Search Documents

By Walter Miller

Although confident of its ability to meet any demands that may be made, the petroleum-refining industry is not complacent about the situation and realizes that the quantities of petroleum products to be furnished are so enormous and so far beyond what was previously estimated that the full cooperative effort of the industry must be exerted. Establishment by the President in May of the Office of Petroleum Coordinator for Defense with Secretary of the Interior Ickes at its head, plus the formation of the Petroleum Industry Council for Defense, in November, provide the channels for united endeavor within the industry and the means for gearing that endeavor in full harmony with the nation's needs. Great strides have been made and a rapid understanding of the situation and the magnitude of the task is being attained by all concerned. Refining, by constant study and development, by willingness to experiment and install new processes, and to replace older plants with more efficient equipment, had kept on a high plane of efficiency and progress. Working under the free competitive system, it built up its establishments until, as expressed in last year's report, it was easily able to supply any domestic demand that might be placed on it. Turning the United States into the arsenal not only of itself but of the united nations resisting aggression, however, in- creased the call for practically all petroleum products and in particular 100-octane aviation gasoline and high-viscosity aviation lubricating oils. Refining Capacity With over four million barrels a day of crude oil being charged to stills at the year's end, oil refining had broken all records and faced the necessity of further increasing its size to supply the ever-increasing demand for products, some of which, like 100-octane aviation gasoline, were research laboratory curiosities a few years ago. Although the refining capacity of the United States is listed at 4,860,000 bbl., about 800,000 bbl. of this is economically unavailable because of plant location or type. To meet the increasing needs, additional capacity of another half million barrels may have to be built in suitable locations and designed with an eye toward maximum production of aviation gasoline but with inherent flexibility to make it possible to vary and interchange with production of motor gasoline, furnace oils, and other products as necessity dictates. An interesting side light on this refining capacity question was an enquiry from official Washington for knowledge as to any idle refineries of something of the order of 10,000-bbl. daily crude capacity that might be purchased for bodily removal to Russia. 100-Octane Aviation Gasoline Largest of the tasks confronting refiners at the year's end was that of raising

Jan 1, 1942

By Albert E. Reed

THE development of the modern high-speed vibrating screen, together with the increasing availability of long-lasting stainless-steel screen cloth for relatively fine-mesh separations, means that more screen circuits will be used in the future. It seems pertinent therefore to examine a few characteristics of screen-circuit products, and especially the points of difference as compared with products of classifier circuits. The most noticeable change that takes place when substituting screening for classification in a grinding circuit is a substantial drop in the circulating load, owing to the greater ease with which the "fines" leave the circuit. Where circulating loads of 500 to 600 per cent are considered fairly normal in classifier grinding circuits, the grinding circuit equipped with screens for equivalent work will have a circulating load of only 20 to 75 per cent. As a result, the products of screen circuits will show a minimum of overgrinding or sliming as compared with a classifier circuit. The desirability of this characteristic will naturally vary according to the metallurgical requirement in each case. Because screen separations make a sharper division according to particle size, the products of screen circuits can be expected to show greater crowding of particles near the point of separation. These changes in product characteristics are so important that other factors, both in the grinding and concentration processes must be adjusted if the operator is to take full advantage of the increased tonnages and higher efficiencies available to him through the use of the screen circuit. One factor that too often is overlooked when changing to screen circuits is the importance of adjusting the ball-mill or rod-mill charge, to compensate for: (I) increased tonnage of new feed, (2) decreased circulating load, or (3) more granular character of feed. These same factors should also be taken into consideration for their effect on the various types of concentration or flotation equipment that may follow the screen circuit. Over a period of years, this equipment has generally been designed and adjusted to the product of the classifier, therefore it seems obvious that some research on the adjustment and adaptation of concentrating and flotation equipment to screen-circuit products will be most profitable to the operators. To illustrate the points mentioned above, the results from three recent installations follow, with data on the comparative characteristics of screen and classifier circuits. A range of separation from 10 to 48 mesh has been chosen, using two general types of screening equipment and two types of classifiers. The first of the installations of which the results are to be examined is that of an iron-ore installation where eastern magnetite was being concentrated prior to sintering. Fig. I shows the original grinding circuit, using classification, while Fig. 2 shows the same circuit equipped with a

