Search Documents

By W. F. Baldwin

The timing circuit generally employed in Carter Reservoir Behavior Analyzers consists of a synchronous motor driven cam which actuates a microswitch. A mechanically actuated timer of this type has several inherent disadvantages, among which are the following: 1. The first time interval may not be of uniform length, depending on the exact position of the cam at the conclusion of a previous run. 2. The positioning adjustments on the microswitch lever arms are critical and require periodic readjustment. 3. The mechanical system is subject to wear which will ultimately impair its accuracy. It was therefore considered desirable to devise an alternate method which would eliminate these difficulties without introducing others that would be equally troublesome. This note describes the design of an electronic timing device which has been incorporated in the analyzer constructed by the Field Research Laboratories of Magnolia Petroleum Co. The electronic timer circuit is built around a simple neon glow tube relaxation oscillator, the complete circuit diagram of which is shown in Fig. l. The operation of the circuit is as follows: Condenser C, is charged to the critical firing voltage of the neon glow tube VR-75 by battery B1 through resistors R1 and R2. When the neon glow tube fires, the condenser C, is discharged, The charging cycle then repeats itself,

Jan 1, 1950

By Thomas M. Plouf

Flotation, as we know it today, is a physiochemical method of concentrating finely ground ores. The process involves chemical treatment of an ore pulp to create conditions favorable for the attachment of certain mineral particles to air bubbles which are carried to the surface of the ore pulp for removal. Frother reagents, combined with air and the agitation mechanism, produce the effective bubbles in a flotation cell. A method of analysis is presented to evaluate the effect of frother reductions and additions on a bank of flotation cells, and to economically determine if and to what extent frother reductions and additions are justified. Comparative evaluations of different frother systems, as well as the amount of frother used in a given flotation machine, cannot be made on the frother cost alone. An indepth study must be made to evaluate any given frother as applied to a particular ore body. The recovery of a given mineral is as dependent on the amount of frother as on the type of frother used. An actual case study follows in which the amount of frother required by two different flotation machines was used to make a decision as to which unit performed more efficiently based on costs. This same method may be used to evaluate new frothers as well as to determine if a larger frother addition is advisable.

Jan 11, 1975

In a letter to the Secretary, Sir Robert A. Hadfield encloses a statement of the terms and conditions under which his prize is to be awarded by the Institution of Mechanical Engineers, and also a table comparing the hardness of a large variety of steels, examined both by Brinell and by scleroscope methods, together with the tensile and compressive strength of the same specimens. The conditions for the award of the prize are as follows: SIR ROBERT HADFIELD PRIZE For a new Method of Determining the Hardness of Metals 1. Sir Robert A. Hadfield, D. Sc., D. Met., F. R. S., Vice-President, has placed in the hands of the Institution of Mechanical Engineers the suns of £200, which, with any income therefrom, may he awarded at the discretion of the Council of the Institution as a prize or as prizes, for the description of a new and accurate method of determining the hardness of metals, especially of metals of a high degree of hardness. 2. The ordinary tests of hardness, such as are described in the report of the Hard-ness Tests Research Committee (Proceedings of the Institution of Mechanical Engi=neers, 1916, pages 677 to 778), which should he consulted by competitors, fail to some extent when the hardness of the material exceeds about 600 to 800 Brinell. What is

Jan 3, 1918

By Alvin F. Kroll

BUNKER Hill & Sullivan Mining & Concentrating Co. has three major sources of ore at present: high grade square-set ore, low grade caving ore, and low grade reclaimed washed jig tailing. These three ores constitute the feed to the 3000-tpd concentrator that produces lead-silver, zinc, and pyrite concentrates. Each ore has different characteristics of grindability, mineral particle size, composition, and content, but all are amenable to the same mill circuit and reagents. The gangue is primarily quartzite. The Bunker Hill concentrator is now using a coarse primary grind followed by a regrind of sand fractions of lead rougher tailing, lead middling, and lead cleaner tailing, and further regrind of sand fractions of zinc middling and zinc cleaner tailing. This is done in order to recover all valuable minerals at the largest size possible. The tendency to overgrind the ore particles, which are more easily ground than the gangue particles, is thereby reduced-lessening their loss in the flotation tailings. The coarse primary grind and regrind method has the advantages of: providing more selective grinding, minimizing sliming, giving a cleaner lead-zinc separation, and reducing mill requirements for reagents and water. Improved lead-zinc separation raises overall recovery and also increases lead and zinc recovery in the respective concentrates by keeping middling particles out of concentrate and tailing.

