Search Documents

By Benjamin N. Webber

THE peninsula of Nicoya contains virtually all of the known manganese deposits of Costa Rica. These are south and west of the Tempisque River, which flows across the peninsula near its juncture with the mainland. This peninsula forms the westernmost part of the province of Guana¬caste, which is the northern of the two Pacific Coast provinces of Costa Rica. The larger villages are connected by ox-cart roads and trails. The area may be covered on horseback without difficulty except during the rainy season, when rivers are in flood and difficult to ford. This is particularly true of the Rio Seco-Guayjiniquil area, where there are no inhabitants and few open trails through the tropical jungle. Santa Cruz and Sardinal are served by the Taca Airlines, two planes a week from San Jose and Puntarenas. The port of Puntarenas has excellent loading facilities but none are available nearer the manganese districts; there ore must be lightered to vessels standing offshore. PHYSIOGRAPHY In Costa Rica there are three physiographic divisions: (I) the central plateau (Mesa Central), a somewhat dissected lava platform upon which are superimposed volcanic peaks, some of which are still active; (2) the Atlantic lowlands and (3) the Pacific lowlands. The peninsula of Nicoya and the larger part of the province of Guanacaste lie within the Pacific low lands. The term "lowland" indicates relation to the central plateau, as the peninsula of Nicoya is largely mountainous. The mountains of Nicoya form the southern extremity of a range of low hills, which are almost continuous along the Costa Rican coast to the Nicaraguan border. The coast line shows evidence of subsidence. The Gulf of Nicoya obviously is the drowned valley of the Tempisque River. The west coast of Nicoya shows many rocks, shoals, bays, inlets and small islands as evidence of a sea encroachment. The altitude of the manganese deposits ranges from 0 to 800 ft. Topography is of the mature type of wide valleys and low ,hills, often with abrupt slopes. The climate is tropical and humid; rainfall of 125 in. falls largely between Sept. I and Jan. I. Vegetation often is very dense, the Rio Seco-Guayjiniquil area being truly tropical jungle, containing many hardwoods. HISTORY AND PRODUCTION The production of manganese ore in Costa Rica apparently dates from the first World War. It reached a peak of about 10,000 tons in the year 1919, then declined rapidly. Evidence of this period of prospecting has rotted away or been swallowed by the jungle. The war now in progress apparently revived the interest in Costa Rican manganese and has encouraged further prospecting. Deposits long known have been redenounced and trails have been cut through the jungle to them. Many new deposits have been discovered in the last

Jan 1, 1942

By George Smith

IN discussing present-day business and industrial troubles we easily drop into the habit of clinical diagnosis. Talk of this kind, with its emphasis on suspicious symptoms and abnormal tendencies, makes us all morbid. As an English essayist has put it, we may thus induce a melancholy, temper that simply in-vites the ministrations of social and political quacks. It is far better-because nearer the truth-for us to recognize that our condition is in no sense diseased, that our body politic, social and economic, is suffering merely from growing pains; that America is not de-cadent-indeed, that any lapses from staid normality are traceable to the, excesses of youth. Our chief .trouble, then, is only that our industrial state is still young; it may be that we have been growing too fast. The growth in the industrial development of our country from pioneer days to the present time has been marvelous. Too many of us, however, take all this as a matter of course-we credit this record of American progress to our American genius alone. Too often we overlook the fundamental relationship between resources and progress-that man is aided and even guided by Nature. The fact is, social advance, indus-trial progress, national prosperity all have their ma-terial basis in natural resources. In furnishing the needed mineral raw materials to the great manufac-turing industries of the United States there has been no halt, but rather a general acceleration. No other phase of American activity can show-equal advance. As the decades have passed, the winning of mineral wealth has progressed from the role of a stimulus for western exploration to that of the foundation for nation-wide business. In 1890 the Sherman law was passed; since then the population of the United States has about doubled. Since then, too, thevalue of the annual product of the mines of this country has increased better than eight-fold-from 650 millions to 51/ billions of dollars. Since then the four largest branches of the mineral industry, which supply the iron and copper, the bituminous coal and petroleum-the bone and sinew and the energy of all other American industries-have increased their annual output nearly ten-fold as to value and six-fold as to quantity. Such a growth in the volume of mineral output must be taken as a true measure of the ex-ceptional service rendered by the mines of the United States. Not only is this a much larger country than it was 38 years ago, but its growing mineral industry has met demands that have been out of all proportion to the growth of the population.

