Search Documents

By George A. Komadina

The Pima mine lies 20 miles southwest of Tucson, Ariz., and 45 miles north of the Mexican border. It is located on a hillside overlooking Tucson, which allows for gravity flow generally through the plant. In April 1965, an expansion was authorized by the mine's board of directors. This will triple the mine's output to 18,000 tpd. At this rate, it is estimated that there is sufficient ore to last 20 years.

Jan 6, 1965

By Henry Mulryan

The largest and purest known deposit of diatomite is being actively mined and processed 3 1/2 miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Nlanville Products Corporation. The workings cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoe, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1938

By Henry Mulryan

The largest and purest known deposit of diatomite is being actively mined and processed 3 1/2 miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Nlanville Products Corporation. The workings cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoe, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1938

By Robert E. Allen

The organized curtailment of California oil production is not yet one year old but during its first year it has accomplished so much that it is now firmly established as an agency of economic efficiency. The principle of cooperative curtailment has been adopted by other states and it is safe to say that the principle will continue as long as the demand for petroleum is notably less than the potential production. It' is interesting to note that this same principle of regulating supply to meet demand is now being urged for other industries, such as agriculture and mining. Since Oct. 31, 1929, when curtailment was instituted by the oil producers of Santa Fe Springs and Long Beach in an effort to avert the disaster of ruinously low prices which confronted them, there has been a constant and increasingly effective curtailment program in California. Prior to that time a notable effort toward the restriction of oil production was made under the direction of F. C. Van Deinse during the early summer months of 1929. A considerable reduction of oil output was recorded as the result of this effort, but because of incomplete cooperation and the discovery of still deeper zones at Santa Fe Springs the effort was abandoned; flush field production became unrestrained and prices soon fell to low levels. This initial curtailment movement was educational and experimental. It showed all operators a way out of their overproduction difficulties and developed the principles followed in later curtailment efforts. Thus it was that only a few days after their oil had been reduced to 60 c. per barrel, the operators of Santa Fe Springs got together and agreed to restrict their current production of more than 270,000 bbl. daily to not more than 150,000 bbl. daily. The operators at Long Beach followed the same course a few clays later and agreed to limit their production to not more than 110,000 bbl. daily. The Santa Fe Springs operators chose H. P. Grimm as umpire and director of their proration program. Neal H. Anderson was chosen umpire for Long Beach. Since that time, as the need for curtailment has increased, practically every field of the state has come under the curtailment of these two umpires. Curtailment of the Elwood and

Jan 1, 1931

By A. Goldberg, T. E. Tietz, J. E. Dorn

Introduction The concept that the flow stress for plastic deformation of metals in the work hardening range is a function of the instantaneous values of the strain, strain rate and test temperature was promulgated by Ludwick' many years ago. This thought has been more or less a guiding principle throughout the immediate period of development and growth of mechanical metallurgy. It has been tacitly assumed or knowingly applied to many investigations on the plastic behavior of metals. Spurred by the theoretical interest and practical importance of the plastic behavior of metals, many investigators have attempted to determine empirical, semi-empirical, and theoretical equations2-l8 relating the flow stress with the strain, strain rate, and temperature. Although the applications of such equations have been extensive, the experimental verification of the existence of a mechanical equation of state is weak. Furthermore, some of the available evidence on plastic flow appears to suggest that no simple functional relation between stress, strain-rate, strain and temperature can exist. The mechanical equation of state demands that Where a = true stress = loadlinstantaneous area e = true strain _ Instantaneous gauge length ~ initial gauge length i = true strain rate T = temperature This formulation implies that da is an exact differential. Therefore the flow stress (a) is a function of the instantaneous values of the strain (c) the strain rate (i) and the temperature (T), independent of the previous mechanical or thermal history. Having reached a certain strain, strain rate, and temperature, by any path whatsoever, a definite and fixed value of the flow stress should be obtained. One check on the validity of the mechanical equation of state is easily obtained. Consider the following three tests on the stress-strain curve at constant temperature: A. Strain at rate :I B. Strain at rate it C. Strain at rate 11 to el and continue test at &. A graphical representation of possible results of such tests are shown in Fig I. If, for strains greater than el, test (C) data coincide exactly with the data from test (B), as shown in Fig ra, a limited verification of the mechanical equation of state is obtained for the range of strain rates from il to iz. But if the data from test (C) differ from those of (g) beyond strain t\ where the strain rate is changed from il to k2, the mechanical equation of state is not

