Search Documents

By Mark S. Childs

FRIEDENSVILLE orebody in Lehigh County, Pennsylvania, lies in the south central part of the USGS Allentown Quadrangle. Physiographically the area is located in a small reentrant-known as Saucon Valley-of the Great Valley Province into the Reading Prong of the New England uplift. Saucon Valley itself is an oval-shaped lowland eight miles long and four miles wide, surrounded by ridges except where connected with the Great Valley through a breach in the rim known as Saucon Gap. These ridges, composed of Pre-Cambrian metamorphic rocks and Cambrian quartzites, rise some 500 ft above the valley floor. They are continuous with the New Jersey Highlands. The valley lowland is immediately underlain by lower Paleozoic dolomites and limestones. This area is one of low relief having a swing of approximately 100 ft, with an average elevation of 375 ft above sea level. The entire valley, which has a water shed of about 58 sq miles, is drained by Saucon Creek. This unit flows in a northeasterly direction to the Saucon Gap, where it discharges into the Lehigh River.

Jan 1, 1957

By E. Morgan Massey

Located in virgin coal acreage near Gilbert, W. Va., Massey Coal Mining Co.'s Ben Creek No. 2 mine afforded the company's engineers the opportunity of designing and laying out the entire mining operation from the mine faces to the railroading loading site. However, the topography of this region posed difficult problems in haulage of coal for, in this extremely rugged terrain the uppermost coal seams lay in the mountain-top ridges, approximately 1400 ft above the valley floor. The decision for mining equipment naturally leaned to the new high-capacity continuous miners where seam conditions permitted: otherwise, to the new super-high capacity conventional cutting and loading machines. Since the coal seams lay in ridges and points of considerable outcropping, the decision was to keep the transportation on the surface and mine the coal with multiple entries into the outcrop. This way, the major problems of underground haulage, drainage, and ventilation are eliminated, and the opportunity to take advantage of a-c underground power becomes a much simpler proposition.

Jan 10, 1960

By W. P. Blake

The mining district and the town of Tombstone are situated in Cochise County, Arizona Territory, at the northwest end of the Mule Pass range of mountains, in longitude 110°, and latitude about 31 40' N,, upon the right bank of the San Pedro River, from which the town is distant 9 miles east.. It is also 24 miles south of Benson station on the Southern Pacific Railroad of Arizona, and about 40 miles north of the Mexican line. Its altitude above the sen is 4600 feet. The Dragoon Mountains rise across a valley to the northeast, and the Huachuca Range similarly upon the southwest. The country is open, without timber, and the surface, where the mines are opened, is in general gently rolling, and accessible to wagons by. natural roads. The first locations were made in the pear 1878 by the Scheffelin brothers and Richard Gird, the latter being well known among the pioneers of Arizona as a surveyor and miner, who contributed largely to our knowledge of the geography of the Territory in early days,

Jan 1, 1882

By J. S. Jacobi

Treating copper ores by heap-leaching and similar hydrometallurgical means is a time-honored practice, which was well known even in the 19th century. Later the method lost ground to better ore dressing processes, particularly selective. flotation. More recently there has been a distinct reversion to leaching techniques, particularly for scavenging operations in old mining stopes, in connection with LPF systems, irrigation of tailings dumps and similar situations. These hydrometallurgical techniques will gain further ground because processing is simple and permits better extraction of copper, particularly from low-grade or partly oxidized ores. In the lixiviation of primary ores at some major operations, copper-bearing liquors may undergo re-circulation in heap-leaching arrangements or the ores may be subjected to systematic percolation treatment. The liquors resulting from this source usually are quite strong (above 10 gpl copper) and copper would normally be reclaimed by electrowinning or cementation. These processes fall out- side the scope of this paper which is concerned with recovery of copper from weak 1iquor.s containing from 0.1 to about 3 gpl copper.

