Search Documents

By Paul Rhedey

Various commercial pelroleum cokes were heat-1,reated at temperatures between 500° and 1500°C, in a nitrogen atmosphere, in laboratovy induction furnaces. The rate of tenlperature rise was varied betzveen 10" and 300°C per min, or the green cokes were flash-calcined, orv a combination of heating rates was used. Changes in the rate of heating had only negligible effects on the degree of' calcination as characterized by mean crystallite thickness and the chemical properties of the calcined coke. The physical structure of the cake was however significantly affected when rate of heating during calcination exceeded 50°C per min over the temperature range of 600° to 900°C. Surface-accessible porosily increased with the .rate of temperature rise, and this was accompanied by a change in pore size distribution. Source and properties of the green coke also had an influence on the structure of the calcined coke. The evidence presented suggests a similar mechanism of porosity development in petroleuiiz coke during calcination in industvial equiplnenl, such as rotary kilns. An increase in surface accessible povosity incveased the pitch binder requirement when the coke was used as aggregate in Soderberg paste. A correlation was established between calcined coke porosity and paste binder requiremenl. ManY results have been published on the changes of properties of petroleum coke during calcination, such as chemical composition, real density, electrical resistivity, crystallite and pore structure. The correlation of these properties with temperature of calcination and time at maximum temperature has been rather well established in both laboratory and pilot plant experiments. Surprisingly little attention has been given however to the effect of calcination conditions, such as rate of temperature rise or furnace atmosphere, on the chemical and structural properties of the calcined coke. It has been observed that petroleum coke, when calcined in industrial equipment, acquires higher porosity and lower real density than those attainable in laboratory furnaces at apparently identical calcina- tion temperature and soaking time. This paper describes a study of the effect of rate of heating during calcination on calcined coke properties using green petroleum cokes of different volatile matter, hydrogen, and sulfur content. An attempt was made to correlate the changes in coke structure with the flowability of anode paste of the type normally used in aluminum reduction cells. EXPERIMENTAL Petroleum Cokes Used. In the study of release of volatile matter and sulfur during calcination and the effect of rate of heating on calcined coke properties two delayed cokes of different sulfur contents were used. The results of analysis of the green cokes are given in Table I. In the study of the effect of flash calcination thirty-six commercial petroleum cokes from twelve different refineries were used with a range of properties shown in Table 11. Calcination Conditions. Calcination experiments were carried out in a laboratory induction furnace. In each run a 200-g sample of dry green coke sized to 10 by 65 Tyler mesh was calcined in a graphite crucible. The crucible containing the sample was placed in the middle of a stack of eight others filled with metallurgical coke to reduce temperature gradients within the sample. Temperature was measured by two Pt, Pt-10 pct Rh thermocouples and controlled by a Celectray instrument. The two couples generally agreed within 5°C. In the study of volatile matter and sulfur release the samples were heated to temperatures in the range of 500" to 1500°C at a rate of 10°C per min in a nitrogen atmosphere and held at the final temperatures for 30 min. In the study of the effect of heating rate on calcined coke properties the desired rates between 10' and 300°C per min were obtained by manually adjusting the power input. Flash calcination was carried out by dropping 100 g of the green coke into the graphite dish preheated to the calcination temperature. Because of the small heat capacity of the furnace the coke was introduced in 20-g portions at a time. For this purpose a 2-in.-long nipple between two 1-in. gate valves installed on the top flange of the furnace served to provide a gas seal while feeding coke to the furnace. It was estimated that the temperature of the coke reached that of the furnace at a rate of approximately 1000°C per min. Holding time at final temperature was also 30 min. Calcined Coke Proper- Determined. Porosity was determined on 20 by 35 Tyler mesh samples using an Aminco-Winslow mercury pressure porosimeter with an operating range of 1.8 to 3000 psi absolute pressure (100 to 0.05 p pore diameter range).' Apparent density was obtained by the mercury poro-simeter. It represents a particle density of the 20 by