Jan 1, 1945

By D. M. Davidson

The drill sampling and evaluation of the Piney River ilmenite property was carried out during the early part of 1944 by E. J. Longyear Co., using the company's standard core-drill outfits to complete 44 holes to an average depth of IIO ft., from which were collected 1100 samples. The Piney River ilmenite-apatite lode is 25 miles north of Lynchburg, in Nelson and Amherst Counties, Virginia (Fig. I). Its elevation is about 900 ft. above sea level and it lies in the old pre-Cambrian complex of crystalline rocks that make up the Piedmont physiographic province lying east of the Blue Ridge Mountains. The terrain is gently rolling and well watered and is drained by the Piney and Tye Rivers, which are tributary to the James. Geology The Piney River ore body comprises the upper, weathered part of a tabular basic rock, which occurs in a large area of granite-gneiss. The section containing profitable ore is about 3000 ft. long. It is separated naturally by thinning, into northeastern and southwestern segments with widths of 300 and 100 ft. respectively. The dip averages 4.5° southeast but steepens locally (Figs. 2 and 3). The unaltered rock is an even, granular mixture of feldspar, ilmenite, and apatite, to which Watson1 gave the name Nelson-ite. The decomposed ore body, which is now being exploited by open cut, is a yellowish clay material in which black ilmenite and glassy apatite are the only conspicuous minerals. An economically important structural feature of the deposit is a banding of minerals coinciding with the dip and strike of the dike. This is more pronounced in the footwall of the northeastern part of the intrusive, where there is also a higher than average concentration of ilmenite. According to Watson,' the TiO2 content of the Nelsonites of this region ranges from 10 to 42 per cent, while P205 varies from 4 to 15 per cent. It is inexpedient at present to disclose exact metal content of the Piney River ore body; suffice it to say that the average tenor lies well within the extremes noted by Watson. Sampling Methods and Procedure During a preliminary inspection of the ore body, Longyear engineers surmised that because of its soft, clayey character, drill sampling would yield little core, therefore they made all possible preparations to procure accurate samples of the drill cuttings, or sludge. The first requisite in obtaining representative drill cuttings is to secure their full recovery. Only under certain conditions, and by employing a most careful and rigid sampling technique, is this pos sible. There must be no loss of the water circulating in the hole, and the velocity

Jan 1, 1949

By D. W. McGlashan, K. N. Mcleod

IN the use of free bubbles with precise temperature control and continuous pH measurement, the contact angle apparatus differs from all previous equipment. Experimental procedures differ sharply from the captive bubble method1,2 of introducing the gaseous phase in the three-phase system. When freed from the tube and captured by a solid surface, a bubble more closely conforms to the spherical ideal set up by the usual mathematical analysis of surface free energy or surface tensional relationships of the forces involved. The assembled equipment, Fig. 1, departs from the usual contact angle apparatus in providing: 1) water circulation for fixing temperature, 2) instruments to measure and record pH during testing, and 3) a system for producing and using free bubbles. The apparatus allows testing over a broad range of closely controlled conditions, and the use of free bubbles gives contact angles independent of operator manipulation, which was unavoidable in the older captive bubble method. A bubble released below the specimen rises through the liquid and contacts the mineral. If the mineral is gas-avid the bubble adheres, developing a finite contact angle. Reaction cells (1), 2x33/8x5 3/16 in. ID, are of pyrex glass 5 mm thick. To prevent optical distortion, the sides are optical flats and are planed parallel to within five wave lengths of light over the entire surface. Special cement is required to withstand chemical attack and thermal shock. The cell is placed in a thermal jacket (2) made of welded aluminum. A water seal for the optical ports is made by using O-rings tightened against the flats of the cell by fine-threaded and adjustable ports, Fig. 2. In-flow water is discharged downward from a manifold located near the bottom of the cell jacket. Water overflows the weirs at each end of the cell jacket, discharging from both sides to a collecting manifold (24). A hose (26) leads the overflow water to the thermal-conditioner well (4), which is recessed to accommodate a reaction cell and two beakers (150 ml). Both the thermal jacket and the thermal-conditioner well are insulated to minimize the effects of temperature differentials. Water, discharging from the thermal-conditioner well, returns to a thermostat bath and pump (3), from which it is pumped to the thermal jacket. The thermostat bath permits temperatures to be adjusted from 1" or 2°C to 80°C and will maintain the selected temperature within 0.2ºC. An electrode support (22) groups the four electrodes (8) so that they fit conveniently into the reaction cell, Fig. 2. This assembly holds the glass electrode, the calomel electrode, the temperature-

Jan 1, 1957

By Herbert A. Stein, John B. Murdock

AN analysis of perlite expansion furnaces must be based upon one consistent theory which explains how and why perlite does expand when heated. There is more than one such theory, so to establish a basis for the rest of this paper, the authors will outline one theory and the data that support it before going into the construction details of different furnaces. JOHN B. MURDOCK, Associate Member AIME, is President, and HERBERT A. STEIN is Secretary, of the Perlite Corp., Phoenix, Arizona. San Francisco Meeting, February 1949. TP 2736 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 3, 1949. Why Perlite Expands: Perlite is known to contain some dissolved or combined fluid, probably water, which is lost when the material is heated to fusion. It is generally agreed that when particles of this volcanic glass are heated to fusion in such a way that vaporization of this water into steam takes place at the same time as the glass becomes soft, the steam puffs up each particle into a mass of glass foam. It is a simple matter to expand perlite under a blow torch for demonstration purposes, but in commercial installations, the problem is made more complicated by the necessity of making efficient use of both raw material and fuel, and producing an expanded aggregate conforming to close specifications for size distribution and density, using many different types of perlite rock. The ability of a given operation to fulfill these requirements depends upon the proper handling of four variables. They are: (1) the nature of the perlite rock used, (2) the heating time taken to get the perlite particle up to its highest temperature, (3) the size of the particle, and (4) the maximum temperature the particle reaches. Types of Perlite Rock: Perlite may be classified in many ways, but the characteristics most easily correlated with its behavior in furnaces are its softening temperature, its effective water content, and its "liveliness." Actually there is a close correlation among these three characteristics so it is possible to describe a perlite using any one of them. Lively perlites always have low softening temperatures and high effective water contents, whereas the deader perlites have higher softening temperatures and lower effective water contents. These softening temperatures run from 1400°F to above 2000°F and the effective water contents run from over 2 pct down to 0.2 pct. Included in the category of lively glasses are the green pitchstone from the Edgar claim in Superior, Ariz., the red pitchstone on the Animas highway south of Lordsburg, N. Mex., and a gray glass from Beatty, Nevada. Examples of intermediate perlites (in order of decreasing liveliness) are the Guzman-Lobb perlite with obsidian