Jan 6, 1954

By A. Lee Barrett

THE Maintenance Committee of the Coal Division of the American Institute of Mining and Metallurgical Engineers is presenting with this report the first of a series of cost comparisons which it plans to present to the Institute. The plan is to assemble maintenance cost on all equipment connected with mechanical operations at the face of coal mines, to arrange these costs by districts, to make comparisons between districts, and within districts. This particular report covers data with respect to mobile loading machines, including both "on-track" and "off-track" equipment. It is anticipated- in-fact, considerable data have already been accumulated-that next year complete maintenance costs by districts can be presented for complete loading units, including the various classes and combinations of on-track and off-track equipment. Data have also been collected with respect to some phases of maintenance methods and certain recommendations of the committee are included dealing with maintenance problems. In the assembly of these data more than 120 questionnaires were sent to operating companies through- out the United States. At the time the report was written 33 questionnaires had been returned with completed information and an additional group of companies had written that the information requested was not at present available but that they hoped to have such information available in the not far distant future. The replies as

Jan 1, 1946

By R. R. Van Valkenburch

IT has always seemed to me that mining methods are inventions that follow necessity. I have yet, to be connected with a property where the consultant who has been engaged has laid out a mining method that has been strictly adhered to through the life of the mine. Possibly there are exceptions. As a general rule, perhaps, the method becomes the result of sad experience. I suppose if a person were to attempt to measure the tendency to get away from shrinkage stoping, he would need to send out a questionnaire and expect to receive truthful answers, and, having compiled the results, I think we would find that throughout the country there would be but few cases where present value of product permits the old original so-called shrinkage method to be followed. The method that I had hoped to hear Mr. Fozard expound is strictly an adaptation of shrinkage. Cav-ings do not enter. It was developed by Mr. Fozard and his staff at the Beatson mine of the Kennecott Copper Corp., at, Latouche, Alaska. Stephen Birch, in the TRANSACTIONS in 1923, submitted a brief paper on the mining at Beatson. He stated that a new adaptation of shrinkage was being tried because, although at sur-face the copper .content had been relatively high, at lower levels, in the mine it had decreased.

Jan 5, 1927

The high-grade orebody at Miami was mined successively by top-slicing, shrinkage, stoping and under caving. The method described in this paper was developed to enable the low-grade orebody (36,000,000 tons assaying 1.06 per cent copper) to be mined at a low cost without further dilution of the grade. The method is clearly described and illustrated by drawings and photographs, and the original paper should be consulted as it is impracticable to abstract it, beyond noting that the mining cost is just under 40 cents per ton and the average grade of ore now being produced yields less copper than the mill tailing of 1915, the tons mined per day having increased from 4000 to 18,000 in the same period. Vertical and Incline Shaft Sinking at North Star Mine By Arthur B. Foote, Grass Valley, Calif. (Tech. Pub. No. 324: Class A. Metal Mining, No. 36) THE main shaft of the North Star mine is an inclined one following the main vein at an average dip of 26 deg., a vertical shaft intersects it at the 4000-ft. (incline) level, the incline continuing to the 6300-ft. level. At this point the vein was found to give out and a new vein, called the No. 1, was found to dip in exactly the opposite direction.

Jan 1, 1930

By Robert Greenwood

The advent of the space age and its promise of interplanetary flight has prompted new ideas for propulsion systems that will allow maximum energy with minimum fuel weight. The use of cesium as the source of energy for such rocket flights has been found desirable. Theoretical efficiency of a rocket fuel is measured in terms of specific impulse, defined as the number of pounds of thrust per pound of propellant consumed per second. Specific impulse is usually expressed in seconds (the number of seconds for which one pound of fuel would produce one pound of thrust) although it is really a measure of total energy, not of power. The most sophisticated chemical fuels have a specific impulse of 300 to 400 sec; liquid hydrogen heated by nuclear reactor has a specific impulse of 1000 to 1200 sec. Specific impulses as high as 20,000 sec, however, are theoretically attainable with the ion rocket, in which free cesium ions are accelerated across a voltage drop and ejected at high velocity.' Characteristics of the system have been sketched by Boden. The desirable properties of an ion propellant are: 1) low ionization potential, 2) low boiling point, and 3) high atomic weight. Alkali metals best fulfill these requirements, and Table I indicates the superiority of cesium. The use of heavy complex ions such as UCl; is ruled out by their instability and other disadvantages.