Jan 8, 1928

By J. F. Myers, F. M. Lewis

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By A. G. H. Andersen, A. W. Kingsbury

SILICON bronzes containing iron are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 determined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at 1100°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. Of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West7 have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,12, 7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. PREPARATION OF SAMPLES Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 3 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1942

By Benjamin N. Webber

THE peninsula of Nicoya contains virtually all of the known manganese deposits of Costa Rica. These are south and west of the Tempisque River, which flows across the peninsula near its juncture with the mainland. This peninsula forms the westernmost part of the province of Guanacaste, which is the northern of the two Pacific Coast provinces of Costa Rica. The larger villages are connected by ox-cart roads and trails. The area may be covered on horseback without difficulty except during the rainy season, when rivers are in flood and difficult to ford. This is particularly true of the Rio Seco-Guayjiniquil area, where there are no inhabitants and few open trails through the tropical jungle. Santa Cruz and Sardinal are served by the Taca Airlines, two planes a week from San Jose and Puntarenas. The port of Puntarenas has excellent loading facilities but none are available nearer the manganese districts; there ore must be lightered to vessels standing offshore. PHYSIOGRAPHY In Costa Rica there are three physiographic divisions: (I) the central plateau (Mesa Central), a somewhat dissected lava platform upon which are superimposed volcanic peaks, some of which are still active: (2) the Atlantic low-lands and (3) the Pacific lowlands. The peninsula of Nicoya and the larger part of the province of Guanacaste lie within the Pacific low lands. The term "lowland" indicates relation to the central plateau, as the peninsula of Nicoya is largely mountainous. The mountains of Nicoya form the southern extremity of a range of low hills, which are almost continuous along the Costa Rican coast to the Nicaraguan border. The coast line shows evidence of subsidence. The Gulf of Nicoya obviously is the drowned valley of the Tempisque River. The west coast of Nicoya shows many rocks, shoals, bays, inlets and small islands as evidence of a sea encroachment. The altitude of the manganese deposits ranges from o to 800 ft. Topography is of the mature type of wide valleys and low hills, often with abrupt slopes. The climate is tropical and humid; rainfall of 125 in. falls largely between Sept. I and Jan. I. Vegetation often is very dense, the Rio Seco-Guayjiniquil area being truly tropical jungle, containing many hardwoods. HISTORY AND PRODUCTION The production of manganese ore in Costa Rica apparently dates from the first World War. It reached a peak of about 10,000 tons in the year 1919, then declined rapidly. Evidence of this period of prospecting has rotted away or been swallowed by the jungle. The war now in progress apparently revived the interest in Costa Rican manganese and has encouraged further prospecting. Deposits long known have been redenounced and trails have been cut through the jungle to them. Many new deposits have been discovered in the last

