Search Documents

By H. N. Eavenson

The eleven mines of the United States Coal and Coke Co. in the Pocahontas coal field are situated in McDowell County, W. Va., which is a mountainous region. The valleys rarely exceed 200 ft. (60 m.) in width, the hillsides slope from 25°to 33°, and the tops, from 600 to 900 ft. above the valleys, carry practically no level land. At least 80 per cent. of the area is covered with timber. All the workings are drift mines; and while the average grades of the seams worked are ample for drainage, local dips and swamps necessitate the use of a large number of local pumps or of numerous drainage ditches to keep the mines free from water during heavy rains. The water handled in any mine is not great, compared with the coal output, and usually causes little trouble except during extremely wet periods. In new workings, the water encountered, except in rare cases, is trifling; it is only after rib drawing has started and the surface has been broken that water troubles begin. The strata overlying the coal are sandstone, shales, and slates; as the soil is thin and sandy, it does not tend to puddle and stop the cracks, which remain open for a long time. As mining progresses and the robbed area increases, the broken area becomes larger, increasing the openings into the mined territory. The cover over the robbed portions of the mines varies from 30 to 750 ft. (9 to 228 m.). When the ground is saturated, considerable water finds its way into the mines the day after a heavy rainfall and for three or four days it tends to fill the low places, wash the tracks, etc. and unless from three to four times as many pumps are installed as are normally needed, considerable output is lost. In most cases the water will flow from the mines, and the obvious solution is to provide drainage ditches of ample size to carry the maximum flow expected, so that the inflow will have no opportunity to flood the working places. Laying out the drainage headings on the proper average grades was an easy matter but where blasting was necessary to provide uniform grades, as was frequently the case, it was important that the maximum flow to be expected and the size of ditches to be provided should be known so that only rock work necessary to provide proper drainage

Jan 1, 1922

By Leland Russell van Wert

In 1888, Howard,1' working at the Watertown Arsenal on the tensile properties of ferrous materials at various temperatures, noted the curious fact that the stress-strain diagrams of low-carbon steels tested within a certain temperature range (200" to 350" C.) departed more or less from the normal regularity of such diagrams as secured by testing at either above or below these temperatures. This same jagged appearance of similar diagrams for steels has been observed by at least one other investigator, and de Forest2 has reported similar irregularities in the tensile testing of some nonferrous alloys. Recently again, this anomaly in diagram contour has been shown in a most striking fashion, apparently because of its accentuation by the method of testing employed, by Dr. Albert Sauveur.~ He described (for nonaustenitie steels) two quite distinct types of torsional stress-time diagrams: (1) those with a regular and smooth outline, derived normally by testing at temperatures above 300" C., or below 200" C. (as, for example, Figs. 4a or e); and (2) those presenting a decided "stepped" appearance, which are invariably produced when twisting is done within the 200" to 300" C. range (examples, Figs. 5a and b). The torsion test brings out so much more sharply (and convincingly) the irregularities occurring at 200' and 300" C. than does the tensile test that they can no longer be considered as resulting from simply idiosyncratic or accidental and inconsequential causes. Clearly, from the temperatures involved, the "stepped" type of diagram, or more accurately, the peculiar manner of response to torsional stress which manifests itself in the diagram, is an aspect of the "blue-heat" phenomenon. One's curiosity, if nothing else, prompts an inquiry as to the nature and significance of these "steps." What do they mean? What causes them To these questions there are no completely satisfactory answers. The following experimental observations are offered as suggestions towards the solution of the problem.

Jan 1, 1931

By C. J. P. Ball

Prior to 1939 the bulk of the magnesium metal produced outside of the united Stater was extracted directly from the ore and ifi the United States from magnesium chloride obtained as a by-product from the treatment of natural brines. A typical brine is one containing about 0.25 to 0.75 per cent bromine, 11 to 14 per cent sodium chloride, 9 to 11 per cent calcium chloride and 3 to 10 per cent magnesium chloride. The state of Nevada was known to possess large deposits of magnesite ore (MgCOs, the carbonate of magnesium), in Gabbs Valley, near Luning, approximately 350 miles north of Boulder Dam. Deposits mined in Europe were supplying magnesite giving 97 per cent MgCOs with about I per cent each of silica, lime and oxides of iron and aluminum. parts of the Luning de-posits Were almost equally rich, and the general average was of sufficiently high grade for production of magnesium. power to the amount of 200,000 kw. was available immediately from Boulder Dam, and water from Lake Mead, and it was this combination of available power, water, and ore that led to the initial proposal to erect a magnesium reduction plant in southern Nevada to reduce the magnesite ores from Gabbs. The extraction of magnesium metal from these magnesite deposits had been considered by the I. G. Farbenindustrie of Germany as far back as 1929. Mine and Oxide Plant The mine and oxide plant of Basic Magnesium Incorporated are perched upon the oride slope of the Paradise Range, at an altitude of 5000 ft., overlooking the 30 mile desert panorama of Gabbs Valley, Nevada. , Ore Occurrence The Gabbs magnesite ores occur in a thick series of flat, westerly dipping dolomites of Upper Triassic age. The mag-"esite bodies are exposed in steep canyon "areas encircling the north and east edges of a northerly projecting tongue of a roughly elliptical stock of granodiorite, which intrudes the dolomite. The magnesite mineralization is considered to be a a of calcium by magnesium through the agency of hydro-thermal solutions associated with the intrusion of the granodiorite. The ore bodies are of very irregular shape and distribution. Incomplete evidence points to deep pipelike replacement shapes that mushroom out erratically at various elevations. A wide latitude in the degree of magnesium replacement is reflected in a variance of quality from pure magnesite to magnesitic dolomite. The, ore is a massive crystalline mag-nesite. Though some differences in characteristics occur between ore bodies, in general the ore is a medium-grained carbonate varying in color from white, through all shades of gray, to black. Recrystallized dolomite, which encloses and occurs as

