Search Documents

By D. H. Davis, I. Fatt

Oil bearing rocks, usually found at depths of 2,000 to 10,000 it, are elastically deformed by overburden pressure. Although the change in porosity with pressure in a number of example rock.: has been shown to be small, it was thought that overburden pressure might have a significant effect on permeability. This note presents results of an investigation to determine the magnitude of the change in permeabilty with pressure. In routine core analysis permeabilities are measured on rock samples which are not under overburden pressure. If permeablity measured in this way differs from permeabilities measured under overburden pressure, a systematic error is introduced into well productivity calculations. The experiments described in this report were made to determine the magnitude of the change and thus to give an estimate of the error introduced into the calculations. The error introduced by the neglect of the change in permeability when overburden pressure is removed may account for part of the difference between well productivity calculated from core analysis and the actual well productivity. The results obtained in this investigation have only quali-tative significance because of the difficulty in reproducing in the laboratory the stress conditions on the rock buried in the earth. The assumption which is usually made is that the rocks in the earth are under a uniform pressure equal to the weight per unit area of the vertical overburden column from the rock in question to the surface of the earth less the pressure of the liquid in the pores of the rock. For an overburden consisting of sandstones and shales (of assumed average specific gravity of 2.3) and for a liquid pressure equal to the pressure in a salt water column (of specific gravity 1.0) reaching from the rock to the surface, the resulting net pressure on the rock is approximately 0.56 psi per ft of depth. EXPERIMENTAL METHOD Clean, dry sandstone core plugs one in. in diameter and about three in. long were mounted in a copper foil jacket as shown in Fig. 3 or molded in a Lucite jacket as shown in Fig. 4. All cores except those labeled "2" in Fig. 1 and "8" in Fig. 2 were measured in the copper foil jacket. Cores "2" and "8" were measured in the Lucite jacket. The jacketed core was placed in a high pressure hydraulic bomb in which the liquid pressure outside the jacket could be raised to 15,000 psi. Flow lines from the core were brought out of the bomb through special fittings in the bomh head and connected to a laboratory type gas permeameter. Measurements were made with nitrogen gas; the maximum mean gas pressure in the core was 16.1 psia. RESULTS The specific permeability of sandstone decreases with in. crease in overburden pressure. Most of the decrease takes place over the range of zero to 3,000 psi overburden pressure. If the net pressure on the rock is assumed to be 0.56 psi per ft of depth as discussed above, 3,000 psi of overburden pressure is equivalent to about 5,000 ft of overburden. At 3,000 psi overburden pressure, the permeability of the eight sandstone core samples tested ranged from 59 to 89 per cent of the permeability without overburden pressure. Figs. 1 and 2 show the permeability reduction as a function of overburden pressure. The permeability of the eight cores without overburden pressure ranged from 4.35 md to 632 md; these permeabilities are listed in Figs. 1 and 2. REFERENCES 1. Carpenter and Spencer: "Measurements of Compressibility of Consolidated Oil Bearing Sands," U. S. Bureau of Mines, R.I. 3450, (1940). * * *

Jan 1, 1952

By Cyril Stanley Smith

ON the 6th of February 1684, Dr. Martin Lister mentioned at a meeting of the Royal Society1 that "brass is magnetical," and promised to give an account of that assertion at some other time. He repeated his promise but never fulfilled it, and it was left for William Arderon2 to show, in 1958, that brass could be made magnetic by hammering and that it would retain polarity after magnetizing. Twenty-seven years later Cavallo3,4 examined the matter in great detail. Working with cast calamine brass, he showed that it could be made magnetic by hammering and nonmagnetic by subsequent annealing at a red heat. He found that annealing at a very high temperature caused the samples to lose their magnetic quality permanently, even after subsequent cold-working, but that remelting and cold-working restored it. He encountered some samples of brass that could not be rendered magnetic by any treatment. Experiments in which these were remelted with iron additions gave negative results, and Cavallo concluded that iron impurity was not the cause of the magnetism. He worked with 50-grain (3-gram) samples melted under the blowpipe, hence cooled very quickly. Bennet5 made whole crucible charges from copper and zinc, and found the resulting brass ingots to be magnetic only when iron had been added and then only after cold-working. All these observations applied to material in the cast condition, in which coring would produce a continuous spectrum of composition and cooling would result in varying degrees of precipitation. This knowledge of the subject seems to have been forgotten in the nineteenth century. The older brass was made by the calamine process and frequently contained iron in amounts of 0.5 per cent or more, absorbed from the impure ore with which the copper and charcoal were heated in making the brass. When metallic zinc became available in commercial quantities, calamine brass gradually disappeared, and with it the knowledge of its curious magnetic properties. Only when sensitive apparatus replaced the compass needle of the earlier investigators could the effects be detected in relatively pure metal. The effect of cold-working in inducing ferromagnetism was rediscovered by Bitters in 1930 in a sample of impure copper, and this was confirmed by Lowance and Constant,9 Honda and Shimizu, 10,11 and others. In the same year, Tammann and Oelsen12 showed that copper-rich copper-iron alloys after certain heat-treatments could be rendered ferromagnetic or made more strongly ferromagnetic by cold-rolling. Kussman and Seeman13 showed that the change of susceptibility of relatively pure copper on cold-working was associated with the iron content, and concluded that actual precipitation of iron was caused by cold-working, which is a satisfactory theory until one considers the improbably high rate of diffusion that this would involve. When studying precipitation phenomena in

