Search Documents

By Eugene P. Pfleider

Research indicates that the cube diamond is a superior stone for drill bits. It can be oriented to combine a long cutting edge with structural strength and high resistance to wear. Test bits set with preferred orientation give double the bit life at astoundingly low diamond loss in comparison to oriented octahedral diamonds. A PROGRAM of research on the orientation of diamonds in drill bits has been under way for several years at both the United States Bureau of Mines Experimental Mine at Mount Weather, Va., and the School of Mines and Metallurgy of the University of Minnesota. Reports on past work done both in the laboratory and the field are available in the technical press.1,3,4 The results of such drilling, done under comparable conditions, show that bits having diamonds oriented in a direction that combines structural strength and greatest hardness not only can advance somewhat faster than random set bits but can do this with a unit diamond loss of 50 pct or less. Several bit manufacturers have initiated the training of diamond setters in the principles of orientation on the basis of the above-mentioned research results. The basic information on the crystallography and hardness variation of the diamond was presented in an earlier paper,' which pointed out that the diamond is several hundred times harder along certain directions and certain faces than on others. The same article discussed the drilling results obtained with a group of nine bits having octahedron diamonds set with on-point, positive (gouge) rake, and negative (drag) rake orientations. The testing of oriented cube diamonds is an extension of this research program, employing the same procedures and equipment (Hy Mac hydraulic drill unit, EXT diamond core bits, St. Cloud Pink granite) as previously described. This current work covers the test experience of seven bits set with cube diamonds running approximately 10 stones per carat. The individual stones were near perfect cubic form; hence it was simple to orient them in any desired direction. The cube is a comparatively rare crystal form of the diamond, although considerable numbers are produced from the Congo. It is understood that most of the cube diamonds are retained in Africa, where they are either used locally for diamond bit manufacture or ground up to make powder. They have been considered to be an inferior stone for drilling purposes.

Jan 1, 1954

Masjid-i-Su1aiman.—There have been no new developments in the Masjid-i-Sulaiman field during the year. Drilling, deepcning and acidizing operations for maintenance of production havc continued normally. Reservoir conditions have been unchanged, the rate of fall of dome prcssure remaining very low—at about 0.4 lb. per sq. in. per million tons net production. Drilling on the Lali structure northwest of Masjid-i-Sulaiman has continued but oil has not been encountered in commercial quantities. Haft Kel.—The progressive drilling program extending the production capacity of the Haft Kel field was completed carly in the year and the field is now on a routine maintenance basis. Drilling has continued on the white-oil springs structurc northwest of Haft Kel. Naft-i-Shah.—No developments of interest have occurred in Naft-i-Shah field. Offtake is for local markets only. A further large produeer was completed during the year. Gach Saran.—By the end of 1939, work on plant and pipe lines to put, the field on a production basis was approaching completion. Two substantial producers were also drilled in the initial production area. Pazanun and Agha Jari.—No further drilling was carried out on the Pazanun structure during the year, gas only having been obtained to depths exceeding 8000 ft. On the adjacent Agha Jari structure, however, a second satisfactory oil producer was completed.

Jan 1, 1940

Masjid-i-Su1aiman.—There have been no new developments in the Masjid-i-Sulaiman field during the year. Drilling, deepcning and acidizing operations for maintenance of production havc continued normally. Reservoir conditions have been unchanged, the rate of fall of dome prcssure remaining very low—at about 0.4 lb. per sq. in. per million tons net production. Drilling on the Lali structure northwest of Masjid-i-Sulaiman has continued but oil has not been encountered in commercial quantities. Haft Kel.—The progressive drilling program extending the production capacity of the Haft Kel field was completed carly in the year and the field is now on a routine maintenance basis. Drilling has continued on the white-oil springs structurc northwest of Haft Kel. Naft-i-Shah.—No developments of interest have occurred in Naft-i-Shah field. Offtake is for local markets only. A further large produeer was completed during the year. Gach Saran.—By the end of 1939, work on plant and pipe lines to put, the field on a production basis was approaching completion. Two substantial producers were also drilled in the initial production area. Pazanun and Agha Jari.—No further drilling was carried out on the Pazanun structure during the year, gas only having been obtained to depths exceeding 8000 ft. On the adjacent Agha Jari structure, however, a second satisfactory oil producer was completed.

