Search Documents

By C. L. Shapiro, R. Schempp

DuRing the past few years, general interest in the steel-producing and steel-consuming industries has been centered on the so-called "inherent characteristics" of steels. While often vaguely described, these characteristics are known to influence the response to heat-treatment and the hardening characteristics of the material. Although most of the recent papers and discussions have associated the "inherent characteristics" with the austenitic grain size and emphasized the importance of it, comparatively little is known of the variables that may affect the size of the austenite grain. The work to be described in this paper was carried out during the course of a study on the inherent characteristics of tool steel containing one per cent carbon. The discrepancies encountered in the determination and classification of the austenitic grain size led to an investigation of some of the variants influencing the austenitic grain size as determined by standard methods. Methods of Determining Austenitic Grain Size The present methods used for the determination of the austenitic grain size may briefly be classified in two groups: 1. Etching at room temperature to reveal the austenite grain size prior to cooling. 2. Etching at elevated temperatures, cooling to room temperature, and observing the structural conditions that existed at the temperature from which cooling occurred. The outstanding methods of the first group are: (1) the McQuaid-Ehn test, (2) optimum rate of cooling, (3) quenching and etching. McQuaid-Ehn Test.—This established and accepted test does not need much elaboration. It consists of pack carburizing at a definite temperature for a standard period of time and slowly cooling in the furnace. The temperature is 1700" F. (925' C.) and the time is 8 hr. The interpretation and evaluation of this test are fairly well defined in the A.S.T.M.

Jan 1, 1937

By John Griffen

THEORY HYDRAULIC classification as explained by Rittinger and others was largely restricted to conditions wherein the free-falling velocities of the particles were conceived as governing the separations effected (see chapter 9). The laws governing classification under free-falling conditions have been summarized by Chapman and Mott as follows: 1 Nomenclature r represents, in a particle of irregular shape, the round-hole screen through which the particle would pass, or some other linear dimen¬sion of the particle equivalent to d, the diameter of a sphere. s, the specific gravity of the particle. 1, the specific gravity of the water used as a medium. K, a constant. W, the velocity of the water. In an Upward Current of Water 1. A particle will move upward if [W > KVr(s-1)] and, by suitably regulating the speed of the water current, the larger and heavier particles may be made to fall downward against the current, leaving the smaller, lighter particles in suspension in the current. 2. Particles such that [T1= s2-1] cannot be separated in an upward-current classifier with any one velocity of current. Coal particles having a specific gravity of 1.35 cannot be separated from refuse particles of 2.5 sp. gr. Unless 2.5-1 the ratio of diameters is less than [1.35-1 or 4.3 to 1,] and the raw coal must be screened to size limits within this ratio if they are to be separated. Cone¬-shaped vessels or vessels of other shapes that allow the use of&apos; different velocities of current at different points in the flow are used to modify this limitation. 3. During the initial stages of motion, coal particles ascend more rapidly than refuse particles of the same size. 4. A particle will ultimately fall if [W < KVr(s-1).] If particles of

Jan 1, 1950

By B. S. Butler

The principal ore deposits of Arizona are in the southern, cen-tral, and western portions of the state, which physiographically are part of the Basin and Range province, southwest of the Colo-rado Plateau (Pl. I). The Basin and Range province is characterized by numerous subparallel mountain ranges separated by plains or valleys. Most of these ranges trend northwest to north, parallel to the margin of the Colorado Plateau; but in southeastern Arizona, southern New Mexico, and northeastern Sonora, they trend northward, transverse too the edge of the Plateau. The mountains rise abruptly from plains or valleys, the margins of which in many places are pediments cut on hard rock. Some of the plains form closed basins (bolsons, playas), but most of them are drained. The Basin and Range province in Arizona is divisible into the Mountain Region and the Desert Region4 (Pls. I and II). The Mountain Region forms a belt 60 to 100 miles wide that contains most of the large ore deposits. Its longest range measures about 55 miles, the widest 20 miles, and the highest peak more than 10,000 feet above sea level or 7,000 feet above adjacent valleys or plains. Broad plain-forming valleys are exceptional, but several with maximum widths of 20 to more than 30 miles appear in the southeastern portion. In the Desert Region the mountains are relatively low, narrow, serrated, and steep, with sharply angular profiles. There are a few exceptionally large ranges of which the longest measures nearly 100 miles and the widest 18 miles. The highest peak is some 7,000 feet above sea level, and the maximum local relief amounts to about 5,400 feet. Broad and comparatively low desert plains form 50 to 75 per cent of the area.