Jan 1, 1941

By J. F. Gallie

From the standpoint of exploration and new discoveries, South Arkansas had a discouraging year in 1944. In January there were 73 untested drilling blocks, and 60 additions were made during the year. Of the total, 65 were condemned by dry holes on or adjacent to them, while 5 proved productive. The latter resulted in the discovery of the Salem Church, Calhoun Wilks, and Strong fields, and the extension of the Village field to the southeast. The year ended with 63 untested blocks, 41 of which were scheduled for tests to the Smackover lime, the state's deepest oil-producing formation. Geophysical activity in 1944 totaled 164 crew weeks, of which 110 were seismic, 43 gravity, and 11 radioactive (Fig. I), in contrast with 674 crew weeks reported for 1943, of, which 563 were seismic and in gravity, Five seismograph and two gravity crews were engaged in exploration in South Arkansas during January 1944. but only two seismograph crews were working there at the end of the year. In addition, exploratory core drills were used for a total of 38 weeks during the year. The year's few discoveries, none of which is considered as having added appreciably to state reserves, were the meager results obtained in the drilling of 62 wildcat wells 2000 ft. or deeper. Of this total (a detail of which appears in Table 2), 42 were drilled to the Smack-over lime or below, The average depth of the 62 wells was 5384 ft., as compared with 4992 ft. in the preceding year, while the average depth of the 42 wildcats in the lime was 5913 ft. in 1944. Fig. 2 has been prepared to show all , wells penetrating to the Reynolds oölitic lime. The 1944 dry holes are circled lightly, while discoveries are heavily circled and shown as producers. Smackover lime fields, producing from the Reynolds oolitic lime member, are indicated in black, and the locations of dry wildcat wells drilled prior to 1944 are also shown. Table 3 provides a listing of all Smackover lime wells drilled through the end of 1944. Production for the year was slightly more than in 1943, totaling 29,282,747 bbl., as compared with 27,521,943 bbl. for the preceding year. The increase was 1,760,804 bbl., or 6.4 per cent, bringing production to a peak exceeded only in the 1923 to 1928 period of flush production from the older shallow fields, principally Smackover. The increase was largely attributable to additional development in the Dorcheat-Macedonia, Atlanta, Fouke, Stephens-Smart, Haynesville, and Village fields, little production deriving from 1944 discoveries. These six fields accounted for loo of the 122 field wells drilled during the year. Annual and cumulative production for the producing life of the state are presented graphically in Fig. 3. Fig. 6 has been prepared by the author to show the producing ages and present known productive limits of all fields in South Arkansas. Production data, as usual, are assembled in Table 2, and provide a further breakdown of producing formations in the individual fields.

Jan 1, 1945

By William A. Johnson

THE mathematical analysis of diffusion curves in solid metals is Carried out ordinarily by analogy with the flow of heat in a continuous medium and no account is taken of the fact that the materials involved are composed of discrete particles that move discrete distances at irregular intervals. It is possible to treat the problem on the basis of simple assumed atomic mechanisms, in which case, because of the small scale of the elementary process compared to the gross effects observed experimentally, the two procedures lead to the same expression for the variation of concentration with distance. Thus, for engineering purposes, the usual methods are quite satisfactory. If, on the other hand, our purpose is to go beyond the mere collection of data, however desirable this may be, it is necessary to recognize and understand the factors that are of fundamental importance. One factor that has not hitherto been considered when dealing with solid metals is the difference in atomic weights of the isotopes of a single metal. While all the atoms of a given element are alike chemically, their weights may vary by a small but significant amount, and atoms of different weights may have different diffusion rates. With gases this variation in isotopic weight produces a change in the rate of diffusion by a factor inversely proportional to the square root of mass. While, except for the lightest gases, this is not a large effect, it is, for example, sufficient to permit a considerable concentration of one isotope at the expense of others. If metals exhibit a similar phenomenon, some modification of the analysis of the diffusion process will be required, since the different isotopes of a given metal will have different probabilities of moving and the heat-flow analogy will contain a fundamental error. This situation cannot be rectified by using a diffusion coefficient based on the average probability of moving, and it can be shown that even when the diffusion coefficient is independent of composition, the diffusion curve will not agree with the simple theory except in the rare cases where only one isotope exists; e.g., gold. If, however, the mass effect in the solid state were no larger than in the gaseous, the errors arising therefrom in the analysis of ordinary diffusion curves would be quite negligible. Nevertheless, our desire to obtain all possible information concerning the details of the diffusion process, and the possibility of diffusion in the solid state as a means for separating isotopes are cogent reasons for undertaking an experimental study to determine whether isotopes of different masses diffuse at different rates. EXPERIMENTAL PROCEDURE If isotopes of different masses diffuse at different rates, the ratio of the concentration of one relative to another will vary with the distance from the diffusion inter-

Jan 1, 1946

By D. E. Wolfson, H. J. Gluskoter, M. R. Geer, John A. Harrison, H. F. Yancey, I. S. Latimer

