Search Documents

By Clarence Zener

The internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites, localized weak regions introduced by cold-working,6'7 grain boundaries and possibly twinning planes.8'9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3.i in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff. Experimental Method The experimental method used has previously been described in institute papers.5'6'9 The measure of internal friction adopted here, I/Q, is X the logarithmic decre- ment, a measure used by some writers, and is also X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. Experimental Results The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. I, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of 100 during the next Ioo° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e-H/RT [I]

Jan 1, 1943

By Clarence Zener

The internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites, localized weak regions introduced by cold-working,6'7 grain boundaries and possibly twinning planes.8'9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3.i in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff. Experimental Method The experimental method used has previously been described in institute papers.5'6'9 The measure of internal friction adopted here, I/Q, is X the logarithmic decre- ment, a measure used by some writers, and is also X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. Experimental Results The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. I, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of 100 during the next Ioo° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e-H/RT [I]

Jan 1, 1943

By Howard Hughes

IN drilling for water and oil to reasonable depths through the generally soft yielding clay and sand formation of the Coastal Plain of Texas, . Louisiana, and Mississippi, the rotating method of drilling was adopted, principally on account of the easy and quick penetration, and the low cost of the drilling plant. In favorable ground, free of heavy gravel and rock strata, as much as 1,000 ft. has been drilled in less than 36 hr., although such performances were of course rare. Hydraulic rotary drilling, or, as it is now called, rotary drilling, was used in the above States as early as 1880. The plant consisted of an ordinary derrick, a 25-h.p. boiler, a small hoist, a steam pump, and a water swivel with hose attachment, and an ordinary flat diamond-pointed bit. The successful drilling in of a phenomenal oil well by this process on Spindletop, near Beaumont, Texas, on Jan. 10, 1901, and the ascertained impracticability of drilling subsequent wells in the same locality by other methods (owing principally to heavy quicksand under pressure from below), brought rotary drilling into great prominence, practically to the exclusion of any other process throughout the Coastal Plain, and later on elsewhere. The method, as its name implies, involves the rotation of a pipe by means of machinery placed on the derrick floor. A drill bit attached to the lower end cuts a clearance for the drill pipe, with much the same motion and effect as an auger. Water forced through the drill pipe by means of a pump, and escaping through the bit, removes the cuttings and returns to the surface outside the drill pipe. In this manner the hole is kept open, permitting the drill stem to rotate freely. The pressure of the column of muddy water holds up the walls of the hole until it has been cased. Practically all the wells of the Gulf coast region, numbering nearly 10,000, have been drilled with this system. During the last five years its use has been extended to many other States and countries.

