Search Documents

By B. K. Larkin, H. R. Bailey

One of the most complicated and potentially one of the most promising secondary recovery methods is that of underground combustion. A number of field tests1,2,3 have been performed recently, apparently indicating that the underground combustion process is technically feasible. Relatively little has been published concerning laboratory or theoretical investigations of the underground combustion process. A few results of laboratory tube runs have been published4,5 and these data are valuable in understanding the process. The tube run data also emphasize the complexity of the thermal recovery process. Under various conditions, problems in heat transfer, multiphase fluid flow and combustion rates arise. For example, at low temperatures the combustion process proceeds so slowly that the front cannot be propagated. It is a problem in heat transfer to predict what injection rate of air is necessary to sustain combustion in a particular reservoir. Certain fluid flow aspects of underground combustion have been studied by Wilson, et a13. In the development of some of the flow equations, assumptions of adiabatic combustion were made. Vogel and Krueger1 have devised an analog model of the heat conduction process for a constant temperature cylindrical source moving radially outward in a homogeneous conducting medium. Jenkins and Ramey7, in a discussion of the Vogel and Krueger paper, present an analytical solution of a heat conduction problem related to problems considered by Vogel and Krueger. In the present paper an idealized model of the heat conduction problem is considered, which is more general than the model of Vogel and Krueger or Jenkins and Ramey. In particular, initial well heating, vertical heat losses and arbitrary frontal velocities are included. Equations for the temperature are obtained in terms of integrals. These integrals have been evaluated numerically for the case of frontal movement corresponding to a constant air injection rate and the case of constant frontal velocity. These results are presented graphically. From these graphs one may estimate conditions under which nearly adiabatic temperatures are obtained. The application of these results requires some knowledge of reservoir thermal properties, combustion rates and residual fuel content. Assuming no vertical losses it is possible to obtain explicit evaluations of these integrals in the linear con- stant velocity case and in the radial case corresponding to a constant air injection rate. PRESENTATION OF RESULTS The geometry of the radial system is illustrated in Fig. 1 where the reservoir is represented as a slab of thickness h. By making an energy balance for an infinitesimal volume, one obtains the following equation. T= x T+F(z.r).........(1) where F (z,r) =HWv1/pc (r-r1), if z h/2 = 0, if z >h/2 . In Eq. 1, V- represents the Laplacian operator and 8 is the Dirac delta function. Eq. 1 is the well-known diff-sion equation with a source term and may be applied to a linear system. For example, if the source is moving in the direction of the x axis, then the argument of the delta function is x - 1,. In deriving Eq. 1 the following approximations were made concerning the actual combustion process: (1) all heat transfer is by conduction in a homogeneous medium, (2) the formations bounding the reservoir have the same thermal properties as the reservoir, (3) the combustion fuel is consumed instantaneously as the front arrives, (4) there is a constant fuel concentration

By D. S. Tannhauser, I. Bransky

Measurements of the electrical conductivity, the thermal electromotive force, and the deviation from stoichiometry by thermogravimetry were made on ferrous oxide (wüstite) single crystals as well as on poly-crystalline samples in the temperature range of -900" to 1330°C. In the region defined by T 2 1000°C and 1.05 5 O/Fe 5 1.10 the electrical conductivity was shown to be proportional to the sixth root of- the oxygen partial pressure and to be linearly dependent on the deviation from stoichiometry. The absolute Seebeck coefficient of single and polycrystalline wüstite was shown to be independent of temperature in the above region and a p to n transition of the Seebeck coefficient was observed at O/Fe = 1.09 in polycrystalline wüstite. Analysis of the results showed that the predominant defects in wüstite in the above region were doubly ionized cation vacancies. The analysis also ruled out the existence of complexes of the type postulated by Roth, except that below 1000°C there is some evidence of 'association of defects. Of the three oxides of iron (FeO, Fe3O4, Fe2O3) only FeO (wüstite) can exist within a wide range of the ratio O/Fe. This has been shown by several investigations of the phase diagram using for instance chemical analysis of quenched samples'-4 or thermogravimetric measurements. 5,8 Darken and Gurry's1 data for example in the temper- ature range 1100o to 1400°C show that the lowest O/Fe ratio obtainable for FeOl +. is about 1.045 and that the existence range extends to O/Fe = 1.20 at 1400oC. On the basis of detailed analysis of thermogravimetric measurements made by Vallet and Raccah6 the existence of three varieties of wüstite at elevated temperatures was suggested by these authors and by Kleman. It is well-established that wüstite has a NaCl structure with vacant cation sites.3, 8 From a neutron-diffraction study of wüstite samples quenched to room temperature Roth9 concluded that defects in wüstite are mostly complexes composed of two cation vacancies and one interstitial cation in a tetrahedral site. The atomic arrangement in the vicinity of such a defect is similar to that in magnetite, where each occupied tetrahedral site is surrounded by four vacant octahedral positions disposed at the corners of a tetrahedron, so arranged that each vacancy is shared by two tetrahedral cations. Thus there is an average of two vacancies per interstitial. Recent X-ray diffraction measurements made by Smuts10 on quenched wüstite samples confirmed the results of Roth's neutron-diffraction experiments. Roth's model of defects in FeO can be regarded as a solid solution of Fe3O4 in FeO; salmon1' used this defect model to calculate the activity of Fe3O1 in FeO at high temperature and claimed good agreement with the results obtained experimentally by Darken and Gurry.' Each missing cation in wüstite is accompanied by two trivalent cations, thus preserving charge neutrality. The "holes" which differentiate between the Fe 2+ and Fe3' states of the ions in octahedral positions can overcome the attractive field of the cation vacancies, and are then free to move through the crystal as charge carriers. A similar picture holds for COO, NiO, andMnO.l2, 13 Localization of the charge carriers in transition

Jan 1, 1968

By Lawrence H. Van Vlack, Otto K. Riegger, Gerald I. Madden

The microstructural variations of periclase (MgO) in the presence of oxide liquids are examined under the steelmaking variables of: 1) temperature, 2) liquid composition, and 3) FeO additions under different oxidation levels. Attention is given to the distribution of the phases, both liquid and solid, and to the growth of individual crystalline grains. Silicate liquids penetrate more extensively between individual periclase grains than do liquids containing high percentages of Fe2O3 Higher MgO solubilities in the liquid and lower MgO contents of the solid favor more rapid grain growth. The presence of a second solid phase reduces the periclase grain growth rate and increases the amount of the solid-to-solid contact within the oxide microstructures at high temperatures. The service suitability of a refractory depends on many factors. Two are of major importance and include 1) the thermal resistance to melting, and 2) the mechanical resistance to loads at service temperatures. Neither is a simple consequence of the service temperatures because service conditions will alter compositions, produce partial melting, and induee phase changes. Consequently, the equilibrium phase relationships have been rather thoroughly studied and give a knowledge of the thermal resistance to melting, but do not give full information about the mechanical properties because two refractories with the same types and quantities of phase may have different microstructures. Although variations of microstructures with time, temperature, and composition have been subjects for extensive investigation in metals, only a limited amount of comparable microstructural work has been performed for refractory materials.' This study was an attempt to evaluate some of the consequences of service parameters upon the microstructures of refractories so that bases may be established for the analyzing of high temperature mechanical properties. Periclase (MgO) was chosen as the refractory oxide; variables included those which are encountered under steelmaking conditions such as 1) temperature, 2) liquid composition, and 3) FeO additions under various oxidation levels. Specific attention was given to the distribution of the phases, both liquid and solid, and to the growth of individual crystalline grains. The most closely related work on microstructures of polyphase materials is that of Van Vlack and Rieg-ger2 on the microstructure of magnesiowüstite [(Mg,Fe)O] in the presence of silica. In that work which pertained to solid solutions with less than 40 pct MgO, most of the quantitative work was performed on FeO microstructures. The chief conclusions concerning these relatively low-melting oxide solids were as follows: 1) the rate of crystalline grain growth is inversely proportional to the grain diameter, 2) grain growth proceeds more rapidly at higher temperatures but is slightly retarded by additional liquid content, and 3) a Silicate-containing liquid penetrates as a film between the individual magnesiowüstite grains independent of time, temperature, amount of liquid, or the MgO/ FeO ratio. The above observations are in contrast to prior work3 on the microstructure of silica in the presence of iron oxide-containing liquids where the liquid does not penetrate as a complete film between solid grains. The phase relationships for the compositions of the present work are shown in Fig. 1 which is a summary of the work of several investigators.4 Of importance is the fact that CaO forms a more stable structure with SiO2 and Al2O3 than do either MgO or FeO. The oxygen potential has little effect on periclase unless iron oxide is also present. The iron oxide is ferrous at moderately low oxygen levels, changing to ferric as the Oxygen potential is increased so the spinels, magnetite, and magesioferrite are formed.5 These two phases are relatively stable in air at steelmaking temperatures. I) EXPERIMENTAL PROCEDURE ractory were made with reagent grade Oxides. The magnesium oxide used was 99 pct MgO after ignition, and the iron oxide raw material had a minimum content of 99 pet Fe2O3. The CaO, SiO2, and A12O3 were also reagent grade raw materials. After mixing, the required compositions were pressed into pellets at a minimum pressure of 5000 psi to insure compaction of the raw materials and prevent excess void content. A silicon carbide element tube furnace was used with thermocouple control for sin-

