Search Documents

By Joseph W. Leonard, T. S. Spicer

INTRODUCTION Reasons for Thermal Drying The continuing increase in the percentage of minus %-inch coal produced as a result of the increased use of mechanical mining methods has, over the years, tended to shift considerable portions of the work of producing saleable coal to the fine coal cleaning section of the preparation plant. Because a given weight of fine coal will contain substantially greater surface area than an equivalent weight of coarse coal, it follows that, when subjected to wet cleaning processes, the fines will absorb and retain consider- ably more moisture than coarser fractions. Increased moisture pickup in the finer sizes complicates fine coal cleaning since beneficiation may not be limited to the removal of ash and sulfur but often must be expanded to include the additional step of thermal drying to remove excessive moisture. Thus, water which provides the medium for cleaning fine coal is in itself detrimental and, like ash and sulfur, reduces coal quality. Removal of surface moisture by drying is done for one or more of the following 1 reasons: (1) To avoid freezing difficulties and to facilitate handling during shipment, storage and transfer to the points of use; (2) to maintain high pulverizer capacity; (3) to reduce heat loss due to evaporation of surface moisture from the coal in the burning process, thus increasing heating efficiency; (4) to improve the quality of coal used for special purposes, such as in the production of coke, briquettes, and chemicals; (5) to decrease transportation costs; and (6) to facilitate dry coal-cleaning processes. Because benefits to coal transportation and utilization are the most common reasons for thermal drying, the following sections will examine these areas in greater detail. Benefits to Transportation Initial benefits from drying are the reduction of shipping costs from the mine to the point of utilization since more coal can be concentrated into a given weight of product when worthless moisture is removed. Non- combustible~ such as water and mineral matter in railroad shipments of coal are billed the same as coal at $3.32 per ton, according to the recent average costs. Savings of 10 to 20 dollars from drying on the shipment cost of each 50 to 60 tons of coal contained in a typical railroad car is common. Savings on coal shipments from individual mines which result from coal drying can be expressed in terms of hundreds of thousands of dollars and more each year. For example, a reduction of shipping charges of only 5 percent on one million tons per year would mean a savings of 166,000

Jan 1, 1968

Some Things We Don't Know about the Creep of Metals. By H. W. Gillett (T.P. 1087) Reduction of Iron Ores under Pressure by Hydrogen. By Michael Tenenbaum and T. L. Joseph (T.P. loll, with discussion) Induction Furnaces for Rotating Liquid Crucibles. By E. P. Barrett, W. F. Hol- bRook and C. E. Wood (T.P. 986, with discussion) Mechanism of Solidification and Segregation in a Low-carbon Rimming-steel Ingot,. By Anson Hayes and John Chipman (T.P. 988, with discussion) Solidification of Rimming-steel Ingots. By A. HultGRen and G. PhRagmen. (Contribution 112) Dendritic Structure of Some Alloy Steels. By Daniel .I. Martin and James L. Martin (T.P. 1066, with discussion) Occlusion and Evolution of Hydrogen by Pure Iron. By George A. Moore and Donald P. Smith (T.P. 1065, with discussion) Structure of Iron after Con~pression. Hy Charles S. Barrett (T.P. 977, with discussion) Structure of Iron after Drawing, Swaging, and Elongating in Tension. Ry Charles S. Barrett and L. H. LevensoN (T.P. 1038, with discussion) Magnetic Torque Studies of the Texture of Cold-rolled and of Recrystallized Iron-silicon Alloys. By Leo P. TaraSovJ(T.P. 1012, with discussion) Influence of Atmosphere and Pressure on Structure of Iron-carbon-silicon Alloys. By Alfred Boyles (T.P. 1046) Kinetics of the Decomposition of Austenite at Constant Temperature. By J. H. Austin and R. L. Rickett (T.P. 964, with discussion) Reaction Kinctics in Processes of Nucleation and Growth. By William A. Johnson and Robert F. Mehl (T.P. 1089, with discussion) Phase Changes in 3.5 Per Cent Nickel Steel in the Acl Region. By I. N. Bavarine (T.P. 1031, with discussion) Chromium in Structural Steel. By Walter Crafts (T.P. 1055) Surface Allotropic Transformation in Stainless Steel Induced by Polishing. By J. T. BuHwell and J. WUlff (T.P. 1032, with discussion) Nature of :Passivity in Stainless Steels and Other Alloys, I and 11. Ry H. H. Uhlig and John WUlff (T.P. 1050, with discussion) Thermal Expansion of Nickel-iron Alloys (Nickel from 30 to 70 Per Cent). Ry J. M. Lohr and Charles H. Hopkins (T.P. 987, with discussion) Low-temperature Transformation in Iron-nickel-cobalt Alloys. By L. L. Wy~Ian (T.P. 1013, with discussion) Fracture of Steels at Elevated Temperatures after Prolonged Loading. By R. H. Thielemann and E. R. Parker (T.P. 1034, with discussion)

