Search Documents

By K. E. Beu

IN the measurement of retained austenite concentrations in steels using the integrated intensity method,1 Averbach has pointed out" that the absorption factor A(0) for a flat sample making a glancing angle 4 with the incident X-ray beam can be combined with his constant factor R to obtain our constant factor" G provided that "1—There is no preferred orientation in the sample, and 2—The geometric requirements [for the sample, film, and X-ray beam] have been met precisely."' If A(0) can be combined with R to give G according to the equation G = R . A(0) [14] then the possibility for making non-compensating errors in the austenite determination has been eliminated. This has been described previously in a technical note." Because of the brevity of the previous note,3 it was impossible to emphasize the fact that the two conditions on preferred orientation and geometry can be easily met experimentally, contrary to Aver-bach's statement that: ". . . the necessary conditions must be tested experimentally for each determination, and this is done most easily by observing whether the apparent absorption has the form of Eq. 2 [the theoretical equation for A(0)]."" he way in which these two conditions can be met experimentally will be discussed briefly to help clear up this point. In addition to these two conditions, other factors such as sample shape, homogeneity, and grain size which also affect A will be included in this discussion. A (0) depends on sample shape. The theoretical function for A was derived originally for a flat surface.' In general we have found that a flat sample surface is readily obtainable." If such a surface can * The effect of surfaces which are not flat on the measurement of retained austenite will be discussed later. be obtained, it has the following advantages: 1—it is easily reproducible from sample to sample, 2—it is the form required for metallurgical examination —this type of examination being frequently desirable for this work, and 3—it is an efficient shape for diffraction purposes. Perhaps the most important of these features is that a flat sample surface is easily reproducible; hence, this requirement on the repro-ducibility of A from sample to sample is met for all such samples. Fig. 1—Schematic diagram of the quartz crystal monochromator diffraction unit. The centerline of the main beam is at 6' to the target face. The tangent to the crystal face is at 16.8' to the moin beam. The centerline of the monochromatic beam is at 33.6 to the main beam. The sample surface can be rotated in its own plane. The angle of the sample surface and the monochromatic beam can be adjusted by rotating about the vertical axis, The film holder can also be rotated about B so that the film can be exposed over the desired angular range. For Fe K, X = 1.932A. 1011 planes of quartz have d = 3.35A. A(0) depends on homogeneity and grain size. If the sample is badly segregated or the grain size is large, the effect of micro-absorption and primary extinction1. ' must be considered. It has been shown, however, that for most plain carbon or low alloy hardened steels, neither micro-absorption nor primary extinction effects are present.' A (0) depends on camera geometry. For a given angle 0, A remains theoretically constant from a geometrical viewpoint only if the following factors are kept constant: 1—the angle of inclination .+ of the sample to the X-ray beam, and 2—the centering of the sample with respect to the film cylinder. These are mechanical problems which can be solved readily if the facilities of a good machine shop are available. The arrangement used to insure that the angle 4 remains constant and the centering of the sample is reproducible is indicated schematically in Fig. 1. The sample is clamped against a thin plate with a hole in it by means of a spring-loaded pres-

Jan 1, 1954

By H. R. Crawford, P. B. Crawford, A. F. Tragesser

A method has been developed to calculate wellbore temperatures during mud circulation and the actual cementing operation to aid in the design of cement slurries. The method agrees within 10F with previously measured values. The calculation technique provides temperatures, as functions of time, at varying depths in both the casing and annulus. The technique also provides this information if a relatively cool cement slurry is pumped into the well immediately following circulation of hot mud. Circulating bottom hole temperatures of brine and a bentonite mud were measured. INTRODUCTION As wells are drilled deeper, greater demands are being made on all phases of the industry, and new technology has been developed to provide satisfactory well completions. However, little or no work has been conducted on accurately determining bottom-hole, static and circulating temperatures.. In designing a cement slurry, such factors as density, fluid loss control, viscosity, deterioration from ternperature, compressive strength and pumping time must be considered. Individual well conditions often make it necessary to include still other factors. Pumping time is a primary consideration and, as wells are drilled deeper, encountering higher bottom-hole temperatures, this property becomes even more important. Cement slurries must be designed with sufficient pumping time to provide safe placement in the well; however, the slurry cannot be overly retarded as this will prevent the development of satisfactory compressive strength. The pumping time of a specific cement is currently obtained by subjecting the cement to simulated conditions of temperature and pressure. A reasonably accurate bottom-hole pressure may be obtained by considering hydrostatic heads of fluids, friction pressure and wellhead pressures. However, accurately determining bottom-hole temperatures is much more difficult. Bottom-hole static temperatures are estimated by considering several sources of information, including logging temperatures, published temperature gradient maps and field experience. This information is usually questionable due to disagreement of data from the various sources. Temperature gradient maps were constructed based on temperatures recorded many years ago while running bottom-hole pressure tests. These thermal gradients then represent an average of well conditions and cannot always apply to a specific well. Also, logging temperatures may be affected by the time since fluid was last circulated, rate of penetration, circulating rate and many other factors. Therefore, even though logging temperatures are available, the question still exists as to the correction factor that should be applied to obtain an accurate static temperature. After obtaining static bottom-hole temperature, it is then necessary to relate this to circulating temperatures actually encountered by the cement slurry. This is accomplished by selecting a test schedule from the API RP-10B corresponding to the estimated well conditions.' The API-recommended practice for testing oilwell cement provides testing schedules for various well depths and conditions. These schedules are intended to simulate down-hole conditions during cementing. They provide a rate at which both temperature and pressure are increased until the estimated circulating conditions are reached. These testing schedules represent circulating temperatures for an average well and, although there is flexibility in choosing the test schedule that most accurately simulates the temperature of an individual well, it still is not possible to consider all the well conditions that will affect the bottom-hole temperature. Many factors affect cement temperatures; for example, the length of time a well has remained static prior to running casing and cementing, the circulation time, the temperature of fluids used in cementing, fluid density and flow properties of fluids. The pumping time for a typical retarded cement could vary from 2 to 4 hours with a 10F change in testing temperature. Variations in pumping time are the most critical in highly retarded cements used in deep, hot wells; yet, predicting bottom-hole circulating temperatures is more difficult in these wells. This work was conducted to develop a means of calculating circulating temperatures as a function of well depth, casing and hole size, pumping rate and time, fluid and reservoir physical properties and thermal status of the well. PREVIOUS WORK In 1941 Farris reported on a study to develop information leading to a more practical laboratory evaluation of oilfield cementing mixtures and performance.' It was then recognized that the pressure factor was being neglected,

