Search Documents

By G. C. Eggleston, W. E. Keck, W. C. Lowry

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant' mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939

By Donald O. Rausch, Adolph Soderberg

4.1-1. Introduction. Open pit mine planning must be correlated to all phases of a mining operation. The factors that must be considered in planning an open pit mine are numerous and must reflect the characteristics and surrounding conditions of a particular orebody. Therefore, only an outline of the subject can be presented here to aid the planning engineer in pointing out procedures that are generally applicable to pit design. The presentation is directed toward the planning of an open pit copper mine, but the procedures discussed should apply in most cases to any type of metallic or nonmetallic orebody. In planning an open pit mine the pertinent elements that must be included are: assays, geology, tonnage and areal extent of ore reserves, topography, mining equipment, economic factors of operating costs, capital expenditures, profit, types of ore, pit limits, cut-off grade, stripping ratio, rate of production, pit slopes, bench heights, road grades, ore metallurgical characteristics, hydrological conditions, property lines, and marketing considerations. 4.1-2. Sampling. Sampling must be adequate to classify the various materials to be removed from an open pit mine. Drillhole assays are plotted on sections and plan maps with ore and waste blocked out by selected bench intervals. These maps are prepared to depict the geological and other conditions existing on each mine level. The confidence factor to be applied to sampling and the resultant assays values must be given careful consideration. In uniformly disseminated de- posits, the confidence factor will approach unity. For widely fluctuating values, the average assay values should be discounted somewhat, the degree depending upon such factors as drillhole spacing. Such samples, at best, represent a very few pounds for hundreds to thousands of tons of ore

Jan 1, 1968

By W. M. Courtis

. There seems to be a well-established belief that there is an indescribable something in the appearance of gold-quartz not to be learned from books, that enables those who are fortunate enough to have acquired the power to recognize this characteristic, to pronounce at once that a certain quartz will or will not pay. The stronger this claim is made, the more certain is the claimant to be one of the self-styled practical miners. After several years spent among the gold-mines of California with practical and professional gold-miners, I have come to the conclusion that very few care to risk an opinion on a piece of quartz until some of it has been "horned out." Nevertheless, there is what the miners call a " kindly " appearance, that is more often followed by good results than is a vitreous, water-wet-looking quartz. A dark, resinous quartz seems to be most in favor, but there are so many exceptions that even quartz as " white as a hound's tooth " produces gold in some mines.. The ribbon-quartz, a laminated variety, separated by thin talc or chlorite partings, has a well-known good name. The slides of rich quartz specimens show that this parallelism is a microscopical characteristic of the only macroscopical distinction that, as a rule, these quartzes show. This is shown by Nos. 12 and 13, photographs of the richest quartz, that averaged $65 per pound. It is noticeable, also, in Nos. 7 and 9, and others. Dr. Hensoldt, of Columbia College, who prepared, excellently, a large number of my slides, and whom I have to thank for descriptions and suggestions, says of Nos. 12 and 13: "This variety of quartz differs considerably, microscopically, from the others of your locality, and is, in more than one respect, remarkable. Like the

Jan 1, 1890

By Adolph Knopf, L. G. Westgate

Pioche lies 240 miles southwest of Salt Lake City, in southeastern Nevada, 19 miles west of the Nevada-Utah line. It is at the end of a branch line (33 miles), which connects at Caliente with the Los Angeles and Salt Lake division of the Union Pacific System. Its commercial relations are with Salt Lake City and Los Angeles, chiefly with the former. The surrounding area is part of the Great Basin, an arid region of alternating mountain range and intermont plain, the latter floored with out-wash from the mountains. About Pioche the plain varies between 4700 and 6000 ft. above sea level. The town lies in a valley at the east base of a low northwest-southeast range (the Pioche Hills) 12 miles in length, which rises about 1000 ft. above the adjacent flat. West of the Pioche Hills is a higher north-south range consisting of two parts: to the south the Highland Range, between Bennett Pass and Stampede Gap; to the north the Bristol Range, from Stampede Gap to Bristol Pass. This double range reaches altitudes of 8000 to 9000 ft., or more (the highest point, Highland Peak, is 9395 ft.), and rises some 2500 ft. above the surrounding plain It is continued in lower hills to north and south. Smaller ranges rise from the flat west of the Highland and Bristol ranges. The area studied and shown on the map (Fig. 1) is covered by three inch-to-the-mile topographic sheets: the Highland Range, the Bristol Range, and the Panaca, the latter mapped in part only. The sedimentary rocks of the district include Paleozoic limestones, sandstones and shales, Pliocene tuffs, and modern wash. Igneous rocks are represented by intrusive dikes and stocks and by extensive lava flows of mid-Tertiary time.