Jan 1, 1963

By H. E. Searle, Robert J. McKay, O. B. J. Fraser

The practical study of corrosion requires consideration of its economic aspects. It must be based on sound scientific principles, but it should be borne in mind that probably the most important object of a corrosion test is to determine what metal in corrosion-resisting construction will produce the greatest operating profit. Thus the corrosion test must be directly connected with money values or it is not a practical corrosion test. This, perhaps unusual, connection between corrosion and economics is partially due to the fact that corrosion deals only with the time factor or duration of equipment, and it is almost the only test which deals with this feature. In these statements a departure is made from the academic definition of the word corrosion and it is done deliberately. The use of the term corrosion is unusual. It is as though we spoke of a tensile test as a "breaking" test. We are not interested primarily in the break but in the strength of the metal. There is no English word which expresses our main interest in corrosion-testing, but let us have clearly in mind that we make corrosion tests to prevent corrosion. Our real interest is in this corrosion-prevention, not in the corrosion. Previous to 1922, it was common comment that "it is impossible to determine the course of corrosion by laboratory testing.'' This statement was true at that time in that the technique of laboratory testing for corrosion resistance was so vague that tests in the laboratory gave untrue results almost as often as true ones. This was so, even in the simple case of determining which one of two metals better resists a given solution. While this is no longer true the number of misleading "corrosion tests" still being ground out by laboratories is too large in the light of our present knowledge. There are two important features of corrosion testing whose neglect is a large contributing factor to misleading results: (1) The economic relations of the corrosion tests to other tests; (2) testing technique. Regarding economic relations J. F. Thompson l has said: "The use of any particular metal is rarely based upon the sole property of resistance to corrosion. In fact, I should like to venture the assertion

Jan 1, 1929

By Robert J. McKay, O. B. J. Fraser, H. E. Searle

The practical study of corrosion requires consideration of its economic aspects. It must be based on sound scientific principles, but it should be borne in mind that probably the most important object of a corrosion test is to determine what metal in corrosion-resisting construction will produce the greatest operating profit. Thus the corrosion test must be directly connected with money values or it is not a practical corrosion test. This, perhaps unusual, connection between corrosion and economics is partially due to the fact that corrosion deals only with the time factor or duration of equipment, and it is almost the only test which deals with this feature. In these statements a departure is made from the academic definition of the word corrosion and it is done deliberately. The use of the term corrosion is unusual. It is as though we spoke of a tensile test as a "breaking" test. We are not interested primarily in the break but in the strength of the metal. There is no English word which expresses our main interest in corrosion-testing, but let us have clearly in mind that we make corrosion tests to prevent corrosion. Our real interest is in this corrosion-prevention, not in the corrosion. Previous to 1922, it was common comment that "it is impossible to determine the course of corrosion by laboratory testing.'' This statement was true at that time in that the technique of laboratory testing for corrosion resistance was so vague that tests in the laboratory gave untrue results almost as often as true ones. This was so, even in the simple case of determining which one of two metals better resists a given solution. While this is no longer true the number of misleading "corrosion tests" still being ground out by laboratories is too large in the light of our present knowledge. There are two important features of corrosion testing whose neglect is a large contributing factor to misleading results: (1) The economic relations of the corrosion tests to other tests; (2) testing technique. Regarding economic relations J. F. Thompson l has said: "The use of any particular metal is rarely based upon the sole property of resistance to corrosion. In fact, I should like to venture the assertion

Jan 1, 1929

By M. S. Burton, J. E. Ritter

The sessile-drop technique was employed to study the effect of atmosphere and alloy additions of titanium and chromium on the surface tension and contact angle of nickel on sapphire substrates at 1500oC. Shear tests were conducted on the solidified sessile drops. The liquid-gas surface tension of pure nickel on sapphire was found to be 1747 ergs per sq cm, with a contact angle of 109.6 deg. The surface tension and contact angle were not affected significantly by the four atmospheres, vacuum, impure argon, pure argon, and pure hydrogen. Small additions of titanium and chromium decreased the contact angle and for the same alloy content, contact angles were lower in pure argon than in pure hydrogen. On the basis of shear-test results , the most probable cause for adhesion in the Ni-Al2O system is the formation of NiO:Al2O3 spinel at the interface; in the titanium alloy-Al2O3 system adhesion is thought to be due to a mechanical interlocking effect; in the chromium alloy-Al2O3 system adhesion is believed to be the result of solid-solution formation involving Cr2O3 and Al2O3 at the interface. In the last few years there has been considerable interest in reinforcing metals with ceramic whiskers. It has been postulated that, by reinforcing nickel with sapphire whiskers, high-temperature strengths su- perior to those of the best current nickel alloys can be achieved.' To fabricate a whisker-metal composite having optimum density and strength, understanding of wettability and adherence in the system is of prime importance. Although there has been some previous research in this a a need for further studies has been cited4-8 to understand better the effects of impurities, alloys additions, and atmosphere on the wetting and bonding of metals to metal oxides. The purpose of this research was to investigate the factors involved in the wetting and adherence of nickel/nickel alloys to sapphire (single-crystal a Al2O3). Sessile-drop experiments were conducted in vacuum, impure argon, pure argon, and pure hydrogen, to determine the effect of atmosphere on the contact angle of the metals on sapphire, and the liquid-gas surface tension of pure nickel. The solidified sessile drops were sheared from the sapphire substrate to measure the bond strength between the metal and ceramic. The alloy additions chosen were titanium and chromium since both enhance the wetting of nickel on sapphire.2, 3c Also, titanium is commonly used when brazing metal-to-ceramic seals to improve adherence. Since chromium forms an oxide that is completely soluble in sapphire, it was thought that the oxide could serve as a transition phase to promote bonding between the Ni-Cr alloy and sapphire. I) EXPERIMENTAL APPARATUS AND PROCEDURE The sessile-drop apparatus was a horizontal furnace, with an induction-heated, cylindrical molybdenum susceptor in a water-cooled Pyrex chamber. This apparatus was patterned after that of Williams and Nielsen.7 A flat Pyrex window at each end of the furnace allowed temperature measurements to be made at one