By John D. Price

COAL blending, in the preparation of coal before coke making, is so commonly practiced as to be almost universal. But the reasons underlying this practice, the benefits resulting from it, and the materials used in blending vary widely. This paper will outline the various phases of the subject and present information which may be correlated with work that has been done elsewhere. It will deal entirely with work done on the high-volatile coking coals of the western part of the United States, special emphasis being given to the coals of Colorado and Utah. A surveyL of the 86 coke plants in active operation in the United States during 1949 indicates that only 9 plants, or 10.5 pct of the total, charged one single rank of coal into their ovens, while the remaining 89.5 pcl made use of blending in some form. This report indicated that of these total plants 5 used straight high-volatile coal, 4 used straight medium-volatile coal, 47 used blends of high and low-vola-tile coals, 25 used blends of high, medium, and low-volatile coals, 2 used blends of high and medium-volatile coals, 3 used blends of medium and low-volatile coals. The fact that certain plants operated on a single kind of coal should not be interpreted to mean that no blending was practiced there, for invariably such plants secure their coal from more than one source and in the interest of uniformity do blend the coals as received. The general term coal blending covers two fields, the first of which is the mechanical mixing of a number of coals to secure uniformity. Often it is found necessary to secure coal for coke production from a number of different mines; these coals, though of the same general type or rank, may differ in their chemical composition or in the physical qualities they impart to coke made from them. Again, it is not unusual to find that coal from different sections of the same mine may show variations in quality. Under such conditions it may be necessary, in the interest of a uniform final product, to introduce a system of blending bins, a bedding yard, or other mechanical methods of securing a uniform mixture. Unfortunately this form of blending has received very little attention up to the present time; it has not received the consideration its value merits. The second type of blending, while also for the purpose of coke improvement, deals more particularly with the use of a blending agent differing in character from the base coal: it is this form of blending that will be discussed here. To consider only the western coals, for blending may be found necessary for other reasons with other coals, blending has been practiced experimentally or commercially under the following conditions: 1—When a single coal or mixture of coals of the same rank does not produce a satisfactory coke. For example, a high-volatile coal when used alone is likely to contract when coked so that a comparatively weak coke is formed. Or, if of very low rank, the coal may be deficient in the necessary bitumens required for good coke production. 2—When a product of some special quality is required, for example, when a plant ordinarily producing blast furnace coke must operate at slow coking rate to produce a high-grade foundry coke. Under this condition the reduced daily production of all products which accompanies slow coking time may be undesirable, and the use of some blending agent to increase the size of coke made at faster coking rates may be necessary. 3—When greater yield of coke or its coproducts is needed. Depending upon economic values of the products it may be found desirable to increase the yield of one or the other. 4—When supply of a particular coal must be used, either to protect reserves of high quality coking coal or to utilize a surplus or inferior product not otherwise usable. Many materials have been used for blending purposes, the exact agent to be used depending both upon the condition to be corrected and the nature of the base coal. No universal blending agent that can

Jan 1, 1954

By P. Martinez, A. F. Hoyte, F. E. Senftle

The possibility of applying a neutron activation technique for silver exploration is considered. A mobile positive-ion accelerator type neutron source is used to irradiate a small area of rock or soil in situ. By using a short period of irradiation and gamma ray spectral analysis, a technique is shown for silver exploration. Two different mobile units are described. Laboratory and preliminary field tests both indicate that a sensitivity of less than 1 oz of silver per ton of ore can be achieved. The increasing consumption of silver for industrial uses and also for coinage has caused a serious shortage of silver in this country. The silver shortage has been reviewed and analyzed by kiilsgaard1 who concludes that, "The best hope for meeting future demands for silver is through accelerated exploration for precious ores." As almost all the exposed "bonanza" type silver deposits evidently have been found, it is urgent that some sensitive geophysical technique be found to detect large, extended, but generally low-grade, secondary ores, as well as hidden vein deposits. Silver is easily made radioactive by exposure to slow neutrons; hence a neutron activation method appears promising for locating silver deposits. The principles of mineral beneficiation using neutron activation techniques were discussed some years ago.2-4 Using the same approach, a preliminary description5 has been published of neutron activation as a mineral exploration tool. An exploration technique is described in which silver is made radioactive in situ and detected with a gamma radiation counter. The technique is similar to the well-known method used for uranium exploration. THEORETICAL CONSIDERATIONS Elemental silver consists of two isotopes, Ag107 and Ag109, having naturally occurring isotopic abundances of 51.4% and 48.6%, respectively. For short periods of irradiation of silver by thermal neutrons, the long-lived 250 day, half-life isotope, Ag110m, is not produced in significant quantities. However, significant quantities of 2.3 min half-life Ag108 and 24.5 sec half-life Agl10 are formed by the following reactions. Ag108 and Agl10 emit a 0.44 Mev (million electron volts) and a 0.66 Mev gamma ray, respectively. Ag107 + n + Ag108 (2.3 min) Ag109 + n + Ag110 (24.5 sec). Because of the large capture cross section (110 barns) of Ag109, and short half-life of Ag110 (24.5 sec), the 0.66-Mev gamma ray is the most prominent emission from silver for neutron activation periods of about a minute's duration.* The 0.44-Mev gamma ray from Ag108 will also be present, but will be one or two orders of magnitude lower in intensity. The decay scheme of Ag110 is shown in Fig. 1. If the neutron irradiation time is limited to about 100 sec, the Ag110 activity will essentially reach saturation and can be used to detect the presence of silver. In a neutron flux of 10 8 neutrons/cm2/set, the induced 0.66-Mev activity in 1 g of silver will be about 2 x 107 disintegrations per sec. This is about 1000 times the measurable gamma activity of 1 g of uranium in equilibrium with all its decay products; hence there is ample activity for detection. Under the same conditions of activation, most of the other elements do not reach this relatively high disintegration rate. Although this is in favor of the proposed technique, other problems must be considered. For mobile operation, it is desirable to obtain the largest neutron flux to weight ratio. Hence we have used a small 150-kev accelerator-type neutron source rather than an isotopic source such as an americium-beryllium neutron source. By use of remote control system, an accelerator-type neutron source can be safely used without the massive shield required for an isotopic source. Moreover, an accelerator-type source is more versatile in that it allows one to use a flux of either 14-Mev or 3-Mev neutrons, depending on whether a tritium or a deuterium target is used. With a 14-Mev generator, one can obtain a flux of 10 9 neutrons/cm 2/sec, and with a 3-Mev generator, the flux is generally two orders of magnitude less. Although silver will become activated with either generator using proper moderation, detection may be