Jan 1, 1968

By H. P. Rassbach, E. R. Saunders

MUCH progress has been made in recent years in the theory and practice of making stainless steel. By effective utilization of oxygen for decar-burization and more suitable alloying agents, it has been possible to attain consistent production of very low-carbon stainless steel. In order to facilitate economical production of stainless steels, the Electro Metallurgical Co. has carried out an extended experimental program that has clarified some of the complex interrelations of temperature and composition under decarburizing and reducing conditions. These results'-:' have been founded in large part on small experimental heats, and in order to confirm their validity and significance under commercial conditions, a survey of stainless steel melting practice has been made with the cooperation of stainless steel producers. Conditions required for decarburization and associated oxidation of chromium, manganese, and iron have been fairly well established in relation to the beneficial effect of the highest practicable temperature. The recovery of chromium and manganese from highly oxidized slags by reduction with silicon has been indicated with somewhat less precision and this study has shown significant deviation in large commercial heats from the small experimental heats. In spite of an unsatisfactory degree of accuracy in estimating the conditions affecting reduction of metallic values, it has been possible to calculate a slag weight in reasonably good agreement with the results observed in large heats. While there still is much to be learned about both the qualitative and quantitative aspects of stainless steel melting, this survey has indicated the manner by which the efficiency of the production process may be measured. Oxidation Period In order to establish practices for the recovery of chromium and manganese from the slag the amounts of these metals oxidized should be known. Moreover, since reduction of oxidized chromium and manganese must necessarily be accompanied by similar reduction of iron, knowledge of the total quantity of metallics oxidized is essential. The relations between carbon, chromium, and temperature under oxidizing conditions were developed by Hilty in 1948.' While it had been realized previously that retention of chromium in the metal during carbon oxidation is favored by high temperatures, the Hilty relation provided quantitative information useful for evaluating melting procedures. For example, it was shown that decarburization to moderate carbon levels can be achieved while retaining substantial amounts of chromium. However, in decarburizing to the low-carbon level necessary for producing 0.03 pct maximum carbon stainless steel, very little chromium remains in the bath at the temperatures generally employed. For this reason, Hilty, Healy, and Crafts' later projected an extension of the chromium-carbon relation to the low-chromium region. Although this chromium-carbon-temperature relation defined the composition of a chromium steel bath at the end of the oxidizing period, it did not provide a direct means for estimating the total amount of metallic oxidation occurring during decarburization of a stainless steel heat. This subject was investigated by Crafts and Rassbach³ and, later, by Hilty, Healy, and Crafts" who demonstrated that metallic oxidation is a function of the chromium content of the initial furnace charge, the minimum carbon content attained, and the temperature. It was further demonstrated from data on 1-ton heats that an empirical relationship exists between the ratio of chromium plus manganese to iron in the slag (S) to the corresponding ratio of these components present in the metal bath. The following expression was derived to permit the calculation of the amount of metallics oxidized during decarburization of a given charge: W-2000 (Cr1 + Mn1)-(Cr2 + Mn2) 1 100s/s+1-(Cr3 + Mn2) where W is the pounds of chromium, manganese, and iron oxidized per ton of charge; Cr1, the percentage of chromium in the charge; Mn1, the percentage of manganese in the charge; Cr2, the percentage of chromium in the bath after oxidation; Mn2, the percentage of manganese in the bath after % Cr + % Mn oxidation; and S =%cr+ % Mn/%Fe in the slag after %Fe oxidation. In order to establish whether the slag ratios of commercial heats are consistent with those found in the experimental heats, the slag and metal analyses shown in Table I were evaluated. These data represent samples taken after the oxidation of two 1-ton and seven 15 to 25-ton heats of types 303, 304, and 304L stainless steel made in chromite, acid, and basic hearths. Fig. 1 illustrates that the results for the commercial heats correlate reasonably well with the relationship originally established for experimental 1-ton heats. It will be noted that in the range of metal composition of these heats, the slag values generally lie above the line. As was suggested by