Jan 1, 1949

R. F. MCELVENNY.- Over 20 years ago I went back East on a little tour of copper companies to see how copper was handled and fabricated, and I met a Mr. Bassett who took me through the Waterbury branche of the American Brass Co. I have not seen this gentleman for 20 years, but I have a letter from him that I would like to read to you. 'The American Brass Co. Waterbury, Conn. May 19, 1930. To the-Salt Lake City Conference on Reverberatory Smelting Practice: Through the courtesy of Mr. Scott Turner, Director of the U. S. Bureau of Mines, Mr. G. L. Oldright has been temporarily released from his regular duties to act as your secretary. We have asked him and Mr. McElvenny to make the necessary preliminary arrangements and to present to you at the opening session the greetings of the officers and' directors of the Institute. I am very glad that it has been possible for you to come together under the auspices of the Institute and that the acceptance of our invitation has been so very unanimous. Such an acceptance of the invitation to this meeting indicates your interest in getting together for an exchange of technical data and ideas. We anticipate that this meeting will be of real service to the smelting industry through your open discussion and exchange of ideas, and we sincerely hope that you will form an organization which will arrange for future meetings of a similar nature. While it probably may not be desirable to. distribute the minutes of this conference except to the members who take part in it, we hope that later the Institute publications may be enriched by such matter as you think it desirable to have published; and also, that some of you may be able to offer technical papers for the Institute publications. I hope that you will find a permanent organization desirable and trust that it will be possible for you to form such an organization so that conferences may be regularly called. We hope that you can make use of the Institute organization and that we can be of real service to your industry. With best wishes for your success in this undertaking, I am Most cordially yours, W. H. Bassett, President.

Jan 1, 1930

By David Turnbull

STAFF: Editor, Gerhard Derge Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: J. S. Smart, Jr., President; C. C. Long, Past-President; K. L. Fetters, Vice President; T. D. Jones, Treasurer; R. W, Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: C. L. McCabe, Chairman; H. L. Bishop, K. L. Fetters, J. J. Harwood, W. A. Krivsky, F. C. Langenberg, R. E. Lund, W. O. Philbrook, L. L. Seigle, R. L. Smith, and F. L. Vogel. Review and selection of monuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: C. L. McCabe, Chairman; R. E. Lund, Vice-Chairman; D. H. Baker, Jr., W. A. Krivsky, R. A. Lewis, Paul Queneau, A. S. Russell, R. E. Shinkoskey, W, W. Stephens, and M. E. Wadsworth. Institute of Metals Division: L. L. Seigle, Chairman, Paul A. Beck, I. I. Bessen, J. 0. Better-ton, Jr., J. B. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, R. B. Gordon, C. D. Graham, Jr., R. W. Guard, J. C. Gurland, E. L. Harmon, J. J. Heger, A. A. Hendricksan, M. Herman, J. N. Hobstetter, H. H. Johnson, Jr., R. R. Nash, T- N. Rhodin, R. H. Richman, W. Ros-toker, P. G. Shewmon, C. W. Spencer, L.SIifkin, J. K. Stanley, C. D. Starr, and H. C. Stumpf. Iron and Steel Division: H. L. Bishop, Chairman; R. E. Boni, F. C. Langenberg, J. B. Wagstaff, and T. V. Wainwright. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for non-AIME members in United States and North, South, and Central America; $25, foreign; $5 for AIME members. Single copies, $4.00, single copies foreign, $5.00. The AIME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1961 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AIME New York .. . Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 221, Number 3.

