Search Documents

By C. E. Birchenall, R. H. Condit

THREE surface activity procedures are in com--L mon use for the determination of diffusion coefficients in solids. In the oldest of these' the activity observed at the original surface is compared before and after diffusion, where all the activity is in a thin, plated layer on the surface before diffusion. Partial absorption of the radiations from active atoms which have diffused below the surface reduces the effective activity after diffusion. The formula employed to calculate the diffusion coefficient is where F, is the ratio of final to initial activity at the surface, measured with identical counting geometry; Z=u3Dt, where D is the diffusion coefficient; t is the diffusion time; and u is the absorption coefficient for the radiation in the solid as defined by Lambert's law. This absorption law implies that all the rays are parallel to each other and normal to the specimen surface. This assumption of a collimated beam used by Steigman, Shockley, and Nix has been adopted by all other investigators and, although it gives results which are approximately correct under restricted physical conditions, it does not represent many actual circumstances. It is the purpose of this paper to show the importance of the divergent rays and to indicate a procedure for taking them into account. In the residual activity method the activity is determined on a series of surfaces ground on the specimen at progressively greater depths in the diffusion layer parallel to the initial surface. Gruzin2 has de- rived a formula for this procedure, which may be put in the form where I is the ratio of the activity measured at a newly ground surface at distance k below the initial surface to the activity at the initial surface measured after diffusion, and K= k/2p Dt. A third procedure involves the autoradio-graphic determination of activity on a plane ground at a small angle to the initial interface through the penetration zone. Aut oradiography can be particularly sensitive to the oblique rays. Unlike most counters which detect essentially all ß particles or X-rays which enter the active volume as a single event, the photographic emulsion may be thin enough so that oblique rays with longer path length in the emulsion produce more darkening than rays which move normal to the film plane. Consider a plane containing a source of radiation uniformly spread over a circle and a point counter located on the perpendicular through the center of the circle. As the counter moves along this line, the total angle 6, at the counter subtended by the specimen will vary. For a fixed counter distance, let 6 be angle between the counter axis and the line connecting the counter to a point P on the active plane. If an absorber of thickness X is interposed parallel to the source between counter and source, the ray from point P to the counter will pass through an absorber thickness X secant 6. Exponential absorption is assumed to hold for all rays. If r, is the ratio of intensity at the counter with absorber to the intensity without absorber and a = pX, 1 00 The behavior of this integral, evaluated numerically,

Jan 1, 1957

By Eldred D. Wilson

Apropos of metals low in the series illustrated by Dr. Butler's Table II, it is interesting to note that Cress and Feldman reported traces of platinum metals in several samples of alunite. They found, chemically and spectrographically, several traces of platinum, palladium, and rhodium in alunite from Sugar Loaf Peak, near Quartzite, Ariz.; silver, platinum, and rhodium in alunite from Rio Grande County, Colorado; and traces of rubidium and gallium in various samples of alunite. These authors stated that the platinum metals appear to be present as oxides and suggested deposition by hydrothermal solutions under near-surface conditions.

Dec 1, 1956

By J. L. Shafer, Christopher L. Caenepeel, Martha L. White

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper. Modelling of the Leaching Process During the past 10 years the activity in the mathematical modelling of the leaching of copper sulfides in copper dumps and heaps has increased dramatically. The modelling of copper oxide leaching has not received as much attention. The acid leaching of non-sulfide copper minerals while chemically less complex, compared to sulfides, does generate a vertical acid concentration gradient in the ore heap being leached due to the acid-base nature of the reaction. This is generally not observed in sulfide deposits that are biologically active, due to the buffering action of opposing reactions involving the generation of sulfuric acid from sulfide minerals and acid consuming host rock. Thus, the objective of ORC 's copper oxide modelling efforts is to determine the leaching parameters which will account for this vertical acid concentration gradient. Knowledge of this gradient will result in the correct choice of the feed acid concentration to the top of the ore dump or heap, such that the effluent will have the desired pH.