Jan 1, 1968

By K. E. Barrett

Exxon owns a uranium mill and holds two mining leases in Live Oak County, Texas, about halfway between San Antonio and Corpus Christi. The properties make up the Felder Uranium Operations which was reopened earlier this year. Exxon held an oil, gas, and other minerals lease on the J. C. Felder tract, which was adjacent to a relatively shallow uranium discovery by Susquehanna-Western, Inc. on the Marrs-McLean lease immediately south of the Felder property. Drilling in 1967 and 1968 confirmed the presence of reduced uranium mineralization in the basal sand unit of the Oakville formation on the Felder tract, which formed the major part of the roll-front deposit. In 1969 Exxon and Susquehanna-Western, Inc. entered into a sale and purchase agreement which provided for Susquehanna to mine and process Felder ore and purchase recovered uranium. Susquehanna moved an alkaline-leach mill from Wyoming, erected it on the Ray Point property, and placed it into operation late in 1970. Susquehanna mined and processed ore from the Felder and McLean properties through March 1973. Susquehanna ceased operations in March 1973. Exxon then acquired the mill and mill property. Exxon also purchased the mineral rights to the McLean lease, re-negotiated a mining lease for that property, and carried out shut-down programs for the mining and mill areas in the fall of 1973. The project was put on a standby basis until late 1973, when Exxon initiated mine feasibility studies for the project. MINE PLANNING EVALUATION The feasibility study for reopening the Felder Project began in late 1975 and was not completed until late 1976. I will discuss several areas of the feasibility study that required additional work prior to making the decision to renew operations. Ore Reserves Preparations for estimating the ore reserves began with the re-evaluation of more than 1500 natural radioactivity logs from exploration and pre-development drilling that had been completed on the property. These gamma ray logs of non-core rotary drill holes were the principal source of data used in making the estimate. Chemical assays of cores from the deposit were also used in the reserve determination. Electric resistivity and self-potential logs were made along with the gamma ray log. In December 1975 an additional core drilling project was undertaken to confirm the in-place density and radiometric equilibrium characteristics of the ore deposits. Comparison of chemical assays of cores with the U308 values calculated from the logs showed that the unoxidized ores were in radiometric equilibrium. In contrast, cores from anomalies occurring in near surface, weathered, and oxidized zones were in radiometric disequilibrium. Several important decisions were made in developing a mine plan or schedule of production from the Felder and McLean ore bodies. Disposal of Produced Mine Water: The ore bodies of the Felder Uranium Project occur at a point below the ground water table. The ore zones to be mined must first be dewatered to allow removal of mineralized material. In the open pit operations, this is accomplished by maintaining a perimeter ditch around the periphery of the open pit, allowing the interior of the pit to drain and collect into a sump and be pumped from the mine. In addition to anticipated water production from future mining operations, approximately 200M gallons of water was contained in three open pits left from prior mining operations. In two of these existing pits, the water was to be removed and disposed to allow for planned backfilling of waste material into these pits. The third pit would also have to be drained to allow continued mining of an area left from the prior operations. Essentially no ground water information was available for this area. The only data available was water production history from Susquehanna's mining operation. Two water wells were drilled early in 1976 on the Felder lease for use in obtaining hydrological data. A long term draw-down test was performed by pumping one water well and measuring water level drawdown in both the pumped well and the observation well. From these data, values for permeability and storage coefficient were calculated. These data were then used in modeling the aquifer to allow calculation of water influx into the mining area versus time. Once a schedule of water production, including the stored volume in the existing pits was calculated, alternate solutions for disposal were evaluated. The first system evaluated was a series of deep injection wells. The wells were designed to inject at a depth of approximately 3500 feet. Again very little information concerning reservoir characteristics of the receiving sand units was known. Using assumed values for reservoir permeability and storage coefficients, an injection well system was designed to allow for disposal of produced mine water. The biggest

Jan 1, 1979

By Wm. B. Price

The work of Leon Guillet concerning the effect of nickel on the structural properties of brass is checked. The best value for the coefficient of equivalence t, that is, the amount of zinc replaced by 1 per cent. of nickel, is shown to be-1.1 per cent. The best hot- and cold-working nickel silvers, varying in nickel content between the limits of 4 and 18 per cent., are tabulated and plotted diagrammatically. Also, some data are given showing a comparison between the physical properties of a hot- and cold-working low copper-nickel silver, and a commercial cold-working nickel silver containing approximately 8 per cent. more copper. THIS investigation of low copper-nickel silvers was undertaken to check the work of Leon Guillet on special brasses and to determine, more accurately, the effect of the addition of nickel on the microstructure of the binary alloys of copper and zinc. It was hoped that the results could be successfully applied to the practical production of low copper-nickel silvers. To explain the results of his investigations on special brasses, Leon Guillet evolved his conception of "fictitious compositions." He states,1 in his general conclusions, that on the introduction of a small amount of a third metal to a copper-zinc alloy, it enters into solid solution with the normal constituents up to saturation, but by so doing it brings the ternary alloy into a state microscopically equivalent to a binary copper-zinc alloy of fictitious composition, and physically more nearly like the latter than the brass containing copper-zinc in the ratio actually present. The physical properties of the ternary alloy, when compared to the same properties of an actual brass of the fictitious composition, are modified by the natural properties of the third element. Beyond the point of saturation, a special constituent appears and the above generalization no longer holds.

Jan 2, 1924

By E. Teghtsoonian, E. M. Schulson

The tensile behavior of bcc ordered P' AuZn single crystals (CsCl structure) has been investigated under varying conditions of temperature, composition, and orientation. Between -0.2 and 0.4 T, multi-stage hardening occurs fm stoichiometric and nonstoichio-metric crystals oriented near the middle of the primary stereographic triangle. At higher and lower temperatures, parabolic type hardening occurs, followed by work - softening at the higher temperatwes. Deviations from stoichiometry give rise to increased flow stresses. Multi-stage hardening was observed for most orientations, except along the [loll-[lll] boundary and near the [001] corner of the stereo -graphic triangle, where parabolic type hardening occurs. Along two slip systems, (hk0)[001] and (, operate simultaneously while in the [001] comer, slip occurs mainly on the system. Electron microscopy of deformed crystals revealed bundles of edge dislocations forming walls approximately Perpendicular to the glide plane. In general the plasticity of 4' AuZn closely resembles the plasticity of bcc crystals. In recent years, considerable interest has arisen concerning the mechanical properties of the CsCl type intermetallic compounds Ag Mg,'- Fe co,' and Ni Al.'-' The compound P'AuZn is structurally similar. It has a low and congruent melting point of 725"~,'" remains ordered up to the melting point,16 and pos-esses a range of solid solubility from 47.5 to 52.0 at. pct Au at room temperature.15 The present paper reports the results of an investigation on the general tensile behavior of material in single crystal form. Some dislocation configurations characteristic of the deformed state are also reported. The results of a detailed study of the slip geometry in AuZn are presented in a separate paper.17 PROCEDURE Alloy preparation, crystal growing techniques, and the procedure followed in selecting specimens of minimum composition variation are reported elsewhere.17 Dumb-bell shaped tensile specimens were prepared by carefully machining single crystals in a jewellers' lathe to a gage length of 0.80 in. and diam of 0.090 in. Back-reflection Laue X-ray patterns and room temperature tensile tests revealed that machining damage could be eliminated by electrochemically polishing 0.005 in. from the machined surface followed by annealing at 300°C for 1 hr. Specimens were polished in fresh 5 pct KCN solution (40°C, 12 v). Experiments were performed by gripping specimens in a self-aligning pin-chuck and threaded collet system, then straining in a floor model Instron tensile machine. All tests were performed in duplicate. Experimental variables included temperature, composition, and orientation. Unless otherwise stated the strain rate was 2.5 x 10"3 per sec. Liquid testing environments included nitrogen (WOK), nitrogen cooled petroleum ether (133" to 293"K), and silicone oil (293" to 488°K). Resolved shear stress-shear strain curves were electronically computed from autographically recorded load-elongation curves. Stress and strain were resolved on the macroscopic noncrystallographic (hkO) [001] system operative under the specific test conditions of temperature, strain rate, and orientation reported earlier.17 RESULTS The temperature dependence of the work-hardening curves is shown in Fig. 1 for gold-rich crystals of 51.0 at. pct Au oriented near the center of the stereo-graphic triangle. Over the range of intermediate temperatures from -200" to 400°K, they are very similar to those classically observed for fcc metals (reviewed by Nabarro et al.).'' The beginning of deformation is characterized by a region of decreasing hardening rate, stage 0, which is followed by a region of low linear hardening, stage I, and then a region of higher linear hardening, stage 11. At the higher temperatures, stage 111 is observed, a region of decreasing hardening rate. Over the intermediate temperature range, the extent of stage 0 and of the slow transition between stages I and I1 decreases with increasing temperature. Total ductility is large, often greater than 300 pct shear. As the temperature is either increased or decreased, the extent of stage I is decreased, giving rise to parabolic type flow and reduced ductility. Similar temperature effects have been reported for bcc ~r~stals.~~-~~ Below -14O°K, hardening is terminated in brittle fracture while above -400°K. initial hardening is followed first by work-softening and then by chisel-edge type ductile fracture. Stoichiometric (50.0 at. pct Au) and Zn-rich (51.0 at. pct Zn) crystals were also tested from 77" to -500°K. The effect of composition on the flow behavior is illus-