Jan 1, 1939

Discussion of the paper of Norman B. Braly, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1881 to 1906. GEORGE A. PACKARD, Butte, Mont.:-I would like to ask Mr. Braly if he has any information as to the relative efficiency of the sinking pump, using it as he refers to it, discharging the exhaust into the water column or otherwise. MR. BRALY :-I have never gathered any information on that point. It is a question of getting the work done. In driving the shaft, using that method, we find it easier on the men and everything else. In the bottom of the shaft, if you exhaust back into your column, it is a quiet. shaft. Another thing is the freezing: if you are sinking with air in your pump, you will find it is liable to freeze, and in that case as the air is still under compression it will not freeze the pump. The difference is very small if there is any. But, as might be expected, the pump is a little less efficient when exhausting the air into the column. MR. PACKARD :-I suppose all of us know what a pump in the bottom of the shaft is. My experience has been, although I have no figures, that the capacity of a pump is quite considerably decreased if you are pumping, say, from a depth of 200 ft. through a No. 7 Knowles pump, when you exhaust the air into a column, but, on the other hand, it is also my impression that we can raise the water to a little greater distance. I would like to get some figures from somebody who has made actual tests.

Jan 11, 1913

EVERY English-speaking mining, engineer or geologist knows that some terms used by his profession are not rigid but vary regionally; for example: what is called a vein by some, is called a lode by others and is known as a reef to their Australian colleagues. There are parallels in, the German language. Since, in addition, the meaning of some words may change considerably in 450 years-and other words may disappear completely-and not only the terminology but the concepts of a science are subject to drastic changes over such a long period of time, translating the Bergbüchlein posed some interesting problems. Old German texts and glossaries such as C. T. Delius&apos; Anleitung zu der Bergbaukunst (1773), Minerophilus&apos; Neues and Curieuses Bergwercks-Lexicon (1730), and H. Veith&apos;s Deutsches Bergwörterbuch (1871) proved useful sources of information when defini¬tions of obscure terms were needed. The task of translating was made even more challenging by the author&apos;s personality. As Ulrich Rülein von Kalbe was primarily a physician, his information must have been mostly secondhand. Since the nomenclature of the miners of Saxony, where he gathered his material on silver ores, undoubtedly varied from that of the German miners in Hungary, for instance, who probably supplied him with data on gold ores, it is not astonishing that he is not consistent in his use of some expressions. To give an example: there is every indication that Flöz and schwebender Gang (see footnote p. 21) are used interchangeably in spite of his occasional disapproval of such usage. It is obvious that he was an educated man with a questing and active mind and, although he apologizes-not wholly sincerely, one might suspect-for the simple

Jan 1, 1949

The Development of Research and Quality Control in the Modern Steel Plant. By Leo F. Rein-artz. (Metals Technology, April 1943) Blast Furnace and Raw Materials Essential Considerations in the Design of Blast Furnaces. By A. L. Foell. (,Metals Technology, December 1942) Results Obtained from Surveys of Gas at Furnace Tops. By James M. Stapleton. (Metals Technology, January 1943) Physical Aspects of the Dust Catcher, Gas Washer and Precipitator on No. 3 Furnace at Carrie. By C. P. Clingerman and C. J. FleiscH. (Metals Technology, January 1943) Slag Control by Introduction of Flux through Blast-furnace Tuyeres. By Carl G. Hogberg (Metals Technology, January 1943) The Electrical Conductivity of Molten Blast-furnace Slags. By A. E. MaRtin and GerRard Derge. (Metals Technology, August 1943) Some Physical Characteristics of By-product Coke for Blast Furnaces. By CEarles C. Russell and MichaeL Perch. (Metals Technology, December 19+2) Pyrometry at the Coke Oven. By Robert B. Sosman. (Metals Technology, December 1942) Calcination Rates and Sizing of Blast-furnace Flux. By T. L. Joseph, H. M. Beatty and Gust Ritsianes. (Metals Technology, December 1942) The Low-temperature Gaseous Reduction of a Magnetite. By M. C. Udy and C. H. Lorig. (Metals Technology, October 1942) Steelmaking Problems of Total Operation in Steelmaking. By William C. Marshall and Frank G. Norris. (Metals Technology, April 1943) Silicon-oxygen Equilibria in Liquid Iron, By C. A. ZapFFe and C. E. Sims. (Metals Technology, September 1942) Equilibria of Liquid Iron and Simple Basic and Acid Slags in a Rolating Induction Furnace. By C. R. Taylor and John Chipman. (Metals Technology, September 1942) Rapid Analysis of Oxygen in Molten Iron and Steel. By Gerhard DeRGe. (Metals Technology, January 1943) Silver Chloride as a Medium for Study of Ingot Structures. By Karl L. Fetters and Margaret Dienes. (Metals Technology, August 1943)

