Search Documents

By Vernon E. Swanson, Tom G. Ging

Experiments indicate that simple addition of water to mixtures of untreated trona and otherwise insoluble leonardite yields a rich, black, slightly alkaline solution of concentrated humic substances. Prices of both trona from Wyoming and leonardite from South Dakota and Wyoming are very similar-$10-30 per ton. Leonardite is the term commonly given to naturally weathered, oxidized coal that is readily soluble in slightly alkaline water.1 Several tens of thousands of

Jan 1, 1973

By Michael B. Bever, John R. Anderson

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By John R. Anderson, Michael B. Bever

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By W. T. Bishop, G. A. Crowe

While the literature in the United States on general polarographic technique is extensive, very little appears to be directly applicable to the analysis of flotation tailings. For this reason, it seemed worth while to present a few polarographic methods of ore analysis that have been in constant use in the laboratories of the Hercules Experiment Station for the past few years. At the time of our initial investigation of the polarographic method, there was little or no mention of its specific application to flotation tailings. It was therefore necessary for us to establish suitable conditions for the analysis of our flotation tailings and to consider possible interfering constituents. The polarograph, or dropping mercury electrode, method was discovered in 1925 by J. Heyrovsky and M. Shikata,1 of the Charles University, Prague. This method has since received extensive development and the literature contains many articles on the use of the polarograph for the quantitative determination of metals as well as anions, oxygen in solution, and reducible organic compounds. Kolthoff and Lingane,² by the publication of their book, "Polarography," in 1941 did much to advance the knowledge and use of the polarograph. In chapter 25 of that book, methods for the polarographic analysis of brass, steel and iron products, alloys, and zinc ore are given. Aluminum,³ cadmium,³,4 cobalt,4 cop-per,³-9 gold,10 iron,3,11 lead,³,l2,l³ molybdenum,14 nickel,4,8,9 tin," and zinc³,4,5,7 in ores have been analyzed by the polarograph. However, most of the work on tailing samples has been published in Russian journals and translations are not yet readily available. In this paper we will describe the method that was developed and used in our laboratory for the determination of copper, zinc, and lead in flotation tailings. Principle OF the Method The polarograph is an instrument for applying a potential to a mercury pool and a dropping mercury electrode separated by a solution, and for measuring the resultant electrical current. The procedure is essentially a small-scale electrolysis, in which the voltage required to reduce or oxidize the material identifies it qualitatively and the current measures the concentration quantitatively. Different constituents in a sample may often be determined simultaneously provided they reduce at sufficiently different voltages. An example is the determination of copper and zinc in the same solution. The reduction potentials are quite far apart, as shown in Fig. I. The polarographic method is particularly useful in the range of concentration between those normally determined by spectographic and chemical methods. In

Jan 1, 1947

By G. A. Crowe, W. T. Bishop

While the literature in the United States on general polarographic technique is extensive, very little appears to be directly applicable to the analysis of flotation tailings. For this reason, it seemed worth while to present a few polarographic methods of ore analysis that have been in constant use in the laboratories of the Hercules Experiment Station for the past few years. At the time of our initial investigation of the polarographic method, there was little or no mention of its specific application to flotation tailings. It was therefore necessary for us to establish suitable conditions for the analysis of our flotation tailings and to consider possible interfering constituents. The polarograph, or dropping mercury electrode, method was discovered in 1925 by J. Heyrovsky and M. Shikata,1 of the Charles University, Prague. This method has since received extensive development and the literature contains many articles on the use of the polarograph for the quantitative determination of metals as well as anions, oxygen in solution, and reducible organic compounds. Kolthoff and Lingane,² by the publication of their book, "Polarography," in 1941 did much to advance the knowledge and use of the polarograph. In chapter 25 of that book, methods for the polarographic analysis of brass, steel and iron products, alloys, and zinc ore are given. Aluminum,³ cadmium,³,4 cobalt,4 cop-per,³-9 gold,10 iron,3,11 lead,³,l2,l³ molybdenum,14 nickel,4,8,9 tin," and zinc³,4,5,7 in ores have been analyzed by the polarograph. However, most of the work on tailing samples has been published in Russian journals and translations are not yet readily available. In this paper we will describe the method that was developed and used in our laboratory for the determination of copper, zinc, and lead in flotation tailings. Principle OF the Method The polarograph is an instrument for applying a potential to a mercury pool and a dropping mercury electrode separated by a solution, and for measuring the resultant electrical current. The procedure is essentially a small-scale electrolysis, in which the voltage required to reduce or oxidize the material identifies it qualitatively and the current measures the concentration quantitatively. Different constituents in a sample may often be determined simultaneously provided they reduce at sufficiently different voltages. An example is the determination of copper and zinc in the same solution. The reduction potentials are quite far apart, as shown in Fig. I. The polarographic method is particularly useful in the range of concentration between those normally determined by spectographic and chemical methods. In

