Search Documents

By Richard D. Hagni

Although the ore microscopist routinely examines polished sections to determine the mineralogy and texture of ores, his importance to the solution of problems peripheral to geology is not always fully realized. The techniques which he uses can be applied with little modification to the solution of a wide variety of beneficiation problem. By extending his studies beyond those normally considered to be of interest to the geologist, he can include examinations of polished sections of selected mill products. This is a logical extension, because the minerals and textures in the polished sections of ores are the same as those in millproducts. The mill dressing engineer should be more aware of the types of beneficiation problem that can be solved by the ore microscopist and what the ore microscopist can do for him. A greater degree of cooperation between the ore microscopist and the mill dressing engineer can be of significant mutual benefit. Ore microscopy holds an advantage over chemical analysis, because the interrelations and combinations ofthe mineral constituents of an ore or mill product can be visually determined. This advantage provides solutions to many beneficiation problem. Locking is a type of beneficiation problem that is particularly amenable to ore microscopy. The percentage, type, and distribution of locked particles can be readily determined with the aid of an ore microscope and an estimate made of the extent of additional grinding required for liberation. The extent of intimately locked types, which no reasonable amount of grinding will liberate, can also be evaluated. Mineral coating conditions, free particles of a deleterious mineral, and free particles of a valuable mineral held in flocculated clusters of gangue are other features that can readily be observed. In some instances, visual examination may show that the problem is not one of locking. Photomicrographs illustrate the variety of beneficiation problems for which the ore microscope is applicable. These problems and their resolution demonstrate the importance of the instrument and show the value of close coordination between the mill dressing engineer and the ore microscopist.

Jan 1, 1979

By O. W. Shimer, D. C. Helms, C. E. Brown

THE early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 334 million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20° to 90° and some are on the invert in, many sharp folds and faults. PLANNING The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been maintained. Locations of stripping areas are determined as follows: 1. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness and pitch of the beds.

Jan 1, 1944

By Gary A. Kordosky

Winning copper from oxide ores usually involves hydrometallurgical techniques. The processes involved are the leaching of copper from the ore and the recovery of the leached copper from the aqueous solution.

Jan 1, 1981

By L. H. Van Vlack, T. Y. Tien, R. J. Martin

The phase relationships of the MnTe-MnS system were studied by DTA procedures. There is an eutectic at 810°C with about 10 mole pct MnS-90 mole pct MnTe. An eutectoid occurs at about 710°C with approximately 7 mole pct MnS where the MnTe(NaCl) solid solution dissociates on cooling to MnTe(NiAs) and MnS. There is very little solid solubility of MnTe in MnS. ALTHOUGH MnS may exist in three different crystal forms,' only the NaC1-type phase is stable.2 Above 1040°C, MnTe also has the cubic NaC1-type structure. Below that temperature, MnTe changes to the NiAs-type structure.3 This phase transition is rapid for both heating and cooling. As a result the high-temperature crystal form of MnTe cannot be retained at room temperature. Because MnO, MnS, and MnSe are all stable with the NaC1-type structure, and MnTe has this structure at high temperatures,4 solid solution formation could be expected among these compounds. It is interesting to note, however, that a complete series of solid solutions exist only in the MnS-MnSe system,' and that the solid solution is quite limited in the MnO-MnS system.' The MnSe-MnTe system possesses a complete series of solid solutions at high temperatures with separation at lower temperatures.7 Although ion size may be critical in the miscibility of MnO-MnS, it is quite possible that the bond type plays a more important role with the miscibility of MnSe-MnTe. This would permit us to speculate that the miscibility gap would be extensive in the MnTe-MnS system. EXPERIMENTAL Preparation. The samples were prepared by mixing and compacting MnTe and MnS powders. The MnS was previously prepared through the sulfur reduction of Mnso4.8 The MnTe had been prepared by mixing and compacting double vacuum distilled metallic manganese and high-purity tellurium in stoichiometric ratio modified with 1 wt pct excess tellurium. The compacted powders were put in a graphite crucible which was sealed in an evacuated vycor tube. The free space in the vycor tube was made minimal to reduce the loss of tellurium. The sealed assembly was then heated slowly to about 500° C where the free manganese and tellurium reacted vigorously, melting the MnTe which formed. Only one phase, MnTe, was detected by X-ray powder patterns and metallographic techniques. Each compact of MnTe-MnS was placed in a graphite crucible and then sealed in an evacuated vycor tube. The samples were heated at 1250°C for 4 hr and furnace-cooled. Microscopic examination revealed no third phase beyond MnS and MnTe. A typical microstructure is presented in Fig. 1. Identification. X-ray powder patterns were obtained using 114.6 mm Debye-Scherrer camera and Fe-Ka radiation. Mixtures of cubic MnS and hexagonal MnTe were observed in all of the compositions prepared. No lattice parameter change was noticed among different compositions, indicating no solid solution could be retained at room temperatures between these two end-members. A lattice parameter of 5.244Å for MnS was obtained by the Nelson and Riley9 extrapolation method using the diffraction lines of (h2 + k2 + 12) equal 12, 16, 20, and 24. The values, a = 4.145Å and c = 6.708Å, for hexagonal MnTe were obtained from the (006) and (220) lines in the back-reflection region. These values agree well with the values reported by Taylor and Kag1e.10 Differential Thermal Analysis. A differential thermal analysis procedure was used to determine phase relationships since the high-temperature equilibrium conditions could not be retained for examination at room temperature, even when the sealed samples (~0.5 g) were quenched in water. The samples were sealed in an evacuated 4 mm vycor tube with a recess in the bottom to accept a thermocouple. An Al2O3 reference was similarly prepared and the two placed within a piece of insulating fire brick to dampen spurious temperature changes within the furnace. The furnace was controlled by a mechanically driven rheostat which increased the temperature at a rate of about 15°C per min. Known phase changes in the Pb-Sn system1' and the a-to-ß quartz inversion12 were used for calibration