Jan 1, 1943

A GREAT labor, surely, is that of the coppersmith, since his every work must be hewn from the mass of copper by force of the hammer. At the beginning, middle, and, end all his works are inconvenient pieces and unpleasant to handle. If the work is done on the forge with the fire, it is done in order to refine or compose it into masses again, for drawing these out while hot with the blows of some heavy hammer, or in order to put the works in a condition that allows them to be drawn out while cold and worked. In this he puts all his labor and industry. He who works at this art often makes use of large hammers, sometimes of small ones, and sometimes of those that have a long iron head and a short handle. With these he is obliged ever to proceed in one of these activities, either extending the work lengthwise, narrowing it, or widening it. This is achieved by the manner and direction of striking and therefore it is sometimes hammered on the inside, sometimes on the outside, sometimes with the peen, and sometimes with the flat head. For instance, when he wishes to close it up he strikes it on the outside with the peen, and if he wishes to widen it he strikes it on the inside with either the flat head or the peen. In this way he proceeds to shape it with constant patience, and to make all the vessels that he works graceful. This metal, as I have told you, is soft, flexible, and tenacious under the hammer. It yields with a certain toughness, provided, however, that it is fine and without admixture of a trace of tin or other metal. That craftsman is a good master of this art who best makes every desired work

Jan 1, 1942

By A. B. Parsons

PUBLICATION of this little volume is a luxury that the Institute itself could scarcely afford. In truth, no engineer nor geologist, no assayer nor metallurgist would be likely to enhance his knowledge, improve his technique, or cut his own operating costs by reading this excellent translation of two booklets first published circa A.D. 1520. It is doubtful if the present enterprise would, in a practical or tangible way, "promote the arts and sciences connected with the economic production of the useful minerals and metals." And such, is the prescribed purpose for which the funds of the Institute should be spent. Fortunately for the Institute, the Seeley W. Mudd Memorial Fund is not so circumscribed; and the Fund Committee enjoys, greater liberty of action. The sponsorship by the Mudd Fund in 1942 of the publication of The Pirotechnia of Vannoccio Biringuccio, as translated by Dr. Smith and Mrs. Gnudi, was an innovation-indeed something of an experiment. Not only was the content of the volume significant mainly for its "cultural" and "scholarly" attributes; -but the format, an outstanding example of the fascinating art of bookmaking, bore no resemblance to the ordinary technical book. The Committee, frankly, was surprised at the enthusiastic reception accorded the volume. When a second edition was required, the Committee became convinced that the publication of material of this type, particularly if printed and bound in attractive form, was an appropriate avenue for utilizing a moderate proportion of the monies available from the Fund. The Bergbüchlein and the Probierbüchlein antedate by some years the first publication of De la Pirotechnia and of De re Metallica; but Georgius Agricola, the author of the latter work, made good use of the material in the earlier volumes. As pointed out in the Introduction, both