Jan 1, 1939

Some Things We Don't Know about the Creep of Metals. By H. W. Gillett (T.P. 1087) Reduction of Iron Ores under Pressure by Hydrogen. By Michael Tenenbaum and T. L. Joseph (T.P. loll, with discussion) Induction Furnaces for Rotating Liquid Crucibles. By E. P. Barrett, W. F. Hol- bRook and C. E. Wood (T.P. 986, with discussion) Mechanism of Solidification and Segregation in a Low-carbon Rimming-steel Ingot,. By Anson Hayes and John Chipman (T.P. 988, with discussion) Solidification of Rimming-steel Ingots. By A. HultGRen and G. PhRagmen. (Contribution 112) Dendritic Structure of Some Alloy Steels. By Daniel .I. Martin and James L. Martin (T.P. 1066, with discussion) Occlusion and Evolution of Hydrogen by Pure Iron. By George A. Moore and Donald P. Smith (T.P. 1065, with discussion) Structure of Iron after Con~pression. Hy Charles S. Barrett (T.P. 977, with discussion) Structure of Iron after Drawing, Swaging, and Elongating in Tension. Ry Charles S. Barrett and L. H. LevensoN (T.P. 1038, with discussion) Magnetic Torque Studies of the Texture of Cold-rolled and of Recrystallized Iron-silicon Alloys. By Leo P. TaraSovJ(T.P. 1012, with discussion) Influence of Atmosphere and Pressure on Structure of Iron-carbon-silicon Alloys. By Alfred Boyles (T.P. 1046) Kinetics of the Decomposition of Austenite at Constant Temperature. By J. H. Austin and R. L. Rickett (T.P. 964, with discussion) Reaction Kinctics in Processes of Nucleation and Growth. By William A. Johnson and Robert F. Mehl (T.P. 1089, with discussion) Phase Changes in 3.5 Per Cent Nickel Steel in the Acl Region. By I. N. Bavarine (T.P. 1031, with discussion) Chromium in Structural Steel. By Walter Crafts (T.P. 1055) Surface Allotropic Transformation in Stainless Steel Induced by Polishing. By J. T. BuHwell and J. WUlff (T.P. 1032, with discussion) Nature of :Passivity in Stainless Steels and Other Alloys, I and 11. Ry H. H. Uhlig and John WUlff (T.P. 1050, with discussion) Thermal Expansion of Nickel-iron Alloys (Nickel from 30 to 70 Per Cent). Ry J. M. Lohr and Charles H. Hopkins (T.P. 987, with discussion) Low-temperature Transformation in Iron-nickel-cobalt Alloys. By L. L. Wy~Ian (T.P. 1013, with discussion) Fracture of Steels at Elevated Temperatures after Prolonged Loading. By R. H. Thielemann and E. R. Parker (T.P. 1034, with discussion)

Jan 1, 1939

By A. F. Frederickson

Rapid advances in any branch of science often follow the development of new instruments or techniques which permit the scientist a closer look at the material in which he is interested. With the development of the polariz¬ing microscope, modern petrology was born. The resolving power of the microscope, however, was not great enough to enable the geologist to dis¬tinguish or identify the material now known to be minerals which constitute the bulk of the rocks known as "clays" and laterites. The discovery of X-rays and the development of powder X-ray diffrac¬tion techniques provided the extra resolving power necessary to get "a closer look" at the minerals in the clays and laterites. These techniques are largely responsible for the great strides made in the past two decades in the identification of the clay, sesquioxide and hydroxide minerals. To obtain an X-ray diffraction. pattern of a mineral or rock is relatively a simple procedure, but to interpret this pattern in terms of crystal structure or min¬eral identity is quite another matter. It has taken the combined talents of physicists, physical and colloid chemists, mineralogists, and geologists to unravel the identity of some of the minerals in these complex rocks and, as this symposium will indicate, many more problems remain to be solved. To assist in the identification of these minerals, we have the ever-useful microscope, which, is supplemented by the development, only in the last ten years, of differential thermal techniques and the powerful and costly "eye" that enables us to see the shapes and sizes of extremely small particles -the electron microscope. To this array of equipment must be added such gadgets as supercentrifuges, spectrographs, and the apparatus necessary for chemical analytical work. Obviously, not only is it difficult for any one man to master all of the techniques to the point where he can do competent re¬search, but also few institutions are able to provide the high capital outlay for purchase and maintenance of suitable equipment. Here we clearly see that if this equipment is to help us solve our many problems, a close co¬operation of specialists from various institutions and industry is essential. This, however, is less than half the problem. If the geologist is going to learn to intelligently find, and the industrialist to intelligently and eco¬nomically exploit the materials that constitute a large part of the mineral wealth upon which our way of life is based, we must get a better insight into

