Search Documents

By M. A. Grossman

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of unhardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of o.-2o per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as would appear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.2o per cent Mo provides a factor of 1.63, an increase of over 6o per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater harden ability will be obtained by using, for example, o.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By K. Torssell, U. Lindborg

The kinetics of precipitation deoxidation is considered from a theoretical point of view. The size distribution and the total content of deoxidation products are estimated statistically as a function of time, taking into account Stokes and gradient collisions between the particles and separation at the top surface of the bath. The assumption is made that two particles coalesce into one larger particle as a result of a collision. General expressions are derived and calculations are carried out numerically for the case of silica particles in liquid iron. The analysis predicts a three-stage behavior for the removal of oxygen, an incubation stage, a stage of rapid separation, and a slow final stage where the content approaches the equilibrium value. The agreement with experimentally determined size distributions and deoxidation times is considered to be good. A quantitative estimation of such growth mechanisms as diffusion from the melt and redistribution of oxygen from small particles to large ones shows that these latter mechanisms cannot explain the experimentally observed gvowth of inclusions. This also indicates that collisions provide the important growth mechanism. OXIDE inclusions precipitate when a deoxidizer like silicon or aluminum is added to a steel bath. The inclusions grow and the large particles tend to separate from the bath. For each type of oxide the growth determines the sizes of the final inclusions as well as the total inclusion content of the steel. The mechanism of growth is controversial, however. It has been suggested that an inclusion grows principally by diffusion of atoms through the melt to the inclusion particle or principally by collisions and coalescence with other inclusions. Diffusion growth is always present to some extent but recent experiments and calculations by Torssell,' Kniippel et 'a1.,2 Sano et al. and Miya-shita4 indicate that collisions may be more important than previously realized. A detailed analysis has so far been lacking. The present paper is a quantitative, statistical analysis of the growth and separation of inclusions and is based on a collision theory. Nuclea-tion is not considered. The numerical estimates are based on the experimental conditions of Torssell's' investigation and comparisons are made with his observations. Torssell' studied the growth and separation of silica particles in liquid iron. Samples were taken from a 0.6 kg iron bath at various times after the addition of silicon. By a particle-counting technique developed by Bergh and Lindber~the size distribution of the inclu- sions was determined. The number of particles at the first sampling, 10 sec after silicon addition, was of the order of 3 x lo7 to 10' per cu cm, the largest particles having a radius of 2 to 4 pm. The volume fraction was 0.001 to 0.004; i.e., the dispersion was very dilute. During subsequent holding the largest particles increased their radius by a factor of 10 after about a minute, and the whole size distribution was displaced toward larger values. These results were obtained with allowance for precipitation of the equilibrium concentration of oxygen during solidification. The bath contained less than 0.01 pct of C. Figs. 1 and 2 show the typical appearance of the inclusions. Most particles are very closely spherical and appear to have been liquid or semiliquid in the melt. The observed number of inclusions, about 5x 10' per cu cm, is of the same order of magnitude as found by ~er~h.' This is a large value. It follows that the diffusion distances are very short and that the precipitation

Jan 1, 1969

By W. E. Bron, E. S. Machlin

GRAIN boundary migration in V-shaped thin specimens of high purity silver was studied. Each specimen contained two crystals having the relative orientation: (111)A/(111)B; (ll0)A/(101)B. The boundary between these two crystals varied between a continuous curved and an alternating two plane interface. The plane interfaces were oriented parallel to (101)A/(011B) and (121)A/(211)B. Traces of these planes are shown in Fig. 1. Evidently the two plane interface, although of higher area, comprises lower total interface energy than the average curved boundary it replaced. The plane boundaries were found to move at 650 °C to consume the broad segment of the V opposite to the direction of interface area and energy decrease. On investigation, using the thermal etching technique of Hendrickson and Machlin,1 it was found that the outer grain contained 8.3x108 more dislocations per cm" than the grain at the apex of the V. Consequently, the boundary moved to decrease the strain energy associated with the difference in dislocation density across the boundary. The rates of motion of specific {110} and {112} boundaries were measured during interrupted anneals at 650°C by referring the position of the boundaries to each other and a fiducial line on the specimen surface. The measured rates of motion are 0.075 and 0.025 mm per hr for the {110} and {112} boundaries, respectively. Plots of grain boundary motion vs time of annealing show straight lines with little deviation of data points from these lines.