Jan 1, 1940

By David C. Yang

INTRODUCTION Over the world, and especially in the United States, there is increasing dependence upon progressively lower grade ore deposits. These lower grade ores are frequently difficult or impossible to process due to complex mineral assemblages being very finely disseminated. Thus, many of the conventional mineral concentration methods are not applicable to these ores. For the last few decades, research in the more exotic mineral processing techniques has been conducted, both in universities and in governmental and industrial laboratories. Since its inception, the Institute of Mineral Research of Michigan Technological University (MTU) has devoted much of its attention to the problems of processing refractory, low grade ores. Recently a new flotation system was developed which shows promise of being applicable to a broad range of ore types. This process has been the subject of two allowed patent applications. This paper describes the details of such a flotation system which is potentially useful for treating ultrafine minerals. Some highlights of the testing program on a variety of iron ores and a group of lithium-bearing ores will be presented. EXPERIMENTAL PROCEDURES Both iron and lithium ore flotation treatments followed the same general procedures, with minor differences in pH and in reagent dosages. The method is rather simple, efficient and economical from the standpoint of recovery and the cost of reagents consumed.

Jan 1, 1979

By Arthur E. Bousu, C. T. Eddy, L. W. Eastwood

THE recrystallization and grain-growth phenomena of cold-worked metals have considerable industrial importance because of their role in the fabrication of metals. For this reason, and because of the general academic interest in the subject, these processes have received considerable attention since the time of J. E. Stead's paper1 on The Crystalline Structure of Iron and Steel. There are considerable differences of opinion regarding the theory of recrystallization and grain growth and also differences in the observation of the modus operandi of the processes themselves. The value of many of the existing quantitative data on grain growth is decreased by the failure to distinguish between the grain sizes just after complete recrystallization and those resulting from coalescence. For this reason also, the value of the diagrams of stable grain sizes, like those produced by . Bass and Glocker2 and Czochralski3, is lessened in so far as an interpretation of the facts of recrystallization is concerned. It is hoped that the data presented in this paper will help to clarify and to simplify the facts relating to recrystallization, and at the same time will show that some of the present-day conceptions are untenable. A paper on the theory of recrystallization with additional data will be completed in the near future by the writers.

Jan 1, 1935

By E. H. Jr. Dix

DURING an investigation of high-strength manganese bronze by the Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received the early consideration of scientific research. The diagram, according to the most recent work,1 is shown in Fig. 1. The disputed questions involve the termination of the beta field and the line at 470° C. The earliest experimenter, Roberts-Austin, detected an arrest in some of his cooling curves at approximately this temperature and ascribed them to the formation of a eutectic; it has since been proved that there are no eutectics in this series. Shepherd2 was unable to detect any thermal arrests at this temperature; his diagram was essentially as shown in Fig. 1, except that the line at 470° C. was omitted and the beta phase carried down to normal temperatures. Later, Carpenter and Edwards,3 by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the beta constituent into a eutectoid of alpha and gamma. Microscopic evidence of the formation of the eutectoid is doubtful and it seems more likely to be due to an allotropic change in the beta constituent as shown by Fig. 1. At least for practical purposes, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather than alpha plus an unresolvable eutectoid of "apparent beta" as it has often been called.