Jan 1, 1952

THE Rocky MountainClub brought into the East the spirit of the West; the impulse to build, to develop, to accept unquestion-ingly the comradeship and help of any straight shooter who had it in him to accom-plish things and a will to work. That this was the spirit of the Club was due to its leaders. It was their spirit and they attracted around them men of the same stamp. Among those who made the Club what it was no one had larger in-low fluence than William Boyce Thompson, the vice-president and chief of financial staff. It was characteristic of him that the same financial genius that was employed in building up Nevada Consolidated, In-spiration, Magma, Texas Gulf, and as director of the Metro-politan Life and the Federal Reserve Bank, was freely placed at the service of the Club. It was equally char- acteristic that the generosity that financed the Red Cross Mission to Russia inspired the use of the Club funds for Belgian and war relief. "W. B.," as he is known to his many friends, was born at Virginia City in Alder Gulch, Mont., on May 13, 1869. His father, William Thompson, born at Cobourg, Ont., had drifted into the old Northwest and, hearing at Yankton of the gold strike at Bannack, crossed the plains on the Oregon trail in the summer of 1863, arriv-ing in Alder Gulch at the inception of a mining boom that lasted several years, during which something like $60,000,000 in gold was yielded by the placer diggings. His mother was a daughter of Maj. James R. Boyce, Sr., from Logan County, Ky., who had served under General Sterling Price of the Confederate Army. Major Boyce's ancestors were early settlers of the Old Dominion, and his grandfather had seen military service in the war for American independence. Major Boyce's mother was a descendant of the Marshall and Smith families of Westmoreland County, Va. When Thompson was eleven years old, the family moved to Butte, then a silver camp. He attended the public schools of Butte, but desiring a better education, entered Phillips Exeter Academy and later the Colum-bia School of Mines. Returning West, for a year or two he ran the Boulder Chief mine near Basin, Mont., which earned him a sobriquet, "Boulder Thompson." While here, some old ore sacks, oil-soaked, introduced him to flotation. He was also the first to leach some of the ore dumps of Butte.

Jan 4, 1928

By W. C. Schroeder

During the post-war period, and particularly during the past few years, coal production has been maintained at a reasonably constant level. This is in contrast to the greatly expanded demand for oil and natural gas. Certain markets for coal, such as the railroad and for home heating, have tended to decrease, but this decline has been offset by an increase in demand for other uses, particularly for electric power. Since the United States has very large reserves of coal and relatively limited reserves of natural gas and oil, from the conservation viewpoint, it would be better if the increased demand were to fall more heavily on coal. Where coal has lost certain markets, the decision has not always been made on the basis of price, and, in fact, in many instances, the markets have been lost where coal could show a price advantage. There are various reasons for this situation but it can be attributed in the main to the preference of certain consumers for the convenience offered by liquid and gaseous fuels. In the production of chemicals such as benzene, phenol, or ammonia, coal still plays an important role. As co-products from coke-oven operations, a wide variety of aromatic chemicals are available. In recent years, however, the production has not been sufficient to supply the demand, and it is not profitable to build coke ovens to make chemicals unless there is a market for the coke as well. As a result, the petroleum industry is beginning to take a stronger part in the production of aromatic chemicals. Natural gas has almost displaced the coke-oven water-gas machine for the production of hydrogen for the synthesis of ammonia, as well as for the synthesis of methyl alcohol and other oxygenated compounds. This information is not new and is given here only as a basis for the discussion of the broad significance of the development of the gasification process. It is clear that if coal is to regain some of its old fuel markets, as well as to maintain a position in the field of chemical synthesis, processes must be available for converting coal to the type of fuel the customer wants, and for a cheap method of furnishing gaseous raw material to the chemical industry. The operation of coke ovens and water-gas machines is not the answer to this problem for at least two important reasons: (1) the limited supply and relatively high price of good coking coals, and (2) the relatively high costs of the combined operations of coking and manufacture of water gas.

Jan 1, 1953

By D. C. Buffum, L. D. Jaffee

QUANTITATIVE measurements of the temper brittleness of steel are made by comparing the difference between embrittled and unembrittled specimens in the temperature of transition from ductile to brittle fracture. Since hardness affects the transition temperature, a study of the combined effects of hardness and temper brittleness appeared desirable. In this investigation a commercial SAE 3140 steel, which has been reported on previously in temper brittleness studies,* was used. Blanks from this steel were austenitized for 1 hr at 900°C and water quenched. The blanks were then divided into six groups and further heat treated as follows: Group 1—tempered at 675°C for 4 hr and water quenched; Groups 2, 3, 4, and 5—tempered at 675", 650°, 625', and 600 °C respectively for 1 hr and water quenched; and Group 6—tempered at 500°C for y2 hr and water quenched. Each of these groups was divided into two parts; one part was tested without further heat treatment, and the other was embrittled for 48 hr at 500°C and water quenched. Tempering treatments between 500" and 600°C were avoided because of the rapid embrittlement occurring in that range for this steel. The heat-treated blanks were machined into standard V-notched Charpy bars. Each group was tested over a range of temperatures on a 217 ft-lb Charpy machine. The energies necessary to fracture the bars and the percentage fibrous fracture of each bar were recorded. The transition temperatures were obtained from a plot of the percentage fibrous fracture as a function of testing temperature. They were taken as the lowest point on these curves at which the fracture was 100 pct fibrous. The transition temperatures for both embrittled and unembrittled specimens are presented in Fig. 1 as function of the hardness. It will be noticed in this figure that the point for the unembrittled condition at 21 Rockwell C is out of line. These specimens were tempered for 4 hr at 675 °C and this point indicated that under isothermal conditions at this temperature, as is well known, embrittlement may develop fast enough to more than offset the effects of softening. From this data, it was concluded that the difference between transition temperatures for the embrittled and unembrittled conditions at any given hardness, within the range of Rockwell C 24 % to 32lh, is constant. It is also concluded that, within the hardness range studied, the transition temperatures for embrittled and unembrittled specimens rise in a parallel fashion with an increase in hardness. The authors wish to acknowledge the assistance of Frank Carr in this work.