Jan 1, 1957

By F. W. Glaser

Metal-carbon-boron powder mixtures were hot pressed and the resulting specimens were studied by X-ray diffraction. It was found that regardless of the starting combination of the metal, carbon, or boron powders, a metal boride phase was always the major component in these samples. In the absence of carbon the boride phase formed on hot pressing depended only on the amount of boron present. Two new phases of the system Ti-B were found. They are Ti2B and Ti2B5. The existence of a controversial face-centered cubic phase of formula TiB was confirmed. Electrical resistivities were measured for various boride phases. It was found that the diborides are generally better conductors than the monoborides of the same metal. THE carbides and borides of the transition elements have very high melting points, in the range 2500° to 4000°C, and are therefore of interest as high temperature materials. The literature on the stability or chemical reactivity of these carbides and borides is very scarce. Various investigators'-" have demonstrated a relative instability of certain carbide phases in the presence of boron or boron-containing substances. In a recent publication, Glaserl demonstrated the stability of zirconium-boride (ZrB,) in the presence of carbon at temperatures in excess of approximately 2900°C, while during a preliminary investigation of boride phases, Steinitz' concluded that the diborides are stable in the presence of carbon while the monoborides of the fourth and fifth group are not, forming diborides plus carbides instead. Nelson, Willmore, and Womeldorph" have elaborated on the reaction B,C + 2TiC = 2TiB, + 3C, which was known to occur because of a relative instability of B,C and the great tendency towards TiB, formation at relatively low temperatures (approximately 1200°C). A similar study, involving as starting materials TiO, and B,C and resulting in TiB,, was recently described by Honak4, who observed the beginning of an exothermic reaction of a Ti0,-B,C powder mixture, which, when preheated in a hydrogen atmosphere to approximately 950°C, was carried to about 1600 °C by the heat of reaction. To shed more light on reactions of this type (Metal-C-B), the final product apparently always resulting in a boride phase at the expense of a carbide phase," a systematic investigation was started * Boride phases of various metals, as reported to date, are listed in Table I. and the following is an account of some of the results that were obtained. Materials, Preparation of Samples, Testing Methods The raw materials employed for this work consisted of various carbide, boride, and metal powders. as well as of boron and graphite powders. In cases where commercial grades of carbides were considered unsuitable because of low purity or excessive amounts of graphitic carbon, such carbide powders were prepared by this laboratory. The procedure for the preparation of carbide powders (zirconium carbide, titanium carbide, tantalum carbide, and niobium carbide) consisted of mixing graphite and the respective metal hydride powders in stoichio-metric proportions and subsequent heating of such mixtures in a hydrogen atmosphere in carbon crucibles. The heating was by high frequency to temperatures ranging between 1700" and 2100°C. The resulting carbide was then comminuted and screened to the desired particle size. ZrB, and TiB, powders were produced by the electrolysis of fused salt baths, according to the method described by Andriex.. The borides of niobium, vanadium, tantalum, molybdenum, chro-ium, and iron were obtained by mixing the respective metal and boron powders in the desired proportions. Such metal-boron mixtures were heated in a high frequency furnace to form boride powders. For each metal-carbon-boron group (Tables I1 through XI) a metal, its hydride, carbide or boride were mixed with carbon, boron or boron carbide powders. The additions of carbon, boron or boron carbide powders to any of these metals or metal compounds were calculated to satisfy a particular carbide or boride phase that according to the literature (Table I) had definitely been established by X-ray diffraction work. Samples of powder mixtures were hot pressed in graphite molds that were heated by direct conduction. The specimen dimensions were approximately 2.5X1X1 cm. Hot pressing temperatures were measured optically and maintained for approximately 30 sec under a constant pressure of about 1.3 ton per sq in. Wherever possible, an attempt to obtain maximum specimen density was made by temperature variation. Electrical resistivity testing was done by measuring potentiometrically the voltage drop over a length of 1.5 cm for a current of 10 amp, at room temperature. To obtain electrical resistivities for specific carbide or boride phases, values were plotted as a function of the respective sample densities

Jan 1, 1953

By L. O. Storey

The McDermitt mine was found as a separate mercury ore-bearing occurrence approximately 305 m (1000 ft) northeasterly and in a different geologic setting from the old Cordero mine, which had been the district's major producer. The following briefly describes the discovery of the new deposit and the Placer Amex lnc. involvement. The Cordero mining property was under lease by Sierra Mineral Management from the owner Fred H. Lenway in February 1971, when the property was brought to the attention of Placer Amex Inc. (known at that time as American Exploration and Mining Co.) by Richard F. Hewlett of Sierra Mineral Management. The property was first examined by Amex geologists in the spring of 1971, who reported favorably on the project. During that year, Sierra Minerals Management had retained Dr. Larry Walters as a consultant. He proceeded to drill test mercury soils anomalies which he had found northeast of the old Cordero mine in an area overlain by recent alluvium and gravel. An area known as the D area was subsequently blocked out and ascribed a tonnage of about 18 1 kt (200,000 st) which occurs in the vicinity of the eastern edge of the currently defined McDermitt ore body. This mineralization was found in flat lying mercury-bearing lakebeds, unlike the steep structurally controlled ore which was mined in the old Cordero mine. It became apparent to Placer Amex that since the chances of much more extensive ore were good in such a geologic environment, additional exploration was warranted. A joint venture was formed in October 1972 by American Exploration and Mining Co. and Sierra Mineral Management to further explore the Cordero property. The project exploration was fully funded and managed by Amex. Sampling began by Placer Amex in the D area where an open trench had exposed the lakebed ore. Visible cinnabar could not account for the high-grade mercury assays taken from the trench, and an unknown mercury mineral was suspected. Subsequent work established the presence of a chlorine-bearing mercury sulfide which may have enriched the lakebeds as a secondary supergene mineral. Early identification of the mercury-bearing mineral corderoite (Hg3Cl2S,) aided in the geologic concepts for the ore occurrence and was helpful in exploring for the expansion of the D area. Corderoite was found occurring with cinnabar in the lakebeds, and in places it is a major contributor. Specimens of the unique ore were given to Dr. Eugene E. Foord and Dr. Pieter Berendsen at Stanford University, who subsequently identified the chemical and crystallographic makeup of the new mineral and described it for the first time as a naturally occurring substance. Metallurgical work on mercury recovery from the newly described mineral was carried out by the Placer Development Ltd. laboratories in Vancouver, and an acceptable recovery system was worked out together with a planned mill design. Step out drilling from the D area by Placer Amex Inc. encountered extensive flat lying lakebed ore. The McDermitt ore body, as subsequently defined by drilling, was found to contain 2.7 Mt (3 million st) of open pittable ore, containing approximately 5 kg/t (10 lb per st) Hg. The ore body gently dips to the north and is found lying mainly in claybeds just above an opalite breccia blanket which overlies the earlier volcanics. Some ore is also found in the opalite breccia. The mine and mill were constructed under an operating joint venture with Placer Amex Inc. and Sterling Mineral Ventures, and production began in June 1975 at the rate of 20,000 flasks per year. The mine is currently in progress.

Jan 1, 1985

By G. K. Burgess

THE question of the allotropy of iron, in spite of a vast amount of experimental work and perhaps an even greater amount of theorizing, is not yet settled. That there is a definite transformation in iron near 900,° the A3 point, is generally recognized, as well as the fact that the temperature of this transformation is lowered by the addition of carbon and metallic elements. On heating, the transformation Ac3 is always found at a higher temperature than the transformation on cooling, Ar3. Whether the A3 transformation is sharp like the melting point of a pure substance, or extends over a considerable range of temperatures, embracing perhaps as a lower limit the A2 change, appears to be still an open question for pure iron. The nature and identity of the A2 transformation, it would appear from recent publications, has not yet been satisfactorily settled. In the present paper a critical, historical summary is given of the experimental investigations of the location of A2 and A.3 in pure iron, together with brief mention of some of the theoretical aspects of the subject, and an account is given of a series ?of experiments carried out with several samples of very pure iron which were studied by two methods of thermal analysis in the range from 5000 C. to 1,000° C., and which it is believed furnish a contribution of considerable interest as to the location and nature of the A3 and A2 transformations. Great attention has been given to the details of experimental manipulation and to the preparation of the samples, as it was soon found that some of the discrepancies noted in the work of many experimenters may be traced largely to lack of precautions which we have found essential. For example, to anticipate somewhat, it is necessary to provide a suitable practically gas-free furnace, the heating and cooling of which may be regulated to a nicety. To render a minimum the deforming effects on the cooling and heating curves of the poor conduction of the sample, it must be of a form and mass to pass on its heat rapidly and completely to the thermocouple; and finally the sample itself must be freed from gases which, if present, further mask the definiteness of the heating and cooling curves. We, have also varied within wide limits the several factors which may influence the determination of the exact location and shape of the transformation ranges, especially the mass and preparation of sample, rate of heating and cooling, design of furnace; and finally, as nearly as it is experimentally possible, we have worked with a substance approaching pure iron, free from occluded gases and other impurities, and contained within a vacuum.