Jan 5, 1922

By B. L. Averbach

Recovery and primary recrystalliza-tion in cold worked metals are usually considered as two competing processes. Some of the effects which usually accompany recovery are: alleviation of stress corrosion tendencies, changes in thermal emf,1 damping capacity,2 electrical resistivity,2 and magnetic properties,3 and only minor changes in hardness or the related strength properties. During primary recrystalliza-tion new unstrained grains are formed at the expense of the strained matrix. These new grains eventually become visible metallographically, and nucle-ation and growth kinetics have been indicated for this process.4,5 Frequent attempts have been made to study the cold-working phenomenon by observations on the line broadening by X ray diffraction patterns. Relatively few measurements of line intensities have been made, although Brind-ley and his collaborators, 6,7,8 by means of film techniques, compared the intensities of cold worked Cu, Ni, and Rh patterns with those from chemically precipitated powders. These precipitated powders were presumed to be strain free, and it was found that the intensities for the cold-worked materials progressively decreased as the Bragg angle increased except for the first line, where there was an increase due to reduction in extinction. This was interpreted as a randomness in atomic position induced by cold work. Such randomness is similar to that caused by thermal agitation and has been described as "frozen heat" displacement of 0.08-0.10 A from the mean atomic position. In a recent study9 on the effect of cold work in metals on their powder pattern intensities, the changes in integrated intensity for heavily cold worked alpha brass were observed as a function of the annealing temperature. These measurements were made with a manually operated Geiger-counter spectrometer using CuKa radiation monochromated with a rock salt crystal. Intensity measurements were made with a scaling meter over small intervals of angle, and the equipment was so arranged that the diffracted and incident beams made equal angles with the specimen. Intensities could be compared directly by simply interchanging specimens, and comparisons from day to day were made with a standard whose line intensities did not change on aging. It was shown that a cold worked alpha brass standard was stable for at least a year. Table 1 indicates the results of the integrated intensity measurements on a 70 Cu-30 Zn brass. In the sample preparation, a brass plate was first cold rolled 50 pct and then filed, screened to —325 mesh, compacted into briquettes at a pressure of 60,000 psi and finally annealed for one hour at various temperatures up to 400°C. The briquetting pressure did not seem to influence the integrated intensities, and most of the cold work was introduced by the filing. Although this method of cold work is not quantitative, it was used to obtain random orientation (and thus uniform diffraction lines) in order to make accurate measurements of integrated intensity. Back reflection patterns were taken in each case to check the uniformity of the lines, and from the observed line broadening it was apparent that this type of plastic deformation was quite severe. Care was taken to traverse the entire background of the pattern and to assign to each peak the total intensity above this background. The bases of the diffraction lines were quite broad and spread out over several degrees, even for the narrow peaks. The theoretical intensities were calculated to include a temperature correction, a dispersion correction, and a Lorenz- polarization factor corrected for the crystal monochromated beam. In Table 1 it was necessary to match the calculated and observed values at only one point, and the rest of the experimental values were converted directly to this arbitrary scale. The integrated intensities in Table 1 are listed in arbitrary units, and the accuracy was sufficient to reproduce any of the measured line intensities to within + 1.5 units. It is evident that the percentage error on the strongest line (111) was quite low. The calculated values and the observed intensities for the cold worked material matched reasonably well. As the annealing temperature was raised, however, the intensity of the strongest reflections, particularly the (lll), decreased measurably. Since the background intensities of all of these patterns were identical, such behavior could be interpreted as a primary