Jan 1, 1970

By F. V. Lene, E. J. Westerman

The recrystallization behaviors of two extruded and cold-drawn experimental sintered aluminum powder alloys, containing 1.75 and 3.0 pct Al2O3 by weight, were compared with that of extruded and cold-drawn commercially pure alumirzum. The kinetics of recrystallization of the alloys are described semiquantitatively. For the alloy containing 1.75 pct A l203 the rates of nucleation and of growth were also semiquantitatively determined. THE most striking property of aluminum alloys strengthened by a dispersion of Al2O3, the so-called SAP alloys, is their stability at elevated temperatures. One of the manifestations of this stability is their resistance to recrystallization after they have been cold worked. Most of the commercial grades of either the Swiss SAP or of Alcoa's Aluminum Powder Metallurgy Products have not been recrys-tallized after cold working, even when they are heated for a long time at a temperature near the aluminum melting point. Lenel, however, observed that the dispersion strengthened aluminum alloys with a larger spacing between the oxide particles than that of most commercial grades would recrys-tallize.1 It appeared to be of interest to further investigate the mode and kinetics of recrystallization of these alloys, and to compare their recrystallization behavior with that of commercially pure aluminum. Because homogeneous deformation of these SAP alloys in tension did not provide sufficient cold work to induce recrystallization, they were cold worked by wire drawing; the nonuniformity of this deformation unavoidably complicated the interpretation of the recrystallization studies. EXPERIMENTAL DETAILS Extrusions—Two types of sintered aluminum powder extrusions were used in this study. One type, designated AT-400, was produced from Reynolds atomized aluminum powder consisting of spherical particles averaging 3µ in diam and containing 1.75 wt pct of Al2O3. This powder was very similar to the R3M powder from which extrusions were previously prepared with an average spacing of 0.9µ between oxide particles.2 The second type, designated MD 2100, was produced from Metals Disintegrating Co. flake powder containing 3.0 wt pct of Al2O3, with an average flake thickness of 0.8µ. The average spacing between oxide platelets in MD 2100 extru- sions was 0.45µ.2 Powder compacts of 3/4-in. diam were extruded at 1000°F into 0.097-in. diam (AT-400) and 0.093-in. diam (MD 2100) wires by methods previously described.3 In order to compare the recrystallization behavior of sintered aluminum powder extrusions with that of wrought commercially pure aluminum 3/4 in. rod stock of 1100 F aluminum was extruded at 1000°F into 0.102-in. diam wire. Wire Drawing—Tungsten carbide dies were used for the AT-400 and 1100 F alloys. They had an included angle of about 15 deg and reduced the wire area approximately 7 pct per pass. Steel dies with an included angle of 11 to 13 deg and an average reduction per pass of 10 pct were used for drawing the MD 2100 alloy, because drawing this alloy through the carbide dies produced overdrawing defects. Heat Treatment—The cold-drawn wires were cut into small samples, and the deformed ends were etched off. The samples were each wrapped tightly in a single layer of aluminum foil, and individually isothermally annealed in a lead bath. Metallography—The modes and kinetics of recrystallization were determined by metallography. Mounted and polished specimens were anodized in a solution of 1.8 pct HBF4;4 examination under polarized light clearly revealed their grain structures. The recrystallized grains were generally much larger than those of the unrecrystallized matrix, and could clearly be distinguished because they alternated between maximum and minimum light reflection when the microscope stage was rotated, while the unrecrystallized matrix had a comparatively homogeneous "salt and pepper" structure. The fractional recrystallized volumes of the dispersion hardened alloy wires were determined by cutting and weighing of recrystallized and total transverse areas on photomicrographs. The recrystallized grains in the 1100 F alloy were too small to be cut out individually; therefore a combination of cutting and lineal analysis was used in this case. RESULTS AND DISCUSSION Modes of Recrystallization—The modes of recrystallization of the three alloys varied widely. In the 1100 F alloy nucleation and growth started in the region midway between the center and the surface;

Jan 1, 1961

By John F. Elliott, John P. Hager

The standard free energies of formation of the lowest stable sulfides of chromium, molybdenum, and tungsten in equilibrium with the corresponding metal hazle been determined by reacting the sulfide and metal with H2(g)/H2S(g) mixtures. The reaction is A method for estimating the standard ~nolav entropies and standard entropies of formation at 298°K of the sul-fides of refractory metals is presented. The standard free energies of formation of the lowest sulfides of the metals in group VIa of the periodic table are probably best determined with the reaction* is known with greater accuracy than is that property for any other sulfur-bearing compound or solution which might serve as a reference phase to establish the chemical potential of sulfur for the essential re- However, there still remain significant problems to the use of Reaction [I] in studying these sulfides. First, the equilibrium gas ratios (Ph2S/PH2) are very small, and with the most stable sulfides in the series the ratios tend to be at the limit of the range for precise chemical analysis (10-4); and second, the reaction rate for the formation or reduction of these sulfides appears to be relatively slow. A primary reason for the latter problem is that the gas phase near the equilibrium concentration has very little capacity for transport of sulfur. It is to be noted that the thermo-dynamic properties obtained from the experimental results by Eq. [I] apply for 1 g-atom of sulfur in the metal-saturated compound even though the exact composition of the compound has not been determined. The work reported here is a study of the standard free energies of formation of the lowest sulfides of chromium, molybdenum, and tungsten, and of copper, by Reaction [I]. In planning the experimental program, it was decided that the technique that has been used previously3"' could be used with modification and that an improved analytical method was needed for determining H2S in the gas phase. THE EXPERIMENT The once-through flow of gas was selected in preference to recirculating the gas, a) because of the low sulfur capacity of the gas, b) because of the relatively slow rate of reaction and the danger of the