Jan 1, 1980

By A. F. Lucas

Introduction BELLE ISLE, located in the low sea marshes near Atchafalaya Bay, is the southeasternmost of the famous Five Salt Islands of Louisiana. Rising about 80 ft. (24 m.) above the level of the surrounding marsh and being some 800 acres (323 ha.) in extent, it constitutes a striking landmark on the low Gulf coast, and since the eighteenth century, when it played an important part in the operation of the buccaneers, it has been intermittently frequented by man. In 1897, the writer discovered the great mass of salt that underlies the island and shortly afterward pub-lished a brief account of the geology of Belle Isle and the neighboring salt islands.' In that paper he described principally the salt, but pointed out also the occurrence of petroleum and of sulphur in the strata above the salt. Since that time the island has been extensively explored by the drill, and the developments up to 1908 have been described by Veatch2 and Harris," and Knapp.4 The writer's early conclusions as to the probable presence of sulphur in considerable quantity have been confirmed by the later drilling, some of the wells having found quantities of gas containing sulphur dioxide and a number of sulphur-bearing strata as well. Under the stimulus of the present keen demand for sulphur for war purposes, a syndicate of New York capitalists was recently formed to explore the sulphur resources of the island in more detail. Under the writer's direction, six wells were drilled for this syndicate during the winter of 1916-17. The present paper presents briefly the results of this work and sums up the present knowledge of the geology of this highly interesting locality.

Jan 9, 1917

By W. H. Meyer

During the seventeen years Fairchild has been making aerial surveys and aerial photographic equipment many changes and improvements have been made in the equipment and in the technique of using it. Aerial photographic operations have been developed from the crude methods and apparatus of wartime to a science upon which exact engineering calculations can be based. In the early days there was no airplane specially designed to meet aerial photographic requirements. One type of camera was used in all types of operations. Projects were made to conform to the products we could make and deliver. Obviously this entailed definite limitations. We now have airplanes designed specially for aerial photographic operations in accordance with the conditions encountered in actual service experience. We have cameras for every photographic purpose and our laboratory technique and equipment have been developed to the point where it is possible to make contour maps from vertical aerial photographs with contour intervals as close as five feet. Therefore, the selection of equipment now can be made in accordance with the time at our disposal, the justifiable cost, the scale desired, and the general requirements of the client. This does not mean, however, that arbitrary deliveries can be set for aerial photographic products. The factors in each project vary and each job must be considered in accordance with the factors involved. This accounts for the fact that products of aerial surveys may readily vary from $1.25 to $200 a square mile. Sherman M. Fairchild became interested in the design of a radically different aerial camera during the war. At its close he was about ready to demonstrate his design to the War Department. By 1920, he was able to bring out his first completed model. It had a number of radical features, one of which was the first dependable high-speed between-the-lens shutter, which makes for accuracy in aerial photographic work. Another feature was the use of metal throughout, eliminating the wooden parts that had been employed in wartime cameras. Another feature was the interchangeability of parts.

Jan 1, 1937

By William Meyer

DURING the seventeen years Fairchild has been making aerial surveys and aerial photographic equipment many changes and improvements have been made in the equipment and in the technique of using it. Aerial photographic operations have, been developed from the crude methods and apparatus of wartime to a science upon which exact engineer-ing calculations can be based. In the early days there was no airplane specially designed to meet aerial photographic requirements. One type of camera was used in all types of operations. Projects were made to conform to the products we could make and deliver. Obviously this entailed definite limitations. We now have airplanes designed specially for aerial photographic operations in accordance with the conditions encountered in actual service experience. We have cameras for every photographic purpose and our laboratory technique and equipment have been developed to the point where it is possible to make contour maps from vertical aerial photographs with contour intervals as close as five feet. Therefore, the selection of equipment now can be made in accordance with the time at our disposal, the justifiable cost, the scale desired, and the general requirements of the client. This does not mean, however, that arbitrary deliveries can be set for aerial photographic products. The factors in each project vary and each job must be considered in accordance with the factors involved. This accounts for the fact that products of aerial surveys may readily vary from $1.25 to $200 a square mile. Sherman M. Fairchild became interested in the design of a radically different aerial camera during the war. At its close he was about ready to demonstrate his design to the War Department. By 1920, he was able to bring out his first completed model. It had a number of radical features, one of which was the first dependable high-speed between-the-lens shutter, which makes for accuracy in aerial photographic work. Another feature was the use of metal throughout, eliminating the wooden parts that had been employed in wartime cameras. Another feature was the interchangeability of parts.