Jan 1, 1969

By Rossiter W. Raymond

(Canal Zone Meeting, November, 1910.) THE death of Professor Blake removes the oldest of American economic geologists and mining engineers, and deprives this Institute of one of its, earliest and most illustrious members. To many of us it brings a personal loss also, the loss of a friend. William Phipps Blake was born June 21, 1826, in New York City. -His father, Elihu Blake, was a surgeon-dentist of eminence, a direct descendant of William Blake, who settled in the Massachusetts Bay Colony about 1630. He was prepared for college at private schools in New York, and entered the Sheffield School of Yale, where he was graduated as Ph.B. in the chemical course, class of 1852, the first graduating-class of the institution. In the same year he became chemist and mineralogist of the New Jersey Zinc Co., and chemist of chemical works at Baltimore, Md. In 1853, lie started the Department of Mineralogy of the World's Fair at New York City. In 1854, 1855 and 1856, he was mineralogist and geologist of the United States Pacific Railroad Surveys of Williamson, Pope, and Whipple, and for the War Department at Washington. His writings, during this period comprise reports on the geology and mineralogy of California and other parts of the Southwest, and constitute well nigh the earliest scientific accounts of the regions described. One of them. was a translation of the Resume and Field Notes of Jules Marcou, of Whipple's expedition. From 1856 to 1859, he was engaged in explorations of the geology and mineral deposits of North Carolina, :and other parts of the country. In 1859, he became editor and proprietor of The Mining Magazine. This was a monthly periodical, founded in 1853 by W. J. Tenny, who conducted it until 1858, when it passed into the hands of Thomas McElrath, a New York publisher, and appeared in May of that year as The Mining and Statistic Magazine, with the name of