Jan 1, 1951

By Herbert A. Stein, John B. Murdock

AN analysis of perlite expansion furnaces must be based upon one consistent theory which explains how and why perlite does expand when heated. There is more than one such theory, so to establish a basis for the rest of this paper, the authors will outline one theory and the data that support it before going into the construction details of different furnaces. JOHN B. MURDOCK, Associate Member AIME, is President, and HERBERT A. STEIN is Secretary, of the Perlite Corp., Phoenix, Arizona. San Francisco Meeting, February 1949. TP 2736 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 3, 1949. Why Perlite Expands: Perlite is known to contain some dissolved or combined fluid, probably water, which is lost when the material is heated to fusion. It is generally agreed that when particles of this volcanic glass are heated to fusion in such a way that vaporization of this water into steam takes place at the same time as the glass becomes soft, the steam puffs up each particle into a mass of glass foam. It is a simple matter to expand perlite under a blow torch for demonstration purposes, but in commercial installations, the problem is made more complicated by the necessity of making efficient use of both raw material and fuel, and producing an expanded aggregate conforming to close specifications for size distribution and density, using many different types of perlite rock. The ability of a given operation to fulfill these requirements depends upon the proper handling of four variables. They are: (1) the nature of the perlite rock used, (2) the heating time taken to get the perlite particle up to its highest temperature, (3) the size of the particle, and (4) the maximum temperature the particle reaches. Types of Perlite Rock: Perlite may be classified in many ways, but the characteristics most easily correlated with its behavior in furnaces are its softening temperature, its effective water content, and its "liveliness." Actually there is a close correlation among these three characteristics so it is possible to describe a perlite using any one of them. Lively perlites always have low softening temperatures and high effective water contents, whereas the deader perlites have higher softening temperatures and lower effective water contents. These softening temperatures run from 1400°F to above 2000°F and the effective water contents run from over 2 pct down to 0.2 pct. Included in the category of lively glasses are the green pitchstone from the Edgar claim in Superior, Ariz., the red pitchstone on the Animas highway south of Lordsburg, N. Mex., and a gray glass from Beatty, Nevada. Examples of intermediate perlites (in order of decreasing liveliness) are the Guzman-Lobb perlite with obsidian

Jan 1, 1951

By R. T. Webber, B. B. Owen

THE vapor phase deposition of molybdenum and tungsten from the hexacarbonyls has been thoroughly investigated by Lander and Germer1 and shown to yield well-bonded coatings on a variety of hot metallic surfaces. They also demonstrated that chromium coatings2.3 could be similarly deposited, but did not investigate this metal extensively. Recently,4 conditions have been described by which this compound can be prepared in quantities sufficient for laboratory scale plating experiments, and it is the purpose of the present communication to outline the results of preliminary experiments upon the plating of chromium from its carbonyl. APPARATUS AND TECHNIQUE The apparatus used in these experiments is shown in Fig I. At one end, connected by a short length of rubber tubing, is a Cenco Hypervac 20 pumping continuously. At the opposite end is a needle valve which allows a small stream of purified hydrogen to flow through the apparatus. Connected in series are a trap T1, maintained at the temperature of dry ice and acetone, the plating chamber, and two traps T2 and T3 containing crystals of the carbonyl. T2 is kept in a constant temperature bath (not shown), while T3 is at room temperature. Stopcock S6 allows the hydrogen flow to by-pass the carbonyl traps. A McLeod gauge is connected so that it can measure the pressure at the pump through Ss, or the pressure at the plating chamber through S9 and S6. The standard (12 liter) volume connected by S5 is used to determine the volume included by S4, S6, Se, S10, the needle valve and the McLeod gauge. Knowledge of this volume allows calibration of the flow of hydrogen. The apparatus* is built entirely of pyrex, except for the needle valve, the rubber connection to the Hypervac, and the cover of the plating chamber. The plating chamber is water-jacketed, with a large brass top allowing insertion of the specimen to be plated. Set into the brass top is a ground glass stopper through which thermocouple leads are sealed. The thermocouple wires (pure Pt, and 87 pct Pt-13 pct Rh) serve the double purpose of measuring the specimen temperature and suspending it in the chamber. Surrounding the chamber is the coil of an induction heater, H. The apparatus is designed to allow variation of the following conditions: I, the specimen temperature, from room temperature to about 1000°C, 2, the carbonyl vapor pressure, from 40 to 220 microns, and 3, the hydrogen flow. In several runs, 0.8 to 1.8 pct of hydrogen sulfide was introduced through a needle valve that replaced S4. The vapor pressure of the carbonyl is