Jan 1, 1962

By Willard Jillson

WITHIN the last ten years Kentucky has become celebrated for its low-sulfur bituminous coals. Prior to this time, many investigators had discovered the abundance of this coal but the fact was unknown to the general public until the last extension of Kentucky's mountain railroads was completed. The coals of Kentucky are, broadly, separated into two geographic units-the eastern and the western coal fields. On a basis of their sulfur content these coal fields fall into three units, which are indicated on the accompanying map, by numbers, 1, 2, and 3. The area marked 1, the very southeastern part of the State, shows the lowest sulfur, all coals being averaged. In this field the maximum is 1.04 per cent. and the minimum as low as 0.68 per cent.-both averages and not individual analyses, which would of course show much greater variation. Included in this group are the following counties: Lawrence, 0.87 per cent.; Martin, 0.75 per cent.; Johnson, 0.73 per cent.; Magoffin, 0.S7 per cent.; Floyd, 0.88 per cent.; Pike, 0.68 per cent.; Knott, 1.04 per cent.; Perry, 0.77 per cent.; Letcher, 0.80 per cent.; Leslie, 0.70 per cent.; Harlan, 0.79 per cent.; Knox, 0.86 per cent.; and Bell, 0.92 per cent. The total average sulfur content for these thirteen counties is 0.82 per cent. Bordering the restricted low-sulfur field of eastern Kentucky is the No. 2 belt (slightly darker), which is commonly known as the western border of the eastern coal field. Here the maximum sulfur is 2.91 per cent. and the minimum 1.05 per cent. Again these are averages and not individual analyses. The counties in this group are: Greenup, 2.60 per cent.; Boyd, 1.67 per cent.; Carter, 1.07 per cent.; Morgan, 1.40 per cent.; Wolfe, 1.83 per cent.; Lee, 2.93 per cent.; Breathitt, 1.85. per cent.; Owsley, 1.09 per cent.; Jackson, 1.06 per cent.; Rockcastle, 2.30 per cent.; Clay, 1.09 per cent.; Laurel, 1.08 per cent.; Pulaski, 2.24 per cent.; Whitley, 1.05 per cent.; McCreary, 1.50 per cent.; and Wayne. The sulfur percentage average for this area including fifteen important counties is 1.65 per cent.

Jan 9, 1919

By Dennis K. Mortensen

The Role of the Operator The ultimate objective of any installation is to be able to accomplish the useful work that it was originally designed for. The operator needs a tool that he can both operate effectively and maintain efficiently. The overall design and subsequent installation of a comminution circuit should be a marriage of good engineering practice and practicality. Since the operator must operate and maintain his equipment, his input into the design and installation is vital to its ultimate success. The design of a crushing or grinding circuit is dependent upon many factors including flowsheet design, equipment selection, physical layout, space restrictions, climatic restrictions and considerations for future expansion. The operator must live on a day-to-day basis with the results of the final design and installation. The most satisfactory operation will result when the operator has a major input into each of the criteria that are used to define the final design and installation. The operator referred to is not only the mining company or organization that is having the installation built for its specific use but, more specifically, the person or persons that will actually be responsible for its daily operation and maintenance. Future references to the "operator" will include those individuals with that daily reponsibility. The operator's input into the installation of the circuit is of equal importance to his input into the design. The engineering organization which puts together all of the various design drawings for circuit installation is generally restricted to trying to get all of the details onto a multitude of 24" x 36" two dimensional drawings with a few isometric drawings thrown in. It's almost impossible to get all of the details of a final installation onto all of the drawings, and field modifications are necessary to make everything fit properly. In a multilevel installation, such as a grinding or crushing circuit, it is difficult to envision space requirements to adequately operate and maintain the various pieces of equipment simply by looking at a set o£ drawings. For some designs it is helpful to build a scale model so that a more realistic view of what the installation will look like can be seen. The scale model allows the operator to make whatever changes in design are needed to operate and maintain his equipment most effi-