Jan 1, 1936

By Frederic Laist

IN the spring of 1931 an experiment was made at Anaconda with a small reverberatory furnace, with which was combined a roasting shaft. The arrangement is shown in the accompanying drawing (Fig. 1) and requires but little explanation. The general idea was to roast .flotation concentrates, mixed with the proper fluxing materials, by dropping them down a heated shaft, from which the calcines would enter the smelting zone of the reverberatory furnace through an opening in the roof. The hearth of the reverberatory was 3 ft. wide by 21 ft. long. The roasting shaft was 3 ft. square inside and had an effective height of about 20 ft. . The reverberatory furnace was arranged so that it could be charged either directly through the roof with regular hot calcines, in the usual manner, or by means of the shaft, at the top of which were a feed-ing arrangement by which cold flotation concentrates, suitably fluxed, could be fed continuously and a pipe through which cold air was blown in. Means were provided for distributing the feed over the cross-section of the roasting shaft. At first a mechanical arrangement was used but later it was found that a simple cone served the purpose equally well and gave less operating trouble. On account of the small size of the equipment, it was realized that absolute capacity and fuel consumption figures would mean but little. It was not to be expected that ratios comparable to those obtained in large furnaces could be gotten, and the only way in which any idea could be obtained as to the possibilities of the combination furnace was to run it in parallel with the reverberatory furnace charged in the usual manner and operating without the shaft. The results of such parallel runs are given in Table 1. The amount of oil burned in the reverberatory was purposely maintained at substantially the same rate during both runs in order that the benefits resulting from the shaft might be gaged.

Jan 1, 1933

By Randolph C. Specht

A two year study was made of the waste disposal of the pebble rock phosphate industry. Solid slimes are impounded in large settling areas and the process water is re-used. Clear effluent was not found to be toxic to fish or animal life in field tests or in controlled experiments. Survey: The pebble rock phosphate mining and washing operations in Florida (fig. 1) are along the river basins of the Alafia to the west and the Peace to the east. The elevation of the area varies between 40 and 170 ft above sea level. Effluents from the operations find their way into one of the two river systems (fig. 2), the Peace River which flows into Charlotte Harbor and the Alafia into Tampa Bay, both along the Gulf of Mexico. There are no major industries along these rivers below the phosphate operations. On the Peace River, the town of Arcadia, approximately 50 miles below the phosphate operations, obtains its water from the river. No other communities along the rivers use them as a source of water supply. Small communities, farms, and ranches are located along the rivers and both rivers drain vast swamp areas. Complaints had been received at the office of the Chief Sanitary Engineer, of the Florida State Board of Health,' that both rivers were turbid at various times and that fishing in the Alafia River was "not as good as it used to be." Tests made by another agency on the dissolved oxygen content of the Alafia River revealed that the oxygen content, at times, was comparatively low.= However, it was not shown that the phosphate wastes had any effect upon the oxygen content of the stream. The river waters are normally brown in color due to drainage from vast swamp areas and are very shallow, from 2 to 6 ft in depth. Turbid waters have been noted in streams coming from the present phosphate operations and also from streams along which there are no operations at the present time. It was learned from "old timers" that, when many more companies than at present were operating along both the Alafia and Peace Rivers forty or fifty years ago, no attention was paid to prohibiting the disposal of slimes along the river basins. During dry periods now in some of the river swamps where drainage ditches have been dug, it is indicated clearly that phosphate slimes were disposed of directly into the river swamps for many years past. Places have been observed where there were alternating strata of phosphate mud, leaf mold, and quartz sand. The former practice of indiscriminate disposal of wastes accounts for some turbidity, particularly after heavy rains and washouts and during clearing of land and digging of drainage ditches. During a six months' period in which a large tract of land was being cleared and drainage ditches dug, a small stream (Six Mile Creek), which previously had been clear, showed a turbidity of 600 ppm and remained turbid until the clearing was completed; after which the stream again flowed clear. An interview with the operator of the municipal water plant, which is about 50 miles below the phosphate operations on the Peace River and which used this river as a source of supply, revealed that there had been no taste in the water for the past ten years, other than that occasionally encountered from increased growth of algae. The operations of each of the cooperating com-