Jan 1, 1927

By Joseph E. Pogue

In 1920, 531 million barrels of crude petroleum were coi~sumed in the United States. As imposing as this figure is, the fact that the domestic consumption of crude petroleum has increased at an average rate of 10 per cent. a year for the past decade is more striking. Will this rate of increase in demand continue? If so, the year 1930 will call for 1260 million barrels of petroleum—a staggering volume. On the other hand, may we expect the demand for petroleum to grow as rapidly as it did when the automotive industry was having its most phenomenal expansion? If not, to what extent will the growth of oil requirements decrease? When and to what degree will the petroleum industry become affected by the economic law of diminishing returns? Obviously, this matter requires careful analysis, especially as both national and industrial planning must be predicated upon present estimates of the requirements of the future. The purpose of this paper, accordingly, is to project, as closely as present limitations of knowledge permit, the course of the demand for petroleum in the United States over the next ten years. At first, the problem of estimating the future of a demand as complex as that for petroleum might appear insoluble. Fortunately, hon~ever, therc are several scientific methods of approaching the problem, centering around a study of rates of industrial growth, which lend considerable hope that the requirements of the immediate future in this field may be approximated with sufficient closeness to have practical value as a basis of action. Growth oF Petroleum Demand The demand for crude petroleum is the resultant of the demands for the products made jointly from this substance—gasoline, kerosene, gas and fuel oil, and lubricating oils. The demands for these have grown at

Jan 1, 1923

By José Geraldo Vieira

Companhia Vale do Rio Doce (CVRD), founded in 1942, is located near the town of Itabira, Brazil. Its iron ore deposits include over 500 million metric tons (mt) of high-grade hematite and about 2 billion mt of itabirite (banded rock formed by thin alternate layers of hematite and silica). These deposits are part of the Iron Ore Quadrangle, of which the overall reserves have been estimated at more than 30 billion mt. The magnitude of the project meant difficult early years for the company, including large investments, extensive railroad rehabilitation, and construction of ore port and ore handling facilities. Companhia Vale do Rio Doce was organized as a stock company, and 91% of its shares are presently owned by the Brazilian government. Financing has been accomplished in part through loans from international monetary agencies foreign banks, and foreign industry, as well as Brazilian banks. The company markets mainly abroad. In 1967, it exported 10.6 long tons (It) of ore, principally to West Germany, Japan, Netherlands, Italy, France, United Kingdom, and the United States. The Rio Doce geographic region where CVRD operates is strategically located among the large population centers of Rio de Janeiro, Belo Horizonte, Salvador, and Vitoria (Fig. 1). It covers an area of approximately 81,000 sq km in the states of Minas Gerais and Espirito Santo, and its population in 1968 was about 3.5 million. This region presents excellent prospects for development, with factors favorable for forestry, agriculture, grazing, and exploration for minerals other than iron ore, Electric power (hydroelectric plants) is available, as well as two main systems of transportation: the Rio-Bahia highway and the Vitoria-Minas Railroad. Pioneer activities at Itabira started about 1720 as small gold mining centers. The town is about 80 km northwest of Belo Horizonte and