When this chapter was prepared for the kst edition in 1942, continuous mining machines virtually were unknown, and hand loading in underground mines, which gave an opportunity to discard impurities, accounted for 55 percent of the production of bituminous coal and lignite as compared with the 1965 figure of 11 percent. Only 24 percent of the total production was cleaned mechanically, compared with the present (1965) figure of 65 percent. The amount of refuse discarded during preparation for the same period increased from 13 to 21 percent. Changes in the equipment used in the cleaning process were as follows: [ ] Unclassified nearly 8 percent. Data on the amount cleaned by flotation was not collected until 1960 when 1.8 million net tons was so treated. In 1965 this figure increased to 6.9 million tons. Although the great increase in mechanization and full seam mining has resulted in substantial increases in the impurity content of the raw coal as well as in a finer size consist, some phases of face preparation are still important, particularly the variability of the distribution and thickness of the interbedded impurities and the changes in the character of the roof and floor from place to place in the mine. Knowledge of these factors in relation to all phases of the mining operation, particularly selective mining, are still of importance to the treatment of raw coal in the preparation plant. The major characteristics of coal and impurities from the standpoint of mechanical cleaning are particle size composition, generally called size consist, density differences, the relative friability of the coal and of its associated impurities, hardness, and strength. Some of the other factors related to preparation are petrographic composition and rank. COAL PROPERTIES Rank Perhaps 95 percent or more of the coal cleaned mechanically is of bituminous rank. Only a very small tonnage is subbituminous and prac-

Jan 1, 1968

By J. J. Bowman

The term "secondary aluminum" frequently is used loosely and often is considered synonomous with "inferior quality." Under war conditions, when every pound of material must contribute its share to the job at hand, this type of thinking is most unfortunate. Actually, given a supply of segregated scrap, an experienced smelter can produce remelted ingot of good quality, comparing closely to the analysis of the original material, and of considerable value of the war effort. The alloys he can produce are, of course, somewhat controlled by the analysis of the available scrap and, by the very nature of things, some of his production is not suitable for indiscriminate use. However, remelted scrap ingot provided about 273,2 per cent of this country's domestically-produced 1942 aluminum supply and probably will comprise about 39 per cent of the 1943 supply. (Canadian production is excluded from these figures.) That this part of the supply remains important is indicated by a recent report that "requirements" for the second quarter of this year were about 14 per cent greater than the supply, even though that supply will be almost twice the prewar annual production. (And those requirements, incidentally, were prepared after many conservation measures had been taken into account.) Since W. Bonsack recently has published a paper2 on the effects of the various alloying elements and impurities on the properties of aluminum, and such con¬siderations really are the important ones in a discussion of the metallurgy of secondary aluminum, it is planned to restrict this discussion more to a consideration of the sources, general characteristics and possible uses of these materials. For the purpose of this discussion, mill (or run-around) scrap may be disregarded and only plant scrap and obsolete scrap considered. Plant scrap, of course, is that scrap which is generated during the production of some part or assembly from a fabricated form of aluminum, such as sheet, tubing, forgings, castings or the like, and it may consist of solids (including rejected parts or subassemblies) or of machinings. To the extent that the several alloys are effectively segregated and the material is properly identified, the composition after remelting can be rather closely controlled or predicted. Obsolete scrap, on the other hand, is the "junk" which accumulates because of the wearing out or breakage of some piece of equipment. Although it is almost always in the form of solids, the accumulation includes many different alloys (often in the same assembly) and may include a considerable amount of nonaluminum material. The "metallics" recovered from drosses also contribute a portion of this class of material. The composition after remelting, therefore, may vary over rather wide limits and can not be very accurately predicted in any specific instance. SEGREGATION OF PLANT SCRAP Unfortunately, perhaps, it was not very common practice before the war to

Jan 1, 1943

By A. Patton, F. N. Speller

The use of roll scale in the Bessemer process dates back, to the best of our knowledge, at least 20 years. It was first used by the Ohio Steel Go., Youngstown, Ohio (now the Ohio Works of the Carnegie Steel Co.) under the direction of Sam McDonald, Superintendent of the Bessemer Department at these works. Two 10-ton vessels and one blowing engine capable of blowing one heat at a time were employed. The object of using the scale was to shorten the length of the blow, or in other words, to increase the production with the same equipment. Various means were tried out for introducing the roll scale into the bath of molten iron: It was shoveled into the vessel before the heat was charged, so that the metal would flow over the scale; it was shoveled into the bath after the vessel was turned up; it was dumped into the empty iron ladle by the wheelbarrow-load, and at times was dumped on top of the molten metal in the iron ladle. But the practice of introducing the scale into the iron ladle had to be abandoned on account of danger from explosions and of skulling the ladles. It was soon learned that the proper place to charge the scale was in the empty vessel, so that when the molten iron was poured into the vessel it flowed over the scale, causing a considerabIe reaction to take place before the heat was turned up. Eventually, cylindrical chutes similar to those now in use were installed. Into these chutes the scale is dumped and carried into the empty vessel. Before this convenient means of introducing the scale was adopted, the Ohio Works had satisfactorily demonstrated that roll scale would increase production, by blowing 107 heats in one 12-hr. turn (1,087 tons) with one blowing engine, blowing one heat at a time; whereas, prior to the use of scale, the best practice at these works was about 80 heats under the same conditions. In using roll scale and other oxides of iron to facilitate and control the refining of pig iron in the converter, the Bessemer plant has borrowed one of the most active agencies used in the open-hearth process with, as would be expected, much the same results. The effect of such additions to the Bessemer charge may be discussed as to the influence of this practice on quality, production and cost.

