Search Documents

By G. W. Tracy, R. D. Carter

A method based on an approach by Hurst' is developed for calculating water influx behavior. Using this method, superposition calculations may be eliminated. The principal diflerence between this method and that of Hurst is that, over finite intervals of time, constant oil-productton rates are assumed by Hurst whereas constant water influx rates are assumed in the presently described method. By adopting the assumption of constant water influx rate for finite time periods, a method is developed for calculating water influx behavior which lends itself to convenient combination with the material balance equation in the Schilthuis form. Above the bubble point, an equation is given for the explicit step-wise calculation of pressure history for a prescribed oil-production history. Use of this method of calculating water influx behavior should result in a considerable saving of time as compared to superposition calculations when the calculations must be made without using a digital computer. The connection is shown between the method described herein and the method developed by van Ever-dingen and Hursr2 (which requires superposition cal-culations). Also, results obtained using the two methods are compared.

By Mrs. V. J. DeCarlo, G. P. Salvo, H. W. Schadler, L. M. Osika

The lattice parameter of the inlerrnetallic compound Nb3Sn has been measured as a function of temperature from 80° to 1290°K. The results are compared with published data on the thermal ex- ThE recent interest in the intermetallic compound, Nb3Sn, as an engineering material for the production of superconducting devices has necessitated that certain engineering data be obtained. Because of the difficulty encountered in producing bulk pansion of niobium and indicate that the compound when made by diffusion of tin into niobium at 1000°C, would be subjected to a tensile strain of about 0.1 pct when cooled to room temperature. material which is single phase, the coefficient of thermal expansion has not been measured by dilata-tional methods. Therefore the lattice parameters of fine-grained samples of Nb3Sn produced on the surface of a niobium sheet by heating in molten tin at 950°C have been obtained as a function of temperature. The results are compared with published data on niobium2 and Nb3Sn3 and with lattice-parameter measurements made on small single crystals of Nb3Sn.

Jan 1, 1964

CHARLES SCHUCHERT,* New Haven, Conn. (written discussion?).- I embrace ace the opportunity to take part in a discussion of Mr. Woodruff's paper because a successful discerning of what actually constitutes pet-roliferous areas from the geologists' standpoint is worthy of our endeavors, not only from the intellectual side, but also because it may lead, as Mr. Woodruff hopes, to the more certain establishment of principles that can be applied to other continents in exploiting them for petroleum. This discussion will also embrace the results of two other recent papers, one by Alexander W. McCoy and one by Maurice G. Mehl.1 Sources of Petroleum.-Mr. Woodruff is agreed that petroleum comes from plants and animals, or possibly from both, and that it has ac-cumulated by migration into reservoir rocks. These reservoir rocks must of course be porous to become catch basins for the oil and gas, and then, too, their present structures are variable, as they occur in anticlines, domes, terraces, etc. , The structures, he states, are more widespread than are the oil pools, and the same is true for the reservoir rocks. Accordingly, there must be many good sands and structures

Jan 11, 1919

By Lyman H. Hart

Some of the significant facts that will affect the supply and demand for metals during the next few decades are given in this presentation. This is important because the only hope for intelligent guidance of the national destiny depends upon presenting a consistent and accurate picture of basic problems. The metals problems now fomenting are only slightly less important than those precipitating the energy crisis. Admittedly, it is difficult to generate serious thinking on this subject when the world is enjoying easy access to all metals at modest prices. This is possible because of the current world capacity to overproduce, and United States credit standing, at least up to now, has permitted buying freely on world markets. Although both these vital conditions are subject to change, there is little doubt that if the U.S. financial house is kept in order, we can muddle along for a while on a generally expanding, metalbased economy. But should our credit standing be permitted to collapse, or should there be a tightening of world supplies of metals, the nation would immediately find itself in trouble. Unfortunately, clear signals indicate that both of these conditions are threatening.