Jan 5, 1960

FOLLOWING- the major explosion disaster in the Orient No. 2 mine of the Chicago, Wilmington and Franklin Coal Co., West Frankfort, Ill., on December 21, 1951, resulting in the death of 119 miners, an investigation was made by the U. S. Bureau of Mines under the direction of J. J. Forbes, Bureau director. The subsequent report concluded that the disaster. was caused by the emergence of a-large body of explosive gas from an abandoned area and simultaneous short circuiting of the ventilating current; the gas was ignited by an electric arc from nonpermissible electrical equipment and the flame was propagated throughout a large part of the affected area by coal dust and possibly by gas from other worked-out and abandoned areas. An immediate repercussion of the disaster was the opening of hearings by the. Senate Labor and Public Welfare Subcommittee on the Neely Mine Inspection Bill (S. 1310, introduced April 11, 1951) which would give federal coal-mine inspectors power to enforce safety recommendations by ordering the withdrawal of all employees where conditions constitute an imminent danger to their safety. Two days of testimony, January 24 and 25, disclosed that coal operators were not in agreement on the bill, although John L. Lewis, speaking for the UMWA, and J. J. Forbes, for the Bureau of Mines, were advocates.

Jan 1, 1952

By Robert L. Grayson, Y. J. Wang, R. Mike Mishra

Prediction of ventilation needs in long range mining projections requires serious consideration when formulating those projections. Predicting the behavior of the ventilation system of an old, complex mine poses an especially provocative problem. Air-flow around and through mined-out areas via bleeder systems, leakage flows through stoppings or other air control devices, and the use of multiple fans all add to the basic complexity of a ventilation system and make predictions of ventilation changes very difficult. Fortunately, the task of making ventilation decisions can be greatly assisted by ventilation surveying and computer simulation. The Nemacolin Mine of Jones and Laughlin Steel Corporation, located in Southwestern Pennsylvania, is one such old mine which used the computerized approach successfully. A mine-wide pressure-quantity survey was used to obtain realistic values for airway resistance factors. These values, together with network topology, formed the basic input for computer simulation. Results from this simulation indicated that air quantities generated at critical airways by the model were generally within a couple of percent of those measured in the actual survey. It was then concluded that the model was acceptable for practical application, and it was used immediately for studying the effects on the ventilation system of changing the blade settings of fans. Additionally, the model was modified to incorporate projected mine development and used to predict future ventilation.

Jan 1, 1982

By John Dasher

Extrapolation is a useful technique, but it can be overdone. Seldom is it justified to study over a range of 1 to 6 and extrapolate the results to 150,000. It is especially dangerous if the extrapolation is based on a false assumption. The authors assume settlers scale-up by residence time rather than by area, admit their result (a settler depth of 7 m) is "unreasonable" and suggest longer, wider, shallower settlers might be better. Various authors have noted for a copper-LIX system a total flow basis of 2 gpm per sq ft for sizing settlers. The results of this are compared with those in the paper in [Table 7]. The authors note that flooding of their settlers was never approached. Thus the smallest unit calculated is understandably twice too big. The largest however, is 5% of the required size. I note that the figures in [Table 6] for 1/min/cm2 are based on plan area rather than cross section as titled and are wrong by l0 4. A flow of 2050 1/min/cm2 is about Mach I. It is also 10 5/3 or 46.5 times that of the little one, although the abstract says the design was based on constant flow rate per unit cross section.

Jan 1, 1977

By A. Lee Barrett

The Maintenance Committee of the Coal Division of the American Institute of Mining and Metallurgical Engineers is presenting with this report the first of a series of cost comparisons which it plans to present the Institute. The plan is to assemble maintenance cost on all equipment connected with mechanical operations at the face of coal mines, to arrange these costs by districts, to make comparisons between districts, and within districts. This particular report covers data with respect to mobile loading machines, including both "on-track" and "off-track" equipment. It is anticipated—in fact, considerable data have already been accumulated—that next year complete maintenance costs by districts can he presented for complete loading units, including the various classes and combinations of on-track and off-track equipment. Data have also been collected with respect to some phases of maintenance methods and certain recommendations of the committee are included dealing with maintenance problems. In the assembly of these data more than 120 questionnaires were sent to operating companies throughout the United States. At the time the report was written 33 questionnaires had been returned with completed information and an additional group of companies had written that the information requested was not at present available but that they hoped to have such information available in the not far distant future. The replies as