Jan 1, 1969

By Chester Purington

PROBABLY no battleship of any great power save Japan could long remain in. the Pacific Ocean tinder present conditions, were it to depend for fuel supply on the hitherto developed coal or oil resources of any part of the adjoining lands in either hemisphere. This statement does not overlook the important but not inexhaustible oil fields of California, the bunker coals of British Columbia, nor the coals accessible and mined adjacent to Chinese water-ways. For both naval and merchant ships, however, modern practice seems to require high-grade Welsh or Pennsylvania bituminous even at great expense for transportation. Otherwise, we should not see British ships bunkering Welsh coal at Singapore nor the United States establishing a store of Pennsylvania coal at its naval base at Pearl Harbor, Hawaii. Compared with Atlantic coals, the best Miike and Nagasaki (Japanese) bunker coal, the Kailan coal of China, and the Welling-ton and Nanaimo coals of British Columbia, are dis-tinctly inferior, as one can soon learn from the chief engineers on Pacific liners. In addition to the coal used for steaming and bunker purposes, it is of increasing importance that an adequate supply of coking coal for metallurgical purposes should be made available at reasonable prices at industrial centers on the west coast of America, and at Japanese and Chinese coastal cities. The use of Chinese coking coals for smelting the iron of the lower Yang-Tse deposits is by no means so satisfactory as could be desired, while the poor quality. of Japanese coals for coking purposes is well known. If Russia, as seems not improbable, is to become a power on the Pacific in the course of the next few decades, she will doubtless develop an iron and steel industry in the Maritime Province, where an adequate and accessible supply of iron ore will necessitate a supply of coking coal.

Jan 9, 1923

By Henry M. Howe

The object of the present paper is to suggest injecting into the hearths of iron blast furnaces, whose temperature has become unduly lowered, some form of fuel whose calorific intensity, under the peculiar conditions existing there, is considerably higher than than of liquid petroleum, the rose of this substance for melting out chills having grievonsly disappointed the high hopes which were at first entertained of it. A chill being a fall of the temperature below that needed for the complete liquefaction of the slag, which requires, according to Plattner, about 1800' C., one would suppose that the chief thing to be accomplished in curing it would be to raise the temperature in the crucible of the furnace. The most obvious ways of doing this seem to be to raise the temperature of the blast, and to increase the amount of fuel in the crucible itself. Simply increasing the rate at which the blast enters the furnace, if carried beyond a certain point, should lower the temperature in the crucible. The existence of a chill shows that the fuel is arriving too slowly at the tuyeres. If air be introduced so rapidly as to he in excess of that required for the combustion of the fuel, all that excess will simply lower the temperature around the tuyeres, carrying the region of intense heat upwards, and weakening its intensity by increasing its size. Up to a certain point, increasing the rate of introducing the blast will increase practically pari passu the rate at which the fuel reaches the tuyeres. But when mechanical obstructions, which so often accompany chills, retard the descent of the fuel, there must be a point beyond which this does not hold good, and beyond which farther

Jan 1, 1883

COLUMBIA SECTION Holds four sessions during year. Annual meeting in September or October. S. S. FOWLER, Chairman, J. C. HAAS, Vice-Chairman, LYNDON K. ARMSTRONG, Secretary-Treasurer, 720 Peyton Bldg., Spokane, Wash. W. H. LINNEY, J. F. MCCARTHY. A special meeting of the officers of the Columbia Section was held in Spokane, Wash., Jan. 10, 1918, for the purpose of organizing and nominating members to the principal committees of the Section. Present: J. C. Haas, Vice-chairman; W. H. Linney, Past Chairman; and L. K. Armstrong, Secretary. J. F. McCarthy, Wallace, Idaho, was appointed fifth member of the Executive Committee. The following were appointed to the Membership Committee: R. M. Betts; for Oregon; W. J. Hall, for Idaho; J. M. Porter, for Washington. A member for British Columbia will be appointed later. The following were appointed to the Committee on Papers: Prof. F. A. Thomson, Moscow, Idaho; Prof. L. 0. Howard, Pullman, Wash.; H. S. Lee, Rye Valley, Ore. A fourth member, representing British Columbia, is to be appointed later. The following members were appointed representatives on the Executive Committee of the Spokane Engineering and Technical Association: J. C. Haas, W. H. Linney, F. A. Ross, L. K. Armstrong. The Treasurer reported a deficit, resulting from the participation of the Section at the Northwest Mining Convention in 1916. It was recommended that the Institute be petitioned to make good this deficit, in addition to the usual annual allowance. The members of the committee who were present expressed their desire to be of greater service in the present war, and discussed at some length the possible means of carrying out their desires. It was later decided to reopen the subject at a subsequent meeting of the Section, or to present it to the Executive Committee of the Spokane Engineering and Technical Association for discussion and cooperative action. L. K. ARMSTRONG, Secretary.