Jan 1, 1948

By William G. [Peryam], Bishop Ottey M., Fred E. Johnson

THE Lepanto Consolidated Mining Company is the largest copper producer in the Philippines, and the only one that makes a concentrate valuable principally for its copper; also, it has the only productive copper mine situated at considerable distance from the sea, and is the only one in the islands operating its own smelter. The Lepanto mine is in the Municipal District of Mankayan, sub-province of Benguet, near the heart of the Mountain Province of Northern Luzon. It is 165 km. from its shipping point at San Fernando, Province of La Union, on the shore of the China Sea. Elevations at the property range from 3200 to 4500 ft. The climate is very mild; temperatures are seldom below 50° or above 80°F. Annual rainfall approaches 170 in. and is mainly confined to a rainy season lasting from May to October. The months from December to April, inclusive, are usually extremely dry. This climatic pecularity entails the problems of landslides on the roads during the rainy season and water shortage during the dry season. The Mountain Trail, an improved rock-surfaced toll road maintained by the Commonwealth Government, gives access to the property. The 105 km. over this road may be traveled in about 4 ½ hr. during the dry season. Very few sections of the road are straight for more than 100 meters, and about one third of it is a one-way road controlled by gates. All freight for the property is delivered by the Manila Railroad Company to Bauang, La Union, 45 km. west of Baguio and at sea level, where it is picked up by freight trucks and hauled via Baguio to Lepanto. Granulated matte is hauled in bulk from Lepanto in four-ton lots on freight trucks to the storage bins at San Fernando. Freight rates from Bauang to the property amount to P8.00 per ton, and from the property to San Fernando the rate is P16.00 per ton. The company pays the road toll, P1.00 per truck, each way. THE CAMP The company maintains a modern camp, well separated from the mine and reduction plant. Comfortable and sanitary living quarters, water, and light, as well as free medical service are provided all employees. A hospital staffed by a doctor and two nurses takes care of all medical treatment. Considering recreational facilities of great importance, the company has provided two tennis courts, two basketball courts, and badminton courts for employees. Bowling alleys and a motion picture theater are operated by the company, the profits being expended for other recreational purposes. A moderate sized recreation hall serves for barrio dances, meetings,

Jan 1, 1942

By T. I Harkins, J. Brian Eby

This paper outlines the geophysical investigation of the area covering the Darrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The Darrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook1 and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outline and comes to within about 4625 ft. of the surface. At this depth the diameter of the salt plug is approximately 4800 ft. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The line showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable. Surveys with Refraction Seishograph and Torsion Balance A reported oil show in a water well drew attention to the lands of the Belle Helene

Jan 1, 1943

By R. T. Webber, R. B. Owen

The vapor phase deposition of molybdenum and tungsten from the hexacar-bonyls has been thoroughly investigated by Lander and Germerl, and shown to yield well-bonded coatings on a variety of hot metallic surfaces. They also demonstrated that chromium coatings2'3 could be similarly deposited, but did not investigate this metal extensively. Recently, conditions have been described by which this compound can be prepared in quantities sufficient for laboratory scale plating experiments, and it is the purpose of the present communication to outline the results of preliminary experiments upon the plating of chromium from its carbonyl. Apparatus and Technique The apparatus used in these experiments is shown in Fig I. At one end, connected by a short length of rubber tubing, is a Cenco Hypervac 20 pumping continuously. At the opposite end is a needle valve which allows a small stream of purified hydrogen to flow through the apparatus. Connected in series are a trap T1, maintained at the temperature of dry ice and acetone, the plating chamber, and two traps T² and T3 containing crystals of the carbonyl. T² is kept in a constant temperature bath (not shown), while T³ is at room temperature. Stopcock S6 allows the hydrogen flow to by-pass the carbonyl traps. A McLeod gauge is connected so that it can measure the pressure at the pump through Se, or the pressure at the plating chamber through S9 and S6. The standard (12 liter) volume connected by Sb is used to determine the volume included by S4, S6, SB, Slot the needle valve and the McLeod gauge. Knowledge of this volume allows calibration of the flow of hydrogen. The apparatus* is built entirely of pyrex, except for the needle valve, the rubber connection to the Hypervac, and the cover of the plating chamber. The plating chamber is water-jacketed, with a large brass top allowing insertion of the specimen to be plated. Set into the brass top is a ground glass stopper through which thermocouple leads are sealed. The thermocouple wires (pure Pt, and 87 pct Pt-13 pct Rh) serve the double purpose of measuring the specimen temperature and suspending it in the chamber. Surrounding the chamber is the coil of an induction heater, H. The apparatus is designed to allow variation of the following conditions: (I) the specimen temperature, from room temperature to about 1000°C, (2) the carbonyl vapor pressure, from 40 to 220 microns, and (3) the hydrogen flow. In several runs, 0.8 to 1.8 PCt of hydrogen sulfide was introuced through a needle valve that replaced S4. The vapor pressure of the carbonyl is

