Search Documents

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metal-lurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial invest-ment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding.

Jan 1, 1939

By W.G. Harbert, C. Upthegrove

DURing the past year considerable work dealing with physical properties of cartridge brass was done at the University of Michigan in cooperation with the Ordnance Department of the U. S. Army. This paper gives some of the data bearing on the effect of the anneal, previous to the final reduction-or rolling, on the physical properties, particularly the hardness. Various phases of the subject of physical properties of cartridge brass have been presented by different investigators. Mathewson and Phillips1 refer to the work of Grard, in 1909, as the first systematic presentation of the relation between temperature and time of anneal, changing of physical properties and microstructure, and the previous reduction by cold rolling. They discuss the relation between time and temperature of annealand the previous reduction by cold rolling; also the relation between physical properties and grain size of annealed brass. The degree of deformation previous to the annealing was found to determine the temperature at which recrystallization and corresponding changes in physical Properties would take place. relation between grain size and Brinell hardness, found the hardness for low-temperature annealing to be dependent on the previous degree of reduction, while for anneals above a certain temperature the hardness after the anneal was independent of the degree of reduction. Actual differences in hardness, due to the degree of reduction, disappear only on annealing at 600" C. or above; though the differences for metal subjected to different degrees of reduction and annealed at temperatures between 350" and 600" C. were found to be relatively small. In their determination of the relationship of grain size to Brinell hardness, Bassett

Jan 1, 1923

By J. Donovan Jacobs

An underground excavation project usually is a highly organized complex of different but interrelated construction activities. It is the whole effort, including the necessary tools, which will be referred to as the System. Tunnel-driving and shaft-sinking operations are among the most systematic of construction efforts. Systems are not new in the performance of construction. It is the Systems Concept which seems only recently to have been discovered and made the subject of much study and discussion. HISTORICAL From the seventeenth century, when explosives were first utilized for rock excavation, until the successful application of the rotary-head continuous tunneler in this decade, the cyclical drill-blast-muck-support method has been standard tunnel-driving procedure throughout the world. Whatever improvements occurred were the result of development of better tools for performing the various operations of the cycle. The electric locomotive replaced the mule and permitted the use of larger muck cars. The steam drill, which ended the day of the double jack, was itself quickly made obsolete when compressed air replaced steam as the source of drilling energy. Power shovels were introduced to save the time and money involved in the hand-loading of excavated materials. A cubic yard of rock tunnel muck can be excavated today for just half the man-hours of labor required in 1948. Developments over 20 years which cumulatively have resulted in this economy include: drifter drills mounted on hydraulically controlled booms and positioners; tungsten-car- bide-tipped bits; long feed shells on the drifters, making it possible to drill the full depth of a round without changing steel; better designed,

Jan 1, 1970

By W. G. Harbert, C. Upthegrove

DURing the past year considerable work dealing with physical properties of cartridge brass was done at the University of Michigan in cooperation with the Ordnance Department of the U. S. Army. This paper gives some of the data bearing on the effect of the anneal, previous to the final reduction-or rolling, on the physical properties, particularly the hardness. Various phases of the subject of physical properties of cartridge brass have been presented by different investigators. Mathewson and Phillips1 refer to the work of Grard, in 1909, as the first systematic presentation of the relation between temperature and time of anneal, changing of physical properties and microstructure, and the previous reduction by cold rolling. They discuss the relation between time and temperature of annealand the previous reduction by cold rolling; also the relation between physical properties and grain size of annealed brass. The degree of deformation previous to the annealing was found to determine the temperature at which recrystallization and corresponding changes in physical Properties would take place. relation between grain size and Brinell hardness, found the hardness for low-temperature annealing to be dependent on the previous degree of reduction, while for anneals above a certain temperature the hardness after the anneal was independent of the degree of reduction. Actual differences in hardness, due to the degree of reduction, disappear only on annealing at 600" C. or above; though the differences for metal subjected to different degrees of reduction and annealed at temperatures between 350" and 600" C. were found to be relatively small. In their determination of the relationship of grain size to Brinell hardness, Bassett