Jan 1, 1949

Owing to circumstances which are entirely unavoidable, the cost of rendering to Institute Members the services which they have been ac-customed to expect from the Institute has increased enormously, especi-ally during the past year. The cost of printing has increased 20 per cent. and another 30 per cent. is expected. There is no recourse; the Institute must pay this or cease publishing. The increase for supplies and office force will be very great. Justice to our employees, whose cost for living expenses has risen by leaps and bounds, demands an increase in. wages, wholly aside from the fact that the employees need not and will not stay. The Institute is, therefore, faced with the alternative of greatly re-ducing its service to the members or else of asking from them a small increase in clues. An amendment to the Constitution has been offered by the members increasing the clues to $15 per year, which cannot become effective until 1921. This still leaves us as the engineering society with the lowest annual clues, except only one, whose dues are $15 per year. To help meet the immediate emergency, the Directors have exercised the authority vested in them by the Constitution and By-Laws and requested the members to pay $3.00 for the Transactions to be issued during the year 1920, which is very much less than the cost of publication. It is the opinion of the Board that the members will prefer to pay this slightly additional expense rather than to have the Institute take a backward step in respect to the services which it is rendering, and which has been increasing constantly in amount, as well as in unit cost, during the past seven or eight years.

Jan 12, 1919

The Colorado Scientific Society, Denver, Colo Charles Henderson, President, 519 U. S Custom House, Denver, Colo. Beginning in 1882, up to. about 1919, the Society published 11 volumes containing many valuable papers From the informa¬tion at hand, the papers in those volumes are now only available in libraries or on file at institutions. Vols 12 and 13 are the current volumes, and the list of the geologic papers contained in them are given here For any information as to price and availa¬bility, address the above. Vol 12 (1929-31) No 1, The geology of the Sangre de Cristo Mountains, by J H Johnson, 2, Relation of the ore deposits of the southern Rocky Mountain region to the Colorado Plateau, by B S Butler; 3, Mosquito Range and the Leadville district, by C H Behre, Jr , 4, Geologic history of the Front Range, by T S Lovering, 6, Revision of geologic structure and stratigraphy in the Ouray district, by W S Burbank, 7, Localization of ore in the schists and gneisses of the Mineral Belt of the Front Range, by T. S. Lovering, 8, Relation of the ore deposits of the southern Rocky Mountain region to the Colorado Plateau, by J. B. Tenney; 9, Preliminary geologic map of the Alma mining district, by Q D. Singewald and B S Butler, 10, The Climax molybdenum deposits of Colorado, by B S Butler and J W. Vanderwilt, 12, Localization of ore bodies at Rico and Red Mountain, by G. F Collins, and Geology of Mount Lincoln and Russia mines, by Q D Singewald and B S. Butler. Vol 13 (1932- ): No. 1, Preliminary geologic notes on Galena Mountain, by J. W Vanderwilt, and High plains of Colorado and New Mexico (Late Tertiary history), by F. M. Van Yuyl and J M. Coke

Jan 1, 1933

J. S. UNGER, ? Pittsburgh, Pa. (written discussion ?).-Firebricks intended for, the same purpose, but supplied by different manufacturers, may be of entirely different clays, contain different proportions of flint, calcined and plastic clays; the particles may vary widely in size; the water used to make the brick will vary; the pressure in molding will vary, depend-ing on whether the brick is hand made or power pressed; and the degree of burning in the same kiln will differ. These variables affect the melting point and the strength of the brick when heated. An important property, of a firebrick is its ability to resist heat and, at the same time, weight or load without serious deformation. The soft-ening point and the melting point of a firebrick may be several hundred degrees apart, and two bricks may show considerable difference in their softening points, but the melting points may be approximately the same. Bricks are not usually employed at temperatures close to their melting points. If they must withstand very high temperatures, the firebrick is discarded and a brick of more refractory material is used. Under these conditions&apos; it is doubtful whether the determination of the melting point of a brick has much practical value. If the determination of the melting point is necessary, the test should he made on a portion of the original brick and not on a specially prepared sample. A small triangular pyramid with a base about 1 1/2 in. and 3 in. high can be sawed from the corner of the brick with a thin-bladed car-borundum wheel, without injuring or destroying the size of particles, the bond, or degree of burning of the original brick. This specimen can then he compared with standard Seger cones or tested by any other method desired.