Jan 1, 1949

By J. Brian Eby, T. I. Harkins

This paper outlines the geophysical investigation of the area covering the Darrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The Darrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook1 and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outline and comes to within about 4625 ft. of the surface. At this depth the diameter of the salt plug is approximately 4800 ft. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The line showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable. Surveys with Refraction Seishograph and Torsion Balance A reported oil show in a water well drew attention to the lands of the Belle Helene

Jan 1, 1943

By Ray Hammond Misener

THE purpose of this paper is to describe the installation of the pumping station on the 3314-ft. level of the Carlos Francisco mine of the Sociedad Minera Backus y Johnston del Peru, at Casapalca, Peru. However, so much preliminary work was necessary before the actual installation could be started that some of that work will be described briefly, in order to clarify the discussion of the main subject. The Sociedad Minera Backus y Johnston del Peru, a subsidiary of the Cerro de Pasco Copper Corporation, owns and operates a group of mines in the Casapalca district, of which the most important are the Carlos Francisco and the Aguas Calientes. These two mines, one mile apart, are connected on their 2100 and 2700-ft. levels. These are motor-haulage levels, equipped with 3 ½ -ton Baldwin-Westinghouse locomotives operating from a 260-volt d.c. overhead trolley. A 38-cu. ft. hopper-bottom car is used. Each mine has a 2 ½ -compartment, inclined (70°) winze shaft. The Aguas Calientes shaft, operating between its 2100 and 2900-ft. levels, is used only for men and materials; whereas the Carlos Francisco shaft, between the 1700 and 2700-ft. levels of that mine, is the main operating shaft for the district. All the ore from the Carlos Francisco and the Aguas Calientes mines is hoisted through the Carlos Francisco shaft. The ore produced in these mines is by-passed to the 2700-ft. level, where it is gathered by the electric trains, taken to the Carlos Francisco shaft and dumped into an ore pocket in front of the shaft. The ore is hoisted to the 1700-ft. level in 2-ton self-dumping skips and emptied into a 150-ton loading pocket. There it is loaded into electric trains and despatched to the concentrator through the Backus and Johnston tunnel, which is the main entry from Casapalca to all the mines in the Backus and Johnston group. DEVELOPMENT PROGRAM In 1934 the following development program was outlined for the Carlos Francisco and the Aguas Calientes mines: (1) to deepen the Carlos Francisco shaft from the 2700 to the 3400-ft. level, (2) to deepen the Aguas Calientes shaft from the 2900 to the 3300-ft. level, and (3) to connect the two shafts on the 3300-ft. level with a motor-haulage crosscut. Each mine was to be developed also on intermediate levels (2900 and 3100). The three levels were to be spaced 54 meters (177 ft.) floor to floor, measuring from the 2700-ft. level along the incline of the shaft. The Carlos Francisco mine, together with the section between it and the Aguas Calientes mine, produces 10,000 gal. of water per minute. A fault to the north

Jan 1, 1943

By Donald W. Scott, Adam Wesner

This paper describes the study of 23 nonmagnetic iron-formation samples from the Mesabi Range and shows the significance of their chemical, mineral, and physical properties in terms of their concentration. Data presented here resulted from a research project carried out from 1942 to 1952 by 10 major producers of iron ore, working in conjunction with Battelle Memorial Institute. THE inevitable depletion of Mesabi direct-shipping iron ores, hastened by recent wars, has increased the importance of developing methods to concentrate iron-formation materials. Many mining companies, independent research organizations, chemical companies, and equipment manufacturers are devoting attention to this important work. It is only natural that magnetic iron-formation materials have received major emphasis, since magnetic recovery methods apply and reserves of Mesabi magnetic taconites are large. However, the nonmagnetic* iron-formation materials are likewise believed to represent a large reserve and their study has not been neglected. tions over the years have shown that in addition to the unenriched taconite, which is dense and hard, and the direct-shipping ore, there are transition taconites grading into the friable wash, or intermediate ores. The transition taconites are less massive than the unaltered taconites and usually coarser-grained. This variation, coupled with the fact that there were no extensive drillings in the unaltered taconite, posed a most difficult problem of obtaining samples that would be representative of large tonnages of the fresh rock. The problem was increased by the tremendous extension of the nonmagnetic formation materials on the Mesabi and by the question of their accessibility to mining. A drilling program was evolved that would surmount these difficulties. Selection of samples was made by a committee representing producers in the area. The samples were procured from 1—taconite walls near bodies of stripping burden or wash ore and 2—from shafts in the process of being sunk through taconite for drainage or mining operations. Most of the samples were obtained from the cherty horizons because it became obvious early in the program that the slaty horizons represented an exceedingly difficult concentration problem, owing to the character of the gangue minerals and the fine grind required for liberation of the valuable minerals. More samples were procured from the lower cherty horizon than from the upper cherty because it was more accessible to mining. It is not known how well the samples selected represent the nonmagnetic iron-formation material. However, they were chosen by people Well acquainted with the geology of the Mesabi range and the mining problems involved. It is believed that they represent a fair cross-section of the types of materials that will be encountered. Table I gives data on the origin of the 23 samples and the horizon footages from which they were obtained. Samples 1 through 10, and 15 and 16