Jan 1, 1950

By Douglas Bunting

With the gradual exhaustion of the upper veins in the anthracite coal-fields, the problem of mining at greater depths acquires increasing importance and demands the consideration .of a number of important factors, one of which is the greater earth-pressure and the consequent necessity of stronger support for the roof. Under the pillar-and-chamber system, almost exclusively followed in the Northen anthracite-field, the highest economy in mining is generally secured by leaving, on first mining, pillars only sufficient to support safely the overlying strata. As to the necessary size of such pillars, the opinions of mining experts are widely divergent. In establishing the width of chambers and pillars, the thickness of vein and its depth below the surface have received little consideration. For instance, it has been quite usual to work both overlying and underlying veins with the same width of chambers and pillars, when the lower vein was two and one-half times as thick, and twice as far below the surface, as the upper. In view of the generally-accepted theory that the crushing-strength of coal-pillars of the same base-area becomes less with increased height, it is probable, in this instance at least, that the moat economical mining has not been secured. This question of adequate pillar-support is economically less important down to about 800 ft. than at greater depths; and it is with reference to mining at these greater depths that the study of the subject here presented has been prompted. The necessity of leaving larger pillars, involving greater mining-costs per ton and also smaller yields per acre, is one of the troubles of deep working. To mine without leaving adequate pillar-supports will result, sooner or later, in a squeeze. Limited areas, it is true, have been mined at certain widths of

Jan 1, 1912

By Augustus Locke

The paper has two parts: the field argument and the microscopic argument. The field argument indicates that either the deep chalcocite has replacea sulfide of extraordinarily easy replaceability or it is hypogene. The microscopic argumentindicates that this sulfide, if it existed, must have been hypogene bornite; that this bornite must so excel known bornite in replaceability as to constitute a new variety; that the existence of this new variety is wholly unsupported by evidence; and that the deep Butte chalcocite is therefore hypogene. IN 1900, when the public first heard of "secondary enrichment" the Butte chalcocite seemed clearly supergene. Mining, through successive regions of leached capping, bonanza sulfide, and sulfide less rich, had paused at lean bottom levels which, though chalcocite-bearing, suggested the waning of copper. The deepest chalcocite, at 1500 ft., was yet too shallow to disturb the supergene hypothesis. But, with deeper mining, lean levels yielded to fat ones. Here and there they showed, within the same vein, an inverted distribution, chalcopyrite above and chalcocite below. To the miners' astonishment, they carried chalcocite, unaffected by cross faults, on an independent course to the depth of 2500 ft. The pattern of ore distribution, hitherto revealed only in fragments, was now appearing in perspective, and, in the depth of the chalcocite, was beginning to make Butte differ from all districts where the chalcocite is indubitably supergene. The idea of hypogene origin at length came into favor; by 1913, when Sales1 advocated this origin, the argument had become a powerful one. This argument rested on field evidence; but, already, there was beginning to emerge microscopic evidence not included in this arugment. Especially pertinent was the proof that (1) The deep chalcocite lies in-mixed with bornite, often microscopic; (2) the deep chalcocite often replaces bornite; and (3) replacement of bornite by chalcocite is accom-

Jan 3, 1924

By R. S. Hooper

IN attempting to describe recent mining developments at the Bunker Hill mine, it may be well to recall first the old days of hand mining when holes were laboriously drilled by hand to a maximum depth of three feet, and were shot one or two at a time, in order that the miner could take advantage of every slip, crack or bedding plane, and so save as much drilling as possible. Broken muck, of course, was loaded by hand shoveling into wheelbarrows or small cars, and heading advances or stope ton¬nages were governed by the number of men that could find room to work in any given place. The first big improvement over these old methods was the introduction of the reciprocating type of air-powered rock drill. This innovation, crude as it was, enabled the miners to set up a machine and drill a complete round of holes in one shift; but broken muck was still loaded by hand, and the size and rate of advance in headings were limited by time required to remove the broken rock. The next improvement of consequence was the appearance of the hammer-type rock drill, which greatly increased drilling speed over the reciprocating type, and made possible the completion of a full cycle in one shift, by the use of crossbars in headings, and permitted drilling and mucking to be carried on at the same time. Rock drills continued to improve as time passed, and finally the smaller and more efficient mucking machines appeared on the scene, and it became possible to muck out a round of broken rock and have a clean setup for one or more drill columns and machines. A complete cycle of mucking, drilling, and blasting was completed in one shift with an average advance of five feet. These conditions prevailed for several years, but as the mine grew deeper, the distances to transport the workers grew longer, and this fact together with the shortening of the working day, soon presented the problem of attempting to complete a cycle of operations in a shift of only six hours at the working faces. Anticipating this condition, the operating heads at the Bunker Hill had started an intensive study of more and better mechanization, and over a period of comparatively few years have adopted and placed in service methods and machines that make it possible for a three-man crew to consistently advance headings seven by nine feet in cross section, at the rate of eight feet, and more, per shift, doing all the mucking, switching, drilling and loading. These improvements consist of the following major items: I. The development of a light, flexible, easily transported jumbo equipped with pneumatic columns (Fig I), that has decreased the "setting up" and "tearing down" time an average of 1 1/2 hr per shift, or 25 pct of the available working time. These jumbos were developed at the Bunker Hill mine by members of the staff and consist of two pneumatic columns attached to a suitable carriage. They fold