Jan 1, 1968

By V. C. Williams

Some of the physical, chemical, and electrical processes for conversion of saline water to potable or industrial water are economically surveyed from an engineering viewpoint. Since all these processes require energy for drive and equipment for containment, the correlative economic factors are developed which indicate directive influences in the choice of particular regional processes. The supply of natural waters and its distance also affect decision. Any one process will probably not prove dominant in the field because auxiliary considerations such as the saline water source; types and continuing availability of fuel; electric power use or recovery; area economic status and advancement; and the political pressures of population, group demands, and land use tend equivocally to obscure capital and operation cost decisions. Basic engineering considerations, data, and economic factors are presented to assist in the direction of these decisions. An exploding world population, increasing industrialization, advancing standards of living, and the desire of less-privileged nations for betterment focus attention sharply on a major problem: water. *19 Up to now, in retrospect, people have had it relatively easy in the handling of this problem. All the better dams in the most advantageous sites, the better aquifers, the shortest aqueducts have been built. In another phase of the problem, concern is evident that wastes cannot indefinitely be disposed of merely by keeping them dilute and discharging them promiscuously. 7-9 And, perhaps, as past civilizations have done,l5 water, watersheds, streams, and irrigation may have been mismanaged or, at the least, not adequately studied.3,5,36,37 In this last is perhaps the core of the problem. As Gross states, "Ignorance and too often, indifference are contributing factors. Archaeology and theology both furnish ample testimony to the existence of rich lands where deserts now stand; it was man who ravaged his land. Unless education is a companion to water development, development might as well be forgotten. But without water, there is no beginning."13 The U.S. is showing increasing concern about its water for predictions are that by 1980 the daily withdrawals will be 494 billion gal, a figure nearly equal to the dependable supply.Is This is based on a conservative projected population of 230 million. The major categories of withdrawals are: To make available this per capita average of 2150 gal per day will require an expenditure of $219 billion over the next 20 years. The U.S. is not alone in this concern. The United Nations shows as arid zones of the world: all of Africa north of the equator and south of the 20's parallel; all of the Arabian peninsula; all of the middle east and Iran, Iraq, Pakistan, Afghanistan, northern and central India; a great band about 1000 miles wide along the 40'~ parallel from the Caspian Sea east across Russia through China to the Pacific Ocean; all of Australia except the coastal plain; the Caribbean Islands; the western nations of South America; and the western third of the United States and of Mexico. With one quarter of the earth's 57,500,000 sq miles of land thus suffering from lack of good water, increasing attention goes to the treatment of brackish and sea waters. The U.S. has been a leader in this field4,12, 16123,24 through its Office of Saline Water in the Dept. of Interior because even now some of its cities and regions are short of potable water. 11j'7,M Industrial water is also of vital concern as a result of ever higher industrialization1,14122 Other nations, among them JaPan, Israel,13188 Germany, Union of South Africa, Australia, Netherlands, France, Yugoslavia, Russia, and groups such as the Organization for European Economic Cooperation (OEEC)' are also diligent. The objective is low cost water, which means that both technology and economics have prominent roles in saline water conversion processes. TECHNOLOGY: SALINE WATER CONVERSION A number of reviews of methods have been made, principally by staff members of the Office of Saline Water (U.S. Dept. of Interior). Jenkins,31'32 Gillam,34p

Jan 1, 1962

By Cloyd M. Smith

A few years ago, the Ventilation Committee established the practice of resenting one topic each year for discussion at the annual meeting. The practice has met good response on the part of committee members and I suggest that it be continued. The topic chosen for this year, "Underground Anemometry," is a topic which has bothered me for more than 20 years. It seems to me that the coal industry is content to rely on slipshod methods for measuring the rate of flow of air underground, so I prefaced my discussional charge to committee members with the statement that I regard air measnrements made in the usual way, with hand held anemometer, as no good. Agreements and disagreements came in from more than a dozen engineers, some of whom are with operating companies, coal and metal; some with manufacturers; others with government agencies. The statement was accompanied by a questionnaire on the use of the rotating vane anemometer and by one describing two methods of using a mechanically held anemometer. The questionnaire will be considered first. The questionnaire and statement are as shown on pages 5 and 6, the committee members and respondents are given on page 4, and the general comments of the latter on page 5. Questionnaire 1. Has your company or agency issued written instructions for care and use of anemometers? If so, please enclose a copy with reply. Only one answer, McElroy's, was affirmative. It gave reference to Bureau of Mines publications1'5 which recom- mend the hand held anemometer for rough measurements and indicate that am accuracy of 5 pct can be had if calibration and method factors are used. Mathews said that instructions are principally oral while Maize reported that state inspectors of his department are well trained in use and care of anemometers. 2. Are your anemometers calibrated periodically? If so, by their manufacturer? or by? Are calibralion corrections applied to all observed mean velocity readings? Only one respondent, Lee, answered negatively as to calibration. This means that anemometers are generally calibrated but the questionnaire failed to ask how often this is done. As no one volunteered the information, we have no data on this point. In six cases the instruments are sent to their manufacturers for calibration. but Krickovic reports that his company limits manu-facturers' calibrations to anemometers which are used by operating personnel; those used by the engineering department being calibrated by U. S. Bureau of Standards. The Anaconda Copper Mining Co. has its ventilation engineers calibrate its anemometers. Most of the respondents say that a calibration correction is applied to each mean velocity reading, but Krickovic limits this to surveys made by the engineering department. Since Lee does not calibrate, he has no correction to apply. Maize reports that his department has its anemometers calibrated but does not apply corrections. 3. Do your men hold the anemometer by hand in measuring air flow? for 1 min? or traverse the section? for 1 min? or at? points for 5 sec each? Of 10 replies, 6 were "yes," 3 were "no," and one was "seldom" with respect to holding by hand. Among the six hand holders, four hold in a central position in the measuring section for a minute, except that two of them, Krickovic and Matthews, traverse the section by hand for survey or fan test. Their operating personnel hold by hand, centrally, for routine measurements. McElroy sometimes traverses with hand-held anemometer in rapid survey work. 4. If the anemometer is not held by hand, how is it supported? Augustadt supports the anemometer on an adjustable rod, Condon on "a rod of sufficient length to reach all points with observer standing in one position throughout traverse and at arm's length from plane of traverse." I presume that arm's length must be interpreted liberally enough to allow for arm movement, otherwise it would be impossible to manipulate the anemometer throughout the traverse section. Mancha upholds Condon in this method of traversing. Glanville hangs the anemometer on the end of a 4-ft staff by the hasp at the top of the anemometer frame. McElroy mounts it on the end of a rigid square shaft, 12 in. long, the staff being at right angles to the axis of the instrument. He traverses the section in two halves, holding the anemometer 3 feet from his body.