Jan 1, 1955

By William D. Klopp, Joseph R. Stephens

Chromium alloys were coated with silicon, alumi-nuw, and boron by pack cementation. None of these simple coatings provided adequate nitridation/oxida-tion protection for a Cr -0.17pct Y alloy substrate as shown by a substantial Increase in the ductile -brittle transition temperature after air exposure for 100 hr at 2100°F. Iron-modified silicide coatings afforded good protection, holding the transition temperature of air-exposed specimens to 350° F compared to 200° F for uncoated unexposed specimens and 800°F for un-coated exposed specimens. Additional attractive cant-binations of modi-tying elements included Fe-mo, Fe-Mo-W, Fe-,Mo-W-Ti, and V-Mo-W-Ti. THE desirability of increased operating tempera-tures as a mcans of improving the performance of ad-vanced air breathing engines has resulted in emphasis on the development of materials with high operating temperature capabilities. Chromium, because of its relatively low density (7.19 g per cu cm), high melt-ing point (3410°F), and adequate strength upon alloy-ing, is a candidate material for turbine buckets and stator vanes of advanced air breathing engines. How-even, chromium is not without severe limitations, the major one being susceptibility to nitrogen embrittle-ment upon exposure to air at high temperatures.1,2 For example, a 25-hr air exposure of a Cr-5 pct W* * All compositions in wt pct. alloy at 2100°F produces a 600°F increase in the duc-tile-brittle transition temperature.' Although dilute alloying with such elements as yttrium, lanthanum, arid thorium3,4 or strong nitride formers5 has been shown capable of reducing nitrogen embrittlement, it is apparent that some additional form of surface protection, such as coatings or claddings, will be required for long time service in air breathing engines. Studies of aluiminide6 and silicide7 coatings and of nickel-base claddingsl on chromium alloys to date have suggested that these protection systems are inadequate. Of the aluminidc systems Studied,6 a simple aluminum and an Fe-Al coating on a Cr-5 pct W-0.1 pct Y alloy showed the lowest air exposure weight gains. However, the air exposures raised the ductile-brittle transition temperature of the coated specimens to above 1600°F from an initial level in unexposed specimens of about 500°F. A second in-vestigation for protection of Cr-5 pct W-0.1 pct Y employed gas pressure bonded alloy foils as protective claddings.1 An aluminized Ni-20 pct Cr-20 pct W alloy plus an unalloyed tungsten barrier layer gave the best performance with air exposure lives based on appearance and weight gains of over 600 hr at 2100°F. However, the bend ductile-brittle transition tempera-ture was increased to at least 1000°F after 100 hr at

Jan 1, 1970

By George Sachs

I deeply appreciate the honor of being selected to deliver the twentieth Annual Lecture of the Institute of Metals Division. The subject of my paper is extremely involved and voluminous, therefore I shall discuss only some more recent experimental material and speculate somewhat on the physical and mechanical fundamentals of these changes. The flow and the rupture of a solid material are rather different phenomena. It is therefore surprising that up to a rather advanced stage in metallurgical science these two fundamental phenomena have been simultaneously treated and forced into the general conception of the "failure " of solid material. Only in this century, and particularly during the last 20 years, have the very different physical meanings of flow and rupture been clearly recognized. Several hundred of the more recent publications deal with these subjects.l Law of Similarity The basic values commonly considered responsible for the mechanical behavior of any material are the stresses. From this standpoint both a large and a small article made from the same homogeneous metal and of geometrically similar shapes should behave identically, i.e., they should deform geometrically in a similar manner, if subjected to the same stress values at corresponding points. This "law of similarity" was introduced about 60 years ago simul- taneously by Barba2 and Kick3 and was derived from the classical theory of elasticity. As far as the plastic behavior of a metal is concerned, this rule appears to be valid. The conventional properties of large and small tension or compression test bars, machined from larger sections, are identical; while the force required to deform a section is proportional to its cross-sectional area and the work consumed in deforming geometrically similar articles in a geometrically similar manner is proportional to its volume. The general trend of the stress-strain diagram of a metal is independent of the section size (Fig. I). No exceptions from this rule are known. However, if the deformation of a metal is continued until rupture occurs, and the breaking stress or the work consumed is measured, a test bar of large cross section appears to fail before or at lower stresses than does one having a small cross section. Thus, the specific impact energy has been often found to decrease with increasing size of the test specimen, particularly for materials with a limited ductility.4 Another exception from the rule of similarity is offered by fatigue-strength values, which usually decrease with increasing section size.6'6 The conclusion must be drawn from these experimental facts that the ductility of a homogeneous metal decreases with increasing section size (Fig. I). This effect has been actually confirmed by Docherty,7 who observed that in static notch bending tests large specimens failed earlier and in a more brittle fashion than small specimens ma-