Jan 1, 1947

By A. H. Geisler, R. F. Mehl, C. S. Barrett

The complicated nature of the property changes that accompany age-hardening has made it necessary to reconsider and to elaborate the simple dispersion theory.l It has been apparent for some time that more direct information is needed concerning the atomic mechanism of precipitation from solid solution if the theory of age-hardening is to be developed past a purely qualitative stage.‡ Fortunately, in recent years information has been developed which allows us to trace in detail the lattice changes accompanying the process of precipitation from solid solution. This information relates chiefly to the sequence of the several stages of lattice alteration by which the matrix lattice is transformed to the equilibrium precipitate lattice, and permits reasonable inferences to he drawn concerning the states of internal strain that accompany these stages. This information is most complete for the solid solution of copper in aluminum. The equilibrium precipitate is the 0 phase, "CuAl2." This forms in plates, parallel to the {100} matrix planes. The atom pattern and atom spacing on the plane in 0 lying parallel to this plane are roughly similar to those opposite it in the matrix.3 The formation of 0, however, is preceded by the formation of a transition lattice 0': which again lies parallel to the matrix {100} plane, but in this case the matching of atom pattern and spacing across the matrix-precipitate interface is nearly periect; thus there is lattice coherency across the interface and the interface is a plane of separation in only a very limited sense.'8 Particles of 0' may be recognized microscopically and form a well-defined Wid-manstatten figure.* The 0' lattice is recognized by the occurrence of diffraction lines on powder photo-grams or of spots on Laue photograms which may be analyzed in the usual ways to determine the lattice type and the lattice spacings. Very recent research 6, 7, 1 has shown, however, that streaks occur on the Laue photogram at an earlier point in time during the aging process. These streaks have been attributed to a preferential clustering of copper atoms into small platelike elements of only a few atoms in thickness and a lew hundred atoms in diameter, probably of the composition of " CuA12," which may be designated as Guinier-Preston zones or aggregates.1 It is difficult if not impossible to determine the lattice type and lattice spacing in these aggregates. It is possible1 that these aggregates are in fact ?' in a high State of dispersion; the inclination to argue this is strong, as we shall see later. Never-