Jan 1, 1950

By J. M. Tobin, L. H. Cadoff, L. M. Adelsberg

The reaction between liquid zirconium and graphite at temperatures above 2000 °C has been investigated. The reaction products were found to be carbon-saturated zirconium metal and ZrC which formed between the graphite and the metal. Parabolic growth behavior was observed for the ZrC Phase at all temperatures of this investigation. The parabolic growth constant at temperatures between 2000° and 2860°C was measured to be 1.83 exp 84,300/RT) sq cm per sec. The reaclion mechanism was proposed to be the rapid carbon saturation of the liquid metal and the formation of ZrC at the metal-carbide interface with diffusion of carbon through the ZrC, the "rate - determining step" of the reaction. The concentration-independent diffusion coefficient of carbon in ZrC, (DZrC), was expressed as 0.95 exp? 78,700/RT) sq cm per sec. This value mas calculated using the temperature-invariant ZrC phase fields proposed in the literature. The [ZrQiq)] — [ZYQiq) + ZrC] phase boundary over the temperature range 2000° to 2800°C was determined and the ZrC + C eutectic temperature was found to be 2890° ± 50°C. ThE Group IV and VB transition-metal refractory carbides are of interest because of their high melting points, high temperature strength properties, and relative inertness in certain corrosive environments. The present-day understanding of these materials, however, is limited by the general unavailability of accurate and reliable physical and chemical property data. This is due primarily to the difficulties associated with the preparation of suitable, high-density, high-purity carbide samples, and the achievement and control of uniform high-temperature environments. Accurate measurement of temperature is also an important factor limiting the reliability of reported data. The Zr-C reaction was selected for investigation because of the high melting point (>34000C) and favorable nuclear properties of the reaction product, ZrC. The direct reaction method afforded an opportunity to obtain kinetic data on the fully dense carbide. In this paper, layer-growth techniques were used to estimate the diffusivity of carbon in ZrC and to investigate the phase equilibria in the Zr-C system at temperatures above 2000°C. EXPERIMENTAL PROCEDURES AND DATA Crystal bar zirconium (99.9 pct Zr), purchased from the Nuclear Materials and Engineering Corp., and ZTA graphite (99.9+ pct) were used in this study. The analyses of the materials are listed in Table I. A schematic of the high-temperature carburization apparatus is shown in Fig. 1. The sample was a zirconium metal charge in a 1/2 -in.-ID graphite crucible which was capped with a tightly fitting graphite stern. The crucible and stem were designed to closely approximate black-body conditions. The graphite crucible was packed in lampblack (outgassed 1 hr at 2100°C) which provided insulation and thermal stability to the system. The inert atmosphere was maintained by a constant flow of high-purity argon or helium gas. The nozzle-diffuser section on the top flange was sufficient to prevent back-diffusion of air into the system. Chemical analysis of the carburized samples revealed oxygen and nitrogen concentrations of less than 44 and 20 ppm, respectively. The sample was heated by induction with a Westing-house 5 kw-450 kc power source. Temperature was measured with a Milletron two-color pyrometer which was sighted into the crucible by reflection from an overhead front surface mirror. Optical losses due to glass absorption and light reflection at air-glass interfaces were minimized by the employment of the dynamic-gas seal. It was found that no correction was required for the front surface reflector. The pyrometer was calibrated periodically against a U.S. Bureau of Standards tungsten ribbon secondary standard. Temperatures inside the crucible were also calibrated against the Zr-ZrC eutectic (1850°C)1 and the Nb-Nb2C eutectic (2335°C)2,3 temperatures and agreed to within ±10°C of these values. The temperature was controlled by manually adjusting the power input; variations of

Jan 1, 1967

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and' is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of' Venezuela. The Welge gas-flood technique,' based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.' The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966

By Jeff Steinhoff

INTRODUCTION The Henderson mine utilizes a highly mechanized, continuous, panel-caving, mining system to extract ore from a deep, massive, molybdenite deposit. The mine is located 80.5 km (50 miles) west of Denver, Colorado. The mine surface facilities are located 3,170 m (10,400 feet) above sea level in a steep valley on the eastern side of the Continental Divide. Milling facilities are 24 km (15 miles) west on the western side of the divide at an elevation of 2,804 m (9,200 feet) above sea level. The ore- body is located approximately 3,000 feet south of the valley under Red Mountain. Access to the ore for men and materials is through a 915 m (3,000-foot) deep, 8.5 m (28-foot) diameter, vertical, concrete-lined, service shaft. Access from the mill is through a 15.5 km (9.6-mile) rail haulage tunnel. The mine is ventilated through an additional intake shaft and two exhaust shafts. Mine production at this time is 27,255 mtpd (30,000 stpd). The mine ventilation system supplies 1,038 cubic meters per second (2.2 million cfm) through approximately 60 miles of drifting or 2.7 tons of air per ton of ore mined. There are 130 fans in the mine in fixed locations and in vent lines with 6,900 connected horsepower in the mine. MINING METHOD AND LAYOUT The orebody is divided vertically into two major zones. The upper zone is the 8100-level production area. The bottom zone is the 7700- level production area which is in the early development stage. The rail haulage level at 7500 feet is common to both production zones. Each mine production zone consists of five associated sublevels. The cave undercut level is 16.8 m (55 feet) above the production level. Two boundary cutoff levels are located 44.2 m (145 feet) and 62.5 m (205 feet) respectively above the production level. The fresh-air level is positioned 15.2 m (50 feet) below the production level, and the exhaust vent level is 19.8 m (65 feet) below the production level. Horizontally, each production zone is divided into three panels each, 224 m (800 feet) wide. These panels are caved from south to north. As the caving in one panel nears completion, caving in the adjacent panel is initiated. Development for the caving panels is continuous so that the sublevels above the production level and the production level itself have a combination of development drifting and production-related activities. UNDERGROUND VENTILATION NETWORK The ventilation system is zoned in the same manner as the orebody itself. One major split of 600 cubic meters per second (1,270,000 cfm) ventilates the 8100-level production zone; one split of 100 cubic meters per second (210,000 cfm) ventilates the development of the 7700- level production zone; and one split of 165 cubic meters per second (350,000 cfm) ventilates the 7500 rail haulage level. The haulage tunnel requires an additional 188 cubic meters per second (400,000 cfm) of air. Development-drift ventilation is accomplished by hanging 1.0 m (3.5-foot) diameter steel ducting in the drifts with 40-horsepower, 0.96 m (38-inch) diameter fans supplying 9.4 cubic meters per second (20.000 cfm). The normal maximum length for these systems is 300 m (1,000 feet). The 8100-level production-area ventilation system is especially suited to a high level of mucking activity confined in a small area. Approximately 93 per cent of the mine's total production is transferred from the drawpoints to ore passes in 10 production drifts. The active area in each drift is 300 m (1,000 feet). Twelve 5-cubic-yard LHD units with Cat turbo- charged 170-horsepower engines are assigned to the area. Under these conditions, more than one LHD is assigned to a particular production drift. Adequate ventilation is maintained by making an air change every 97 m (320 feet) along the production drifts. Fresh air is brought into the production drifts from the fresh-air level through 1.37 m (4.5-foot) diameter raises. Air travels south along the production drift to the ore pass where it is exhausted down the ore pass to the exhaust level. The ore pass is followed by another intake which is followed by an ore-pass exhaust. At the south end of the production area, a series of exhaust fans maintain a southerly air- flow through the production level.

