Search Documents

By M. S. Klima, P. T. Luckie

An evaluation of the operating performance of a recently designed pneumatic centrifugal classifier is presented. This classifier has been modified from a separate air and feed input design to an entrained solids in air feed input. The evaluation first required determining the size distributions for the three streams (feed, fine, and coarse). Using size distribution data and mass flow rates, a size selectivity curve was calculated for each operating condition tested. This curve, in turn, was characterized by appropriate selectivity parameters (i.e., the equiprobable or cut size, the sharpness index, and the apparent bypass values). The variation of these parameters with classifier operating conditions was examined. From these evaluations, the "best" operating conditions for the classifier were then determined.

Jan 1, 1985

By John H. Smith

Because of increased pressure from federal and state regulatory agencies, most acid flows will require some sort of treatment prior to being discharged to receiving streams. In many industries, the volumes of liquors are large and their acid content varied. Development of a waste treatment process minimizing equipment cost and utilizing land efficiently is mandatory. Methods of acid neutralization with lime have been known for years, however, the volume and characteristics of the resultant precipitated solids can create a disposal problem. Also, when standard lime treatment is used, the settling characteristic of the precipitated solids is normally slow. In some instances, the necessity of added dissolved solids removal, such as iron, needing aeration, add to the problem of concentrating neutralized solids.

Jan 12, 1972

By William S. Springer

A NEW preparation plant has been put in operation to treat coal from the recently opened Concord mine, located about 15 miles west of Birmingham, Ala., by the Tennessee Coal, Iron & Railroad Co., a U. S. Steel subsidiary. The mine produces metallurgical grade coking coal from the American seam for use as coke in the company's blast furnaces at the Fairfield and Enseley works. The capacity of the operation is 1000 tons of run-of-mine per hr, approximately half of which is delivered to the by-product coke plant at Fairfield after beneficiation to metallurgical grade. The remaining portion of the mine run is rock and refuse removed during preparation. No boiler coal or other fuels are produced by this mine.

Jan 12, 1950

By John V. Beall

As Mother Nature arranged it, the hottest potential mineral target in the country today, the Stillwater complex had to occur in a spectacular natural setting-the north margin of the Bear Tooth Mountains of Montana. What more appropriate backdrop for the August 17-18 field hearings of Senator Frank E. Moss (D-Utah). His subcommittee, on Minerals. Materials and Fuels, heard 37 witnesses ponder the value of minerals vs esthetics or other uses of federal lands. On August 17, four Army Hueys swept the senatorial party, the press, Forest Service Officers and such distinguished witnesses as Montana Governor Forrest H. Anderson over the Custer-Gallatin National Forests, besting the thin air of 10,000 ft p1us, they set down on Iron Plateau.

Jan 1, 1971

By C. A. Sobotowski, J. Eagan

Computer programs applicable to coal mining have been available for some time, especially in the academic sector. However, the computer has not routinely been applied to actual mining operations. This paper discusses how a computer system was set up as an important tool in mining design and decision making. The project was completed within the allotted timeframe of two months by taking advantage of existing technology. Key points include the selection of programs to meet the specified needs of the project, conversion of the programs to be compatible with a computer of a different manufacture, simplification of the data entry process, development of procedures for using these programs, and an explanation of how the reports generated from the programs were used for mine planning and decision making.

Jan 1, 1983

By H. H. West

Modern mining is vitally concerned with the prompt, efficient movement of great quantities of bulk materials. It is not surprising, therefore, that intensive efforts are being directed toward improving effectiveness and reducing costs of materials handling systems. Historically, the operation of removing bulk material from a moving conveyor and depositing it in utilization or storage areas has been a high cost segment of the materials handling system. Since this operation is often performed by belt trippers, considerable attention has been focused on improvement of these devices. Frequently, the greatest opportunity for improving performance of these devices is the incorporation of remote or automatic control systems. This article describes tripper control systems developed by Kennecott Copper Corp. and explains the control philosophies used in designing these systems.

Jan 3, 1963

By B. Yarar

Samples of coal from an adit in the Fording River District of British Columbia showed hydrophilic properties between depths of 0-24.5 m (0-80 ft) and was naturally hydrophobic at greater depths. Laboratory experiments indicated that weathered samples (i.e., those mined at 0-24.5 m) could be upgraded by froth flotation at pH32 following slimes removal. The i.e.p. of samples varied regularly between pH = 1.6-4.1, the weathered fractions being at the lower end of the pH scale. These values followed a pattern comparable with the flotation behavior of samples. A patchwise structure for coal surfaces determining the resultant disjoining pressure which in turn determines flotation-non-flotation relationships is postulated.