Jan 1, 1941

By R. F. Mehl, C. S. Barrett, A. H. Geisler

The complicated nature of the property changes that accompany age-hardening has made it necessary to reconsider and to elaborate the simple dispersion theory.l It has been apparent for some time that more direct information is needed concerning the atomic mechanism of precipitation from solid solution if the theory of age-hardening is to be developed past a purely qualitative stage.‡ Fortunately, in recent years information has been developed which allows us to trace in detail the lattice changes accompanying the process of precipitation from solid solution. This information relates chiefly to the sequence of the several stages of lattice alteration by which the matrix lattice is transformed to the equilibrium precipitate lattice, and permits reasonable inferences to he drawn concerning the states of internal strain that accompany these stages. This information is most complete for the solid solution of copper in aluminum. The equilibrium precipitate is the 0 phase, "CuAl2." This forms in plates, parallel to the {100} matrix planes. The atom pattern and atom spacing on the plane in 0 lying parallel to this plane are roughly similar to those opposite it in the matrix.3 The formation of 0, however, is preceded by the formation of a transition lattice 0': which again lies parallel to the matrix {100} plane, but in this case the matching of atom pattern and spacing across the matrix-precipitate interface is nearly periect; thus there is lattice coherency across the interface and the interface is a plane of separation in only a very limited sense.'8 Particles of 0' may be recognized microscopically and form a well-defined Wid-manstatten figure.* The 0' lattice is recognized by the occurrence of diffraction lines on powder photo-grams or of spots on Laue photograms which may be analyzed in the usual ways to determine the lattice type and the lattice spacings. Very recent research 6, 7, 1 has shown, however, that streaks occur on the Laue photogram at an earlier point in time during the aging process. These streaks have been attributed to a preferential clustering of copper atoms into small platelike elements of only a few atoms in thickness and a lew hundred atoms in diameter, probably of the composition of " CuA12," which may be designated as Guinier-Preston zones or aggregates.1 It is difficult if not impossible to determine the lattice type and lattice spacing in these aggregates. It is possible1 that these aggregates are in fact ?' in a high State of dispersion; the inclination to argue this is strong, as we shall see later. Never-

Jan 1, 1941

By W. H. Smith

IN connection with some recent work on the effect of impurities on the ductility of chromium, it appeared desirable to know the solid solubility of carbon in chromium. A literature survey indicated that this information was not available. Although considerable work has been done on the Cr-C phase diagram,&apos;.&apos; previous investigators have been more concerned with the structure and phase boundaries of the carbide phases than with the terminal solid solution. The phase diagram shown in Fig. 1 is taken from the work of Bloom and Grant&apos; and represents the most recent determination. As indicated by the dashed line, the a solid-solubility limit was not determined. Experimental Procedure Alloys of chromium were prepared from hydrogen-treated and vacuum-degassed electrolytic chromium plus spectrographic grade carbon. The oxygen and nitrogen content of the alloys was <0.002 pct. After melting, analysis of the alloys showed them to contain 0.02, 0.08, 0.15, and 0.55 pct C. Pieces of the alloys were heated in a protective atmosphere to various temperatures and then quenched after holding for a time sufficient to insure equilibrium. Microscopic examination of the as-quenched alloys for the presence of a second phase was used as a measure of the solubility limit. The heats were made in a multiple hearth arc-furnace using a zirconium-gettered static argon atmosphere. A zirconium melt was made before each Cr-C heat. Triple melting was used to insure ingot homogeneity as shown by microscopic examination. The alloys were prepared by adding portions of a 4.5 pct C-Cr master alloy to high purity chromium. The carbon contents listed previously were those obtained by analysis. The nitrogen and oxygen contents after arc melting were both <0.002 pct. Sections 1/8X1/4X1/2 in. were cut from the 100-g ingots and a hole drilled in one end in order to suspend the sample from a molybdenum wire. After the surface was carefully cleaned, a sample of each melt was hung in a mullite tube heated externally by a platinum resistance furnace connected to a vacuum system. The lower portion of the mullite tube was sealed to Pyrex and closed off several inches below the furnace. This was filled with sili-cone oil kept cold by circulating cold water around the outside of the Pyrex. Quenching into the oil bath was achieved by melting a fuse wire supporting the sample. It required about 4 sec for the sample to cool from 1400" to 600°C. This severity of quench was considered satisfactory to freeze-in the high temperature equilibrium. For tests made at temperatures of 900" to 1200°C, heating was done in vacuum; for tests above 1200°C, an argon atmosphere was used. The holding time employed ranged from 12 hr at 900°C to 6 hr at 1400°C. Experiments were performed at temperatures of 900°, 1000°, 1100°, 1200°, 1300°, and 1400°C. Microscopic examination for evidence of a second phase was done at X1500. Experimental Result The microstructures of a 0.08 pct C-Cr alloy as-cast and after quenching from 1300°C are shown in Figs. 2 and 3. A 0.15 pct C-Cr alloy quenched from 1300°C is shown in Fig. 4. The data obtained from the quenching experiments is shown graphically in Fig. 5. If the Van&apos;t Hoff equation is obeyed, a plot on a logarithmic scale of the mol fraction of solute vs the reciprocal of the absolute temperature should give a straight line. For dilute solutions the weight percentage can be substituted for the mol fraction without introducing any appreciable error. The Van&apos;t Hoff equation can then be written as where H is the heat of solution in calories per mol. The slope of the straight line on the log pct C vs 1/T plot gives the value of AH. Assuming that the Van&apos;t Hoff equation is obeyed, which is probably justified for the dilute solution of carbon in chromium, the heavy straight line shown on Fig. 5 represents the best fit of the data. This line was obtained as follows. On Fig. 5 the results of the microscopic examination of all alloys following quenching were plotted and designated as to whether one or two phases were seen. Below 1100°C all alloys showed a second phase on quenching. The heavy vertical lines shown in Fig. 5 therefore represent the possible range of the ter-