Jan 1, 1923

By R. B. Moore

Page History................................ 708 What is Radioactivity?........................ 710 Disintegration Series.......................... 711 Radium Ore Deposits......................... 713 Metallurgical Treatment........................ 717 Methods of Ore Concentration..................... 722 Future Supply of Ore......................... 723 Uses of Radium............................ 723 Mesothorium as a Substitute for Radium................. 724 Discussion.............................. 725 Probably no other metal excites as much interest, among both scientific men and the general public, as radium. This is due partly to the high cost of radium salts and partly to the peculiar properties of the element. Since radium-bearing ores were discovered in the United States, the interest of American scientific men has been stimulated and, at the present time, more radium is extracted and refined in this country than in all the rest of the world together. HISTORY The property of radioactivity was discovered, partly by accident, by Henri Becquerel, the French physicist, in 1896. He was experimenting with certain fluorescent substances in order to find, if possible, a connection between fluorescence and the recently discovered X-rays. Among other chemicals which possess the property of fluorescence, he was using salts of uranium. His custom was to expose the fluorescent substance to the action of sunlight and then register the effect of possible penetrating radiation on a photographic plate protected from ordinary light. Bec-querel's experiments gave positive results at once, and he at first believed that he had discovered a relation between fluorescence and X-rays. Later he exposed a plate to a uranium salt which had not been previously exposed to sunlight. To his surprise, on developing this plate, he found that he had obtained the same effect as he had previously secured when

Jan 1, 1919

By Michael Tenenbaum, T. L. Joseph

In a previous investigation1 the authors studied the effect of pressure on the reduction of iron ores by hydrogen. With hydrogen as a reducing agent, the rate of reduction was increased substantially by increasing the pressure from 1 to 2 atmospheres. The results with hydrogen prompted the present study of the effect of pressure on reduction with carbon monoxide and with mixtures of carbon monoxide and nitrogen. Features of Reduction Process The gas stream in the lower part of the blast furnace always contains sufficient concentrations of reducing gases to complete reduction provided sufficient time is allowed for the reaction to proceed. Reducing gases react immediately with the iron oxide on the surface of lumps of ore. However, as the unreduced surface recedes from the easily accessible exterior of the lump, the reaction proceeds by virtue of the diffusion of the gases into and out of individual pieces. The rate of diffusion of gases, which undoubtedly plays an important role in the reduction of iron ores, depends on several factors, most important of which are: (1) molecular weight or density, (2) pressure, (3) temperature, (4) concentration gradient. Thus, the rate of reduction of a lump of iron ore at any temperature will depend not only on the specific reaction rate but also upon: (1) available surface of unreduced iron oxide, (2) rate of diffusion of the reducing gas to the reacting surface, (3) rate of effusion of the gaseous products of the reaction from the reacting surface, (4) adsorption of the gases on the reacting surface. The various features of the reduction process were discussed in previous work and need not be reviewed. However, in order to explain

Jan 1, 1940

By D. A. Belforti, M. P. Lepie

Spectroscopically pure copper was melted on sapphire plaques in a zydrogen atmosphere. The surface tension of the liquid metal was determined using the sessile drop technique. Measurements were made by direct observation with the aid of a specially const,mcted telescope. The value obtained, 1268 dynes per cm, is compared to that found in the literature. THERE is at this time considerable interest in the use of ceramics for vacuum tubes. The crystalline material is superior to the more conventional glass in mechanical strength, chemical inertness, dielectric properties, ability to withstand high temperatures, and so forth. However, ceramics are much more difficult to seal hermetically with metals than are the glasses. For this reason an investigation was undertaken to determine the wetting and adhesion of metals to ceramics. The sessile drop technique offers a convenient means at elevated temperatures for measuring liquid surface tension, wetting angle, density, spread- ing coefficient, and work of adhesion. Thus, from the contour of a drop of liquid at rest on a solid surface one can obtain a quantitative evaluation of the degree to which the two substances will bond. To this end a special apparatus was constructed so that various molten metals could be observed. Standardization of the apparatus was done initially by measuring the surface tension of copper since this is well documented in the metallurgy literature. Although there are many methods available for the measurement of surface energy,'+ the sessile drop technique has been used most extensively for molten metals and ceramics.5"' Fig. 1 illustrates the dimensions to be measured. From these values, the surface tension of the liquid can be obtained using the Bashforth and bdams' equation and tables.