Jan 1, 1981

By A. Steiner, K. L. Komarek

Activities of aluminum in solid Ni-A1 alloys have been determined between 20 and 60 at. pet Al and 1200" and 1400°K by an isopiestic method in which nickel specimens, heated in a temperature gradient, are equilibrated with aluminum vabor in a closed all-alumina system. The activity of aluminum shows a strong negative deviation from Raoult's law at low concentrations but increases by three orders of magnitude within the ß(NiAl) phase. The partial molar enthalpy and entropy of mixing are negative. Using Wagner and Schottky's theory of ordered compounds, a degree of disorder of 4 x 10 -4 for NiAl and 1.25 X 10-2 for FeAl has been calculated THE Ni-A1 system has been studied by a great number of investigators, and the results, as far as the phase diagram is concerned, have been compiled by Hansen.1 The phase boundaries from 0 to 50 at. pet Ni are well-established. At higher nickel contents the boundaries are still in dispute and an additional phase, A12Ni3, has been reported.' The phase diagram is dominated by a very stable high-melting compound, NiA1, with a relatively wide range of homogeneity. Heats of formation of solid alloys have been determined calorimetrically by Oelsen and Middel3 from 20 to 95 at. pet Ni and by Kubaschewski4 from 25 to 80 at. pet Ni. According to the most recent compilation5 no other thermodynamic investigations have been reported for the Ni-A1 system. Due to the corrosive nature and the low vapor pressure of aluminum, a method has been employed for determining activities of aluminum which was previously developed for the Fe-A1 system.= Nickel specimens, heated in a closed evacuated alumina system in a temperature gradient, were equilibrated with aluminum vapor from a source within the system kept at constant temperature. After complete equilibration the specimens were analyzed and activities calculated from the known vapor pressure of aluminum. APPARATUS AND EXPERIMENTAL PROCEDURE Materials. The nickel specimens were made from wafers of electrolytic nickel (International Nickel Corp.) of 99.99 pet purity which were rolled to a 0.001-in.-thick foil by Driver-Harris Co. and to a 0.005-in.-thick sheet in our laboratory. The aluminum (Aluminum Corp. of America) had a purity of 99.99+ pct. The alumina tubes and crucibles were made of impervious recrystallized alumina with an alumina content of 99.7 pet (Triangle RR, Mor-ganite Inc.). Experimental Procedure. Annular specimens were punched from the sheet, the punching burrs removed, and the specimens degreased in carbon tetrachloride and acetone and weighed on a micro-balance to within an accuracy of ±0.01 mg. The specimens were positioned with alumina spacers along an alumina tube, and the positions measured. Aluminum metal was machined into cylindrical shape, and placed into an alumina crucible. The tube with the specimens was then inserted into a hole drilled into the aluminum metal. An alumina tube with its closed end at the top was slipped over the specimens so that its lower end fitted snugly into the alumina crucible. The assembled reaction tube was inserted into a mullite tube with a water-cooled brass head which had an opening for a quartz thermocouple protection tube and a metal-to-glass connection to a conventional vacuum system. A Pt-Pt 10 pet Rh thermocouple could be raised and lowered in the quartz tube which was placed along the outside of the alumina reaction tube. The mullite tube was heated by two separately controlled resistance-tube furnaces so that in the experimental temperature range an over-all temperature gradient of approximately 150o to 250°C could be imposed on the reaction tube. The position of the mullite tube was adjusted so that the surface of the aluminum metal was always at the temperature minimum. The reaction tube was thoroughly evacuated before and during slowly heating the assembly up to the melting point of aluminum. A pressure of less than 2 µ (Hg) was maintained during an experiment. Once the aluminum had melted, it isolated the contents of the alumina tube from the surroundings. Several times during an experiment the temperature gradient was carefully measured. An experiment lasted from 3 to 6 weeks and it was terminated by air cooling the evacuated mullite tube. For further details of the experimental procedure the paper on the Fe-A1 system6 should be consulted.

Jan 1, 1964

By J. L. Smith, A. L. Albee

This article presents a series of guidelines by which the geologist can evaluate the likelihood of surface faulting and its probable extent at any given site in Southern California and Nevada. The information is intended primarily for geologists concerned with establishing design criteria for proposed nuclear plants. The geologic problems involved in the location of a nuclear power plant are fundamentally no different from those for other types of installations. They fall into four main categories: foundation stability, landslides and slope stability, shaking due to earthquakes, and surface faulting. For problems in the first three categories the foundation engineer, the geologist, and the seismologist can provide criteria for plant location and design, and these problems can generally be economically handled by appropriate design measures for a project of the magnitude of a nuclear plant. However, problems in the last category — surface faulting — are more difficult to handle and require a unique evaluation. Accordingly, this paper will deal primarily with the problem of establishing design criteria for surface faulting, particularly as it affects nuclear facilities. A nuclear reactor is a power source that for greater safety is contained in a heavy, air-tight structure, just as gas, oil, water, and other power sources must be contained. Surface faulting is significant in that it may reduce the integrity of the containment by affecting critical exterior piping or by breaching of the containment. A similar significance exists relative to dams or tanks for the storage of water, gas, or oil, except that in these latter examples the breaching of the container automatically releases the fluids to do their damage. This is not necessarily the case with the rupture of a reactor containment structure because the function of the containment is totally protective, i.e., it is necessary only in the event that radioactive products are released from the reactor, and there are many other safeguards to pre- vent this release even if the containment is ruptured. At the present time, nuclear power plants must be located near large sources of water for cooling the steam generated. The construction of an industrial facility of any kind on the coast line is esthetically distasteful to most people since, unfortunately, there is not enough coast to fulfill all the needs and all the desires of all the people. In most cases where industrial facilities encroach on the lives of citizens, there is no mechanism other than zoning laws by which a person can effectively protest. But in the case of a nuclear facility, the public hearing required by the Atomic Energy Commission provides a forum for dissent, as in recent case histories, and the question of safety provides objectors with a weapon for fighting the construction of the plant. The nature of a public hearing for a nuclear plant is such that the prospective owner and operator must prove that there is no undue hazard, whereas the objectors need only demonstrate that there is a reasonable doubt. It is in this situation that geology becomes the Achilles Heel of nuclear power plant location. For his investigation, the geologist has natural exposures of rock at the ground surface and a limited number of trenches and drill holes to give him a fairly complete picture of the distribution of the various rock types. From the surficial data, he must infer three more dimensions — depth below the surface, past time, and future time. Unlike many problems faced by engineers, the geologist has only this one set of data from which to reach a conclusion — he is unable to reproduce the natural sequence of events in order to obtain another set of data for comparison. Hence, by the very deductive nature of a geologic conclusion, it is difficult to prove a geologic conclusion beyond a reasonable doubt even to other geologists — and perhaps one should say especially to other geologists because the experience and background of a geologist will strongly influence his conclusion, and no two geologists have exactly the same experience and training. The engineer and the public official would like the geologist to conclude that faulting cannot occur at a given site or to assign a numerical value to the probability of its occurrence — but no responsible geologist can do either of these things. Since government officials and others must make decisions that affect the public safety, it would seem that the geologic profession must attempt to establish criteria and