Jan 3, 1915

By H. B. Huntington

Some of the basic problems in understanding elec-tromigration in metals are discussed, along with the attempts that are being made to handle them. One such problem is the effect of the electrostatic forces. It is now acknowledged that the momentum exchange with charge carriers plays generally a dominant role in the driving force but the question remains to what extent the electrostatic force may still be effective. The electromigration of interstitial impurities is also an area which presents some intriguing questions. For the substitutional impurity, moving by the vacancy mechanism under the influence of an electric field, the correlation considerations are somewhat more complex than have been previously recognized. Another problem of basic importance in the calculution from first principles is the strength of the "electron friction" force, say for a simple one-band metal. A related problem growing out of the preceding is the prediction of the direction of the "electron wind" force for metals with band structure involving both holes and electrons. THE term electromigration has come to be used to describe the flow of matter in condensed phases carrying high electronic currents such as metals and alloys, whereas one usually reserves the term electrolysis for situations where the current is largely ionic, particularly in the liquid state such as molten salts. It follows that the mass transport number in electromigration is always very small, of the order of 10-7. Studies of electromigration date back some 30 years but the modern period would appear to date from the work of Seith and Wever1 who in the mid 1950's first incorporated markers to display mass motion relative to the lattice and first suggested that the direction of the mass flow was primarily determined by the sign of the charge carriers. Since that time interest in the field has grown steadily and more rapidly recently as certain technological applications became apparent. Chief of these is certainly the deleterious effects that electromigration can cause, even at relatively low temperature, to current-carrying elements in integrated circuitry.2 These phenomena have been the subject of intense study and considerable ingenuity. On the constructive side electromigration has proved a useful tool in the purification of certain metals.3 The interest of this paper is, however, centered more on the basic aspects of the subject than on its technological applications. That high electric currents should give rise to mass flow in metals and that the driving force should be more directly associated with momentum exchange with the charge carriers than with the electrostatic field are ideas that no longer cause surprise or particular interest. The field has matured to the point where the general concepts are widely accepted and continued progress in basic understanding rests on more detailed and quantitative exploration. It is the purpose of this paper to point out what are some of the current problems. As a result, we expect to raise more questions than we answer. The first of these will be the role of electrostatic forces, if any, in electromigration. A second section will deal with the electromigration of interstitials. A third and final section treats with electromigration of substitutional impurities or of the matrix atoms themselves. ELECTROSTATIC DRIVING FORCE In the conceptual treatments of electromigration it has been customary to write the driving force in terms of an effective charge number Z* and to divide it into two terms F = e£Z* = e£[Zel- z(pd/Nd)(N/p)(m*\m*\)] [1] The first of these represents the electrostatic force under immediate consideration in this section and the second and usually dominating term for metals arises from momentum exchange with charge carriers, commonly called the "electron drag" term. As can be seen it is set proportional to the electrons per atom, z, and the ratio of the specific resistivity of the moving entity to the corresponding resistivity per matrix atom. The (m*/Im*I) factor takes into account the fact that the sign of the charge carrier determines the sign of the driving force. The specific resistivity of the moving entity is averaged over its path. In the case of motion of the matrix atoms by vacancies this gives rise to approximately one-half the resistivity at the saddle point since the scattering power of the atom at its equilibrium position bordering the vacancy differs only slightly from that of a normal matrix atom. Although the formulation of the "electron drag" term in Eq. [I] is based on a highly simplified model for electron defect scattering, the essential features implicit in the expression are common to all the theoretical approaches that have so far appeared in the literature.4-6 As for Zel, most treatments of electromigration have included the quantity as the parameter which measures the direct interaction of the electrostatic field with the ion and equated it to the nominal valence of the latter. However, there has been considerable discussion whether this interaction may not be 0 in many cases.6 If the moving ion is always enveloped by the same distribution of shielding charge, then clearly its motion will not involve any work done by the electric field and one can expect there will be no electrostatic force exerted on such a neutral composite. From this point of view the shielding charge around the ion would be said to be complete and hence the entity within the Debye shielding sphere would be unaffected by the electrostatic field per se. There is, however, the prospect that, as the moving ion progresses, new charge comes in to participate in the shielding action

Jan 1, 1970

By R. Norman Orava

The strain-mte behavior of. the tensile yielding and flow characteristics of arc-cast polycrystal-line molyhdenum of pidrity > 99.97 pct was investigated in the range 10-6 to 10-1 sec-1 at 243o, 293o, and 373oK for two grain sizes, 0.027 and 9.098 mm. For 0.998 mm, the strain-mte dependence of the lower yield stress can be described by a straight line of the jowl a, = a + 0 log e over the whole range of strain rates examined. However, for 0.027 mm, the data fit several consecutive linear relationships of the above form. The previous association of these different linear regions with different rate -controlling mechanisms is questionable for molyhdenzdm. The senlilog strain-rate dependence of the yield stress is consistent with Hahn's model for yielding when the stress dependence of the mobile dislocation density, pr, is taken into account. Since p', from rate -cycling experirnents, is found to be relatively insensitive to stress for single crystaIs, the obserzied log-log dependence of their yield stresses is also in agreement with the model. A correction for the stress dependence of p' changes the activation oolurrze for yielding from a zero to a more realislic inverse function of stress where the Peierls mechanism is believed to be rate-controlling. The gmin-size dependence of the lower yield stress is not a monotonic junction of strain rate. RECENT experimental evidence' has revealed that the strain-rate dependence of the tensile lower yield stress, a,, of commercially pure ni- obium and tantalum tested at room temperature can be described by several consecutive semilog relations of the form: sv =a + ß log € [1] where i is the applied strain rate and a and 0 are constant Over only relatively small ranges of strain rate. Three linear regions were found for niobium and four for tantalum. Each linear region was interpreted as being associated with a different rate-controlling mechanism on the basis of the current