Jan 12, 1919

The Development of Research and Quality Control in the Modern Steel Plant. By Leo F. Rein-artz. (Metals Technology, April 1943) Blast Furnace and Raw Materials Essential Considerations in the Design of Blast Furnaces. By A. L. Foell. (,Metals Technology, December 1942) Results Obtained from Surveys of Gas at Furnace Tops. By James M. Stapleton. (Metals Technology, January 1943) Physical Aspects of the Dust Catcher, Gas Washer and Precipitator on No. 3 Furnace at Carrie. By C. P. Clingerman and C. J. FleiscH. (Metals Technology, January 1943) Slag Control by Introduction of Flux through Blast-furnace Tuyeres. By Carl G. Hogberg (Metals Technology, January 1943) The Electrical Conductivity of Molten Blast-furnace Slags. By A. E. MaRtin and GerRard Derge. (Metals Technology, August 1943) Some Physical Characteristics of By-product Coke for Blast Furnaces. By CEarles C. Russell and MichaeL Perch. (Metals Technology, December 19+2) Pyrometry at the Coke Oven. By Robert B. Sosman. (Metals Technology, December 1942) Calcination Rates and Sizing of Blast-furnace Flux. By T. L. Joseph, H. M. Beatty and Gust Ritsianes. (Metals Technology, December 1942) The Low-temperature Gaseous Reduction of a Magnetite. By M. C. Udy and C. H. Lorig. (Metals Technology, October 1942) Steelmaking Problems of Total Operation in Steelmaking. By William C. Marshall and Frank G. Norris. (Metals Technology, April 1943) Silicon-oxygen Equilibria in Liquid Iron, By C. A. ZapFFe and C. E. Sims. (Metals Technology, September 1942) Equilibria of Liquid Iron and Simple Basic and Acid Slags in a Rolating Induction Furnace. By C. R. Taylor and John Chipman. (Metals Technology, September 1942) Rapid Analysis of Oxygen in Molten Iron and Steel. By Gerhard DeRGe. (Metals Technology, January 1943) Silver Chloride as a Medium for Study of Ingot Structures. By Karl L. Fetters and Margaret Dienes. (Metals Technology, August 1943)

Jan 1, 1943

By J. D. Mooney, D. L. Darnell

The accompanying chart has been drawn for the convenicncc of engineers as&apos; a means of quickly determining the correct number of plies of conveyor belts operating under specific conditions. The calculations are based on the average safe strength (factor of safety, 15) of the various standard rubber conveyor belts. The calculations assume maximum loading conditions; that is, the belt is considered as carrying the greatest load that it will handle without spillage at ordinary belt speeds. This not only produces the most economical operating conditions, but also the maximum tension in the belt. The chart is a graphical representation of the formula: Where, p = kg W(L + 10H) p = the correct number of plies k = a constant, depending on the type of drive g = the weight &apos;in pounds per cubic foot of material handled W = the width of the belt in inches L = the length of the belt in feet (approximately twice the center distance). H = the difference in elevation between the head and tail pulleys, in feet. For a simple drive, with a bare pulley, k = ----1 For a simple drive, with a rubber-lagged pulley, k = --- 1 For a, tandem drivej with bare pulleys, k = 1/375.000 For a tandem drive, with rubber-lagged pulleys, k = ---1 The chart is drawn for a simple drive, with a bare pulley (k — =e)1 ; therefore, the number of plies obtained from the chart should be multi- &apos; plied by the factor 0.83 or 5/6 for simple, lagged drive; the factor 0.67 or 2/3 for tandem, bare; and the factor 0.55 or 11/20, for tandem, lagged. The formula p = kgW(L + 10H) has been developed mathematically