Jan 1, 1944

By Irving Fatt, Robert J. S. Brown

INTRODUCTION The wettability of reservoir rocks is recognized as one of the major factors that determines their multiphase flow properties. Multiphase flow properties in turn govern reservoir performance. For this reason, the reservoir engineer is vitally interested in the wettability of reservoir rock. The production research scientist is interested in wettability because the solution of the problem of improving waterflood recovery by use of surface-active additives may hinge on a detailed understanding of the wettability of reservoir rock. Early workers believed that all reservoir rocks were preferentially water wet. Continued study soon uncovered certain rocks which had flow properties that indicated that they were preferentially oil wet. Recent studies show that there is a spectrum of wettability. Some reservoir rocks have multiphase flow properties which indicate that they have an intermediate wettability. The differences in recovery observed among different reservoirs may, in part be the result of small differences in wettability. Differences in wettability amcng reservoir rocks may be the result of differences in the fraction of the total surface area that is preferentially oil wet and preferentially water wet. Nuclear magnetic relaxation measurements may provide a method for determining the fraction of preferentially oil wet and preferentially water wet area in porous media. Measurements to be reported here were made on water-saturated unconsolidated sand packs which were mixtures of preferentially oil wet and preferentially water wet sands. The resulting data show definitely that the fraction of each wettability in these sand packs can be determined by this nondestructive method of measurement. THEORY OF NUCLEAR MAGNETIC RELAXATION The details of the theory of nuclear magnetic relaxation have been presented previously1. In this paper, only a very brief review of the theory will be given to show its application to the measurement of fractional wettability. Nuclear magnetic relaxation is a process of adjustment undergone by certain atomic nuclei when their magnetic environment is changed. They adjust, or relax, to be in equilibrium with a new magnetic field. The reason that some atomic nuclei are affected by a magnetic field is that they themselves behave in some respects like tiny magnets. In particular the proton, the nucleus of the hydrogen atom, behaves as a magnet. The proton spins, somewhat as the earth spins on its axis. The spinning charge produces a magnetic field just as current traveling in a loop of wire produces a magnetic field. No net charge is required, however; for instance, the neutron has spin and magnetic moment. When the spinning proton is subjected to an externally applied magnetic field, its axis tends to line up with the magnetic field, somewhat as a compass needle tends to line up, but the spinning proton cannot do this as easily as the needle can. The proton also has mass, and its spinning mass makes the proton behave somewhat like a gyroscope. As is well known, a force which tends to change the axial direction of a gyroscope merely causes the gyroscope to precess: lhat is, the axis begins to trace out a conical surface. The gyroscope cannot actually assume the position suggested

Jan 1, 1957

By A. B. Kinzel

THE demands of the petroleum and chemical industries for steels to be used in pressure vessels and similar structures at artificially low tempera-tures are continually increasing, and the writing of proper specifications with suitable tests becomes increasingly important. Likewise, the selec-tion of suitable steels for such applications is of increasing concern to the metallurgist. It is generally recognized that highly alloyed steels of the austenitic stainless type retain their properties even at very low tempera-tures and represent the best technological solution of the low-temperature steel problem. However, in many instances less expensive carbon or low-alloy steels suitable for service within limited temperature ranges are available. The problem thus becomes one of defining the various factors involved in the production and fabrication of these less expensive steels and determining the temperature ranges in which their properties justify engineering application. Most of the applications involve welded structures, and the heat effect of welding as well as the nature of the weld metal are matters of prime concern. The first problem that the metallurgist faces is the determination of the type of test to be used as a criterion of the performance of the steel in low-temperature service. It has been generally recognized that the static properties of steel as determined in the ordinary tensile test undergo a gradual and relatively slight change as the temperature of test is lowered in the range of current interest; i.e., from room temperature to minus 120° C. It is further generally recognized that the behavior of steel under impact involving notch sensitivity is definitely affected at the lower temperatures. While the major subject of this paper is the effect of grain-refining deoxidizers, of low-alloy additions and of welding on the low-temperature notched-bar impact properties, an inquiry into the general behavior of steel under low-temperature impact testing is included. This is a pertinent portion of the investigation and the results thereof are