Jan 1, 1963

A knowledge of the principles of punctuation is essential to effective and intelligible writing, for the ease and pleasure of the reader, and even his understanding, may depend upon the choice and the placing of punctuation marks. To 'punctuate' is to mark with stops or points; the word comes from the medieval Latin punctuare (punctuatus), which in turn is derived from the Latin punctum, a point. The purpose of punctuation is to show the manner in which the writing is to be understood; to indicate the relations between parts of a sentence and between successive sentences. To some extent "it does for the eye what vocal stress does for the ear", but especially it marks logical relations. Some punctuation marks, such as those indicating admiration, exclamation, and interrogation, are rhetorical as well as grammatical, but most of the common ones are logical or grammatical. My discussion will be confined to grammatical punctuation in ordinary writing. "The problem of punctuation in text matter", as George Summey * says, "is to employ words, points, and paragraph breaks in such a way as to achieve at the same time clearness, proper distribution of emphasis, and the desired kind of movement." The criticism of the punctuation of a sentence or of a group of sentences is not final until the context, within the paragraph, is read. A paragraph is a sentence or a group of' sentences forming an independent unit of the composition; it represents a unit of thought. A multiplicity of paragraphs produces a choppy effect; on the other hand, paragraphs of excessive length are tiresome, because the belaboring of one unit of thought wearies the reader. The aim should be to

Jan 1, 1931

By R. D. Leitch, W. P. Yant, R. R. Sayers

In 1924, the United States Public Health Service was requested to undertake a special study of stream pollution. The Public Health Service asked the United States Bureau of Mines to take up the study because the training and experience of the personnel of the former was considered not to be as well suited to this type of investigation as that of the Bureau of Mines. Under H. Foster Bain, then Director of the Bureau, field investigations were begun in the spring of 1925. Along with mine-drainage wastes, the problem of gas-house and coke-oven waste was investigated in the laboratory and a method of treatment by sodium hydrate and benzol was found to be promising. The idea was obtained by A. C. Fieldner, chief engineer of the Bureau Experiment Stations, on a trip to Germany in 1924. He saw a practical application of the process, but obtained no information as to definite chemical or mechanical processes. Because of the then pending American patent applications by the German firm, we made no attempt to develop our findings further. Shortly afterward, a similar method of treatment was developed in the United States,' and since that time we have devoted our attention entirely to mine drainage. This paper is a presentation of some general facts and information gathered during the past five years on coal-mine drainage. Scope of Work There was such a diversity of opinion at the time this work was begun, on the whole subject and apparently so little accurately known, that it was decided to undertake a basic study from which first, certain definite information might be evident, and second, what might be considered

Jan 1, 1931

By H. G. Warren, E. W. Hough

Correlation of interfacial tension of the methane-n-pentane and methane-n-decane systems was made by Hough and Stegemeier by the use of the Weinaug and Katz equation. The methane-n-heptane and ethylene-n-heptane systems were investigated by the authors. Additional systems taken from the literature were the me thane-propane system by Weinaug. and Katz, the methane-n-butane system by Pennington and Hough, and the n- butane -carbon dioxide system by Brauer and Hough. These systems were analyzed by the Weinaug-Katz equation and the Sugden equation on the IBM 1620 11 computer using a regression analysis program. Parachor and exponent values for each component and system were determined. The experimental work was close to the critical point of the light component in the n-butane-carbon dioxide and ethylene-n-heptane systems, between the critical points of the light and heavy components in the methane-n-pentane, methane-n-heptane and methane-n-decane systems, and close to the critical point of the heavy component in the methane-pmpane and methane-n-butane systems. An empirical formula was developed to find a value of the constant B in the Sugden equation for binary hydrocarbon systems from the parachor values of the two components. Interfacial tension for binary hydrocarbon systems was found to be a direct function of liquid-vapor phase density difference in the same manner as a single-component system. DISCUSSION Interfacial tension may be defined as the measure of the specific free surface energy between two phases having different compositions.1 The interfacial tension (IFT) for a binary system may be predicted for any temperature and pressure if the

Jan 1, 1967

By George Burrell

INTRODUCTION THE senior author of this paper, while in Colorado on other official business, made a trip to the Cripple Creek gold-mining district to get more data than are at present available regarding the composition of the gas that issues from the rock into the mines of the district. This was done at the suggestion of George S. Rice, Chief Mining Engineer of the Bureau of Mines. There are many questions of interest and importance in connection with the ventilation of the mines in the Cripple Creek district, such as the menace to life and mining of a suffocating gas entering the mines from the rock, the danger due to powder smoke (from blasting operations), and danger of continued inhalation of rock dust by the miners. This report confines itself to the first problem, the gas from the rock, and principally to one phase of this question, the composition of the gas and its effects on men and lights. A more thorough study of this and other ventilation problems is planned. That the, rock gas is a real menace is shown by the fact that miners (variously estimated from 25 to 50 by different persons interviewed) have been killed by it in the 25 years that mining has been vigorously carried on at Cripple Creek. Many men have had narrow escapes from death, some of them having been incapacitated for days. In addition, much loss of time results because at certain periods of the year or on certain days it is impossible to enter some workings. At a few mines fans force air into the workings, thus supplementing the natural ventila-