Jan 3, 1918

By Samuel Shallcross

TO principal function of the Bell limestone mine, of the American Lime & Stone Co., at Bellefonte, Pa., is to supply raw material to the company's modern rotary kiln plant at Bellefonte. Because mining costs are naturally higher than many open quarries with more favorably lying strata, it cannot compete, except to a limited extent, in the markets for road material and fluxing stone. In the broad sense, mining does have an advantage over the average open quarry when the end products are designed for and controlled by process and final inspection for the exacting demands of the industrial and chemical markets. Approximately 80 per cent of the output of the Bell mine is sold in the industrial and chemical markets. And as higher standards are set each year for construction and agricultural work, the remainder of the mine output goes to these two classes. Mining produces more fines than open quarries, and these fines are difficult to market; on the other hand, owing to absence of contaminating clay and impure rock, a greater percentage of the output of a mine is marketable. Because of the great production of fines, rotary kilns for lime burning are necessary when the stone must be mined. In 1921 the American Lime & Stone Co. operated 19 quarries and 72 lime shaft kilns spread over an area of 40 miles between Bellefonte and Altoona, Pa. At that time the lime-production capacity of the 72 kilns amounted to approximately 700 tons per day. After 15 years the company operates three rotary kilns and six shaft kilns, with a combined output of approximately 500 tons of lime per day, concentrated in its single Bellefonte plant (Fig. 1). Its only stone-producing plants are now the limestone mine at Bellefonte and a construction-stone open quarry at Union Furnace, near Tyrone, Pennsylvania.

Jan 1, 1936

By A. H. Geisler

The correlation of property changes during precipitation with structure has progressed, sometimes rapidly but other times more slowly, since the fundamental discovery of Merica, waltenberg and Scott.1 The predominent factor that hampered the progress has been limitations imposed by the various detection methods. Refiments in x ray diffraction tech-niques and in metallographic methods, which have been extended by the electron microscope, have contributed new information within the last few years. These permit an extension of the theory as proposed by Mehl and Jetter in 1940'2 Now that a sufficient number of alloys has been investigated to establish a general mechanism of the precipitation process, a correlation of the facts into a generally applicable theory of age-hardening is both warranted and desirable. The purpose of the paper is to provide an orderly correlation of the phenomenological facts of precipitation hardening. Speculation 011 mechanism of hardening will be confined to that consistent with existing theories of hardening, Age-hardening accompanies the formation of a new structure, the precipitate, as provided by a11 alloy system ill which solid solubility decreases with decreasing temperature. Upon this premise alone all such systems would be expected to include age-hardenable alloys. Alas, this is not always the case. Few attempts have been made to explain the variable degree of age-hardening among different alloys or to explain the influence of small alloying additions upon the hardening. Dispersion hardening as originally postulated3 is not adequate.* Coherency hardening—the term that will be used to distinguish the properties of a two-phase mixture in the unique and unstable transition state at which the phases are strained into precise atomic registry (continuity or coherency) in planes

Jan 1, 1949

By Benj. N. Webber

There is a broad analogy between super gene nickel deposits and super gene copper deposits of the porphyry type. Some of the nomenclature of supergene copper may he applied to super gene nickel deposits. The obvious connection between lateritization and supergene nickel concentration requires some clarification of the nomenclature of laterite of ultrabasic rock parentage. Lateritization is a progressive process and the transition products of the laterite profile are a key to the process of nickel concentration since the profile grades from unaltered peridotite to the highly ferruginous ultimate laterite capping. This profile is formed under highly restricted geographic and geologic conditions. Faulting contributes to the formation and localization of the higher grade commercial segregations of nickel. That there may be auxiliary sources of nickel other than olivine is suggested. The volume of peridotite necessary to produce a unit of laterite at any point in a complete profile is calculated on the basis of the chromite content. The lixiviation, transportation, and precipitation of the elements involved is considered and the source of the reagents and chemical mechanisms are suggested. The role of sodium chloride is considered important. The progressive changes in the lateritic profile have an effect on the general process since lateritization takes place in overlapping environmental phases. The mineralogy of laterite and the redistribution of elements is illustrated by compositional curves derived from a completely mature laterite. Nickel scanvenged by iron oxides tends to be redissolved and moves downward to the zone of transitional magnesium silicates where it is reprecipitated. The geometry of the nickel enrichment zone is simple in general, but complicated in detail. Elongated pods of a greater concentration of nickel are indicated to be a reflection of faulting. Lateritization and concentration of nickel may be arrested at any stage and be modified by several factors.