Jan 1, 1968

By David Turnbull

IN isothermal recrystallization processes, new crystals generally grow into the matrix until they impinge upon other new crystals or an external surface, at constant linear rates G. Before impingement the perceptible course of growth can be described by the equation: 1 = G(t-7) C1I where, G = dl/dt, 1 is a crystal dimension measured in a constant direction, t is the time, and 7, the nucleation period, is a positive intercept on the time axis. Fig. 1 is a schematic representation of I as a function of time for a recrystallizing grain. G is dependent upon temperature, driving energy (strain or surface energy), relative grain and boundary orientations, but is generally independent of time. The frequency of nucleation, fi, (time" volume") can be defined by the equation: N = 1/fV [2] where ? is the mean nucleation period and V is the volume of the specimen that has not recrystallized. The kinetics of primary and secondary recrystallization generally can be described satisfactorily in terms of the parameters N and G only.'-" After recrystallization is complete the average grain size 7 increases with time by "normal grain growth;" didt, the average rate of grain growth, is strongly time dependent and has not yet been precisely related to G for the motion of the individual grain boundaries constituting the system. It has been suggested4* " that the elementary act in grain boundary migration is closely related to the elementary act in grain boundary self-diffusion. Although the distance of atom movement in the two processes may be somewhat different, there is reason to expect that the activated states may be very similar, so that the free energy of activation for grain boundary migration should be of the same order of magnitude as for grain boundary self-diffusion. Therefore, it is desirable to develop a satisfactory basis for comparing data on self-diffusion and grain boundary migration and to make such comparisons where possible. Theory The formal theory of grain boundary migration rates is analogous to the theory for the rate of growth of crystals into supercooled liquids reviewed elsewhere 6-8. Boreliuss has shown that the latter theory describes, within the theoretical uncertainty, the growth of selenium crystals into supercooled liquid selenium. Motto and more recently Smolu-chowski" have derived expressions for the rate of boundary migration in recrystallization. The treatment to be presented is similar to Mott's excepting that the formalism of the absolute reaction rate theory will be used. The atomic mobility, M, in grain boundary migration is defined by: G = -M6p/6x where p is the chemical potential per atom and x is the coordinate measured in the direction of grain boundary movement. Let AF be the free energy difference per gram atom on the two sides of the boundary and k the thickness of the boundary. For RT>>AF the potential gradient across the boundary (6p/6x) is essentially linear and it follows that: SF/8x = - aF/N\ [4] where N is Avogadro's number. According to the Nernst-Einstein equation, M is related to a diffusion coefficient, Do, for matter transport in grain boundary migration by the equation: M = Da/kT [5] Substituting eqs 4 and 5 into eq 3 gives the basic relation between Do and G: G = DoaF/\RT [6] Do values may be calculated from experimental values of G from eq 6 and directly compared with the coefficient of self-diffusion within the crystal, DL, or the grain boundary self-diffusion coefficient D,. However, a more convenient, though equivalent, basis for comparing atomic mobility in grain boundary migration and self-diffusion is through the constants of the absolute reaction rate theory. According to this theory diffusion coefficients may be written:" D = k2(kT/h) exp [-AF,/RT] 171 aFa, the free energy of activation, is related to the measured energy of activation, Q, by the equation: AFA = Q - T aSx - RT [8] where aSa is the entropy of activation. Substituting eqs 8 and 7 into eq 6 gives: G = ek(kT/h) (aF/RT) exp [(AS,,)C/R] exp C-Qc/RTI C91 where the subscript G refers to boundary migration. The relationship between the driving free energy and the free energy of activation in boundary migration is indicated schematically in Fig. 2. Experience indicates that the variation of G with temperature can be described by: G= Go exp [- Qc/RT] [10] where Go and Qc are generally temperature independent over wide ranges of temperature. Comparison of eq 9 with eq 10 gives:

Jan 1, 1952

By D. B. Robinson, C. A. Macrygeorgos, G. W. Govier

Experimental data have been obtained on the volurrletric behavior of ternary mixtures of methane, hydrogen sulfide and carbon dioxide at temperalures of 40°, 100" and 160°F up to pressures of 3,000 psia. The results indicate that the compressibility factors for this system do not agree with compressibility factors for sweet natural gases at the same pseudo-reduced conditions. The deviation increases as the temperature and methane content decrease. Discrepancies of up to 35 per cent were observed. A careful analysis has been made of the existing pUrblished data on compressibility factors for binary systems containing light hydrocnrbons and hydrogen sulfide or carbon dioxide. It has been found that the deviation of actual from predicted compressibility factors for methane-acid gas mixtures is a function of the methane content and the pseudo-critical properties,.v of the mixture. The ratio between actual compressibility factors for methane-acid gas mixtures and compressibility factors for sweet natrlral gases at the same pseudo-reduced conditions has been currelated over a range of pP,, from 0 to at least 7 arid a range of pT, from about 1.15 to at 1east 2 0 with an error not exceeding 3 per cent and over most of the range within I per cent. The validity of the correlation for mixtures containing appreciable hearvier hydrocorbons has not been fully established, but it is shown to be preferable than the use of a corretation based only on hydrocarbons. INTRODUCTION Although a relatively accurate method for predicting compressibility factors of pure materials is provided by charts based on reduced properties and the assumption that the compressibility factor is a unique function of T P and z the determination of the correct values of compressibility factors for gas mixtures is somewhat difficult. Two general methods of dealing with gaseous mixtures have been proposed. The first assumes a direct or modified additivity of certain properties of the mixture in terms of the properties of the individual components. Examples of this method are based on the familiar laws of Dalton and Amagat. The second method averages the constants of an equation of state applicable to the pure components. Both of these methods are of limited value in engineering calculations because the first usually provides reliable answers only over narrow ranges of pressure and temperature and the second is cumbersome to handle. In petroleum engineering practice accurate estimations of the volumetric behavior of natural gases arc frequently required. To fulfill this need, several generalized compressibility charts have been developed.' ' Of these, the one prepared by Standing, el al is widely used at present. In the construction of charts of this type a third method for dealing with mixtures has been followed. It is based on correlation of pseudo-critical properties as outlined by Kay and calculated from the critical properties of the individual components in a mixture. Although these charts provide relatively accurate information on the compressibility of dry or wet sweet natural gases, they are less reliable when used for gases containing high concentrations of hydrogen sulfide or carbon dioxide or both. Thus, an experimental program, although time consuming, is the best means now available for the determination of the volumetric behavior of sour or acid gas mixtures. An increased interest in the behavior of these gas mixtures, particularly in connection with some of the fields in Western Canada where the acid gas concentration of the reservoirs may be as high as 55 per cent and where hydrogen sulfide alone may be as high as 36 per cent, provided the incentive for this study. It was the purpose of the investigation to determine the volumetric behavior of selected mixtures of methane, hydrogen sulfide and carbon dioxide over a range of temperature from 40" to 160°F and at pressures up to 3,000 psi. EXPERIMENTAL METHOD The apparatus used in this investigation was basically the same as that described by Lorenzo.'" The amount of each pure component used in preparing the gas mixtures was measured over mercury in a glass-windowed pressure vessel. The pure components were then transferred individually in the desired amounts to a second glass-windowed pressure vessel where the volumetric behavior of the mixture was determined. Volume was varied by mercury injection or withdrawal. The capacity of the cell was about 125 cc. Temperatures in the cells were measured with copper-constantan thermocouples and a Leeds Northrup semi-