Jan 1, 1958

By N. A. Gokcen, J. Chipman

A revised treatment of the authors&apos; published data eliminates the complex relation previously proposed between concentration of silicon and activity coefficient of oxygen in liquid iron. Revised values of the thermodynamic properties of the liquid solution are presented. IN a recent experimental study of the reaction SiO2 (s) = Si+ 2O; Kf, = [% Si] [% O]² [1] the authors&apos; found a substantially constant equilibrium product in liquid iron at 1600°C of 2.8x10-5 They also reported extensive data on the reactions: SiO2 (s) + 2H2 (8) = Si- + 2H2O (g); K&apos;2= [% Si] (H2O/H2 [2] and H, (g) + 0 = H2O (g); K&apos;3 =( H2 O [31 (H2) [%O] From the results on reaction 3 and earlier data of Dastur² on this same reaction in the absence of silicon, they determined the activity coefficient of oxygen, f0, on the basis of the definition K3 = (H2O)/ (H2)f0 [% 0] where K, is the equilibrium constant and f0, is taken as unity in the pure Fe-0 system. Similarly values of fsi were deduced from results on reaction 2. In a more recent study" of analogous reactions in the system Fe-A1-0, it was found impossible to reconcile the results on reaction 3 with Dastur&apos;s data; accordingly the latter were ignored and the equilibrium results were extrapolated to find a value of K, at zero concentration of aluminum. This procedure failed to locate the cause of the discrepancy but it did yield reasonable values of activity coefficients. It also avoided introduction of the complex empirical relation between the oxygen activity coefficient and the concentration of the added element. The same type of discrepancy exists for system Fe-Si-0.&apos; In the earlier paper an attempt was made to fit both sets of data by a single curved line (Fig. 6 of ref. l), the form of which is contrary to the theoretical requirement of a finite slope at infinite dilution. In the light of experience on the Fe-A1-0 system the discrepancy must be recognized as one which can be resolved only by more refined measurements. Accordingly Figs. 6 and 10 are retracted. It is pointed out also that until the discrepancy is resolved Figs. 7, 8, and 11 are subject to some uncertainty. Qualitatively the following conclusions still appear valid: 1—The activity coefficient of oxygen is reduced by addition of silicon. 2—In dilute solutions the activity coefficient of silicon increases with its concentration. 3—With respect to equilibrium in reaction 1, the above effects are approximately compensating. The discussion of K&apos;1 in the previous paper requires no revision. It was pointed out that the constancy of the product [% Si] [% 0]² ndicated a compensating effect of the activity coefficients of silicon and oxygen. Therefore, as a very good approximation, K1 = K&apos;1 and the following average values are suggested both for K, and K&apos;, at the temperatures 1550°, 1600°, and 1650", respectively, 1.0x10-", 2.8~10-" and 5.5 ~lo-&apos;. Revision of the thermodynamic treatment is necessitated by the recent appearance of new data, based on a combination of combustion and solution calorimetry,&apos; which yields for the heat of formation of low-cristobalite from the elements, the value —209,330 ±250 cal per mol at 25°C. This is about 4000 cal larger than the value previously accepted. The new value for cristobalite is used, together with Kelley&apos;s tables of high-temperature heat contents" and entropies and with Korber and Oelsen&apos;s&apos; heat of fusion of silicon to obtain the following equation for the standard free energy of cristobalite in the temperature range 1700" to 2000°K: Si (1) + 02 (g) = Si02 (crist.); ?F° = -217,700 + 47.OT [4] The free energy of solution of 0, in liquid iron is:8 O2 (g) = 20 (in Fe); AF° = -55,860 - 1.14T [5] and these two equations are combined to give: Si (1) + 20 = SiO, (crist.); AF° = -161,840 + 48.14T [6] ?F°1873 = -71,700 cal. From the experimental value of K, = 2.8x10-5, Si + 20 = SiO2 (crist.); ?F°1873 = -39,000 cal. [7] The combination of Eqs. 6 and 7 yields the free energy change when liquid silicon dissolves in iron to form the dilute solution of unit activity (1 pct). Si (1) = Si; ?F°1873 = -32,700 cal. [8] The heat effect in this process according to Korber and Oelsen&apos; is an evolution of 28,500 cal per gram

