Search Documents

By Jamie Deuel

The a ad on Connection" For the purpose of this paper, we will concentrate on the ubquitous radon gas as the principle, low-level radiation effect from uranium tailings piles. Standards are also proposed for gamma radiations but, by most accounts, this is much less of a low level problem than is radon. I am also aware of some just completed research at Oak Ridge National Laboratories that suggest polonium may be a major concern in tailings, but those data are preliminary at this time. What is radon gas? In the first place it is not a gas in the accepted sense in that it has no driving pressure head. It might prove a more convenient description to call it radon vapor. Radon vapor, then, is 7-1/2 times heavier than air. Radiologically, it is an alpha emitter which means it spontaneously gives off high ionizing potential but low penetrating power particles. In fact, the alpha particle has such low penetrating power that this sheet of paper will completely shield a person. The problem, though, is breathing the radon decay products, called radon daughters. If radon daughter products are ingested into the lungs, their alpha emissions may cause cancer. The principle carcinoma associated with breathing radon, or more basically, associated with radiological effects is oat cell car- cinoma of the undifferentiated mall cell type. Radon has a 3.8 day half life which means in less than four days half of its initial radioactivity has decayed away. In less than a month it essentially becomes inert or non-radioactive. The Tailings Situation The NRC, in its April 1979 Generic Environmental Impact Statement

Jan 1, 1983

By A. D. Mutch

IT has long been known that there are wide variations in the thermo-electric potential of pyrite. In the last few years a study of this variation and other properties of pyrite was carried out at the University of Toronto by F. G. Smith on specimens of pyrite from many localities.1-3 As a result of these studies the pyrite geothermometer was developed by Professor Smith. The calibration of the pyrite geothermometer is based on the assumption that "crystals of any one electronically conducting mineral species deposited at a high temperature have a more positive thermo-electric potential than crystals deposited at a low temperature, and the thermo-electric potential varies continuously between any given limits of the temperature of deposition." The cause of the variation was postulated to be crystal discontinuities, such as lineage boundaries. As yet this postulated relationship has not been established as fact. On theoretical grounds it is indicated that the thermo-electric potential of pyrite or any other partial conductor is dependent upon a number of factors as well as the temperature of formation. For this and other reasons there is ground for doubt as to the validity of the relationship postulated above. To date a large number of readings have been made with the pyrite geothermometer which have been recorded in terms of the calibration of the instrument in degrees centigrade. So far most of the pyrite tested by this technique has been in association with gold ore. The values for the temperature of formation obtained in these tests appear to be reasonable and, in relation to geological problems, to vary in the right sense. Determinations on some specimens not in association with gold ore have given readings that appear to be much too high, taking into account the probable maximum temperature of the host rock. To sum up, although many determinations made with the. pyrite geothermometer appear to give reasonable values for the temperature of formation of the pyrite, there are at the same time other readings which seem anomalous. On the basis of an examination of available results of work with the pyrite geothermometer, two problems must be considered: 1-the validity of the calibration of the pyrite geothermometer; and 2-the nature of the distribution of the thermo-electric potentials of pyrite in relation to the specific problems that have been examined. In this paper the academic problem relating to the validity of the calibration of the pyrite geothermometer will not be discussed. Instead, the variations of thermo-electric potential of pyrite in association with gold veins will be discussed with regard to specific examinations. The first of these two examinations deals with the distribution of thermo-electric potentials of pyrite in association with a gold vein and was carried out in the McIntyre Porcupine Mine, Schumacher, Ont., in the summer of 1949 as part of a study with this technique. The second problem deals with variations of thermo-electric potential of pyrite in gold ore specimens from all over the world. The specimens used in this study were part of the private collection of Frank Ebbutt, geologist for Howe Sound Exploration Co. Results of Detailed and Reconnaissance Studies In discussion of the results of determinations made in these two studies the values of thermo-electric potential in millivolts will be used. It will be noted that in some of the diagrams the determinations are recorded in terms of pyrite geothermometer temperatures. Fig. 1 is a calibration chart relating, pyrite geothermometer temperatures and thermo-electric potentials. A full discussion of the technique is given in the original paper by F. G. Smith.' Briefly, the determinations are made by placing two stainless steel probes, one hot and the other cold, against the surface of the pyrite crystal being tested. The thermo-electric potential that is developed is read with a null-point potentiometer that is calibrated in what