Jan 1, 1916

By A. B. Parsons

This YEAR BOOK, which is sent to every member, contains the roster of officers and the principal standing committees, brief summaries of the proceedings of the Annual Meeting and of the Regional and Divisional meetings, and the necrology for the year 1934. Also are included abstracts of papers published during the year and a classified list of TECHNICAL PUBLICATIONS and CONTRIBUTIONS, as well as an index of all material published by the Institute in 1934 in TRANSACTIONS, in TECHNICAL PUBLICATIONS and CONTRIBGTIONS and in MINING AND METALLURGY, the monthly magazine, the twelve issues&apos; of which contained 98 technical papers Thus 111 small space are gathered together references to all papers, magazines and books printed by the Institute during the year. The papers for the Iron and Steel and Institute of Metals Divisions have been issued as TECHNICAL PUBLICATIONS distributed under the binding of METALS TECHNOLOGY in the months of January, February, April, June, August, September, October, December This plan of distribution will be continued in 1935 for these two groups The publications for the year 1934 include two sponsored by the Institute&apos;s special funds. A Manual for Student Associates and Affiliated Student Societies, prepared by the Committee on Student Relations, of which Jay A. Carpenter was Chairman, was published through the courtesy of the Seeley W. Mudd Memorial Fund, and Volume 112 of the TRANSACTIONS, on Milling Methods, assembled by the Committee on Milling Methods, of which Charles E. Locke was Chairman, was financed by the Rocky Mountain Fund The remaining volumes were all TRANSACTIONS, Volumes 107, Petroleum Development and Technology; 108, Coal Division; 109, Metal Mining and Nonmetallic Minerals; 110, Geophysical Prospecting; 111, Institute of Metals Division and 113, Iron and Steel Division

Jan 1, 1935

By Edward H. Robie

Engineers&apos; Centennial THIS summer, in Chicago, will be celebrated the "Centennial of Engineering" and half a hundred engineering societies will have meetings of one kind or another in the two weeks following Labor Day. It is really the 100th anniversary of the founding of the American Society of Civil Engineers. Centennial of Engineering is merely a convenient label to put on the celebration of 100 years of engineering progress in this country since the ASCE was founded. Engineering, of course, is much older than is thus indicated-thousands of years older. But Americans have a penchant for dramatizing progress by celebrating assumed anniversaries. Four years ago a special 30 stamp was issued on which a Brahma chicken was prominently displayed, with the legend, "1848-1948. Centennial of the American Poultry Industry." We feel reasonably sure that the first dozen eggs was sold considerably earlier than that. Until a hundred or so years ago engineers were generally classified as either military or civil. Apparently a group of civil engineers met for the first time in Augusta, Ga. but no records were kept and the first meeting of which we have definite knowledge was at Barnum&apos;s Hotel in Baltimore, Feb. 11, 1839. Forty engineers were present and they decided to form a society. Among the aims of these engineers was "the greatest amount of useful effect at the smallest cost," which is as good a slogan for the engineer of today as it was 113 years ago. It was mentioned that the existence and prosperity of the society depended in no small degree on "the personal conduct and exertions" of the members. "Talents and respectability are preferable to numbers ... from too easy and promiscuous ad mission, unavoidable, and not infrequently incurable, inconveniences perplex most societies."

Jan 1, 1952

ABIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has three major awards to make annually and one special prize for excellence in technical papers, as follows. The Robert W. Hunt Medal and Prize, The J. E. Johnson, Jr., Award, the James Douglas Medal, and The Lewisohn Platinum Prize to senior members. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting&apos; ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules ? 1 The award shall consist of two prizes, first of a gold medal, second of a sum of money, a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt&apos;s main contributions to the industry have been in the improvement of production and quality of material

Jan 1, 1923

The Institute makes liberal provision for inclusion of engineering students through individual Student Associate membership. Such members pay $2 per year, receive MINING AND METALLURGY, may purchase Technical Publications at reduced rates, have the privilege of attending all meetings and are furnished a distinctive badge in the form of a watch fob. Provision is also made for the affiliation of organized student societies in recognized schools of engineering chemistry, geology and related sciences. In order to qualify for affiliation it is not necessary that all members of the society become Student Associates since the individual members of the society are not listed as members of the Institute However, a large majority of the members of many of the societies are also Student Associate Members of the Institute. Among the things that the Institute does for the affiliated societies are the following: (a) A copy of each issue of MINING AND METALLURGY is furnished to the society; (b) Reports of the meetings and activities of the society are reported in MINING AND METALLURGY; (c) Assistance is given by the Institute in obtaining speakers for the meetings of the society; (d) The name of the society and of its officers is listed in the annual Directory and other publications of the Institute; and (e) Members of the society are given the use of the Engineering Societies Employment Service. Student organizations, desiring to be recognized as affiliated student societies of the Institute, should make application to the Secretary, giving particulars as to the nature of their organization, of their membership, and their officers. The accom¬panying list on page 24 gives the names of the affiliated student societies, their presi¬dents and their secretaries, as of April 17, 1931.