Jan 10, 1913

Jan 1, 1920

By W. S. Sanner

Experiments were conducted to determine the quantity and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. A low, a medium, and a high-volatile anthracite were studied. Specific gravity separation followed by grinding, screening, and refloating at lighter specific gravities yielded small quantities of material purified to 1.0% ash, as follows: from low-volatile anthracite, 0.7%; from medium-volatile coal, 1.0%; and from high-volatile coal, 2.3%. The reduction in ash had no appreciable effect on the volatile matter or sulfur content of the coal. The limited quantities of material containing 1.0% or less ash obtainable indicate that if ultraclean coal is desired, a practical approach should include the processing units as an integral part of a convc.ntiona1 dense-media washing plant. Anthracite preparation practices during much of the industry's history were geared to maximum recovery of the larger sizes, pea through egg, which were used in hand-fired, domestic furnaces. Those sizes were cleaned to meet trade requirements, and the smaller sizes were usually higher in ash content. The impression, thus, was that ash content of anthracite always increased as the sizes got smaller. It was presumed that it was impossible to wash the finer sizes to extremely low ash contents. Following World War 11, the classical domestic market began to decline and the finer sizes assumed an increasingly large share of the market. For example, in 1949l 61% of the production was still pea and larger. Fig. l2 shows that -by 1955 these sizes accounted for only 50%, and in 1965, they were only 39% of the total anthracite produced. With the reduction in the market, increased quality was demanded, especially in export markets, and an increasing number of dense-media magnetite washers were installed in new and existing cleaning plants. In 1965, the coarse coal prepared at 59 breakers in the anthracite fields was sampled by the U.S. Bureau of Mines (USBM); approximately 50% of these plants were equipped with dense-media magnetite washers.3 Since 1950, more attention has been focused on the use of finer sizes for numerous industrial uses, including iron-ore sintering, pelletizing, foundry coke-making, cement manufacture, production of calcium carbide, and of carbon electrodes, etc. Most industrial uses require relatively clean anthracite, such as 10 to 11% ash for sintering and foundry coke, 7% for aluminum melting-pot cathode carbon, and 5% for carbide production. Hence, cleaning methods have been improved to the extent that dense-media washers, hydraulic cyclones, and flotation cells have been introduced as fine-coal-cleaning devices. It is now possible to wash the buckwheat, rice, and barley sizes (9116 X 3132-in.) to ash contents as low as 8 to 10% in dense-media devices, but washing the -3132-in. sizes to those limits presents more difficult problems, due mainly to the fineness of the material. This USBM investigation was conducted to determine the amount and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. The goal was to reduce the ash content to a level acceptable for industrial carbon uses, including electrode manufacture, which generally requires an ash content of 1% or less. While low-ash content is of primary importance in selecting industrial carbons, the amounts of other constituents are also important, including iron, silicon, titanium, nickel, vanadium, and sulfur. They were not considered in this work, since their occurrence in deashed anthracite has been studied elsewhere.4 The results of the present investigation were used to design a flowsheet, suggesting a method for producing ultraclean anthracite as part of conventional preparation practice, using dense-media vessels, crushers, pulverizers,

Jan 1, 1970

By A. K. Csazar, L. W. Holm

This paper describes our investigation of a post-water-flood, oil recovery process which consists of injecting a slug of propane followed by water. Also described are the results obtained by applying a modification of the process in which gas was injected ahead of the water. Under the conditions of the latter experiments, misci-bility was not achieved between the propane and gas. Preliminary experiments or) uniform, watered-out sandstone cores showed that an oil bank could be formed and produced by applying this recovery process. However, since reservoirs are not uniform in structure, the process also was applied to porous media containing irregular porosity and to stratified sand systems. As a supplenzerrt to the experinlental work, a mathernatical procedure was developed for calculating the performance of the recovery process in a bounded, layered, porous system with crossflow between layers. As a specific example, the method was applied to predict the perforrnance of the recovery process in a 6-ft long, two-layer, stratified, unconsolidated sand model for comparison with experinlental data. The calculations were programed for the ZBM 704 computer. The equations and calcula-tional procedure presented can be extended to systems containing any number of randomly distributed permeability variations or any number of parallel layers. INTRODUCTION The problem of recovering the oil that remains in a reservoir which has been waterflooded is receiving considerable attention now as an increasing number of water floods reach an economic limit. A large number of the waterflood projects are in shallow reservoirs which are at pressures below 1,000 psi. It has been demonstrated in the laboratory that post-waterflood oil can be recover-ered by miscible displacement, but the LPG-gas, miscible flood and the enriched gas drive cannot be applied effectively at pressures below 1,000 psi. Only a few reports have appeared in the literature2-4 on low pressure, partially miscible recovery methods. However, it is possible to use LPG in a partially miscible displacement process in a reservoir where pressures of 200 to 1,000 psi can be achieved. Under these Pressures and at normal reservoir temperatures, propane is miscible with the oil; but, of course, gas or water used to drive the propane slug would not be miscible with the propane. Because of the lack of complete miscibility, it has generally been concluded that excessive amounts of propane would be required to recover oil and that such a recovery method would not be economical; however, we have found that under conditions present in certain reservoirs, an imrniscible recovery process can be applied effectively. The oil saturation in reservoirs at the economic limit of waterflood projects is usually in the range of 20 to 35 per cent of the pore space." A certain portion of this oil is left trapped by water in various size pores of the rock, but a good part of this so-called "residual" oil can be present in the less permeable lenses or layers of the reservoir rock which were by-passed to some degree by the water. The oil in these permeability traps can be produced only if favorable pressure gradients are formed in the reservoirs between adjacent zones of high and low permeabilities. A low viscosity liquid, miscible with the oil in place, which is driven by water through a stratified or heterogeneous porous system can aid in the development of these favorable pressure gradients. The oil that is released thereby from the permeability traps can be recovered by the subsequent water flood. Studies were made to determine how much oil could be recovered from homogeneous and stratified cores and models, which had been water flooded, by injecting a slug of propane and driving it with water. The effect of injecting a slug of gas ahead of the water was also determined. Most of the work described herein was done with the propane-water combination; unless otherwise specified, no gas was injected. The principal objectives of the investigation were to determine (1) if an oil bank could be formed and (2) what ratio of oil recovered to propane injected would be obtained. A further objective was to develop a method for calculating fluid-flow performance in stratified systems which would account for fluid transfer between zones in hydrodynamic communication but of different permeabilities. THEORETICAL ANALYSIS In a theoretical study of the recovery process, analytical expressions were derived to calculate the pressure distribution, the fluid flux in longitudinal (parallel to layers) and transversal (across the layers) directions, and the fluid distribution at any point in the system. The equations were developed for a two-layer porous system in which it was assumed that the fluids in the system were incompressible and that capillary and gravity effects were