Jan 4, 1973

By N. J. King, R. F. Hadley

Alluvial valley floors constitute a valuable land resource and are important to ranching operations in the semiarid western United States. This resource may be in jeopardy locally if the alluvial deposits are disturbed by surface mining of coal deposits. Erosion problems caused by poor land-use practices can cause trenching of the unconsolidated alluvium with a consequent lowering of the water table and depletion of soil moisture needed to support vegetation. Historical evidence of this sequence of events is abundant in the geologic literature and serves as the basis for assessing potential impacts of surface mining. The potential geomorphic impacts of surface mining on alluvial valley floors with regard to fluvial processes are. (1) disruption of the longitudinal profile followed by valley trenching and high sediment yields downstream, and (2) replacement of the excavated alluvium with unconsolidated material that does not have similar physical characteristics and may be susceptible to erosion. Mining may disrupt the existing hydrologic framework affecting stream flow, ground-water levels, and water quality of both surface and ground water. Although functional hydrologic and geomorphic processes are similar, each valley represents a complex environment that does not submit to broad generalizations.

Jan 1, 1981

By R. A. Foos

During the radium boom in the early part of the twentieth century, the basic chemistry of uranium was fairly well defined. Uranium production has progressed from the status of a radium by-product to a very important industry. With the ever increasing need for more efficient and cheaper methods of processing uranium ores, new techniques are being developed. Since uranium and vanadium often occur together in nature, the latter element will also be considered. As production rates, costs, and certain aspects of uranium chemistry are still classified by the Atomic Energy Commission, these will not be discussed. Domestic uranium deposits, in general, are composed of the minerals carnotite, which contains hexavalent uranium, and to a lesser extent, pitchblende and uraninite, which contain tetravalent uranium. Carnotite also usually contains vanadium. The uranium and vanadium contents of these ores vary considerably. The ores currently processed on the Colorado Plateau assay from 0.2 to 0.4 pct U and from trace amounts to 5.0 pct V. On the other hand, the phosphate rock deposits of the southeastern U. S., from which uranium is also recovered, contain only about 0.01 to 0.02 pct; processing of the

Sep 1, 1956

BOSTON SECTION ALFRED C. LANE, Chairman, GEORGE A. PACKARD, Vice-chairman, E. E. BUGBEE, Sec'y-Treas., Mass. Inst. of Technology, Cambridge, Mass. R. L. AGASSIZ, FRED W. DENTON. Forty-sixth Meeting The forty-sixth meeting of the Boston section was held at the University Club on Monday evening, Jan. 28, 1918. Thirty-six members and guests were present, which is a record for this Section. After a good dinner, President Philip N. Moore, of the Institute, was introduced, and spoke of the many problems of the Institute. The topics covered were the progress and growth of the Institute during the administrative year, the efforts to stimulate the local sections and to bring them more in touch with the policies and problems of the parent body and, last but not least, of the constructive results and patriotic work of the Institute in the national service of the war. The other guest of the Section, Mr. Thomas Nelson Perkins, Counsel for the Priority Board, spoke most entertainingly of recent experiences in Russia, England and France. After considerable discussion during which Mr. Perkins most obligingly answered innumerable questions, the meeting adjourned at about 10 p. m.

Jan 7, 1918

By Georges Ranque

THIS paper by. Georges Ranque is an attempt to reason out the conditions of formation and stability of inclusions and to establish an operative process capable of eliminating or minimizing them. The paper consists of two parts; one in which the author considers the laws of physical chemistry and physics that apply to liquid slag-metal systems and one in which he describes a practice based on the theoretical considerations. Such a paper is bound to contain controversial points and it is therefore your speaker's intention to present Mr. Ranque's side of the picture to the best of his ability without regard for any thoughts or criticisms of his own. RISING VELOCITIES OF INCLUSIONS Most nonmetallic inclusions have densities ranging from about 1.7 to s, while liquid steel has a density of about 7. Under these conditions, ferrostatic pressure should cause the inclusions, being lighter, to rise from the bath and be eliminated. This rising tendency is expressed by Stokes' law, from which may be calculated the rising velocity of a spherical particle in a liquid medium whose density and viscosity are known.