Jan 1, 1951

By Randolph C. Specht

A two year study was made of the waste disposal of the pebble rock phosphate industry. Solid slimes are impounded in large settling areas and the process water is re-used. Clear effluent was not found to be toxic to fish or animal life in field tests or in controlled experiments. Survey: The pebble rock phosphate mining and washing operations in Florida (fig. 1) are along the river basins of the Alafia to the west and the Peace to the east. The elevation of the area varies between 40 and 170 ft above sea level. Effluents from the operations find their way into one of the two river systems (fig. 2), the Peace River which flows into Charlotte Harbor and the Alafia into Tampa Bay, both along the Gulf of Mexico. There are no major industries along these rivers below the phosphate operations. On the Peace River, the town of Arcadia, approximately 50 miles below the phosphate operations, obtains its water from the river. No other communities along the rivers use them as a source of water supply. Small communities, farms, and ranches are located along the rivers and both rivers drain vast swamp areas. Complaints had been received at the office of the Chief Sanitary Engineer, of the Florida State Board of Health,' that both rivers were turbid at various times and that fishing in the Alafia River was "not as good as it used to be." Tests made by another agency on the dissolved oxygen content of the Alafia River revealed that the oxygen content, at times, was comparatively low.= However, it was not shown that the phosphate wastes had any effect upon the oxygen content of the stream. The river waters are normally brown in color due to drainage from vast swamp areas and are very shallow, from 2 to 6 ft in depth. Turbid waters have been noted in streams coming from the present phosphate operations and also from streams along which there are no operations at the present time. It was learned from "old timers" that, when many more companies than at present were operating along both the Alafia and Peace Rivers forty or fifty years ago, no attention was paid to prohibiting the disposal of slimes along the river basins. During dry periods now in some of the river swamps where drainage ditches have been dug, it is indicated clearly that phosphate slimes were disposed of directly into the river swamps for many years past. Places have been observed where there were alternating strata of phosphate mud, leaf mold, and quartz sand. The former practice of indiscriminate disposal of wastes accounts for some turbidity, particularly after heavy rains and washouts and during clearing of land and digging of drainage ditches. During a six months' period in which a large tract of land was being cleared and drainage ditches dug, a small stream (Six Mile Creek), which previously had been clear, showed a turbidity of 600 ppm and remained turbid until the clearing was completed; after which the stream again flowed clear. An interview with the operator of the municipal water plant, which is about 50 miles below the phosphate operations on the Peace River and which used this river as a source of supply, revealed that there had been no taste in the water for the past ten years, other than that occasionally encountered from increased growth of algae. The operations of each of the cooperating com-

Jan 1, 1951

THE record of the development of physical metallurgy since the founding of this Institute embraces by far the greater part of physical metallurgy as this subject is recognized today. Yet it is not to be supposed that the metallurgist interested in the properties and behavior of solid metals at the beginning of this period was without important and even fundamental information. He had an empirical knowledge of the behavior of solid metals which extended backward into prehistoric times and he had the early beginnings of many of the chapters in the science of metals. Industry was burgeoning in many directions, for methods had been developed, especially in the manufacture of steel that provided materials in extremely large tonnages, permitting applications of metallic materials on a very widespread scale. These multitudinous new uses of metals created an increased interest in the behavior of metals, and provided the basis for the rapid development of a science of metals. Indeed, the development of science generally that accompanied the industrial revolution reached a flood tide toward the end of the century, furnishing the metallurgist basic principles in chemistry, physics, mechanics, and crystallography that would shortly be extensively applied to metallic behavior. In this account, the early developments in the wide metallurgical field will be traced, in order that the status of physical metallurgy in 1871, when this Institute was founded, may be clearly seen. The subject of metallurgy in antiquity has been written upon frequently and at length. We shall here no more than indicate the main features that we need to define the position in 1871 and to provide a proper background for discussing subsequent developments. The writings of Pliny,1 23-79 A.D., to which Robex-ts-Austen3 fre-