Sep 1, 1910

By H. I. Aaronson

Isothermally formed plates of proeutectoid a, lengthen at approximately the rates predicted by the Zener-Hillert equation, indicating that their lengthening kinetics are controlled by the volume diffusion of chromium in the ß matrix. Solution annealing treatments in the vicinity of the transus introduce a second mode of transformation, in which the lengthening rate is at least 1.8 x 104 faster than predicted by this equation. Little or no volume diffusion appears to accompany the latter transformation. The Presence of oxygen is evidently a Prerequisite for the occurrence of this reaction. X HE effects of thermal history prior to the initiation of transformations which proceed by nucleation and diffusional growth are currently evoking considerable interest. The rate of nucleation (but not the rates of growth) of pearlitel and of bainite,2 and the over-all rates of aging reactions in Al-cu3 and Al-si4 alloys have been shown to be appreciably dependent upon thermal history in the solid-solution region"' or in the two-phase region prior to the onset of pre~ipitation.3,4 In none of these reactions, however, was the transformation mechanism changed by variations in the temperature-time path used to reach the reaction temperature. Preliminary experiments reported by M. K. McQuillan5,8 and a systematic investigation by Farrar and Margolin7 have disclosed that the transformation behavior of hypoeutectoid Ti-Cr alloys is considerably more sensitive to thermal history. Qualitative evidence strongly suggests that not only the rate of nucleation but also the rate of growth and even the mechanism of the ß — a reaction can undergo remarkable changes when a solution annealing treatment in the vicinity of the ß/a +ß, or transus temperature, is interposed between a high-temperature solution anneal (conventionallq at 1000°C) and the isothermal reaction treatment. The present investigation was undertaken in an attempt to ascertain the nature and origin of these effects. Study of the changes in the kinetics and morphology of the ß - a, reaction produced by varialtions in thermal history was the primary means employed for this purpose. EXPERIMENTAL PROCEDURE The compositions of the alloys used in this in~esti~ation are given in Table I. These alloys were homogenized for 5 days at 1050° C in evacuated (2 x 10 -5 mm of Hg), zirconium-gettered fused quartz capsules. The capsules themselves were enclosed in a porcelain chamber evacuated with a mechanical pump during the homogenization anneals. Upon completion of homogenization, the alloys were cooled to room temperature and then reheated to 550°C for 3 1/2 days in order to transform the alloys to a finely divided mixture of a and TiCr2, and thus provide an approximately constant initial mi-crostructure. Individual specimens were sealed in evacuated and internally gettered Vycor capsules and heat treated as previously described.8,9 EXPERIMENTAL RESULTS Ti-10.64 Pet Cr. This investigation was largely performed on the 0.64 pet Cr alloy. The "base"

Jan 1, 1962

By O. W. Shimer, D. C. Helms, C. E. Brown

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944

By J. B. Clark

The oil industry has long recognized the need for increasing well productivity. To meet this need, a process is being developed whereby the producing formation permeability is increased by hydraulically fracturing the formation. The "Hydrafrac" process, as it is now being used, consists of two steps: (1) injecting a viscous liquid containing a granular material, such as sand for a propping agent, under high hydraulic pressure to fracture the formation; (2) causing the viscous liquid to change from a high to a low viscosity so that it may be readily displaced from the formation. To date the process has been used in 32 jobs on 23 wells in 7 fields, resulting in a sustained increase in production in 11 wells. INTRODUCTION Need For Process Although explosives, acidizing, and other methods have long been used, there still exists a need for artificial means of improving the productive ability of oil and gas wells, particularly for wells which produce from formations which do not react readily with acids. This