Jan 1, 1947

By C. G. Black

THE purpose of this paper is to present data obtained from an investi-gation conducted on the grindability of coal by the American Society for Testing Materials Tentative Standard ball-mill method. This investiga-tion has been conducted over a period of a year, during which time several hundred tests were run on a wide selection of different coals coming from Pennsylvania, Ohio, West Virginia and Kentucky. The data herewith presented tend to show that the tentative standard ball-mill method might give results that are misleading and that a volume measure might be more indicative of the true grindability 'of materials of varying specific gravity. A means whereby the time element might be reduced has been studied and other phases of this work such as preparation of samples, mechanical screening, reporting results and duplicating tests have been investigated. It is hoped that all criticism offered in this paper will be taken as constructive, with the purpose in mind of perfecting the method now tentative to show the true conditions and of making optional the manner in which certain parts of the test might be conducted to meet diversified laboratory conditions.

Jan 1, 1936

By Alan Probert

IN his inaugural address in 1949, President Truman made a policy declaration which launched the foreign technical assistance program known to the world as Point Four. Congress passed Public Law 535 defining the scope of the program and holding activities to certain limitations. It also provided $34.5 million for the first fiscal year. The Technical Cooperation Administration was established within the Department of State to coordinate and direct a program to include "economic, engineering, medical, educational, agricultural, fishery, mineral and fiscal surveys, demonstration, training and similar projects." The mineral programs of Point Four have been staffed and managed by two agencies of the Department of Interior, the Geological Survey and the Bureau of Mines. The Geological Survey is concerned primarily with water-supply problems, the discovery of mineral deposits, and the determination of habit, shape, and grade of mineral deposits. The Bureau of Mines is concerned with determining the commercial potentialities of mineral deposits, mineral technology, and the production and distribution of mineral commodities. Mineral projects comprised only 1 pet of the first year's budget. In spite of the relatively insignificant expenditure compared to those for food, agriculture, and health, a commendable record has been achieved.

Jan 1, 1952

By G. E. Agar, A. L. Mular

G. E. Agar (Manager, Minerals Processing Research, International Minerals & Chemical Corp., Skokie, III.) — The author notes a discrepancy between the parameters a and ß which are the slopes of the size distribution and energy-size modulus plots respectively. The reason for the discrepancy and the systematic decrease in the magnitude of a with grinding time is abundantly clear from the work of Fuerstenau8 on dry grinding. Fuerstenau shows very clearly in his Fig. 5 that at short retention times the parameter a is the same as that obtained by sizing over the complete size range. From this figure, it is obvious that sizing to only 400 mesh gave distribution curves similar to Mular's - that is, the slope apparently decreased systematically with increased grinding. As a consequence of the improper determination of a, the magnitude of ß given by Mular must be larger than the true value. In order to demonstrate this, the following Fig. 6 was taken from Mular's paper (his Fig. 1). Fuer-stenau's results show that we can approximate the correct value of K by drawing lines parallel to the short retention time curves through the 400-mesh

Jan 1, 1963

By K. C. Li

TITANIUM, because of its high strength, weight ratio, and high melting point, became the metal of the jet age. Zirconium, because of its low neutron cross section and high corrosion resistance to hot water, became an integral part of the nuclear era. Since both metals are very similar chemically, more or less the same process is used for their production. The sudden rise of this new industry of titanium and zirconium seems to have caused some uncertainty as to the future development of processes for making these metals. Although zirconium was discovered in 1789 and titanium in 1790, it was not until 1945, six years after W. J. Kroll patented his process, that F, S. Wartman of the U. S. Bureau of Mines perfected the technique of producing ductile titanium, and it was not until 1946 that Kroll perfected the technique of producing ductile zirconium in commercial quantities. Since then the Government and private industry have spent millions of dollars each year constantly searching for new methods, with the hope that some day titanium can be produced as economically as aluminum and magnesium or as cheaply as stainless steel.