Jan 1, 1964

MINING and Metallurgy closed the year 1928 showing a small profit, the receipts, exclusive of the charge against members, dues for subscriptions, having been $43,067.81, and expenditures $40,925.58. In accord with the policy of the Board the budget is made each year with the purpose of balancing the accounts rather than the maximum of profit from the undertaking since it is the service the journal performs for members that justifies its existence. This service is being constantly increased. Within the year a number of changes have been made in the dress of the magazine, a new cover adopted, color more frequently used, and illustrations more generally employed. These changes seem to have been appreciated both by readers and advertisers. More space has been devoted to papers read before local sections and to the news of their activities. It is believed that this has helped materially in sustaining and increasing the interest in such meetings. The general, regional, and division meetings have also been fully reported and news of Board meetings, of the work of the various committees, of the employment service and other activities of the Institute has been spread before its members month by month. The 570 pages of reading matter printed in the course of the year constitute not only a record of what the Institute was doing but of what the most representative sections possible of the members of the mining and metallurgical professions were thinking. With 9000 members scattered around the world, occupying key positions in the industry, the Institute affords through its own journal an unsurpassed medium for broad contact and enables the readers with the minimum of expenditure of time and at no extra money expense to keep a general contact with the whole range of subjects touched by miners and metallurgists. In these days of intense specialization but rapid change such contact is particularly valuable. The more formal papers presented to the Institute are published in the Transactions, Technical Publications and the special volumes. Mining and Metallurgy carries abstracts of all papers published ,by the Institute and prints in full the shorter, less detailed papers and those which reflect work in progress rather than finished. Such papers have a news value which is supplemented by editorial comment, discussion by members and others, and the actual news of the organization itself. Without therefore attempting to fill the place of a general news sheet, it has a timeliness that gives it an immediate value much appreciated by the readers. In accord with the general policy of the Board every effort will be made constantly to improve the quality of the magazine to the full extent that its revenue will permit. Your Committee feels that, through the intelligent cooperation of the official staff in the office, Mining and Metallurgy has been improved in