Jan 1, 1952

By F. L. Fayers, J. W. Sheldon

It has been a matter of concern to the petroleum industry to determine what effect the capillary term has on saturation profiles, since these profiles determine ultimate economic oil recovery. In their original solution of the non-capillary two-phase flow problem, Buckley and Leverett&apos; showed that solutions of the two-phase flow equations became multiple-valued in saturation. Since it is physically unrealistic for saturation to have more than one value at a given position, Buckley and Leverett resolved this difficulty by introducing a saturation discontinuity or "shock". They evaluated the strength and position of the shock from material balance considerations. Recently Sheldon, Zondek and Cardwell&apos; have demonstrated that the method of characteristics can be used to solve this and related problems. Owing to capillarity it is physically unlikely that saturation shocks occur in an oil reservoir. Buckley and Leverett suggested that the effects of interfacial tensions should be included in the fluid flow equations, if the solutions are to give continuous single-valued saturation distributions. An analogy to this problem is encountered in the theory of wpersonic compressible flow where the introduction of the viscous term eliminates shock behavior. However, the mathematical form of the capillary term in the porous medium fluid flow equations differs from the viscosity term in the Navier-Stokes equation. This paper demons~rates that capillarity does eliminate the triple-valued behavior and indicates the magnitude of capillary and gravity effects on the saturation profile for a variety of systems. DERIVATION OF LAGRANGIAN AND EULERIAN FORMS OF THE DISPLACEMENT EQUATION The equations representing capillary, two-phase flow are given by applying Darcy&apos;s law and a material balance condition for each phase. The familiar Darcy and material balance equations are as follows. ^U*^0......<3, ^^r=°......c« S is the saturation of the water phase, and B the inclination of the porous medium. Pressures in the oil and water phases differ by the capillary pressure associated with the interfacial tensions, P.-P.=pAS)..........(5) where p, is determined experimentally. The porous medium is said to be oil-wet if P, > Po and water-wet if P, < Po. If the fluids are incompressible and the total volumetric flow rate, q, is constant, then v, f v,, = q...........(6) By eliminating P.. /»,, and v, from Eqs. 1, 2, 5 and 6 it follows that It is convenient to normalize the variables in the problem after the manner of Handy and Hadley% so that Eqs. 3 and 7 become where j,, = —, the fractional flow of water; (F, is a capillary pressure normalizing constant.) Substitution of Eq. 9 into Eq. 8 gives In this partial differential equation for an initial value

By Ernest F. Burchard

The Pao deposits of iron ore are in the State of Bolivar, Venezuela, near Upata, about 30 miles south of the Orinoco River and 90 miles east of Ciudad Bolivar. They were discovered 4 or 5 years ago and have not yet been developed to the stage of mining. In March-April, 1929, the writer devoted a week to the examination of these deposits. The maps, drill records and chemical analyses presented herewith were derived from original sources, and the field photographs were made by the writer. The petrographic and metallographic data are from notes by C. S. Ross and M. N. Short, of the U. S. Geological Survey, who have kindly collaborated in these special phases of the study. The Iron Obebodies Topography and Accessibility The deposits are in a region of low mountains representing northern outliers of the Guayanan Highlands. These mountains reach altitudes of 1800 to more than 2000 ft. above sea level, as determined by aneroid barometer. The iron ore is found on mountain crests that reach altitudes of 1915 to 1930 ft., and may be followed down precipitous slopes for 200 • to 300 ft. or more. The greatest vertical range in outcrop is nearly 400 ft., and drilling has indicated that the ore extends to this depth below the surface in one place, at least. The superior hardness of the iron ore accounts for the preservation of the local mountain crests with the intermediate valleys eroded in softer granitic rock. The deposits of iron ore are reached by a private road for automobiles branching northeast from the Ciudad Bolivar-Upata road, a distance of about 12 miles. This road was used in 1928-29 by trucks for transportation of food and camp supplies, gasoline, drilling equipment, etc., but was not suitable for the transportation of iron ore. Between Ciudad Bolivar and the iron-ore area the western two-thirds of the automobile road passes through nearly level, open country known as the savanna, largely used for grazing cattle. About 96 km. (60 miles) east of Ciudad Bolivar at

