam x 10-ft pebble mills, each one operating in closed circuit with an 8 X 32-ft rake classifier. The simulation is an empirical one based on two sets of data collected manually from the operating circuit under what was said to be steady-state feed rates of 80 and 95 tph with all other operating variables also at steady state. The procedure is a combination of several published approaches to the modeling of grinding mills and classifiers and it is applicable to a wide range of circuits. The program permits the computing of the size distributions of all feeds and discharges of all grinding units and classifiers in the circuit for a specified feed rate. The data used in this report for demonstrating the program are unsatisfactory since the circuit was not operating under steady-state conditions when it was sampled. Consequently the circuit model parameters could not be accurately estimated. The predictive power would be greatly improved if new data were obtained under true steady-state conditions.

Jan 1, 1973

Dr. F. W. C. Schniewind, New York, N. Y.:—Mr. Vogel speaks of briquetting the flue-dust by means of lime. I learned recently in Europe of a process employed with considerable success at one of the blast-furnaces, where blast-furnace cinder is used with lime. The lime and cinder are mixed with the flue-dust, and exposed to superheated steam, which converts the blast-furnace cinder into cement. Briquettes are then formed in the usual way. Mr. Vogel :—The process referred to is the " Scoria process," which has not been in use for some time past. For that reason, I did not mention it. Prof. Arthur L. Walker, New York, N. Y.:—I would ask the commercial name for magnesium chloride, and where it can be obtained ? Mr. VoGel :—I mentioned magnesium chloride, because it has been used abroad to a large extent. In Germany it is obtained as a by-product in the manufacture of potash-salts; in the United States we have been using chloride of lime, which is cheaper. Otto Sussman, New York, N. Y.:—What is the cost of this process ? Mr. Vogel :—The cost is exceedingly low. I can give you the figures from abroad, but not for the United States, because the system has not -yet been used here commercially to

Jan 1, 1913

By Chi-shing Wang

The late Professor P. B. Bucky of Columbia University introduced the principles and techniques of barodynamic experimentation in early 1931 by the application of centrifugal loading to achieve dynamic similitude between models and prototypes of mine structures.1 Later, he and his associates introduced the combined experimental technique of photo- elasticity and the centrifuge to determine the stress distribution in civil engineering structures and mine workings by the use of transparent bakelite models.2,3 The photostress technique, also known as the birefringent-coating method of photoelastic stress analysis, dates back to 1930, when Mesnager published its principles.4 Since then it has been widely applied to experimental stress analyses in many industries. A practical method of observing the dynamic behavior of opaque mine models, which are made of prototype materials, by means of a combination of the centrifugal and the photostress techniques is a new experimental approach under development at the Henry Krumb School of Mines, Columbia University.5 This paper summarizes the development of the barodynamic photostress technique and presents the information obtained from a recent series of experiments in the study of the behavior of rock beams loaded by their own weight. THEORETICAL BACKGROUND Theory of Pure Bending In the general theory of strength of materials, the flexure stress at any point in a beam of any type of cross section which has a longitudinal

Jan 1, 1968

By F. W. Metzger

INTRODUCTION Coal quality control in mining and mine planning has always been important and has become even more essential in recent years due to environmental considerations. The primary consumers of the sub-bituminous coals found in the Powder River Basin are electric utilities that require low sulfur coals to meet government air quality regulations. Electric generating plants are designed to burn coal of a specific quality, and the supplier of that coal must be able to guarantee shipments within specified quality tolerances. Over the past several years, Exxon Coal USA and, more recently, The Carter Mining Company, a division of Exxon Coal USA, have established an evaluation and development program to accurately define the geology and quality of their coal properties. This requires an adequate drill hole density so that detailed correlations of the coal seam and the lithologic units, or benches, within the coal seam can be made. These units are recognizable in the core and also on geophysical logs. Like any systematic approach, geologic modeling has been refined and improved through new technologies. Today, coal seam properties are mapped using computer applications. Rapid access and manipulation of these data allow for optimization of mining efforts. This presentation will demonstrate how a detailed mapping program can be important in both pre-mine development and in-pit quality control.

Jan 1, 1983

By David Swan

No mystery shrouds the discovery of chromium. The indefatigable French chemist Vauquelin, in reporting his discovery of this chemical element to 1'Institut National in 1798, concluded his discourse with the statement: "I place before the eyes of the Institute a small quantity of chromium and several of its most re- markable combinations." Working with the so-called "red lead of Siberia, Vauquelin not only prepared numerous chemical compounds of the new metal, but he reduced the oxide to the metallic state. These chemical compounds possessed a variety of remarkably distinctive colors; so, acceding to suggestion, Vauquelin named the new element chrome (chromium), a derivative of the Greek word chroma, meaning color. Siberian "red lead" (crocoite) was not plentiful; however, it was not long before Vauquelin's prediction was realized that the chemical compounds of chromium would become useful in the arts when sources of chromium became more readily available. Although chrome-iron ore (chromite) became obtainable in France, the United States and elsewhere during the early part of the nineteenth century, it is interesting to note that from 1828 to about 1860, Maryland, Pennsylvania, and others of the eastern United States furnished almost the entire chrome-ore requirements of the world. Several countries each in turn have since dominated for certain periods the supply of chromite. In recent years, the largest tonnages have come

Jan 1, 1953

While mining silver at Butte in 1882, Marcus Daly is reputed to have told his partners in The Anaconda Silver Mining Co., "It looks rather gloomy. The vein is running into copper." Recently, The Anaconda Co. authorized an $11 million expenditure to be made over the next five years to ensure their "running into copper" at deep levels for many more years. The new development program is designed to permit both deeper and more widespread selective mining in "the richest hill on earth" by means of additional shaft-sinking, reactivating closed mines, and establishing new haulageways and centralized hoisting facilities. Historically a deep level selective mining camp, Butte will now continue its uncommon use of three main types of mining methods at one camp-selective mining, block caving, and open pit mining. It was thought by some people that the construction of the Kelley shaft and the subsequent beginning of block caving operations in 1952-outgrowth of the Greater Butte Project-signaled the end of stope mining of high-grade ores at depth. This feeling became more pronounced when, in 1957, the Berkeley open pit commenced operations. During recent years, the tonnage of ore mined selectively underground has decreased, but the new program will maintain the position of selective underground mining in the overall picture of the Butte operations for many years to come.

Jan 7, 1960