Jan 9, 1963

By James Elton

THIS paper covers, besides laboratory work, a study of actual operation at the Washoe Smelter over a considerable period of time, together with the results of a visit to the Midvale plant of the United States Smelting- & Refining Co., near Salt Lake. For the latter privilege, as well as permission to publish the resulting data herein given, I am indebted to George W. Heintz, General Manager of the Midvale plant, and here take pleasure in. expressing my appreciation for the many courtesies extended to me by Mr. Heintz and members of the technical staff at the smelter. Almost all of the world's supply of arsenic is recovered as a by-product in the smelting of other metals. It is seen on the market in various forms, the most common being arsenic trioxide, the ? white arsenic " of commerce, which is sold as a heavy white powder, or in white, glassy, translucent masses. The trioxide is used in the manufacture of pigment, glass, and insecticides. About 50 per cent. of the domestic consumption is supplied by imports.

Jan 8, 1913

By J. M. Johns

INTRODUCTION The Climax Mine is located on the continen¬tal divide, on Fremont Pass, about 145 Km south west of Denver, Colorado. Molybdenum, along with the by products, tungsten, tin, and pyrite are produced from both the open pit and under¬ground operations. The underground operation utilizes a panel caving mining system, and produces in excess of 27,000 mt per day. In the mid 1930's, the Climax mine began changing from a grizzly level layout to the slusher drift system which is still in use to¬ day. Over the years, the slusher drift layout has been refined to correct, improve, and sim¬plify minor operational problems. In common with most older hardrock mines, the development equipment used at Climax was the standard rail mounted, pneumatic mining machinery. This type of equipment remained in use, at least to some degree, until about four years ago. For production, 112 Kw electric slushers were used, while mine traffic was rail with trolley locomotives. Beginning about ten years ago, Climax began

Jan 1, 1981

By Vincent Carlsson

A comprehensive investigation has been undertaken to clarify how pellets are affected by alkali circulating in the blast furnace. The investigation has been performed with acid and basic pellets in a special furnace. Experiments were carried out to ascertain the influence of potassium on swelling and reducibility when added at different stages of reduction. After that, the significance of the quantity of potassium added in the hematite stage was studied. A parallel experiment with sodium as the alkali component was also con- ducted. Besides these vaporization experiments the effect of alkali on softening and reduction characteristics at high temperatures was investigated. The results showed that alkali always increases swelling, especially when added in the hematite stage. The addition of alkali increases reducibility of acid pellets during reduction from wustite to 70 % reduction. The softening temperature is significantly lowered by the addition of alkali and is, in any case, lower for acid pellets than for basic pellets. The microscopic studies showed that alkali ferrites can be formed irrespective of the influence of alkali on the slag phase.

Jan 1, 1977

By W. H. Emerson

In the summer of 1894, a specimen of corundum from Acworth, Ga., which mas reputed to be of markedly inferior quality for the manufacture of corundum-wheels, was received by the Geological Survey of Georgia, with the request that it be analyzed, in order to ascertain whether this inferiority was associated with any peculiarity of composition. In its appearance there was nothing uncommon, though it seemed to be rather easily scratched with a knife, while, at the same time, it scratched agate easily. An analysis gave the following results: Alumina, 94.58; silica, 1.77; magnetic oxide of iron, 0.69; calcium oxide, 0.44; and water, 2.51 per cent. There is nothing unusual in this composition, except the amount of water, which is usually, in southern corundum at least, from 0.3 to about 1 per cent. Concerning this corundum, the Mineral Resources of the United States, 1893, pp. 676 and 677, Bays: "It is supposed that this variety of corundum contains a little water, as it is

Jan 1, 1900

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,000. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service.

Jan 1, 1946

By J. C. Bayles

An obstacle to the more careful and satisfactory study of metals has been the difficulty in harmonizing the results of chemical and physical tests. These give us records of observations made from different and often widely separate points of view, and while it is true that they furnish bases for more or less accurate triangulations into the realm of speculation, it is doubtful if, with only the laboratory and the testing machine, our investigations would not move in parallel lines, leaving between them an unexplored field in which must probably be sought the information which shall connect the results of chemical and physical tests, and give to both a practical value which neither has yet been found to possess. The use of the microscope in the study of metals is not a new thing, but it is only lately that it has begun to attract the attention it merits or to show results of tangible value to the metallurgist. Among recent valuable contributions to the literature of this subject, I have been especially interested in the work of Mr. A. Martens, of

Jan 1, 1883

By Robert R. French

Beneficiation of low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, and electric and magnetic properties of the ore and gangue are similar, the possibility of separation by color, reflectivity, or fluorescence offers hope for the utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Tests performed late in 1966 and reported herein are the result of continued interest in the dry beneficiation of gypsum and the development of higher capacity color-sorting machines. These tests should be considered only as an indication of the efficiency of the process and only with respect to the low-grade, untreated ore tested. Although most of the ore mined in Martin County, Ind., is of acceptable quality, a few thin carbonate strata and irregular nodules of dolomite and limestone are present within the main evaporite bed (Fig. 1).