Jan 1, 1941

By George Sachs

I deeply appreciate the honor of being selected to deliver the twentieth Annual Lecture of the Institute of Metals Division. The subject of my paper is extremely involved and voluminous, therefore I shall discuss only some more recent experimental material and speculate somewhat on the physical and mechanical fundamentals of these changes. The flow and the rupture of a solid material are rather different phenomena. It is therefore surprising that up to a rather advanced stage in metallurgical science these two fundamental phenomena have been simultaneously treated and forced into the general conception of the "failure " of solid material. Only in this century, and particularly during the last 20 years, have the very different physical meanings of flow and rupture been clearly recognized. Several hundred of the more recent publications deal with these subjects.l Law of Similarity The basic values commonly considered responsible for the mechanical behavior of any material are the stresses. From this standpoint both a large and a small article made from the same homogeneous metal and of geometrically similar shapes should behave identically, i.e., they should deform geometrically in a similar manner, if subjected to the same stress values at corresponding points. This "law of similarity" was introduced about 60 years ago simul- taneously by Barba2 and Kick3 and was derived from the classical theory of elasticity. As far as the plastic behavior of a metal is concerned, this rule appears to be valid. The conventional properties of large and small tension or compression test bars, machined from larger sections, are identical; while the force required to deform a section is proportional to its cross-sectional area and the work consumed in deforming geometrically similar articles in a geometrically similar manner is proportional to its volume. The general trend of the stress-strain diagram of a metal is independent of the section size (Fig. I). No exceptions from this rule are known. However, if the deformation of a metal is continued until rupture occurs, and the breaking stress or the work consumed is measured, a test bar of large cross section appears to fail before or at lower stresses than does one having a small cross section. Thus, the specific impact energy has been often found to decrease with increasing size of the test specimen, particularly for materials with a limited ductility.4 Another exception from the rule of similarity is offered by fatigue-strength values, which usually decrease with increasing section size.6'6 The conclusion must be drawn from these experimental facts that the ductility of a homogeneous metal decreases with increasing section size (Fig. I). This effect has been actually confirmed by Docherty,7 who observed that in static notch bending tests large specimens failed earlier and in a more brittle fashion than small specimens ma-

Jan 1, 1941

By George Sachs

I deeply appreciate the honor of being selected to deliver the twentieth Annual Lecture of the Institute of Metals Division. The subject of my paper is extremely involved and voluminous, therefore I shall discuss only some more recent experimental material and speculate somewhat on the physical and mechanical fundamentals of these changes. The flow and the rupture of a solid material are rather different phenomena. It is therefore surprising that up to a rather advanced stage in metallurgical science these two fundamental phenomena have been simultaneously treated and forced into the general conception of the "failure" of solid material. Only in this century, and particularly during the last 20 years, have the very different physical meanings of flow and rupture been clearly recognized. Several hundred of the more recent publications deal with these subjects.1 LAW OF SIMILARITY The basic values commonly considered responsible for the mechanical behavior of any material are the stresses. From this standpoint both a large and a small article made from the same homogeneous metal and of geometrically similar shapes should behave identically, i.e., they should deform geometrically in a similar manner, if subjected to the same stress values at corresponding points. This "law of similarity" was introduced about 60 years ago simultaneously by Barba2 and Kick3 and was derived from the classical theory of elasticity. As far as the plastic behavior of a metal is concerned, this rule appears to be valid. The conventional properties of large and small tension or compression test bars, machined from larger sections, are identical; while the force required to deform a section is proportional to its cross-sectional area and the work consumed in deforming geometrically similar articles in a geometrically similar manner is proportional to its volume. The general trend of the stress-strain diagram of a metal is independent of the section size (Fig. I). No exceptions from this rule are known. However, if the deformation of a metal is continued until rupture occurs, and the breaking stress or the work consumed is measured, a test bar of large cross section appears to fail before or at lower stresses than does one having a small cross section. Thus, the specific impact energy has been often found to decrease with increasing size of the test specimen, particularly for materials with a limited ductility.4 Another exception from the rule of similarity is offered by fatigue-strength values, which usually decrease with increasing section size. 5,6 The conclusion must be drawn from these experimental facts that the ductility of a homogeneous metal decreases with increas¬ing section size (Fig. x). This effect has been actually confirmed by Docherty,7 who observed that in static notch bending tests large specimens failed earlier and in a more brittle fashion than small specimens ma-