Jan 1, 1982

The following is a list of members who died in 1928. It is compiled from reports to the Secretary's office. Biographical sketches published in Mining and Metallurgy are indicated in the last two columns. Issue Containing Year or Date or Biography Election Name Death 1928 Page 1914 Adams. David T.................... July 22 October 471 1905 Aguilera. Pedro................... May 3 October 469 1902 Althouse, H. W.................... NOV. 3 December 559 1920 Averill: C. C...................... July 9 October 471 1915 Baldwin, C. Kemble............... Aug. 9 October 471 1926 Barquist, Walter C............... NOV. 14 June 298 Barron,* Clarence Walker......... Oct. 2 November 511 1917 Beasley, Fred E.................... Aug. 31 October 471 1901 Belden, S. B....................... May 15 July 333 1927 Binney, Edwin, Jr.................. Dec. 29 February 96 1915 Bonsall, James Malcolm............ Feb. 12 June 284 1917 Boyle, John....................... July 12 December 561 1913 BradEn, Eugene B............. Jan. 29 March 157 1889 Bulkley, Frank.................... Mar. 25 May 240 1896 Callaghan, J. T., Jr............... Apr. 1 1892 Chalmers, George.................. Feb. 4 April 197 1898 Clark, Josiah H.................. May 7 July 333 1887 Copeland, F. K............. Nov. 10 December 561 1915 Cunningham, B. L11............... Dec. 6 August 294 1888 Dana, R. T........................ Aug. 20 December 559 1907 Dennis, Clifford G............... Dec. 28 March 1 1920 DeVenny, Thomas................ Feb. 13 April 197 1882 d'Invillier-, Edward V........... Jan. 4 March 157 1884 Duncan, M. M..................... Dec. 17 February 96 1924 Dyrssen, WaldemaR ............... Aug. 4 October 471 1906 Edmondson. H. W................ Dec. 21 February 1884 Emmerton, F. A.................. Oct. 9 June 298 1911 Eu, S. H............................ July 20 February 1917 Farrand, Ira W.................... Sept. 6 October 469 1900 Fell, E. Nelson...........•......... Mar. 25 May 231 1918 Fenton, Clarence M.............. October Junet 298 1908 Ferraris, Erminio................. Sept. 22 June 298 1914 Galloway. A. D. R............... December April 215 1924 Grant, A. W., Jr................... .4pr. 5 June 285 1917 Grant, Clifford G............... Jan. 26 January? 37 1918 Grant, Frank E.............. Jan. 14 September 417 1921 Gunderoth, C. J.................. Feb. 15 1897 Harms, Ernest..................... Aug. 12 November 512 1891 Hartrick, J. S..................... Feb. 9 June 285 1925 Hochschild, Berthold.............. Jan. 24 April 197 1917 Hutton, L. W...................... NOV. 3 January 37 1894 Jenning", S. J...................... NOV. 17 December 560 1925 Jones, J. Ravenscroft............... Jan. 29 March 157 1880 Jones, J. T......................... May 4 June 284

Jan 1, 1929

By Howard B. Bradley, Charles F. Weinaug

The phase behavior of a naturally occurring hydrocarbon system whose critical temperature is near the reservoir temperature has been described. The same volume per cent liquid was observed for the firkt time at three different pressures for isotherms immediately below the critical temperature. The shapes of the isothermal equilibrium constant curves necessary to predict this phenomena are discussed and illustrated. INTRODUCTION The phase behavior of a number of hydrocarbon systems has been reported; however, very little data are available on natural occurring hydrocarbon systems whose critical temperature is near the reservoir temperature. This appeared to be the case for the fluid studied here; therefore the pressure-volume-temperature data for this system were determined for preqentation. METHOD The PVT data were obtained with equipment similar to hat described by Weinaug and Katz,1 consisting principally of a two-section, double-windowed gauge mounted in a conktant temperature air bath. The procedure followed was essentially that used by Katz and Kurata5 except that a cathetom-eter, reading direct to 0.01 cm, was used to determine the height of each extreme phase limit. The system studied was formed by recombining -.vapor and liquid samples from the first stage separator of the well. Portions of these samples were displaced with mercury into the cell which had previously been filled with mercury. A predetermined amount of the liquid sample was introduced, while an excess of vapor was admitted. The resulting mixture was brought to equilibrium at the condition of the separator during sampling. By adding mercury to maintain the pressure, enough vapor was displaced to give a gas/oil ratio within the cell equal to that produced by the separator at the time of sampling. The remaining material was then considered to be equivalent to the reservoir fluid. An analysis of material in the cell, computed from analysis of vapor and liquid samples and the separator gas/oil ratio. is given in Table I. Table I — Composition of Hydrocarbon System Component Mole Per Cent Carbon Dioxide 0.13 Nitrogen 0.76 Methane 53.91 Ethane 14.20 Propane 9.64 Iso Butane 1.25 Normal Butane 4.29 Iso Pentane 1.12 Normal Pentane 1.87 Hexane 2.72 Heptanes + 10.11 hloleculal. Weight of Heptanes + 178.50