Jan 1, 1942

By E. H. Kelton, R. D. Grissinger

In designing structural members of steel and some other materials the design engineer has available recognized values of elastic modulus and safe working stress that may be substituted in well-known engineering formulas to give him desired cross-sectional areas and deflections for a particular part. Zinc, on the other hand, has no generally recognized modulus. It flows under continuously applied loads. Therefore, the designer of structural members must use a range of working stresses depending on the continuous load and the amount of permissible distortion. The only method of obtaining these values is by creep testing. Creep testing of zinc has been carried on for some 20 years by this laboratory, covering a wide range of zinc and zinc alloys. Types of test included tension, compression, and simple and cantilever beams at temperatures ranging from o to I50°C. Specimen conditions ranged from as-cast or as-rolled to accelerated aged in steam or dry air. Effects of plating were investigated also. It is not the intention of this paper to expound all these factors but rather to present the final data on well-known zinc die-casting alloys and to suggest means of applying these data to engineering design. Early Work In the early work on creep testing of zinc, the direct-loading tension method was used. However, direct loading of die castings was unsatisfactory because of the high loads required. For instance, a standard die-cast tension bar having a cross-sectional area of about 0.049 sq. in. would require a direct load of about 1000 lb. for a unit stress of 20,000 lb. per sq. in. Also, tests were made at nominal room temperature, but normal variations caused fluctuations greater than those due to experimental error or other causes, so that control of this variable within ±1/2°C. seemed essential. These two factors led to the development of an apparatus described by J. Ruzicka,' in which the specimens were loaded by means of a lever and were held at constant temperature by means of an oil bath. While Ruzicka's apparatus yielded excellent check results, it seemed desirable to have some setup by which literally hundreds of die-cast specimens could be tested at the same time. This would permit the conducting of a number of low-load tests designed to run 10 years or longer and still leave capacity for current high-load work. Beam testing in a constant-temperature room was the answer. Test Method Preliminary work indicated that die-cast beams of various lengths and cross scctions yielded the same result within reasonable limits regardless of whether they were tested as simple beams, uniformly loaded beams, or cantilevers. Accordingly, the simplest type was adopted. This was a,

Jan 1, 1945

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By Donald W. Scott

Generally speaking, there is nothing very difficult about taking good microgrztphs of photogenic thin sections or grains with a petrographic microscope-camera setup. However, sometimes it is desired to show some detail that cannot be illustrated satisfactorily by the usual micrographs taken with parallel polarized light, with crossed nicols, or even with two micrographs. A simple procedure giving good results has been used at Battelle Memorial Institute for subjects falling into this classification, and it is believed to be of interest, especially to research people who must sell a point to executives through the medium of well-illustrated reports. The following problem illustrates a typical application: It is desired to photograph a thin section of an iron ore to illustrate the character and association of the iron oxides and the individual quartz crystals. A magnification of 75 dia. is acceptable. A micrograph of the field in question (Fig. Ia) was taken with parallel polarized light. Due precaution was taken to provide critical illumination, correct exposure, a sharp focus, a good darkroom technique, and other essential conditions. It illustrates correctly the iron oxides, but it fails to show the individual quartz crystals. A micrograph of the identical field (Fig. Ib) was taken under the same precise conditions, but with crossed nicols. It gives a better idea of the character of the individual quartz crystals but is likely to be misinterpreted unless accompanied by a lengthy descriptive note. This micrograph suggests that the centrally located, large black area is composed entirely of iron oxides. That this' is an incorrect interpretation is evident by reexamining the micrograph of Fig. Ia. The correct interpretation is that the dark area contains quartz crystals oriented with their optical directions parallel to, or nearly parallel to, the vibration directions of the polarizer and analyzer of the microscope. Thus, the executive, or anyone who had not done the work personally, would get no more than a fair interpretation, even if two micrographs were included; and in the interests of both brevity and clarity, one micrograph usually is more desirable. Exactly how many quartz crystals occur in this region cannot be told from the two micrographs, and a printing of the two negatives in register would likewise not show the detail desired. Thus, it is evident that some subjects cannot be satisfactorily illustrated by the usual procedures. In photographing Fig. Ic the light was subdued and, during the entire exposure of 75 sec., the analyzer nicol was rotated uniformly in its mounting from a crossed position to 45° uncrossed position to introduce the desired amount of contrast in the various individual quartz crystals. The true reproduction of the character and association of the iron oxides, and the additional structure and detail in the quartz areas, is apparent. It might be

