Search Documents

By L. A. Willey

Although the interierometric method for the determination of length changes was devised by Fizeau more than three quarters of a century ago, it has not achieved the widespread use in the metallurgical field that its precision and simplicity would seem to warrant. The interferometer and the basic principle are both very simple. When optically plane surfaces held at a very slight angle to each other are illuminated by monochromatic light, rectilinear, equally spaced interference fringes arc formed. Each fringe corresponds to a defiuitc thikness of the wedge formed by the optical flat.;. The difference in wedge thickness between two consecutive fringes is cqual to one half the wave length of the illuminating light. Instruments for vicwing the intertero~ncter have passed through a number of modifications. Outstanding among the improvements were those Abbe. in 1884. His improved instrument permitted micrometric mcasurements to the order of one-hundredth of the width of an interference fringe (i.e., lengths were measured to the order of one two-hulldredth of the mave length of light ). It also permitted the consecutive use of light of several wave lengths. which made possible the determination of the order number of any fringe and therefore the absolute thickness of the wedge at any point. The Abbe dilatometer and methods of measuretment, including corrections to he applied for the change of index of refraction with change in tempcrature and barometric pressure in an air wedge, have been thoroughly described by Pulfrich.' Pulfrich2 made further improvements in the interference measuring apparatus. His instrument embodied all the features of the Abbe dilatometer but was made more versatile by its complete mechanical separation from the interferorneter. The introduction of an Amici prism in the piece permitted the simultaneous observ tion of the whole set of fringe systems developed in the interferometer from the visible light of a geisler tulle. .Also, the introduction of a direct-vision, reflecting prism made it possible to set the fringes parallel to the two vertical fiducial line. of the instrument without the necessity of rotating the interierometcr. Interferometric methods employed ill this country have been developed and dcscribed by Priest, Pelers and Cragoe," Austin,5 Merritt,= Saunders,? and Nix and MaNair. Since none of these authors used the type of instrument that was employed in the present investigation, they Will not be discussed here. This paper will be limited to the description of the interfernmetric apparatus and method used at the Aluminum Research Laboratories and to the presentation of data so obtained. Apparatus and Procedure A general view of the dilatometer, not including equipment for controlling and

Jan 1, 1945

By James T. Gow, Oscar E. Harder, Anton de S. Brasunas

THIS paper deals with the results obtained and the techniques employed in determining: I. Liquidus and solidus temperatures of the HH and HT type heat-resistant alloys. † 2. The relation of true temperatures (thermocouple) to apparent temperatures (optical pyrometer) for the molten HH and HT type alloys. This work was the outgrowth of needing to know something definite about these temperatures in order to study the effect of pouring temperatures, shake-out times, and heat-treatments on the properties of some heat-resistant alloys. The information developed is thought to be of interest to industry for guidance in foundry practices and the industrial heat applications of the alloys. This paper is based upon work that has been done for the Alloy Casting Institute at Battelle Memorial Institute. LIQUIDUS AND SOLIDUS TEMPERATURES OF HH AND HT TYPE ALLOYS Experimental Procedures Temperature-time curves were obtained during the cooling and solidification of several HH and HT type alloys. The metal was melted in an Ajax high-frequency induction furnace and poured into a coresand mold for cooling. The temperature measurements were obtained by means of a platinum, platinumrhodium thermocouple contained within a fused silica sheath, which was extended through the side wall of the dry core-sand mold to a point at about the center of the mold cavity, which was 3 in. in diameter by 5 in. deep. The cold junction of the thermocouple was kept in an ice bottle, and the temperature was recorded automatically on a direct-reading potentiometer recorder. Through a switching arrangement, the temperature recorded was checked occasionally with a portable Leeds and Northrup potentiometer indicator. Less than a 5°F. variation in the two instruments was always found. This is within the limit of accuracy of readings. The thermocouple used was checked for accuracy against a standard couple, both before use on this work and after completion of the work, by the instrument laboratory. Temperature-time Cooling Curves Fig. I is an enlarged reproduction of a part of one of the cooling curves over the temperature range of 2600° to 2200°F. for an alloy of the HT type with 0.45 per cent carbon, 16 per cent chromium, and 36 per cent nickel. This is a typically shaped cooling curve as obtained for the alloys. It will be noted that two temperatures are shown on Fig. r for the liquidus temperature. It is thought likely that the higher temperature, A, at the point at