paper discusses the development of a hydraulic fracturing process, "Hydrafrac", which shows distinct promise of increasing production rates from wells producing from any type of formation. The method is also considered applicable to gas and water injection wells, wells used for solution mining of salts and, with some modification, to water wells and sulphur wells. Requirements of Process In considering such a possible process, it appeared that certain requirements must be met. Some of these are as follows: A. The hydraulic fluid selected must be sufficiently viscous that it can be injected into the well at pressure high enough to cause fracturing. B. The hydraulic fluid should carry in suspension a propping agent, such as sand, so that once a fracture is formed, it will be prevented from closing off and the fracture created will remain to serve as a flow channel for oil and gas. C. The fluid should be an oily one rather than a water-base fluid, because the latter would be harmful to many formations. D. After the fracture is made, it is essential that the fracturing fluid be thin enough to flow hack out of the well and not stay in place and plug the crack which it has formed. E. Sufficient pump capacity must be available to inject the fluid faster than it will leak away into the porous rock formation. F. In many instances, formation packers must be used to confine the fracture to the desired level, and to obtain the advantages of multiple fracturing. Development of Process As a necessary step in the development of this process, it was deemed advisable to determine if the Hydrafrac fluids were actually fracturing the formation or whether these special fluids were merely leaking away into the surrounding formation. To determine this, a shallow well, 15 feet deep, was drilled into a hard sandstone. Casing was set, the plug drilled, and the well deepened in the conventional manner. A fracturing fluid dyed a bright red was used to break down the formation. Sand mixed with distinctively colored solids was injected into the well with the fracturing fluid to prop open any fracture made in the formation. A simulated gel breaker solution dyed a bright blue was then pumped into the well to determine if the gel breaker would follow the first solution. The results are shown in Figure 1. It was noted that a fracture was formed about the well bore, that the propping agent was transported back into the break, and that the breaker solution did actually follow the fracturing gel out into the fracture. While it is realized that this shallow well test is probably not exactly equivalent to a deep test, the results were interpreted as being a definite indication of what happens down the hole during a Hydrafrac job. Of interest in this connection is an investigation reported by S. T. Yuster and J. C. Calhoun, Jr.' This study, re~orted after the Hydrafrac work was under way, presents some excellent field data supporting the theory of fracturing a formation with hydraulic pressure. METHOD Steps of Hydrafrcu: Process Figure 2 shows a simplified cross-sectional view of a well treated by one version of the process. The first step, formation breakdown, is done with a viscous fluid, usually consisting of an oil such as crude oil or gasoline, to which has been added a bodying agent. Due to availability and price, war-surplus Napalm has been used in the majority of experiments to date. Napalm is the soap which was used in the war to make "jellied gasoline". The next step consists of breaking down the viscosity of the gel by injecting a gel-breaker solution and then after several hours, putting the well back on production. Figure 3 shows diagram-matically, a typical field hookup. The oil or gasoline is unloaded into the 10 bbl. tank shown on the left rear of the truck. This base fluid is picked up by the mixing pump and pumped through the jet mixer, where the granular soap is added. Next it goes into a small mixing tub, from which the high-pressure pump takes suction. The solution is then pumped into the well. The breaker solution is then taken from an extra tank and is displaced into the well immediately following the gel. When required, additional trucks may