Jan 1, 1949

By Richard H. Willey

Efficient handling of large tonnages in open-pit mining demands, primarily, an abundance of well fragmented rock. To accomplish this, a drilling and blasting department composed of a well-knit, versatile group of workers and supervisors must be established. Some costs will remain relatively on the same level over a period of years, while others can be greatly lowered as will be shown. 'The Utah Copper Division, Kennecott Copper Corp., Bingham Canyon, Utah, has been ever alert for improvements in operating methods and equipment to gain increased efficiency and lower costs. Bingham Canyon MIne The greatest dimension of the mine is 8000 ft northeast-southwest with a width of 5000 ft southeast-northwest. From the lowest level, at an elevation of 6040 ft above sea-level, the mountain rises in 27 benches on the west side to W level (elevation 7800 ft) and 21 benches on the east side to Q level (elevation 7460 ft). At the inception of open-pit mining in 1906, the overcapping of leached porphyry had to be removed to reach a commercial grade of sulphide ore. The overcapping or waste now remaining is quartzite with intercalated limestone beds. The limestones are usually soft in nature except in the south-middle portion of the mine where they have been meta-morphized along the contact zone. This area usually gives drilling and blasting operations a great deal of trouble. Here occurs the greatest amount of secondary blasting, as the well-established fracture planes cause the altered beds to break into large boulders. Several massive quartzite "ribs" occur in the overburden, and as a result, the uniform breakage is difficult to obtain. The major quartzite areas have been subjected to complex folding, fracturing and faulting because of the intrusion of the underlying stock. The monzonite porphyry, which carries the commercial values, presents no serious drilling problem because of its softness and extensive minute fracturing throughout the mass. A series of major slips or faults pass through the ore body which, although of considerable advantage to the drilling and blasting department, sometimes works to the disadvantage of the track department. Drilling an11 blasting of the porphyry apparently becomes easier as depth is attained. but highly siliceous streaks throughout the pit still present difficulties. At no place is the rock of such character as to allow excavation without preparations. On certain higher elevations or levels, old fill material can be dug by the shovels, but only at some risk to equipment because of bank slippage. Past Methods At the outset of shovel operations in 1906, drilling was done with the Ingersoll-Rand F-24 piston drill mounted on an un-

Jan 1, 1949

By H. E. Hostetter

Grossmann's method1 for calculating the hardenability of steel from the composition and grain size has gained wide acceptance, and when properly used, has been well proved in practical application, both for estimating the hardenability of known compositions and for selecting compositions to meet known hardenability requirements. The Grossmann method uses as the criterion of hardenadility the "ideal critical diameter," DI, which is the' size round that will just harden to a structure of 50 per cent martensite at the center when given the theoretically fastest quench, or "ideal quench." The DI can be related to actual quenching practice if the severity of quench is known; or the DI can be correlated with hardenability as determined by the Jominy end-quench method.2 The effect on hardenability of each element present in a steel can be represented by a multiplying factor, the value of which depends on the amount of the element present and the degree of effectiveness of the particular element. (The value of the factor for a given carbon content varies with the grain size.) When the factors for all elements present in a steel have been determined from charts, they are multiplied, and the resultant product is the DI of the steel. The validity of Grossmann's scheme of multiplying factors has been confirmed in a number of other investigations.3-6 It can be appreciated that a certain desired level of hardenability can be obtained by adding chromium, molybdenum, nickel and vanadium to a base composition containing carbon, manganese, silicon and the usual impurities. Many of the ranges of hardenability used commercially can be obtained by any of the foregoing alloying elements used singly in the base composition. The same hardenability levels also can be obtained through use of any of a great number of multiple element combinations of these alloying elements. In this report a method will be presented for determining what one combination is the most efficient (based on hardenability and cost of added alloy) for a given level of hardenability. It should not be assumed from the emphasis given to hardenability, that hardenability is the only criterion for the selection of an alloy composition. Such properties as the hot-working characteristics, machinability, carburizing characteristics, amount of distortion during quenching and the retention of austenite may be considerations of importance in many applications. However, hardenability is one of the most important properties of an alloy steel and one that must be considered in almost all cases involving heat-treatment by quenching. Therefore, a method for determining the lowest-cost alloy combination should be of considerable value. Determination of Most Efficient Combinations For comparing the alloying elements on standards of cost and hardenability, it