Jan 1, 1945

By I. Fatt

This paper proposes the network of tubes as a model more closely representing real porous media than does the bundle of tubes. Capillary pressure curves are derived from network models and pore size distributions are calculated from these curves. In this way is shown the difference between the true and calculated pore size distributions when the capillary pressure curve is used to obtain pore size distribution for porous media. INTRODUCTION Despite the technological importance of the laws governing flow through porous media, many of these laws have not yet been clearly formulated. This is especially true of the laws governing multiphase flow. The static properties, such as the capillary pressure curve, are also not at present interpretable correctly in terms of the pore size distribution and other structural properties of porous media. In the absence of any well founded theoretical description of fluid flow through porous media, many empirical descriptions have been proposed. In addition to the strictly empirical flow equa- tions, some equations have been developed rigorously from simple geometrical models of the pore spaces. These equations are only as valid as is the model used in their development. The two models used in the past, the sphere pack and the bundle of tubes, have been too simple, and as a result, the equations derived from them have failed to predict the observed properties. Agreement between theory and observation has been achieved for these models by inserting parameters of doubtful physical significance. The work to be reported here was undertaken in the belief that the study of a model more closely resembling most real porous media than does the sphere pack or bundle of tubes would yield useful information concerning the structure of real porous media and the relation between structure and flow properties. There was no intention of developing any calculational procedures, as for example calculating relative permeability from capillary pressure data. The objective of the study was instead to develop a better qualitative understanding of the relation between the various measurable properties of porous media. The model chosen for study is the network of tubes in which each tube represents a pore space in the porous medium. Microscopic observations leave no doubt that sandstones and clastic carbonates are three-dimensional irregular networks of irregularly shaped pores. The irregularity of these structures makes any accurate theoretical study of their properties impossible. Results from an oversimplified model such as the bundle of tubes are worthless when applied to real systerns. The sphere pack model, on the other hand, not

Jan 1, 1957

By H. S. Kalish, F. J. Dunkerley

Introduction and Previous Work THE determination of the low temperature tensile properties of tin and tin-lead alloys was initiated as part of an extensive research program on the phasial equilibria of tin binary systems below 13.2°C and the property changes associated therewith. A survey of the literature revealed that, although some room temperature tensile data were available for tin and a few tin-lead alloys, there existed no survey report of the low tcmPerature tensile properties of these alloys. Accordingly, the tensile data for tin and a series of pure tin alloys containing from 0.01 to 50 pet lead were measured at eleven temperatures horn — 196 to +20°C and are presented here in survey form. In addition to the importance of these tensile data as a preliminary to certain fundamental research, this information promises also to be of commercial importance because of the extensive use now being made of tin-lead solders in refrigeration and gas liquefaction equipment. Occasional failures of the solders in low temperature service have been attributed by some metallurgists to low temperature embrittlement, while others hold that failure results from the transformation of the tin-rich phase of the solder from the solid white (beta) to the powdered gray (alpha) form. From the data previously available in the literature, neither of these explanations can be completely corroborated. cohen and van Lieshout have estab-lished the beta to alpha tin transformation at 13,2°C and have shown that strain accelerates the transformation. Further, they showed that although I pct lead retarded the transformation, it was not eliminated. It will be pertinent, then, to note whether the beta to alpha transformation of the tin.rich phase will occur in a short-time tensile 'test. polanyi and schmid2 studied the tensile properties of tin single crystals at — 185°~ and report that tin is britlle at this tem-perature. In 1946, Kostenets3 reported that pure tin was brittle at —Ig6 and — 253°~, while lead remained ductile at both these temperatures. He also studied the tensile properties of tin-lead alloys containing from 10 to 75 pet lead at —253, —196 and + I~OC. The ultimate tensile strength increased more than two times in going from room temperature to — I96°C and about three times that value on further cooling to — 253 C- All the alloys were brittle at — 196'C except those containing more than 75 pct lead. Even at — 253'C, the 75 pct lead alloy retained 36 pet elongation in a 30 mm-ga. length. Creep is also an important phenomenon