Jan 5, 1916

By Richard F. Miller, W. E. Milligan

Work was undertaken two years ago at the Hammond Laboratory for the purpose of determining the magnitude of the elastic range in single crystals of pure metals by means of creep tests, the assumption being made that if a true elastic range exists, the elastic limit represents the maximum stress for no creep. A sensitive extensometer was constructed, and creep tests were made on zinc single crystals at a variety of loads and temperatures1. It was soon discovered that there is no measurable elastic limit in ductile zinc single crystals at, or above, room temperature. The inference that pure metallic single crystals may not possess a definite elastic range was not justified, however, since zinc had been tested in creep only above its recrystallization temperature, and several investigator2,3,4 had already shown that above the recrystallization temperature polycrystalline metals will flow under very small stresses, while below that temperature stresses of a much larger magnitude are required. For that reason, it was decided to extend the study of the elastic limit to other metals having a higher recrystallization temperature than zinc. Aluminum and silver were selected, because of the ease of obtaining pure materials and of preparing large single crystals, and because the crystallo-graphic glide system of these metals is well known. Owing to the limited time available, the elastic range was investigated by slow tensile tests rather than by creep tests. Production of Specimens A luminum Recrystallized single crystals were prepared from 99.95 per cent aluminum supplied by the Aluminum Company of America. The ingots were melted in an Acheson graphite crucible in a gas furnace, and cast

Jan 1, 1937

By Michael Tenenbaum, T. L. Joseph

In a previous investigation1 the authors studied the effect of pressure on the reduction of iron ores by hydrogen. With hydrogen as a reducing agent, the rate of reduction was increased substantially by increasing the pressure from 1 to 2 atmospheres. The results with hydrogen prompted the present study of the effect of pressure on reduction with carbon monoxide and with mixtures of carbon monoxide and nitrogen. Features of Reduction Process The gas stream in the lower part of the blast furnace always contains sufficient concentrations of reducing gases to complete reduction provided sufficient time is allowed for the reaction to proceed. Reducing gases react immediately with the iron oxide on the surface of lumps of ore. However, as the unreduced surface recedes from the easily accessible exterior of the lump, the reaction proceeds by virtue of the diffusion of the gases into and out of individual pieces. The rate of diffusion of gases, which undoubtedly plays an important role in the reduction of iron ores, depends on several factors, most important of which are: (1) molecular weight or density, (2) pressure, (3) temperature, (4) concentration gradient. Thus, the rate of reduction of a lump of iron ore at any temperature will depend not only on the specific reaction rate but also upon: (1) available surface of unreduced iron oxide, (2) rate of diffusion of the reducing gas to the reacting surface, (3) rate of effusion of the gaseous products of the reaction from the reacting surface, (4) adsorption of the gases on the reacting surface. The various features of the reduction process were discussed in previous work and need not be reviewed. However, in order to explain

Jan 1, 1940

By Edmund M. Wise

NATURE has provided us with many metals, but with few really good ones, and frequently the better metals are the rarer. It is to this circumstance that many physical metallurgists, inventors, and just plain experimenters owe their employment, for much of their work is directed, consciously or otherwise, toward the alleviation of some of the more serious shortcomings of the cheaper, less noble, and weaker metals; by alloying, age-hardening, passivating, cladding, plating, and other useful dodges, which sometimes permit the substitution of one of the less gifted metals for one of the really good ones. As a matter of fact, the varied needs of our complex civilization could be quite well met with only five metals, if they were sufficiently abundant, and one of the five would certainly be platinum, the most noble and versatile that nature provides. Many metals are difficult to handle and seem to take pleasure in defying their investigators to find good uses for them, and finally when a use is found it is frequently quite a specific one; in other words, a hole has to be found--or perhaps made-to fit the peg. It is for this reason that a large amount of research must be con- ducted before the more recalcitrant metals become really useful. In platinum, however, we have a metal that inherently possesses so many valuable attributes that it became useful as soon as methods for producing it in massive ductile form were devised, and once its complicated chemical behavior was understood it became principally an aid to research rather than the subject thereof. In recent years, much research has been done to further improve