Jan 1, 1954

By H. V. Welch

In this paper, as prepared for delivery at the Southern California regional meeting on Oct. 14, 1948, it was thought best to interpret the term "economics" in a rather broad manner and to include, in addition to the material losses and recoveries and associated monetary values (Part I), a limited discussion of the increased difficulties or the particular problem and the special requirements, as the particle sizes of the suspended particles range down from the relatively coarse to 100, to 10, to 1 micron or even to a fraction of one micron (Part II). Further, it is not quite in order to overlook entirely the community and individual health problems, although space requires the economics of this to be considered only very incompletely. Therefore, Part III, covering this phase of the subject, is very limited. This paper, then, is divided into 5 parts or headings as follows: I Losses and/or values in suspended solids. II Particle size. III Dust and fumes in community and individual living. IV Means and Procedures for dust and fume collection. V Description or examples of specific equipment in service and of the several types used for dust and fume collection. Because of the wide extent and wealth of subject material available and the space and time limitation imposed, presentation and discussion are less than originally planned. I—Losses and/or Values in Suspended Solids The weight involved in moving streams of industrial plant gases is commonly not appreciated, neither is their carrying power in the weight of solids maintained in suspension and moved with the gas stream from a point of origin or pick-up to a point of dissipation or settlement. These, however, are major weight figures; for example, in a modern iron blast furnace there may be five tons of gas for every ton of iron produced and by the time this blast furnace gas has been burned in stoves or under boilers the weight of gas discharged to atmosphere is on the order of eight times the weight of iron produced. Similarly for nonferrous metallurgy there may readily be from 10 to 20 times the weight of gases discharged to atmosphere as there is metal produced. A cement kiln in operation or a kiln in service to produce metallurgical lime may have on the order of 5 to 6 times the weight of stack gases as of clinker or lime produced, and at least the cement kiln, because of the very fine nature of its feed, is a very heavy dust producer. It may be noted that there have been two developments in progress for nearly three decades. Both are extraordinary in the industrial economics effected and in their ready availability to ever larger units of operation and their ever widening importance in industry, and both are productive of great quantities of finely divided material in furnacing. The first of these is the flotation process for ores, especially the metallics such as copper, lead, and zinc; and the second, powdered fuel combustion for power plant, industrial plants and metallurgical operations. Today, new developments, for example, flotation for the nonmetallics such as higher grade limestone for cement manufacture which requires still finer grinding and the powdered-coal-fired boilers with production ratings of over 1,000,000 lb of steam per hr, bring still more concentrated and hugely increased quantities of stack emission. Perhaps the honors for the greatest interest in the quantities and values escaping in waste furnace and equipment gases belong to the nonferrous metallurgical operations. Their record of achievement in the installation of dust and fume collection equipment, largely baghouses or Cottrell electrical precipitators, is exceeded by no other industry. Something of the magnitude and variety of equipment utilized in such recovery systems was covered by the writer in two papers presented to the Institute some 10 years ago.1,2 It is not intended to repeat the material of those articles, but it is thought that they complement this offering and should be noted. COPPER ROASTERS As the copper roasters are the first of the series of furnaces handling the copper-bearing concentrates in the usual copper smelter of today, it is in order to make them the first consideration. Multiple hearth sulphide roasters, not hard driven, often maintain their dust loss through exit gases at 3 pet or below of feed to furnace; in hard-driven or maximum-driven furnaces, exit gas losses often approximate 7 pet of charge with a ±2 pet variation for special conditions prevailing at some plants. A 5 pet loss of feed in a roaster gas exit, unless reclaimed, often makes the difference between a profit and loss operation, and in many cases substantial recovery is the very basis of dividend payments. As there is available very practical and successful equipment for the collection of the

Jan 1, 1950

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel-making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions.

Jan 12, 1950

By Albert F. J. Bordeaux

(Cleveland Meeting, October, 1912.) THE immediate vicinity of the sea-shore, affording special facility for the exportation of ores, makes it possible to work certain mines in the Vladivostok district, which, in more remote places of Siberia, would remain unproductive. Outside of the city of Vladivostok the population is small and the country is very little prospected. Additional discoveries of valuable deposits like the large body of calamine which has recently been opened in the neighborhood of earlier worked lead-silver ores, in the Tetiuhe valley, are still in the field of possibilities. For many years gold alone was produced, in part from the coastal rivers and in part from a quartz-vein on Askold island near Vladivostok. But the production is diminishing, and prospectors are looking for other rivers in the interior, such as the tributaries of the Ussuri. These rivers are now more accessible than formerly, due to the slow but gradual development, of colonization by the Russian peasants. The few natives of the country, called Orodjones, are of the Chinese race. They resemble the North American Indian and are hardy fur-hunters. They have given some attention to placers and have already shown good specimens of gold-dust from the rivers Iman, Bikin, Noto, etc. Coal-mining was begun in the Vladivostok region more than 20 years ago, but in a somewhat irregular way. The industry is not as yet important and the best coal-seams are badly prospected, or ire even neglected. Copper, lead, and iron exist in several places. The amounts give some encouragement to the anticipation that the discoveries will give rise to important metallurgical works. I here present a review of the various deposits, based upon such safe information as is in hand, when I have not drawn upon my personal observations. Fig. 1 is a snap of Eastern Siberia, showing the mineral deposits.