Jan 1, 1947

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By W. C. Krumbein

GEOLOGICAL problems are approached from a geometrical (space relations) viewpoint, a kinematical (time sequence) viewpoint, or a dynamical viewpoint. The first two require sound training in conventional geology and in field methods. The third approach requires a solid foundation of chemistry, physics, and mathematics. Modern training for geologists should include close integration of basic sciences with geological principles. INTRODUCTION Our knowledge of the earth has increased tremendously during the last half century. We know more about its surface configuration, the distribution of its natural resources, the procession of living forms that inhabited it in the past, the chemical composition of its oceans, the areal distribution of its surface rocks, the movements of its atmosphere, and so on. Not only do we know more facts about the earth, but we have a better understanding of the processes that take place on and within it, such as the nature of earthquakes, the thermodynamics of the atmosphere, the chemical equilibria involved in the formation of igneous rocks, the mechanics of stream flow, the dynamics of the earth's origin, and so on. Many sciences contributed to the sum total of this knowledge, including such established disciplines as geology, geography, physics, chemistry, astronomy, biology. Out of this accumulation of new knowledge grew also a group of new sciences, such as seismology, oceanography, meteorology, volcanology, hydrology. Collectively these latter are known as the geophysical and geochemical sciences, and to a large extent they began as branches of geology. Until the turn of the century, for example, the study of earthquakes (seismology) was a part of geology, although as early as 1846 Mallet, a physicist, had suggested that the subject could be investigated by elastic-wave theory. Comparatively little progress was made along these lines until the seismograph was developed near the turn of the century; since then, additional earthquake data have accumulated rapidly, but more important, the interpretation of these data essentially has kept pace with their accumulation. In similar fashion, meteorology was generally considered a branch of geology as recently as one or two decades ago. Considerable progress had been made in such aspects as weather forecasting, but the science dates its recent rapid rise from the year 1911, when Bjerknes first applied the principles of dynamics to the analysis of air masses. The rapid development of such disciplines as oceanography, volcanology and hydrology was due in part to the application of principles of chemical equilibrium, of dynamics, and of thermodynamics to earth problems, by men who were essentially physicists or chemists by training. The last half century, therefore, and particularly the last two decades, saw the influx of numerous chemists and physicists into the realm of the earth sciences. In the meantime the main body of geology itself showed a marked growth, and

Jan 1, 1941

By R. E. Ogilvie, N. L. Peterson

DURING the past few years there has been considerable effort devoted to the understanding of radiation effects on materials. The concept of the Frenkel defect and other lattice defects suggests that radiation may alter the rate of many metallurgical phenomena, especially those which are diffusion controlled. In 1953 R. R. Coltman and T. H. ~lewitt' found an appreciable effect on the ordering rate of Cu,Au due to fast neutron bombardment. Since then several rather comprehensive theories have been proposed on radiation enhanced diffusion in solids.2"4 If the energy of the radiation is above the threshold energy for the removal of atoms from their lattice sites, Frenkel defects will be produced. These defects can be produced uniformly throughout a relatively thick specimen by high-energy X-rays permitting bulk property studies without the limitation of sample dimensions. In this work high-purity arsenic containing 30 ppm of impurities was allowed to diffuse from the gase- ous phase at 700°C into single crystals of p-type germanium containing 0.1 ppm of indium. As the arsenic diffuses into the P-type germanium, an n-type layer will form in the diffusion zone. At the p-n junction the concentration ratio of the arsenic to the indium is constant. Experimental Procedures—The germanium specimens, 10 mm by 10 mm by 5 mm, were polished and etched to a mirror finish. The specimens were then sealed off in a vycor glass capsule at 3 x 10"5 mm Hg pressure with a sufficient amount of arsenic powder to produce a one-half atm pressure of arsenic at 700°C. Specimens were annealed at 700°C without radiation. The diffusion coefficient determined from these samples agrees within 8 pct of previous work done by Fuller.' Three specimens were given diffusion anneals at 700°C in a small tube furnace centered beneath the target of a 2-mev Van de Graaff generator. The specimens when in the furnace were 10 cm directly below the target of the generator. These specimens were irradiated continuously during the diffusion run with the Van de Graaff operating at 2 mev with a tube current of 225 to 250 pamp. The intensity of the x-radiation at the surface of the specimen inside the furnace was approximately 4.5 x l05 roentgens per hr. The temperature was controlled within m2°C by a chromel-alumel thermocouple throughout this work with no observed temperature change due to the radiation. By careful lapping, the samples were polished at an angle of 5 deg to the diffusion zone, giving a XI0 increase in the visible diffusion zone. The location