Jan 1, 1917

By Joseph J. Becker

RECENTLY the "oriented growth" hypothesis of recrystallization textures has been receiving considerable attention. According to this view, "whenever a new generation of grains is growing in a highly oriented matrix . . . one may assume . . . that from among available nuclei of a great variety of orientations those with suitable orientation relationship with respect to the matrix have by far the highest rate of growth (oriented growth) and will, therefore, predominate."' This statement includes primary recrystallization of single crystals and of polycrystalline materials showing strong deformation textures as particular cases. While the phenomenon of oriented growth undoubtedly does operate, and may be of importance in coarsening or secondary recrystallization, the writer feels that its extension to primary recrystallization is a different matter. Several aspects of this phenomenon may be pointed out which are difficult to rationalize on the basis of oriented growth. In recrystallizing deformed single crystals of alpha brass, Maddin, Mathewson, and Hibbard2 found that the twin composition planes of the recrystallized grains were parallel to the three operative slip planes they observed, and not to the fourth octahedral plane. The writer's current work seems to indicate further that when only one or two slip systems can be seen to operate, the recrystallized grains are aligned only with those slip planes actually observed. This behavior could hardly be accounted for by oriented growth, because on the latter basis the recrystallized texture of a deformed single crystal should certainly have the same symmetry as the crystal itself. Growth rates could not be expected to distinguish between crystallogra- phically equivalent directions, unless the presence of a visible slip system vastly increases the growth rate in the appropriate direction. This seems unlikely. These relationships were observed by the writer only when considerable care had been exercised before annealing to etch away the effects of cutting out the centers of tensile specimens with a jeweler's saw and to etch off the ends of compression specimens. When these.precautions were not taken, nu-cleation inevitably appeared to occur at the saw cuts or at the ends, and the resulting orientations never showed a [111] rotation but appeared quite random. The provision of many nuclei of many orientations did not enhance the correlation, but destroyed it. Recrystallization textures are sometimes strongly dependent on annealing temperature, which would imply that the anisotropy of growth rates is a suddenly varying function of temperature. This might be regarded as unlikely. Recrystallization textures can be strongly dependent on the degree of deformation. If textures are to be explained by selective growth from among nuclei of all orientations, it is difficult to see how the recrystallization process could have any dependence whatever on the manner or degree of deformation. It is felt that the above points should be considered before the oriented growth hypothesis is applied to primary recrystallization, with the necessary complete divorce of the mechanism of recrystallization from the details of the deformation process. References 1P. A. Beck and H. Hu: Reply to discussion of their paper on Recrystallization Texture and Coarsening Texture in High Purity Aluminum. Trans. AIME, 188, 1057; Journal oF Metals (Aug. 1950) TP 29083. 'R. Maddin, C. H. Mathewson, and W. R. Hibbard, Jr.: The Origin of Annealing Twins in Brass. Trans. AIME, 185, 655; Journal of Metals (Sept. 1949) TP 26763.

Jan 1, 1952

By D. V. Carter, D. C. Williams

Four oil discoveries were made in east and east central Texas during 1940, three of which represented new fields. In the Chapel Hill field, Smith County, oil was found where formerly only gas and distillate were produced. The three oil fields discovered are: Hawkins, Wood County; Pittsburg, Camp County; and Tehuacana, Limestone County. Important extensions were made to the following fields: Bazette, Navarro County; Long Lake, Anderson and Leon Counties; Cayuga, Anderson, Freestone and Henderson Counties; Opelika, Henderson County; and Talco, Titus and Franklin Counties. At the close of the year 54 oil and gas fields were producing in the district. There were 13 other fields, 11 oil and 2 gas, which have been abandoned. The East Texas field led the district in the number of completions for the year. During the year about 622 wells (oil and distillate wells included) were completed and 80 wildcats were drilled. Production and Proration During the year 170,424,685 bbl. of oil (distillate production included) were produced in the district—a decrease of 2.6 per cent from the 175,053,729 bbl. (distillate production included) during the preceding year. The district's production for the year 1938 was 182,369,484 bhl. As usual, most of the district's annual production was in the East Texas field, which produced 139,095,694 bbl. (distillate production in- cluded) during 1940, or 81.6 per cent of the total oil produced as compared with 141,333,317 bbl. (80.7 per cent) for 1939. The December estimated daily average production in the district was 424,565 bbl. The district accounted for 34.9 per cent of the state's annual production, compared to 36.7 pcr cent of the state's 1939 production. The decrease in production for 1940 may be attributed to changes made in proration schedules. Any material changes in the district's annual production may be considered for the most part as a reflection of proration-schedule changes affecting the East Texas field, since it is by far the most important field in the area. The entire state was subject to 71 shutdown days for the year; the East Texas field to 131; and the Rodessa field (Cass County, Texas, portion) to 5 days. No important changes were made in field rules and regulations during the year regarding the allocation of oil in individual fields in this district. Discoveries The Hawkins field is in southeastern Wood County in and principally north of the town of Hawkins. Development to date indicates that the field is somewhat of an elongated anticline trending slightly east of north and the proved oil area appears at this time to cover approximately 4000 acres. The oil production has been secured from the Woodbine sand, Upper Cretaceous; a considerable quantity of gas has been encountered in the Sub-Clarksville formation (Eagleford shale) in the higher part of the structure. It appears that a free gas