Jan 1, 1947

By K. D. Weverstad, J. E. Cleveland, J. C. Franklin, J. W. Black

A mined-out stope being backfilled with classified mill tailings was continuously monitored, both upstream and downstream, to determine the radon concentration associated with the mill tailings. The radon monitoring was done before, during, and after the backfill operation. Data taken during weekends when no mining activities were influencing the radon concentration showed a 90 percent reduction in radon discharge from the stope after being backfilled. Water used to mix with the classified sands showed an increase in the heavy metals concentration immediately after seeping from the inplace sand. However, the water used in backfilling is less than ½ of 1 percent of total mine water discharged. The change in contamination is not measurable at the pumping station.

Jan 1, 1982

By H. A. Burgman

During in situ uranium mining using ammonium bicarbonate lixiviant, the ammonium exchanges with cations on the ore's clay. After mining is complete, the ammonium may desorb into post-leach ground water. For the particular ore studied, other elements (uranium and selenium) that are mobilized during the leaching process, have also been found in post-leach ground water. Laboratory column tests, used to simulate the leaching process, have shown that aluminum chloride can rapidly remove ammonium from the ore and, thus, greatly reduce the subsequent ammonium leakage level into ground water. The aluminum chloride has also been found to reduce the leakage levels of uranium and selenium. In addition, the aluminum chloride treatment produces a rapid increase in permeability.

Jan 1, 1985

The housing of labor and sanitation at mines in India are difficult problems to solve because-no more than two or three castes will accept the same conditions, and conditions suitable to one coal-field are not applicable to other fields. It is also necessary to consider the financial standing of the different companies. The European companies, which pay 30 per cent. and more dividends, can erect more suitable houses than the Indian companies, which are just able to keep their heads above water. The Santhal will not live in a bucca-roofed house as a permanent dwelling, and both the Santhal and Koras have an aversion to living in a line of attached huts. They have forsaken a whole, line of houses in one of which a case of sickness or death has occurred, and those houses were afterward considered unfit by all other classes of natives. The Santhals, Koras, and Douri castes will not take drinking water from a stand pipe; wells must be furnished. When well water is not available, these people will take water from the nearest pool or tank regardless of whether or not the water is stagnant. The well tops should not he completely enclosed, nor should there be a drain around the top. The ground should slope away from the well. In the Girieih coal fields, the miners have a great objection to pucca floors; they prefer earth which is lapped, easily cleaned, and renewed. As it is customary for the miner to build his own house, the company supplying the roofing material, he takes a special interest in it, keeps it in order, and hesitates to leave it. Each house is surrounded by its own bit of land, which the inmate cultivates.