Jan 1, 1951

By Howard B. Bradley, Charles F. Weinaug

The phase behavior of a naturally occurring hydrocarbon system whose critical temperature is near the reservoir temperature has been described. The same volume per cent liquid was observed for the firkt time at three different pressures for isotherms immediately below the critical temperature. The shapes of the isothermal equilibrium constant curves necessary to predict this phenomena are discussed and illustrated. INTRODUCTION The phase behavior of a number of hydrocarbon systems has been reported; however, very little data are available on natural occurring hydrocarbon systems whose critical temperature is near the reservoir temperature. This appeared to be the case for the fluid studied here; therefore the pressure-volume-temperature data for this system were determined for preqentation. METHOD The PVT data were obtained with equipment similar to hat described by Weinaug and Katz,1 consisting principally of a two-section, double-windowed gauge mounted in a conktant temperature air bath. The procedure followed was essentially that used by Katz and Kurata5 except that a cathetom-eter, reading direct to 0.01 cm, was used to determine the height of each extreme phase limit. The system studied was formed by recombining -.vapor and liquid samples from the first stage separator of the well. Portions of these samples were displaced with mercury into the cell which had previously been filled with mercury. A predetermined amount of the liquid sample was introduced, while an excess of vapor was admitted. The resulting mixture was brought to equilibrium at the condition of the separator during sampling. By adding mercury to maintain the pressure, enough vapor was displaced to give a gas/oil ratio within the cell equal to that produced by the separator at the time of sampling. The remaining material was then considered to be equivalent to the reservoir fluid. An analysis of material in the cell, computed from analysis of vapor and liquid samples and the separator gas/oil ratio. is given in Table I. Table I — Composition of Hydrocarbon System Component Mole Per Cent Carbon Dioxide 0.13 Nitrogen 0.76 Methane 53.91 Ethane 14.20 Propane 9.64 Iso Butane 1.25 Normal Butane 4.29 Iso Pentane 1.12 Normal Pentane 1.87 Hexane 2.72 Heptanes + 10.11 hloleculal. Weight of Heptanes + 178.50

Jan 1, 1951

[Abstmct of remarks by R. II. Sweetser arid suhscqueut discussion at the New York Meeting, February, 1926. The Transactions mill ultimately contain a report of work resulting from these discussions. Need for a standard of ualuration.—There should be an accepted method for evaluating the different kinds of bituminous coals based on their carbon just as that for iron ores is based on iron. Variation in the classes of coals and their desirability fol the different industrial uses is analagous to the case of iron ores. The iron people have developed a standard. In the past coals have not been intelligently distributed because the public has not been informed as to its uses. Many operators have known nothing about the final disposal of the coal shipped from their mines. Sales agents and retailers have had no means of evaluating coals except to make the price as high as the market will stand. Producers and distributors need to know how much more valuable the coals would be if prepared so as to contain less objectionable material. Mr. Swectser cnlletl on the Goal and Coke Committee of the Institnte to organize a study through producers and users to develop a method scientifically and comnereially sound E. A holbrook said that the information exists but the public is unwilling to investigate. He praised Ashley's1 nomenclature of the different kind of coal which has been accepted by the Coal Mining Institute of America and recommended to the American Enginecring Standards Commitee. G. S. Rice pointed out the wider variety and distribution of consumption of coal compared to Iron ore. C'. M. Young approved Mr. Sweetser's remarks and hoped lor a research institution, probably endowed, to study utilization of coal after it comes from the ground. Mr. Sweetser cited incidents to prove his former statements. He said that a reduction of 1 per cent. ash in the coal would cut down the cost of pig iron at a blast furnace 30 c. a ton, that the coal men should tell what the iron men would have to pay to get better coal. H. J. Prryn endorsed the need of blast-furnace operators to know the kind of coal from which their- coke is made and the latler's ash content, as this affects coke consumption. A. C. Fieldncr explained that the difficulty of evaluating coal on the basis of chermical analyses for calorimetric tests is: (1) representativr