Jan 1, 1949

By J. B. Clark

The oil industry has long recognized the need for increasing well productivity. To meet this need, a process is being developed whereby the producing formation permeability is increased by hydraulically fracturing the formation. The "Hydrafrac" process, as it is now being used, consists of two steps: (1) injecting a viscous liquid containing a granular material, such as sand for a propping agent, under high hydraulic pressure to fracture the formation; (2) causing the viscous liquid to change from a high to a low viscosity so that it may be readily displaced from the formation. To date the process has been used in 32 jobs on 23 wells in 7 fields, resulting in a sustained increase in production in 11 wells. INTRODUCTION Need For Process Although explosives, acidizing, and other methods have long been used, there still exists a need for artificial means of improving the productive ability of oil and gas wells, particularly for wells which produce from formations which do not react readily with acids. This paper discusses the development of a hydraulic fracturing process, "Hydrafrac", which shows distinct promise of increasing production rates from wells producing from any type of formation. The method is also considered applicable to gas and water injection wells, wells used for solution mining of salts and, with some modification, to water wells and sulphur wells. Requirements of Process In considering such a possible process, it appeared that certain requirements must be met. Some of these are as follows: A. The hydraulic fluid selected must be sufficiently viscous that it can be injected into the well at pressure high enough to cause fracturing. B. The hydraulic fluid should carry in suspension a propping agent, such as sand, so that once a fracture is formed, it will be prevented from closing off and the fracture created will remain to serve as a flow channel for oil and gas. C. The fluid should be an oily one rather than a water-base fluid, because the latter would be harmful to many formations. D. After the fracture is made, it is essential that the fracturing fluid be thin enough to flow hack out of the well and not stay in place and plug the crack which it has formed. E. Sufficient pump capacity must be available to inject the fluid faster than it will leak away into the porous rock formation. F. In many instances, formation packers must be used to confine the fracture to the desired level, and to obtain the advantages of multiple fracturing. Development of Process As a necessary step in the development of this process, it was deemed advisable to determine if the Hydrafrac fluids were actually fracturing the formation or whether these special fluids were merely leaking away into the surrounding formation. To determine this, a shallow well, 15 feet deep, was drilled into a hard sandstone. Casing was set, the plug drilled, and the well deepened in the conventional manner. A fracturing fluid dyed a bright red was used to break down the formation. Sand mixed with distinctively colored solids was injected into the well with the fracturing fluid to prop open any fracture made in the formation. A simulated gel breaker solution dyed a bright blue was then pumped into the well to determine if the gel breaker would follow the first solution. The results are shown in Figure 1. It was noted that a fracture was formed about the well bore, that the propping agent was transported back into the break, and that the breaker solution did actually follow the fracturing gel out into the fracture. While it is realized that this shallow well test is probably not exactly equivalent to a deep test, the results were interpreted as being a definite indication of what happens down the hole during a Hydrafrac job. Of interest in this connection is an investigation reported by S. T. Yuster and J. C. Calhoun, Jr.' This study, re~orted after the Hydrafrac work was under way, presents some excellent field data supporting the theory of fracturing a formation with hydraulic pressure. METHOD Steps of Hydrafrcu: Process Figure 2 shows a simplified cross-sectional view of a well treated by one version of the process. The first step, formation breakdown, is done with a viscous fluid, usually consisting of an oil such as crude oil or gasoline, to which has been added a bodying agent. Due to availability and price, war-surplus Napalm has been used in the majority of experiments to date. Napalm is the soap which was used in the war to make "jellied gasoline". The next step consists of breaking down the viscosity of the gel by injecting a gel-breaker solution and then after several hours, putting the well back on production. Figure 3 shows diagram-matically, a typical field hookup. The oil or gasoline is unloaded into the 10 bbl. tank shown on the left rear of the truck. This base fluid is picked up by the mixing pump and pumped through the jet mixer, where the granular soap is added. Next it goes into a small mixing tub, from which the high-pressure pump takes suction. The solution is then pumped into the well. The breaker solution is then taken from an extra tank and is displaced into the well immediately following the gel. When required, additional trucks may

