Search Documents

By C. A. Hansen

Page Introduction............................206 Power Characteristics in Zinc Sulfate Electrolysis........... 207 Current Efficiency......................... 207 Corrosion Rates..........................216 Voltage Required by the Zinc Cell..................219 Power Requirements of the Zinc Cell ................221 Impurities in Zinc Electrolyte.....................222 Non-cumulative Impurities.....................223 Cumulative Impurities ....................226 Impurities in General........................228 Temperature and the Stability of the Zinc Cell..............229 Practical Expedients for Control of the Zinc Cell...........234 Acknowledgments...........................234 Appendix................................235 Discussion...................:.......... - 236 Introduction It has been the experience of the writer, during some five years' work with electrolytic zinc, that the zinc cell is perhaps more sensitive to impurities in the electrolyte than the analytical methods as yet developed for the chemical identification and determination of these impurities; but that, when proper purification methods have been applied to a given solution, the behavior of the cell is quite independent of the original sources from which the zinc sulfate has been derived. It has also appeared that the behavior of the zinc cell is the best and surest check on the correctness and thoroughness of the purification methods used, because it indicates the presence of both current impurities and cumulative impurities derived from the leaching of the ore; it also indicates whether these impurities are current or cumulative, at least in so far as they are of serious importance commercially.

Jan 1, 1919

By Bradley Stoughton, M. Miyake

The importance of magnesium alloys as engineering materials has increased rapidly in the past few years. The most important properties of magnesium alloys are their lightness and strength, which result in their extensive use in aircraft and automobile construction. Recent progress in the metallurgy of magneaium seems to offer hope of the production of the pure metal at a reasonable cost. The use of magnesium would doubtless increase greatly if it could be produced at a cost comparable with that of aluminum. A preliminary survey of the magnesium-base alloys shows that the most promising from a practical standpoint are magnesium-aluminum and magnesium-zinc as binary alloys, and magnesium-zinc-aluminum as ternary alloys. The research reported in this paper is a preliminary study of binary magnesium-aluminum and magnesium-zinc alloys, as an introduction to a series of further investigations. Magnesium-aluminum System The magnesium-aluminum system was first studied by Boudouard,1 who merely determined the liquidus. An accepted constitutional diagram was given by Grube,2 who found a compound A13Mg4 (melting point = 462.7" C.) and two eutectics at 35 per cent. magnesium (451.6° C.) and at 68 per cent. magnesium (440" C.) Between the first eutectic and the compound a solid solution exists. This diagram was checked or supplemented by Pécheux,3 Broniewski,4 Eger,5 Schirmeister,6 Voge17

Jan 1, 1926

By C. G. Cheriton

The Bathurst mining district is located near the town of Bathurst on the north shore of the province of New Brunswick in eastern Canada. This region is the northeasterly extension of the Appalachian mountain system. The area is heavily forested and covered with a fairly uniform layer of glacial gravels and boulder clay. The relief is low, increasing to a few hundred feet in the north west and several hundred feet in the extreme southwest. Thus, rock outcrops are scarce and occur mostly along streams and ridges. These factors made conventional prospecting difficult and resulted in the district becoming an excellent place for the application of regional geological studies, air photo techniques, airborne and gound geophysical methods and soil sampling. Late in 1952, The Brunswick Mining and Smelting Company discovered a very large base metal sulphide body presently known as their No. 6 orebody. Early in 1953, another and even larger sulphide body was discovered and is known as the No. 12 ore body. Mining exploration was very active thoughout 1953 and in 1954, The American Metal Company discovered the orebodies which have been developed into The Heath Steele 'Mines. The location of these deposits is shown on figure one. In the latter part of 1954, The Anaconda Company became interested in the district and decided to make a geological study of this new and promising base rrietal area. The following paper presents the story of the application of modern geological and geophysical techniques, leading to the discovery of a large sul-nhidp liodv. The Bathurst district is generally underlain by the Tetagouche group of Middle Ordovician rocks.

Jan 1, 1961

By G. Broughton

For the past few years a great amount of work has been done on the viscosity characteristics and gelation of clay suspensions, much of which has been reported in papers published by the Institute.7,12,18,19,24 Impor-tant reviews have been made elsewhere by Evans and Reid,10 Marshall20 and Clews, Macey and Rigby,8 the last two on the general properties of clay. It is unnecessary, therefore, to recapitulate past work beyond recalling that three explanations for the high viscosity and gelation of clay suspensions have been put forward. For lack of more exact nomencla-ture, these may be called the water hull,16 mechanical interference" and attraction-repulsion" theories. The first pictures the clay particles as surrounded by relatively rigid water envelopes, which increase effective volume; the second emphasizes the mechanical interference of platy particles or their agglomerates; while in the third the particles are assumed to be held relatively rigidly at a distance from each other determined by the balance between the attractive (van der Waal's) forces and the elec-trical repulsions of the charges. 13,14 This article presents fresh data on clay suspensions, particularly on the influence of previous flow history of the suspensions, specific contra-ions, temperature, solvation and particle size, in an attempt to contribute to the solution of the problem.