Jan 1, 1937

By J. H. McCormick

This plant, near Marysville, Mont., was planned to treat the ore from the Piegan and Gloster mines, the latter being one of the early and famous producers of the Marysville district. When the mill was closed in 1888, treatment consisted of stamp milling, followed by pans and settlers for pan amalgamation. The extraction was evidently poor, because, a few years later, thousands of tons of tailings were re-treated by the ranchers in the valley below the mill, by the then new cyanide process, and gave a handsome profit. In 1914, the present owners, after laboratory tests and an experimental mill run, decided upon the following treatment: crushing to 40 mesh in cyanide solution, concentration, amalgamation, classification, and cyani-dation of sands by leaching, and of slime by agitation and decantation in charges. The ore averaged about $7 per ton, gold and silver, the ratio of weight being 1 oz. gold to 7.56 oz. silver. The ratio of gold and silver in tailings was 1 oz. Au to 36.6 oz. Ag; the quartz was sharp and sandy, however finely ground, and rather difficult to slime. The mechanical equipment was a No. 5 Symons gyratory crusher; three 10-ft. Lane slow-speed Chilean mills; one Wilfley roughing and one finishing table; one submerged-type Akins classifier; five 26 by 10-ft. fir leaching tanks; one 24 by 7-ft. Dorr thickener; four 14 by 16-ft. Dorr agitators; four 6-compartment double-row zinc-boxes having compartments 18 in. wide, 18 in. deep, and 34 in. long; Johnson zinc lathe; acid and vacuum filter tanks for treating precipitate; roasting furnace; and Case tilting No. 275 crucible furnace for melting precipitate. The mill is driven by electric power supplied by the Montana Power Co. at the following rates, per kw.-hr.: 200 to 300 hp., 0.68 c.; 300 to 500 hp., 0.61 c.; 500 to 750 hp., 0.55 c.; plus $1 per month per installed motor horsepower. The plant as above described was operated from May, 1915, to the end of the year, when an additional Dorr thickener and a 12 by 12-ft. Portland revolving filter were added, increasing the nominal capacity of 100 tons per 24 hr., but not the percentage of extraction. The combined treatment, at a cost of $1.48 per ton, saved 90 per cent. of the gold arid

Jan 1, 1919

By A. C. England, William F. Haney, Paul B. Crawford, Bobby L. Landrum

The creation of unsymmetrical vertical or horizontal fractures in a producing well will result in a unique distortion of the normal shut-in pressures existing at the four surrounding wells. An electrical model study has been made to show how the shut-in pressures at the wells surrounding the fractured producing well may he used to estimate the size and orientation of vertical or horizontal fractures. The pressure differences at the four surrounding wells are recorded during production from the fractured well. The resulting pressure dato are matched from a table of several hundred possible fracture combinations. The table refers to the figure showing the effective size and orientation of the commercially created fracture. INTRODUCTION The creation of commercial fractures about oil and gas wells has led to considerable speculation as to the size and shape of the fractures. It is important that the size and shape be known in certain instances, especially when pressure maintenance programs are to be initiated. It was shown that if knowledge of a vertical fracture could be found that such information may be utilized in planning a waterflooding or gas cycling program and that in some cases the fractures might be utilized very effectively.' Other work showed that it may be desirable to create "pancake" fractures in certain reservoirs but that they should exist in a desirable range.' If the fractures are too large, they should be plugged prior to initiating a pressure maintenance program. If an irregular shaped "pancake" fracture is created, it is desirable to know the orientation of this fracture because similar but unreported studies have shown that "pancake" fractures may or may not substantially affect the sweep efficiencies and performance of the flooding or cycling program. Consequently, it may be desirable in some instances to estimate the effective size and orientation of the fracture. ANALOG An electrical model was used in making this study. The electrical model consisted of a circular reservoir approximately 8 in. in diameter, 1 in. thick and was filled with a dilute salt solution. A copper band formed the periphery of the reservoir. A vertical fracture was simulated by a copper strip soldered to the wire well located in the center of the reservoir. Vertical copper strips of various lengths and orientation were soldered to the wire well to represent vertical fractures in the reservoir. In studies reported here on vertical fractures it was arbitrarily assumed that two fractures originated at the well and extended out into the reservoir. An electrical potential was imposed between the wire well and the periphery of the tank. Plots of the iso-potentials are shown in Figs. 1 through 9. This model provides the steady-state isopotentials existing in a uniform, homogeneous circular reservoir having a vertically fractured well at its center. The permeability of the fracture is much greater than the permeability of the matrix proper. The effects of gravity are neglected. In preparing Tables 1 and 2, four symmetrically located unfractured wells were assumed to exist around

Jan 1, 1956

By Walter P. Jenney

In the limestone area of Tintic and other mining districts of the Great Basin region of Utah, it has been observed that surface-outcrops of ore occur but seldom, and are mainly confilled to points of relatively low elevation, where the veins cross some basin or ravine. Nowhere does a considerable body of ore outcrop on the tops or high up on the slopes of the hills. Mining operations, on the other hand, have shown that large and continuous ore-deposits frequently occur in depth in the limestone, beneath large masses of barren rock. Such orebodies, when followed upward in the lodes, are found to terminate at well-defined levels, without reaching the surface. Yet the minerals-bearing fissures themselves extend above the top of the ore, being often traceable, though barren of all valuable minerals, for hundreds of feet above the stopes in the mines, and even observable in outcrops at the surface. This abrupt cessation of the ore at a uniform horizon does not appear to be connected with any change in the countryrock adjacent to the lodes. The strata above and below this horizon seem to be in every way equally favorable to ore-deposition. Explorations above it have developed an open-fissured country, barren not only of ore, but also of indications that minerals bearing gold, silver, lead or copper were ever deposited in the strata at that elevation. The height reached by the ore, while usually constant throughout the length of a given lode, may vary in particular sections, from the operation of local causes. Each lode in a district has its own distinct horizon, above which the oredeposits do not extend. Where the ore-bodies are continuous