Jan 1, 1949

By G. K. Manning, C. H. Lorig

TWO metallurgical tools have acquired wide use within the past several years as a means of studying the transformation characteristics of steel. One is a technique used first by Bain and Davenport for determining the transformation characteristics of a steel at constant temperature; the second is the end-quench hardenability test. Constant-temperature transformation curves like those of Bain and Davenport have done much to rationalize the metallography of steel; however, in commercial practices, constant-temperature transformation is seldom encountered, therefore only rarely can such curves be directly applied. The real reason for the determination of such curves lies in the fact that they provide a way of thinking about transformation that is both convenient and productive. The end-quench hardenability test is a more practical means of studying transformation, for, by correlating positions on the hardenability bar with shapes of different masses, an almost direct application of the results can be made. Unfortunately, the end-quench test, though practical, can do very little toward improving the metallurgists' way of thinking about transformation. These two metallurgical tools, dealing with precisely the same phenomenon, should be very closely associated in metallurgists' minds. Actually, they are frequently pushed into separate mental corners and considered as being more or less distinct and unrelated. The reason for this is that no strong connecting link between them has been developed. An attempt is sometimes made to relate these two tools by projecting the critical cooling rate on the isothermal transformation plot as illustrated in Fig. I. The critical cooling rate is considered as a constant rate-though in practical applications, cooling rates are never constant—and this constant cooling rate is given uniform significance from the Ae temperature down to the temperature of initial transformation. A little thought indicates the errors of such a procedure. Certainly the time interval spent just below point A of Fig. I cannot be as effective in promoting nucleation as is the time interval spent just above point B. Yet the procedure represented in Fig. I considers all the time spent between temperatures A and B to be just as effective in promoting nucleation as though all the time were spent at temperature B. Furthermore, change the shape of the isothermal curve between points B and C in any way desired, and the required critical cooling rate is not changed one iota. This cannot possibly be true. Such a way of thinking about critical cooling rates not only is incapable of giving any results that are quantitatively satisfactory but is likely to give very misleading qualitative results.

Jan 1, 1947

By G. K. Manning, C. H. Lorig

TWO metallurgical tools have acquired wide use within the past several years as a means of studying the transformation characteristics of steel. One is a technique used first by Bain and Davenport for determining the transformation characteristics of a steel at constant temperature; the second is the end-quench hardenability test. Constant-temperature transformation curves like those of Bain and Davenport have done much to rationalize the metallography of steel; however, in commercial practices, constant-temperature transformation is seldom encountered, therefore only rarely can such curves be directly applied. The real reason for the determination of such curves lies in the fact that they provide a way of thinking about transformation that is both convenient and productive. The end-quench hardenability test is a more practical means of studying transformation, for, by correlating positions on the hardenability bar with shapes of different masses, an almost direct application of the results can be made. Unfortunately, the end-quench test, though practical, can do very little toward improving the metallurgists' way of thinking about transformation. These two metallurgical tools, dealing with precisely the same phenomenon, should be very closely associated in metallurgists' minds. Actually, they are frequently pushed into separate mental corners and considered as being more or less distinct and unrelated. The reason for this is that no strong connecting link between them has been developed. An attempt is sometimes made to relate these two tools by projecting the critical cooling rate on the isothermal transformation plot as illustrated in Fig. I. The critical cooling rate is considered as a constant rate-though in practical applications, cooling rates are never constant—and this constant cooling rate is given uniform significance from the Ae temperature down to the temperature of initial transformation. A little thought indicates the errors of such a procedure. Certainly the time interval spent just below point A of Fig. I cannot be as effective in promoting nucleation as is the time interval spent just above point B. Yet the procedure represented in Fig. I considers all the time spent between temperatures A and B to be just as effective in promoting nucleation as though all the time were spent at temperature B. Furthermore, change the shape of the isothermal curve between points B and C in any way desired, and the required critical cooling rate is not changed one iota. This cannot possibly be true. Such a way of thinking about critical cooling rates not only is incapable of giving any results that are quantitatively satisfactory but is likely to give very misleading qualitative results.