Jan 11, 1957

By G. St. J. Perrott

During the past year, the Bureau of Mines has carried on an investigation of liquid-oxygen explosives (L.O.X.) to supplement the work described in previous publications.' The present paper gives results of the first part of this work, which was a laboratory investigation of the properties of typical combustibles used in L.O.X., and the relation of these properties to the absorption and retention of oxygen by the explosives and their explosive characteristics. No attempt will be made to describe the development of liquid-oxygen explosives, because this phase of the subject has been well covered.2 The L.O.X. cartridge consists of a paper wrapper filled with an absorbent combustible material that is saturated with liquid oxygen by soaking it therein. After saturation, the cartridge is removed from the liquid and fired with fuse and cap, or electric detonator, in a manner similar to other explosives. Certain types of cartridge may be detonated with fuse alone, requiring no cap to initiate the detonation. ' By suitable variation of the nature and density of the combustible, cartridges having a wide variety of explosive characteristics may be made.

Jan 1, 1925

By Eduardo J. Chibas

Location.—The principal manganese-deposits of the Department of Panama, Republic of Colombia, are located almost clue south of Viento Frio, a native village bordering on the Caribbean Sea, and about 45 miles northeast of Colon (Aspinwall). The mining-claims are the Viento Frio, the Carrano, the Nispero, and the Soledad. Each property is to the south of the preceding one in the order mentioned. The first one is about one mile from the coast, and the most southerly boundary of the Soledad is about five miles in a straight line from the same coast-line. I shall confine my remarks to the four properties mentioned and to La Guaca, west of the Carrano, because these are the only ones where mining has so far been done to more or less extent. Manganese has also been found, however, in the neighborhood of these deposits, and a large area adjoining them has been divided into sections and " denounced " as mining-claims. The relative position of the manganese-deposits and Nombre de Dios, the present terminal of the railroad and shipping-port, as well as Viento Frio and the adjacent coast, can

Jan 1, 1898

By J. Koskinen, P. Vanninen, T. Leskinen, A. Leppala

Continuous and accurate analysis of slurries has become a critical requirement in mineral processing. With on-stream assay data, automation procedures can be employed to obtain higher recovery and improved control of production. The Courier system was developed by Outokumpu Oy, taking advantage of mineral processing know-how, to provide means for achieving these objectives in the company's ore concentrator operations. It became evident, based on early experience with on-stream analysis, that the Courier should be a complete system to fulfill all functions of the analysis operation. The system includes equipment and techniques for primary sampling, sample preparation for assaying, and processing of data for final assay results. In addition, the on-line X-ray spectrometer unit was developed specifically for industrial use, incorporating a number of technical advances. A new system for converting spectrometric data to assays is based on a physical model programmed on a digital computer. The Courier system is furnished on a turn-key installation basis incorporating all elements needed for operation including calibration. The experience to date with the Courier system at the Pyhäsalmi concentrator is summarized. Reference is also made to recent results with installations at the Outokumpu and Vihanti concentrators.

Jan 1, 1972

THE 127th meeting of the Institute was held in New York, Feb. 19 to 22, 1923. In addition to the usual large volume of technical matters under consideration, the meeting was particularly noteworthy for the amount of attention given to its business session; the convention of local section representatives also was full of interest. The total registration was 1201. The annual business meeting on Feb. 20, President Dwight presiding, was attended by 125 members, who listened with marked attention to the reports and addresses of the several officers. The chairman departed from the stipulated order of business in order to allow more time for the presentation of remarks on the state of Institute affairs. The previously pub-lished reports of the officers were accepted, as printed. On the report of the tellers, the following officers were declared elected: E. P. Mathewson, Director and President-District 0 T. T. Brewster, Director and Vice-president-District 6 Frank M. Smith, Director and Vice-president-District 11 W. H. Aldridge, Director-District 0 G. H. Clevenger, Director-District 1 A. N. Diehl, Director-District 3 Reno H. Sales, Director-District 7 Seeley W. Mudd, Director-District 10