Jan 1, 1969

By L. Messulam, A. S. Appleton

Iwo major studies of the Fe-Cr-C system are available in the literature. The earlier one of Kinzel and crafts' forms the basis for the data most commonly quoted in works of reference (e.g., Metnls HandDook) though the later work of Bungardt el a1.' is more extensive and amenable to analysis in terms of isothermal sections and so forth. However it is evident from examination of either of these studies that the delination of phase boundaries on the basis of the data obtained can only be very approximate. Indeed in several instances the data are so inconclusive that this delineation is a matter of opinion. This note is to report an analysis of experimentally determined carbon activity data in this system, which, originally intended as a means of checking the self-consistency of the data for a number of alloys, enables some conclusions to be drawn concerning the 10503C isothermal section of the iron-rich corner of the system as deducible from the data of Bungardt

Jan 1, 1967

By James J. Bailey

Percussive drills have been in commercial use for many decades. Until relatively recently there was little serious effort to analyze the stresses in such devices in any detail. Within the last few years such analyses have been developed and have been reported by a number of authors.1-4 We present here an investigation of the impact systems of a family of conventional down-hole drills with optimization the objective. We have assumed that maximum drilling speed was the quality most desired and that this was to be achieved within conventional practice. In fact the methods that are demonstrated in principle below can readily be adapted to other percussive devices, whether conventional or not, and to other constraints. SOME PERFORMANCE PARAMETERS FOR PERCUSSIVE DRILLS Consider a percussive drill with an air motor operating with the following parameters: p-supply air pressure a-effective piston area W-piston mass S-piston stroke If we consider a simple (constant pressure) cycle, the following relationships can be derived. The blow frequency [N~ pa lie WS 377]

Jan 1, 1968

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which. the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,000. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation', the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service.

Jan 1, 1952

By David White

THE environmental conditions under which coals are deposited are revealed by the stratigraphy of the coal basins and coal beds and by the details of the structure and the physical constitution of the coals themselves. THE LAND SURFACE Generally Low Relief or Base Level In the Paleozoic coal fields, which have longest been worked, are most important, and are best known, we find relations, in general, as follows A post-Mississippian uplift with, in most cases, very moderate deformation, followed by erosion by which the uplifted regions, especially the bolder of the new topography, were largely worn down, while the older and less deformed regions were more or less extensively base leveled. Base leveling of most of the region continued as the deposition of coal measures proceeded. Consequently, in most coal fields the Pennsylvanian, or upper Carboniferous, lies unconformably on the Mississippian or on older formations. There are but few regions in which sedimentation is seen to have been apparently continuous from the Mississippian into the Pennsylvanian ("Coal Measures").

Jan 1, 1925

By Shosei Serata, Bruce Gardner

A system of three new field instruments has been developed to measure, in situ, the three basic classes of geomechanical parameters: material properties, stress state, and creep deformation. The significance of this development is that it represents a successful adaptation of recent computer technology to underground rock mechanics work, opening up new possibilities in underground mining methods. The system was developed to meet the application requirements of the stress control method of mining, a method which is based on the actual geomechanical conditions of the underground, rather than upon conventional linear-elastic, idealizations of ground conditions. These instruments enable in situ measurement not only of elastic, but also post-elastic, yielding, and failure conditions of geological materials, establishing the stress control method on a truly scientific foundation. In order to evaluate the present status of this field instrumentation system, case examples of underground mine openings designed with the stress control method are reviewed and analyzed, in terms of the effectiveness of the three instruments for informing and guiding the site-specific application of stress control design.