Jan 1, 1903

By American Institute of Mining Engineers

David J. Mack (University of Wisconsin, Madison, Wise.)—Have the authors considered that the effects reported in their paper are readily explainable on the basis of equilibrium grain boundary segregation rather than ordering? It seems to the writer that all of their experiments and observations correlate well with known behavior associated with equilibrium grain boundary segregation. Although at first glance one would tend to dismiss such a possibility because of the similarity of the gold and copper atoms, their sizes differ by 12.8 pct which is in the range where segregation at grain boundaries would be expected. Then, too, the electrochemical differences between the copper, the Cu3Au, and the gold strongly suggest that a segregation mechanism is involved in the corrosion of the Cu-Au alloys. R. Bakish and W. D. Robertson (authors' reply)—The authors would like to thank Dr. Mack for his consideration of the problem of grain boundary segregation as an explanation of the observed phenomena. We had considered the problem in the following terms: Assuming a pure binary Cu-Au alloy and an ideal solid solution, the surface excess, T2= N25 — N2, of the second component (gold) may be expressed in the following way20 1 —exp (—da/kT) where 8 is the difference in surface tension of copper and gold, and a is the surface area per atom. In the present case, 6 is positive which implies that the component in excess at the boundary is gold. Since the only chemically active component in ferric chloride is copper, it does not appear that the segregation of gold is likely to increase the boundary activity. A small concentration of a third component could profoundly affect the situation. Analysis indicated only spectrographic traces of impurities, all of which are soluble in both copper and gold. Quenching experiments, reported in the paper, also tended to eliminate significant effects attributable to a third component.

Jan 1, 1958

By R. V. Wheeler, W. Francis

Of the methods that have been used for studying the chemical composition of coal, attack by reagents has not, in general, yielded much information. Most of the reagents used have been strong oxidants such as nitric acid or Schulze's solution. The use of a milder oxidizing agent, such as air at low temperatures, enables progressive changes in the character af the coal substance to be studied and thus helps toward an understanding of its constitution. British bituminous coals frequently have a banded structure. These bands (of four types) can be separated one from another and have been found to possess markedly different chemical characteristics, even when taken from contiguous portions of the same lump coal. It has been found convenient to give each of the ingredients of banded coal a distinctive name, more or less descriptive of its appearance, and the study of the chemistry of bituminous "coal" in England has resolved itself into a study of each ingredient separately. The coal chosen for this work was taken from the Top Hard seam at East Kirkby colliery, Nottinghamshire, a detailed chemical analysis of which has been recorded by Baranov and Francis.' The banded structure was well marked and the bands could readily be separated. The research was confined to the brilliant vitreous bands (vitrain), the dull hard bands (durain) and the "sooty partings" main); for previous work had shown that the fourth type, to which the name clarain has been given, is intermediate in character, chemically, between vitrain and durain. The method of experiment was, briefly, to draw a slow current of moist air through weighed samples (50 gm.) of the three ingredients, vitrain, durain, and fusain, in the form of powder (through a 60-mesh and on a 90-mesh sieve) contained in glass tubes which could be maintained at a constant temperature during prolonged periods. After passing through the coal, the air bubbled into a measured volume of

Jan 1, 1925

By F. E. Smith, David R. Mitchell, B. M. Bird

DENSE-MEDIA processes utilize the familiar laboratory float-and- sink procedure on a commercial scale. Just as wood chips float on water and sand sinks, ,so coal floats and refuse sinks when placed in a medium intermediate in specific gravity between the coal and refuse. Liquids intermediate in specific gravity between coal and refuse used in commercial plants are of four types: (1) Organic liquids of high specific gravity-halogenated hydrocarbons; (2) dissolved, salts in water; (3) pseudo liquids obtained by suspending solids, such as sand, in water, and (4) fluidizing a mass of sand or other solids by air currents. Those most widely used for cleaning coal are solutions of calcium chloride in water and a suspended-sand pseudo liquid. Laboratory float-and-sink testing is an intermittent operation during which every opportunity is given for particles lighter than the medium to float and particles heavier to sink. Commercial processes are continuous, vertical and horizontal currents of the separating medium occur as either part of the process or unavoidably produced by the introduction of feed and withdrawal of products, so that the exact separation of the laboratory technique is not duplicated by commercial processes. However, separations close to the theoretical are obtained in commercial machines by careful technical control of the process. Most machines in commercial installations are crowded to get as much out of the equipment as possible, so that careful technical control is necessary to get the recoveries and grade of product desired. Sizes usually cleaned are plus 3/16-in. or plus 1/8-in. in the United States and plus 1/16-in. in Great Britain: Coal as small as 1 mm. has been cleaned in some experimental installations. The separation of coal from refuse in sizes finer than about in. is made difficult by viscosity' effects and hence at the present time cleaning is confined to the coarser sizes. Technical advances in the art of cleaning coal by dense-media