Jan 1, 1929

By F. S. Norcross

MANGANESE has long been considered one of the United States' most important strategic raw materials. Its indispensability in steel manufacture makes it vital to the nation's industrial life. Coupled with this indispensability is the fact that domestic producers have not been able as yet to supply more than a small part of the nation's manganese needs; consequently the United States has had to depend upon such distant foreign sources as the U.S.S.R., British India, the African Gold Coast and Brazil for the major portion of its ore. The great bulk of the mineral is consumed in the form of ferromanganese, an alloy that averages 8o per cent manganese and 20 per cent mainly iron and carbon. Manganese is used as a deoxidizer and desulphurizer in steel manufacture. By combination with the residual oxygen and sulphur of the bath, it helps to produce a clean, sound metal. Approximately 14 lb. of manganese, it is estimated, is used in making one ton of steel. For standard-grade ferromanganese, the ore should have a minimum of about 48 per cent Mn and preferably more. Beneficiation methods have not yet been developed for making the immense low-grade deposits in the United States salable at prevailing prices. Dependence upon foreign sources thrust the United States into serious difficulties during the World War. At the start of hostilities in 1914, the nation was obtaining about four-fifths of its ore from the Eastern Hemisphere. Domestic production had been negligible, amounting to only 3000 to 7000 tons a year. As the war continued, shipments from the East, endangered by sea attack and blockade, dwindled rapidly. Imports from Brazil mounted. In this grave emergency, the United States, starting almost from scratch and under the stimulus of high prices, succeeded by 1918 in producing a peak of 311,000 tons, about 3 5 per cent of its consumption that year. Since the war, the United States has depended upon foreign sources for more than nine-tenths of its high-grade ore. During 1936, 1937 and 1938, imports for consumption averaged 736,000 tons a year. During the same period, domestic shipments averaged 21,000 tons a year. Of the imports, the U.S.S.R. accounted for an annual average of 280,000 tons, the Gold Coast 208,000 tons, India 74,000 tons, and Brazil 72,500 tons. But India and Brazil, which in 1936 ranked third and fourth in the list of importers, were displaced in 1937 and 1938 by a new and much nearer source-Cuba. From less than 1 per cent of United States imports in 1931, the island republic increased its shipments to more than 27 per cent in 1938. Cuba's average for this three-year period was 97,000 tons, and its total for 1938 was 131,000 tons.

Jan 1, 1940

By Dean Edwin Dallin

A computer system was developed by Texasgulf's Corporate Data Center (at Raleigh, North Carolina) to evaluate the economics of proposed new projects and to determine the incremental expansion effects of existing projects. The Corporate Treasurer, Controller, and Senior Staff Members of the corporate office guided the project with advice from the Chairman's office. After consideration of commercially available programs, the decision was made to develop an in-house investment system. The main specification was that the program must do the accounting calculations on the computer exactly as done by hand in the corporate office. No average "approximations" or values were allowed. Also, the capability to change the calculation procedures quickly was a must. The experience gained in developing a program to evaluate Gulf Coast off-shore oil lease-bids was used to develop an investment system. Several ideas were taken from A Programming Language (APL) concepts. An investment functional language was developed, and computer programs were written to process the functional language. One feature is a print-out of the model in English. The English print- out assists the debugging and documentation of a model. The major expansion at the Kidd Creek mine was the test case for the new system. After the results were approved and accepted for the base case, many sensitivity runs were made. Numerous additional models were developed to reflect the investment opportunities at other sites. An existing edit program was used to build the models and to systematically organize all the data for different projects. Remote input-output capabilities were added to the system, allowing data to be prepared and submitted at one Texasgulf site with the results printed at another location within minutes. The project has been well accepted by Texasgulf's senior management. Growth of the system is now in the areas of (1) merging individual projects into the corporate financial statements, (2) use of classical forecasting to project future costs, and (3) coupling the investment program to mine planning and general ledger systems. Also, the system is now being installed on an interactive computer system to provide faster turn-around time and more flexibility.

Jan 1, 1977

By J. J. Forbes

THE Federal Coal Mine Safety Act (Public Law 552, 82nd Congress) was approved on July 16, 1952. It incorporates, as Title I, the Coal Mine Inspection and Investigation Act of May 7, 1941 (Public Law 49, 77th Congress), which gave Federal inspectors only the right to enter coal mines for inspection and investigation purposes but no power to require compliance with their recommendations. Title II contains the enforcement provisions of the act; its purpose is to prevent major disasters in coal mines from explosions, fires, inundations, and man-trip or man-hoist accidents. At this point a brief account of events that pre- ceded the enactment of the Federal Coal Mine Safety Act seems appropriate. The hazardous nature of coal mining was recognized by the Federal Government as long ago as 1865, when a bill to create a Federal Mining Bureau was introduced in Congress. Little was done, however, until a series of appalling coal- mine disasters during the first decade of this century provoked a demand for Federal action. As a result an act of Congress established a Bureau of Mines in the Department of the Interior on July 1, 1910. The act made it clear that one of the foremost activities of the Bureau should be to improve health and safety in the mineral industries. One of the first projects selected by the small force of engineers and technicians then employed was to determine the causes of coal-mine explosions and the means to prevent them. By investigations after mine disasters the fundamental causes and means of prevention were soon discovered, and the coal mining industry was informed accordingly. However, despite this knowledge and the enactment of State laws and the Federal Coal Mine Inspection and Investigation Act of 1941, mine disasters continued to occur with disheartening frequency and staggering loss of life. The devastating explosion at the Orient No. 2 mine on December 21, 1951, resulted in the death of 119 men. The Orient disaster rekindled the memory of the Centralia, I11., disaster of March 25, 1947, which caused the death of 111 coal miners. These two tragedies ultimately brought about enactment of the Federal Coal Mine Safety Act.