Jan 1, 1948

By C. W. A. Newey

I would like to make the following points in connection with the studies of the deformation of NiAl reported in the recent paper by Wasilewski, Butler, and Hanlon. 1) Much of their paper is concerned with demonstrating that slip occurs on either {110)(001) or {100)(001) systems. In their discussion they state "the existence of (001) as the basic slip direction can thus be considered established." This fact was established by the earlier studies of Ball and Smallman.32 Ball and Smallman also concluded that the slip plane was of the type (110) and they showed that cross slip or pencil glide on orthogonal (110) planes could produce macroscopic slip on planes of the (001) zones, e.g., (100). Wasilewski et al. refer to this paper by Ball and Smallman but not in connection with the slip system determinations. 2) Wasilewski et a!. eliminate the possibility of (111) slip in NiAl on dubious grounds. Their statement that ('the very high yield strengths of the (100) oriented crystals", in which (001) slip is constrained, "immediately ruled out the possibility of {110)(111) slip" cannot be accepted unequivocably; it would be reasonable if the crystals were completely brittle but they are not, as Wasilewski et al. and others33734 have shown. Their elimination of the possibility of (111) slip in a crystal compressed along [227] is misleading since there is no obvious reason why (111) slip should occur in a crystal of this orientation. In fact, from an analysis of the macroscopic surface markings on deformed (100) stoichiometric crystals, Pascoe and Newey34 have deduced that slip occurs on systems of the type {211)(111) and {321)(111). 3) Polycrystalline NiAl is known to undergo general deformati~n.Having emphasized that general deformation is impossible if only (100) slip occurs, it is a pity that Wasilewski et al. do not attempt to account for the disagreement between theory and their experimental results. Of course, (111) slip can provide the additional independent systems required for general deformation.

Jan 1, 1969

By Barry K. McMahon

The fundamental problem in rock mechanics is accounting for the discontinuous and anisotropic nature of the jointed rock mass. It is this problem that makes rock mechanics distinct from the mechanics of steel, glass, or concrete. Existing mathematical models explain much of the behavior of rock cores in the laboratory but, in civil engineering at least, the rocks that matter are the ones that are already broken. On the other hand, the basically descriptive methods now used in engineering geology do not lend themselves easily to mathematical analysis. A set of indices of geological properties related to the strength and deformation characteristics of jointed rock is needed. Like the index properties used in soil mechanics these will probably not have precise mathematical meaning, but once correlations are established with large scale tests they can form a basis for the transfer of test results, obtained in one area under one set of conditions, to the prediction of rock behavior in another area under another set of conditions. Indices of rock properties are even more important in rock mechanics than in soil mechanics as the cost of testing is much higher. To be useful, these indices must be easily and quickly measured and give reproducible results when measurements are made by different people. In this paper the word "joint" means all naturally occurring rock fractures with less than 3 in. of clay or other soft coating material. EXISTING INDICES OF ROCK PROPERTIES A comprehensive review of indices of rock properties for intact rock is given by Deere and Miller.' They provide charts ". . . for estimating the strength or modulus properties for intact rock from the numerical indices obtained by either the Schmidt hammer, the Shore Scleroscope,