Jan 1, 1938

Abbey, Robert Graham, District Mgr., The W. W. Sly Mfg. Co., 50 Church St., New York, N. Y. '21 Abbott, A. N Ave. Morelos 84, Cuernavaca, Morelos, Mexico '23 Abbott, Argyle Campbell, Geol 42 Everett St., Arlington, Mass. '29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Consolidation Coal Co., Watson Bldg., Fairmont, W. Va. '15 Abeel, George H., Jr., Cons. Min. Engr 1281/2 S. Canon Dr., Beverly Hills, Cal. '18 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh. .Pittsburgh, Pa. '28 Abel, Walter D., Cons. Engr 650 S. Grand Ave., Los Angeles, Cal. '82 Abele, Louis T., Min. & Met. Engr., Supt., Texas Hill Mine Coulterville, Cal. '31 Abell, Leo M. Millicent, S. Australia '31 Abernathy, George Elmer, Prof. of Geol. & Min., Kansas State Teachers College, Pittsburg, Kan. '20 Aborn, Robert H., Research Lab., U. S. Steel Corp. Lincoln Highway, Kearny, N. J. '19 Abozeid, Mahmood, Dept. of Mines & Quarries Cairo, Egypt '26

Jan 1, 1932

By Carl E. Johnson

INTRODUCTION A method for predicting water-flood oil recovery was reported by H. Dykstra and R. L. Parsons' in 1950. It is now generally known as the Dykstra-Parsons method and is widely used by petroleum engineers. The method is semiempirical and consists of a correlation of four fundamental variables. These are: V, vertical permeability variation;' a, mobility ratio; Sw initial water saturation; and R, fractional recovery of oil in place at a given producing water-oil ratio. The correlation extends over a wide range in each of these variables, and may be applied to all formations with initial oil saturations of 45 per cent or greater. The method of calculation originally outlined by Dyhtra and Parsons closely follows their derivation. And this is a convenient way of illustrating the development of some rather complicated ideas. However, in actual use it is more cumbersome than necessary. The purpose of this note, therefore, is to provide a simplified method for making Dykstra-Parsons predictions. A SIMPLIFIED GRAPHICAL SOLUTION The correlation between V, a, Sw and R, corresponding to a given producing water-oil ratio, can be shown on a single graph. This is best done by plotting V against a to show lines of constant R(1 - S, . WOR-0.2). Figs. 1, 2, 3, and 4 show these plots

Jan 1, 1957

By D. L. Luffel

This paper presents two main developments: (1) a short, constantly accelerated centrifuge method of measuring drainage capillary pressure properties of cores, and (2) a new analytic method of treatment of centrifuge measurements to obtain saturation-capillary pressure relations. Toward the first objective, a clever experimental method is presented which is certainly more rapid than previous centrifuge methods. Toward the second objective, a new analytic method is derived to eliminate the approximate method of Hassler and runner. The derivation of this new analytic method, however, appears to be in error. The new analytic solution is developed as Eq. 5 in Appendix A. At the beginning of this derivation, the average wetting phase saturation of a core is expressed as, where is the centrifuge angular velocity. Eq. D1.2 makes explicit the dependence of S and S upon The second equation shown in Appendix A expresses the relation between the three variables Since for a given porous medium the saturation is uniquely related to capillary pressure, the functional dependence of S upon P is trivial, i.e., Pc.ri does not actually appear. Thus, the function 5 (r, ) may be expressed as a new function, S*, of PC, , alone The author transforms the variable of integration in Eq. Dl through use of Eq. D2 and writes

Jan 1, 1965

By H. A. Schwartz, A. F. Gorton, H. R. Payne

In a previous paper1 we published what we believed to be a correct stable equilibrium diagram for an iron-carbon alloy containing + 1.20 per cent. silicon. The purpose of the present paper is to record the results of studies concerning the effect of silicon on the location of the eutectoid points of both systems, including also certain incidental observations of general interest. We prepared white cast irons containing roughly 21/2 per cent. carbon, 0.05 per cent. manganese, and 0.03 per cent. each of phosphorus and sulfur, but of accurately known silicon contents which varied from 0.40 to 3.32 per cent. These were completely graphitized, and both A1 points determined, as in our previous work, the specimens being converted from the stable to the metastable condition and vice versa by appropriate heat treatments. Each stable alloy was heated to a few degrees above Arl for 3 to 7 hr., quenched and analyzed for total and graphitic carbon, the difference being the "combined" or, better, agraphitic2 carbon content of the saturated solid solution just above the eutectoid transformation. One specimen was lost through accident, and the 0.40-per cent. silicon material gave an anomalous result ascribed to difficulty in maintaining the stable system in the presence of but little silicon.