Oct 1, 1912

By Carl S. Westerberg

1,. C. McCABE*-—An increased derliand for coal in the west is to be expected because of the growth in population and industry during the past ten years. The author calls attention to the increased mechanical cleaning of Utah coal between 1938, when no cleaning was being done, and 194.7, when more than 24 pct of the production was cleaned. This is essentially the Period of most rapid growth of the Pacific Coast. area altliough the growth and, no doubt, the general trends in coal production and cleaning continued at a less accelerated rate during 1948. The Pacific southwest increased 37 pct in population between 1940 and 191.7 while the United States showed only a 7 pct increase in the same period. it has been estimated that there will be an additional 15 pct increase in population between 1947 and 1950. The conclusion that more coal and more mechanicak cleaning capacity will be required appears to be well founded. Mr. Westerberg discusses the cco- nomic advantages of coal cleaning reflected in freight savings, in lower cost per million Btu, and lowered ash and sulphur content. In view of the limited occurrence of coking coals in the west it would be interesting to know whether significant beneficiation in coking strength can be expected from mechanical cleaning of Utah coals. This has been demonstrated for some eastern and midwestern coals. One can readily agree to the desirability of recovering the fine coal that has heretofore been lost in washery slurry. The very cheapness of coal has Iridered

Jan 1, 1950

By N. N. Breyer

A specially built "hard" tensile machine with characteristics permitting the precise detertnination of the drop of the load at the yield point has been used to study the magnitude of the yield-point phenotnenon in prestrained martensitic 4340 steel. A new phenonzenon, the appearance of a secondary yield point, has been observed by holding the specimen at constant strain in the plastic region. Furthermore, it has been found that a series of yield-point drops could be introduced by successive constant strain holds in the plastic region. The isothermal kinetics of the development of the secondary yielding point lave been studied at four temperatures: 24° 0° -18°, and -79°C. From the results of the kinetic investigation, equations for the In a previous investigation1 it was shown that, contrary to generally held opinion, steels of medium carbon content, such as 4340, 4140, and 86B30, in the as-quenched martensitic condition, can be cold-drawn through a die with reductions in area of up to 10 pct without cracking. Tensile specimens of 4340 machined from bars quenched and prestrained in this manner exhibited tensile strengths of about 400,000 psi coupled with 30 pct reductions in area. In addition, it was found that each sample of such steels exhibited a yield point in the quenched, cold-drawn condition. Since these studies were conducted on a commercial hydraulic testing machine of a type which is not well-suited to detailed study of yield-point behavior, it was decided to study this phenomenon more thoroughly on a rigid straining machine. In this new investigation, use of such a "hard" machine not only allowed study of the magnitude of the yield-point drop but also revealed a new phenomenon—secondary yielding of the martensite introduced by stopping crosshead motion after plastic deformation of the sample had begun. The present paper is a report of these findings. MATERIALS AND PROCESSING The material used was a commercial 4340 steel of the composition shown below: 0.41 0.80 0.013 0.019 0.31 0.85 1.76 0.28 1 0.42 0.77 0.015 0.024 0.30 0.84 1.69 0.28 0.08 2 1 = Ladle analysis. 2 = Laboratory analysis. Bars of this steel were processed in the following way: 1) machined to predetermined diameters; 2) austenitized at 870°C for 1 1/2 hr; 3) oil-quenched; 4) cooled to -115°C for 1/2 hr; onset and increase in magnitude of the secondary yielding in this temperature region have been found to fit the relationship ?Ys = Atn where ?Ys is the magnitude of the secondary yield Point in psi, t is the time in seconds, and A and n are parameter characteris-tics of the material. Although the occurrence of the primary and secondary yield points could be rationalized qualitatively on the basis of stress-induced ordering of carbon atoms in the stress fields of dislocations, as postulated in an earlier paper, the kinetics of the secondary-yield-point development were interpreted to indicate that the ordering involves more than just single jumps of carbon atoms from high-energy to neighboring low-energy sites. 5) pickled and lime-coated; 6) drawn through a carbide die. The predetermined diameters were chosen so that drawing through the same die gave the various reductions desired. Tensile specimens of 0.252 in. diam with a 1 1/4 in. gage length were then prepared from the drawn bars and tested. In order to study the stress-strain behavior at the yield point in detail, a rigid tensile machine with a high spring constant was constructed. Columns of large cross section (relative to the specimen cross section) constituted the machine frame. A dc motor was used to drive a screw via a gear reducing train and a "crane" thrust bearing. In this relatively simple device small deformations could be observed un-blurred by the slow response and lower spring constant inherent in hydraulic machines.' A strain-gage dynamometer permitted load changes as small as 8 lb to be read. RESULTS Tensile test samples machined from bars in the as-quenched condition with no subsequent drawing and samples from bars with 3.8 pct reduction after quenching gave stress-strain curves typified by those shown in Figs. I and 2. The time lapse between predrawing and tensile testing varied but usually ranged between 3 to 6 days at room temperature. The strain rate during testing was 0.003 in. per in. per min. The as-quenched curve is seen to have a broad serrated maximum whereas the stress on the specimen prestrained 3.8 pct rose linearly to point A, Fig. 2, fell abruptly to B, and then gradually to C. The abrupt drop to B was accompanied by evidence of incipient necking. The drop of the stress at the yield point in the prestrained samples (A to B in Fig. 2) changed with the percent prestrain, as illustrated on Fig. 3. Although the tensile strength increased continuously with the amount of previous cold drawing, the magnitude of the yield point drop first increased—up to about 6 pct prior reduction—and then decreased. Specimens from bars predrawn more than 8 pct broke in a brittle fashion in the elastic portion of the stress-strain curve.