Jan 1, 1954

By J. J. Becker

Changes in magnetic properties with particle size are used to study the precipitation process in a Cu-Co alloy. In particular, the effect of a field during aging in producing anisotropy is shown to occur entirely during the growth of the particles, after precipitation is complete. HEAT-treatment in a magnetic field is done commercially to improve the magnetic properties of a number of materials. These can be divided into solid-solution alloys and precipitation alloys. The Permalloys are representative of the first type, and magnetic annealing greatly increases their maximum permeability. On the other hand, in precipitation alloys such Alnico 5 the important result is an increase in maximum energy product. The effect of the field in all cases is to bring about an additional magnetic anisotropy, uniaxial in nature, which makes the hysteresis loop more upright when measured in the direction in which the field was applied. The structural origin of the anisotropy brought about by magnetic annealing is not well understood. In the solid solution alloys, one possible explanation is based on ordering.&apos; Another possibility is the orientation of like-atom pairs.&apos; The precipitation systems known to respond to magnetic heat treatment are Alnico 2, in which the effect was first discovered," Alnico 5, cobalt ferrite (oxide),&apos; and Cu-Co alloys.3 n these materials, the field affects the precipitation process itself in some way. Although there has been much work on Alnico 5. its nature is still incompletely understood. According to Geisler,&apos; the precipitation reaction is of the

Jan 1, 1959

By O. B. Hopkins

The total production of oil in Peru in 1940 was 12,127,135 bbl., or about 10 per cent less than in 1939. Most of the reduction can be attributed to the fact that the export market under war conditions is much restricted and naturally is more than ordinarily competitive. Development and Exploration in Older Areas As evidenced by Table I, almost all production continued to come from the three established fields in coastal northwestern Peru. Zorritos Field.—Exploration in this small field, which was purchased by the Peruvian Government in 1939, continued with that in near-by areas in the adjoining National Reserve. Several wells were drilled, regarding which details are not as yet available. It is estimated that the production rate for a total of some 45 old and 15 new wells approximated zoo bbl. per day, or about 3 bbl. per well per day. Lobitos Fields.—The Lobitos area produced 2,435,504 bbl.; about 10 per cent less than the amount for 1939. La Brea-Pari9zas.—This property of International Petroleum Co. continued to account for nearly 80 per cent of Peru&apos;s production. During the year, drilling was stepped up to 139 wells, as compared with 73 wells completed in the previous year; 123 were producers and aggregated a total of 287,867 ft. Of this total, more than 85 per cent was drilled by rotary tools, which are steadily displacing other equipment. Although most of these wells were drilled in the proved or semiproved areas, eight