On the following pages are abstracts of papers published by the Institute during the year 1932 as Technical Publications, Preprints, in bound volumes and in Mining and Metallurgy. For abstracts of papers that appear in bound volumes in 1932 but that were published as Technical Publications in 1930 or 1931, see the Transactions for those years. Papers that appear in this volume are not abstracted here. Many of the Technical Publications have been reprinted in bound volumes. Information regarding this disposition, and number of pages in each paper, may be found in the list beginning on page 309. Volume numbers are given as listed on page 3 and in the paragraph at the beginning of the index, page 315. The abstracts are grouped as follows: Page Page Metal Mining.................... 265 ferrous Alloys)................. 279 Milling and Concentration......... 268 Coal Division.................... 287 Iron and Steel Division............ 270 Petroleum Division............... 292 Nonferrous Metallurgy (Reduction Nonmetallic Minerals............. 299 of Ores)....................... 277 Mining Geology.................. 301 Rare Minerals and Metals......... 279 Mining Administration (Accounting, Institute of Metals Division (Found- Taxation, Industrial Relations). . 304 ing and Metallography of Non- Geophysical Prospecting........... 304 Metal Mining The Mineral Industry. By Scott Turner. (Min. & Met., June, 265. 3500 words.) Abstract of an address delivered before the Royal Canadian Institute, Toronto, April 16, briefly outlining the importance of mining in the United States, in Canada, and in the world. Comparison is made of the mineral production for 1886, 1900, 1910, 1920 and 1929, showing that in the 43 years from 1886 to 1929 that of the world increased nearly tenfold, of the United States over twelvefold and of Canada thirtyfold, but that Canada's output was equivalent to only 2 per cent of the world total and to 5 per cent of that of the United States in 1929. Statistical tables and graphs show value of production, percentage of world production contributed by Canada and the United States, etc. The mining situation in Canada is briefly reviewed: only those American engineers who have had occasion to examine the figures appreciate the rapidity of growth of Canadian mineral production. The treatment of minerals involves vast complex industries. When we are producing, say, 6 billion annually, the employment of 2 million workers provides indirect support to perhaps 10 million people. Exploiting mineral deposits is peculiar in certain ways, for the deposits are exhaustible, are of rare occurrence when measured in terms of outcrop area compared to total earth area, and may suddenly be handicapped or superseded by new discoveries; moreover, the economic position of the contained metals is 'affected by the use of scrap metal and the existence of invisible stocks. The largest and most valuable of the mineral deposits are not the metals, but rather the fuels. The record of the coal industry in recent years is one of brilliant technical achievement; its economic position is far from satisfactory. A so-called world fuel

Jan 1, 1932

By D. H. Gieskieng

THE advent of curved jaw crusher wearing plates made an approach other than segmental layout analysis desirable for prediction of capacities. For some time it had been known that the drawing board capacities of crushers using these plates had to be considerably modified by complicated experience factors to achieve agreement with results. Because these apparent capacities could be readily increased severalfold by minor crushing chamber shape changes, it was necessary that the utmost precaution be taken in predicting capacities of jaw plates modified for nonchoking, special wear characteristics, or any other reason. To this end the laboratory and field tests outlined by the author in a previous paper1 were made on Blake-type jaw crushers. The results of these tests were summarized in a simple first degree equation applicable to crushers using either straight or curved jaw plates. This equation first outlines the maximum capacity potential of a given crusher, then reduces this figure in accordance with installation circumstances by means of a realization factor. It was found subsequently that this equation, with the addition of an eccentric throw factor, is applicable to standard types of single-toggle or overhead eccentric jaw crushers as far as maximum capacity potential is concerned. However, these crushers have realization factor curves somewhat different from those outlined for the Blake type. While this paper is concerned principally with standard type single-toggle crusher capacities, the evaluation of data obtained with these machines is simplified by comparative reduction to the 10 x 7 in. Blake-type equivalents upon which the summary of the preceding paper was made. Convertibility of data from one type of crusher to the other also tends towards confirmation of both. The agreement of these data is sufficient to be considered complimentary. Consequently the feed factors, f, previously reported for Blake crushers are slightly adjusted to an average with the single-toggle crusher results. Blake-type equation: C = f.d.w.y.t.n.a.r [I] Single-toggle type equation: C = f.d.w.y.t.n.a.e.r [21 where C is the capacity in short tons per hour through the crusher, f is a feed factor, dependent upon the presence of fines in the feed, and the surface character of the jaw plates used. Values of f : Smooth Plates Corrugated Plates With normal fines 0.0000414 0.0000319 Fines scalped out 0.0000368 0.0000252 Large pieces only . 0.0000312 0.0000215 d is the apparent density of the broken product in pounds per cubic foot. (If the true specific gravity of the feed is known, 40 pct voids may be assumed and d becomes 37.4 times sp gr). w is the width of crushing chamber in inches. y is the openside setting of the crusher, in inches. In the case of corrugated jaw plates it is measured from the tip of one corrugation to the bottom of the valley opposite. t is the length of jaw stroke in inches at the bottom of the crushing chamber. It is the difference between open and close-side settings. n is rpm, or crushing cycles per minute, a is the nip-angle factor. It is unity for 26" and 3 pct greater for each less nip-angle degree. A nip-angle of 20" has an a value of 1.18, and an angle of 30" has an a value of 0.88, see Fig. 1. r is the realization factor. It is unity for perfectly uniform choke feeding and usually less for actual operating conditions according to the method of feeding used and the probabilities of hang-ups involving the size of feed and crusher opening. Approximate values are given by the curves in Fig. 2. These values are further reduced by intermittent feeding, e is the throw or diameter of gyration of the single-toggle crusher eccentric in inches. As evident in Fig. 1A, variation of feed size will generally have little effect on nip-angle if both jaw plates have flat areas. Jaw plates having continuous curvature, as in Fig. 1B will have different nip-angles, depending upon the size of feed. For test work as described in this paper this effect was accounted. For general compilation of capacities for average feeds it is suggested that the nip-angle be taken at the various settings computed, at an arbitrary level, such as is indicated in Fig. 1C. Data Evaluation To bring the Blake and single-toggle type crusher capacity test results to common terms for evaluation, all data are converted to terms of 10 x 7 in. Blake-type performance at conditions of 100 lb per cu ft, 10 in. chamber width, 250 rpm, 0.65 in. stroke, 3-in. openside setting, and 18° nip-angle. (The nip-angle of the 10x7 in. Blake is 18° at 3-in. setting.) The single-toggle crusher performances are also divided by the eccentric throw to bring this effect to unity. As outlined,' laboratory and field tests made on Blake-type crushers ranging from 10 x 7 in. to 60 x 48 in. were summarized along the foregoing conditions of speed, stroke, etc. This resulted in groups of data which correspond to feeds with fines, feeds