Jan 1, 1931

By William A. Johnson

The mathematical analysis of diffusion curves in solid metals is carried out ordinarily by analogy with the flow of heat in a continuous medium and no account is taken of the fact that the materials involved are composed of discrete particles that move discrete distances at irregular intervals. It is possible to treat the problem on the basis of simple assumed atomic mechanisms, in which case, because of the small scale of the elementary process compared to the gross effects observed experimentally, the two procedures lead to the same expression for the variation of concentration with distance. Thus, for engineering purposes, the usual methods are quite satisfactory. If, on the other hand, our purpose is to go beyond the mere collection of data, however desirable this may be, it is necessary to recognize and understand the factors that are of fundamental importance. One factor that has not hitherto been considered when dealing with solid metals is the difference in atomic weights of the isotopes of a single metal. While all the atoms of a given element are alike chemically, their weights may vary by a small but significant amount, and atoms of different weights may have different diffusion rates. With gases this variation in isotopic weight produces a change in the rate of diffusion by a factor inversely proportional to the square root of mass. While, except for the lightest gases, this is not a large effect, it is, for example, sufficient to permit a considerable concentration of one isotope at the expense of others. If metals exhibit a similar phenomenon, some modification of the analysis of the diffusion process will be required, since the different isotopes of a given metal will have different probabilities of moving and the heat-flow analogy will contain a fundamental error. This situation cannot be rectified by using a diffusion coefficient based on the average probability of moving, and it can be shown that even when the diffusion coefficient is independent of composition, the diffusion curve will not agree with the simple theory except in the rare cases where only one isotope exists; e.g., gold. If, however, the mass effect in the solid state were no larger than in the gaseous, the errors arising therefrom in the analysis of ordinary diffusion curves would be quite negligible. Nevertheless, our desire to obtain all possible information concerning the details of the diffusion process, and the possibility of diffusion in the solid state as a means for separating isotopes are cogent reasons for undertaking an experimental study to determine whether isotopes of different masses diffuse at different rates. Experimental Procedure If isotopes of different masses diffuse at different rates, the ratio of the concentration of one relative to another will vary with the distance from the diffusion inter-

Jan 1, 1946

By William A. Johnson

The mathematical analysis of diffusion curves in solid metals is carried out ordinarily by analogy with the flow of heat in a continuous medium and no account is taken of the fact that the materials involved are composed of discrete particles that move discrete distances at irregular intervals. It is possible to treat the problem on the basis of simple assumed atomic mechanisms, in which case, because of the small scale of the elementary process compared to the gross effects observed experimentally, the two procedures lead to the same expression for the variation of concentration with distance. Thus, for engineering purposes, the usual methods are quite satisfactory. If, on the other hand, our purpose is to go beyond the mere collection of data, however desirable this may be, it is necessary to recognize and understand the factors that are of fundamental importance. One factor that has not hitherto been considered when dealing with solid metals is the difference in atomic weights of the isotopes of a single metal. While all the atoms of a given element are alike chemically, their weights may vary by a small but significant amount, and atoms of different weights may have different diffusion rates. With gases this variation in isotopic weight produces a change in the rate of diffusion by a factor inversely proportional to the square root of mass. While, except for the lightest gases, this is not a large effect, it is, for example, sufficient to permit a considerable concentration of one isotope at the expense of others. If metals exhibit a similar phenomenon, some modification of the analysis of the diffusion process will be required, since the different isotopes of a given metal will have different probabilities of moving and the heat-flow analogy will contain a fundamental error. This situation cannot be rectified by using a diffusion coefficient based on the average probability of moving, and it can be shown that even when the diffusion coefficient is independent of composition, the diffusion curve will not agree with the simple theory except in the rare cases where only one isotope exists; e.g., gold. If, however, the mass effect in the solid state were no larger than in the gaseous, the errors arising therefrom in the analysis of ordinary diffusion curves would be quite negligible. Nevertheless, our desire to obtain all possible information concerning the details of the diffusion process, and the possibility of diffusion in the solid state as a means for separating isotopes are cogent reasons for undertaking an experimental study to determine whether isotopes of different masses diffuse at different rates. Experimental Procedure If isotopes of different masses diffuse at different rates, the ratio of the concentration of one relative to another will vary with the distance from the diffusion inter-

Jan 1, 1946

By G. Caetani

I. INTRODUCTION. WE owe to the courtesy of Mr. R. M. Raymond, Manager of the El Oro Mining & Railway Co., Ltd., the permission of publishing in this paper the results of a series of experiments and tests made in view of determining the economical limit to which the fine grinding of the ore by tube-mills could be carried on. For the sake of clearness, the following definitions are given of certain terms used in this paper, as well as of the units and screens in the experiments. Slime : In a general way " slime" is that mill-product, of which from 90 to 95 per cent, will pass a 200-mesh screen (0.067 mm. aperture), and which is treated as one class of material in the El Oro cyanide-plants. As a screen-product, slime constitutes all material that *ill pass a 200-mesh, screen. In sizing, the following products are distinguished:- Coarse Sand : That material remaining on a 100-mesh (0.111 mm. aperture) screen. Fine Sand : That passing through. 100-mesh and remaining on a 200-mesh (0.067 mm. aperture) screen. Slime: That passing through 200-mesh. Fines, which pass through 200-mesh and settle in 30 seconds, and silt, which does not settle in 1 minute. Sand-index : The number proportional to its total fineness considered from the economical point of view, as explained on page 93. Absolute extraction : The percentage of values actually brought into solution. Actual extraction: The percentage of values actually brought to the ziuc-boxes. Units : Dollars, U. S. Currency; pounds; and short tons (2,000 lb.). Gold is valued at $20.67, and silver at $0.50 per ounce. Screens : In the sizing-tests the screens used were:¬ Mesh (per 1 in.), . 24 30 40 60 80 100 150 200 250 Aperture (mm.), . 0.740 0.515 0.424 0.250 0.159 0.111 0.090 0.067 0.058 Strengths of solution : Strengths are expressed in the percent- . age of KCN contained, though the sodium cyanide, which is