Jan 1, 1953

By John R. Freeman

THIS paper relates entirely to the casting of brass under fluid pressure in steel dies Die castings of metals and alloys of low melting point have been available for many years but the development of brass die castings has been relatively recent, occurring within the past five years The successful development of brass die castings has resulted from the availability of alloy steels that would give satisfactory life as dies and the development of suitable die-casting machines The melting point of copper is 1084° C (1983° F ) and of a high brass about 900° C (1652° F ), as compared to 327 5° C (6215 °F) for lead, 419 4° C (786 7° F) for zinc and 658 7° C (1217 7° F) for aluminum, temperatures that ale indicative of the casting temperatures required for the various types of alloys, of which the melting points are somewhat lower than those of the pure metals TYPE OF DIE-CASTING MACHINE In the well-known plunger and gooseneck types of die-casting machines used for casting the alloys of relatively lower melting point, much of the working mechanism is immersed in the molten alloy For alloys having the relatively high melting point of brass, this obviously is impossible Machines with a separate melting chamber are essential Two rather distinct types are in extensive use at the present time, the Pack and Polak machines, the former designed by Charles Pack and developed at the American Brass Co , the latter developed by Zoseph Polak, of Prague, Czechoslovakia The principles of operation of these machines have been described in articles by Pack1,2,3 and by Sieg 4

Jan 1, 1935

By Ernest A. Hersam

The small amalgamation-test of the laboratory is not always reliable as a basis for important decisions as to the character and commercial treatment of ores. The conditions of continuous practice on a large scale are not always reproduced in the brief laboratory-test. Sometimes such a reproduction would be very difficult, or impracticable; sometimes it is not even attempted, and the test is performed in a rough way, without regard to the effects of small variations in the methods pursued. The aim of a laboratory amalgamation-test is to learn how much of the gold or silver in an ore can be economically recovered by amalgamation on a commercial scale. The yield can be increased, perhaps, by additional chemical treatment or by extreme comminution of the ore; but this might cost more than the value of such increase. Moreover, in practice, other operations often follow amalgamation; and these operations may remedy a defective extraction by amalgamation, more economically than could be done by directly increasing that extraction. The test should be performed, therefore, upon a uniformly-sized material, and under conditions that are precisely known and capable of being exactly duplicated, or purposely modified. The crucial feature of the test is the effectiveness of the contact made between the gold or silver of the ore and the amal-gamating-surfme. This may depend upon the temperature; the duration of contact; its force, due to gravity or impact; the hardness, plasticity or liquidity of the amalgam; the roughness or other quality of the amalgam-surface; the scouring action of the ore upon the amalgam, or the suspension and

Jan 1, 1905

By Ronald W. Utley

INTRODUCTION The ''Do's and Don'ts" of installing equipment in a comminution circuit begin during the study stage of a proposed project, continue through preliminary engineering, detail engineering, procurement, the actual placement of equipment at the job site, and end with turnover to the owner. Equipment supplied for a modern comminution circuit will be high quality, rugged machinery designed according to appropriate manufacturing standards for long hours of trouble-free service. However, certain precautions and procedures must be observed in plant design and layout, equipment handling, installing and servicing in order to obtain optimum performance. This chapter contains general installation "DO'S and Don'ts" for the major equipment in the circuit. •Primary Gyratory Crushers •Rock Breakers (Hammer) •Belt Conveyors •Apron Feeders •Weigh Belt Scales •Secondary Crushers •Vibrating Screens •Grinding Mills •Mill Liners •Open Gear Sets •Speed Reducers •Electric Motors •Cyclones •Slurry Pumps Some questions will not be covered in this chapter, or may not be applicable to the actual equipment purchased, as requirements do vary from manufacturer to manufacturer. Additional specific information can be obtained by contacting the manufacturer's local representative or the factory. All inquiries should be accompanied by the following information: •Unit size and type of equipment •Manufacturer's shop order number (after order placement) •Serial number (after manufacture) DO'S 8 DON'TS FOR INSTALLATION OF ALL COMMINUTION CIRCUIT EQUIPMENT Installation By Design DO obtain tables of weights and clearances from manufacturer. DO obtain WR2 forces from manufacturer to determine that the foundation is adequate. DO determine compression strength of foundation soil and/or rock. DO obtain manufacturer's recommended typical foundation drawings. If substantial alteration to manufacturer's drawings is required, check with the manufacturer before proceeding.