Jan 1, 1941

By O. B. Hopkins

The total production of oil in Peru in 1940 was 12,127,135 bbl., or about 10 per cent less than in 1939. Most of the reduction can be attributed to the fact that the export market under war conditions is much restricted and naturally is more than ordinarily competitive. Development and Exploration in Older Areas As evidenced by Table I, almost all production continued to come from the three established fields in coastal northwestern Peru. Zorritos Field.—Exploration in this small field, which was purchased by the Peruvian Government in 1939, continued with that in near-by areas in the adjoining National Reserve. Several wells were drilled, regarding which details are not as yet available. It is estimated that the production rate for a total of some 45 old and 15 new wells approximated zoo bbl. per day, or about 3 bbl. per well per day. Lobitos Fields.—The Lobitos area produced 2,435,504 bbl.; about 10 per cent less than the amount for 1939. La Brea-Pari9zas.—This property of International Petroleum Co. continued to account for nearly 80 per cent of Peru&apos;s production. During the year, drilling was stepped up to 139 wells, as compared with 73 wells completed in the previous year; 123 were producers and aggregated a total of 287,867 ft. Of this total, more than 85 per cent was drilled by rotary tools, which are steadily displacing other equipment. Although most of these wells were drilled in the proved or semiproved areas, eight

Jan 1, 1941

By Albert F. J. Bordeaux

This paper briefly describes the general outline of cyaniding silver-ores in Mexico, with special reference to personal experiments made in the Temascaltepec district. The most important papers on the subject deal with cyaniding gold-silver ores, the gold predominating in value, so that the treatment is nearly the same as for gold-ores, the losses of silver being considered of little importance. I describe here the treatment of silver-gold ores containing very little gold, which is more general in Mexico than elsewhere. The cyanide treatment, which was so successfully applied to gold-ores, did not succeed immediately with silver-ores on account of their varying composition. Gold occurs in nature usually in the native state, while silver occurs generally in combination with sulphur (argentite), and various combinations of sulphur, antimony, and arsenic. In former times there mas a complete difference in the treatment of gold-ores and silver-ores. Amalgamation, which was successful with gold-ores, was generally inadequate with silver-ores. The usual treatment in Mexico for silver was the patio process, the theory of which was satisfactorily explained only quite recently by Mr. Ortega and others. General Outline of the Cyanide Treatment. The general tendency of the present practice is to slime the silver-ore as much as possible, and in order to obtain a higher efficiency, with less loss of cyanide, and greater speed, the following lines are observed: 1. Crushing by stamps with 30- or 40-mesh screens, then crushing by Huntington or Chilean mills, through 60- or 80-mesh screens. 2. Concentration upon vanners.

Jan 1, 1910

By H. N. Lawrie

This study was undertaken on account of the lack of definite knowledge concerning the influence of bismuth on wire-bar copper, and the small elimination of bismuth from copper-matte during the smelting-operations. The early workers who studied the influence of bismuth on copper confined their investigations to malleability and ductility—two physical properties which are related to the others so intimately that their determination is of primary importance. Karsten and Levo1,² using bending- and mealleability-tests, seem to have been the first to take up the subject, and while their results are incomplete, they agree in the main with the later work of Hampe.3 The bending-tests used by the first investigators consisted in bending the specimen until it failed. The malleability-tests were made by beating the material to a knife-edge with a hammer. Hampe not only determined the percentage of bismuth which would cause red-shortness and cold-shortness of the alloy, together with other influences of bismuth on the malleability and ductility of copper, but also took up the influence of the bismuth protoxide, BiO, on copper, and of bismuth sesquioxide, Bi,O,, on the copper protoxide, CuO. Hampe&apos;s conclusioris of the influences of these two latter compounds of bismuth on copper are as follows : "If the protoxide of bismnth be alloyed with metallic copper, it is not changed to metallic bismuth, but remains mechanically distributed throughout the copper.

Jan 1, 1910

By Keith C. Hendrick

The mining industry of Canada, stretching from coast to coast and reaching into the most remote regions of the country, is of fundamental importance to the national economy and the well being of many communities outside the main urban areas. The production, processing and transportation of a host of mineral products provide employment for about 9% of the country&apos;s labour force; and their shipment to export markets provides an important contribution to the balance of payments. In 1976 Canada&apos;s metal and mineral production had a value of $5.24 billion, of which zinc and lead accounted for $862 and $129 million respectively, or 19% of the total. By all standards the Canadian zinc and lead industry is large and, therefore, important to the country as a producer and the world as a supplier. This report will review the development, describe the present status and discus current problems and future potential of the industry. The discovery and successful development of the major lead-zinc deposits at Kimberley, British Columbia, provided Canada with a solid base from which to grow. The breakthrough in metallurgical technology using differential flotation to separate the lead and zinc sulphides and the refining of high purity metal by electrolytic methods not only helped Canada to compete with other world producers but also provided a new source of these metals at prices and qualities that encouraged the development of new end uses.