Jan 12, 1918

By Warren E. Holland, Leon H. Robinson

The pore pressure must be included in any discussion of the state of stress within a rock. Rock cylinders at elevated stress levels, loaded uniaxially to a stress less than the yield strength, can be fractured by holding the constraints constant and increasing the pore fluid pressure. This can be described in terms of the Mohr envelopes using effective stresses. The effective stress concept can simplify data with various confining and pore pressures. When the pore and confining pressures are equal, the pore pressure appears to be totally effective in reducing the confining pressure effects. The area over which the pore pressure acts has been the subject of some prior discussions. Terzaghi 1 defined boundary porosity as ". . . the ratio of that part of the area of the potential surface which is in contact with the interstitial liquid and the total area of this surface." His method of calculation included a discussion of splitting failure which was objected to by Mr. Kessler, National Bureau of Standards. The values calculated by Terzaghi were close to unity. Leliavsky,2 using unjacketed cement cores, reported that the interstitial fluid pressure appeared to act upon about 92% of the surface of failure. He concluded: "The fraction of the area of cross-section over which the internal pressure acts can therefore have nothing to do with ordinary porosity, and the results of the experiments tend to support Professor Terzaghi's views." In 1947 Balmer3 determined the boundary porosity of concrete when the confining and pore pressures were equal. He also found values close to unity. In 1948 McHenry4 published some of the results from the same equipment and included the first data in which the pore pressure

Jan 1, 1970

By Frederick G. Bulkley

That portion of the geological structure of the Leadville district which rests upon the Archæan is made up of sedimentary beds of Silurian and Carboniferous formation, consisting of many conformable strata of limestones, quartzites, and shales, which have a total present thickness of about five thousand feet. Interbedded with these strata are found, under somewhat fixed lams of regularity, sheets of intrusive igneous rock,' varying in thickness from a foot or two to several hundred feet. These consist for the most part of various types of felsite rocks, classed, by the sanction of common and long-continued usage, under the general term of porphyries. Mr. S. F. Emmons, in the abstract of his " Report upon the Geology and Mining Industry of Leadville," says in this connection : In their mode of occurrence the type-feature is that of intrusive masses, which are developed on a scale of unprecedented magnitude, and follow certain horizons with remarkable regularity.... It is probable that this mode of occurrence of eruptive rocks, viz., as intrusive masses which originally did not reach the surface but were forced up to a certain horizon and then spread out bettween the beds, is far more common than has hitherto been suspected by geologists. It is difficult to conceive of the conditions under which a fused mass could pry open strata to a width of one thousand feet or more, overcoming the weight often thousand feet of superincumbent rocks, and spread itself out in a continuous sheet between the beds to a distance of ten miles beyond the point or line of eruption. That they did exist, however, can be clearly demonstrated in this region.... In one single section over fifteen sheets, many several hundred feet thick, were counted between the Blue Limestone and the top of the Carboniferous. The region here under discussion is made up of a series of great

Jan 1, 1885

By Roberto Fernandez

Want of knowledge on the part of experts from abroad respecting the amalgamation-system, known as the Mexican or patio process, has been the cause in this country of trouble to many foreign mining companies. This process has not been looked upon by their managers as a satisfactory method of treating silver-ores, and they prefer to employ others, which, although more modern, and often more profitable in other countries, have not proved to be so under the exceptional conditions of this country, where labor is cheap and paid in silver, while fuel is very dear. The cause of this error of judgment is probably the inexact information which has been furnished by several authors respecting the economical results of the patio process. This treatment is not suitable for silver-ores of every kind. Simple sulphides of silver are best adapted to it, and, next to these, the combinations of complex sulphides, viz., pyrargyrite, polybasite, stephanite, proustite, etc. Chlorides, bromides and iodides of silver are considered rebellious ; argentiferous galena, blende, bournonite, as also argentiferous arsenical pyrites of iron and copper, are absolutelg unsuited to this treatment. Experience has proved that high-grade ores do not give as satisfactory results as those of mediurn grades, as, for instance, carrying from 1 to 2 kilos of silver per metrical ton. The patio process, as actually practiced in this district, comprises the following operations: 1. The ore is crushed in a dry state in a roller-mill, reducing it to pea-size, from which uniform samples, and, in consequence, correct assays, can be obtained. 2. It is then thrown into the arrastra, and pulverized with water, so fine that it will pass through an 80-mesh screen.