Jan 1, 1927

The following discussion occurred on the afternoon of Sept,. 22, 1930, as part of the fall meeting of the Iron and Steel Division at Chicago. About seventy-five men attended this session. C. B. Murray opened the meeting, as follows: C. B. Murray, Cleveland, Ohio.—It is very encouraging to see so many here this afternoon to discuss this important matter of beneficiation. The producers of ore, I am sure, are anxious to furnish the grade of ore that the consumer wants. The consumer sometimes wants that which cannot be economically produced and often the producer cannot understand why the consumer wants certain things. It was to bring together these two interested parties that this meeting was proposed. I was appointed the chairman of the meeting, chiefly because I happened to be the chairman of the Iron Ore Committee of the Institute. I know a little about iron ore but have not perhaps kept up with the times in blast-furnace practice. I am asking Mr. Sweetser, who is well informed from both sides, to take over the meeting and carry on the discussion. R. H. Sweetser, Columbus, Ohio.—We want to have a free discussion between the iron-ore men and the blast-furnace men as to just what we are trying to reach in the beneficiation of iron ores. Many of those present have had a great deal of experience. There are men here from the ranges who have been passing through the experimental stage of beneficiation of iron ores, and there are some who have already gone on to commercial production. We have reached the point where the beneficiation of iron ore is important to the whole iron and steel industry. The connection between iron-ore beneficiation and the cleaning of coal is so close that I think we can profit by working very close to the coal people. Some Aspects of the Iron-ore Situation W. G. Swart, Babbitt, Minn.—I was very much interested in Mr. Richards'* paper on tonnages and the 20-year life. There is one interesting thing about the ore reserves; that is, the irregular distribution of that tonnage. On the Mesabi Range, for example, the United States Steel Corpn. owns between 70 and 75 per cent. of the reserve tonnage. They ship bctween 40 and 50 per cent. of the annual Lake Superior

Jan 1, 1930

By C. W. Schultz, R. B. Tippin

Statistical screening is so named because a particulate feed is separated into "size" intervals on the basis of the probabalistic behavior of the individual particles (i.e., their probability of passing the screen) rather than by physical restraint. To illustrate this statement, consider a conventional screening operation. A particle which is larger than the openings in the screen cloth is physically restrained from passing through and is repeatedly reflected from the surface until it is discharged as oversize. Of those particles smaller than the screen openings, the very smallest tend to pass the screen near the feed end while those nearer in size to the screen opening tend to pass at a greater distance from the feed end. Alternatively, we could say that the particles with high probability of passing through the screen are concentrated near the feed end while particles of low probability of passing are dispersed from the feed end. This tendency to segregate is the basis for size separation by statistical screening. The purpose of this note is to: 1) Show that the distribution of material passing an array of screens can be described by a modified binomial distribution. 2) Demonstrate that an efficient size separation can be made by this technique. 3) Relate some of the more important screening parameters to the efficiency of the size separation. The Distribution Function The distribution of undersize products along the length of a screen can be derived with the help of a few simple definitions and assumptions. 1) First, we must assume that each particle has some probability of passing a screen on a single presentation. Further, we must assume that this probability is constant and is not affected by the position of the particle on the screen. It must also be acknowledged that several factors enter into this probability. Among them are the "action" of the screen, the slope of the deck, the shape of the openings, etc. The relationship between these factors, however. is not the subject of this paper. 2) To simplify calculations, all particles falling within a size range on the Tyler scale, e.g., —x + x/ mm, are assumed to have the same probability. 3) It is assumed that particles which do not pass the screen on a presentation are reflected a unit distance forward, i.e., the direction of material travel. A unit distance is defined as the distance between the centers of consecutive wires in the screen cloth.