Jan 1, 1977

By Paul Sterling

The general impression regarding the preparation of merchantable anthracite is that it is confined to a colossal, grimy structure, called a " coal-breaker." This name is a misnomer; for the desired result is not to break the coal, but to prevent its being broken. Preparation may be said to begin at the face of the chamber, with the mining and loading of the coal. Local conditions vary, not only ill the same field or basin, but also in the same mine, so that there is no fixed empirical rule governing the method of blasting or cutting coal. Tests should be made, when possible, to determine the explosive, or the mechanical coal-cutter, which will produce the largest percentage of what are locally known as " lump " and " prepared sizes " of anthracite. The prepared sizes are those mostly consumed for clomestic purposes. All other sizes might be called by-products of the anthracite industry; for they are not especially desirable, being the degradation resulting from the mining and handling of a brittle or laminated material. Being low in volatile combustible matter, anthracite burns most successfully when nearly of a uniform size, permitting the easy passage of air through the voids. This accounts for the large number of sizes into which the coal is separated. Table I. gives the various sizes, the diameter of ring over and through which each size is made, and the usual purpose for which it is employed.

Jan 1, 1912

By J. R. Dolegowski, W. S. Jensen, S. M. Olafson, W. H. Champion, G. A. Kordosky

The use of pH control in solvent extraction circuits to aid in metal separation, concentration, and purification is an extremely useful technique applicable to a wide range of solutions. This paper discusses the technique in general and then gives examples of its use in extraction stages, wash and/or scrub stages, and in stripping stages, to effect the desired metal separation, concentration, and purification. Specific examples cited include Cu-Ni, Cu-Zn, and U-Mo separations using commercially available liquid ion exchange reagents.

Jan 1, 1982

By Harold Markus, Gerhard Derge, Arthur Grobe

THE high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as terne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys.1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. APPARATUS AND METHOD The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from ½ to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.† After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been clamped. The pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. ± 0.1°. Potentials were measured against a saturated calomel electrode connected to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By Harold Markus, Arthur H. Grobe, Gerhard Derge

THE high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as terne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study. has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys.1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. APPARATUS AND METHOD The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from 1/2 to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.? After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been damped. The pH of the electrolyte was controlled? by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. ± 0.10. Potentials were measured against a saturated calomel electrode connected. to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By LUIS EAIYLNN SALAS

IF the ordinary wet method be attempted for silver-bullion containing tin, much trouble is experienced, varying with the amount of tin present. Even with a percentage as low as 0.05, the end-point is masked by a persistent turbidity, while with amounts ranging from 0.5 per cent. upward, the determination of the exact end-point is impossible, owing to the finely divided or colloidal metastannic acid resisting all efforts to cause it to settle, or to give a clear supernatant liquid. The object of the following experiments was to seek a remedy for these difficulties, and to find the conditions whereby the Gay Lussac method might be applied directly to these bullions. Material containing tin is met with frequently in bullion from Mexico or Bolivia; and tin is carried (sometimes in large quantities) in jewelers&apos; sweeps. 1. A bullion was prepared containing Ag, 74; Cu, 25; and Sn, 1 per cent. A weighed amount was treated by the humid assay-method as if it were an ordinary bullion free from tin. Ten cc. of HNO3 (1.21) was added, and the bottle was heated until all traces of red fumes had been expelled. Before heating, the solutions were moderately turbid; and after heating, the turbidity greatly increased. One hundred cc. of normal NaCl solution was added and the bottle was shaken vigorously at intervals during 30 min. The turbidity persisted. The bottle was allowed to stand over

Mar 1, 1912