Jan 1, 1968

By R. G. Treuting, W. C. Ellis

The twinned state is characterized by a lattice of coincidence sites. Imperfections are required at stable lateral twin interfaces. Twinned regions can occur with relative ease in the diamond cubic IN recent contributions1,2 on the origin and growth of cubic annealing twins, attention has been directed to the orientation relations between such twinned components and their parent matrix. There are some aspects of twinning which may be illuminated by a more detailed consideration of the twinned state" alone. As an extreme example, the dense twinning in cast ingots of germanium,&apos; as contrasted with the rarity of twins in cast face-centered cubic metals, is yet to be accounted for. It has been this that has led us to the present work, which, it will be noted, uses methods and constructions in many respects similar to those of Kronberg and Wilson.&apos; In the cubic systems, a 70" 32&apos; rotation about a <110> axis is angularly equivalent, as to twinning, to the more usually considered 180" rotation about a <111> axis. Figs. 1 and 2 show a (110) projection of a twinned face-centered cubic lattice and a twinned diamond cubic lattice. In both figures, the two adjacent planes A and B, shown by the larger and smaller circles, are sufficient to represent the entire array. In each case a section of lattice, the original atom sites of which are shown by open circles, has been rotated as indicated through 70" 32&apos; to bring an original. [112] direction into coincidence with the [112] diiection. The latter is the intercept on the (110) projection of the (ill) plane normal thereto, the twinning plane. In the face-centered cubic case the rotation can be performed about an axis passing through an atom-site; the mirror plane then is also a composition plane containing atoms common to both twinned and untwinned lattices. The diamond cubic lattice may be construed as two interpenetrated face-centered lattices. Its (111) planes recur in a sequence of alternately short and long interspacings. Consequently a mirror plane for twinning cannot be a composition plane, but must be the bisector of one of the spacings. When the longer spacing is selected, the closest distance of approach across the mirror plane in the [ill] direc- tion is identical with that in the untwinned structure. In each case periodically recurring (ill) planes (parallel with the twinning plane) are found, on which there is coincidence of atom sites of the pre-twinned and twinned orientations; these are indicated by the cross-hatched circles. In the face-centered lattice there is such coincidence every third (ill) plane; in the diamond cubic lattice, on two adjacent planes in every six. At the twinning interface in the latter, there is on each side of the mirror plane a (ill) plane of atoms common to both twin components. Conceivably, there is little influence on a plane of atoms about to be adhered to such a pair of coincidence planes, whether it be laid down in a normal or in a twinned position with respect to the previously formed structure. Slawson% as attributed the high incidence of twinning in diamond to this boundary state. Further examination shows that the motion of intermediate planes can consist of various pairs of equal and opposite translations, for example of (ill) planes in the [l&apos;;i2) direction, the familiar twinning shear, indicated in the small schematics in the figures. Since the translations form a system of shears of alternating sign between coincidence planes, twinning could take place by such a mechanism over an extended region without extensive shear; in fact, in this case any atom moves but the distance in the [1i2] direction. One alternative construction for the face-centered cubic lattice leading to the same end result is illustrated in Fig. 3. The plane (711) with respect to the pretwinning orientation (the twinning plane of Fig. 1) is given, the twinned region arbitrarily bounded by <110> and <112> directions. The coupled shear is identical to that of Fig. 1. The "rotational" movement about coincidence sites generating the same twinned position could consist as shown of the translation a,/d% for each atom of a group of three in the B layer in a different one of the three <112> directions, and a similar translation of the underlying three atoms in the C layer in either the same or the opposite sense. This is not dissimilar to Kronberg and Wilson&apos;s construction for their 22" rotation of three adjacent (111) planes.

Jan 1, 1952

By William P. Blake

IN southern Arizona and in Mexico the word caliche is in general use to denote a calcareous formation of considerable thickness and volume found a few inches, or a few feet, beneath the surface-soil, upon the broad, dry, gravelly plains and mesas. In western South America the same name is applied to the beds of crude soda-niter (Chili saltpeter). While these deposits of South America and of Arizona are totally different in composition, and have nothing in common, except that both occur in layers in the strata near the surface, it is probable that an explanation of the origin of the calcareous beds may equally apply to the accumulation of sodaniter and other deposits of easily soluble minerals. But the name, taken from the Latin, Calx, is more appropriate to the calcareous beds than to those of niter. Caliche has a wide distribution in the arid regions of Arizona and Mexico. It is usually hidden from view by a slight covering of soil; but it is easily found by digging, and is often revealed by a flow of water during heavy rains. It is practically a continuous sheet, from three to fifteen feet thick, of earthy limestone or travertine, through which the smaller plant-roots find their way with difficulty. The presence of this comparatively impervious layer of cemented earth may account for the absence of trees, or of the larger shrubs, over wide areas. The shrubs which gain a foothold are those whose roots do not extend far downwards, and which do not require much water, such as Larrea Mexicana and the [Cactaceoe]. If trees are planted, it is necessary to break up the caliche by blasting, or at least to crack the upper layers. The top of the caliche is more dense and solid than the lower portions. The surface of this top crust, or layer, is comparatively smooth, though undulating, while the lower portions, under the crust, are irregular, cavern-