Jan 1, 1967

By Lars Thomassen, Ernest Kirkendall, Clair Upthegrove

THE amount of research done in the last few years on the subject of diffusion in solid metals is significant of the importance of this problem. To review the literature dealing with diffusion is unnecessary here. Desch1 in 1912 reviewed the work that had been done on diffusion in solids and gave a bibliography of the literature published before that time. Mehl's paper in 19362 is an excellent review of diffusion in metals and contains a large bibliography. Of importance also for its review and bibliography is an article by A. I. Krynitsky.3 While considerable material has appeared in the literature on diffusion in brass, the amount of information is not great compared to that pertaining to some of the other alloys. Most of the information published is of a qualitative nature; that which is quantitative varies considerably. Thus the quantitative determination of the rates of diffusion of copper and zinc in alpha brass by a new method appeared worth while. In the present investigation the rate of diffusion of zinc in approximately the same composition alpha brass has been determined at three temperatures. PROCEDURE The method used consisted of plating copper on a beta brass, heating it to allow diffusion to take place, and measuring the concentration of copper by determining the lattice constant of the alloy. This method is unique in that it uses a beta brass of such a composition that at the temperature at which diffusion takes place the beta brass is saturated with copper. Thus, while the beta brass supplies the zinc, no diffusion takes

Jan 1, 1938

By A. B. Kinzel

Since the exposition of the behavior of certain iron alloys by Sykesl involving the existence of an austenite loop and the discovery of such a loop in the chrome-iron system by Bain,2 there has been much conjecture both on his part and on the part of metallurgists in general as to the exact shape and location of this loop. In previous work commercial steel has been used and the microscope has been employed to locate the critical points so that the position of the loop has been quite approximate. Numerous attempts have been made to measure the critical points of the carbon-free alloys but all of these for one reason or another have failed. A satisfactory method for studying these phenomena is presented here. MateRial The first difficulty in this study was to obtain pure chromium-iron alloys. This has been overcome by melting in a vacuum electrolytic iron and chromium analyzing 99.84 Cr, Fe and C. A pure magnesite crucible was used and the melt allowed to solidify in the crucible. A typical analysis is chromium, 10.10 per cent., carbon, 0.006 per cent., silicon and manganese nil. To overcome the problem presented by segregation, ingots were made into wire 0.04 in. in diameter. This was accomplished by hand-forging the ingots into rods, using an oxyhydrogen flame for heating, in order to avoid carbon. Subsequently the rods were swaged to wire, the heating being carried out in hydrogen. Thus local segregation was eliminated although differences in analysis between portions 50 ft. apart were noted. An electric-resistance method was first tried to determine the critical points, but due to the physical defects in the wire this failed. Bain had previously shown the presence or absence of critical points in a qualitative way by observing the sag in a catenary. The author has devised the following method which gives an accurate determination of the critical points from expansion-temperature curves of suspended wire, a special telescopic dilatometer being used for the purpose.

By Mark C. Malamphy

During colonial times, Brazil was famous for the richness of her alluvial gold deposits. Paul Ferrand has estimated that the gold produced during the period from 1700 to 1820 was the equivalent of some 64 million pounds sterling. Since that time, most of the more prolific alluvial deposits have been exhausted. A few gold mines are still functioning, notably the Morro Velho mine, which is one of the deepest mines in the world. Today, the gold production of Brazil is insignificant when compared with world figures, but there are still many gold-bearing regions and it is probable that in at least some of them profitable returns would result from an exploitation program taking advantage of all the most modern innovations in gold mining and ore treatment on a large scale. In order to demonstrate the value of some of these abandoned prospects and stir up interest in increasing the national gold production, the government has stimulated research. Experimental plants have been and are being established in various places, and tests on large quantities of ores are being carried out on a semicommercial basis. The Geological Survey of the State of Minas Geraes is very active in this line and the Federal Institution is also showing an increased interest in the matter. One of the lesser known gold-bearing regions of Brazil is in the vicinity of Lavras, in the State of Rio Grande do Sul. Gold was first reported from this region in the early part of the nineteenth century. In 1811, D. João VI sent an experienced prospector from Minas Geraes to investigate the validity of the reports. According to the reports of Baron Eschwege, he succeeded in extracting some 30,000 Oitavos (about 105 kg.) during the first few years, but the production costs exceeded the value of the gold obtained.