Jan 1, 1941

By D. C. Williams, D. V. Carter

Four oil discoveries were made in east and east central Texas during 1940, three of which represented new fields. In the Chapel Hill field, Smith County, oil was found where formerly only gas and distillate were produced. The three oil fields discovered are: Hawkins, Wood County; Pittsburg, Camp County; and Tehuacana, Limestone County. Important extensions were made to the following fields: Bazette, Navarro County; Long Lake, Anderson and Leon Counties; Cayuga, Anderson, Freestone and Henderson Counties; Opelika, Henderson County; and Talco, Titus and Franklin Counties. At the close of the year 54 oil and gas fields were producing in the district. There were 13 other fields, 11 oil and 2 gas, which have been abandoned. The East Texas field led the district in the number of completions for the year. During the year about 622 wells (oil and distillate wells included) were completed and 80 wildcats were drilled. Production and Proration During the year 170,424,685 bbl. of oil (distillate production included) were produced in the district—a decrease of 2.6 per cent from the 175,053,729 bbl. (distillate production included) during the preceding year. The district's production for the year 1938 was 182,369,484 bhl. As usual, most of the district's annual production was in the East Texas field, which produced 139,095,694 bbl. (distillate production in- cluded) during 1940, or 81.6 per cent of the total oil produced as compared with 141,333,317 bbl. (80.7 per cent) for 1939. The December estimated daily average production in the district was 424,565 bbl. The district accounted for 34.9 per cent of the state's annual production, compared to 36.7 pcr cent of the state's 1939 production. The decrease in production for 1940 may be attributed to changes made in proration schedules. Any material changes in the district's annual production may be considered for the most part as a reflection of proration-schedule changes affecting the East Texas field, since it is by far the most important field in the area. The entire state was subject to 71 shutdown days for the year; the East Texas field to 131; and the Rodessa field (Cass County, Texas, portion) to 5 days. No important changes were made in field rules and regulations during the year regarding the allocation of oil in individual fields in this district. Discoveries The Hawkins field is in southeastern Wood County in and principally north of the town of Hawkins. Development to date indicates that the field is somewhat of an elongated anticline trending slightly east of north and the proved oil area appears at this time to cover approximately 4000 acres. The oil production has been secured from the Woodbine sand, Upper Cretaceous; a considerable quantity of gas has been encountered in the Sub-Clarksville formation (Eagleford shale) in the higher part of the structure. It appears that a free gas

Jan 1, 1941

By G. St. J. Perrott

One of the important hazards in coal mining is the danger of ignition of explosive mixtures of methane and air or coal dust and air, or both, by the explosives used in blasting the coal. It has long been recognized that certain explosives are more dangerous than others in this respect. ' In America and abroad, government testing stations have been established for officially passing on the suitability of explosives for use in coal mines. In this country the Federal government is given no power to enforce the use of the approved explosives but merely publishes from time to time, through the Bureau of Mines, those explosives which have passed the tests necessary to place them on the list for use in coal mines. In spite of this lack of police power, the increase in the use of permissible .explosives since the promulgation of the fist list in 1909 has been rapid. In 1912, only 8 per cent. of the explosives used in coal mines were permissible; in 1925, this figure had increased to 25 per cent. While the past record of permissible explosives has been most gratifying, it is very desirable that we pave the way for further improvement in explosives and blasting methods by learning more about the mechanism of ignition of gas and coal dust by explosives. To this end a considerable amount of investigative work already has been carried out and a large amount yet remains to be done. It is the purpose of this paper to discuss briefly the effect of the characteristics of explosives and method of loading in the borehole on the liability of a blown-out shot to ignite explosive mixtures of gas or dust. For an account of the methods by which an explosive is tested for permissibility for use in coal mines, the reader is referred to Schedule 17-A of the U. S. Bureau of Mines. Safety Factor in Using Explosives The factors that affect the liability of an explosive to ignite gas or dust are already known in a qualitative way but quantitative data are