Jan 1, 1984

THE SOUTHWEST MINING SECTION of the National Safety. Council held a well attended two-day conference at Globe, Ariz., March 19 and 20; followed by two days of mine-rescue maneuvers at the Old Dominion mine in cooperation with the Globe-Miami District Mine Rescue and First Aid Association and the U. S. Bureau of Mines. C. L. Colburn of the Bureau had general charge of the arrangements and was chairman of the conference. All sessions were held in the Old Dominion Library. The program of papers was as follows: MINE FIRE PREVENTION AND FIGHTING What to do in Case of a Mine Fire. / Chas. A. Mitke, Consulting Mining Engineer, Bisbee, Ariz. Gunnite as a Fire Preventative. W. C. Browning, General Manager, Magma Copper Co., Superior, Ariz. Chemical Engineer's Part in Fire Fighting. Dr. L. H. Duschak, Consulting Chemical Engineer, San Francisco, Cal. Mine Fire Drills. A. C. Stoddard, Chief Mining Engineer, Inspiration Consolidated Copper Co., Inspiration, Ariz. Notes on the Installation of Fire Fighting Equipment in Mines. Benjamin F. Tillson, Assistant Superintendent, New Jersey Zinc Co., Franklin, N. J.

Jan 5, 1923

By Chauncey Berrien

THE Hawkesworth detachable drill steel shank and bit were invented by A. L. Hawkesworth; while he was a mechanical foreman for the Anaconda Copper Mining Co., at Butte, Mont. Mr. Hawkesworth died on June 16, 1925, at the time that his invention was practically a proved success. The first application for patents was made by him in November, 1918, and the bit is now being manufactured under patents issued in 1922 and 1923. The credit, for its development in the early stages belongs to A. L. Hawkesworth, Roy S. Alley, Harry A. Gallwey, E. J. Bowman and various officials of the Anaconda Copper Mining Co. Later improvements, manufacturing problems and the direct usage in the mines were originated and perfected by the mechanical department under C. D. Woodward, E. R. Borcherdt, head of the Rock Drill Equipment Department, Robert E. Kelly of the Mechanical Department, and various operating department heads of the Anaconda Copper Mining Co. The author wishes to acknowledge the assistance of these officials in the preparation of this paper.

Jan 1, 1930

By Charles J. Potter

There are many sources of energy available for consumption. Some available are solar, tide and wind. However, in terms of relatively large usage, only four principal sources are used for primary energy today. They are coal, oil, natural gas and water power. Such additional items as wood and nuclear energy, although supplying quantities of energy today, do not in the aggregate amount to any real significant quantity, but nuclear energy must be considered for future use. In addition, such a thing as gas from distillation of coal and oil is not considered primary energy. The principal markets for primary energy are the electric power utilities, space heating, industrial uses and transportation. The electric utility use of energy is primarily from coal, followed by natural gas and water power. Space heating is primarily a gas market, followed by oil and then coal. Space heating by electricity is only considered in the generation of electric power. Transportation's principal source of energy is oil. Coal has practically no market left in this field.

Jan 4, 1962

By C. F. Wang

Page I. Introduction............:.............. 395 Manchuria in General ....................... 395 Pen-hsi-hu............................ 397 Pen-hsi-hu Coal & Iron Co., Ltd................... 399 I1. organization........................... 400 III. Coal Deposit........................... 402 Location..............................402 Geology............................. 403 Coal Mining...........'.................. 404 Mining Methods........................407 Mining Cost.........................408 IV. Coal Washing Plant.......................408 V. Coking Plant..........................410 VI. Iron Deposit...........................413 Magnetite Belt.......................... 413 Origin of Deposit......................... 414 Iron Mining........................... 415 VII. Concentration Plant........................ 417 VIII. Briquetting Plant.......................... 418 IX. Blast-furnace Smelting...................... 418 iNTKODtrCTION Manchuria in General Manchuria. called the "Three Eastern Provinces" in Chinese. forms the northeastern corner of China and is bordered by Siberia on the north and northeast. and by Korea on the east. It is a land famous in Chinese annals as the place of origin of the Ching dynasty. and in more recent times it has bcen an arena for diplomatic maneuvering and commercial competition between the Russians. advancing from the north. and the Japanese from the southeast. It derives its name of "three eastern provinces" from the fact that it is divided into three provinces; Hei-

Jan 1, 1918