Jan 1, 1949

By O. W. Shimer, D. C. Helms, C. E. Brown

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90° and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness and pitch of the beds.

Jan 1, 1946

By John Birkinbine

Secretary's Note.—In printing this paper in the present volume, the figures given in the pamphlet edition have been brought more nearly up to date, the product of 1899 being in many instances inserted. Iron-Ore Resources. In a paper presented to the Institute in 1897,* I discussed the iron-resources of the United States as then developed, calling attention to some principal sources upon which other countries depended. The following statement will give a general idea of the amounts, as compiled from the latest official records, of ores won, and metal produced, in the nations which are important contributors to the world's output. Unfortunately these are not all contemporaneous, since in some countries the statistics do not appear until after one or more years. The statement covers not only pig-iron and iron-ore, but also manganese-ore —the manganese mined being principally used in the production of spiegeleisen or ferro-manganese, and these alloys being generally included in the pig-iron output. Table I, which epitomizes the present situation, shows respectively the countries and the quantities of iron-ore and man-

Jan 1, 1901

By C. H. Li, R. J. Stokes, T. L. Johnston

The phenomenon of solid-solution strengthening has previously been studied in a number of binary alloy systems.1-8 There has been, however, very little information published concerning the strengthening effects of specific solutes in magnesium alloys. Schmid and his coworkers9,10 investigated the behavior of aluminum and zinc in binary and ternary magnesium-alloy single crystals, but this work was done before high-purity materials were readily available. Workers at the Dow Chemical companyH reported increases in the critical resolved shear stress upon alloying magnesium single crystals with zinc and indium. Recently, Hardie and parkins* investigated the extent of hardening produced by the addition of various solutes to poly crystalline magnesium. The present work was undertaken to provide data on the strengthening effects of a number of solutes in high-purity magnesium, for the purpose of supplying further experimental information which might be useful in describing a general mechanism for solid-solution strengthening. To simplify interpretation of the results, the mode of deformation was limited to basal slip, through the use of single crystals. EXPERIMENTAL PROCEDURE Magnesium and magnesium binary-alloy single crystals containing indium, cadmium, thallium, aluminum, and zinc were prepared in the form of l/2-in.-diam rods, approximately 8 in. long, using a modified Bridgman technique in which the crystals were slowly cooled from the melt in a steep temperature gradient, in an atmosphere of helium. It was found that a solid-liquid interface travel speed of about 0.7 in. per hr consistently produced single crystals. The poly crystalline starting materials for the preparation of single crystals consisted of 1/2-in.-diam extruded rods, prealloyed to the desired composition. The unalloyed magnesium and magnesium-indium extrusions were furnished by the Dow Chemical Co. The other alloys were prepared at the Rensselaer Polytechnic Institute Metallurgical Laboratories. Some preliminary studies of the strengthening effect of indium were conducted at room temperature using a constant rate of tensile loading of 1040 g per min. Stress was applied to the crystals by means of a simple 5:l lever arm. The lever was loaded by a constant rate of flow of shot into a receptacle suspended from the long arm of the lever. Plastic flow was detected by an electrical resistance strain gage cemented to the surface of the crystal normal to the minor axis of the predicted glide ellipse. The crystals were acid machined to produce tensile specimens with a reduced section between the grip ends, with an additional step in the center of the reduced section to compensate approximately for the slip-retarding effect of the strain gage. The balance of the single crystals were extended in an Instron tensile tester. This machine employs a synchronously driven screw and automatically records applied load as a function of cross-head separation. It became unnecessary therefore, to employ a strain gage to detect deformation or to acid machine a reduced section. Preparation for testing reduced merely to chemical cleaning of the surface, thus minimizing the amount of handling and probability of accidental damage to the crystals. The rate of elongation employed in all the tests was 0.002 in. per min, corresponding to a strain rate of approximately 0.0004 per min. EXPERIMENTAL RESULTS The investigation confirmed the finding of many workers that the yield strength of hexagonal metal crystals is strongly orientation-dependent. This is illustrated in Fig. 1, in which o, the tensile stress required to produce gross plastic flow in eleven unalloyed magnesium crystals stressed at a constant rate of loading is plotted as a function of sin X, cos Ao where X, is the angle between the

Jan 1, 1960

By Paul M. Tyler, Colin G. Fink

THE field of rare metals is so broad that progress can be reported upon many important fronts. Not satisfied with the 92 elements that Mendeleeff and his followers have accepted as legitimate, scientists are trying now to complicate matters by making new elements. Enrico Fermi announced the fabrication of "Element 93". Uranium, instead of being allowed to disintegrate slowly according to its normal habit, was bombarded with neutrons until some of them seemed to have stuck in the nucleus. To understand just what is alleged to have happened all one has to do is to line up the elements in their usual order of ascending atomic weight and imagine, as physicists do, that each atom is a little solar orbit comprising a central mass or planet about which other masses revolve like satellites. Ordinary hydrogen, being very light, consists of only one positively charged proton center, with only one positively charged electron revolving about it. Other atones are progressively more complicated until we come to uranium, which has a relatively big center and 92 particles revolving around it.

Jan 1, 1935

By A. B. Parsons

AT the outset, the authors of this paper desire to file a disclaimer and an, explanation. They have no inside information from occult sources; neither of them feigns clairvoyant powers in the slightest degree. It is true that they have indicated on be graphs an approximate trend for the consumption of seven important mineral commodities up to the year 1954. At best this is a risky business; the figures do not pretend to be any- thing more than reasoned conjectures that are predicated on an attempt to evaluate some of the more obvious of the many factors that are likely to have a bearing on the future.

Jan 1, 1937

By AIME AIME

AMONG the European nations Germany is the center of interest economically as well as politically, and of prime importance for Europe as a whole is Germany's capacity to produce mineral products for armament and for export in exchange for the import of the essential supplies to maintain its industries. So far as minerals are concerned, Germany is worse off than any other great power except Italy, and deficiencies are being met by attempts to increase output from local deposits and by greater use of substitutes derived from domestic raw materials to replace imported metals, petroleum products, and other minerals.