Jan 1, 1927

By William Kent

About a year ago, the writer had occasion to assist Mr. John L. Gill, Jr., of the Pittsburgh Car-wheel Works, in malting a trial of his new testing machine. A piece of Bessemer steel, of about .34 carbon, was used as a test-piece, turned to a sectional area of one square inch for a length of five inches between shoulders, and provided with large round heads, which were fitted to what is called the " Wade grip." Measurements of elongation, accurate to 1/10000 of an inch, were made by a special apparatus containing two micrometer screws, with electric contact attachment. The machine was operated by hand-power. Readings of elongation were taken at each increment of 2000 pounds stress per square inch, up to 44,000 pounds, the elongation corresponding to the latter figure being .0085 inch. The elongations up to this point remained almost exactly proportional to the stresses, the strain diagram, as shown on the Plate, from the origin to the point A, being a straight line (the deviation of no observation from the straight line being greater than .0002 inch). There being no indication of an approach to the elastic limit, the attendant at the hand-wheel and scale-beam wits told to proceed as usual and move the poise forward 2000 pounds, or to 46,000, and turn the wheel until the beam was balanced. Noticing that the beam did not rise in the usual time, and that the elongation was increasing rapidly, the writer called to the attendant to stop turning the hantl-wheel and to push the poise backwards until the scale-beam balanced. Instead of balancing at between 44,000 and 46,000 pounds, as was expected, it balanced at 40,000 pounds, and the elongation had increased to .0343 inch (or more than four times that recorded at 34,000 pounds), as plotted at the point B, the dotted line between A and B showing the supposed course of' the strain diagram between these two points. Immediately upon recording the elongation the writer said to Mr. Gill, who was standing alongside: "This phenomena is without a parallel in my experience, and I know of but one way to account for it. The piece. must actually be broken in its interior, through a flaw or weak portion of the metal. The test-piece is now equivalent to a tube, with

Jan 1, 1880

By Frank Marotta, Louis B. Lesem, Frank Greytok, John J. McKetta

Although one of the primary variables in the calculation of the flowing bottom-hole pressure in gas wells from surface measurements is the temperature at any point and its distribution in the flow-string, only few experimental data are available in the literature and little attention has been given to analysis of the problem. Virtually all of the recently published methods of calculating flowing bottom-hole pressures depend on the assumption that either the temperature is constant at some average value or that the variation is linear with depth. The purposes of this work are to analyze the problem theoretically and to verify the analysis by comparison with experimental data so that practical problems in the analysis of the behavior of gas wells can be solved with greater accuracy, reliability, and ease. MATHEMATICAL OUTLINE OF PROBLEM Assuming that: 1. The mass velocity and chemical composition of the gas stream are constant and in normal gas well operations, the change in linear velocity in the entire flow-string is trivial, 2. The product of the density and heat capacity of the gas is constant, 3. No horizontal temperature gradient exists in the gas stream, 4. Net flow of heat by conduction within the formation and in the gas stream in the vertical direction is trivial in magnitude and can be neglected, 5. The regional vertical geothermal gradient is constant, and 6. The temperature of the gas entering the borehole is constant, and equal to that of the reservoir, a set of two simultaneous, linear partial differential equations with appropriate boundary conditions was derived to describe the temperature distribution in the gas stream and the surrounding formation. These equations were solved by operational techniques for the distribution of temperature in the gas stream. The resulting integrals were evaluated numerically on an IBM 604 at the Machine Accounting Div. of the Railroad Commission of Texas. DERIVATION OF FUNCTIONS FOR THE DISTRIBUTION OF TEMPERATURE The physical system is a circular hole of radius a in an infinite medium with thermal conductivity K, density p8, and heat capacity c,. Under shut-in conditions the well is in thermal equilibrium with the surroundings and the increment in temperature is given by - ?T3/L x. Gas of density pg and heat capacity c.. flows upwardly through this hole in the direction of increasing x with a linear velocity W. Writing a heat balance on an element of gas ?x in thickness, convective heat transfer + conductive heat transfer + energy required to lift a unit mass of fluid = change in energy content. pa2W po Co To - pa2Wpo Co To x+xx - 2apK?x ?T8/?r r=a - Wpa2 po?x/778 = CoPopa2?x?To/?t... Dividing by (copopa2?x) and taking the limit as ?x tends to zero, -W (?To/?x + 1/778Co) + 2 K/a Po Co ?T3/?r r=u = ?To/?t

Jan 1, 1958

By Bernard Greifer, Walter Rose

The purpose of this note is to call attention to a source of difficulty which can be responsible for inaccurate estimates of wetting liquid pressure gradients in mixture flow experiments of the Hassler1 type. It has been our experience occasionally to observe what were indicated to be negative pressure gradients, and these were regarded as anomalous in the sense that physically they seemed to contradict the requirement that the flux be in the direction of the potential field. At first it was thought that our scheme of assembling barriers and core sample led to such asymmetry in the distribution of isobars that the manometric leads at each end of the core were responding to internal pressures (within the core sample) which could be either positive or negative with respect to each other, and which in fact might tend to reflect on different effective core lengths in an unpredictable fashion as the wetting liquid saturation was changed. However, no compelling evidence of this possibility has been established. In addition, we were cognizant of the requirements to be satisfied in selecting manometric instrumentation to minimize the delay in response of the manometer to the differential pressures being measured, and were thus assured that our observations of anomalous pressure gradients could not be explained by faulty instrumentation. What we suggest is that if a leak sink occurs in the fluid lines connecting the core to either side of the differential manometer, errors exceeding 100 per cent may result in the estimation of wetting liquid pressure gradient, even though the leak is of such small magnitude that its existence would tend to be obscured by evaporation effects. This is because in a system with leaks at the specified places, the manometer rec- ords at steady state the pressure drop across the manometer barrier elements in addition to the pressure drop across the core sample. This possibility will be illustrated below analytically and by numerical example for the special case where the leak occurs on the high presure side of the core, since we are especially desirous to explain the significance of our observations of the so-called negative pressure gradients. It will be indicated, however, that leak sinks on the low pressure side of the core can account for observations of anomalously high values of pressure gradient, and that multiple leaks on both sides of the core can provide for some compensation so that the errors in pressure estimation are reduced. However, the major point to be emphasized is the fact that the impractical-ity of detecting the small leak sinks which give rise to the difficulties makes it a complicated task for the experimenter in a particular case to know with certainty that his estimation of pressure gradient lies within the limits of error which can be tolerated. Fig. 1 shows the electrical analog of the flow system we have employed in our studies. The inflow and outflow barriers. Rbl and Rb2, the manometer barriers, Rm1, and Rm2, and the core sample, Rc— for a particular fluid saturation and distribution— are all designated as resistance elements; the flowmeter is designated by an ammeter, A; the pressure source is designated by E; and the manometric device is designated by the voltmeter, V. Included in the circuit are the variable resistances, Rx and Ry, which may be regarded as the leak sinks, and which, in general, can vary in magnitude from zero (i.e., a large hole or shunt in the system) to infinity (i.e., no