Jan 1, 1952

THE translators wish to record their appreciation of the help given by many individuals with whom they have discussed various details of the work. They are particularly indebted to Mrs. Anne Noble McKeachie, who initiated their collaboration; to Miss Cora Adamson, who spent many hours in making an accurate copy of a much-mutilated &st draft of the translation; and to the Yale University Library which gave access to its excellent collection of books on all aspects of the history of the sciences. The reader will share with the translators their obvious indebtedness to Mr. Carl P. Rollins, Mr. James W. Boyden, and the staff of the Printing-Office of the Yale University Press. The publication of this translation by the American Institute of Mining and Metallurgical Engineers has been made possible by a grant from the Seeley W. Mudd Memorial Fund, administered by a committee composed of Harvey S. Mudd, H. DeWitt Smith, and George Otis Smith. The translators are gratified that their work has been judged to fall within the scope of this Fund, which was established for the advancement of the sciences of mining and metallurgy by the encouragement of research and the dissemination of knowledge, and especially for the furtherance of such activities as might benefit the younger members of the profession. While Biringuccio's book would scarcely serve as a dependable text for the young mining student or metallurgist, it can give him a sense of his membership in a long-standing and honorable profession and enable him better to see his own work in true perspective. It is hoped that this English edition of a sixteenth-century Italian work will be read by the practicing metallurgist as well as by those who have already found pleasure in exploring the past of their profession. A man always feels more at home in a foreign country with men of his own craft than in his birthplace with those of different interests: As in space, so in time, and the modem metallurgist who may be unmoved by the literary and artistic Renaissance will quickly appreciate the spirit of that exciting period as he talks shop with Biringuccio on a visit to mine, smelter, forge, and foundry; as he sees in different forms the very furnaces and machines whose operation and response he knows so well; and as he discusses with this engineer of four centuries ago such topics as the best kinds of fuel or refractory for a given operation, and the importance of adequate supplies of power and material.

Jan 1, 1942

By R. W. Bowers

In order to hoist the ore according to grades, stope samples are taken. Three equidistant grooves are picked across the breast at right angles to the dip of the ore, the part removed being caught in the hand and then put into a small bag. When there is broken ore in the breast, the lines are continued down the pile and a small amount taken at intervals of the length of the sampler's pick handle. The quantity of sample from each breast will be between 2 and 3 Ib. If there are two grades of ore, bessemer and non-bessemer, there are two sets of brass checks for each chute, each check stamped with the number of the chute; one set of checks has the word "bessemer" and the other "non-bessemer." Before any ore is removed from the chutes, it is the duty of one man to see that the proper set of checks is at each chute in the mine. As each motor car is loaded, a check is attached to it. When the train reaches the shaft, the sample man removes the check on the first car, notes the grade, and directs the motorman to spot it over the proper pocket. The check is then hung on a hook with the number corresponding to the chute from which the ore came. The sample man throws a short rope with a knot in the end over the car and at the point where the knot falls a standard scoopful is taken. This is placed in a large bag that hangs directly under the hook containing the checks for that particular chute. These chute samples represent a check on the grading of the various contracts and by counting the tags a check is obtained on the miner's tally of the ore going into each chute; the total of the checks represents the hoist. During the stocking season, a standard scoopful is taken from each top tram car. This sample is taken in the same way as the chute samples at the plats underground. Top-of-car Samples These samples are taken by using a rope, preferably a clothesline, knotted each 18 in. of its length, and a hammer and a scoop. The standard scoop measures 31/2 by 21/4 by 11/4 in. and holds about 1/2 Ib. of ore. The rope, as applied to the usual railroad cars at the mine, is knotted into fifteen sections. It is placed diagonally over the car from

Jan 1, 1925

By E. C. Potter

FUEL-OIL was first substituted for coal at these works in September, 1888. It was first applied in the converting-department to the battery of boilers, consisting of 14 tubular boilers, 16 feet in length by 5 feet in diameter. To operate these boilers with coal for 24 hours required 14 strikers, 3 ash-wheelers, 6 men unloading coal, and 2 water-tenders, making a total of 25 men. With fuel-oil the same boilers require for the same period 2 water-tenders and 4 men to attend to the burners, making a total of 6 men. This gives a saving of 19 men, which, at an average of $2 per day each, amounts to $38 per day. Comparing the consumption of oil with that of coal, we find that for the week ending January 5, 1889, with an ingot output of 6403 tons, 2731 barrels of fuel-oil were used as against a necessary consumption of coal for the same work of 848 tons, showing 3.22 barrels of fuel-oil to be equivalent to one ton of Indiana block-coal. Figuring oil at 60 cents per barrel, and coal at $2.15 per ton, we have as the cost of oil $1.93, as against $2.15 for its equivalent in coal. In December, 1888, the rail-mill battery of 26 boilers, of the same dimensions as those in the converting-department, was equipped for fuel-oil. For the week ending January 5, 1889, with a rail out-put of 5208 tons, 5987 barrels of oil were consumed, as against a necessary consumption of coal, to do the same work, of 1805 tons, showing 3.31 barrels of fuel-oil to be equivalent to one ton of Indiana block-coal, which at the costs named above would show $1.98 worth of fuel-oil to he equal to $2.15 worth of coal. The labor required to operate the rail-mill boilers for 24 hours, with coal as fuel,is: 26 stokers, 4 water-tenders, 6 ash-wheelers, 12 men unloading coal; total, 48 men. With oil as fuel, the same work requires 4 water-tenders and 6 men to attend to the burners; total, 10 men; a saving over coal of 38 men in 24 hours, which, at an average price of $2 per day, would be $76 per day. In the brief experience we have had with oil as fuel, we find that the efficiency of the boilers is somewhat increased and the repairs are