Jan 1, 1934

By Henry D. Hibbard

A noted ordnance engineer once said to a friend, in speaking of the production of great steel guns, " How is it ? We design our guns with a factor of safety of eight, and the guns burst." The vague way in which internal stresses and strains in iron and steel are often considered and spoken of makes it worth while to examine them, as to their nature, their causes and results, how they may, for useful purposes, be advantageously dealt with, and how, when detrimental or dangerous, they may be reduced or kept within harmless proportions. Rankine defines " strain " as a change of form or dimensions of a solid or liquid mass produced by a stress. This definition seems intended not to cover strains due to internal stresses, and it will help us in the present inquiry to consider strain as a tendency to change as well as an actual change of form. Internal strains in iron and steel are the result of stresses within the mass of the piece, some parts pulling and others pushing in resistance to them; or, in other words, some parts are in tension and some in compression, each part striving to relieve itself from strain and make the piece assume a form in which all parts are at rest. Subdivision, so that each part could relieve its strain by motion relative to the other parts, would, if carried out far enough, practically obliterate strain. The internal strains we are now to consider are not those due to the stresses of the service which the piece is rendering, either alone or as a part of a structure, which may be termed service-strains, but those which originate or at least are contained in the piece itself. Internal stresses in a piece of metal are, like action and reaction, always equal and in opposite directions. The stresses

Jan 1, 1907

By Edward Keller

Under the title, Labor-Saving Appliances in the Works-Laboratory, I published a paper1 in which mas described how multi-manipulations in a works-laboratory and in the furnace-room of an assay-laboratory, can be condensed into single manipulations by applying the proper mechanical devices. For example, I now deposit ill, or withdraw from, a muffle a set of 48 cupels as one unit. The front row (8) of these are blanks or heaters; the other 40, when they have attained the proper temperature in the muffle, are charged simultaneously with the 40 lead-buttons. Three manipulations here accomplish an operation which by the generally customary method requires 136, and this number is only limited by the size of muffle and cnpels. This operation is an enlargement of what I have already described in my former paper, and Fig. 1 shows the improved implements. In the paper referred to I described a gold-silver bead parting-bath, which is the last of the devices used in regular sequence in practice. This bath mas designated as being convenient, but mas not a labor-saver properly. Fig. 2 of the present paper shows a new device. Instead of the original tray, there are now sectional holders for the test-tubes, each having a wooden handle on either end, so that the holders ma?-be removed from the boiling bath, and the acid or water poured oE from each set of tubes (in this case, 7) without waiting to cool. The tubes, held in place by clutches, as shown in Pig. 3, rest in holes in the base-strip, having a smaller diameter than the tubes. Each holder is stamped at either end with a number, so that the bath becomes further useful by permitting several men to use it at the same time without interference. Apart from the handles, the holders are made of sheet-copper.

Jan 1, 1911

By A. Andreas, E.H. Wells

The oil and gas industry of New Mexico recorded notable progress ill 1935. More wells were brought in than in any previous year, and important new discoveries were made. The total number of completions was 340, of which 260 were oil wells, 8 were gas wells and 72 were dry holes. The total oil production was 20,228,947 bbl., an appreciable increase over the 1934 production of 16,636,804 barrels. Many of the wells completed in southeastern New Mexico were acidized. This treatment proved highly effective in increasing the capacity of the wells, the resulting potentials usually being two to ten times as large as before acid treatment. In the Lea County fields in which proration was entirely on an acreage basis, the tendency of many of the operators was to complete their wells according to best conservation practice rather than to obtain the largest possible potential. Much remedial work was done in the Hobbs, Cooper, Jal and Eunice fields, and with excellent results. At many of the wells high gas-oil ratios were greatly reduced and encroaching waters shut off by setting packers. Several companies carried on pretentious geophysical campaigns in the southeastern part of the state. The location of the Amerada discovery well in the Monument field was based on geophysical surveys. The New Mexico Oil Conservation Commission, established by the 1935 Legislature and consisting of the Governor, the Commissioner of Public Lands and the State Geologist, began to function in May. Production in the state thereafter was based on orders issued by the Commission. Proration in the Hobbs field, which had been provided for since July, 1930, by successive proration agreements signed by all operators in the field and approved by the State Geologist, was continued by the Commission by giving approval to the current proration agreement,. A plan of proration for the other Lea County fields that had been in offect since early ill 1934 was adopted. 111 September, 1935, the Commission approved a. proration agreement for the Artesia-Jackson-Maljarnar area in Eddy and Lea counties that had been agreed upon by