Jan 1, 1943

By F. C. Oliphant, George H. Fancher

Two samples of drilling mud from the Hastings oil field, Texas, were tested, and the solids in each were separated into small fractions of a limited range in particle size. The mineral composition of each fraction by X-ray analysis is reported, and the results are interpreted in relation to other measured quantities, such as the physical properties of the original samples and the density of the various fractions. It was found that only 7 to 8 per cent by weight of the solids was of colloidal dimensions and that neither of the samples contained montmorillonite but did contain illite. Considerable calcite was also found. These data should be useful to the geologist interested in the origin and history of sedimentary strata as well as to the petroleum engineer. Introduction The questions, What is good drilling mud? What constitutes bad drilling mud? are pertinent, because the proper use and control of drilling fluids has been a factor of great importance in the successful drilling and completion of oil wells since the days of Captain Lucas. Adequate control of the characteristics of drilling fluids has assumed greater significance comparatively recently because of the problems introduced by caving formations in deep wells, costly blowouts and impressive mud bills. Much is known about the solution of some of the problems but, despite extensive research directed toward a better understanding of the physical and chemical properties of clay suspensions, it is difficult to define precisely a drilling mud, and much more difficult to say what constitutes a good mud. It is generally believed that the smaller particles of a drilling mud greatly affect its physical properties. In fact, it is customary to blame the colloids in a mud for nearly everything that goes amiss, because colloidal properties have effects out of all usual proportion on viscosity, filtration rate and reaction to electrolytes. It is germane to know whether drilling muds possess colloids and if so, the quantity and kind. Source oF Samples Two drilling muds from the Hastings oil field, Brazoria County, Texas, were selected because it is generally agreed that in this oil field good natural muds made solely from formations penetrated by the drill can be used until the well is nearly ready for completion. Customary drilling procedure in this field is to spud in with water, set a protective string of pipe, drill to 2500 ft. and set the surface casing. Drilling is continued to 5500 ft. with no treatment of the drilling fluid other than addition of water to

Jan 1, 1943

By W. N. Lacey, R. H. Olds, B. H. Sage

The volumetric behavior of five mixtures of black oil and natural gas and of two mixtures of condensate and natural gas from a field in the San Joaquin Valley was experimentally established. This work was carried out at roo°, I9o° and 250°F in the pressure interval between 400 and 5000 psi. The viscosity of the liquid phase of four mixtures of black oil and natural gas was experimentally measured in the above-indicated temperature and pressure intervals. The effect of methane upon the precipitation of bitumen from the black oil was studied at 230°F. Introduction The solution of a number of the economical and technological problems which arise in connection with petroleum production is dependent upon the availability of the necessary quantitative information covering the materials involved. This requires data concerning physical properties of naturally occurring hydrocarbon mixtures at the pressures and temperatures characteristic of underground petroleum reservoirs. The experimental determination of the desired data for each situation encountered is relatively time-consuming. However, it is considered to yield results sufficiently more reliable than those obtained from correlations to justify the effort. For these reasons there was undertaken a laboratory investigation of the viscosity of the liquid phase and the volu- metric and phase behavior of mixtures of oil and gas samples obtained from wells in a field located in the San Joaquin Valley. Terminology The nomenclature of petroleum engineering is not at present entirely standardized. Many commonly used technical terms are not everywhere given the same meanings. For the purposes of this paper the following definitions will be adopted: Black oil refers to the dark-colored, hydrocarbon liquid obtained when the producing horizon of the well lies partly in the condensed hydrocarbon phase of the reservoir. Condensate is the term applied to the relatively volatile, pale yellow or amber-colored hydrocarbon liquid that is often obtained from the surface separator system when the producing horizon of the well lies in the gas cap of the reservoir. The gas obtained from the surface separator system is called natural gas regardless of whether the well is producing black oil or condensate. As might be expected from the multi-component character of naturally occurring hydrocarbon materials, the compositions of black oil, condensate and natural gas are subject to considerable variation depending upon the temperatures and pressures prevailing in the surface separator system as well as upon the overall composition of the material produced from the reservoir. In order to obtain samples capable of reproducing the total hydrocarbon material produced by the well, all oil and gas mixtures used in this investigation were com-