Jan 1, 1971

By C. R. Kuzell

STAFF: Editor, Gerhard Derge Carnegie lnstitute of Technology Schenley Pork Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: C. C. Long, President; John Chipman, Past-President; J. S. Smart, Jr., Vice-President, T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMiTTEE OF THE METALLURGICAL SOCIETY: D. J. Carney, Chairman; Robert Maddin, Past-Chairman; J. H. Hollomon, J. H. Jackson, H. H. Kellogg, T. B. King, F. C. Langen-berg, D. L. McBride, W. O. Philbrook, J. S. Smart, Jr., R. L. Smith, J. D. Sullivan, and F. L. Vogel Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: H. H. Kellogg, Chairman; T. 8. King, Post-Chairmon; R. P. Hermsdorf, W. A. Krivsky, R. E. Lund, C. L. McCobe, Poul Queneou, A. 5. Russell, M. E. Wadsworth, and W. D. Wilkinson. Institute of Metals Division: R. L. Smith, Choirman; P. A. Beck, I. I. Bessen, J. O. Betterton, Jr., R. S. Davis, J. J. Gilmon, R. 8. Gordon, C. D. Graham, Jr., R. W. Guard, J. C. Gurlond, J. J. Heger, M. Hermon, J. N. Hobstetter, H. H. Johnson, Jr., I. R. Krarner, W. C. Leslie, R. A. Meussner, R. R. Nosh, G. E. Pellissier, T. N. Rhodin, A. U. Seybolt, L. L. Seigle, I. S. Servi, P. G. Shewmon, L. Slifkin, J. K. Stanley, C. D. Starr, and J. Washburn. Iron and Steel Division: F. C. Longenberg, Chairmon; H. L. Bishop, C. W. Sherman, J. 8. Wagstaff, and E. Whittenberger. Published bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for nan-AIME members in United States and North, South, and Central America; $25, foreign; $5 far AlME members. Single copies, $4.00, single copies foreign, $5.00. The AlME is not responsible for any statement mode or opinion expressed in its publications . . . Copyright 1960 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York ...Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts ... Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 218, Number 4

Jan 1, 1961

By C. W. Burrows

The burden a man can endure depends on its magnitude and the number of times it is applied, as well as on many other factors. The resisting power of steel likewise is dependent on many factors. The maximum load it can support indefinitely is much less than its possible momentary burden. A light load straining the metal far within its elastic limit, if repeated indefinitely, ruptures the metal. The magnitude of the stresses that may be alternately applied and removed without rupturing the material depends on the number of repetitions of the cycle; the intervening periods of rest; the thermal, electric, and magnetic conditions, as well as the presence of secondary streessses. While we are unable to formulate the law between the magnitude of repeated stresses necessary to produce rupture and the length of time during which these alternating stresses may be applied before rupture, my experience is that the time increases as the magnitude of the force decreases, according to a law which! to a first approximation, is exponential. In other words, F = Ce-t where F= magnitude of alternating stresses; t= time for which stresses are continued; C = constant, which depends on the conditions under which the operations are carried out. It is quite probable that the same type of law holds for the magnitude of a continuous force and its duration. When a rod of steel is subjected to the blows of a drilling hammer several things happen. First, one end is struck by the hammer and the other end is driven into the rock, thus causing a bodily displacement of the entire material of the steel drill. The greatest stresses involved in this bodily displacement are located at the two ends of the steel and manifest themselves by the distortion of these parts. Second, after the blow has been delivered, the steel drill, due partly to its own resiliency and partly to the resiliency of the rock, experiences a vibratory motion as a whole, this motion is quite similar to the bouncing of a rubber ball thrown violently upon a smooth pavement. Third, the free vibration of the drill is determined only by its own natural period of vibration. This motion involves all the characteristics of any vibrating body emitting sound. Certain elements of the rod will experience alternations of condensation and rarefaction and, in these regions, the individual steel