Jan 1, 1947

By A. Lee Barrett

The Maintenance Committee of the Coal Division of the American Institute of Mining and Metallurgical Engineers is presenting with this report the first of a series of cost comparisons which it plans to present the Institute. The plan is to assemble maintenance cost on all equipment connected with mechanical operations at the face of coal mines, to arrange these costs by districts, to make comparisons between districts, and within districts. This particular report covers data with respect to mobile loading machines, including both "on-track" and "off-track" equipment. It is anticipated—in fact, considerable data have already been accumulated—that next year complete maintenance costs by districts can he presented for complete loading units, including the various classes and combinations of on-track and off-track equipment. Data have also been collected with respect to some phases of maintenance methods and certain recommendations of the committee are included dealing with maintenance problems. In the assembly of these data more than 120 questionnaires were sent to operating companies throughout the United States. At the time the report was written 33 questionnaires had been returned with completed information and an additional group of companies had written that the information requested was not at present available but that they hoped to have such information available in the not far distant future. The replies as

Jan 1, 1947

By Robert A. Rapp

The standard molar free energy of formation of MOO,was determined between 750o to 1050o C in galvanic cell measurements involving the solid electrolyte Zr0.85 Ca0.15 O1.85. Use of the reference electrodes Fe + FexO and Ni + NiO Provided two independent determinations of FoMoo2. The data may be represented by the equation FMoO2 = -137,500 +40.0T(°K) which is in good agreement with previous CO/CO, gas equilibrium measurements of Gleiser and Chipman. The standard molar free energy of formation of molybdenum dioxide has recently been reported over a large range of high temperatures from the calorimetric experiments of King, Weller, and christensen.' Gleiser and chipman2 have also recently determined ?FmoO2 from 926o to 1068oC in CO/CO2 gas equilibrium measurements. Earlier gas equilibrium studies have been made and reviewed by Gokcen.' Over the temperature range studied by Gleiser and Chipman their values for ?FoMoO2 differed from the calorimetric data by about 700 cal. This investigation was undertaken to resolve this difference and thereby establish the two phase mixture of Mo + MOO, as an electrode of well-known oxygen potential for galvanic cell applications at very high temperatures. The galvanic cell technique involving the Zr,.,, Ca,0.15 01.85 solid electrolyte was introduced for the

Jan 1, 1963

By James W. Neill

The occurrence of minerals of nickel and cobalt at Mine La Motte is probably known to every mineralogist. I will not attempt to describe these minerals, but, before entering on my subject, will briefly mention the ores, etc., which call for metallurgical treatment and enter into the composition of our mattes. Our staple lead-ore, the dressed galena, is the chief source of nickel and cobalt. It carries but a small percentage of these metals, viz.: 0.2 to 0.3 percent. usually, though when much copper pyrites is contained in the gangue, the amount of nickel and cobalt may be as great as 1.0 to 1.5 per cent. Next in importance is the ((middle product" of the dressingworks, consisting of the sulphides of iron (and copper) with gangue and galena. This usually carries 20 to 23 per cent. of lead, 0.5 to 1.0 per cent. of copper and 2.5 to 3.5 per cent. of nickel and cobalt. A larger percentage of copper always carries with it an increase of nickel and cobalt. In some few cases 12 to 15 per cent. of copper gives 6.5 to 8.0 per cent of these metals. Resides these products of the dressing-works, there is a small quantity of true nickel-cobalt-ore

Jan 1, 1885

By D. W. Hutchinson, W. W. Wen, A. A. Terchick, J. C. Anderson

It is estimated that approximately 3% of the raw coal processed today in coal preparation plants throughout the nation will ultimately report to slurry-tailing disposal (Anderson, 1975). The usual disposal method is to pump refuse slurry containing - 48 mesh (300 pm) refuse into dams or impoundments constructed of coarse refuse. The failure of an impoundment at Buffalo Creek, Saunders, WV (Anon., 1972) resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of federal regulations dealing with the construction, operation, and final abandonment of coal refuse disposal area. As a consequence of these regulations, the use of the landfill/impoundment method of disposal became in some cases economically unfeasible or technically impossible. US Steel has studied a number of alternative methods of refuse disposal. During an investigation of mechanical dewatering with a pressure filter, portland cement was added to the slurry to solidify the filter cake. Because of the success of the cement addition, it was decided to study the stabilization of fine coal refuse slurry through use of cement-type additives. The goal of the investigation is to develop a process that will use cement-type additives to solidify the refuse slurry into a form that can be handled and stacked with the coarse refuse, thus eliminating the need for slurry impoundments.