Jan 1, 1949

By W. D. Robertson

THE effect of a tensile stress in accelerating the corrosion-cracking of certain alloys of aluminum, magnesium and iron is widely recognized. The literature is extensive and it is only necessary to cite the recent ASTM-AIME Symposium.1 There are, however, no experimental data conclusively showing the effect of an applied compressive stress. It has been inferred, from the generally accepted mechanism postulated for the acceleration of corrosion by an applied tensile stress, that a compressive stress would inhibit corrosion. Furthermore, it is observed that corrosion cracks invariably start on the tension side of a specimen bent as a simple beam. This observation has led to the suggestion that shot-peening of the surface would inhibit or eliminate stress-corrosion cracking in magnesium alloys, and aluminum alloys.3 However, the degree of inhibition produced by shot-peening does not appear in the literature except for the above qualitative references which are unsupported by experimental data. Moreover, while peening undoubtedly imposes a surface compressive stress, the alteration of the surface by the severe cold-working involved complicates the interpretation of the results with respect to the effect of a compressive stress alone. If corrosion proceeds along preferential paths produced by precipitation from solid solution, it is easily understood how a component of tensile stress normal to these paths will accelerate the corrosion and lead to ultimate failure. On the other hand, if the metallurgical conditions are such as to create preferential corrosion paths, then it is difficult to understand how a compressive stress, produced by shot-peening or any other method, can inhibit corrosion except in the sense that the accelerating factor is removed. Thus, if the basic corrosion mechanism remains unaltered, there should be little or no inhibition resulting from the application of a compressive stress if in¬hibition is defined as the reduction of the degree of corrosion below that experienced in the unstressed state. The experiment described below was performed to isolate and evaluate the effect of a compressive stress on the corrosion and stress-corrosion cracking of a high strength aluminum alloy (24-S); and, by a comparison of the corrosion rate of specimens subjected to an applied tensile stress, compressive stress and in the unstressed state, to clarify the role of stress in intergranular corrosion. EXPERIMENTAL PROCEDURE The experiment was conducted with the aluminum-copper-magnesium alloy known as Duralumin 24-S.* Specimens, 0.064 in. thick, in the form of I in. wide strips sheared parallel to the rolling direction,

Jan 1, 1947

By F. C. Oliphant, George H. Fancher

Two samples of drilling mud from the Hastings oil field, Texas, were tested, and the solids in each were separated into small fractions of a limited range in particle size. The mineral composition of each fraction by X-ray analysis is reported, and the results are interpreted in relation to other measured quantities, such as the physical properties of the original samples and the density of the various fractions. It was found that only 7 to 8 per cent by weight of the solids was of colloidal dimensions and that neither of the samples contained montmorillonite but did contain illite. Considerable calcite was also found. These data should be useful to the geologist interested in the origin and history of sedimentary strata as well as to the petroleum engineer. Introduction The questions, What is good drilling mud? What constitutes bad drilling mud? are pertinent, because the proper use and control of drilling fluids has been a factor of great importance in the successful drilling and completion of oil wells since the days of Captain Lucas. Adequate control of the characteristics of drilling fluids has assumed greater significance comparatively recently because of the problems introduced by caving formations in deep wells, costly blowouts and impressive mud bills. Much is known about the solution of some of the problems but, despite extensive research directed toward a better understanding of the physical and chemical properties of clay suspensions, it is difficult to define precisely a drilling mud, and much more difficult to say what constitutes a good mud. It is generally believed that the smaller particles of a drilling mud greatly affect its physical properties. In fact, it is customary to blame the colloids in a mud for nearly everything that goes amiss, because colloidal properties have effects out of all usual proportion on viscosity, filtration rate and reaction to electrolytes. It is germane to know whether drilling muds possess colloids and if so, the quantity and kind. Source oF Samples Two drilling muds from the Hastings oil field, Brazoria County, Texas, were selected because it is generally agreed that in this oil field good natural muds made solely from formations penetrated by the drill can be used until the well is nearly ready for completion. Customary drilling procedure in this field is to spud in with water, set a protective string of pipe, drill to 2500 ft. and set the surface casing. Drilling is continued to 5500 ft. with no treatment of the drilling fluid other than addition of water to

Jan 1, 1943

By Robert F. Mehl

THE purpose of a symposium, I take it, is to gather together a group interested in a common intellectual field, in order to exchange views, and to appraise the state of knowledge. Symposia are the more successful, the greater the activity in the chosen field and the wider the range of applicability of the information gained. From time to time, as emphasis changes from one field of research to another, a given subject may enjoy popularity and later retire into a scientific somnolence, for fashions change even among engineers and scientists. The subject of this symposium, however, enjoys the advantages of wide applicability and of high current interest and productivity in results. It is a timely subject for a symposium; with much new information, surely metallurgical engineers should now devote an increasing attention to its application to practice. In beginning the symposium, I shall attempt briefly to appraise our basic knowledge in the field, to survey instances of practical usefulness, and to suggest where new work might be most productive of useful results. There are many examples of direct practical application of diffusion knowledge, and it is the purpose of the several papers in this symposium to review these. In this introduction I shall attempt to take a broad view, which, while it will but poorly serve the engineer in the solution of any given problem, may perhaps be of some use in assessing the state of knowledge in this field. RATE OF DIFFUSION Liquid Metals The process of diffusion among liquid metals, of gases in liquid or solid metals, or among solid metals, is ubiquitous, to say the least. The manufacture of alloys by the intermelting of metals, the addition of ferroalloys to molten steel, the deoxidation of molten alloys, all involve diffusion in the liquid state. The oxidation of molten copper for purposes of purification, the unsought oxidation of alloys generally during melting and casting, the reaction of liquid steel with oxidizing slags in the open-hearth furnace, the absorption of nitrogen by liquid steel, particularly in the bessemer furnace, all operate by the diffusion of gases in liquid metals. These processes have not been studied much from the viewpoint of rates of diffusion. Alloys are made by melting metals with stirring and with allowance of time for mixing (which is diffusion) but I know of no studies that seem to define the necessary times, and though in only very rare cases can faulty properties of the finished castings be ascribed to inadequate mixing, and though certainly in most cases, with stirring, the rate of diffusion is adequate to give sufficient mixing, a more quantitative treatment would be good to have. It is not wholly certain that thorough and sufficient mixing is at all times attained, for I suspect that ferroalloy additions to steel, and that additions of aluminum to steel as a deoxidizer, especially in the sampling of steels