Jan 1, 1952

By Halbert Powers Gillette

In every chemical reaction heat is either developed or absorbed, and this plus or minus heat of formation is as definite in quantity as the weights of the reacting elements. In this paper I shall show that each chemical element and each chemical radical has its own definite heat-valency,—a fact which, so far as I know, has hitherto escaped the attention of investigators, but, I feel sure, will be admitted after the demonstration here given, and may lead to some practical conclusions of value. When Berthelotys " law of maximum work " was found to have so many inexplicable exceptions, the pendulum of a scientific theory swung away from a recognition of the truth underlying that proposition; and this reaction went so far that not only has thermal chemistry been relatively neglected by recent investigators, but it is not uncommon now to find textbooks on physical chemistry which practically ignore all that Thomsen, Berthelot and others have done. To this temporary tendency of thought I attribute the failure to recognize the principles herein announced and explained. Not long ago, while studying tables of the formation-heat of various salts, I noticed that in this respect all potassium salts in solution differ from the corresponding sodium salts by 9.3 cal.1 I found also that similar differences exist between other salts, not only when the basic radical is varied, while the acid radical remains constant, but also when the acid radical is the variable. Thus chlorine salts in solution differ from bromine salts in this respect by 10.9 cal. Upon further study, I found that Thomsen had noted similar constant differences, but, so far as I can ascertain, he appears to have attached no great significance thereto.

Jan 1, 1904

By J. L. Gillson

Historically, rock deposits and sand deposits of titanium minerals came into production about the same time, although there may be some argument as to what is meant by production. Beach deposits of heavy minerals in India (Figs. 1-4) and Brazil (Figs. 5) were worked for monazite about the turn of century, but as there was then no market for titanium minerals, these were thrown away. The rock rutile deposits at Roseland, Va., Fig. 6, were worked to supply rutile for titanium chemicals and for coloring ceramics long before there was a titanium pigment business. The pigment industry started about the middle twenties, both in Europe and the U. S., and almost simultaneously the rock deposits at Ponte Vedra Beach near Jacksonville, Fla., were worked for titanium content. Since those days, production from both types of deposits has continued to grow at a rapid rate; many deposits of both types have been found, and reserves have grown to very large figures. In total tonnage of reserves, there is no doubt that the rock deposits are far ahead of the sand deposits; nevertheless there is a very large tonnage of commercial sands available. It is the quality of titanium mineral in the sand and the relatively lower costs of operating sand deposits that have kept them abreast, at least in annual tonnage produced, with the rock deposits. The principal titanium mineral used is ilmenite, but as soon as that mineral began to be sought as a titanium ore, it was obvious that there are ilmenites and ilmenites. Textbook ilmenite should have the composition FeOTiO2 and should analyze 52.6 pct TiO2 and 36.8 pct iron as Fe. The Indian ilmenite, for almost a generation the standard ore for manufacturing pigment in the U. S., was found to analyze about 60 pct TiO, and only 24 pct. Fe, and most of the iron is in the ferric condition. The whole process of pigment manufacture in the U. S. was built up on the use of a raw material of that grade, and the American chemical engineers who operate the pigment plants shuddered at the thought of using a rock ilmenite with 45 pct or so of TiO, and nearly 40 pct Fe. Intensive search was made around the world to find other deposits of rich black sand, like the Indian beaches, but although a few were found, there was some objectionable feature about each. A deposit in Senegal, south of Dakar (Fig. 7), was worked for a while, but an organic coating on the grains made attack by acid difficult. Modern practice would have included a scrubbing operation, in a caustic soda bath, to eliminate the organic coating. Brazilian deposits were numerous, but individually small, and shipping from them difficult. Deposits on the east coast of Ceylon had many attractive features, but the ilmenite analyzed only 54 pct TiO2 and could have been used only with a penalty. Sand deposits with 2 pct ilmenite, like those now worked in Florida, would not have been considered commercial ore, even if they had been known at that time. Most rock ilmenites are associated or mixed with hematite or magnetite, which accounts for the lower titanium and higher iron values than in the sand ilmenites. The Norwegians, English, and Germans, with cheap Norwegian rock ore at hand, learned to install in their pigment plants adequate capacity on the black side, as it is calltd, and counterbalanced the extra cost of plant, and larger amount of acid used, by the lower cost of ore. When World War II arrived, two of the largest pigment manufacturers in the U. S. had to learn how to use the Adirondack ilmenite, but one of them very gladly went back to sand ores when the Florida deposits came into large-scale production after the war. The other continues to use Adirondack ilmenite and finds it commercially attractive to do so. Rutile is not a raw material for titanium pigment manufacture by the sulfate process, since it is insoluble in sulfuric acid. In addition to its small consumption in chemicals and ceramics it began to be used in quantity in welding rod coatings. With the outbreak of World War 11, and the tremendous need for welding rods in shipbuilding and other structural steel construction, rutile suddenly became in heavy demand. The sand deposits on the eastern shore of Australia (Fig. 8A) which had been worked in a small way since 1934 were brought into production, and some stream placers in Brazil were worked and rutile concentrates shipped to American