Jan 1, 1889

By Geoffrey Gilbert

THE Montana Phosphate Products Co., subsidiary of the Consolidated Mining and Smelting Company of Canada, operates three phosphate properties north and northeast of Garrison, Powell County, Mont. Production of all three is from the same phosphate bed, a 3 to 4-ft. member of the Phosphoria formation, whose outcrop is traceable across the mountains of the Garnet Range in a series of southeasterly pitching folds. Because of topographical differences and of variations in the attitude of the bed, each property has its own mining methods and problems. Most of the phosphate rock produced since I930 has been shipped to the plant of the Consolidated Mining and Smelting Co. at Trail, B.C., where it is treated with sulphuric acid for conversion to phosphoric acid, which in turn is used to produce various fertilizers. HISTORY The occurrence of rock phosphate in Montana has been known. since 1910, and the Garrison area was mapped by the United States Geological Survey in 1913In the nineteen twenties William Anderson, owner of a ranch 8 miles north of Garrison, discovered phosphate on his land, and the Montana Phosphate Co., which later became the Montana Phosphate Products Co., was formed to work the deposit. Montana Phosphate Products Co. later obtained United States leases on two adjoining parcels of ground, and this combined property, known as the Anderson mine, has been the main source of Consolidated's phosphate rock. The mine now includes an adjoining parcel leased from Anaconda and mined from the Anderson workings. In 1940, the Graveley mine, a small privately owned property 6 miles east of the Anderson, was leased from the owner by Montana Phosphate Products Co., and a U. S. lease held by Graveley on some adjoining ground was subleased. In 1943 the Luke mine, on the Mineral Hill property, 1 ¾ miles south-southwest of the Graveley, a U. S. lease, which previously had produced a few thousand tons, was optioned from the lessees by Montana Phosphate Products Co., and is now being developed. At both these mines the rock is appreciably higher grade than at the Anderson mine. GEOLOGY The Phosphoria formation is the Permian member of an extensive sequence of Paleozoic and Mesozoic rocks. It is underlain by Pennsylvanian (Quadrant) quartzite and Mississippian limestone, and overlain without any marked unconformity by Jurassic (Ellis) shale and Cretaceous shale and sandstone. In the Garrison area, the Phosphoria itself consists mainly of about 50 ft. Of gray to yellow chert. Immediately below the chert is the phosphate, usually 3 to 4 ft. thick. Below the phosphate occur a few

Jan 1, 1945

By B. F. Koch

COPPER reverberatories develop large amounts of exit gases of a temperature in the neighborhood of 2000°F. The gases are not only of a noxious nature but must usually be disposed of at considerable heights above the yard level by a stack. Handling these gases at the temperature mentioned would require rather expensive construction of conveying flues and stack. Moreover, wasting such amounts of heat is certainly most uneconomical. Numerous investigations have indicated that waste heat boilers of the water-tube type are the most practical and economical means for utilizing that heat although the gases are heavily laden with rock dust and copper-bearing slag, which upon cooling form hard deposits on the surfaces of dampers or heat absorbing elements placed in the gas stream. Avoiding Slag and Dust Deposits Based largely on the experience of the paper industry in burning black liquor, a waste heat boiler design was developed a few years ago, providing not only extensive water-wall surfaces for cooling the gases below the fusing point of the slag but also settling out, as far as possible, the solidified particles of slag by creating low gas velocity. Matter carried in a stream of gases or air has a tendency to maintain its original direction upon a change in the direction of the flow of the conveying medium. Reverberatory waste heat boilers installed at Hurley and Morenci endeavored to utilize that tendency for the elimination of slagging particles at predetermined places and before they would strike the tube banks of the boilers. Both installations were successful in minimizing the slagging of boiler tubes and thereby minimizing the need for hand lancing. However, the low draft carried at the up-take of the reverberatory furnaces resulted in a positive pressure in the upper part of the furnace of the waste heat boilers, causing the emission of gases from lancing doors and making more difficult the already unwelcome work of cleaning the boilers by handlancing. Attempting to correct this nuisance as much as possible, the overall height of the Chuquicamata waste heat boilers has been reduced to the minimum considered necessary to obtain proper water circulation in furnace walls. Moreover, it is attempted to solidify slag and dust particles by providing large amounts of water-cooled surfaces before the gas stream reaches super-heater and convection banks of the boilers. The furnaces have been made as deep as an economical and practical arrangement of headers for water