Jan 1, 1983

By James Boyd

It is obvious that mining has been influenced to a high degree by political and economic events, many of which are of such a nature that the mining industry has relatively little influence in shaping them. I cannot present too optimistic a picture for the immediate future, although I feel that from the long-range standpoint one need not be pessimistic about the future of the mining industry. The population of the United States is continuing to increase and with it has come an expanded consumption of metals on a per capita basis. With this expansion there has and will continue to come the demand for more goods and in- creased products from our mines and our fabricating plants. World War

Jan 5, 1950

By Cyril Stanley Smith

The following table, which is composed of data given in the author's first paper on the thermal conductivity of copper alloys1, contains tile results which have been obtained by previous workers on the thermal conductivity of the copper-tin, the copper-phosphorus and the copper-tin-phosphorus alloys (the phosphor bronzes). a Dr. Ing. Diss., Aachen, 1909. Quoted by Schenk: Ann. der Phys. (1910) 32, 261. b Beibl. Ann. der Phys. (1906) 29, 178. c Jnl. Inst. Metals (1928) 39, 375. d Jnl. Inst. Metals (192.5) 34, 43. e Ges. Abhand. Kennt. Kohle (1919) 4, 400. Experimental Methods Since the method of obtaining measurements of the thermal conductivity was identical with that described in the author's previous paper

Jan 1, 1931

By Lawrence F. Schubert

Instrumentation is not a stranger to the minerals processing industry. In fact, very few plants now exist that haven't to one extent or another adapted operations to instrumentation. But with the rapid growth of such controls has come the need for effective departments composed of men trained to maintain and repair the instruments; here is where many firms fall short. The importance of the role an instrument department should play is underscored by the omnipotent effects which instruments often exert over an operation. Reserve Mining Co. is an example: while instrumentation at this taconite plant represents approximately 2% of the process equipment cost, a breakdown of instruments may result in the ineffective use (or complete shut-down) of the other 98% of plant investment.

Jan 7, 1966

By R. A. Turpin

Bethlehem Steel's Research Department is developing a set of computer programs as mine-planning tools for Bethlehem's coal mines. Several of these computer programs have been completed and have been in routine use by Bethlehem Mines personnel since early 1975. The production scheduling and ventilation planning programs have been installed on an interactive time-sharing computer. The use of time sharing allows mines in remote locations to access these planning tools through standard phone lines and low-cost computer terminals. The capabilities of the interactive production scheduling and ventilation planning programs are briefly described. The advantages of implementing them using time sharing are discussed. A case study illustrates some of the benefits that planning based on the use of these programs has already provided.

Jan 1, 1977

By G. E. Karantzavelos

Anew flotation process to recover alunite from low-grade alunite ores is described. The process begins with run-of-mine ore, reduced to less than 5 mm (0.2 in.), being preconditioned with the reagents before grinding and alunite flotation. From the preconditioning step, ore particles, impregnated with reagents, form pellets that subsequently disintegrate into the pulp during grinding. The second step is basically a standard alunite flotation step. Pilot plant test results show that an alunite concentrate assaying at least 85% alunite and less than 5% silica can be produced. Laboratory and pilot plant results were in excellent agreement, indicating that the new process is a viable means of alunite beneficiation. Plant results, using the new process, were superior to results from conventional alunite flotation procedure.

Jan 1, 1986

By W. E. Newberry

The Aspen Mining District is situated at the eastern edge of the system of stratified rocks of western Colorado, where this edge meets the ridge of metamorphic granite which divides the State into two unequal parts. In following the valley of the Roaring Fork westward from the continental divide towards Aspen, one passes through a country of granite and gneiss, with no sedimentary rocks until the town is nearly reached. At this point the Cambrian quartzites first make their appearance, lying on the granites, with a dip of from 30' to 45 to the northwest. Beyond these quartzites and conformably upon them lie dolomites, limestones, shales, porphyries and sandstones, gradually flattening in general dip as one proceeds westward, but much disturbed by local foldings and faultings.