Jan 1, 1906

By F. E. Crane, J. Downie

The general application of Darcy&apos;s law to natural rocks has already been challenged in the literature.1 The evidence shows that the permeability as calculated from the Darcy equation can be a function of the pressure drop and the salt concentration of the water phase. Most explanations for aberrant behavior involve clays and their properties and have been qualitatively satisfactory.Recently, however, Odeh2 revived the theoretical views of Yuster.3 Since Yuster&apos;s concept implies a fundamental error in using Darcy&apos;s relationship for two-phase flow, and not merely that conditions may limit its use, Odeh&apos;s experimental support arouses considerable interest. However, Odeh&apos;s work as presented is thought to to be inadequate. He has omitted important information about his materials and procedures; therefore, acceptance of his conclusions should be withheld. Since a clay effect is possible, Odeh should have been allowed space to present a more detailed account of the rocks which he used and the precautions which he took to avoid confounding the effects of clay and fluid circulation. In addition, it follows from Odeh&apos;s discussion that the oil relative permeability should increase as the viscosity ratio increases. Odeh presents data corroborating this deduction. It also follows that the oil relative permeability should decrease as the viscosity ratio of oil to water decreases. However, our results show that a high relative permeability, when once attained by using a viscous oil, may be maintained when that oil is replaced by an oil of much lower viscosity. EXPERIMENTAL PROCEDURE The results are shown in Fig. 1 and were obtained as follows. Sandstone cores. 3-in. long X l-in, in diameter and which contained clays, were saturated with

TWO American students entered the École des Mines in 1856, Joseph Lesley of Philadelphia and Thomas Egleston of New York. Lesley remained there only one year, but Egleston completed the whole curriculum and received, in 1860, the certificate given to foreign students in lieu of the official appointment and degree awarded French students. Returning home he received, in 1861, an appointment by Secretary Henry of the Smithsonian Institution to sort, label, and arrange the collections of mineralogical and geological specimens which had been brought to Washington by the various government exploring expeditions in the West. Thomas Egleston, born in New York City on Dec. 9, 1832, was the son of Thomas Jefferson Egleston, who came to New York from Massachusetts some time before 1829. The first American ancestor of the family had settled near Dorchester in 1630. T. J. Egleston and Joseph Battell established an iron-merchandizing business* at 166 South St., New York, which prospered exceedingly; so much so that when Thomas J. Egleston died, July. 12, 1861, his estate had a book value of over $500,000. Since an older brother was expected eventually to take over this business, Thomas, who had a liking for science, went to Yale, where he completed the regular four-year course in 1854, and then remained another year for advanced work in chemistry under Silliman. One biographer says he went to Europe, early in 1856, on account of his health. It was the custom at that time for wealthy young men to make a tour of Europe after completing their academic education. Whatever the precise reason, he began scientific work at the Jardin des Plantes in Paris but soon trans-

Jan 1, 1941

By Frank Firmstone

IN 1871, two furnaces at the Glendon Iron Works, which had been blown out on account of the "coal strike," were altered from the open-top plan with side flues for collecting the gas, to closed tops with cup and cone. In one furnace the suppression of the side flues permitted a considerable alteration in the profile, but in the other (No. 5) no change in this respect was made; the side flues were simply bricked up and new ones cut through the sides close to the top. This furnace was in blast over four years, and we can, therefore, form a pretty good idea of the effect of the alterations on the furnace process. The principal dimensions are; Height 72&apos;; greatest diameter, 18&apos;; diameter at tuyeres, 8&apos;; diameter of top, 10&apos;; diameter at stock line (point at which the top of the materials is kept), 11&apos;; cubic contents, 11,900 cubic feet. The table below shows the average results for periods of twenty-six weeks each. 1st, of the open-topped furnace; 2d, of the furnace with the first charger used, which was an ordinary cup and cone (diameter of cone 5&apos; 2") 3d, with the charger used ever since, a "double" cone 7&apos; 5" diameter outside, having a central opening 3&apos; in diameter. The diagram (Plate II) shows the daily variations, in the grade of the irons for the same periods.* * In calculating the average grade of each day&apos;s iron, each twelve hours was taken by itself whenever more than two kinds of iron were made in the 24 hours, and the diagram drawn accordingly. By counting, it will be found that there were more such days with the single cone than with the "double" cone, and more with this than with the open top. † Anthracite.