Jan 1, 1973

By R. F. W. Pease, R. A. Ploc

A scanning electron microscope with a resolving power better then 100Å has been developed for the direct examination of surfaces. This instrument was used to study iron undergoing oxidation at 500°C. It was found that the electron current in the scanning electron microscope was low enough (about 10-atrzp) to have no observable effect on the growth of the oxide. "Armco " iron, when oxidized, exhibited an oxide film whose thickness and whiskey population varied with pain orientation; but purer iron, when oxidized, exhibited no such pain dependence and whisker occurrence appeared to be caused by impurities. UNTIL recently most surfaces of opaque specimens could either be studied with a light microscope or, if higher resolution was required, by viewing a replica of the surface in a transmission electron microscope. Direct electron microscopy of a surface has, in general, proved difficult owing to excessive foreshortening and the poor image quality obtained. The scanning electron microscope, however, offers an alternative method of directly viewing a surface without these disadvantages. At low magnification it offers a much larger depth of focus than the light microscope, and at high magnifications it offers much higher resolution (about 100Å). PRINCIPLE OF THE SCANNING ELECTRON MICROSCOPE A schematic diagram is shown in Fig. 1. The electron optical system consists of a gun followed by a series of lenses which focus the electron beam onto the surface of the specimen. The beam is scanned in a rectangular raster across the specimen surface and, by amplifying the secondary electron current from the 'pecimen, a picture of the specimen surface is built UP sequentially on the face of the display cathode-ray tube. The magnification of such a system is given by the ratio of the scan amplitude on the display cathode-ray tube to

Jan 1, 1965

By George Boulter

Draglines 8.2-1 Introduction. The nature and characteristics of rock and rock derivatives forming the crust of the earth vary so greatly from place to place that it is impossible to use the same numerical factors to show the, productive ability of excavating equipment on different jobs or projects. Factors for each project must be developed individually and applied as the conditions and requirements dictate. TYPES' OF DRAGLINES. Types of draglines are differentiated by the propelling method used and are generally divided into four classes, as follows: 1. Wagon mounted 3. Crawler mounted 2. Truck mounted 4. Walking Figure 8.2-1 shows a truck-mounted dragline. This type is considered to be the most mobile unit. In order to increase stability over the side, outriggers are installed as part of the truck chassis. This feature is not shown in .this figure. Figure 8.2-2 shows a crawler-mounted dragline. The long, wide crawlers are used to increase the stability and reduce the bearing pressure of this unit. These features allow for use of these units on surfaces too soft for the wagon- or truck-mounted types. Figure 8.2-3 shows a walking-type dragline. The large diameter tub and the well-supported boom through the gantry gives high stability for rugged works over a long life. BASIC PARTS OF A DRAGLINE. The basic parts of a dragline are illustrated in Fig. 8.2-4. A deck layout is shown in Fig. 8.2-5 with the main components named. OPERATION OF A DRAGLINE. Following is a description of the steps and controls present in a typical cycle of operation of a large dragline having independent hoist and drag motors. Starting the cycle with positioning the bucket on the ground under the point of the boom, the next step is