Jan 1, 1960

By R. G. Ward, A. E. El-Mehairy

A technique was developed to calculate the density of liquid metals from the profile of a weighed levitated drop obtained by emitted light photography and calibration. The density of liquid copper was determined over the temperature range 1370" to 2100°K and expressed with the equation: The molar volumes and thermal coefficients of expansion are calculated. Copper, upon melting, was found to expand 3.34 pct. A knowledge of the density of liquid metals is essential as it is a parameter appearing in most theories of the liquid state. The liquid density is also necessary for the calculation of the commercially important contraction occurring on solidification. Unfortunately good density values are rarely available and the present work was undertaken to establish a new method of density determination free from the limitations of the existing methods. For liquid metals with high melting points, the variation and the limited number of density values reported in the literature have been caused primarily by difficulties in technique, a matter which has been adequately discussed by Urbain.' In all the methods used for measuring the density of the high-melting liquid metals there are sources of error, and corrections have to be made. For example, in the method of balanced columns, the formation of gas bubbles in one or both arms was a great source of error. In the pyknometer3 and immersed-sinker methods, corrections of certain volumes for thermal expansion to the operating temperature exceed 4 pct. In the maximum-bubble method5 a correction for the thermal expansion of the bubble-tube is used (about 1.6 pct); a second correction takes into account the change in the volume of liquid displaced by the bubble-tube (about 3.5 pct). Another method used is based on the shape of a drop of liquid, at rest on an inert refractory plaque, obtained photographically or radiographi-cally. The volume is calculated from the shape, which is sensitive to the surface tension and supporting material, by some intricate empirical relation. The drop contour changes with 90 deg rotation of the support.7 The application of all methods is limited by reaction between liquid metal and the apparatus. The successful stabilization of a mass of liquid metal during levitation melting8 afforded a technique for measuring the density of liquid metals out of contact with solid materials. The technique was developed by using copper as the density of liquid copper has already been studied extensively, thus allowing comparison with the new method. It consists of calculating the volume from the dimensioned profile of the levitated drop obtained by emitted-light photography and careful calibration. The molten egg-shaped drop spins around the magnetic axis of the coil (lined vertically) at a speed which seems to increase with increasing temperature. The method does not involve corrections and the experimental setup allows the use of vacuum or special atmospheres. The maximum operating temperature is limited by excessive evaporation of metal from the droplet. EXPERIMENTAL Levitating System. A stabilizing ring was used in conjunction with a 3-turn levitating coil energized by a 450-kc per sec, 10-kw Toccotron with a high current-low voltage output stabilized to f 1 pet.' APyrex glass tube with a Pyrex Optical flat window inserted through the coil and ring allowed the use of special atmospheres during levitation melting, as shown in Fig. 1. Optical System. Fig. 1 shows the optical arrangement used to photograph the profiles of the drop, parallel and perpendicular to the vertical spinning axis, simultaneously on the same frame of a high-speed 35-mm film. The optical system was adjusted to avoid any distortion of the profiles and to ensure that both profiles are in focus. The length of path from object to objective was about 30 cm, and a magnification factor close to 1 was obtained with the single-lens reflex-camera system. Temperature Measurement and Control. In operation, the specimen temperature was constant to 5 C for a fixed power input to the levitating coil and fixed rate of gas flow through the tube. The temperature was measured by an automatic two-color pyrometer (Coloratio) checked at the melting

Jan 1, 1963

By Cyril Smith

SOMEWHAT over ten years ago the author described studies1,2 on the constitution of the copper-silicon system. The copper-rich portion of this diagram is shown in Fig. 1. The experimental points freely dotted about the diagram seemed to justify an otherwise unconvincing diagram and for several years the curious reverse bend in the alpha-phase bound-ary was accepted as substantially correct, even by later investigators3,4 of the system who introduced changes in the high-silicon phases. The binary diagram has been used as a base for several ternary systems" without any suggested changes. Voce10 suspected the existence of another phase from his study of the cast alloys in the copper-manganese¬silicon system, but evidently hesitated to extrapolate this to the binary diagram, particularly in view of the too ingenious explanation that was advanced" to account for the pools of constituent clearly visible in castings; namely, that they were secondary alpha of twinned orientation deposited from beta. Von Schwarz,12 in 1932, called attention to the fact that this micro-constituent in copper-silicon alloy castings was anisotropic under polar-ized light and asserted that a new phase, not cubic, should be placed in the diagram adjacent to alpha. Sautner,13 on the basis of investigations with the polarizing microscope and with X-rays, introduced this phase into the diagram at about 6 per cent Si. The relevant part of his dia-gram is shown in Fig. 2. Sautner called the new phase beta, renaming the old beta phase zeta. To avoid confusion, in redrawing Fig. 2 the phases have been renamed in accordance with the terminology adopted in the present paper, in which the new phase is called kappa and the other phases retain the designation given them by Arrhenius and Westgren.4

Jan 1, 1939

By Edwin Ludlow

To THE members of the American Institute of Mining and? Metallurgical Engineers who were fortunate enough to be able to attend the Fiftieth Anniversary at Wilkes-Barre, it was brought home that commercial anthracite requires not only expensive mining but that the milling or preparation of it is also a costly operation, requiring very large capital expenditures and high maintenance and labor costs. The great trouble that coal men meet in discussions of coal problems today is the difficulty the average coal user, especially in the East, finds in distinguishing between anthracite and bituminous coals. They are two entirely separate problems and yet the people who are burning coal complain bitterly of the high cost of anthracite and quote the figures furnished in regard to the prices of bituminous coal and feel that the anthracite operators are making an excessive profit, without realizing the enormous difference in the cost of production in the two fields. The great difference that can be marked is that in this year of industrial depression the prices of anthracite have been not only maintained but have increased during the summer, while the price of bituminous coal has been continually dropping since the first of the year, and yet the same law of supply and demand governs both anthracite and bituminous. In order to understand the situation the two problems must be considered from their separate points of view.