Jan 1, 1876

By E. H. Kelton, R. D. Grissinger

E. E. Schumacher.*—DO YOU control the humidity in your test room? What effect does the environment have on your results? E. H. Kelton.—We do not attempt to control the humidity. As a matter of fact, the humidity in the beam tests that were conducted in a constant-temperature room varied widely and, as far as we know, there is no effect. The tension tests were conducted largely in an oil bath. I suppose there would be an effect in highly corrosive atmospheres, sufficiently corrosive to notch the specimen; otherwise, I would say none. E. A. Anderson.*—The effect of the humidity on the corrosion of zinc does not become important until the relative humidity is 70 per cent. At that point the corrosion products are capable of absorbing moisture and the corrosion rate increases. Below that point corrosion is almost imperceptible. This does not take into account any effect due to stress. That may be important. E. E. Schumacher.—Recently 1 have become very conscious of the enormous effect that surface films can exert on the physical properties of certain alloys. Shortly, we are publishing an article in which it will be shown that the fatigue endurance of some lead alloys can be changed markedly by merely changing the type of film placed on their surfaces. Changes as great as tenfold were observed. These findings make me wonder whether in your creep test you might not obtain quite variable results, depending upon the type of liquid medium used to immerse your specimens. Did you use more than one type of oil and, if you did, what were your results? E. H. Kelton.—I think we have used no more than three different oils, and we could not see any difference in effect.

Jan 1, 1945

By Erwin S. Sperry

Some time ago, the author had occasion to make an alloy of equal parts of nickel and aluminum, for the purpose of adding small amounts of nickel to pure aluminum. The nickel was melted in a plumbago crucible under a layer of borax ; and at a proper temperature the aluminum was added, and the whole mass was stirred with a plumbago stirrer. The alloy immediately became incandescent and boiled. It was then poured into iron moulds, in the form of ingots weighing about 10 pounds. The metal when poured was very fluid and free from the viscosity so often noticed in nickel and nickel-alloys. The color of the alloy is gray, not unlike that of wrought-iron, and the fracture is devoid of any crystalline appearance. It is quite brittle, and can be readily ground to a powder in a mortar. More metal was made than was needed; and what remained unused was placed in a covered wooden box and set away. In about three months, as it mas again necessary to use the alloy, the box was opened; and, much to my surprise, nothing but a dark gray powder was found in it. This condition of the alloy could not be accounted for. An attempt was made to melt the powder and pour it again into ingots, but with negative results. Analogy pointed to disintegration; and it was decided to make a fresh sample of the alloy, and watch the material from the beginning. In the second experiment the conditions were identical with those of the first, with the exception that fluor spar was substituted for the borax. This change was made because it was thought that perhaps the borax might have been

Jan 1, 1900

By D. Weinstein

Yieldilzg in annealed arc-cast molybdenunz in torsion was studied as a function of strain rate and tem-perature. The temperature dependence of the yield point for different strain rates was used to calculate a heat of activation for the yield point. The heat of activation was not a constant but was approximately a linear function of the stress at yield. It is proposed that the rate effect in yielding is determined in part by a site place-change of C (or other interstitial atom) in the metal. THE low-temperature embrittlement phenomenon in metals and alloys has been known to exist for a long time. Although a transition from ductile to brit-tle behavior has been observed in some close-packed hexagonal metals1 and a face-centered cubic alloy, the most common class of metals exhibiting this be-havior has a body-centered cubic lattice structure. For example, a ductile to brittle transition has been observed in iron,3 molybdenum,4 chromium,5 colum-bium,6 and tungsten.7 In the present investigation, molybdenum specimens were tested in torsion over a wide range of temperatures at three widely separated strain rates, and the temperature for onset of embrittlement was determined. Characteristic of body-centered cubic metals and closely associated with plastic deformation is the appearance of a sharp upper and lower yield point. Theoretical explanation of the yield point in iron and low-carbon steel is due to Cottrell,8 who attributes the phenomenon to the pinning of dislocations by the formation of impurity atmospheres around the dislocations. These atmospheres tend to lock the dislocations and make them more difficult to move. The stress required to move a dislocation and thereby cause plastic deformation is greatly increased, and thus an upper yield point is observed. In addition, theoretical analysis,9 as well as experimental observations, show that the upper yield point is strongly a function of temperature. The upper yield point is observed to decrease with an increase in testing temperature, and above a certain temperature (-700° K in iron) it no longer appears. This is consistent with the concept that thermal vibrations will help free a dislocation from its atmosphere, so that the external stress required to free a dislocation from its pinning atmosphere decreases with increasing temperature. Furthermore, with increasing temperature the equilibrium concentration of impurity atoms around a dislocation decreases exponentially with the result that the dislocation is less firmly pinned. In Cottrell&apos;s theory of yield point a static model is visualized in which the pinning atmospheres, particularly interstitial atoms, are immobile, and the dislocations are anchored to stationary positions in the lattice. However, experiments1,7 show the upper yield point to be time-dependent or a function of the rate of straining, a high strain rate causing a high upper yield point. Present theory does not adequately account for the rate dependence of the yield point, and the exact function of the interstitial atom is not under stood. Nevertheless, observation of the temperature dependence and rate dependence strongly suggests that the upper yield point phenomenon is due to the interaction between dislocations and pinning atoms, and that a diffusion mechanism is important in determining the yield point.