Jan 1, 1960

By H. E. Hostetter

Grossmann's method1 for calculating the hardenability of steel from the composition and grain size has gained wide acceptance, and when properly used, has been well proved in practical application, both for estimating the hardenability of known compositions and for selecting compositions to meet known hardenability requirements. The Grossmann method uses as the criterion of hardenadility the "ideal critical diameter," DI, which is the' size round that will just harden to a structure of 50 per cent martensite at the center when given the theoretically fastest quench, or "ideal quench." The DI can be related to actual quenching practice if the severity of quench is known; or the DI can be correlated with hardenability as determined by the Jominy end-quench method.2 The effect on hardenability of each element present in a steel can be represented by a multiplying factor, the value of which depends on the amount of the element present and the degree of effectiveness of the particular element. (The value of the factor for a given carbon content varies with the grain size.) When the factors for all elements present in a steel have been determined from charts, they are multiplied, and the resultant product is the DI of the steel. The validity of Grossmann's scheme of multiplying factors has been confirmed in a number of other investigations.3-6 It can be appreciated that a certain desired level of hardenability can be obtained by adding chromium, molybdenum, nickel and vanadium to a base composition containing carbon, manganese, silicon and the usual impurities. Many of the ranges of hardenability used commercially can be obtained by any of the foregoing alloying elements used singly in the base composition. The same hardenability levels also can be obtained through use of any of a great number of multiple element combinations of these alloying elements. In this report a method will be presented for determining what one combination is the most efficient (based on hardenability and cost of added alloy) for a given level of hardenability. It should not be assumed from the emphasis given to hardenability, that hardenability is the only criterion for the selection of an alloy composition. Such properties as the hot-working characteristics, machinability, carburizing characteristics, amount of distortion during quenching and the retention of austenite may be considerations of importance in many applications. However, hardenability is one of the most important properties of an alloy steel and one that must be considered in almost all cases involving heat-treatment by quenching. Therefore, a method for determining the lowest-cost alloy combination should be of considerable value. Determination of Most Efficient Combinations For comparing the alloying elements on standards of cost and hardenability, it

Jan 1, 1947

By Arthur F. Taggart

ENGINEERING education today is like a crazy quilt of somber wools and gaudy shoddy, chain-stitched on an academic assembly line, and sold at ever mounting prices to inexperienced youths for lifetime use. Each engineering school offers a half-dozen or so patterns with essentially the same skimpy wool content. Sales appeal is in the color of the shoddy, denoted by the hopeful adjectives chemical, civil and the like. This article is argument for an all wool product made by slow, careful handwork. Bluntly it proposes a thorough four-year undergraduate drill in fundamental science and general engineering empirics, leavened by continuing study of the third of the engineer's troubles: Man. It is not contended that existing methods of engineering education have failed to start men on the path to successful engineering practice (too many of you have started that way); rather, social conditions and the bounds of knowledge have changed tremendously, and corresponding alterations in the pattern of engineering education are overdue. We'll Teach the Specifics The first part of this contention is illustrated by excerpts from a letter received recently from an officer of one of the largest corporations: "We are interested in employing two or three outstanding young engineers to be placed on a special training program to develop them as design and construction engineers.... "We propose to put these men on a four-month indoctrination and orientation course after which they would be given job-training assignments for a period that will vary from about six months to about a year and a half depending upon the aptitudes, abilities and intelligence of the candidates.... "I am not too fussy about what kind of engineers the men might be insofar as academic courses are concerned. They could be.. . in almost any engineering classification.... We can furnish the additional training beyond the academic fundamentals. "The starting rate for these jobs would be $326 per month...." This letter is not unique; rather it is representative of a practice that has become common. It is industry's enforced response to the general refusal by young graduates to submit to union domination in order to gain operating experience at the labor level. The message to engineering schoolteachers is plain: You teach the fundamentals; we'll teach our practice and pay the graduate to learn it. The letter means to the student that time spent in school studying the specific practices of particular industries is waste compounded. The school can't give the equivalent of what industry teaches, wherefore industry will still demand apprenticeship. The student must pay for the specific instruction at school instead of being paid to take it later. And time-consuming specifics crowd out drill in basic scientific and technical subjects as well as liberal arts.