Jan 1, 1950

By B. D. Cullity, O. P. Puri

The magnetostrictia of nickel after increasing amounts of plastic elongation was measured at field strengths up to 1500 oe. In addition, the residual stress was measured by means of X-ray line shifts. The observed decrease in magnetostriction following plastic strain is shown to be associated with residual compressive stress. If a metal bar, whose longitudinal axis is taken as the x direction, is plastically elongated in the x direction and then unloaded, X-ray diffraction measurements will indicate the presence of a residual compressive macrostress 0%. However, stress measurement by means of mechanical relaxation does not reveal any macrostress. In a previous paper1 the fictitious macrostress indicated by X-rays was ascribed to a particular distribution of micro-stress, namely, one in which the bulk of the material was stressed more or less uniformly in compression and a very small portion in tension. It was shown that this distribution would account for Neurath's measurements2 of magnetic losses in silicon steel, because of the effect of residual stress on magnetostriction. The present paper is concerned directly with magnetostriction, in nickel, and with the effect on magnetostriction of the residual stress created by plastic elongation. The residual stress was determined by measurements of X-ray line shifts. MATERIAL AND METHODS Commercially pure "A" nickel was investigated. Its nominal composition, in weight percent, is 99.4 Ni + Co, 0.2 Mn, 0.15 Fe, 0.1 Cu, 0.1 C, 0.05 Si, and 0.005 S. Magnetostriction was measured by means of SR-4 electrical-resistance strain gages mounted on specimens 1/4 in. sq and 8 in. long. Magnetic fields up to about 1500 ce were provided by a multilayer, non-cooled solenoid. A considerable amount of heat was developed at the higher field strengths, and, to avoid errors due to changes in the specimen temperature, the following procedure was adopted. Each measurement of the magnetostriction X at a particular field strength H was preceded by demagnetization and an adjustment of the strain indicator to zero; the field H was then quickly switched on and the strain read immediately. Curves of ? vs H were flat for field strengths above about 750 oe for all specimens, and this constant value of X was accordingly taken as the saturation magnetostriction ?s The X-ray measurements of residual stress were made with a Norelco diffractometer on specimens cut from flat bars 1 1/4 in. wide, 1/8 in. thick, and 12 in. long. These measurements were confined to lattice planes parallel to the surface of the specimen. Two reflections were studied: the 311 CrKß line at 28 = 157 deg, and the 420 CuKal line at 28 = 155 deg. The line centers were determined by fitting a parabola to the peak of the line, as suggested by Ogilvie3 and as modified by Koistinen and Marburger.4 The CuKa doublet from the plastically elongated specimens was first resolved by the Rachinger method5. All X-ray measurements were made by counting at fixed angular positions. RESULTS The results of the magnetostriction measurements are shown in Fig. 1 and Table 1. The magnitude of

Jan 1, 1963

By Halbert Powers Gillette

From the known laws of physical chemistry I believe it can be shown that progressive mass movement of water solutions in channels has seldom been the means of ore-concentration in veins. It is my purpose in this paper to show that the force known as "osmosis " has been the principal factor in ore-formation. Convection-currents have doubtless supplemented osmosis, and the two working together have been the agencies that have gathered the scattered particles of rare minerals into the larger masses which are called ore. Osmosis is commonly thought of as a vague, feeble force