Jan 1, 1954

By C. P. Fiske

The pottery of the New Jersey Zinc Co. (of Pa.) is equipped to make three classes of refractories; namely, spelter vessels, spelter condensers, and high-grade fire-brick. The most important of these are the spelter vessels, on account of the extreme severity of the service which they must perform, necessitating great care in the selection of materials and in the whole process of manufacture. Next to the spelter vessels in importance come the condensers, as large numbers are used in the manufacture of spelter, and improvements in quality result in material decreases in working cost. While the fire-brick which form the laboratory, or high-temperature portion of the spelter furnaces, are placed at the foot of the list, they are nevertheless of much importance, since high quality will decrease the frequency of the always expensive shutdowns for repairs. To promote simplicity, the manufacture of these three products will be described separately in this paper, except in so far as materials and the crushing and handling system common to all are conccrned. Materials Bond Clay.—The bond clay used entirely at the Palmerton pottery is a St. Louis clay furnished by the Grand View Fire Clay Co. It is stored in a system of covered bins, and no attempt is made to weather it in the accepted sense of the term " weathering." Some years ago our clay was weathered before pugging, but we did not find the benefit sufficient to offset the additional handling and the loss of clay incurred. Furthermore, we believe that the rotting of the pugged mix (described later) accomplishes the same results to better advantage. That there is some action taking place in the clay while stored in the covered bins, however, is evidenced by an increase in volume which at times has caused damage to the retaining walls of the bins. We have at present a stock of bond clay weathering in the open, and when this is put into service an opportunity will be afforded for making comparisons with the clay as usually handled.

Jan 1, 1918

By Chas. A. Dobbel

The Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. Pmine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the Gear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was used to drive prospect holes with jointed steel. Just what equipment to develop for this work with the hammer drill involved much experimenting, as nothing was found in the literature

Jan 1, 1925

By John Gjers

Being on a visit to your great and prosperous country, and having been favored with an invitation to attend this meeting of your Institute, the author has been requested by your Secretary to give a short account of his invention of the " soaking-pit," which he has great pleasure in doing. The object of the soaking-pit is the rolling of steel ingots with their own initial heat, that is, to supply the missing link in that chain of metallurgical operations which Sir Henry Bessemer began in 1857, when he proved how it was possible to produce malleable iron or steel direct from the fluid cast-iron out of the blast-furnace, without any further direct use of fuel. The great Bessemer invention has revolutionized iron and steelmaking throughout the world; but it stopped short at producing the ingot, which, it was found, had afterwards to be heated in a furnace to enable it to be rolled or hammered; and it is only lately, twenty-five years after Mr. Bessemer's announcement, that the author of this paper has been able to show that furnacing can be dispensed with, and that it is practicable to roll a steel ingot into say a bloom, a rail, or a billet, with its own initial heat. It has no doubt suggested itself to many that there ought to be heat enough in the ingot just cast, for the purpose of rolling; and from time to time attempts have been made to utilize this heat; but such attempts always ending in failure, it became a settled opinion in the trade that it could not be done—an opinion which the author is aware that your late lamented countryman, Mr. Holley, than whom there was none more conversant with Bessemer steel-making, also entertained. But settled opinions sometimes prove to be great fallacies. As an instance, it is not many years since the opinion prevailed in the trade that steel ingots could not be rolled successfully, that is, so as to make good rails, unless they were first allowed to get quite cold, and afterwards heated. No greater boon was ever conferred on the