Jan 1, 1952

By Donald W. Scott

Generally speaking, there is nothing very difficult about taking good microgrztphs of photogenic thin sections or grains with a petrographic microscope-camera setup. However, sometimes it is desired to show some detail that cannot be illustrated satisfactorily by the usual micrographs taken with parallel polarized light, with crossed nicols, or even with two micrographs. A simple procedure giving good results has been used at Battelle Memorial Institute for subjects falling into this classification, and it is believed to be of interest, especially to research people who must sell a point to executives through the medium of well-illustrated reports. The following problem illustrates a typical application: It is desired to photograph a thin section of an iron ore to illustrate the character and association of the iron oxides and the individual quartz crystals. A magnification of 75 dia. is acceptable. A micrograph of the field in question (Fig. Ia) was taken with parallel polarized light. Due precaution was taken to provide critical illumination, correct exposure, a sharp focus, a good darkroom technique, and other essential conditions. It illustrates correctly the iron oxides, but it fails to show the individual quartz crystals. A micrograph of the identical field (Fig. Ib) was taken under the same precise conditions, but with crossed nicols. It gives a better idea of the character of the individual quartz crystals but is likely to be misinterpreted unless accompanied by a lengthy descriptive note. This micrograph suggests that the centrally located, large black area is composed entirely of iron oxides. That this' is an incorrect interpretation is evident by reexamining the micrograph of Fig. Ia. The correct interpretation is that the dark area contains quartz crystals oriented with their optical directions parallel to, or nearly parallel to, the vibration directions of the polarizer and analyzer of the microscope. Thus, the executive, or anyone who had not done the work personally, would get no more than a fair interpretation, even if two micrographs were included; and in the interests of both brevity and clarity, one micrograph usually is more desirable. Exactly how many quartz crystals occur in this region cannot be told from the two micrographs, and a printing of the two negatives in register would likewise not show the detail desired. Thus, it is evident that some subjects cannot be satisfactorily illustrated by the usual procedures. In photographing Fig. Ic the light was subdued and, during the entire exposure of 75 sec., the analyzer nicol was rotated uniformly in its mounting from a crossed position to 45° uncrossed position to introduce the desired amount of contrast in the various individual quartz crystals. The true reproduction of the character and association of the iron oxides, and the additional structure and detail in the quartz areas, is apparent. It might be

Jan 1, 1949

By G. W. Josephson

SINCE the earliest years of recorded history the durability and protective qualities of asphalt and tar have been known and utilized. The mummies of early Egyptian kings were coated with asphaltic materials, and asphalt mastics were common in Babylon. However, according to various authorities, it was not until 1780 that the first forerunner of present-day composition roofing was discovered,1 and the large-scale expansion of the industry has taken place since 1900. HISTORICAL BACKGROUND Development was stimulated by the growing popularity of manufactured gas. The by-product tars from these operations accumulated in large waste piles that had no commercial value and were a source of annoyance and expense to the gas companies. These tars were offered at very attractive terms to anyone who would take them away, and the infant "composition" roofing industry benefited accordingly. At first the process consisted simply of dipping sheets of burlap or other fabric in a tank of molten tar or asphalt. The long strip of roofing was rolled up for convenient handling, and the early experimenters soon found that it was necessary to dust the surface of their new "roll roofing" with some kind of material that would prevent the tarred surfaces from sticking together. Any finely divided, low priced local material like sand or fine gravel served this purpose and from its application the roofing-granule industry grew. As time went on other characteristics of a properly applied mineral surfacing were recognized. As with wooden shingles, tar and asphalt can be ignited by flying embers from near-by fires. It was found that by increasing the largest particle size to the maximum that could be successfully embedded, and by properly controlling the amount of smaller fractions retained in the grade so as to cover the asphalt completely a Nigh degree of resistance to fire was attained. Needless to say, in this early period asphaltic roofing needed such selling points to gain acceptance in a field dominated by wood, slate, and tile. When asphalt is protected from the sun's rays it is extremely durable, but when exposed to sunlight its surface is comparatively rapidly decomposed. Completely covering asphalt roofing with mineral surfacing protects the asphalt and adds materially to the life of the roof-conservatively, 500 per cent. Slate Granules In the production of split slate shingles a large quantity of waste slate is accumulated, as 60 to go per cent of the rock quarried is discarded. This waste was a continuing burden on the industry. Some was marketed as ground slate flour for filler in paint and linoleum, and there is a record that as early as 1906 two carloads of coarse screenings from slate flour were marketed as granules for surfacing roofing. This new field appeared to the slate pro-