Jan 1, 1968

By S. Le Fevre

THE application of electricity to the mining and beneficiation of the magnetic iron ores of the Mineville, N. Y., district, on Lake Champlain, has resulted in economies and enhanced quality of product, without which only a comparatively small quantity of the present output could be marketed. The output of the Witherbee, Sherman & Co. mines is about 700,000 tons per annum, and of this about four-fifths is treated by magnetic separation to increase the iron content and reduce the phosphorus. The use of electricity for the magnetic separation of the ore from the gangue is therefore of primary importance, and makes possible the application of electric power for mining and preparing the ore for concentration: The fact which speaks loudest in favor of the application of electricity is this: It is possible for about 25c. per ton of shipping ore to furnish all the power required to put the ore on cars. This includes mining a hard ore underground, from a depth of 900 ft., hoisting to surface, crushing to 4 or s in. in size, and separating from the gangue. This also includes lights about the works, and all miscellaneous power, such as about the shops. The first plant for the generation of electric power for use at Mineville was completed in 1903, and was one of the first for the application of electricity to mining iron ore. This was a Nordberg compound condensing steam engine, direct connected to a 750-kw. alternating-current generator, 3,300 volts, 3 phase, 25 cycles. All the plants added later use the same-current but with higher voltage. The map, Fig. 1, shows the power plants and the transmission system; Figs. 2 and 3 are views of the shaft houses and the mills.

Jan 6, 1914

By H. W. Morse

The experimental work on the oxidized copper ore at the New Cornelia mine at Ajo, Ariz., ended on Jan. 12, 1916. On that date final decision was made on the general nature of the process to be used in the 5,000-ton leaching plant, and on many of the details, as far as experience on a 40-ton scale could decide them. With the approval of the Board of Directors and the General Manager, John C. Greenway, we have compiled what seem to be the most interesting data on the results obtained during the experimental period. The most important part of the data resulted from the operation of a 1-ton and a 40-ton plant at Ajo. Experimental work on Cornelia oxidized ore dates back to April, 1912, and has been going on nearly continuously since that time. A good many variations from the original idea have been tried, but the process finally decided upon is in principle and in all of its details a simple one. The history of the leaching work on this ore has been brought down to about a year ago in papers presented to this Institute by Stuart Croasdalel and Dr. L. D. Ricketts.2 The present paper will, therefore, deal principally with the results obtained during the last year of the work. Preliminary Tests by Mb. Croasdale Preliminary tests were begun by Stuart Croasdale in July, 1912. A number of important points were definitely decided by his work. Among these were: 1. New Cornelia oxidized ore, not very finely crushed (to about 2-to 3-mesh) showed good extraction with 5 per cent. sulphuric acid. It appeared that better than 80 per cent. extraction could be expected. 2. The consumption of acid for this extraction was not prohibitive. It was apparently 3.5 to 4 1b. gross per pound of copper recovered.

Jan 1, 1917

By Christopher H. Bierbaum

The first significant fact observed in the study of bearing metals is that not a single pure homogeneous metal has given satisfactory service; all bearing metals are alloys made up of two or more phases; that is, they consist of hard and of relatively soft microscopic particles intimately mixed. The function of the hard particles, or bearing crystals, is to support the load and resist the wear when actual metallic contact exists between the bearing surfaces. The functions of the softer particles are to allow the harder particles to adjust themselves to the surface requireinents of the journal and to wear down slightly below the surface of the harder, forming slight depressions on the apparently smooth wearing surface of the bearing, in which some of the lubricant is held when the bearing surfaces are brought into contact with each other. It is this characteristic of certain alloys to form these slight depressions, and thus provide the means for retaining a lubricant, that characterizes them as true bearing metals; in fact, a bearing metal has been defined as "an alloy that is capable of retaining a lubricant upon a bearing surface."' The extent to which the lubricant can be so held determines the most valuable characteristic of an alloy as a bearing metal. An alloy which, perhaps, most characteristically represents a bearing metal is the composition of copper and tin that contains sufficient tin to produce the tin-copper eutectoid, or delta crystal. The depressions worn upon the surfaces of the softer crystals of the teeth of a motor-truck worm wheel, made of an ll-per cent. tin bronze, in many cases were from 5 to 6 microns in depth; all other conditions remaining constant, this depth of wear increases with an increase of working pressure. This copper-tin bronze contains intercrystalline shrinkage cavities, which also