Jan 1, 1982

By Paul Hett

The much-heralded Deep Ruth operation of Kennecott Copper Corp., at Ruth, Nev., is scheduled to become a producer by 1957. Inaugurated as a project in 1951, production was originally scheduled to start in 1953, but excessive water hindered shaft sinking. A revised schedule called for output by 1955, but again plans had to be changed. This time the change was to permit mining of an orebody that would have otherwise been lost because of block caving methods planned for the main deposit. The new ore is within the cave limits of the larger orebody, above the first production level. Ore will start coming from this new source in 1956, a year ahead of the principal operation. (See NEWS, page 344.) There is little doubt that current economic conditions and unforeseen expenditures for early shaft development will make the Deep Ruth a high-cost producer. Yet, some of the drawbacks of the Kennecott operation may be mitigated by the possibility that additional exploration will increase the already assured 25 million tons of 0.83 pet copper ore. While Kennecott is missing out on the current high copper market and is thus left with a potentially narrowed profit, the predicted demand for copper has created an optimistic feeling. Its development is certain to enlarge known U. S. copper reserves and significantly extend the life of Kennecott's Nevada operations.

Jan 4, 1955

HENRY A. VEZIN, Denver, Colo. (communication to the Secretary, February, 1897): I have read Mr. Austin's paper with considerable interest, more especially as the designing and study of such works have been an attractive occupation for me during the last twenty-five years. Mr. Austin says that a " plant on a terraced site has generally been considered the most advantageous," and also that " many advocate a level site," while he himself " is disposed to advocate a modification of the latter plan, utilizing an extended surface with a moderate slope."* Among the advocates of the terraced sites as against level ones, I do not recollect ever meeting a metallurgist who had even made an attempt to plan his works for level ground, or who had, in a lucid interval, figured how much he gained or lost by one or the other method. The average metallurgist starts with the assumption that it is rational to conduct his material down hill because its movement is aided by gravity, while to elevate ore or furnace-material by machinery he vaguely believes to be not alone wrong in principle, but also unnecessarily expensive. Let us look into the expense of elevating and see whether it really is prohibitory of the successful operation of smeltingworks on a level site. Hoisting or elevating material in the

Jan 1, 1897

By R. K. Govila, E. H. Parkison

THE interplanar angles for hcp metals vary with c/a ratio, and therefore must be computed separately for each particular metal or alloy. Manual computation of these angles is laborious and time consuming, and for this reason computer programs have been developed to accomplish this task.1"3 However, these programs have certain disadvantages. For example, they require prior knowledge and understanding of ALGOL or FORTRAN languages. Further, they will not print out specific angles but instead give all angles between given limits—thus program2 prints out a total of 26,649 angles between planes with indices and in the range from (4 4 4) to (4 4 4) for any given c/a ratio. The purpose of this note is to present a simple and inexpensive computer program for accomplishing this task. This program is written in BASIC language4 which does not require any prior knowledge of computer programming, and is ideally suited for nonprofessional programmers. It also provides flexibility for the user by allowing him to select any indices for as many or few planes as desired for any given c/a ratio. The computer program proposed below is based on the relationship in which + is the angle between any two planes and . TO illustrate use of the program, consider the problem of calculating the interplanar an-

Jan 1, 1970

By Jouko O. Kallioinen

The control of zinc flotation at Outokumpu Oy's Pyhasalmi and Vihanti mines is described. At Pyhäsalmi the zinc flotation circuit is partially open. Zinc and other metal assays of pulp flows are measured and direct assay control of concentrates in various flotation steps is adopted. Assay control is carried out by adjusting flotation air and pulp levels. Optimization with copper sulphate ensures high Zn- recovery and minimum copper sulphate consumption. A froth depth monitor is used to measure froth quality. At Vihanti the zinc flotation takes place in closed circuit. The most important control loop is the Zn-assay control of rougher concentrate by adjusting flotation air. The quality of froth is measured indirectly and thus copper sulphate consumption is altered. The circulating load is controlled also by flotation air in the three cleaning steps. The comparison of the control strategies shows that a more sophisticated control is adopted at Pyhäsalmi because the selective flotation of this massive sulphide ore is considered to be difficult. The control strategy includes numerous tests performed by the computer and control algorithms developed for the case. The control targets of the two zinc flotations described are also different: At Pyhäsalmi Zn-assay control of final concentrate including copper sulphate optimizing, at Vihanti the control of circulating load and Zn-assay of rougher concentrate.

Jan 1, 1984