Jan 1, 1944

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds ;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2 : I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resins may serve as a habitat of microorganisms. In the decomposition of a medium. some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17, 32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By W. C. Krumbein

GEOLOGICAL problems are approached from a geometrical (space relations) viewpoint, a kinematical (time sequence) viewpoint, or a dynamical viewpoint. The first two require sound training in conventional geology and in field methods. The third approach requires a solid foundation of chemistry, physics, and mathematics. Modern training for geologists should include close integration of basic sciences with geological principles. INTRODUCTION Our knowledge of the earth has increased tremendously during the last half century. We know more about its surface configuration, the distribution of its natural resources, the procession of living forms that inhabited it in the past, the chemical composition of its oceans, the areal distribution of its surface rocks, the movements of its atmosphere, and so on. Not only do we know more facts about the earth, but we have a better understanding of the processes that take place on and within it, such as the nature of earthquakes, the thermodynamics of the atmosphere, the chemical equilibria involved in the formation of igneous rocks, the mechanics of stream flow, the dynamics of the earth's origin, and so on. Many sciences contributed to the sum total of this knowledge, including such established disciplines as geology, geography, physics, chemistry, astronomy, biology. Out of this accumulation of new knowledge grew also a group of new sciences, such as seismology, oceanography, meteorology, volcanology, hydrology. Collectively these latter are known as the geophysical and geochemical sciences, and to a large extent they began as branches of geology. Until the turn of the century, for example, the study of earthquakes (seismology) was a part of geology, although as early as 1846 Mallet, a physicist, had suggested that the subject could be investigated by elastic-wave theory. Comparatively little progress was made along these lines until the seismograph was developed near the turn of the century; since then, additional earthquake data have accumulated rapidly, but more important, the interpretation of these data essentially has kept pace with their accumulation. In similar fashion, meteorology was generally considered a branch of geology as recently as one or two decades ago. Considerable progress had been made in such aspects as weather forecasting, but the science dates its recent rapid rise from the year 1911, when Bjerknes first applied the principles of dynamics to the analysis of air masses. The rapid development of such disciplines as oceanography, volcanology and hydrology was due in part to the application of principles of chemical equilibrium, of dynamics, and of thermodynamics to earth problems, by men who were essentially physicists or chemists by training. The last half century, therefore, and particularly the last two decades, saw the influx of numerous chemists and physicists into the realm of the earth sciences. In the meantime the main body of geology itself showed a marked growth, and

Jan 1, 1941

By A. S. Nowick, E. S. Machlin

ONE of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.1 During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time required for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error.2~3 This method of showing stress-rupture data has been adopted by many investigators and the KACA.4 By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, 100, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time for rupture on stress, temperature, com- position, and structure. In order to obtain this information, an investigation was made at the KACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given com- position and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efficiency and power output of gas turbines used in aircraft propulsion can be increased. THEORY The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 eveloped by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate- process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process.'' For example, in a chemical reaction the unit process is

Jan 1, 1947