Jan 1, 1962

By A. D. Mutch

IT has long been known that there are wide variations in the thermo-electric potential of pyrite. In the last few years a study of this variation and other properties of pyrite was carried out at the University of Toronto by F. G. Smith on specimens of pyrite from many loyalities. As a result of these studies the pyrite geothermometer was developed by Professor Smith. The calibration of the pyrite geothermometer is based on the assumption that "crystals of any one electronically conducting mineral species deposited at a high temperature have a more positive thermoelectric potential than crystals deposited at a low temperature, and the thermo-electric potential varies continuously between any given limits of the temperature of deposition." The cause of the variation was postulated to be crystal discontinuities, such as lineage boundaries. As yet this postulated relationship has not been established as fact. On theoretical grounds it is indicated that the thermo-electric potential of pyrite or any other partial conductor is dependent upon a number of factors as well as the temperature of formation. For this and other reasons there is ground for doubt as to the validity of the relationship postulated above. To date a large number of readings have been made with the pyrite geothermometer which have been recorded in terms of the calibration of the instrument in degrees centigrade. So far most of the pyrite tested by this technique has been in association with gold ore. The values for the temperature of formation obtained in these tests appear to be reasonable and, in relation to geological problems, to vary in the right sense. Determinations on some specimens not in association with gold ore have given readings that appear to be much too high, taking into account the probable maximum temperature of the host rock. To sum up, although many determinations made with the pyrite geothermometer appear to give reasonable values for the temperature of formation of the pyrite, there are at the same time other readings which seem anomalous. On the basis of an examination of available results of work with the pyrite geothermometer, two problems must be considered: 1—the validity of the calibration of the pyrite geothermometer; and 2— the nature of the distribution of the thermo-electric potentials of pyrite in relation to the specific problems that have been examined. In this paper the academic problem relating to the validity of the calibration of the pyrite geothermometer will not be discussed. Instead, the variations of thermo-electric potential of pyrite in association with gold veins will be discussed with regard to specific examinations. The first of these two examinations deals with the distribution of thermo-electric potentials of pyrite in association with a gold vein and was carried out in the McIntyre Porcupine Mine, Schumacher, Ont., in the summer of 1949 as part of a study with this technique. The second problem deals with variations of thermo-electric potential of pyrite in gold ore specimens from all over the world. The specimens used in this study were part of the private collection of Frank Ebbutt, geologist for Howe Sound Exploration Co. Results of Detailed and Reconnaissance Studies In discussion of the results of determinations made in these two studies the values of thermo-electric potential in millivolts will be used. It will be noted that in some of the diagrams the determinations are recorded in terms of pyrite geothermometer temperatures. Fig. 1 is a calibration chart relating pyrite geothermometer temperatures and thermoelectric potentials. A full discussion of the technique is given in the original paper by F. G. Smith.&apos; Briefly, the determinations are made by placing two stainless steel probes, one hot and the other cold, against the surface of the pyrite crystal being tested. The thermoelectric potential that is developed is read with a null-point potentiometer that is calibrated in what