Jan 1, 1902

By W. Geo. Waring

The winning of zinc and lead ores from the comparatively shallow deposits of the Joplin district presents few such problems for the mining engineer as are encountered in deep ore mining and in the handling of complex ores. However, for those who are interested in the origin and nature of ore deposits in general, there is much here to investigate, and upon studies in this direction will depend, in no small measure, the future of an industry that has produced during the year 1916, in southwest Missouri, lead and zinc ores to the value of $26,319,383; adding $46,022,164 to the metallic wealth of the nation. Including the adjacent mines in Ottawa County, Oklahoma, and Cherokee County, Kansas, which are really continuations of the Joplin district, the total value of ores produced reached the sum of $34,089,503, and that of the metals, $58,927,941.l The ores produced in the Joplin district are remarkable on account of their almost uniformly high metal content in both lead and zinc. Their superiority in this regard is unparalleled, and is doubtless due to certain geological conditions that are now possibly explicable, provided that the artesian circulation = ascension hypothesis of the origin of the ore deposits is proved beyond question to be the only tenable explanation of the facts. These, as well as other valuable zinc-ore deposits, are bound to be exhausted in time, for ordinary mining purposes, and it concerns the mining engineer that the conditions under which ores of this character were actually deposited in the form in which they occur, may, if possible, be ascertained, in order that he may learn where to look for similar deposits in other regions, or even how to reproduce artificially such condi-

Jan 1, 1918

By P. H. Griffin

WHEN a subject, such as the manufacture and service of chilled car wheels, as has been fruitlessly discussed for ten or fifteen years, it is difficult to revive interest and action by the mere repetition of statements and arguments that have been made before. And when a situation involves serious responsibilities for conditions that have grown up under circumstances beyond the control of any particular individuals or authority, it is even more difficult to deal with. But there is one phase of every subject that need not involve these particular points if presented in a, proper manner; and that is, " the future state." I will try to present the subject of this communication from the latter standpoint and with the hope that all of those interested will feel disposed to give the matter attention from the basis that it is a, vitally important one to all that travel on railroads, whether as employees or officials, or as dependent on those in charge of the operation, or in the matter of materials and equipment used. The conditions of chilled wheel service have been changed so radically in the past ten or fifteen years by the use of freight cars of 40 and 50 tons capacity, that it is fair to say in the interest of all concerned in the use and in the manufacture of such wheels, that the increased strains and loads have been quite sufficient to account for much of the service results that have transpired. That proper provision was not made for increased possibilities of strength and wear, in fact that previous factors of the kind were allowed to deteriorate, is no proof that such wheels cannot be made equal to heavy service conditions as shown in the data given herein.

Jan 10, 1913

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 ½ times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.1,2 Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.4 Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the caprock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1952

By W. Mckewan, W. M. Fassell

The oxidation rates of copper have been determined at temperatures from 600" to 900°C in oxygen from 14.7 to 400 psi total oxygen pressure. The oxidation rate of copper is unchanged by oxygen pressures within the range studied. The observed data extend Feit-knecht&apos;s conclusion concerning the pressure independence of copper from atmospheric pressure to 400 psi. All samples studied in the above-mentioned temperature and pressure range have both Cu2O and CuO present in the oxide film. NUMEROUS papers have been published on the oxidation of copper, some of which have noted the effect of oxygen pressure on the oxidation rate of copper. It must be noted, however, that no data on the oxidation rates of copper at pressure in excess of 1 atm have been reported in the literature. (Le Chatelier¹ reported that a black oxide of silver was formed at 300°C and 15 atm pressure.) This is likewise true for the other metals. This investigation was initiated to obtain experimental oxidation rate constants for pure metals at elevated temperatures and high oxygen pressure. Copper was selected as the first metal since probably more reliable data are available on its oxidation rates and related physical and chemical properties than for any other metal or alloy. As a general summary, the following conclusions appear well established for the oxidation of copper: 1—The oxide coating consists of Cu2O with a superficial coating of CuO providing the ambient oxygen pressure exceeds the equilibrium pressure for the coexistence of Cu2O and CuO.² The following sequence of phases is then Cu/Cu2O/CuO/O2 (gas). The Cu2O consists of large crystals that have no relation to the orientation of the metal crystals, except for a very thin layer adjacent to the metal." The CuO consists of very fine crystals randomly oriented. If the oxygen pressure is below the equilibrium pressure for the coexistence of Cu2O and CuO, the coating consists of Cu,O only. 2—The rate-determining factor in the parabolic oxidation of copper is the diffusion of Cu+ ions through the Cu,O layer.4,6,7 The Cu+ ions are accompanied by electrons to maintain electrical neutrality. The mechanism of the reaction at the Cu2O/CuO interface and the method of growth of the CuO is in some doubt. 3—On copper, there are three reported pressure effects: (a) At pressures below 0.3 mm Hg oxygen pressure, the oxidation rate increases directly with pressure.&apos;, &apos; .Vxygen starvation at the surface may account for this effect. (b) At oxygen pressures from 0.3 to 63 mm, the oxidation rate increases as the 7th root of the oxygen pressure providing the temperature is such that only Cu2O is present in the film. (c) At pressures from above the equilibrium pressure for the coexistence of Cu2O and CuO (varies with temperature) to atmospheric pressure, the oxidation rate is independent of the oxygen pressure.&apos; Equipment In order to determine the oxidation rates of metals in an oxidizing atmosphere at pressures up to 400 psi, the equipment is somewhat different than for low pressure work as is shown in Figs. 1 and 2. A Leeds and Northrup Micromax recording controller (A) is used to control the temperature of the Ni-chrome furnace winding in conjunction with a Micromax electric drive unit. The drive unit adjusts a 20 amp Variac (variable transformer) to control the power input into the Nichrome furnace winding. Due to the "self heating" of the sample by oxidation, frequently encountered in oxidation rate studies, it is essential that the sample temperature be measured independently. This is done by means of a series of six chromel-alumel calibrated thermocouples located spirally around the oxidizing metal sample. Each thermocouple is partially shielded from the direct radiation of the furnace wall by