Jan 1, 1923

By H. R. Payne, A. F. Gorton, H. A. Schwartz

In a previous paper1 we published what we believed to be a correct stable equilibrium diagram for an iron-carbon alloy containing + 1.20 per cent. silicon. The purpose of the present paper is to record the results of studies concerning the effect of silicon on the location of the eutectoid points of both systems, including also certain incidental observations of general interest. We prepared white cast irons containing roughly 21/2 per cent. carbon, 0.05 per cent. manganese, and 0.03 per cent. each of phosphorus and sulfur, but of accurately known silicon contents which varied from 0.40 to 3.32 per cent. These were completely graphitized, and both A1 points determined, as in our previous work, the specimens being converted from the stable to the metastable condition and vice versa by appropriate heat treatments. Each stable alloy was heated to a few degrees above Arl for 3 to 7 hr., quenched and analyzed for total and graphitic carbon, the difference being the "combined" or, better, agraphitic2 carbon content of the saturated solid solution just above the eutectoid transformation. One specimen was lost through accident, and the 0.40-per cent. silicon material gave an anomalous result ascribed to difficulty in maintaining the stable system in the presence of but little silicon.

Jan 1, 1923

By G. Bjorling

The opening oxidation of a hydrometallurgical treatment of natural sulphides must for several reasons be so controlled that a maximum of the sulphide sulphur is transformed into elemental. If the oxidation is performed at low pressure and moderate temperatures and with mild reagents such as diluted nitric acid (or ferric or cupric chloride) the just mentioned condition is realized and it has been found possible to conduct the reaction so that solutions are obtained from which the metals can be recovered and the reagents required for the dissolution are regenerated. Experiments in laboratory scale with nitric-acid promoted oxidation have shown that this method is applicable to several types of raw materials, and in combination with electrodialysis both for partial neutralization and for final regeneration of the circulating acid can the requirements of low consumption of chemical reagents and formation of harmless residues be well fulfilled. The metals can be recovered as cathodic deposits or as hydroxides, and the method should be applicable also for low grade ores and concentrates. Although oxidation of sulphides by ferric or cupric ions has the advantage that it can be performed in open vessels it seems well worth the complication of working with nitric acid promotion in a low-pressure autoclave. Also complex sulphidic, oxidic and metallic materials can be treated.

Jan 1, 1973

By A. L. Titchener, M. B. Bever

The stored energy of cold work was investigated in drawn gold-silver wires by tin-solution calorimetry as a function of strain, strain rate, initial grain size, and temperature of defornation. The energy expended in the deformation process was measured. Hardness was also measured and was correlated with the stored energy as a function of strain and strain rate. Mechanisms of energy storage are discussed. THE variables which determine the amount of energy stored in a metal during cold work are of two kinds: those involving the metal and its condition and those involving the process of deformation. For example, the stored energy differs between one metal and another and between different degrees of purity of a single metal. It also depends on the nature of the deformation process and particularly the extent, rate, and temperature of deformation. Most investigators have reported the stored energy as a function of strain (or some similar geometric parameter) or of the energy expended during deformation. In general the stored energy increases with strain, rapidly at first, but more slowly at large strains until a saturation level is reached. Information about the effects of other variables, however, is limited. Some data are available on the dependence of the stored energy on the purity of a metal1 and on the composition of

Jan 1, 1960

Jan 1, 1969

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By K. E. Gray, M. S. Seth

In Part I of this work,1 equations of elasticity were formulated for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure. Equations of elasticity and the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant rate of pressure or a constant rate of flow is maintained at the wellbore. In this paper, the approach presented earlier is extended to finite reservoirs for the cases of (1) steady-state flow, (2) constant pressures at the well bore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Results of this work show that radial and tangential stress gradients are high near the wellbore but diminish rapidt; away from the well; the vertical stress gradient behaves in the same way but is less severe. Radial stresses are compressive or neutral, whereas tangential and vertical stresses may be tensile, neutral or com-pressive, depending upon the boundary conditions, the physical Properties of the system and the radial distance involved (vertical stresses are always compressive in an unbounded system1. For constant boundary pressures, both radial and tangential stresses increase with time whereas they both decrease for a closed outer boundary and constant pressure at the wellbore. The vertical stress decreases with time for both systems. For steady-state systems, radial displacement may be positive or negative, depending upon the dimensions of the system, the pressure differential and the porosity. Radial displacement may be positive or negative for a closed outer boundary but is positive for constant pressures at both boundaries. INTRODUCTION The importance, utility and complexity of a realistic appraisal of the stress state at and local to a wellbore were indicated in Part I. In this paper the analytical approach presented earlier is extended to finite, cylindrical reservoir geometry for the cases of (1) steady-state flow, (2) constant pressures at wellbore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Other than the outer boundary of the reservoir being finite, the physical system and assumptions pertinent thereto are the same as before. The reader may wish to review the mathematical development through Eq. 49 of Part I before proceeding here. SOLUTION FOR GENERAL BOUNDARY CONDITIONS THERMAL STRESSES AND DISPLACEMENTS Since normal stresses do not exist at the free boundaries of a system subjected to thermal stresses, the boundary conditions are