Jan 1, 1939

By Arthur La Motte

I NDUSTRIAL explosives, as distinguished from military explosives, include high explosives and blasting powder. The high explosives which are best known are straight dynamite, gelatin dynamite, ammonia dynamite and permissibles. There are two kinds of blasting powder, saltpetre blasting powder and nitrate of soda blasting powder. Blasting powders are mechanical mixtures of nitrate of potash or nitrate of soda with sulfur and charcoal, highly compressed, granulated and glazed. They ignite from a spark and burn with relative slowness, the rate of burning and hence the rate of conversion into gases depending upon the size of the granulation and upon the degree of. confinement under which the powder is placed. High explosives, on the other hand, are chemical compounds which detonate; that is, when the explosive is subjected to a violent shock, provided in practice by a blasting cap or an electric blasting cap, the molecule of the essential ingredient, usually nitroglycerin, is disrupted and the energy and heat released cause any other explosive ingredients which may be present, such as ammoniuin nitrate or T.N.T., to decompose with a resultant evolution of gases at an extremely rapid rate varying from 6000 to 20,000 ft. per second.

Jan 1, 1924

By P. Somasundaran, D. R. Nagaraj

This study initiated to explore the potential of commercial chelating extractant for beneficiation of minerals revealed "LIX "65N to be an excellent collector for cuprite and chrysocolla. The collector action of the LIX is proposed to result from its chelation with copper species on the surface of the minerals. Thus, the syn-isomer of LIX65N, which is unable to form a chelate with copper ions, failed also to act as a collector. The proposed mechanism takes into account partitioning of LIX between the mineral surface (to form a surface chelate) and the copper chelate dispersed in the bulk aqueous phase (either due to formation of the chelate with dissolved copper, or due to detachment of chelate formed at surface). The efficiency of the collection is dependent upon this partitioning since the bulk chelate is found unable to collect. The marked decrease in flotation obtained when copper was added to the system supports this mechanism. The dependence of flotation of chrysocolla and cuprite on pH and reagentizing time is discussed on the basis of the proposed mechanism. Batch laboratory flotation tests using synthetic mixtures of oxide, sulfide and mixed oxide-sulfide copper minerals with quartz demonstrated the ability of LIX to separate the copper minerals from quartz.

Jan 1, 1980

By J. P. G. Farr, R. Brownsword

THE role of solute segregation in the formation of cellular solidification substructures in tin and its dilute alloys is well-established, see, e.g., Ref. 1. Segregation has been shown to persist during cooling, enabling solidification structures to be studied from sections taken at some distance behind the interface. In the present work, a single crystal of commercial nickel, 99.965 pct, was examined in this way. The crystal was cut from the center of a rod given a single pass in an electron beam floating zone melter. Polished sections of a nickel specimen taken normal to the growth direction showed a very fine precipitate phase, the distribution of which varied over the section. The identification of the phase proved difficult because of the small amount present and the small particle size, about 1 p: but it was shown by probe microanalysis to contain only nickel and oxygen in detectable concentrations and was probably nickel oxide, NiO. Bulk analysis of the material before melting showed there to be only 3 to 4 ppm of oxygen present, thus demonstrating a very considerable segregation concentration effect. In some areas of the section the precipitate formed a discontinuous hexagonal network suggesting decoration of the cellular boundaries known to be present in the sample2 whereas in a restricted region the precipitate formed small clusters. Occasionally it could be seen that the clusters were at the intersections of an hexagonal network of cellular dimension. It was suggested3 that this was the result of enhanced segregation to the cell boundary intersections whereas general cell boundary segregation was insufficient to give a precipitate. Enhanced nodal segregation has since been demonstrated in a number of systems.1, 4-8 The development of a suitable electrolytic etching technique (perchloric acid 20 pct v/v; ethyl alcohol 70 pct; glycerol 10 pct; current below electropolishing plateau; 1 to 2 sec etching) suggested the association of the phase with regions of solute segregation (where ko < 1); in these regions anodic attack produced grooves or depressions. In a study of the variation of solidification substructures with degree of constitutional supercooling, Biloni et a1.&apos; appear to have used standard growth conditions and varied the solute concentration. They were able to produce in a series of individual tin crystals examples of substructure ranging from planar interface through various cellular structures to den- Fig. 1—Electroetched section taken normal to the rod axis; the center of the rod lies to the left and the periphery to the right of the micrograph. The variation of structure across the section is evident. Magnification 60 times. drites. It was possible in the present nickel crystal to observe a continuous range of substructures varying with degree of supercooling across a single section as shown in Fig. 1. Growth rate, 13 mm per min, and temperature gradient were essentially constant; the variation in structure is thought to be due to a radial gradient in solute concentration ahead of the solid interface. The liquid at the interface is likely to have been richer in solute toward the periphery of the zone, the result of curvature of this interface. The type of substructure was seen to vary with increasing constitutional supercooling as follows: a) region free of precipitate. top left, Fig. 1: 6) region of nodal precipitates which became arranged in hexagons on passing from the center of the rod: c) irregular hexagonal cells with incomplete boundary precipitation; d) regular hexagonal cells of decreasing size with complete boundary precipitation. Fig. 2 shows the transition from stage 6 and Fig. 3 shows the structure in stage d. Within stage 0, the range of conditions over which irregularly positioned nodes occur appears to be small and the nodes are soon recognizable as taking up positions at the intersections of an hexagonal network as the supercooling increases.