Jan 1, 1953

By A. D. Mutch

IT has long been known that there are wide variations in the thermo-electric potential of pyrite. In the last few years a study of this variation and other properties of pyrite was carried out at the University of Toronto by F. G. Smith on specimens of pyrite from many loyalities. As a result of these studies the pyrite geothermometer was developed by Professor Smith. The calibration of the pyrite geothermometer is based on the assumption that "crystals of any one electronically conducting mineral species deposited at a high temperature have a more positive thermoelectric potential than crystals deposited at a low temperature, and the thermo-electric potential varies continuously between any given limits of the temperature of deposition." The cause of the variation was postulated to be crystal discontinuities, such as lineage boundaries. As yet this postulated relationship has not been established as fact. On theoretical grounds it is indicated that the thermo-electric potential of pyrite or any other partial conductor is dependent upon a number of factors as well as the temperature of formation. For this and other reasons there is ground for doubt as to the validity of the relationship postulated above. To date a large number of readings have been made with the pyrite geothermometer which have been recorded in terms of the calibration of the instrument in degrees centigrade. So far most of the pyrite tested by this technique has been in association with gold ore. The values for the temperature of formation obtained in these tests appear to be reasonable and, in relation to geological problems, to vary in the right sense. Determinations on some specimens not in association with gold ore have given readings that appear to be much too high, taking into account the probable maximum temperature of the host rock. To sum up, although many determinations made with the pyrite geothermometer appear to give reasonable values for the temperature of formation of the pyrite, there are at the same time other readings which seem anomalous. On the basis of an examination of available results of work with the pyrite geothermometer, two problems must be considered: 1—the validity of the calibration of the pyrite geothermometer; and 2— the nature of the distribution of the thermo-electric potentials of pyrite in relation to the specific problems that have been examined. In this paper the academic problem relating to the validity of the calibration of the pyrite geothermometer will not be discussed. Instead, the variations of thermo-electric potential of pyrite in association with gold veins will be discussed with regard to specific examinations. The first of these two examinations deals with the distribution of thermo-electric potentials of pyrite in association with a gold vein and was carried out in the McIntyre Porcupine Mine, Schumacher, Ont., in the summer of 1949 as part of a study with this technique. The second problem deals with variations of thermo-electric potential of pyrite in gold ore specimens from all over the world. The specimens used in this study were part of the private collection of Frank Ebbutt, geologist for Howe Sound Exploration Co. Results of Detailed and Reconnaissance Studies In discussion of the results of determinations made in these two studies the values of thermo-electric potential in millivolts will be used. It will be noted that in some of the diagrams the determinations are recorded in terms of pyrite geothermometer temperatures. Fig. 1 is a calibration chart relating pyrite geothermometer temperatures and thermoelectric potentials. A full discussion of the technique is given in the original paper by F. G. Smith.&apos; Briefly, the determinations are made by placing two stainless steel probes, one hot and the other cold, against the surface of the pyrite crystal being tested. The thermoelectric potential that is developed is read with a null-point potentiometer that is calibrated in what

Jan 1, 1953

By Frank H. Reed, P. W. Henline, Harold W. Jackman

A sumMary of the consumption of coal in 1945 shows that the coke industry ac-counted for 17 pct of the total coal used. No substitute for coke and the blast furnace in the reduction of iron ore has gained sufficient prominence so far to be given serious consideration. However, while the same slot-type ovens are being built and used now as were in use a few years ago, the problem of obtaining suitable coking coals, both high- and low-volatile, has forced many operators to revamp coal-blending facilities. Until the beginning of World War 11, high-temperature ooke plants were able to secure the required high-volatile and low-volatile coals from two or three seams and from three or four mines. Thus, many of our coke oven plants were able to operate with storage bins for two coals only. The vari-pnce in raw materials was not great, and uniformity of blend was a relatively simple problem. Since the beginning of World War 11, many and important changes have taken place. Demand for all coals increased greatly. Production, though kept as near maximum capacity as possible, could not meet the demands for coal generally, and particularly for the various kinds of coal which have proved to be satisfactory for specialized uses; coals were allocated as nearly as possible in the order of greatest need; storage piling was reduced to the minimum necessary to keep plants in operation; uniformity of quality could not be maintained, and with this last, uniformity of composition of blends for coking could not be maintained. Whereas before the war producers of metallurgical coke could fill their needs from three or four mines, by the end of the war it was not unusual to find shipments to a single coke oven plant coming from as many as 30 different mines, in a single month. Since many of the mines producing both high- and low-volatile coal for high-grade metallurgical coke are rapidly nearing de-pletion, the problem of seeking new sources and of blending a number of coals in each plant for the production of high-temperature coke is facing practically every producer in the United States at the present time, and is one which will probably continue for many years to come. Midwestern byproduct coke ovens in the Chicago and St. Louis areas use annually from 12 to 15 million tons of bituminous coals which are transported 500 to 700 miles from the Appalachian coal fields of Pennsylvania, West Virginia, and eastern Kentucky. Approximately two-thirds of this coal is high-volatile bituminous. The critical transportation problem confronting the nation in 1943, and the growing scarcity of the best Appalachian coking coals, prompted the Illinois Geological Survey to propose a research program in which would be studied the coking properties of blends of low-sulphur, high-volatile Illinois coal with the high- and low-volatile coals from the eastern fields. Such blends containing Illinois coal, if substituted for the all-eastern blends normally coked,