Jan 1, 1944

By O. P. Arora, M. Metzger, G. R. Ramagopal

Single-phase aluminum containing 0.0001 to 0.06 pct Cu was studied in strong acid, mainly through observations of hydrogen evolution. The strong influence of copper was exerted almost entirely through the imposition after a certain delay time of an auto-catalytic localized-corrosiott reaction. Additions of cupric ion to the acid produced lower accelerations. The significance of the quantity and distribution of copper was discussed, and the implications for intergranular corrosion and neutral chloride pitting were indicated. AN investigation of intergranular corrosion in single-phase high purity aluminum exposed to hydrochloric acid indicated the copper content of the metal to have an influence on corrosion at lower levels than previously suspected.&apos; The work reported here was a closer examination of the action of copper but dealt with general corrosion to gain the advantage of having a continuous measure of corrosion through the volume of hydrogen evolved, the reduction of hydrogen ion to hydrogen gas being the principal or only cathode reaction in strong hydrochloric acid. Previous work on the hydrochloric acid corrosion of aluminum was sometimes insufficiently structure-conscious and the need for care in evaluating it arises from the low solubility of the iron impurity,&apos; and of some alloying elements, and the known or possible presence in many of the compositions studied of second phases leading to greatly increased corrosion rates.3 These increases are attributed to the presence of low hydrogen-overvoltage cathodes provided by the second phase.3&apos;4 For the present single-phase work, a few studies which used high-purity base material and small copper additions5-&apos; provide the essential information most unambiguously. The corrosion rate was shown to be increased markedly by the introduction into the acid of small quantities of the ions of copper (and of certain other metals) which cement on the aluminum and provide cathodes of low overvoltage.5 When there was sufficient copper in the aluminum, the same result was produced during the course of corrosion leading to a rate which increased with time as the reaction was stimulated by one of its products (autocatalytic reaction). In 2N (7pct) HC1, an accelerating rate was observed at 0.1 pct Cu but not at 0.01 pct.5,7 The present work dealt with corrosion rate and morphology and their correlation with the quantity and distribution of copper catalyst for copper contents from 0.0001 to 0.06 pct. PROCEDURE A lot of high-purity aluminum containing 0.0021 pct Cu, 0.001 pct Fe and 0.003 pct Si (Alloy A) was alloyed with copper to yield aluminum containing 0.014 pct Cu (B) and 0.06 pct Cu (C). Later it was found necessary to include the lower copper Alloy K which contained 0.0001 pct Cu, 0.0004 pct Fe and 0.0004 pct Si. The upper limit for any other element can be confidently estimated as 0.0005 pct. No element other than copper appears to be present in quantities sufficient to have an effect on general corrosion as great as the observed effect of the copper in A, B, and C. The only other heavy metal detected by spectrographic examination was silver (< 0.0001 pct). The acid was made up from a selected lot of 37 1/2 pct CP hydrochloric acid containing 0.1 ppm heavy metals (mainly Pb), 0.05 ppm Fe, and < 0.008 ppm As and from water distilled from 1 megohm-cm demineralized water and believed to have contained negligible quantities of heavy metals influencing corrosion. Acid strength was adjusted to within 0.05 pct HCl of the stated value by using precision specific gravity measurements. Test blanks 10 by 41 mm were sheared from 1.65-mm cold-rolled sheet. Edges were finished by filing. The blanks were annealed in air at 645°C for 24 hr in alundum boats and rapidly water quenched. The anneal is thought to have produced a substantially homogeneous solid solution—for iron, copper, or silicon, for example, the annealing temperature was 200°C or more above the solvus-and the quench is considered to have preserved the high-temperature structure except for the condensation of lattice vacancies into dislocation loops.&apos; The 0.06 pct Cu alloy did not appear unstable in respect to slow precipitation reactions at room temperature since two pairs of tests failed to show significant differences between specimens heat treated 3 1/2 years earlier and specimens heat treated 1 or 2 days before.