Jan 1, 1952

By C. A. Stetefeldt

IK the dry-crushing of ores, either by stamps, rolls, or other machinery, it is essential that the material should be free from moisture. Hence a contrivance which effects this with economy, and is of durable and compact construction, is a great desideratum. It is claimed for the below-described shelf dry-kiln, that it possesses these qualifications in a high degree. The construction of the shelf dry-kiln is based on the Hasenclever principle. That is to say, a number of inclined shelves are arranged zig-zag above each other in a vertical shaft, having openings or slits where they meet, on which the ore rests in a stratum, the thickness of which is governed by the width of the slits and the inclination of the shelves. If a portion of the charge is removed at the end of the bottom shelf, a sliding motion of the ore takes place on all shelves above, and the top shelf is replenished from a hopper set over it. It will be seen that the shaft is divided by the shelves into a number of triangular prismatic spaces. Through these the hot gases from a fireplace are made to circulate, each space communicating with the next one by a flue arranged in the sidewall of the shaft. These flues being located on alternate sides of the shaft, a continuous passage is formed through the whole structure. After thus stating the principle of the construction, its details will be easily understood by reference to the drawings, Fig. 1 to Fig. 5. The drawings, Fig. 1 to Fig. 4, represent two kilns united into one structure. The cast iron shelves(a) are 2 feet 4 inches wide and 5 feet long, with sides and a back 4 inches high, and are cast a full halfinch thick. How they rest on the brackets(d), and interlock each other, is shown in Fig. 5. Three such shelves, with an inclination of 38') are placed in one row in a brick shaft 7 feet 1/2 inch wide and 4 feet deep. The ore hoppers(g) rest on the iron bems(f). At the end of the bottom shelves are the discharge-doors(b), with shoots projecting beyond the front wall. A swinging apron(e) keeps the ore in place. By dropping it a car below the shoot is filled with dry ore. A number of extra-large pieces of ore may cause a stoppage in the slits ; for such an emergency the openings(e) are provided, through

Jan 1, 1884

I AM sure, that you understand that of all the things created by the most high God Himself or by Nature at His command, not one-even though it be an atom or the smallest worm-has been produced without some particular gift. And if we do not always discern this in every thing, the cause lies in our defective vision, in our little knowledge, and in our lack of careful thought concerning the necessity of seeking hidden things. Certainly those things that have such inner powers, like herbs, fruits, roots, animals, precious stones, metals, or other stones, can be understood only through oft-repeated experience. [37] Others do not need so much knowledge and belief for their, powers are obvious and shown to us at all times by their effects. They reveal themselves to us through the sense of sight by their splendor and variety of colors, through the sense of smell by their odors, through the sense of hearing by the melody of the harmonious or unpleasantly discordant repercussions. of the air. They likewise manifest themselves by. their softness or harshness. As you see, all those things, according to. their limits, are conveyed .by the ordinary senses to the mind, by whose distinctions all their species, both harmful and beneficial, are discerned. Then they are reviewed by the judgment in all their degrees of perfection and imperfection, so that whoever seeks them with careful study or with experience often finds them. Now, in order to shorten this discourse, since I wished to speak to you of lodestone and its properties, I tell you that it is one of those things that show their apparent effects to our sight by a particular virtue hidden in such a way that its cause, as far as I know, has never been known to the very wise natural speculators who have spoken on every other subject. Thus one who considers its actions carefully must surely marvel, for it appears that Nature has put into this stone a certain spirit of vivacity, so that it seems to have-I would like to say-hands, although they are not seen. For I see that it not only attracts iron but also takes hold of it and keeps it attached to itself. This action is certainly great enough to bear certain witness to the virtues possessed by other created things that do not manifest their powers to the external senses. In order not to prolong this discussion, I tell you the following. This stone is found in various places and of different colors and properties. The

Jan 1, 1942

By Edward H. Robie

SEPTEMBER usually being a fine month for motoring, we set out with our better half at the end of August in our Studebaker for points West. A combined business trip and vacation. The first night found us 392 miles away, at the Statler Hotel in Buffalo, and the next morning we revisited Niagara Falls for the first time in some forty years. The cataracts were as impressive as ever and certainly worth a day of any vacationist's time, instead of the half hour we could spare before going on to Chicago. The Centennial of Engineering, the hundredth anniversary of the founding of the ASCE, no doubt attracted the greatest gathering of engineers in history but still the attendance was disappointing to most of the forty or fifty societies that participated. Perhaps the time-the two weeks following Labor Day-was unfavorable. Few could afford to spend ten days away from home and business at that time of the year. Fall meetings of the AIME normally attract far more than the 300 that registered in Chicago. The technical program, however, was excellent, especially that arranged by the Minerals Beneficiation and Industrial Minerals Divs. The mineral industry papers of a more general nature that were presented as a part of the Centennial program on Monday and Tuesday of the following week were of high quality and offered by top names but had a meager audience. Undoubtedly the celebration brought engineers and engineering to the attention of millions of people. The pageant at the Museum of Science and Industry proved continuously interesting, showing the progress of engineering following the first use of fire. The show continued for many weeks. A special stamp was issued by the Government, which engineers might well use on their Christmas cards or other mail this year. After six days in Chicago we set out north, first visiting Fairbanks Morse in Beloit and Allis-Chalmers in Milwaukee. Will Mitchell's Basic Industries Research Laboratory is doing interesting work and being installed in more comfortable quarters. The next day at Ishpeming, C. W. Allen arranged for luncheon with a local group of AIME members and we then looked over the new surface plant of the Mather B mine, a model of modern functional design. Then on to a small dinner meeting at Calumet following cocktails at Endicott Lovell's attractive summer home on the lake at Point Mills. The new Memorial Union Bldg. at Houghton, where we were domiciled for the night through the courtesy of Roy Drier, is a beautiful modern addition to the college, a model of its kind.