Jan 1, 1936

Lieut. Maxwell E. Erdory, now with the Army of Occupation in France, writes as follows: "The 602d Engrs., many of whose officers are members of the Institute, started its active service in France at Avocourt, where we built a road across `No Man's Land.' This road from Avocourt to Montfaucon started us on a career of road building which lasted from Sept. 26 to Nov. 9. The engineer in war has no working hours. Our first job meant 50 hr. continuous work, a layoff of 4 hr. and 18 hr. more. That was our initiation in this war game. "Back in the States we practised building trenches, dugouts, and underground shelters of all sorts. In France we were unfortunate enough to come upon the scene when the so-called open warfare started. That made all the above unnecessary. Roads was the cry and our job was to see that all the artillery got their roads and got over them. "I might mention here that the roads of France, which were in excellent condition except for numerous shell holes, w re one of the leading factors in the rapid termination of the war. "We built a narrow-gage railroad from Romagne to Landre St. George which cost us a few men. At Stenay we did our first bridge building. We built nine bridges across the Meuse, capable of carrying tanks, in 18 hr. The next day the American army crossed these bridges on their way to Virton, Belgium, and the Rhine. " Our course from Virton, Belgium, took us through Longwy, Musson, and Athus, in which towns I inspected the steel plants. In Musson as well as Longwy the Germans had destroyed most of the blast furnaces. This destruction began in August, 1917. In Athus the furnaces were in good condition, the Germans having removed all motors land electrical apparatus, rendering the plant inoperative. I have taken several photos of interest of these plants. "It is but fitting that I say that the engineer in this war has contributed much toward its success but the "Doughboy" is its hero and we engineers one and all say "All hail the Doughboy."

Jan 2, 1919

By Howard S. Bryant

The state of Kansas in 1931 continued to hold fourth place on the list of oil-producing states, despite the fact that low prices for crude oil curtailed drilling to just one-half the amount done in 1930, which itself was the lowest in the preceding 10 years. The estimated crude oil production for 1931, according to sources available to the writer, will approximate 37,037,000 bbl., the lowest since 1925. Thus Kansas produced one-eighth less oil this year than it did last year when it produced 42,729,085 barrels. This year's development was characterized by a very small amount of wildcat drilling; however, large new areas were semiproven for oil production, and several thousands of acres were added to the actually proved areas in western Kansas, so that the state now has larger proven areas of oil reserves than at any time in its history since the heyday of the famous El Dorado pool. The general prospects for oil production in the near future are indeed promising for central western Kansas, where drilling costs are moderate and depths are relatively shallow compared to the remaining unexplored parts of the northern Mid-Continent area. Probably the greatest singular achievement in the state for 1931 was the development of its natural gas reserves. This development took place principally in two spots, McPherson County in central Kansas, and Stevens and Morton counties in southwestern Kansas, and it is a matter of record that more than one and one-half billion cubic feet of open-flow capacity per day were added to reserves, nearly twice the amount developed in 1930, previously the largest amount in the history of gas development in Kansas. Gas pipe lines already built and now building are in position to deliver natural gas by one system to Chicago, Ill., by another to Indianapolis, Ind., from whence lines already lead practically to the Atlantic seaboard, and to other cities large and small located west, northwest, north and northeast of Kansas. Table 2 shows all well completions for 1931 in a form to compare with the results of previous years.