Jan 1, 1885

By G. E. Murray

Lead blast-furnace work at Trail is unique in that this is the only plant in the world where blast-furnace smelting on a large scale for both lead and zinc recovery is carried on under one management. On this account the factors that determine economic practice differ from those of other lead smelters. In addition to this different metallurgical outlook, a great deal of structural investigation has been carried on, which has resulted in the development of a furnace which should prove of interest to all who are faced with similar problems. This description may be conveniently divided into various heads as follows: (1) General—make-up of charge, etc.; (2) structural—(a) hoods and charging methods, (b) shaft construction, (c) crucible construction; (3) handling slag; (4) handling bullion; (5) metallurgy. The Charge The Trail plant is an old one, on a congested site. As with most old plants, this limits the method of charge preparation. In general, lead metallurgists will agree that sinter when it reaches the blast furnace should contain as small an amount as possible of actual fines. There would be some difference of opinion as to the maximum size as well as of the minimum required, but to obtain the optimum condition some form of screening is indicated. This screening should take place immediately before the blast furnace if possible, and because sinter deteriorates in storage there should be as little as possible. There should also be the minimum amount of handling between the sinter machines and the furnaces. Unfortunately, at Trail the sinter must be handled considerably before it is charged to the furnace, and no feasible scheme of screening has yet been devised. Trail practice, then, demands that the sinter be a strong one physically. Dependent upon the amount of lead in it, it has been found advantageous to incorporate granulated slag into the final sinter, the amount varying inversely as the lead content. The addition of this slag makes a harder sinter, which arrives at the blast furnace in a better condition, but it entails some lack of efficiency, because desulphuriza-tion is not so rapid nor so complete.

Jan 1, 1937

By Blamey Stevens

The following paper aims to make a full explanation of the phenomena of rock jointing. It may be unnecessary to give any general description of what are termed joints in rocks, but Professor Geikie's clear and faithful generalizations are so illuminating that no excuse need be given for introducing the following and other quotations into this paper : " Almost all rocks are traversed by vertical or highly inclined divisional planes termed joints. These have been regarded as due in some way to contraction during consolidation (fissures of retreat) ; and this is no doubt their origin in innumerable cases. But, on the other hand, their frequent regularity and persistence across materials of very varying texture suggest rather the effects of internal pressure and movement within the crust." 1 General Explanation.—In this paper I show that the phenomenon of jointing may to a large extent be accounted for by the pressure of the water contained in the pores of the rock. To understand this, each constituent grain of the porous material may be considered to be separately compressed by the water which submerges it. As all the grains are held together by cohesion, the whole mass is contracted by this pressure. In an indefinitely extended mass, however, there must be a limit to the possible contraction without rupture, because the material is restrained from moving freely by other material around its boundariee. The mass of rock thus becomes broken up. This phenomenon is known as " shrinkage" jointing. The term " shrinkage " is an apt one, if it be understood that the shrinkage of the rock is often brought about by change of stress. Stresses.—The compressive component of water stress on the individual grains is evidently the same as that of the water with which it is in contact. This is so, both before and after the jointing is formed. Before the jointing is formed there is, however, a tensile stress in one or more directions which keeps the material from contracting. At the moment of the formation of joints this stress is equal to the cohesive compressive stress. This is more commonly known to engineers as the tensile breaking stress.

Jan 1, 1914

By T. A. Wright

THE SAMPLING of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called' "metallic button" or "metallic recovery" or "metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can be readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also.