Jan 1, 1952

By John L. Baum

Tests show that 50 times the earth's normal field can exist near stacked drill rods. Protection against the effect of these strong fields can be obtained by means of a removable sleeve of common iron pipe. GEOLOGISTS and engineers working around a diamond drill rig have often had the opportunity to observe the magnetic attraction of drill rods pulled out of the hole for core removal. This is sometimes an amusing pastime, but this same magnetic force inadvertently applied to a compass needle can cause it to lose its polarity entirely or to become reverse polarized when placed in the immediate vicinity of stacked rods. The first recommendation, of course, would be to avoid the rods, but in surveying an operating drillhole this is not always possible; therefore steps must be taken to neutralize the magnetic effect of the drill rods. Early in the summer of 1949 the geological department of the New Jersey Zinc Co. undertook at Franklin, N. J., an extensive program of surveying the course of deep diamond drillholes. The majority of the holes were surveyed while in the process of being drilled, and considerable difficulty was encountered. A pattern for the deviation of drillholes had been established for the district from surveys in holes from which the drill rig had been removed. It was observed that a certain operating deep drillhole being surveyed did not fit this pattern. In the resulting confusion of repeated surveys and cementing a plug for wedging operations, the lower 1800 ft of the hole was lost. Because of this incident studies were initiated to determine the source of the difficulties and to develop safeguards against recurrence of faulty surveys. Using a hand magnet easily shows that the polarity of a compass needle can be reversed if rotation of the needle is hindered through tilting of the compass or clamping of the mechanism. Such experiments are not recommended, especially in the case of the clockwork type of instruments. A magnetized hairspring in a clockwork instrument will cause the compass card to assume a periodic motion which will not stop until the clockwork runs down. Routine check readings of instrument north before and after each survey are not always sufficient to catch instances of reversed polarity of the compass needle. Although the majority of instances probably take place while the instrument is being removed from the hole with needle in fixed position, it is demonstrable that a 'luggish needle, weakened during a previous test, can be reverse polarized

Jan 1, 1955

By Joseph L. Jernegan

The Whale Lode occurs in the main range of the Rocky Mountains, Park County, Colorado Territory, at Hall Valley. It has been opened up and worked to some extent by the Whale Mine, situated some 11,300 feet above the level of the sea. The mine, with 700 feet of the lode on either side of the discovery shaft, is the property of the Hall Valley Silver-Lead Mining and Smelting Company. The adjacent country rock is a compact, fine-grained gneiss; its general strike is about north and south, dipping steeply to the west. In the immediate vicinity of the mine, the strata are very nearly vertical. The gneiss incloses numberless veins of a reddish granite, in which the feldspar largely predominates over the quartz and mica, the latter oftentimes being scarcely perceptible. As a general rule these granitic veins seem to more frequently follow the lines of stratification of the gneiss than otherwise. They are of varying width, some large, some small; the larger are from 5 to 6 feet wide. Gash veins of feldspar and quartz are also of very frequent occurrence. The general trend of the lode is about northeast. and southwest, intersecting the country rock at about an angle of 45 to its stratification. It dips to the northwest at an angle of 65. I am unable to state accurately how far this lode has been traced upon the surface, but it is at least well known to extend entirely through the mountain upon which the mine is situated, and is traceable over the ridge by a hollow extending for some distance along the surface, in which the lode crops out. This hollow in the surface rock has probably been formed through decomposition of the vein matter by atmospherical influences. The width of the crevice is variable, generally between 5 and 10 feet; the pay vein varies from an inch, or less, to 36 inches. The vein is generally accompanied both on foot and hanging walls by a whitish, semi-decomposed fock, composed of quartz and decomposed feldspar, and in some places—where the process of decomposition has not reached as advanced a stage—a lightgreenish or black mica. This rock, therefore, is in places composed of all the constituents of gneiss, and is undoubtedly nothing more or less than the same in a decomposed condition. It is often very strongly impregnated with iron pyrites, generally crystallized in minute cubes, and it is probably owing to the presence of this min-