Jan 1, 1968

By D. D. Dunlop, J. R. Welker

The growing interest in the use of CO, in crude oil recovery increases the need for data on the effect of CO, on hydrocarbon physical properties. Data are presented on the solubility of CO, in various dead oils, the swelling changes in CO2-oil solutions and the effect of CO, on dead oil viscosity. This latter property shows the most pronounced effect, with viscosity reductions up to 98 per cent of the uncarbonated viscosities. An empirical method of estimating the viscosity of carbonated oils is presented. The apparatus and procedures used are described in sufficient detail to allow others to make similar studies. INTRODUCTION The effect of dissolved carbon dioxide on the swelling and viscosity reduction of specific hydrocarbon oils has been observed and recorded by a number of investigators.'- me object of this paper is to offer a means of predicting these effects for crude oils free from natural gas, using the dead state viscosity and gravity of the crude oils. The CO, solubility and swelling of numerous crude oils were determined in a visual cell at various pressure levels. The viscosity of the oils carbonated to various pressure levels was then determined by measuring the pressure drop across a capillary tube. From these data, the physical properties were correlated empirically. The resulting correlations allow the prediction of CO, solubility, swelling and viscosity reduction if the dead state gravity and viscosity of the oils are known. SOLUBILITY AND SWELLING MEASUREMENT EQUIPMENT AND PROCEDURE A high pressure visual cell was installed in a constant temperature cabinet. A test gauge was attached at the top of the cell for pressure measurement, and a line was run through the cabinet wall to a wet test meter which was used for volumetric measurement of the gas. The first step in making a test run was to put the oil in the cell up to a level about half to two-thirds of the total volume. This required about 50 to 65 ml of oil. carbon dioxide was then bubbled up through the oil for a time during which the pressure of CO2 in the cell was kept above 800 psia. Saturation of the oil with CO2 at this pressure and ambient temperature was confirmed by slowly bleeding CO2 through a valve to the atmosphere. If the oil was completely saturated with CO2, bubbles of gas would form in the oil at the first small decrease in pressure. If the oil was under-saturated, no bubbles formed until the pressure was decreased to the saturation pressure existing in the oil. If this saturation pressure was lower than that desired, more CO2 was bubbled through the oil until the desired level was reached. After saturation at ambient temperature was completed, the cabinet temperature was adjusted to the desired level and the cell was allowed to reach temperature equilibrium. After temperature equilibrium was reached, the pressure was again decreased slightly, and the oil again checked for full CO2 saturation at the cell pressure. The pressure now had changed because of the difference in solubility of the CO, in the oil at higher temperatures and the expansion of CO2 as the temperature increased. The outlet tube from the cell was then connected to the wet test meter and the CO2 was allowed to flow slowly out of the cell and through the wet test meter at ambient temperature and pressure. The water in the wet test meter had previously been saturated with CO2 at ambient temperature and pressure by allowing CO2 to flow continuously through it lor a period of several hours. The gas flow was stopped at several pressures during the run and the cell was allowed to come to equilibrium; this made possible the measurement of solubility and swelling data at the intermediate pressures. The volume of the oil in the cell was recorded at each of the equilibrium pressures in order to obtain swelling data. DATA AND RESULTS The solubility of CO2 in the oil was calculated by the relationship V — V, where R. = solubility of CO, in crude oil, cubic feet of CO, measured at 60F and 1.0 atm/ bbl of dead state oil at the temperature under which solubility was measured, V, = volume of gas released from the cell between the saturation pressure and zero pressure, corrected to 60F and 1.0 atm, cu ft, V, = volume of CO: contained in the gas space above the oil, corrected to 60F and 1.0 atm, cu ft, and V, = volume of the dead oil in the cell in bbl at the temperature of the run. The volumetric data of Sage and Lacey' were used to calculate V., from the volume of CO2 at high pressures. The swelling factor was calculated as where V, is the volume of the C0,-

By S. A. Lever, R. Hultgren

The solidus is usually the least satisfactorily determined portion of a phase diagram. Cooling curves, which succeed well with the liquidus, show the solidus inaccurately or not at all because of segregation which occurs during freezing. Heating curves of carefully homogenized alloys might be expected to indicate accurately the solidus, but they are seldom used. Dynamic methods involving heating or cooling are never completely satisfactory because of uncertainty as to whether equilibrium is attained. A static method in which the specimen may be allowed hours, days, or even weeks to attain equilibrium is to be preferred. In a static method a solid solution, for example, is first made thoroughly homogeneous, then heated to successively higher temperatures. After sufficient time at each temperature to assure equilibrium, some property is measured which should alter strikingly when melting begins. Microscopic examination can be used to detect the beginning of melting, but the method is tedious since the specimen must be quenched, sectioned, polished, and etched before each examination. Of all the physical properties which change on melting, electrical resistance is probably the most satisfactory to measure. The measurement may be made while the specimen is at temperature without damage to the specimen. It may be repeated indefinitely to ascertain when equilibrium has been achieved. Measurements may be made on a single specimen over the whole range of temperature. Most metals approximately double their resistance on melting. Since an accuracy of a few tenths of a percent is easy to achieve, the method is highly sensitive to the beginning of melting. In spite of these advantages, which have been perceived for a long time,l,2 a reasonable search of the literature has failed to reveal a single case in which the method has been satisfactorily applied in practice to the determination of solidus temperatures. The use of electrical resistance measurements appears to have been confined in practice to changes in the solid state. In the work described in the following pages we have applied the electrical resistance method to the solidus of the lead-tin system. We have found the method to be convenient, reproducible, and highly sensitive. We chose the lead-tin system because it leads to few technical difficulties. Furthermore, a number of determinations of solidus have been made in this system by various methods and results could be checked against them. However, all published results are not in good agreement with one another, so this work should help in determining the solidus more precisely. The Lead-tin Diagram Because of its commercial importance, there have been numerous investigations of the lead-tin diagram. The results of the most recent work on the solidus are indicated in Fig 7, as well as the results of the present work. The works of Honda and Abe3 and of Stockdale4 agree fairly well with each other and with the present work. Jeffery's5 data indicate the solidus to be about 50°C lower. Honda and Abe3 used differential thermal analysis on both heating and cooling cycles. Stockdale4 used the microscopic method and also differential heating curves. Stockdale's results were about 4" higher than those of Honda and Abe at low tin contents and lower at higher tin contents. These results also agree with those of Rosen-hain and Tucker.= Jeffery5 used electrical resistance measurements of the alloy as it was being heated or cooled. Apparently he did not attain equilibrium as his results are about 40°C lower than those of Stockdale4 or Honda and Abe.3 MATERIALS AND METHODS The lead and tin used were of high purity. They were supplied by the American Smelting and Refining Co., who gave the following analyses: Lead: silver, 0.0016 oz per ton; copper, 0.0008 pct; cadmium, 0.0007 pct; zinc, 0.0002 pct; arsenic, 0.0003 pct; antimony, 0.0002 pct; bismuth, 0.0005 pct; tin, 0.0001 pct; iron, 0.0020 pct; lead (by difference), 99.995 pct. Tin: antimony, 0.037 pct; arsenic, 0.020 pct; bismuth, 0.004 pct; cadmium, trace; copper, 0.025 pct; iron, 0.004 pct; lead, 0.020 pct; nickel and cobalt, 0.005 pct; silver, 0.0005 pct; sulphur, 0.005 pct; tin (by .-difference). 99.88 pct. One hundred grams of metal with the desired proportions of lead and tin was weighed out to the nearest one-tenth of a milligram. The mixture was placed in a silica crucible, covered with charcoal, and melted in a reducing atmosphere in a gas-fired furnace. The alloy was well stirred. Chemical analysis of two of the alloys checked closely with the weighed portions. The compositions of the remainder of the alloys were taken directly from the weighings, without chemical analysis.