Jan 1, 1928

By Van Dyne Howbert, Fred E. Gray

The Presidio mine of The American Metal Co. of Texas is situated 45 miles south of Marfa, Texas, a town on the Southern Pacific R. R., and lies approximately 20 miles north of the Mexican border. Communication with the railroad is maintained over a state highway. All supplies for mine and mill are hauled in by truck from Marfa and precipitates and concentrates are freighted to the railroad by the same means and shipped to Selby and El Paso, respectively. The mill is at the town of Shafter, 1 mile from the mine and at approximately 350 ft. lower elevation. The ore is conveyed to it by an aerial tramway which requires practically no power on account of the difference in elevation. The mill is a countercurrent decantation cyanide and gravity concentrating plant of 200 tons daily capacity. Coarse and fine crushing are done at the mill. Two neal-by shallow wells in the bed of Cibolo Creek furnish an abundance of water. Power is generated for the mill and town by a Diesel engine plant. Ore Treated The ore is oxidized and siliceous. The greater part contains approximately 16 oz. of silver per ton, but mixed with this are many particles of ore of much higher grade, assaying in many instances 100 oz. or more. In the 16-oz. material there is an almost constant amount of silver which is difficult to recover by cyanidation. The high-grade material contains a much greater proportion of silver which is easily amenable to cyanide treatment. Thus, as the grade of ore becomes higher, the percentage of recovery of silver increases rapidly, under equal milling conditions. The silver minerals contained in the ore are principally argentite and cerargyrite, the former predominating The lead minerals, all of which are argentiferous, are chiefly cerussite and galena, with occasionally a little anglesite. The gold is free; most of the ore contains merely a trace

Jan 1, 1935

W. D. BRENNAN,* Cheyenne, Wyo. (written discussion?).-My experience has been that, where possible, it is preferable for each foreman to employ his own men, rather than to have them handled through an employment bureau. The fact that each foreman comes into direct contact with the man before he is put to work gives him an opportunity to choose, at certain times, the kind and class of men that he wishes. Where possible, after a man is employed he is sent to a central office where a complete history of each individual is kept on a card. If a man has previously been in the employ of the Company, his history can be obtained from this card, and if for any reason he is not wanted he can be refused work at the time he reports to, the central office. In connection with Workman's Compensation costs, we in Wyoming feel that although the rates of compensation paid may in some cases be rather low our law works satisfactorily. As the State and the number of employees are small, compensation cases are handled through Judges of the various District Courts. In the State Treasurer's Department, a few clerks were added to look after the handling and issuing of warrants and compiling of statistics. Most of the large employers have an arrangement by which a joint claim and assent, specifying the amount of compensation due, is made tip by the employer and signed by the workman. This is forwarded, to the Judges so that personal investigation of individual cases is not necessary. In this manner, compensation is promptly received and' overhead expenses of operation of the law is kept at the minimum. The law requires each employer to pay into the State Treasury, for the benefit of the industrial fund, a sum equal to 1.5 per cent. of the money earned by each employee, engaged during each calendar month of such employment. Each employer contributes monthly, unless the sum heretofore contributed, after deducting all payments made on account of injuries to his employees, shall equal a full 1.5 per cent. of his annual pay roll, computed by multiplying his current monthly pay roll by twelve, and shall likewise be not less than ($5000). It has been found during the years that this law has been in effect, that a number of the larger employers have been exempt from payment for from five to eight months per year, so that in some cases, even in coal nines, industrial insurance has cost less than 0.75 per cent.