Jan 1, 1923

The Institute makes liberal provision for inclusion of engineering students through individual Student Associate membership. Such members pay $2 per year, receive MINING AND METALLURGY, may purchase Technical Publications at reduced rates, have the privilege of attending all meetings and are furnished a distinctive badge in the form of a watch fob. Provision is also made for the affiliation of organized student societies in recognized schools of engineering, chemistry, geology and related sciences. In order to qualify for affiliation it is not necessary that all members of the society become Student Associates since the individual members of the society are not listed as members of the Institute. However, a large majority of the members of many of the societies are also Student Associate Members of the Institute. Among the things that the Institute does for the affiliated societies are the following: (a) A copy of each issue of MINING AND METALLURGY is furnished to the society; (b) Reports of the meetings and activities of the society are reported in MINING AND METALLURGY; (c) Assistance is given by the Institute in obtaining speakers for the meetings of the society; (d) The name of the society and of its officers is listed in the annual Directory and other publications of the Institute; and (e) Members of the society are given the use of the Engineering Societies Employment Service. Student organizations, desiring to be recognized as affiliated student societies of the Institute, should make application to the Secretary, giving particulars as to the nature of their organization, of their membership, and their officers. The accompanying list on page 21 gives the names of the affiliated student societies, their presidents and their secretaries, as of April 16, 1933.

Jan 1, 1932

By Harry Seltz, J. C. DeHaven

InteRmetallic compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dissociated in the liquid state, as indicated by the continuous form of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455&apos; C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a = 6.52, b = 8.60, c = 4.16 A.&apos; There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO² = CdO + CO + Sb From the known free energies of formation of CdO, CO² and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell reaction is the reversible formation of the compound from the elements. The first method is generally applicable, but requires elaborate experimental equipment. The second method can not be used for compounds melting at low temperatures, owing to the difficulty in establishing equilibrium. The electromotive force method, therefore, seemed to offer

Jan 1, 1935

Present indications are that the Fourth National Exposition of Chemical Industries, to be held in Grand Central Palace, New York, Sept. 23 to 28, will be the greatest exhibition of its kind ever held. Preparations are well under way and the advisory committee is working hard to make, every department of the affair a success. Men prominent in the chemical and allied industries will speak on subjects vital to present conditions and needs. Dr. C. H. Herty, and Dr. G. W. Thompson, President of the American Institute of Chemical Engineers, are to make opening addresses. F. J. Tone, President of the American Electrochemical Society; Dr. W. H. Nichols, President of the American Chemical Society, and several others, are expected to make addresses also. Prof. Joseph W. Richards will speak on : ?Ferro-alloys of silicon, tungsten, uranium, vanadium, molybdenum, and titanium." Theodore Swann, President of the Southern Manganese Corporation will speak on "Ferro-manganese." The program for the exposition is in active preparation. There will be a series of symposiums on the "Development of Chemical Industries in the United States, notably since July, 1914." Among other topics for consideration is that of potash development; C. A. Higgins, of the Hercules Powder Company, will speak of the operations of that company in the recovery of potash from kelp; Linn Bradley, of the Research Corporation, on its recovery from cement dust, and other sources, by electrical precipitation. Other symposiums will be devoted to chemical engineering, acids, industrial organic chemistry, the ceramic industries, and the metal industries. Among the speakers are: A. Hough.-" Chemical Engineering in Explosives: TNT; TNA; Picric Acid; and Nitrobenzol." E. J. Pranke.-" Development of Nitric Acid Manufacture." S. P. Sadtler.-"Development of Industrial Organic Chemistry." Geo. H. Tomlinson.-" Wood as a Source of Ethyl Alcohol." C. A. Higgins.-"Kelp as a, Source of Organic Solvents." Alcan Hirsch.-" Pyrophoric Alloys."

Jan 9, 1918