Jan 1, 1947

By R. W. Shoenberger, J. D. Clendenin, W. L. McMorris, N. Schapiro, B. R. Kuchta, A. A. Terchick, R. J. Gray, J. G. Price

INTRODUCTION * The United States is fortunate in having enormous reserves of metallurgical-grade coals. Although these coals are better in quality and more accessible than most coals found throughout the rest of the world, the best grades of these coals are being depleted. Consequently, more efficient exploration tools and techniques, such as advanced methods of core drilling and logging, correlation by palynology,** stratigraphy, paleontology and petrography are being used to help assess the extent and quality of the remaining coal reserves. Exploration and assessment of new and existing coal properties become of utmost importance in determining (1) the economic justification for mining the coal, (2) the optimum design of the preparation plant and (3) the most effective use of the coal. Fortunately, the cost of mining coal has remained stable because of better mine planning, more efficient operations and increased mechanization of mining operations. However, increased mechanization raises the amount of impurities in the coal mined, and this requires more and better coal beneficiation to meet the more stringent quality requirements set by the market. Besides, mechanical miners also produce relatively fine coal and, to ensure maximum liberation of impurities, much of the coal presently being used must be crushed to a finer size prior to preparation. The bulk of all coals presently used in this country is mechanically cleaned, much of it at a lower specific gravity than in the past. This necessitates the use of new and improved processes and equipment for coal washing and recovery, such as heavy-medium cyclones and vessels, and froth flotation cells. However, because wet-cleaning processes are pre- dominant in the United States and fine coal retains large amounts of moisture, the increased production of cleaned fine coal accentuates the need for new or improved methods and equipment for dewatering and drying this coal. The larger amounts of coal being beneficiated and the use of new and improved beneficiation processes will aid in controlling and ultimately eliminating sources of pollution. Modem coal markets demand coals that meet rigid specifications. Most coals are purchased under contracts that specify moisture, ash, and sulfur contents, or heating value, depending upon the end use. There has also been a growing trend toward specifying other properties, including particle size and coking capability. These specifications may include not only the * Editor's note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections prepared by each individual as has been done in other chapters. ** Palynology is the study of plant microfossils, especially spores, pollen, and other types of fossils not usually studied by paleontologists.

Jan 1, 1968

By J. R. Long, T. R. Graham

THIS report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. PRELIMINARY WORK In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, 0 to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening, effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By H. S. Kalish, F. J. Dunkerley

INTRODUCTION AND PREVIOUS WORK THE determination of the low temperature tensile properties of tin and tin-lead alloys was initiated as part of an extensive research program on the phasial equilibria of tin binary systems below 13.2°C and the property changes associated therewith. A survey of the literature revealed that, although some room temperature tensile data were available for tin and a few tin-lead alloys, there existed no survey report of the low temperature tensile properties of these alloys. Accordingly, the tensile data for tin and a series of pure tin alloys containing from 0.01 to 50 pct lead were measured at eleven temperatures from -196 to +20°C and are presented here in survey form. In addition to the importance of these tensile data as a preliminary to certain fundamental research, this information promises also to be of commercial importance because of the 'extensive use now being made of tin-lead solders in refrigeration and gas liquefaction equipment. Occasional failures of the solders in low temperature service have been attributed by some metallurgists to low temperature mbrittlement, while others hold that failure results from the transformation of the tin-rich phase of the solder from the solid white (beta) to the powdered gray (alpha) form. From the data previously available in the literature, neither of these explanations can be completely corroborated. Cohen and van Lieshout1 have established the beta to alpha tin transformation at 13.2°C and have shown that strain accelerates the transformation. Further, they showed that although I pct lead retarded the transformation, it was not eliminated. It will be pertinent, then, to note whether the beta to alpha transformation of the tin-rich phase will occur in a short-time tensile test. Polanyi and Schmid2 studied the tensile . properties of tin single crystals at -185°C and report that tin is brittle at-this temperature. In 1946, Kostenets3 reported that pure tin was brittle at -196 and -253°C, while lead remained ductile at both these temperatures. He also studied the tensile properties of tin-lead alloys containing from 10 to 75 pct lead at -253, -196 and +17°C. The ultimate tensile strength increased more than two times in going from room temperature to -196°C and about three times that value on further cooling to -253°C. All the alloys were brittle at -6°C except those containing more than 75 pct lead. Even at -253°C, the 75 pct lead alloy retained 36 pct elonga¬tion in a 30 mm-ga. length. Creep is also an important phenomenon