Jan 1, 1954

R. 8. MACPHERRAN, Milwaukee, Wis. (communication to the Secretary): The importance of carbon in pig-iron, as well as the desirability of buying, for some purposes, irons which are high in carbon, has always been recognized. Mr. Summers, I think, has given undue weight to the carbon-determinations. The combined carbon often decreases materially as the center of the pig is approached, with a corresponding increase in the graphite. Even the determination of total carbon, to be of service, must he supplemented by that of other elements. By it alone, the softness of a foundry-iron cannot be determined. Car-wheels and No. 5 iron, for instance, frequently contain 3.75 per cent. of carbon. This is the percentage specified by Mr. Summers for his No. 1 iron, " with the silicon about anywhere the furnace-man wants it." It is true that, other things being equal, the higher the carbon the softer the iron for foundry-use. But to introduce any given percentages of graphitic and total carbon into a pig-iron specification would but make the specification more complicated, without increasing its value in a commensurate degree. Mr. Summers does not believe in the governing of mixtures by the silicon, and, in support of his views, gives several tables. It seems to me that both his conclusions and his tables are somewhat unsatisfactory. He comments on the irregularity in carbon, but fails to note the significance of the irregularity in silicon..The variation of 0.7 per cent. in silicon, for example, is too great to be accounted for by difference in blast. It might better be attributed to bad grading at the furnace, unsystematic sampling, or irregular charging. Deductions drawn under such conditions are of little value. In ordinary work the castings from the same mixture should

Jan 1, 1899

By Wilbur E. Sanders

At some period during the operation of metalliferous and other commercially valuable mineral-deposits in connection with their underground mining, when the developments therein have become so extensive that their description is tedious and confusing, some scheme for naming or numbering the various workings and their parts is necessary for convenience of reference. A simple and symmetrical yet expansive system of classification must be devised, one that is capable of being extended to cover all possible exigencies and conditions of future operations within the property. Such a scheme, properly arranged, greatly simplifies communication between the various departments of the mining business, as, for instance, between the administrative and the operating departments of the concern, and is of the greatest assistance to the officers of the mine in enabling them to locate and describe particular points and parts of workings and specific kinds of work. Again, in the proper segregation and differentiation of mine-accounts, when they are carried out with that detail which will furnish ready information concerning the cost of a particular piece of work, or the various items and totals of expense connected with the development, operation and repair of each or all of the mine-workings, some such method of clesignatioi~ becomes a necessity. Moreover, such a plan is acl- mirably adapted to the needs of the mining engineer, who, in connection with his reports upon mining-properties, is sometimes required, in his descriptions of certain blocks of ore, to locate lists of assays of samples taken from many and various places, and to designate workings and parts of workings that are located in different parts of the mine, sometimes at points wide apart. To write out in full a sufficient description of any particular

Jan 1, 1907