Jan 1, 1962

By R. T. DeHoff

A new approach to the measurement of the size distribution of particulate structures imbedded in opaque bodies is developed. The method is based upon the assumption of a general two-parameter distribution curve, and the estimation of these two parameters from three well-known counting measurements made upon metallogvaphic sections. The total number of particles in the system is also a product of the analysis. Application of the method with the assumption of the logarithmiconorma1 disfribution function is developed in detail. A complete description of the geometry of a particulate structure requires the determination of the size distribution of particles. The problem of estimating the size distribution of particles of a particular phase in a multiphase system, or the grain-size distribution in a homogeneous system, has been approached by many investigators.&apos;-&apos;0 All of the solutions proposed by these investigators share the following characteristics. a) A minimum of several hundred particle sections in the microstructure must be examined, and some characteristic dimension recorded, such as area,3&apos;5 intercept length,6"9 or diameter.1&apos;2&apos;4&apos;10 b) The resulting data must undergo a series of fairly complex calculations to generate the empirical histogram which describes the size distribution in three dimensions. c) In order to manipulate the result, the histogram must be fitted to some assumed mathematical formula, using the attendant statistical procedures. d) With two notable exceptions,8,10 the particles must be spherical. The measurements and calculations involved are in general very tedious and time-consuming, with the logical result that much effort has been expended in the development of equipment which will perform these tasks automatically and semiautomati-cally.9,11-15 considerable success has been achieved in this area, but the equipment is in general expensive, and usually places stringent requirements On the quality of microstructure which can be reliably analyzed. In laboratories which do not possess such equip- ment, the analysis of geometry is usually limited to measuring total properties of the microstructures, such as volume fraction and interfacial area, because the measurements required are much simpler to make. The determination of size distributions rarely is undertaken. The development which is presented in this paper permits the estimation of size distributions of three-dimensional structures from the same simple counting measurements which are required to determine the surface area and volume fraction of the particulate structure, and one other counting measurement. The basic approach that is used is to assume a general mathematical form for the distribution, which is described by two parameters (as the normal distribution is described by assigning values to the mean and the standard deviation), and then estimate these two parameters from the results of the counting measurements. The introduction of a third counting measurement also permits the evaluation of the number of particles per unit volume, Nv.

Jan 1, 1965

By E. T. Turkdogan, P. Grieveson

It is shown experimentally that, by making use of the coupled S-O reaction in ionic melts, it is possible to transfer slclJur or oxygen from a lozv to a high chemical potential through an ionic nzenzbrane. This uphill transfer of sulfur is accompanied by a counter downhill transfer of oxygen and vice versa. The Materials balance shows that the amoulits of sul -fur and oxygen lost or gained by one system are the same as those gained or lost by the other systenz — the two systejns being separated by an iofzic membmne. The systems used in these experi?nents were solid Mn-MnS-Mno and liquid Fe-S-0. Sufficient results were obtained Lo study the kinetics of the transfer and the indications are that the counter diffusion of sulfide and oxide iojzs in the membrane is the rate controlling process. WHEN an ionic oxide-melt reacts with an atmosphere containing sulfur and oxygen-bear ing gases the following reaction occurs: 1/2 S2 (gas) +O2- (melt) = S2- (melt) + 1/2 0, (gas) [1] Under the restrictions that i) electric conductance in the melt is purely ionic and ii) each constituent element in the melt does not change valence, the solution of an atom of sulfur in the melt will result in the evolution of an atom of oxygen, so that the electric neutrality is maintained. For a given temperature and melt composition, the equilibrium concentration of sulfur in the melt is determined by the ratio, po2 /ps2 , in the gas phase and not by the individual partial pressures of oxygen and sulfur. This has been demonstrated by a number of investigators, for example by Richardson and withers&apos;, Fincham and Richardson,la by St Pierre and Chipman,&apos; and by Turkdogan and Darken.3 In his Howe Memorial Lecture for 1961, Darken discussed the possibility of uphill pumping of sulfur through an ionic membrane at the expense of oxygen. TO test the validity of this concept associated with coupled reactions, experiments were carried out in the following manner. A presintered mixture of Mn-MnS-MnO and prefused mixture of Fe-S-0, contained in platinum and iridium crucibles, respectively, and separated by a thin layer of soda-glass (to act as an ionic membrane), were placed side by side in an evacuated silica capsule and sealed. This was then kept at 1400°K for a required time to allow Reaction [11 to occur via the ionic membrane. When partial equilibrium is reached, the ratios Po2 /pS2, for systems on either side of the membrane, are equal and the flux of sulfur and oxygen through the membrane becomes zero, although the individual partial pressures po2 andp,, in these two systems may differ considerably.

Jan 1, 1962

By N. D. Gerald

The mathematical analysis, which is an essential part of this paper, has revealed the interesting fact that contrary to the opinions of many, determinate and measurable economic factors are largely responsible for the price of crude oil. It should, however, be well understood that the results of this analysis are applicable, without qualification, only to the particular period and market studied. There are certain peculiarities of the petroleum industry which make the consideration of its economics very difficult, and at times practically impossible. Noneconomic factors often become highly important and have serious economic effects, which make unqualified predictions based on economic data extremely hazardous and ill advised. However, in spite of the attendant difficulties there are many problems, especially in price analysis, to which approximate solutions must be made for the proper guidance of public and private policy, but their limitations should be kept clearly in mind. An understanding of the nature of prices is of fundamental importance for a number of purposes. Measurement of the motivating factors giving rise to trends and other price movements is essential to forecasting for the intelligent engineering and financial administration of the industry. The fixing of prices, maintenance of an intelligent industrial dictatorship, or the making of other industrial adjustments, demand, for success, an accurate understanding of their probable consequences. The establishment of a system of equitable relations within an industry, or between industries, by methods other than the natural competitive ones, requires a thorough knowledge of the price structures and the nature and trends of the normal and basic prices of their products. This research has shown that in this case, even though the statistical records are only fair, quantitative economics offers a direct and satisfactory approach to the problems of economic consequences dependent on the reactions of mass intelligence. A consideration of commodity prices naturally leads to costs. The true cost of petroleum is so complex and elusive that its accurate deter-

Jan 1, 1934