Jan 3, 1923

By Jack Parker

There are some simple theoretical approaches to pillar design but they leave much to be desired. There are also more complex theoretical approaches, but at this time the most realistic approach is to go into the mines and observe and measure how real pillars are performing under real conditions; to allow the information thus gathered to ferment in our minds - then to project the behaviour of those pillars into our new designs and mining techniques, probably with no formulas at all. Examples, from half-a-dozen different mines, show how a simple- minded approach, through observation and measurement, led to changes in pillar design which often contradicted the textbook but made very significant contributions to mining safety, efficiency and costs. The good news is that we know a lot more about pillar design than we realize. We have, between us, looked at millions of pillars of all kinds, under all conditions, but we have overlooked what they are trying to tell us. We can take problem situations and turn them into opportunities and, in that way, become better stewards of the resources which have been given to us.

Jan 1, 1983

By F. H. Rhines, A. H. Grobe

The constitution of the indium-zinc alloy series has been investigated by Wilson and Peretti,1 who determined the liquidus and eutectic temperatures by the conven-tional method of cooling curves and the eutectic composition by analyzing eutectic exudations. Recent developments affecting the availability of indium and consequent increased interest in its applications make a more complete knowledge of the constitu- tion of its alloys desirable. As a part of a program far the reexamination of the constitution of indium alloys by precision methods, the indium-zinc phase diagram (Figs. I and 2) has been redetermined in its entirety. The eutectic temperature (I43. 5°C.) reported by Wilson and Peretti has been confirmed exactly, but their value of the zinc concentration at the eutectic, 4 per cent, was found to be high; the new value is 2.8 per cent of zinc. There is also a rather large difference between the forms of the liquidus curves of Wilson and Peretti and those found in the present studies. The solidus curves herein have been located for the first time and the limits of solid solubility have been tenta-

Jan 1, 1944

By A. H. Grobe, F. H. Rhines

The constitution of the indium-zinc alloy series has been investigated by Wilson and Peretti,1 who determined the liquidus and eutectic temperatures by the conven-tional method of cooling curves and the eutectic composition by analyzing eutectic exudations. Recent developments affecting the availability of indium and consequent increased interest in its applications make a more complete knowledge of the constitu- tion of its alloys desirable. As a part of a program far the reexamination of the constitution of indium alloys by precision methods, the indium-zinc phase diagram (Figs. I and 2) has been redetermined in its entirety. The eutectic temperature (I43. 5°C.) reported by Wilson and Peretti has been confirmed exactly, but their value of the zinc concentration at the eutectic, 4 per cent, was found to be high; the new value is 2.8 per cent of zinc. There is also a rather large difference between the forms of the liquidus curves of Wilson and Peretti and those found in the present studies. The solidus curves herein have been located for the first time and the limits of solid solubility have been tenta-

Jan 1, 1944

By L. B. McConville

The general term "tar sand" refers to sand that contains varying amounts of dense, viscous petroleum. Tar sand deposits have been found throughout the world, often in the same geographical area as conventional petroleum. The largest one by far is known as the Athabasca Tar Sands, in the province of Alberta, Canada. Actually a group of three deposits, these particular sands underlie an aggregate area of more than 12,000 sq miles. Current estimates place the contained raw petroleum at about 700 billion bbl; and via currently available technology, the amount of recoverable synthetic oil may be as much as 300 billion bbl-which is roughly equivalent to five times the combined US and Canadian total crude oil reserves. With the ever-widening gap between energy supply and demand, mining and petroleum companies are now evaluating all possible energy resources-both developed and underdeveloped-and, certainly, the Athabasca Tar Sand deposit is one of the more important ones to merit such attention. The first section in ME deals with the geology and historical developments; the other four sections, with mining methods, extraction technology, economics, and outlook.

Jan 1, 1975