Jan 1, 1921

By G. W. Ostroot, S. Shryock

Cementing deep, high-temperature oil wells where static temperatures range from 350 to 400F has become routine in the part decade. In the United States there were 271 wells drilled deeper than 15,000 ft during 1963. Many of these wells had static temperatures higher than 400F. Bottom-hole static temperatures near 700F are now realities in the geother-mal (steam producing) wells of California's Salton Sea area. The detailed planning initiated prior to drilling the wells is discussed together with the methods, materials and equipment used in solving the cementing problems which are encountered. Data are also presented that lead to development of cementing compositions that provide adequate thickening time, do not retrogress in strength, and maintain low permeability under these extreme temperature conditions. Field data include the cementing programs used on eight relatively trouble-free geothermal steam wells in the Salton Sea area. INTRODUCTION Not too many years ago cementing oil wells with temperatures in the range of 300F caused considerable anxiety. In some areas of the United States it is now fairly common to cement wells having bottom-hole static temperatures in excess of 400F. We are now confronted with the problem of cementing wells with temperatures ranging from 500 to 700F. Temperatures in this order of magnitude are often found in geothermal steam wells. From where does this extreme heat emanate? There are many theories as to the source of this steam flow. The most widely held views are: (1) heat- ing of ground water fairly close to the surface by an intrusive mass of hot rock; (2) steam generation from a reservoir of metamorphic rock, normally found below 25,000 ft and not at the shallower depths of the Salton Sea reservoir; and (3) high-temperature gases (water vapor) escaping and migrating from molten or semi-molten rock (magma) at a considerable depth. Of these. No. 3 seems to be the most generally acceptable explanation. Heat from springs and fumaroles has been used for years as a means of heating and cooking; however, significant progress in harnessing the vast power of underground steam reservoirs has been relatively slow. The first large-scale attempt to use the heat generated by steam from wells was made in Italy around the beginning of the 20th century. In excess of 250,000 kw of electrical power is now being produced from holes around Larde-rello, Italy. Another very active drilling program was initiated in the volcanic area of New Zealand in 1949.' Natural steam for power projects in the United States began in the early 1920's. An early commercial steam field is located at the Geysers, approximately 75 miles north of San Francisco, an area discovered in 1847 and used for many years as a health resort. Steam originates from 15 wells that have been drilled since 1957. The present output from this project is 25,000 kw. Success of the Geysers operation has been responsible for several companies taking a careful look at the feasibility of producing steam for power generation in the Salton Sea area of Southern California's Imperial Valley. Geothermal steam activity in this latter area began in 1961 when O'Neill, Ashmun and Hilliard completed Sportsman No. 1, at that time the hottest wellbore in the world.' Since its References given at end of paver. completion seven additional wells have been successfully completed in this area. Many problems encountered in drilling steam wells had to be overcome to make the ventures successful. Formation temperatures encountered in the Salton Sea seemed to be a straight-line function (a gradient of 13F per 100 ft of depth).' This imposed severe conditions on all aspects of drilling and completion. This varied, to some extent, from gradients in the older geothermal areas. Not to be overlooked is the effect of these temperatures on casing creep or elongation by thermal expansion (Table I), because standard API flanged wellhead equipment makes no provision for this kind of performance. Floating equipment was redesigned, and changes in types of downhole equipment were made in an effort to eliminate anticipated problems. In the later completed wells, standard oil-well cementing equipment has been used. During the early development of geothermal steam wells there were some problems resulting from blowouts. However, these were eliminated in the deeper Salton Sea wells and no problems were encountered with the drilling mud. A sodium surfactant mud was used on the Sportsman No. 1 to drill from 2,690 to total depth. Nevertheless, it was necessary that a cooling system be added and the mud cooled before circulating it back into the well. The difficulty in evaluating the size of the steam area and its potential in terms of pounds of steam and years of productivity still has not been resolved. Economic complexities have also entered into the steam play in the Salton Sea. The wells at the Geysers were drilled at a cost of $15,000 to $20,-000, whereas the Salton Sea wells will cost more than $150,000. This cost differential has to some extent been accounted for because of the heavily

Jan 1, 1965

By Francis M. Walters

THE problem of making iron-manganese alloys of scientific purity is a rather difficult one. They cannot be prepared in air because of the readiness with which the metals oxidize at the temperature of melting; and they cannot be prepared in vacuum because of the, high vapor pressure-of- manganese. The very property of: manganese which permits it to be purified interferes with the utilization of the best method of making pure alloys. Accordingly, it is necessary to use a gas atmosphere which will not affect the-properties of the alloys. The gases available for the purposes are hydrogen; helium and argon. Nitrogen forms intermetallic compounds with manganese very readily. Hydrogen, while valuable as a deoxidizer and having the advantage of being comparatively cheap, is explosive over a wide range and, has a rather high thermal conductivity. Helium is reported as, costing little but is difficult to secure at a reasonable price and also has a conductivity nearly as high as hydrogen. Since argon has a sufficiently low thermal conductivity, it has been selected for use in one induction furnace for melting, under a controlled, gas atmosphere, in spite of its cost, which is so high (70 cents to $1.50 per cubic foot) that it must be stored and purified.. Such a gas atmosphere-as argon makes necessary the use of the, high-frequency induction method of heating. This involves, a non-metallic container for the gas; .which is most conveniently of fused quartz or glass. The next