Jan 1, 1982

By John L. Schroder

In selecting the best system of mining for a particular operation, many different factors must be considered. The system to be finally selected should be that which provides: 1) The highest possible degree of safety for mine personnel. 2) The lowest cost per ton of product. 3) The maximum coal production per man-shift. 4) The most suitable quality of final product, considering its intended use. 5) The maximum percent recovery of coal per acre of reserve consistent with cost and subsidence rights. 6) Consideration for the ecology of the area. Some of the important factors to be considered when choosing a method of mining are: 1) Amount of cover over the coal seam. 2) Type of the rock in the overburden. 3) Characteristics of the coal seam including: (a) the thickness of the coal seam; (b) the nature and location of any impurities or irregularities; (e) the dip (or pitch) of the coal seam; (d) the nature and direction of any definite cleavage ill the czoa1 seam; (e) the hardness of the coal; (f) the structural strength of the coal; and (g) the presence, anti amount, of explosive gas (methane). 4) Quantity of water likely to be encountered in the mining operation. 5) Nature and strength of the roof (top) over the coal seam. 6) Nature and strength of the floor (bottom) under the coal seam. 7) Any previous or concurrent mining in seams above or below the coal seam to be worked. Information on items 1-7 may be obtained in several ways. Topographical and geological reports and maps of the area are generally available

Jan 1, 1973

LANS are underway for the annual meeting of AIME, to be held in New York, February 17 to 21. The technical program includes meetings of all divisions of all three branches, Mining, Metals, and Petroleum. The bulk of the technical sessions will be held at the Statler Hotel, and the annual banquet will be held at the Waldorf-Astoria, Wednesday evening, February 20. The technical program of the Mining Branch activities is included in this issue. While it is not complete in every detail, it shows general interest groupings as well as subjects to be discussed. The program for each division is shown separately to facilitate following the activities of these special interest groups. Then, after a full scale and possibly somewhat strenuous technical meeting, a post-meeting feature will appeal to many of the members. A restful cruise to Bermuda and Nassau is offered at special rates to AIME members and friends. The schedule is a 3:00 pm departure from New York on the Queen of Bermuda on Saturday, February 23; arrival at Bermuda at 7:00 am Monday, February 25; arrival at Nassau at noon, Wednesday, February 27; and the trip ending again in New York at 9:00 am, Saturday, March 1. Rates begin at $202.10 per person, with higher rates depending upon accomodations desired. The base rate includes outside room with private bath and all meals, as well as Federal, Bermuda and Nassau taxes. Reservations for the trip should be made immediately through Leon V. Arnold, 36 Washington Square West, New York 11, who is in charge of arrangements.

Jan 1, 1952

By John R. Freeman

This paper relates entirely to the casting of brass under fluid pressure in steel dies. Die castings of metals and alloys of low melting point have been available for many years but the development of brass die castings has been relatively recent, occurring within the past five years. The successful developnlent of brass die castings has resulted from the availability of alloy steels that would give satisfactory life as dies and the development of suitablc die-casting machines. The melting point of copper is 1084" C. (1983" F.) and of a high brass about 900" C. (1652" F.), as compared to 327.5" C. (621.5" F.) for lead, 419.4' C. (786.7" F.) for zinc and 658.7" C. (1217.7" F.) for aluminum, temperatures that are indicative of the casting temperatures required for the various types of alloys, of which the melting points are somewhat lower than those of the pure metals. Type of Die-casting Machine In the well-known plunger and gooseneck types of die-casting machines used for casting the alloys of relatively lower melting point, much of the working mechanism is immersed in the molten alloy. For alloys having the relatively high melting point of brass, this obviously is impossible. Machines with a separate melting chamber are essential. Two rather distinct types are in extensive use at the present time, the Pack and Polak machines, the former designed by Charles Pack and developed at the American Brass Co., the latter developed by Joseph Polak, of Prague, Czeclioslovakia. The principles of operation of these machines have been described in articles by Pack1,2,3 and by Sieg.4

Jan 1, 1935