Jan 1, 1950

By V. F. Zackay, W. A. Goering

ALLOYS of iron and aluminum up to 35 wt pct aluminum are single-phase solid solutions, and are of potentially wide applicability.1-3 In spite of early and continued interest1-4 little progress has been made until recently in the preparation and evaluation of sound alloys containing more than 6 wt pct aluminum. Vacuum-melting techniques for the production of ductile Fe-A1 alloys have been described recently.1-7 A. procedure for air melting these alloys is presented here. Low-carbon iron is induction melted without a slag in a rammed magnesia crucible. At the beginning of melt-down, aluminum pig (99.95 pct Al), charged in a clay-graphite bottom-pouring crucible is placed in a pot furnace at 1800°F. The primary deoxidation of the molten iron after melt-down is effected by the addition of 0.1 pct aluminum and 0.5 pct manganese. (Hilty and Crafts" have reported a significant increase in the deoxidation efficiency of the aluminum and manganese combination over that of the aluminum alone.) A more drastic deoxidation designed to reduce the oxyen content to the lowest possible level is accomplished by plunging metallic calcium to the bottom of the melt. This is done by wiring small cubes of the metal to a steel rod. A circular shield larger than the diameter of the crucible opening is attached to the rod so that any spa'ttering of the molten metal will not endanger the operator. Since the temperature of the molten metal is above the boiling point of calcium, the bath is vigclrously purged by calcium vapor. It is believed that the calcium-vapor treatment permits a homogeneous distribution of calcium in the melt. Owing to the vigor of the reaction the temperature of the molten metal should be kept below 2900°F prior to the calcium addition. A total of 0.05 pct calcium is added in two stages in this manner. The second calcium deoxidation is made just before charging the molten aluminum into the iron, in order that an excess of calcium be present for the remainder of the melt. The aluminum, which has been removed from the holding furnace, is then hydrogen degassed by bubbling chlorine through a quartz tube immersed in the molten aluminum. The hydrogen-chlorine reaction is an exothermic one preventing the solidification of the aluminum during the 5-min chlorination. Approximately 0.1 pct calcium, based on the amount of aluminum, is then added to the aluminum. A further excess of calcium is introduced into the melt in this manner. The oxide dross is removed, fluorspar is added to the molten iron, and the molten aluminum is poured through the fluorspar slag. The fluorspar should be dried thoroughly prior to its use, as any water present will react with the aluminum. Aluminum oxide formed during the pouring operation reacts with the fluorspar slag to form gaseous aluminum fluoride and calcium oxide. A forced-draft ventilating system is required for this operation as aluminum fluoride is toxic. As soon as the molten aluminum has been added, vigorous manual stirring of the melt is required because the slag-aluminum oxide reaction is highly exothermic and tends to take place near the top of the melt. The combination of high temperature and the slagging action of the fluorspar quickly erodes the crucible at the slag line if the aluminum is not stirred uniformly into the melt. It has been found that at least 4 min of manual stirring combined with induction stirring are necessary to ensure homogeneity. The power is shut off 1 min prior to pouring to allow metal and slag to separate. As much slag as possible is removed from the melt, which is then poured directly into cast-iron molds. A mold wash of aluminum oxide is used to prevent ingot sticking. For slab ingots which are to be rolled into sheet, a carbon-tetrachloride vapor atmosphere or a chlorinated-pitch mold wash is desirable, as the aluminum oxide formed in the pouring operation is subsequently removed by the chlorine in the presence of carbon." As in vacuum melting, a pouring temperature of about 2900°F is recommended. Adequate hot-topping is important as iron-aluminum ingots are subject to very deep piping. Ingots are removed from the molds and buried in vermiculite, where they are allowed to cool slowly to room temperature. The ingots are radiographed,

Jan 1, 1959

By Irving Cadoff, Kurt Komarek, Edward Miller

Barium can be purified by equilibration with titanium. The melting point of barium was found to be 726.2° i 0.5 °C. The room-temperature lattice parameters of BaTe and Bask are 7.004 * 0.002A and 6.600 * 0.002A. Melting points for BaTe and Base were found to be 1510° * 30°C and 1830° ± 50°C, respectively. HIGH-purity barium and its compounds are difficult to prepare because of the reactivity of barium with the atmosphere and the large heats of formation of the compounds. Purification of barium by vacuum distillation,' and the preparation and properties of barium oxide2 and barium sulfide3 have been reported. However, little has been done on the homologous compounds barium selenide and telluride. PURIFICATION OF BARIUM Distilled barium obtained from King Laboratories was used as the starting material. The analysis supplied with the metal showed the presence of: 0.4 wt pct Sr, 0.001 pct Mg, 0.02 pct F, 0.003 pct Cu, 0.005 pct Na and less than 5 x 10-3 wt pct of any other metallic impurity. Analyses for oxygen and nitrogen were not available. Since there is evidence4 that any barium nitride present in the starting material may decompose on distillation producing nitrogen which can contaminate the distillate, further purification was performed. At elevated temperatures, any nitrogen and oxygen present in barium should be removed by reaction with titanium. Assuming that the solubility of oxygen in liquid barium is negligible near the melting point of barium, any oxygen present will be in the form of BaO. Removal of oxygen from molten barium is expressed by the equation: BaO(S)+ TixOy(S) = Ba(l)+ TixO(y+1)(s) where Ti,Oy and TixO(y+1) are solid solutions of oxygen in titanium. At 1000°C, the change in free energy for this reaction is negative for (y+1)/x +y+1) x (100) 17.5 at. pct O.5 Since reaction with commercially pure titanium (containing 0.07 wt pct oxygen) results in a free energy change for the reaction of -19 kcal per g-atom, slight solubility of oxygen in barium would not hinder the oxygen removal. Since comparable thermodynamic data are not available to permit calculation of the partition of nitrogen between liquid barium and titanium, a similar quantitative relationship cannot be obtained. However, on the basis of work by Kubaschewski and Dench,5 complete removal of nitrogen from liquid barium can be expected. Since the melting point of barium is depressed markedly by small additions of nitrogen,' the change in melting point during reaction of barium with titanium was used to follow the purification reaction. MELTING POINT OF BARIUM A 50-g sample of barium was sealed by arc welding under argon into an all titanium crucible provided with a thermocouple well. The melting point of the sample was determined by thermal analysis, using a Pt/Pt-10 pct Rh thermocouple which was calibrated according to National Bureau of Standards specification6. The crucible was then heated for 48 hr at 950°C in vacuum and the melting point redetermined. This procedure was repeated until three successive thermal analyses agreed within ±0.5oC, the limits of error of the analysis. The melting point increased from an initial value of 720.0°C to a final value of 726.2°C. Analysis on samples quenched from 950°C gave a solubility value of 0.004 wt. pct Ti. Assuming that the titanium-barium phase diagram is similar to those of titanium-magnesium7 and titanium-calcium,8 the solubility of titanium in liquid barium decreases with decreasing temperature. Therefore, the solubility of titanium in liquid barium should be less than 0.004 wt. pctat the melting point (726oC), and the effect of dissolved titanium on the melting point would be negligible. Addition of up to 3 wt pct Sr does not significantly change the melting point of barium,7 so that the effect of the 0.4 wt pct Sr in the starting material will also be negligible. The value of 726.2" ± 0.5C obtained for the melting point of barium can be compared .with a determination carried out by Keller and coworkers in low-carbon steel crucibles,' who obtained a value of 725± 1C, using barium purified by fractional distillation. The higher value obtained in the present investigation is indicative of the effectiveness of titanium in removing traces of nitrogen. PREPARATION OF BaTe AND Base The compounds were prepared by direct reaction