Jan 1, 1948

By H. W. Rogers

The first steam shovels used in this country were built by the Otis Company, of Boston, about 50 years ago, but as they were of very crude construction and rather unsuccessful only a few were built. For possibly 10 years prior to 1884 successful steam shovels were made and used on certain classes of work, but it was not until that time that they were manufactured in quantities and began to play an important part in all classes of excavation. From that time up to the present day there have been gradual but continuous improvements on the original shovel, not only in the mechanical construction, but also in the design of boilers and engines which are best adapted to this class of service. In proposing a change from steam to electric operation we have to deal with a steam equipment which has not only proved its worth but has probably reached its highest stage of development and efficiency. That the electric shovel is a possibility cannot be denied, as at present from 12 to 18 shovels are in operation in this country. These shovels may be divided into three classes: the friction electric, which is operated by a single constant-speed motor with friction clutches; the three or four motor direct-current equipment, and the three or four motor alternating-current equipment. It is the second and third classes that I wish to deal with, as the first class does not compare favorably with the steam shovel so far as speed is concerned, although it may be operated as cheaply. There is probably no other class of machinery that presents a duty cycle as severe as that of the shovel, which is very short, varying from 7 to 12 sec. on the hoist, from 7 to 12 sec. on the thrust, and from 10 to 18 sec. on the swing, making a complete cycle in from 17 to 30 sec., and the motor to meet these requirements must have a sufficiently low armature inertia to permit of rapid acceleration and quick reversals under small power. It should also be a motor of rugged design, as it must be subjected to severe overloads and shocks and frequent reversals. This is especially true of the hoist motors and, to a lesser degree, of the swing motor; the thrust motor being practically stalled during the digging operation, although it may revolve or overhaul, according to conditions, and is operated at full speed only after the hoisting operation is completed.

Jan 1, 1915

By T. W. Bossert

MELTING is the initial step in the fabricating of all aluminum and aluminum-alloy products. Its function may be considered as threefold: to improve the metal quality, to adjust the composition, and to change the form to that required for subsequent fabrication. Because the melting operation is generally somewhat removed from the final product fabrication, its importance is frequently overlooked. Melting equipment and melting procedures can reflect materially on fabricating procedures as well as on quality and cost of final product. The selection of equipment and the establishment and control of melting procedures, therefore, should be given careful consideration. It is the purpose of this paper to present the various factors that should be considered in establishing melting procedures and in selecting melting equipment. Certain of these are the result of the inherent characteristics of aluminum and can be treated rather specifically. Others depend on the particular production requirements and hence will have to be considered more generally. This paper is intended to cover only the melting of solids, as differentiated from fines, such as borings, turnings, and sawdust. The melting of fines, in many respects, is a subject that should be treated by itself, and practices for melting fines are by no means as standardized as are those for melting solids. The melting of fines is today the subject of considerable developmental interest; hence practices discussed today may soon be replaced by new or improved ones. CHARACTERISTICS OF THE METAL THAT AFFECT MELTING Aluminum and aluminum alloys possess several inherent characteristics that affect the melting problem. Of the physical properties, density, heat content, thermal conductivity, emissivity, and melting temperatures are important because of their effect on equipment design. A list of such properties for commercially pure aluminum is given in Table r, compared with similar properties for iron and copper. The low density of aluminum as well as of the aluminum alloys is of material advantage in the design of melting equipment, in that such equipment can be considerably lighter than similar equipment for handling the heavier metals. The density, however, particularly of the molten metal, is not greatly different from that of the oxides and other nonmetallic materials that develop or become part of the melt during the melting process. Separation of such nonmetallics is not as rapid a process as with some of the other metals, and consideration of this must be made in establishing melting procedures. Sufficient holding time to permit such materials to separate out and, in some cases, fluxing treatments to aid the separation, are required. Since some of these nonmetallics settle to the bottom of the melt, provision should also be