Jan 1, 1904

By J. B. Hess, C. S. Barrett

Single crystal rods of cadmium collapse under uniaxial compression into peculiar kinks if the (0001) glide plane is nearly parallel to the axis of compression. In his report first describing this behavior, Orowan1 proposed that these "kink bands" do not develop entirely by ordinary gliding and twinning but by a special mechanism in which glide lamellae of uniform thickness snap abruptly to a tilted position that permits lattice continuity across the glide planes. He concluded that a portion of each boundary of a kink band consists of a plane (non-crystallo-graphic) which bisects the angle between the glide planes on the two sides of it, and along which the bending and the dislocations are concentrated. The data presented by Orowan seemed to us to be insuffcient to conclude that a wholly new mechanism of deformation was responsible for the kinks. Therefore, we have investigated zinc, which is hexagonal close-packed and has an axial ratio near to cadmium, to see whether similar bands are produced, and whether the ordinary mechanisms of glide, bend-gliding, twinning, and the formation of deformation bands can account for its mode of deformation. We find that kinks form profusely in zinc as shown in Fig 1. The structure of these kinks, reported below, seems to require no new mechanism for their explanation, but indicates that kink bands are a special form of deformation bands and develop gradually, solely from basal glide. A theory covering the formation and structure of the bands is presented in detail because it is seldom possible to study deformation bands under such simple conditions, yet many principles applying to these kinks should also apply to deformation bands in general. Experimental Procedures Single crystal rods of 2-3 mm diam and 10-15 cm length were grown by the Brideman technique from swaged wire of Horsehead Special zinc in un-coated pyrex tubes. Orientations of the rods were determined with an optical goniometer after cleaving the rods at liquid air temperature. Crystals of desired orientations were then selected and used as "seeds" to grow additional crystals approximately 4 ft in length from which all specimens were cut. The wires were compressed in two ways: in a simple hydraulic handpress —a "soft" machine—and in a Riehle hydraulic testing machine modified to produce very "stiff" action by the simple expedient of inserting lengths of steel bars at the sides of the zinc crystals between the compression plates. For metallographic examination, the specimens were mounted in sealing wax. Hand polishing was employed, with no grits coarser than No. 1 paper; following the abrasives about 0.025 in. was removed by an etch-polishing reagent.* Final etching to reveal ori-

Jan 1, 1950

By J. Charles Miller

Natural carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxidc. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inorganic rather than an organic source. Areas favorable to development of commercia1 production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of fumaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the producing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the structure. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate. Introduction Carbon dioxide, in liquid and solid form, has found a wide variety of uses other than its primary application in carbonating beverages. It is now used in more than 40 different ways, ranging from cooling or freezing to use in gas or liquid form for mechanical purposes, chemical industry, explosive, fire extinction, and tire manufacturing. Undoubtedly the chief supply of carbon dioxide is obtained from industrial plants or artificial sources and until recently natural deposits of the gas have received little consideration. Few will question the utility and perhaps dependability of artificial sources, which possess the advantage over

Jan 1, 1941

By J. Charles Miller

Natural carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxidc. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inorganic rather than an organic source. Areas favorable to development of commercia1 production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of fumaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the producing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the structure. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate. Introduction Carbon dioxide, in liquid and solid form, has found a wide variety of uses other than its primary application in carbonating beverages. It is now used in more than 40 different ways, ranging from cooling or freezing to use in gas or liquid form for mechanical purposes, chemical industry, explosive, fire extinction, and tire manufacturing. Undoubtedly the chief supply of carbon dioxide is obtained from industrial plants or artificial sources and until recently natural deposits of the gas have received little consideration. Few will question the utility and perhaps dependability of artificial sources, which possess the advantage over

Jan 1, 1941

By J. J. Kramer, G. W. Wiener, K. Foster

The effects of the primary grain size and sheet thickness on the secondary growth rates of grains with (100) surface planes were studied in 3 pct Si-Fe sheets. This secondary grain growth was carried out under conditions in which the {100} plane had the lowest surface free energy. The value of the surface energy difference, between the (100) plane and the random matrix planes was found to he only about 3 pct of the grain boundary energy, indicating that most of the driving force for secondary growth is supplzed by grain boundary energy. A method for obtaining cube texture in 3 pct Si-Fe sheets by a secondary recrystallization process has been reported.' It has been demonstrated that a difference in surface free energy between the (100) plane and other planes is responsible for this growth, where the (100) plane has the lowest surface energy. A semiquantitative relation has been derived for secondary grain growth in sheets where primary grain growth has proceeded until the grains have grown through the sheet and the average grain diameter in the plane of the sheet is from one to two times the sheet thickness. Then, the linear growth rate, G, for the secondary grains can be given by where M is the grain boundary mobility, is the grain boundary free energy, is the average primary grain radius, A is the average difference in surface free energy between the (100) plane and planes of other orientations, t is the sheet thickness, and C is a term first proposed by zener6 which acts as a negative driving force, the effect of inclusions in holding up grain boundary motion. Since the problem of grain growth being discussed is under conditions where the matrix grain size is at least equal to the sheet thickness, the radius r is, of course, a function of the sheet thickness. The term B/r is the grain boundary driving force normally associated with inclusion inhibited or texture inhibited secondary recrystallization. Here, however, the term is modified to account for the fact that growth occurs in thin sheets. The term is the additional driving force available because of the difference in surface free energy. The purpose of the present work has been to evaluate the driving force terms of the growth equation by studying growth rates of (100) secondary grains as a function of sheet thickness and primary grain size. From these data it has been possible to determine the relative values of grain boundary energy, surface energy difference, and the inclusion term, C. EXPERIMENTAL PROCEDURE A 3 pct Si-Fe alloy was melted and cast under a helium atmosphere using electrolytic iron and a pure commercial grade of silicon as raw materials. The alloy was hot and cold rolled to a thickness of 0.6 mm, and samples approximately 5 in. long by 1 1/4 in. wide were cut from the cold-rolled sheets. Four different primary grain sizes were obtained

Jan 1, 1963