Jan 1, 1890

By A. Mitchell, M. Etienne

VARIOUS'-3 reports on the electroslag remelting process refer to the "thin skin of slag" existing around the slag pool and the solidifying ingot, but none considers the various mechanisms by which this layer forms and thus influences the surface quality of the ingot. A vertical section4,5 of the Cao-CaF2-Al2O3 diagram is shown in Fig. 1 between CaF2 and 6Al2.CaO3 From this, it is seen that a typical "70:30" CaF2:A1a3 slag will solidify to produce 6Al2O3.CaO primary phase in a eutectic matrix. The commercial slags contain sufficient CaO to produce* this composition by both the

Jan 1, 1969

By Philip Lindstrom

T he Radon mine is in the north end of the Big Indian mining district in San Juan County, Utah. Hecla Mining Co. operated the mine from early 1955 to early 1964 through an operating agreement with Federal Resources, Inc. Development consisted of a 3-compartment, 690-ft shaft, 4 main levels driven on the ore horizon and a haulage level below the ore. Evaluation of physical and economic factors showed that this flat-dipping ore occurrence could be mined by a low-cost coal mining method. The value of the deposit was high and unusual pre¬miums were possible by clean mining. Complete extraction without loss of ore pillars, minimum ore dilution and high production per man were obtained by longwall mining.

Jan 12, 1964

By M. Hayri Erten

In this research the possibility of pelletizing high grade fluorsoar fines or flotation concentrates with the use of calcined colemanite as binder is investigated, and the room temperature and elevated temperature strengths of these pellets are compared with those of pellets which are obtained by using bentonite as binder. Pellets of 10-12 mm. size and having 10% calcined colemanite showed a much higher room temperature strength than those containing 5% benonite, both being endurated at 1000°C for 15 minutes. However, when the same batch of pellets were tested at elevated temperatures of 250º to 500°C, bentonite gave better results. X-ray tests showed that in the pellets endurated at 1000°C for 15 minutes the original crystal structure of fluorite mineral is preserved.

Jan 1, 1977

By Milton C. Neul

As recently as the mid-1930's, steam and rail haulage were still the primary means of moving large quantities of rock. However, 2- to 5-ton standard on-highway trucks were beginning to be used in the mining industry's efforts to lower haulage costs. It was quickly obvious that rubber-tired equipment was more flexible, faster and more maneuverable. The trend towards haulage trucks had begun. Now while savings were being realized, the severe operating conditions encountered in open pit operations proved too much for the lightly constructed frames, gasoline engines and highly inflated tires. As a result, a few years later, the first 10 to 15-ton, two-axle heavy duty trucks were designed specifically to operate under off-highway conditions.

Jan 3, 1966

US 4,183,899 - Flow process for chlorinating ilmenite. A laminar flow of a mixture of ore, a carbonaceous reductant, and chlorine gas or other chlorinating agent is passed through a reaction zone maintained at a temperature of 1350 to 1950°C and a product stream Including titanium tetrachloride is withdrawn from the zone. The atomic ratio of carbon to oxygen in the feed mixture is greater than 1:1, and the molar ratio of chlorine to titanium solids In the product stream is between about 0 5.1 and 2:l. Titanium chlorides and metallic iron are recovered separately from the product stream. J.P. Bonsack, assigned to SCM Corp, Jan. 15, 1980 21 pp. (423-79). Filed. 3-10-78 (885,442).

Jan 1, 1982

By E. C. Winegartner, A. A. Ubbens

The company attempting to sell coal to large utility plants is faced with a confusing array of quality parameters and specifications which are often poorly understood by both the utility company and coal supplier. While these specifications are placed on the coal by the utility company, many of them originate with the boiler manufacturer who must guarantee that his product will perform satisfactorily on the design coal. A proper understanding of these parameters by both the coal supplier and utility company can lead to a better understanding of their mutual problem. This paper brings together most of the parameters in common use today and attempts to show what the parameters mean to the boiler designer, particularly in the area of boiler slagging and fouling.

Jan 1, 1977

By H. Nakazawa, I. Iwasaki

Galvanic contact, occurring between electrically conducting minerals in flotation pulps, may affect the nature of mineral surfaces and influence their floatabilities. Rest potential and galvanic current measurements were made on an electrode combination of pyrite and pyrrhotite under nitrogen, air and oxygen aeration conditions. The results were correlated with their oxygen-consuming characteris- tics and flotation behaviors. The galvanic contact improved the floatability of pyrrhotite, but adversely affected that of pyrite. Auger electron spectroscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy indicated that the formation of hydroxide or oxide and sulfate species of iron on pyrrhotite decreased, whereas that on pyrite increased when these minerals were held in contact. An electro- chemical mechanism was proposed for the observed behaviors.

Jan 1, 1986