Jan 1, 1961

By T. M. Morris, W. E. Horst

W. E. Horst—In regard to the flotation rate being described as "first orcler" for flotation of quartz particles below 65 p in size (or any size studied in this work) in this paper, it appears that the authors' conception of rate equations is not in agreement with cited references. A first order rate equation has as one of its forms the following: a In.=a/a-x=kt where a = initial concentration, a—x = concentration at time t, t = time, and k = constant. The constant, k, has the dimension of reciprocal time which is similar to the specific flotation rate, Q. described by Eq. 2 in the authors' article, as has been previously discussed by Schumann (Ref. 1 of original article). The plotted data presented in Fig. 4 of the article utilizes the specific flotation rate, Q (min.'); however, there is not adequate data given to indicate the order of the rate equation which describes the flotation behavior of the quartz system studied. Results from the experimental work indicate that the relationship between rate of flotation (grams per minute) and cell concentration (provided the percent solids in the flotation cell is less than 5.2 pct and the particle size is less than 65 p) is described by an equation of the first order (R, = k c+", n being equal to 1 in this size range) and the use of the first order rate equation does not apply. Similarly the relationship for other particle size ranges studied is expressed by equations of the second or third order depending on the magnitude of n. T. M. Morris—The authors are to be commended for the experiments which they performed. As they state in their discussion the concentration of collector ion In solution did change with change in concentration of solids in the flotation cell. Since for a given slze of particle, flotation rate increases with concentration of collector until a maximum is reached, the effect of concentration of particles in their experiments was to vary the concentration of collector ions. A collector concentration which insures maximum supporting angle for all particles eliminates the unequal effect of collector concentration on various sized particles and the effect of size of particles and concentration of particles upon flotation rate could be more clearly assessed. I believe that if the authors had increased the concentration of collector to an amount sufficient to attain a maximum supporting angle for all particles they would find that the specific flotation rate of particles coarser than 65 p would be constant with change in the concentration of solids in the flotation cell, and that a first order rate would apply to the + 65 as well as to the —65 p sizes. It might also be discovered when this change in collector concentration was made that the maximum specific rate constant would be shifted toward a coarser fraction than when starvation quantities of collector are used since this practice favors the fine particles and penalizes the coarse particles. P. L. de Bruyn and H. J. Modi (authors' reply)—The authors wish to thank Professor Morris for his kind remarks and for mentioning the influence of equilibrium collector concentration on flotation rate. With a collector concentration sufficient to insure maximum supporting angle for all particles, a first order rate equation may indeed be found to be generally applicable irrespective of size. Such a concentration would, however, lead to 100 pct recovery of the fine particles and consequently defeat the essential objective of the investigation to derive the maximum information on flotation kinetics. To establish absolutely the validity of any single rate equation for a given size range, the ideal method would be to work with a feed consisting solely of particles of that size range. Use of such a closely sized feed would also eliminate the possibility of the interfering effect of different sizes upon one another. The authors do not believe that increasing the collector concentration would shift the maximum specific flotation rate (Q) towards a coarser fraction. Experimentation showed Q to be independent of solids concentration for all particles up to 65 µ in size, whereas the maximum value of Q was obtained in the range 37 to 10 p. Professor Morris contends that the addition of starvation quantities of collector favors fine particles at the expense of coarse particles, but the reason for this is not entirely clear to the authors. The comments by Mr. W. E. Horst are concerned only with the concept of the term "first order rate equation." According to the usage of this term in chemical kinetics, time is an important variable, as is shown in the equation quoted by Mr. Horst. All the experimental results reported by the authors were obtained under steady state continuous operations when the rate of flotation is independent of time. To be consistent with the common usage of the "first order rate equation," it would be more satisfactory to state that under certain conditions the experimental results show that the relation between flotation rate and pulp density is an equation of the first order.

Jan 1, 1957

By L. Delisle

This work represents the first step of an attempt to test the applicability of the electron microscope to the study of subgrain structures in copper. Observations on annealed and deformed single crystals and polycrystalline samples of copper are described. IN the course of study of the structure of fine tungsten wires and tungsten rods with the electron microscope, well defined subgrain structures were observed. The size, size distribution, and orientation uniformity of the etch figures varied widely in different samples. Figs. 1 and 2, electron micrographs of a tungsten wire and of a tungsten rod, respectively, are illustrations of the difference in size and size distribution of the etch figures in different samples of the same metal. The observed differences, as pointed out in a previous paper,' appeared to be related to the heat and mechanical treatments of the samples. They were also consistent with the results reported in the literature on the mosaic structure of metals.' For that reason a program of research was initiated in an effort to obtain more systematic evidence of the possible relation of heat and mechanical treatments to the subgrain structure of metals as observed in the electron microscope. The purpose of this paper is to present observations made on the effect of cold work on the subgrain structure of copper. Procedure Starting Materials: Copper was the metal studied because it can be obtained in a high degree of purity, much information is available in the literature on its properties and its response to cold work and heat treatment, it shows no allotropic change, and it is sufficiently hard to be handled without great difficulty. Two groups of specimens were used: 1—single crystals cast from spectroscopically pure copper and 2—polycrystalline samples of oxygen-free high conductivity copper. Single crystals were studied because it was hoped that the elimination of a number of variables, such as grain boundaries, orientation differences, degree of purity, would simplify the problem and perhaps permit a better understanding of the phenomena that would be observed. The polycrystalline samples were designed to give a general picture of the changes considered. The single crystals were made of copper which analyzed spectroscopically to better than 99.999 pct Cu. They were cast in vacuum, by the Bridgman method, in crucibles made of graphite with a maximum ash content of 0.06 pct. The mold design is shown in Fig. 3. It permitted casting crystals of the size and shape required for the experiments, so that the danger of introducing cold work in the original samples by cutting or other machining would be eliminated. The polycrystalline samples were pieces, 3/4 in. long, cut from a rod of oxygen-free high conductivity copper, % in. in diameter. A flat surface, 1/4 in. wide, was milled along the rods, polished, and etched. The samples were then annealed in vacuum at 850°C for 1 hr. Polishing and Etching: Work previously done on tungsten,' polished mechanically and etched chemically," had shown that: 1—the general appearance of the etch figures of a given sample was not altered by repeated polishings and etchings under similar conditions; 2—variations in the time of etching and the concentration of the etchant changed the definition of the etch figures, but did not alter their general size nor orientation distribution within the limits of observation. Further work confirmed the reproducibility of the subgrain structures observed in, 1—single crystals and polycrystalline samples of copper when polishing and etching were repeated under similar conditions, and 2—specimens of tungsten and polycrystalline copper when electrolytic polishing and etching were substituted for mechanical polishing and chemical etching, respectively. On the strength of these observations, it was felt that, if conditions of polishing and etching were kept constant, changes observed in the subgrain structure of a sample upon deformation and annealing would be attributable to such treatments. For that reason the conditions of polishing and etching were kept as constant as possible. The single crystals were polished electrolytically in a bath of orthophosphoric acid in water, in the ratio of 1000 g of acid of density 1.75 g per cc to 1000 cc of solution, under a potential drop of 1.6 to 1.8 V. Electrolytic polishing was selected to prevent the formation of distorted metal in polishing. The same samples were etched by immersion in a 10 pct aque-

Jan 1, 1954

By Irving B. Cadoff, Alvin A. Machonis

The resistivity, Hall coefficient, Seebeck coefficient, and thermal conductivity were measured as a function of temperature for cation-rich alloy single crystals covering the composition range across the PbTe-SnTe system. Alloying of PbTe with up to 20 pct SnTe was found to have little effect on the energy gap. Above 20 pct SnTe the alloys were "p" type but below this range the sign could be varied by heat treatment. The lattice thermal resistivity of the compounds SnTe and PbTe is raised by alloying one with the other. Z values in the order the interesting values obtained. THE PbTe-SnTe system has several interesting features. For one, PbTe is a useful thermoelectric material and the possibility of improving its figure of merit by alloying with SnTe, an isomorphous compound, has been suggested since these pseudo-binary solid solutions generally have a more favorable ratio of electrical conductivity to thermal conductivity than either of the components.' Other interesting features relate to the conductivity mechanism, band structure, and stoichiometry of the compounds and their alloys. PbTe is a semiconductor with an energy gap of about 0.29 ev2 at room temperature whose conductivity sign and magnitude can be varied from "n" to "p" by controlling the proportion of lead and tellurium with respect to the stoichiometric ratio.3 Excess lead results in "n"-type conduction. SnTe is found to exist only as a "p"-type material of relatively high conductivity. This behavior is attributed to stoichiometric deviation by Brebrick4 but Sagar and Miller proposed that the behavior of SnTe must be due in part to the presence of an overlapped band. An investigation of alloys of this system, therefore, might give additional information which would permit one to evaluate which of the two proposals is the more appropriate one. Abrikosov et al.' studied the room-temperature electrical properties of these alloys and reported data for Seebeck coefficient and resistivity on poly-crystalline alloys. The present work is a more exhaustive survey of the PbTe-SnTe system. Re- sistivity, Hall coefficient, Seebeck coefficient, and thermal conductivity were measured over a wide temperature range for single crystals at 10-pct intervals of lead/tin ratio across the pseudobinary system. The relative concentration of tellurium was controlled so as to obtain metal-ion excesses in all cases. SAMPLE PREPARATION The crystals were prepared by melting elemental lead, tin, and tellurium in weighed proportions in evacuated Vycor capsules. The lead and tellurium were high-purity grades obtained from American Smelting & Refining Co. The tin was supplied by Comico. The proper calculated proportions of lead, tin, and tellurium were weighed and charged into prepared Vycor capsules prior to evacuation. The capsules were prepared from 15-mm Vycor tubing. A sharp point was worked on one end of the tube. A pyrolytic graphite coating was deposited on the Vycor walls by heating the tip to 800°C in an atmosphere of acetone-saturated argon. An additional coating of graphite was deposited on the pyrolytic coating from an Aquadag suspension. Above the coated tip the tube was reduced in diameter to form a constrictive neck. To avoid scratching the graphite coatings the charge was placed in the tube above the constriction. After a low-temperature bake, the evacuated capsule was sealed. On subsequent heating the charge melted down into the lower portion of the capsule. The crystals were grown by lowering the capsule through a Bridgman-Stockbarger furnace. The lowering rate was 1 in. per 8 hr. The upper portion of the furnace was set for 950°C and the lower portion for 800°C. In general the yield of single crystals was about 25 pct. The mixed compositions were, as expected, the most difficult to grow. The finished crystals were sectioned into 5/8-in. slices. The tip, end, and middle slices from each crystal were analyzed by X-ray fluorescence to determine the lead-to-tin ratio. The resulting values were used to plot a composition vs distance plot for each crystal. Slices were selected from each crystal, with the aid of the composition plots, to cover the complete range of compositions at 10-pct intervals. In general, the slices selected were taken from the seed end of the crystal where the longitudinal segregation (as determined from the X-ray fluorescence analysis) was a minimum. Laue single-crystal analysis and metallographic analysis was used to verify if a slice was single or polycrystal. Any grain boundaries were clearly visible in the as-cut and polished condition. In ad-