Jan 1, 1929

By Juan Sodi, John F. Elliott

The standard free energy of ReS2 has been measured in the range of 1050° to 1250°K using H2/H2S mixtures and a slight variation of the method described by Hager and Elliott.1 The result is: The experimental method and apparatus were modified slightly for this study. Measurements on Cu2S were made to verify the application of the method to the work on ReS2. THE EXPERIMENTS AND RESULTS Briefly, the experimental method consisted of exposing a chip of copper or rhenium at a known temperature for 8 hr to a slowly flowing gas stream at the same temperature in which Ph2S and PH2 were known. The chip was withdrawn quickly from the hot furnace, and subsequently it was inspected for the presence of a sulfided surface. In the experiments described here, there was no ambiguity in any case as to the presence or the absence of the sulfide. At a given temperature, gas compositions for sulfidization were explored systematically until two compositions were found whose values of ?G°, Eqs. [I] and [2], were within approximately 100 cal of each other, one of which was sulfi-dizing and the other was not. These are termed the "straddle" compositions and it is assumed that the equilibrium composition lies between them. The chief modification to the apparatus, which is shown schematically in Fig. 1 of Ref. 1, was to support the metal specimen on a small alumina boat which could be moved along the reaction tube, 6 mm ID, by platinum wires. An appropriate seal at each end of the reaction tube permitted the sample to be moved from the cold end of the tube into the hot zone in 2 to 3 sec, and the sample could be withdrawn equally rapidly. Thus, it was possible essentially to quench the specimen from the reaction temperature with the reaction gas or helium flowing and without danger of breaking the reaction tube. The usual practice at the end of the experiment was to switch the gas system to the helium tank, flood the reaction chamber with helium, and pull the sample out of the hot zone. The purpose of the modification was to permit study of the sulfidization of copper without the complication of the back-reaction between the gas and the specimen as the latter cooled during slow withdrawal of it from the hot zone; this was a problem in the earlier work.&apos; A further improvement located the tip of the temperature-indieating thermocouple and the specimen precisely at the hottest part of the furnace. A carefully calibrated thermocouple, with its tip at the position of the specimen and with other conditions duplicating those of an actual experiment, showed that in the temperature range of 900° to 1122°C the temperature of the specimen differed from that of the tip of the indicating thermocouple by less than 0.5°C. The two positions were 0.5 cm apart. The reaction gas was prepared from ultrahigh-purity hydrogen (<l ppm O2, <0.5 ppm H2O) and CP grade hydrogen sulfide (99.5 pct H2S). High-purity helium (99.995 pct He) was used. All of these gases were purchased from the Matheson Co. All flow meters were recalibrated by the soap-bubble method with hydrogen, H2S, helium, and several gas compositions used during the study. These calibrations gave a linear relationship with a slope of 1.0 for the plot of log flow rate vs log pressure drop across the flow meter, in accordance with the Hagen-Poiseuille equation. The analysis of the gas was determined in the same manner as was reported previously. Good checks were obtained between the composition of the gas established by the flow-meter settings and by chemical analysis of the gas taken after the mixing bulb and ahead of the furnace. The pressures of H2S, H2, S2, and HS in the equilibrium gas at temperature were calculated from the following data :3 The pressures of the species S and S8 were negligible for the conditions of the experiments.3 There was no sign of vaporization of ReS2 either by weight loss or deposits in the reaction tube. Thus it is not possible to account for the apparent volatility of the compound reported by Juza and Biltz.2 The inlet gas composition and the calculated equilibrium ratio of PH2 S/PH2 for the "straddle" points of each experiment are shown in Table I. The specimens of metal for the experiment were small clippings of annealed copper (99.9+ pct) sheet 0.005 in. thick that was obtained from Baker and Adamson and of "high-purity" rhenium (99.9+ pct) sheet 0.005 in. thick that was purchased from Chase Brass and Copper Co. A specimen was removed from the apparatus; inspected for the presence of the sulfide, and then stored in a sealed vial. A fresh clipping was used in each measurement. The condition of the surface of each specimen after the experiment is noted in Table I.

Jan 1, 1969

By H. H. Johnson, Eric W. Johnson

A newly developed ac technique was used to measure the electrical-resistivity changes associated with both cyclic stressing and subsequent annealing of high-purity and OFHC copper. The early stage of push-pull fatigue was explored at 293° and 4.2°K, with stresses chosen for an expected fatigue life of 2 to 8 X 105 cycles. For high-purity copper, fatigue at 293°K was accompanied by an initial increase in resistivity. After about 5000 stress cycles, no further increase was observed. Annealing studies showed that the resisticity increment could be accounted for solely in terms of an increased dislocation density, to about 2 x 1010 disl pev sq cm. Fov 42°K fatigue, however, the resistivity increased continually, with no evidence of saturation, as approximately (No. of stress cycles)1/4. This is intevpreted to result from both dislocation multiplication and vacancy production; estimated vacancy concentrations are 10-4 to 10-9. The continuous resistivity increase was inhibited by interspersed annealing treatments at 293°K, which also raised the level of the stress-strain curve. These effects are attributed to annealing of vacancies into dislocation loops. In contrast, OFHC copper fatigued at 4.2°K showed saturation of electrical vesistivity after only a few hundred cycles, and it appeared that vacancies annealed out completely between 77° and 293°K. MaNY observations suggest that both dislocation multiplication and point-defect production are important aspects of fatigue deformation. An increase in dislocation density with number of stress cycles has been demonstrated or implied by several experimental techniques, including optical metallography with lithium fluoride,&apos; electron microscopy with copper,2 thermal conductivity of Cu-Zn alloys,3 and peak-stress measurements during cycling at constant plastic strain amplitude.4,5 At low amplitudes and/or stresses saturation of fatigue hardening and dislocation density occurs early in the expected fatigue life,4-6 frequently by a few hundred cycles. The evidence for point-defect production is somewhat less extensive, but it is nonetheless persuasive. Rosenberg7 reported briefly that, for equal stresses, copper fatigued at liquid-hydrogen temperature displays an increase in electrical resistance some ten times that which accompanies unidirectional stressing. Further, the extra resistance saturates after a few hundred stress cycles, and does not anneal significantly until a temperature of about 170°K is attained.&apos; Point-defect production during fatigue is also suggested by 1) the softening during cyclic stressing of initially strain-hardened polycrystal-line copper9, 2) the strong temperature dependence of the yield strength of fatigue-hardened mono- and polycrystalline copper,579"0 and 3) the influence of intermediate annealing upon slip-band formation in copper fatigued at 90°K.8 It is evident that characterization of the fatigued state requires a knowledge of both point-defect and dislocation densities. For this purpose electrical-resistivity measurements are useful, but they are difficult to perform because of geometric limitations. Push-pull fatigue is necessary to obtain a macroscopic ally uniform deformation over the specimen cross section; however, the specimen must then have a low slenderness ratio to avoid plastic buckling, while the standard dc resistivity technique requires a very slender specimen for

Jan 1, 1965