By B. E. Eakin, R. T. Ellington

An apparatus and a procedure for determining the viscosity behavior of hydrocarbons at pressures up to 10,000 psia and temperatures between 77 and 400° F are described. The equipment is suitable for measuring viscosity of either the liquid or vapor phases or the fluid above the two-phase envelope for systems exhihiting retrograde phenomena, according no the phase state of the system within these ranges of temperature and pressure. Equations are developed for calculation of viscosity from the experimental measurements, and new data for the viscosities of ethane and propane at 77° F are reported. INTRODUCTION With the advent of higher pressures and temperatures in industrial processes and deep petroleum and natural gas reservoirs, demand has increased for accurate values of physical properties of hydrocarbons under these conditions. Proportionately, more frequent occurrence of natural gas and condensate-type fluids is encountered as fluid hydrocarbons are discovered at greater depths. This increases the importance, to the reservoir engineer, of being able to predict accurately the physical properties of light hydrocarbon systems in the dense-gas and light-liquid phase states. Reliable gas viscosity data are limited primarily to measurements made on pure components near ambient temperature and at low pressures. Few investigations have been reported for high pressures, and except for methane, data on light hydrocarbons are subject to question. This is demonstrated by the large discrepancy between sets of data on the same component reported by different investigators. For mixtures in the dense gas and light liquid regions and for fluids exhibiting retrograde behavior there are very few published experimental data. Viscosity data for methane have been reported by Bicher and Katz,1 Sage and Lacey,12 Comings, et al,3 Golubev,3 and Carr,3 with good agreement among the last three sets of data. Comings, Golubev and Carr utilized capillary tube instruments for which the theory of fluid flow is well established. The theory permits calculation of the viscosity directly from the experi- mental data and dimensions of the instrument alone. Sage and Lacey, and Bicher and Katz used rolling-ball viscometers. The theory of the rolling-ball viscometer has not been completely established, and these instruments presently require calibration by use of fluids of known viscosity behavior before viscosities of test fluids can be measured. To obtain accurate data it is necessary that the rolling-ball viscometers be calibrated by use of fluids of density and viscosity similar to the test fluids, a difficult selection for the gas phase. From the methane data and experimental tests on various natural gases, Carr developed a correlation for predicting the PVT behavior of light natural gases.2,3,4 This correlation was based on data for a very limited composition range; its application to rich gases and condensate fluids is questionable. The object of this investigation is to develop an instrument which can be used to obtain viscosity data at reservoir temperatures and pressures, for rich gases, condensate-type systems above the two-phase envelope and light liquid mixtures. These data will be used in an effort to develop correlations to represent the viscosity behavior of these fluids. APPARATUS In a previous viscosity study Carr2 utilized a modified Rankine capillary viscometer configuration," Fig. 1. In this instrument the gas to be tested is forced through the capillary tube in laminar flow by motion of a mercury pellet in the fall tube, the measured displacement time being that required for the mercury slug to move between the brass timer rings. The viscometer is constructed of glass and mounted in a steel pressure vessel. The test gas pressure in the viscometer is balanced by an inert gas (usually nitrogen) in the vessel. Excellent results have been obtained with instruments of this type, with Carr2 and Comings5 reporting repro-ducibilities of 99.5 to 99.3 per cent and an estimated absolute accuracy of 99 per cent. However, these instruments have limitations which have precluded their use for liquids. The need for maintaining a balance between pressures of the test fluid and inert gas in the viscometer vessel presents operating problems, and requires charging the test fluid to the viscometer very slowly. The principle drawback to the Rankine unit is behavior of the mercury slug which provides the pressure differential across the capillary. When even trace quantities of propane or heavier hydrocarbons are present in the test gas, the mercury tends to subdivide

By Neils Hansen

The microstructure of dispersion-strengthened aluminum aluminum-oxide products containing from 0.2 to 4.7 wt pct of aluminum oxide has been examined by optical and transmission electron microscopy, and the flow stress has been determined at room temperature and at 400C by tensile testing. Products were examined as recrystallized and as high-temperature extruded, and the microstructures consisted of a fine dispersion of oxide particles in a matrix divided by respectively recrystallized grain boundaries and subgrain boundaries. The flow stress (0.2 pct offset) at room temperature of recrystallized dispersion strengthened aluminum aluminum-oxide products is the superposition of dispersion strengthening and grain boundary strengthening. This superposition has been found to be linear. The flow stress (a) can be related to the grain size (t) by the Petch equation: ing content of oxide and k is a constant independent of the oxide content. For extruded products a similar relation has been found by replacing the grain size by the subgrain size. The k-value is of the same order for the two types of structure, which shows that the subgrain boundaries are as effective slip barriers as grain boundaries. Tensile testing at 400C of re-crystallized and extruded products shows that oxide dispersion strengthening is very effective, whereas the strengthening effect of grain boundaries and subgrain boundaries is small. THE microstructure of dispersion-strengthened products consists of hard particles finely distributed in a metal matrix. The strengthening effect of the dispersed phase has been fairly well established,1 and it has been found that the size and volume fractions of the dispersed particles are important structural parameters. However, in many dispersion-strengthened products which have been worked and heat-treated during manufacture the matrix is divided into well-defined grains or sub-grains, which may also have a strengthening effect. A model of the matrix strengthening in dispersed products worked during manufacture has been proposed,2 introducing the energy of the structure as a strengthening factor, especially at low temperatures. A difficulty in this model is, however, to relate this (stored) energy to the structural parameters directly observable as for instance grain size. The strengthening effect of the matrix grain size after recrystallization has been in- vestigated for nickel-thoria (TD-Nickel) products3 and for copper aluminum-oxide products. Conclusive results were, however, not obtained as the grain size of TD-nickel was constant. 5 to II , after recrystallization at temperatures from 700 to 1200°C and as the copper products containing 5 to 1 wt pct of aluminum oxide could not be recrystallized even after severe cold reduction and heat treatment at 1050C. For aluminum aluminum-oxide products containing from 1 to 5 wt pct of aluminum oxide it has been shown that the tensile strength at room temperature decreases when an extruded product is cold-worked and recrystallized. The matrix in the extruded products is divided into well-defined subgrains of micron size, and as the grain size of the recrystallized products is about two orders of magnitude higher, it is obvious that grain boundary strengthening occurs. Preliminary results8 have indicated that the flow stress containing no grain boundaries, A is a constant and t is the subgrain size. At elevated temperatures the effect of boundaries is more complex; it has been shown11 that recrystallized products having an oxide content of about 3 wt pct are more creep resistant than extruded material in the temperature range 400° to 600°C, whereas on application of a higher strain rate the tensile flow stress (0.2 pct offset) is higher in extruded than in recrystallized aluminum—5 wt pct aluminum oxide products at temperatures from room temperature to 427°C (800), Finally it has been shown12 that the Brinell hardness at 350°C of extruded products having about the same content of aluminum oxide increases with decreasing grain size, determined by X-ray line-width measurements. The present study was undertaken to obtain a quantitative relationship between the tensile strength and the grain size of aluminum aluminum-oxide products in the recrystallized as well as in the extruded state. The tensile testing was performed at room temperature and at 400uC. The grain size of the recrystallized products was varied by changing the degree of cold-work preceding the recrystallization heat treatment. In extruded products grain (or subgrain) size variations were obtained by high-temperature heat treatment after extrusion. EXPERIMENTAL a) Materials. Aluminum aluminum-oxide products have been manufactured by consolidation of aluminum powder covered with a layer of aluminum oxide formed during powder manufacturing. The products examined were manufactured from atomized powder containing