Jan 1, 1946

Most of the production of germanium in the U. S. is from byproducts of smelting Tri-state zinc ore. Only in England has commercial manufacture been reported from coal.

Jan 1, 1953

By Eugene Guccione

Fear of inflation is one important reason for the rebirth of interest in the stock market, and natural resources are the best investment in an era of rapid inflation.

Jan 6, 1976

By William A. Prichard

After a study of the excellent geological reports and maps prepared by the United States Geological Survey,? and after practical experience in working the ore-deposits in this field,

Jan 1, 1904

By Anwar-ul Karim

In one of our recent papers, Cheng, Karim, Langdon, and Dom1 analyzed the creep mechanisms in a Fe-4 pct Si alloy. The experimental results of apparent ac-

Jan 1, 1970

By U. C. Tainton

IN reviewing progress in zinc metallurgy during the last year or so one is reminded of the premise on which H. G. Wells based his "Food. of the Gods," namely that growth does not and cannot take place smoothly and steadily, but occurs in a series of bursts and intermissions: "It is as if every living thing has to accumulate force to grow, grows with vigor only for a time, and then has to wait for a space before it can go on growing again."

Jan 1, 1937

By H. Foster Bain

AFTER all, mineral sanctions are not a measure of peace, they are a measure of war, and we must regard them as such. We have had two examples now in the world-first, Italy, and secondly, Japan-where we have applied sanctions. When we got ready to apply sanctions to Italy that would hurt, they went to war. In the Far East, when we applied sanctions against Japan, in the latter part of 1941, there was a quick reaction, and the Japanese bombed Pearl Harbor.

Jan 1, 1944

By AIME AIME

EVER since Henry Bessemer, nearly 100 years ago, developed the steelmaking process that bears his name, occasional variation has been noted in the quality of steel made in the acid converter, owing largely to the difficulty of stopping the ? refining-which takes only ten to twelve minutes -at precisely the right moment. Principally as the result of this, the amount of Bessemer steel made in the United States gradually declined over the years until it is now about 7 per cent of the total.

Jan 1, 1943

[AARONSON, E.: Discussion on Recent Developments in Fractionation as Applied to Tube Still Distillation, G26, 418 Abbe. See Microscope. Abbe apertometer, 95, 16 ABBOTT, W. L.: A.S.M.E. president, M26,113 biography, M26,113 ABORN, R. H.: Discussions: on Effects of Columbium in Chromium-nickel Steels 113, 159 on Pure Iron and Allotropic Transformations 84, 342 on Prevention of Intergranular Corrosion, 100,329 ABORN, R. H. AND BAIN, E. C.: Discussion on Widmanstätten Structure in Ironcarbon Alloys 105, 252]

Jan 1, 1936

The first National Industrial Conference was disbanded without accomplishing the results hoped for. A second conference is to be called in the near future. In response to suggestions of members of the Founder Societies, the following telegram was sent, Oct. 29, to the President and each member of his cabinet. "Engineering Council respectfully recommends appointing on new Industrial Conference two or more engineers familiar with industrial problems. Council represents five national societies of professional engineers having forty-one thousand members. Washington office in McLachlen Building."

Jan 12, 1919