By D. M. Dunbar

LONG before Columbus discovered America the original inhabitants toiled in the copper workings of the Andean Cordillera. Their best diggings appear to have been at Chuquicamata, site of the huge present-day open pit owned by the Chile Exploration Co., subsidiary of Anaconda Copper Mining Co. Located in Antofagasta Province of northern Chile, Chuquicamata is in the Atacama desert, high on the western slope of the Andes at 9500-ft elevation. In the Chuquicamata area the Atacama desert merges into the Cordillera. The climate is extremely arid and precipitation, either in the form of rain or snow, is very infrequent. The temperature varies from 50° to 85°F during the day, and drops to 20° to 40° at night. The Antofagasta and Bolivia Railroad, which connects the Chilean Port of Antofagasta with La Paz, Bolivia, passes within approximately 6 miles of the plant. A branch from the main line to Chuquicamata serves the property for outgoing copper and incoming freight. The distance to Antofagasta by rail is 163 miles. Previous to the Inca conquest, this region was inhabited by the Chuco Indians, a small tribe, descendants of the Aymaras and Quechuas. The Incas, whose capital was located in Cuzco, Peru, gradually extended their empire to the south, reaching at one time to what is now central Chile. It is believed that they built crude primitive furnaces on the banks of the Rio Salado where on a small scale they smelted copper ore from Chuquicamata. At the time of the subsequent Spanish conquest, legend has it that Diego de Almagro, on his return to Cuzco in 1536 after his invasion of Chile, obtained from these furnaces metallic copper for horseshoes. During the period from 1560 to 1879 the high grade veins of the Chuquicamata deposit were worked superficially by the Spaniards and Bolivians. The treaty signed after the war of 1879 recognized the sovereignty of Chile over this territory and Chile, realizing the importance of the district, started to develop it in an orderly manner, although only high grade veins were worked. New Process Is Key Reports on the deposit were brought to the attention of Albert C. Burrage, a Boston lawyer and financier, in 1910. Chuquicamata was described as a huge deposit of ore that was not amenable to the usual treatment by concentrating and smelting since much of the copper occurred as oxides. He had been working on a process for the recovery of copper from sulphide ore which involved a sulphating roast, leaching of the roasted product, and pre-

Jan 1, 1952

AMERICANIZE THE MINING INDUSTRY Americanization is the snaking of American citizens; men and women controlled by the ideals of American citizenship, which have been built up by this country's heritage and its unceasing struggle for freedom and democracy and opportunity. That means, first of all, a necessary understanding of what those ideals are and what they mean for the newly arrived foreigner. It means that every kind of anti-American propaganda must be stamped out; that racial prejudices and the misunder-standings which lead to unrest and disloyalty and make fruitful soil for anti-American propaganda must be overcome. The foreigner must understand. He must understand what we are trying to do here in America; he must understand something, at least, of the kind of government we have built up in our efforts to, accomplish our particular aims; he must understand how lie can fit into it all, not only to help America, but to help himself-to make it possible for hint to get from this country what he carne here seeking. First of all, he must learn the American language. He must be able to talk with his fellow Americans-those who were born here and those who have recently cone, like himself, but from a different land. The most dramatic, the most crucial demonstration of the urgency of the need of all this is given to us right now. At the time when it is most essential for this country to be solidly American, enemy propagandists are winning an occasional success here because they give their message to men and women and boys and girls who do not understand our language and consequently do not understand us. These foreigners, whom the enemy is trying to make disloyal, are really in our army, the big army that is fighting the war for America. Most of them are not among the soldiers who will fight on the battle front, but they are in the lines back of these soldiers. The worker in the shipyards and in the mines is just as important a soldier in this war as the man in the trenches. That has been said over and over, but it cannot be said too often. It is just as vital for that man in the mine to know why we are at war as it is for the soldier. His employer has just as great a responsibility to the country as has any general, and it is the same responsibility.

Jan 8, 1918

By Pol Duwez, Paul Pietrokowsky

The crystal structure of the compound TisGeS has been determined from X-ray powder diffraction data. Related silicon and tin compounds have been found to be isomorphous. Unit cell dimensions, axial ratios, and parameters for equivalent atomic positions are given. THERE is, at present, only meager information pertaining to the solid state reactions of titanium with the elements in group 4B of the periodic table (silicon, germanium, tin, and lead). The only two compounds whose crystal structure has been established are TiSi² and TiGe² (references 1 and 2 respectively). These two compounds are isomor-phous and have an orthorhombic symmetry D242h— Fddd. The titanium-rich regions of the constitution diagrams of titanium-silicon, titanium-tin, and titanium-lead have been investigated by Craighead et al.³ While valuable information concerning the alpha solid solubility of these three elements in titanium was obtained, no light was shed on the existence or nature of the titanium-rich compound in these systems. The present study is concerned with the crystal structure of the intermediate phases Ti5Si ?, Ti³Ge³, and Ti5Sn³, which were found to be isostructural. The alloys were prepared by mixing the pure metal powders in the desired proportions, pressing the mixture into pellets, and melting them in an electric arc furnace in the presence of a helium atmosphere.& After melting, the specimens, weighing approximately 5 g, were sealed in evacuated quartz vials, homogenized at 1038°C for three days, and quenched from that temperature. Powder diffraction patterns were made with a 143.2 mm diam Debye-Scherrer X-ray camera in which the Ievins and Straumanis film arrangement was utilized. Filtered copper radiation was used throughout the entire investigation. A study of the powder patterns of a series of alloys of various compositions indicated the presence of a compound around a composition corresponding approximately to a ratio of 3 titanium to 2 silicon, germanium, or tin. From a visual examination of the diffraction patterns, it was evident that the silicon and germanium alloys were iso- morphous. For small angle reflections, the powder pattern of the tin compound was analogous to that of the silicon and germanium compounds, but after the first ten reflections, the similarity was no longer clear. The powder pattern of the germanium compound was selected for indexing, since it exhibited a weak small angle reflection and clearly resolved doublets in the back-reflection range. Good agreement between observed and calculated values of (1/d)² was found by indexing the pattern on the basis of hexagonal symmetry. For the hexagonal system:

Jan 1, 1952