Jan 1, 1900

By G. D. Tranter

THE importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the -pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint .of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth .history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By H. M. O?Harra

Experiments have shown that the use of enriched air would be of particular benefit in the roasting of zinc ores for the manufacture of sulfuric acid. Enriched air increases capacity of furnace, decreases fuel consumption, and increases SO2 content of roaster gas. THE work here described had for its purpose the procuring of data from which some quantitative estimate might be made of the results obtainable by using oxygen-enriched air in roasting zinc ores on a commercial scale. The principal metallurgical advantages of using enriched air in roasting zinc ores would be: 1. The rate of roasting would be increased, with consequent gain in the capacity of the roasting furnace. 2. As less air would be required for roasting, the volume of hot gases leaving the furnace and the heat carried out of the furnace as sensible heat in these gases would be less per ton of ore roasted; partly for this reason and partly because of the increased quantity of heat generated in the furnace by the larger amount of ore that could be roasted, the consumption of fuel by the furnace would be lessened; and by the use of air sufficiently enriched with oxygen the necessity of using fuel might be entirely obviated. 3. Roaster gas having a higher SO2 content could be produced; this would make possible greater capacity and more economical operation of the sulfuric-acid plant. Certain phases of the application of enriched air to roasting can be worked out only by experimenting with a furnace of commercial, or at least semicommercial, size. Thus the precautions necessary to secure proper distribution of heat in the furnace;1 the volume of enriched air,

Jan 3, 1924

By L. C. Noakes

In 1947, only a year after its own establishment, the Australian Bureau of Mineral Resources, Geology and Geophysics formed a Mineral Economics Section. Originally, this Section consisted of a mineral economist, four geologists and three auxiliary employees. Then, in 1954, it was reorganized into a professional body of six members, all mineral economists, one of whom was the chief mineral economist. At this time, a mining statistical officer from the Bureau of Census and Statistics was attached to the Section to bring about a closer liaison between these two agencies. The addition of another mineral economist in 1961 brought the Section's professional staff to its present strength of seven. In recent years, the Mineral Economics Section has gained considerable support by becoming part of the Mineral Resources Branch of the Bureau of Mineral Resources. This Branch, which has the general role of monitoring the performance of the mineral industry in Australia, has two other specialized sections- Mining Engineering and Petroleum Technology-which bolster and complement the Mineral Economics Section.

Jan 1, 1970

By R. M. Daelen

Mechanical science is severely tested by the demands of the iron manufacture for the varied apparatus needed to transport and to treat raw materials and products. Water has long been a favorite means of transmitting pressure for such purposes, because of its own incompressibility. Further advances in its use are the more to be expected, since mechanical improvements have steadily tended to overcome the difficulties formerly encountered in the employment of great hydraulic pressures. So long as the pressure is not higher than that which requires for plungers, etc., only ordinary stuffing-boxes, with hemp or other similar packing, the necessary arrangements for the production and transmission of the water-pressure without leakage are very simple. But when this limit (which is, for most purposes, 50 kilos to the square centimeter) is exceeded, new conditions of construction arise, which are met in various ways, and which justify a primary division of hydraulic presses into low-pressure and high-pressure respectively. The former are used in lifting and moving weights, and employ pressures as high (in extreme cases) as 100 kilos per square centimeter; but at this point the friction between piston and hemp-packing is so great that the use of cup-leathers is already preferable. Beyond 100 kilos it becomes a necessity. The range of practicable tight packing which follows is considerable, extending to about 1000 kilos; but "high pressure" in practice is from 100 to 600 kilos, and it is to this that the present paper applies. General Classes and Types. Hydraulic transmission at high pressure usually claims consideration in case the solid mechanism, such as levers, cams, screws, and gear-wheels, would have to be too large, would involve too much friction, or could not be suitably adapted to the speed-requirements of the working-tools. Since steam is mostly the primary carrier of

Jan 1, 1893