Jan 1, 1941

By Robert L. Gower, John H. Cash

Interconnections for integrated circuits operating at rnicrowaue frequencies rzust be formed as microwave transmission lines. This paper describes the fabrication of one type of microwave transmission line known as microstrip, which can be fabricated on momlithic integvated circuits by deposition of 0.1- to 2.0-mil-thick metal and dielectric films. A microstrip line consists of a narrow conducting strip separated from a gvound plane by a dielectric material. Thick films of good conducting materials are required for low loss at high frequencies. Vacuum-evaporation methods for depositing aluminum and silver films are described. The narrow conducting strip forming the top conductor is defined by photoresist-etching techniques after the thick rnetal film is deposited. Gold plating with a photoresist-masking technique is also used to forrrz thick metal conductors. The microstrip dielectric layer is formed by deposition of suitable dielectric films 0.1 to 2.0 mils thick. Several deposition techniques were investigated. Electron-beam evaporation of quartz is described. Electrical characteristics of deposited microstrip lines at microwave frequencies are included and the microwave power attenuation as a function of conductor and dielectric thickness is given. It is concluded that the deposition of microstrip transmission lines is a practical way to achieve low-loss interconnections in monolithic integrated circuits. CONNECTIONS between devices in low-frequency and digital circuits are usually made by connecting the devices with a length of conductor such as a metal lead oi- a wire. If this method were applied to microwave integrated circuits, the reactance of the connection due to the series inductance and parasitic capacitance would be very high, in fact too high to permit successful circuit operation. In addition, resonance and antenna effects would occur at high frequencies, especially when the connections approach the wavelength.' Connections which are sections of transmis- sion line will overcome these difficulties. The electromagnetic field is confined to the volume of the transmission line, parasitic effects are not present, and circuit design utilizes familiar transmission-line techniques. TRANSMISSION LINES One type of transmission line geometrically adaptable to integrated circuits is known as micrstri. A microstrip line can be generated from a coaxial line as shown in Fig. l(a). The outer conductor of the coaxial line is distorted into an ellipse (b) and finally separated at the extremities of the ellipse to form the strip transmission line shown in (c). One of the ground planes is then removed, leaving a conducting ground plane and a narrow conducting strip separated by a dielectric. Two configurations of the microstrip line were considered in this investigation, Fig. 2. Type (a) is fabricated from a semiconductor slice with the ground plane and top conductor deposited on each side of the slice. The semiconductor slice serves as the die lec-

Jan 1, 1967

By Raymond B. Ladoo

Abrasives include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean or otherwise remove solid material, usually by rubbing action but also by impact (sandblasting, for example). They do not include abrasive tools-for instance, lathe tools and files-or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted although some chemical-action polishes and cleaners may also contain solid abrasives; for example, many automobile and metal polishes. General Considerations The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded grain abrasives such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cutting edges when grains become worn-for example, in garnet for sandpaper, neither highly cleavable or friable grains nor extremely tough grains are wanted. For still other uses, great hardness is objectionable; for example, abrasives for dentifrices and for glass-cleaning soaps. For the most efficient use in the more critical applications, the different types of abrasives are rarely completely interchangeable; thus, while crushed quartz and garnet are both used in sandpaper, the papers are not at all interchangeable in their use applications. In the last analysis, the choice of a high-grade abrasive depends upon the quality and quantity of work done by the abrasive per unit of cost. Initial cost of an artificial abrasive. may be much greater than that of a natural abrasive but the artificial abrasive may do so much better work than the natural one, and do it so much faster, that the ultimate cost will be less. It is on this basis that artificial abrasives have largely replaced natural abrasives for grinding metal. Classification Abrasives may be divided into two general classes, natural and manufactured. The former includes all rocks and minerals used for abrasive purposes without chemical or physical change other than crushing, shaping or bonding into suitable forms. Manufactured or artificial abrasives are made either by heat or chemical action from metals or mineral raw materials. On page 2 is a list of the most important abrasives, classified as to inherent types and as to forms in which they are used industrially. For most types of use there are manufactured products that can be substituted for the natural products, usually at higher initial

Jan 1, 1960

By H. M. Kraner, R. C. Devries, K. H. Gee, E. F. Osborn

On the basis of liquidus measurements in the system COO-Mg0-Al2O3-Sio, and previously published data, diagrams have been constructed at 5 pct Al2O3, intervals from 5 to 35 pct Al2O3,. Liquidus temperatures and primary phase fields are shown. The optimum composition of a blast furnace slag for a given alumina content is indicated. At the optimum point, ordinary slags will be entirely liquid and will have maximum desulphurization potential and minimum viscosity. The relation of optimum composition of slags to the "plateau region" of the liquidus surface, and the application of these data on synthetic quaternary slags to actual slag compositions are discussed. Index of refraction of glasses is given as well as composition, temperature, and phase data for each mixture. THE usual blast furnace slag, as a first approximation, can be considered a mixture of the four oxides, CaO, MgO, Also,, and SiO,. Systematic, extensive data for the quaternary system, CaO-MgO-A1,0,-SiO, is therefore required for the understanding of the properties of such a slag as a function of composition and temperature. With sufficient data, it should be possible to fix unequivocably the relative amounts of lime, magnesia, and silica required for a given alumina content to result in a slag composition having optimum properties. Other constituents, such as FeO, MnO, Ti02, and S, have an effect on the properties of a slag, but as long as they are present in small and approximately constant amounts they produce only a second-order effect superimposed upon the major changes in properties of slags determined by the relative amounts of the four major components. Viscosity and desulphurization data have been reported for mixtures approaching blast furnace slags in composition, but systematic liquidus data have not been obtained. Inasmuch as a slag must be all liquid in order to be most effective as well as practicable, clearly the temperature above which a mixture is all liquid (liquidus temperature) is a type of data needed. Such data have been obtained through the study of 446 compositions and are pre- sented in this paper along with a discussion of their bearing on the optimum composition of blast furnace slags. For an orderly presentation of the data, the quaternary system is viewed as a tetrahedron with one component at each apex. Fig. 1 shows a tetrahedron representing the system Ca0-Mg0-A1,0,-Si0,. The base is the ternary system Ca0-Mg0-SiO,, A1,0, is the top apex, and the front face, the system CaO-

Jan 1, 1955