Jan 1, 1970

By C. H. Bushell, M. Malnarich

REAGENT control in flotation is more an art than a science. Operators vary the amount of reagents used according to the metallurgy obtained. The amount of collector may be increased, for example, if tailings losses are high and decreased if concentrate grades are low. Often control decisions are based on only one assay, such as the tailings analysis by microscopic or quick assaying techniques. This method of control has given reasonably satisfactory results but is clearly far from perfect. No adjustment in reagent addition can be made until information is received that metallurgy has deteriorated, that is, until the optimum time for adjustment has already passed. The first adjustment probably will be an overcorrection or an undercor-rection, and time will be required to establish the best new addition rates. The seriousness of the problem depends on variability of the ore. In ore of continually shifting composition and complexity, mill results will shift back and forth from excessively high concentrate grades and high tailings losses to excessively low concentrate grades and low tailings losses. Economic incentive for improved control also increases with increasing size of mill. Even a small improvement in percentage recovery in a large mill pays for expensive control equipment. The Sullivan concentrator of The Consolidated Mining & Smelting Co. of Canada Ltd. at Kimberley, B. C., treats 11,000 tpd of complex lead-zinc ore, a scale of operations which justifies an extensive research program on automatic control. Work has followed two separate lines: 1) development of faster analytical methods for pulps, and 2) study of metallurgical control by measurement and control of reagent concentrations in flotation solutions. Although work is incomplete in both phases, a progress report can be given on the development of reagent control. The primary requirement in flotation is selective attachment of particles of one mineral to air bubbles while the other minerals remain detached. Hydrophobicity of mineral surfaces is established by the collector, which coats the minerals by adsorption. The requirement of selective affinity for air bubbles is therefore equivalent to requiring selective adsorption of a collector. Adsorption theory, supported by abundant experimental evidence, shows that the amount of a reagent adsorbed at a surface must be a function of its residual concentration in solution. As the concentration in solution rises, the amount adsorbed increases, usually following some type of logarithmic curve. Selective adsorption must depend on a natural difference in the minerals, but ordinarily the differences in affinity are not great enough to obtain complete coverage of one mineral while the others are completely uncoated. An optimum concentration will exist, below which coverage will not be great enough to float enough of the valuable mineral, and above which too much unwanted mineral will float. All other reagents, except some frothers, affect the amount of collector adsorbing at constant residual collector concentration in solution, either by adsorbing competitively with the collector, or by a

Jan 1, 1957

By C. A. Wert

THE change in mechanical properties accompanying quench aging of carbon in a iron has been known for a number of years. Since the amount of carbon involved is rather small, however, no measurements could be made to correlate the property change with the state of precipitation of the carbide. Indeed, until a few years ago it was not plain which property might be used to indicate the state of the progress of precipitation. Some years ago the internal friction of solid solutions of carbon in a iron was demonstrated, and the use of this phenomenon to ascertain the amount of carbon in solid solution at any given time was developed. Shortly afterward the author made a number of measurements in which changes in electrical resistance, thermoelectric emf, and hardness were determined simultaneously with the internal friction (and hence with the precipitation) ? A little later Dijkstra and Wert measured the change in magnetic coercive force accompanying aging.&apos; The present work was undertaken to inquire into the changes in yield strength accompanying aging. The work was done on specimens made of Puron. These specimens were 0.05 in. in diam and about 6 in. long. Though specimens of this small size are not ideal for yield strength measurements, such specimens are desirable for internal friction meas-

Jan 1, 1952