Jan 1, 1970

By J. A. Retty

IN the Labrador iron fields two concessions, totaling nearly 24,000 square miles, have been staked out and commercial-grade deposits delineated. The Newfoundland-Labrador concession, owned by the Labrador Mining and Exploration Co. Ltd., is a 20,000-square-mile tract in the upper basins of the Hamilton and N askaupi Rivers which drain into Lake Melville. The New Quebec licensed area is 3900 square miles, owned by the Hollinger North Shore Exploration Co. Ltd., lying to the northwest of the northwestern part of the Labrador concession. It includes the upper basin of the Swampy Bay River and part of the upper basin of the Whale River, both of which drain into Ungava Bay. Both of the above-named companies are controlled by Hollinger Consolidated Gold Mines Ltd. with The M. A. Hanna Co., of Cleveland, holding a minority interest. When exploration was first undertaken in 1936, the only published map of the area was that prepared by A. P. Low in 1895. It showed only the main watercourses and gave only a rough, general idea of the geology. The numerous lakes of this vast area had to be first sketched and then mapped. Since then, extensive geological and topographical surveys have been conducted by the Labrador company, work which is normally done by Government branches. The object of the work was to examine the area and gradually eliminate unfavorable or less favorable prospecting ground. With this object in view, geological

Jan 1, 1948

By AIME AIME

THE STANDARD herewith submitted is the result of several years of research and consideration by the A.I.M.E. Technical Committee on Milling Methods. In the early work of this committee it was found necessary to undertake the development of a standard laboratory method for screen testing of ores. During the research stages the desirability of having this standard, when completed, approved as American Standard was brought out. In accordance with this idea, its initiation as a project of the American Standards Association (then the American Engineering Standards Committee) was approved by the latter body and the A.I.M.E. designated as sponsor. In 1929, the A.S.A., on recommendations of its advisory committee, the Mining Standardization Correlating Committee), authorized the A.I.M.E. to be sole sponsor for this project. The personnel of the Institute's Committee on Milling Methods was then increased to make it thoroughly representative of all diversified interests in the mining field. Two years ago the standard was circulated and has been given wide distribution. Early in 1932 the committee voted unanimously, with 38 affirmative votes, that the standard be recommended to the Board of Directors of the Institute for submission to the American Standards Association for approval as American Recommended Practice. This was accordingly done, at the Feb. 1.6, 1932, meeting of the directors, and the American Standards Association approved the standard on July 6; 1.932, designating it as ASA M5-1932.

Jan 1, 1932

By AIME AIME

THE ninth International Petroleum Exposition held at Tulsa, May 16-23, broke all size, sales, and attendance records of previous shows. More than $12,500,000 worth of equipment was on the grounds. There were 546 companies exhibiting and every available inch of the fifteen acres allotted to exhibit was taken. Drake Drive, the main street of the exposition, was literally "supply row" with National Supply, Frick-Reid, Continental Supply, Oil Well, Bridgeport, International Derrick and Equipment, and Parkersburg Rig and Reel companies occupying the entire space. The exhibitors were a cross section of American industry, with such firms, besides the strictly oil equipment firms, as the United States Steel Corp. and others allied to the oil industry, exhibiting. Between $10,000,000 and $15,000,000 of equipment is estimated to have been sold on the grounds during the exposition. Valuable contacts were made by the exhibitors with key oil men. Attendance passed the 175,000 mark for paid admissions in contrast with 154,000 for the eighth exposition in 1934. Visitors registered from Venezuela, Soviet Russia, India, Germany, Spain, Mexico, England, Canada, France, Colombia, Greece, West Indies, and Rumania. Hotels were overflowed and a housing bureau found rooms in private homes for thousands. Oil companies set up a schedule of shifts in order that as many of their field men might attend as possible. It is said that the companies want a two-weeks' show in 1938 so that more time will be avail-

Jan 1, 1936

By D. C. DERINGER

METALLURGISTS and mill operators appreciate, in a general way, .the economic or commercial relationship between recovery and grade of product but few have correlated in detail fluctuating metal prices with the metallurgy. They know that many factors such as metal price, dedusiions for returning charge, transportation, percentage of metal in head ore, etc.; all affect the commercial relationship between recovery and grade of product. In practically every mill some one at some ' time has calculated the amount of recovery that can be sacrificed for each percentage increase in grade of concentrate and from this calculated ratio the commercial or ., economic tail has been established. Such a ratio finally becomes a well-entrenched rule by which the progress of the metallurgy is judged.. When once established, these-, ratios are but seldom corrected to changes of metal prices for each possible grade of concentrate that may be produced. The calculation is tedious when often repeated. Other methods have been suggested and used to correlate the commercial with the metallurgical phase. A factor .derived ,by multiplying the grade of concentrate by recovery is often used, but is of little importance because it does not possess a single commercial quantity. The percentage monetary recovery calculated by dividing the gross value of the ore into the net smelter return gives a good economic index and, is to be commended, but it is difficult to correlate exactly and quickly the work of each day on a commercial basis.

Jan 1, 1931

By Cornelius F. Kelley

EVERY man connected with the mining industry should take a significant pride in the fact that he belongs to an industry and to a profession that, from the beginning, has been constructive. The miner digs his ore and he gives the metal to art, to industry, and to commerce. The nature of our business is destructive only in that we deal with a wasting asset. That should be a source of great pride to those who belong to the profession. But unfortunately, the product of our mines, our smelters, and our re- fineries does not always go to constructive purposes. There are times when, in the administration of the affairs of men, our product chiefly goes to purposes which are destructive. When we look upon the panorama of horror that is being enacted throughout the world today, we wonder whether any effort toward the development of civilization and culture and education and well-being has been worthwhile. We are appalled to see the things that have been developed, through the application of science, toward progress and efficiency, now used for the catastrophic destruction of those things which are the most valuable that man has built. We must find hope that this is but an episodic thing; that it must, in the infinite wisdom of the Almighty, usher in a period of peace and progress, of civilization and development that will make man's existence upon earth worthwhile.

Jan 1, 1941