Jan 3, 1919

By Wilbert G. McBride

Two Also 3 1/2-ton motor trucks were used by Young Bros. while operating at the Mammoth Collins mine at Shultz, Ariz. One was equipped with an oil tank holding 1,075 gal. and was used for the transportation of "tops." The other was fitted with a stake body and used to carry machinery, wood, rails, pipe and all classes of miscellaneous supplies. The bodies were made of oak with maple flooring and were attached to the frame of the chassis by U-bolts, to avoid drilling the main members of the frame. Most of the hauling was done from Tucson, a distance of 47 1/2 miles. During the first 3 months, part of the road was in very bad condition and the tire cost was excessive. After this part was repaired the road was in fair condition, but never good. There were no excessive grades or bad sand, but wagon ruts, too narrow for the truck wheels and of a different gage, caused heavy tire loss; while chuck holes, sharp curves and stones, both imbedded and loose, were objectionable features. During wet weather the trucks could not get sufficient traction to climb some of the hills and were likely to stick in the mud in certain places, so that no attempt was made to run them unless they were on the' road when the rain started. This lost time amounted to about 5 per cent. of the total, but, whenever possible, it was utilized in making minor repairs. The price of gasoline was from 17 to 21 c. per gal. Rubber tires were used throughout. Drivers were said $4.50 to $5 per shift, and a return trip to Tucson was counted as two shifts even when made in one day. Drivers were provided with a room in Tucson and were paid for a11 time lost due to causes beyond their control. Trucks were loaded one way only. Speedometers were placed on both trucks but the excessive vibration soon caused them to fail. For this reason, and because no account was taken of the distance covered in picking up a miscellaneous load or in other minor ways, the mileage given is under the actual distance traveled. Some of the weights had to be estimated, but care was taken to have the number of ton-miles low rather than high, to avoid underestimating the costs. The cost of hauling from Tucson to the mines was $12 per ton

Jan 1, 1917

By Henry Hebley

IN recent years, especially in the last decade, great interest has been shown and many advances have been made in the preparation and clean-ing of coal. In the major coal-producing countries, the percentage of tonnage cleaned has been increasing ever since 1924. As separating media, both liquids and gases are used, these generally being water and air respectively. Some systems, instead of obtaining separation by the velocity of the medium in which the coal is cleaned, depend on the density of water mixed with sand, or coal dust and shale, or with chemicals such as calcium chloride. In studying the results of coal-cleaning equipment, it will be observed that the efficiency of the cleaning apparatus lowers as the size of the coal decreases. This inability to obtain any marked improvement in the fines has been partly responsible for the installation of dedusting equipment, to remove the fine sizes from the raw coal prior to cleaning. When considering the possibility of installing dedusting equipment, many factors must be taken into account. Very often, but not always, both the ash and sulfur content of the coal increase as the coal size decreases. When bituminous coal, containing soft powdery fusain, is subjected to a wet washing process, the porous fines of the fusain remain in the small coal or in the wash water and delay the dewatering of the washed coal and increase the difficulty of clarification in settling tanks or thickeners. When a dedusted coal is cleaned by a wet process, the sludge recovered from the settling tank often runs so high in ash that the sludge can be discarded without further treatment and still the loss is small. Where treatment of the sludge is desired, however, froth flotation may be used to advantage if the size of the feed is below 1/10 in. Dust from the deduster can be treated in a similar manner. Fusain, which is usually found in the fine sizes, has often a much larger ash content than other coal.

Jan 1, 1933

By M. G. Corson

UNTIL recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast state, there is no reason for trying to establish precise data regard-ing the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing tempera-tures, so there is little incentive to study the properties of the cast shapes -cakes, bars, ingots and billets-for-the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This led to four investigations: by E. Seidl and E. Schiebold,1 by P. Siebe,2 by O. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence .of a wide zone of columnar crystals between the thin layer of fine crystals near the surfaces of the bars and the large but more nearly equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the casting machine. More recently, cast shapes of copper were investigated by N. P. Allen5 and by C. Blazey.6 Allen examined vertically cast wirebars and hori-zontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity clue to cold-work and anneal, but gave introductively an account of the composi-tion and average densities of the tough-pitch horizontally cast wirebars used. As far as the present writer can tell, no investigation was under-taken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, tough-pitch or otherwise.

Jan 1, 1938