Jan 1, 1923

By Albert Sauveur

The following propositions and corollaries are intended to present, as concisely as possible, some of the evidences gathered while studying the microstructure of steel. Each proposition is accompanied by photo-micrographs showing the structure of illustrative samples. But it must be understood that the special instances thus chosen for illustration are by no means the only ones on the examination of which the propositions are based. On the contrary, they have been taken almost at random among a great many, in some instances more than a hundred, similar cases. Proposition I. A slow and undisturbed cooling from a temperature x or higher produces crystallization. Plate L, Plate II., Fig. 1, and Plate V., Figs. 1, 2, 3 and 4 show the crystalline structure of several pieces of steel. Plate I. reveals this structure in the center of a slowly-cooled Bessemer ingot, 1.5 feet from the top. Plate II., Pig. 1, is from a small 2-in, square testingot of the same heat, slowly cooled. Plate V., Figs. 1, 2, 3 and 4 show the structure of different parts of steel rails. The original photographs were all magnified 70 diameters, and have been reduced in engraving to 63, or to 55 diameters, as shown in the plates. Proposition 11. Undisturbed cooling from an initial temperature lower than x is not accompanied by crystallization. Plate III., Fig. 5, shows the structure of a piece of rail-steel forged from a white heat until it had fallen to dull-red. The structure is almost amorphous. Practically no crystallization has taken place during the subsequent cooling. Corollary.—Pieces of steel finished at a temperature lower than x do not take a crystalline structure.

Jan 1, 1894

By Henry M. Howe

The brilliant and very original matter in Professor Jeffries' discussion† should rank not only as an independent paper, but as a most important one. In particular, the explanation which it gives of the remarkable Sauveur phenomenon, over which so many of us have puzzled long and hard, is so clear, complete, and cogent as to go far toward establishing Professor Jeffries' hypothesis. The very leatures of Professor Sauveur's photographs which fit this hypothesis so exactly are reproduced in Chap-pell's photographs of steel coarsened under somewhat different conditions.' The ideas developed by these discoveries are so novel that convenicnce of language seems to call for new conventional terms for expressing them. In what follows here I propose certain terms for this end, for criticism and improvement, and I attempt to generalize from Professor Jeffries' hypotheses. Generally speaking, a given set of grains which undergo no growth in the cold will, when the temperature is raised progrcssively, start to grow on reaching a certain temperature, and will continue growing at all higher temperatures. The "germinative" temperature is that at which growth begins, quite as the conditions which cause a seed to grow are "germinative." We have then an inert temperature range below the germinative temperature, and a growth range above it, the germinative temperature being the limit between these two ranges. So, too, a germinant grain is one which is at its germinative temperature, and hence beginning to grow, while inert grains are those below their own germinative temperature, and the term "growing grains" includes those which are germinant and those which are above their germinative temperature. These last could be called " supergerminant" if the distinction should be needed. "Germinative temperature" seems better than "critical temperature

Jan 1, 1917

By James C. Ray

The age classification of the mineralized veins of the Butte district, as given by Weed and Sales, was tacitly accepted for many years. Weed, whose field work was completed in 1906, divided the copper veins into groups of four ages.' In 1913, Sales modified Weed's classification and assigned all mineralized veins (including the silver-zinc veins of the border or "peripheral" zones) to three periods of fracturing and mineralization. Both writers based their classifications mainly on the relative ages of the observable faulting whereby the veins of a so-called "earlier" system are intersected and offset by those of a "later" system. Nevertheless they possess structural and mineralogical characteristics in common which indicate that they are of the same age. The writer has maintained since 19143 that these vein systems were formed during one general period of mineralization along a network of intersecting fractures of approximately simultaneous origin and that the existing offsets are largely due to postmineral faulting. Leith,* takes cognizance of the accumulating mass of data relative to the simultaneous formation of intersecting fracture systems and says, referring to ~utte: "It now appears that the mineralization accompanying them (individual structure systems into which the veins have been grouped) is substantially of one period, indicating that the successive structural movements took place mainly within the period of mineralization." This paper presents the results of certain structural experiments which suggest a modified interpretation of the published data on the Butte district. The interpretation is substantiated by the writer's observations in the Butte mines and is offered with the hope that it will reconcile the structural with the mineralogical conditions existing in this most interesting district; also, that it will emphasize the importance of a

Jan 1, 1931