Jan 1, 1949

By W. Geo. Waring

Introduction THE winning of zinc and lead ores from the comparatively shallow deposits of the Joplin district, presents, few such problems for the mining engineer as are encountered in deep ore mining and in the handling of complex ores. However, for those who are interested in the origin and nature of ore deposits in general, there is much here to investigate, and upon studies in this direction will depend in no small measure the future of an industry that has produced during the year 1916, in southwest Missouri, lead and zinc ores to the value of $26,319,383; adding $46,022,164 to the metallic wealth of the nation. Including the adjacent mines in Ottawa County, Oklahoma, and Cherokee County, Kansas, which are, really continuations of the Joplin district, the total value of ores produced reached the sums of $34,089,503, and that of the metals, $58,927,941.1 The ores produced in the Joplin district are remarkable on account of their almost uniformly high" metal content in both lead and zinc. Their superiority in this regard is unparalleled, and is doubtless clue to certain geological conditions that are now possibly explicable, provided that the artesian circulation = ascension hypothesis of the origin of the ore deposits is proven beyond question to be the only tenable explanation of the facts. These, as well as other valuable zinc-ore deposits, are bound to he exhausted in time, for ordinary mining purposes, acid it concerns the mining engineer that the conditions under which ores of this character were actually deposited in the form in which they occur, may, if possible, be ascertained, in order that he may learn where to look for similar deposits in other regions, or even how to reproduce artificially such condi-

Jan 9, 1917

Discussion of the paper of C. A. HEBERLEIN, presented at the New York meeting. February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 497 to 504. H. D. PALLISTER, State College, Pa. (communication to the Secretary).-Mr. Heberlein gives some valuable information concerning a branch of mining and metallurgy which has been neglected during the last few years. His results with fine grinding and Deister tables suggest the possibility of the mining and concentration of a number of low-grade cinnabar deposits. Can Mr. Heberlein give us some idea as to the loss of quicksilver during this concentration? The advances in the metallurgy of quicksilver have been few and far between in recent years. Most miners prefer to go on in the old way with the Scott furnace and the large brick condensers. The large brick condensers are expensive to build and to keep in repair, and on account of the thick walls are extremely slow in cooling the gases; and further, the joints between the bricks offer passages for the quicksilver vapors unless great care is used in building the condensers.. The escape of vapor at the top of the furnace is another source of loss and I see the people at the Oceanic mine have overcome this in a very ingenious way. I recently returned from the Terlingua quicksilver district of Texas, where the only operating company, the Chisos Mining Co., is operating a 20-ton furnace of the Scott type. They had considerable difficulty with getting a good extraction, clue to too high heating in the furnace with its .resulting diffIculties. Recently they have been running with ashpit and fire doors closed and have been able to keep the heat lower, thus getting much better results and practically verifying the results obtained at the Oceanic mine.

Jan 5, 1915

By Simon H. Ash

The coal-mining districts of Washington are mainly west of the Cascade Mountains; Fig. 1. The mines are on the foot hills of the slope, the lignite fields of Lewis and Thurston counties extending into the valleys west of the mountains. An exception is the Roslyn field, a small but important area on the eastern slope. If western Washington is divided into three areas from north to south, the bituminous coal fields and most of the active operations will be found largely in the middle area. The southern portion contains lignites over a large area. In the northern portion, mining is practically restricted to one mine, the Bellingham, which is working a subbituminous coal seam near the city of Bellingham. The degree of alteration that the coal of a particular field has undergone may be gaged roughly by the position of the field with reference to the Cascade Mountains. The lignites of Tenino, Tono, Mendota, and Castle Rock, on the railway line connecting Seattle and Portland, occur in a region of low relief, in which the Eocene coal measures have suffered only minor disturbances. Subbituminous coals occur in the foot hills, as at Renton, Newcastle, and Bellingham. Coalg high in fixed carbon are found nearer the mountains, where the measures have been sharply tilted and folded, as at Black Diamond and Carbonado. The two typical anthracite fields are located still higher, in the rugged mountains where outcrops appear both in deep gorges and on ridges at elevations approaching 5000 ft. At Carbonado is found the only semianthracitc seam worked on a commercial basis. The occurrence of this seam in a region of bituminous coal is due to the nearness of an igneous sill, which has changed its character from bituminous to semianthracite. Purpose of Paper On account of the various faults and dips and the varying nature of the wall rock, many difficulties are encountered in mining and winning the coal. The paper gives some of the methods used in mining and, in some detail, the conditions that affect the efficiency of these methods.

Jan 1, 1925

By John B. Goddard, David R. Brosnahan

Leaching of uranium in situ from sandstone deposits with ammonium carbonate solution containing dissolved oxygen occurs rapidly compared with the leaching of the bulk of the sulfur present as FeS2. However, because of their high reducing capacity and their relative abundance, the FeS2 minerals consume the bulk of the oxidant. A pressure leach apparatus was constructed that permitted measuring oxygen consumption by FeS2, best described by a first-order reaction. The experimental rate constants for various cores are roughly proportional to their FeS2 contents.

Jan 1, 1983