Jan 1, 1922

By George G. Griswold

The Parkes process of lead refining is based on the fact that when zinc isemixed with molten lead bullion, it forms an alloy with the silver and gold. This alloy freezes at a higher temperature and is of a lower specific gravity than the lead. With proper regulation of the temperature, the alloy solidifies and floats on top of the lead bath, from which it is removed and the silver, gold, and zinc recovered. The alloy should contain the maximum amount of silver (Ag2Zn,). The usual practice is to make two additions of the zinc. The first addition gives an alloy, or zinc crust, the zinc of which is saturated and is treated for the recovery of its zinc and silver; the crust from the second addition contains an excess of zinc and is used for the first addition on the following kettle. The crust produced depends on a number of items: purity of bullion, temperature, care with which kettle work is performed, addition of zinc, pressure used in expelling lead from crust, etc. It is desirable to make the concentration of silver in the zinc crust as high as possible; otherwise an undue amount of byproducts is produced, which greatly increases the cost of refining. It was formerly considered good practice to make a concentration of 20 :1. That is to say, if the lead bullion assayed 150 oz. dorê per ton, the assay of the retort bullion recovered from the zinc crust should be 3000 oz. per ton. As a matter of fact, the concentration should never, except on bullion assaying over 300 oz., be so low, and with low-grade bullion it should be 50:1. In one lead refinery where, ordinarily, the work was good, on a bullion averaging about 200 oz. per ton, a concentration of 24:1 was common; but how it was obtained was known only to the foremen. Changes occurred, and under new foremen the kettle work fell off badly; the problem then was to bring about this greater concentration. As is customary, the refincry had a "schedule" for its 60-ton kettles, which gave the number of pounds of zinc required for all possible assays, on both the first and the second zincing. Using this schedule, high temperatures

Jan 1, 1924

By Gerhard Derge

THE chemical and physical properties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use, These processes are carried out at high temperatures and involve such complex chemical systems that fundamental scientific knowledge of the properties and behavior of these slags is inadequate. Various hypotheses have been proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenck1 and the recent papers of Chipman and co-authors.2-5 Another proposal is that these compounds dissociate by completes or partial ionization, the evidence for which has been reviewed by Martin and Derge.7 Whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: I, Studies of solidified slag samples by X-ray diffraction, petrography, and similar methods that can be used at room temperature, The correlation of this information with the high-temperature properties of the molten slag is uncertain, 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature, However, even these data present problems of interpretation because they require a complete knowledge of the metal phase, 3, Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret, Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information, The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems CaO-SiO2 and CaO-A1203-Si02 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1946

By G. V. Kurdjumou

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J. S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. 0. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. V. Wainwright. Review and selection of manuscripts is under the supervision of the following Publications Committes: Extractive Metallurgy Division: R. E. Lund, Choirmon; M. E. Wodsworth, Vice Choirmon; D. H. Boker, Jr., G. M. Bell, R. E. Grace, W. A. Krivsky, R. A. Lewis, Chorles O'Neill, A. W. Schlechten, R. E. Shinko~ke~, and W. W. Stephens. Iron and Steel Division: T, V. Wainright, Choir- mon; ti. L. Bishop, R. E. Boni, T. E. Doncy, D. W. Murphy, Johonnes M. Uys, J. B. Wogstaff, ond R. G. Word. Institute of Metals Division: J. N. Hobstetter, Choirmon; P. A. Beck, J. J. Beckar, G. F. Boiling, J. O. Brittain, J. 0. Clark, R. 5. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifolco, J. C. Gurlond, H. S. Kolish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richrnon, H. C. Rogers, W. Rostoker, O. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, ond R. Swolin. PuUlished bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17, N. Y. Telephone PLaZa 2-6800. Subscription $30 peryear for non-AIME members in United States and North, South, and Central America; $32, foreign; $30peryear$7.50 for AIME members. Single copies, $6.00, single copies foreign, $6.50. The CentralAmerica;AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1962 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . .Copyright.Registered cable address, AIME New York . . . Indexed in Engineering Index, Industrial Arts Index, and Chemical cableaddres .. . AlME class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 3.

Jan 1, 1962