Jan 1, 1969

By W. H. Bassett

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (1) Depth of deoxidation of copper heated in reducing gas is greater the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this difference in depth of deoxidation is that, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much mire rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900° C.; that is, deoxidation is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide present in the copper. IN 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: FIG. 1.-EFFECT OF TIME AND TEMPERATURE ON DEOXIDATION RATE OF 0.365-IN. COPPER BY ILLUMINATING GAS; COPPER PLUS SILVER, 99.983 PER CENT. Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

By H. Gisser

Recent experimental work has demonstrated (1)2 that ammonia and oxides of nitrogen are formed during the aging of smokeless powder. This is significant in connection with the problem of "season cracking," or stress corrosion of brass cartridge cases in view of other work(1) indicating that stressed and "stress- relieved" cases stored with small quantities of added ammonium nitrate crack on firing. The deterioration of stressed brass by ammonia has been known for some time(z) and it appears therefore that stress- corrosion cracking of brass cartridge cases is intimately associated with the so-called "powder volatiles," ammonia and oxides of nitrogen, both of which are decomposition products of smokeless powder. Working on the hypothesis that any barrier which prevents the powder volatiles from reaching the brass surface will reduce the incidence of stress-corrosion cracking, it was considered desirable to investigate the use of organic resin films to accomplish this purpose. The possibility of formation of ammonia within the nitrocellulose powder charge and by reduction of nitrogen oxides on the surface of the brass case requires that the barrier film be resistant both to ammonia and oxides of nitrogen. The film must also be impermeable to ammonium salts, either solid or in solution, since these salts and water necessarily appear within the powder charge. The usefulness of the

Jan 1, 1945

By I. Cadoff, E. Miller, K. Komarek

Jan 1, 1960

By A. L. Field

Bureau of Mines Technical Paper 189 consists of a record of the scientific data obtained in the iron blast-furnace slag investigation which is reported in Technical Paper 187, "Slag Viscosity Tables for Blast-Furnace Work." It includes a description of the method of preparing the synthetic melts, construction of an improved electric furnace, and refinements in laboratory methods of measurement. Only the general features of the work and the conclusions drawn from the experimental data can be given attention here. Silicates in the Liquid State In the manufacture of refractories, Portland cement, glass, and porcelain, and in pyrometallurgical operations, importance attaches to the behavior of silicate compounds at temperatures beyond the range of common experience. This field of research has not been investigated as carefully as its scientific and industrial importance would seem to warrant. Probably the most important of the unsolved problems in the, chemistry of silicates is the question of their stability in the liquid state. That little progress toward the solution of this problem has been made is not strange if there be borne in mind the difficulties attending experiments made at temperatures at which silicates become fluid, and the comparatively short time since it became possible to measure these temperatures. On the other hand, considerable progress has been made in the study of the compounds in the solid state because of the directness and simplicity of methods of optical examination.

Jan 12, 1917

By William Fink

THIS paper is the nineteenth of a series from the Aluminum Research Laboratories, presenting the results of the investigations of equilibrium relations in aluminum-base alloys made from electrolytically refined aluminum. In previous papers equilibrium) relations have been deter-mined and correlated for 12 binary systems. Equilibrium relations have also been determined for portions of the aluminum corners of three ternary systems (aluminum-iron-silicon, aluminum-magnesium-silicon and alu-minum-copper-magnesium). The object of the present paper and those to follow is to increase our knowledge of the aluminum corner of the more important ternary systems. In 1926 Dix and Keith? suggested a new method for designating the phases encountered in alloy systems. The system has been used to a very limited extent 1,2,3. The system has since been slightly modified and will be used in this and future papers. In the system as modified, a phase is designated by placing in parentheses the chemical symbols of the elements essential to the formation of that phase. The symbols in the parentheses are separated by dashes in order to clearly distinguish them from a chemical formula. Elements that are not necessary to the formation of the phase in question, but which may be present in solid solution, are not indicated in the designation. If two or more phases would have the same designation according to these rules, they are dis-tinguished by prefixing Greek letters, and are definitely identified by X-ray diffraction patterns.

Jan 1, 1936