Jan 1, 1964

By J. L. Huitt, B. B. McGlothlin, J. J. Day

Laboratory tests were made with pure minerals and actual reservoir rock samples to study the effects of hydrothermal (steam m hot water) treatments on reservoir rock properties. These tests showed that hydro-thermal treatment of many reservoir rocks can result in significant rock softening. The softening was attributed primarily to the partial destruction of dolomite and kaolinite and the synthesis of montmorillonite in the presence of excess silica. In many cases, the softening was great enough to cause considerable healing of propped fractures; therefore, a serious reduction in welt productivity could result. In other tests it was found that the addition of ammonia to a hydrothermal treating fluid in a concentration as low as 0.013 Ib/lb of water not only could prevent rock softening but could cause rock hardening. The results of X-ray diflraction analyses of rock samples showed that when ammonia was added to the treating fluid, ammonium-mica and analcite were formed instead of montmorillonite. No significant permeability damage was observed in the sandstones that were subjected to the ammonia-hydro-thermal environment; in some sandstones, permeabifity improvements resulted. INTRODUCTION As the use of steam or hot water becomes more prevalent in well stimulation methods. the need for information on the effects of such treatments on reservoir rock properties becomes increasingly apparent. Several works have been published on high-temperature changes in rock properties,',' but these are more applicable to in situ combustion operations than to steam or hot water injection processes. The mineralogical literature contains many publications which report on the changes occurring with various pure minerals in hydrothermal systems. A review of this literature denotes the ease with which entirely new, crystalline mineral phases can be synthesized from other minerals in hydrothermal environments at temperatures, pressures and residence times typical of those encountered in oilfield thermal recovery or stimulation processes. Discussions of many of these experiments are given by Deer et al. Grim,' Roy et al., Zen\ and Hawkins.' One of the most significant of these pure mineral studies is the hydrothermal synthesis work of Levinson and Vian" in which montmorillonite was synthesized from naturally occurring minerals; i.e., kaolinite, quartz and carbonate minerals (particularly dolomite). These reactions occurred at 575F in only 2 days and at 300F in 5 days. These results may be applicable to petroleum reservoir rocks since the minerals studied were those which are commonly found in sandstones. Furthermore, the environmental conditions imposed in the studies were very similar to those involved in thermal stimulation of petroleum reservoirs, e.g., steam or hot water injection. Other studies have suggested that weak rocks could be hardened by "electrochemical induration", a process in which an electric current is applied to a clay-containing rock body. These tests can be regarded as hydrothermal treatments since they were conducted in some instances with aqueous solutions and since clay temperatures during the electrical treatment reached a maximum of about 100C. Although a number of studies of the reaction of pure minerals have been reported, very little has been published on the reactions of petroleum rock-hydrothermal systems. No work has been reported on preventing the more detrimental rock changes in rock softening which might occur during the injection of steam or hot water into reservoirs. The studies described in this paper were conducted to provide such information. EXPERIMENTAL APPROACH The laboratory tests included studies of the effect of hydrothermal treatment on core samples from several different reservoirs. The hydrothermal treatments (simulated steam treatments) were conducted with distilled water at 575F, for the most part, for periods of 2 to 6 days. This temperature level was selected because it represented that temperature which would probably prevail in several cases under consideration for steam injection projects. The core samples, as well as the pure mineral samples, were contained in high-pressure stainless steel, autoclave-type pressure vessels. The effects of the hydrothermal treatments were evaluated by measuring the penetrometer hardness, formation rock embedment strength and permeabilities of the core samples before and after the treatments (Fig. 1)'" In addition, the mineralogical changes in the specimens were studied by X-ray diffraction. Concomitant with the core sample studies, the mineralogical changes were studied in greater detail by conducting hydrothermal synthesis experiments with pure minerals at similar temperature levels and residence times. For the most part, samples of finely-crushed pure dolomite.

By T. E. Tietz, J. E. Dorn

Activation energies for creep of copper at intermediate temperatures, where crystal recovery was negligible, were determined by the simple technique of rapidly alternating the test temperature between and T2 (T2 = TI + about 10°K) throughout a constant stress creep test. The activation energy for creep H was found to be 37,000± 3,000 cal per mol, independent of stress and strain. The same creep laws as have been previously established for high temperature creep were found to be valid for creep at intermediate temperatures. But the AH was found to be lower than that for self-diffusion in the intermediate temperature range whereas it is known to be equal to that for self-diffusion at high temperatures. IT is now well established that creep at high temperatures can be correlated by the functional relationship'-" e = f(?) s = constant [I] where E is the total plastic strain, f is the function that depends on the stress, ? = f e -- dt, t is the duration of test, e is the base of natural logarithms, AH is the activation energy for creep, R is the gas constant,T is the absolute temperature, and s is the stress. Thus, identical values of are achieved during creep under a given stress at two alternate temperatures at the same total strain. At the same strain therefore where subscripts refer to the two alternate temperature conditions of test. Consequently, the activation energy for high temperature creep is readily obtained with the aid of Eq. 2. Activation energies so obtained have been observed to be insensitive to the creep strain at which they are evaluated, the applied stress, grain size, minor alloying additions,'-' cold worked state, and the presence of thermally stable dispersions of intermetallic compounds in an a solid solution matrix Furthermore, the activation energy for high temperature creep is very nearly equal to that for self-diffusion in all cases where adequate data are available for comparison." " The apparent identity of the activation energies for high temperature creep and self-diffusion strongly suggest that high temperature creep arises from a dislocation climb process. This hypothesis is further strengthened by the fact that the energy of activation for high temperature creep is insensitive to the applied stress," and by the observations that the correlation suggested by Eq. 1 cannot be ex- tended to temperatures below those for rapid crystal recovery. When using the activation energy for self-diffusion, Eq. 1 fails to give the required correlations between creep curves at various intermediate temperatures.' This suggests that the dislocation climb mechanism for creep might be superseded by some alternate mechanism in the intermediate range of temperatures. This investigation was initiated in a preliminary attempt to ascertain the type of creep law that might be valid in the intermediate range of temperatures. Special consideration, however, was given to the determination of the activation energy for creep in this range because the Becker-Orowan', " and the Mott-Nabarro10 theories for transient creep suggest that the activation energy should increase

Jan 1, 1957