Jan 1, 1932

By Alfred H. Bell

The year 1937 has been outstanding in the history of the Illinois oil industry. During the course of the year the state's daily production has been trebled, increasing from 12,000 bbl. per day at the beginning to 37,000 bbl. per day at the end, and the year's total, 7,426,000 bbl. is 66 per cent above the previous year's production of 4,475,000 bbl. The production in January was 368,000 bbl.; in December it was 1,085,000. Production from the old fields increased slightly. Most of the new production is from fields in the central part of the Illinois Basin, an area that for many years was considered unfavorable to the occurrence of oil and gas. The principal producing horizon of the new fields is the McClosky "sand," an oolitic limestone in the Ste. Genevieve formation of lower Mississippian age. Although development has not yet gone far enough to permit accurate estimates of oil reserves in the new fields, it is believed that they are of the order of 100,000,000 barrels. The following are the oil fields discovered in 1937 listed in order of amount of daily production at the end of the year; Noble (Richland County), Clay City, including Southeast Clay City (Clay and Wayne counties), Patoka (Marion County), New Centralia (Clinton County), Olney (Richland County), Cisne (Wayne County),.Beecher City (Fayette County), and Rinard (Wayne County). One gas field, the Russellville, in Lawrence County, was discovered in 1937. For locations of the new fields see Fig. 1. A generalized geologic column for Illinois, showing producing horizons in the new fields, is given in Fig. 2. The total productive area of the new fields at the end of 1937 was 1712 acres, in which 230 wells were producing. Thisrty-five dry holes were drilled within 1/4 mile of producing wells. At the end of the year there were 19 drilling wells, 28 rigs standing, 18 rigging up and 4 new locations in these fields. In the whole state 447 wells were completed, of which 284 were oil producers and three gas producers. Total initial daily production of

Jan 1, 1938

By G. F. Fix, R. E. Esarey

During 1939, Indiana experienced a grcat increase in prospecting and drilling for oil and gas. Major activity, as during the preceding year, was in the southwestern part of the state, the Indiana portion of the Eastern Interior Coal Basin. An increasing interest was evident during the year, however, in the entire state, chiefly in northern Indiana (on the south flanks of the Michigan Basin) and in the old Trenton field of east central Indiana. In the latter area several tests to deeper horizons in the Trenton and to the underlying St. Peter sandstone were completed. Results in this area have been discouraging, however, since these deeper horizons are very erratic. The regional structure in the Indiana portion of the Michigan Basin is generally favorable to oil accumulation, but the picture is complicated by a uniform mantle of glacial drift and a lack of subsurface information. Several wells were started during the last half of 1939 to test the Devonian and Trenton formations in this area. Production from these formations was found at several localities many years ago, hut, no sustained effort has been made to locate pools in this area, which covers perhaps 20 counties. There were 377 wells completed in Indiana during 1939, and 77 others were in various stages of drilling at the close of the year. Of the 377 completed, 255 were classed as field locations and 122 as wildcats. The field wells were divided as follows: 156 oil wells, 39 gas wells, and 60 dry holes; the wildcats: 98 dry holes, 19 oil wells and 5 gas wells (wildcat oil and gas wells include deeper production in oil fields and field extensions as well as new field discoveries). During the year 218 more wells were completed than during 1938. Outstanding developments for 1939 include the discovery of several new oil and gas fields. In the Griffin field, which was discovered during the closing days of the previous year, 103 wells were drilled, including field extensions. Of these, 97 were productive oil wells. This field now covers more than 2000 acres of productive area and has not as yet been defined. There are five producing horizons in the field, including the Waltersburg, Tar Springs, Elwren, and Aux Vases sandstones of Chester age and the McClosky horizon of the Ste. Genevieve limestone. Produe-

Jan 1, 1940

By G. F. Fix, R. E. Esarey

During 1939, Indiana experienced a grcat increase in prospecting and drilling for oil and gas. Major activity, as during the preceding year, was in the southwestern part of the state, the Indiana portion of the Eastern Interior Coal Basin. An increasing interest was evident during the year, however, in the entire state, chiefly in northern Indiana (on the south flanks of the Michigan Basin) and in the old Trenton field of east central Indiana. In the latter area several tests to deeper horizons in the Trenton and to the underlying St. Peter sandstone were completed. Results in this area have been discouraging, however, since these deeper horizons are very erratic. The regional structure in the Indiana portion of the Michigan Basin is generally favorable to oil accumulation, but the picture is complicated by a uniform mantle of glacial drift and a lack of subsurface information. Several wells were started during the last half of 1939 to test the Devonian and Trenton formations in this area. Production from these formations was found at several localities many years ago, hut, no sustained effort has been made to locate pools in this area, which covers perhaps 20 counties. There were 377 wells completed in Indiana during 1939, and 77 others were in various stages of drilling at the close of the year. Of the 377 completed, 255 were classed as field locations and 122 as wildcats. The field wells were divided as follows: 156 oil wells, 39 gas wells, and 60 dry holes; the wildcats: 98 dry holes, 19 oil wells and 5 gas wells (wildcat oil and gas wells include deeper production in oil fields and field extensions as well as new field discoveries). During the year 218 more wells were completed than during 1938. Outstanding developments for 1939 include the discovery of several new oil and gas fields. In the Griffin field, which was discovered during the closing days of the previous year, 103 wells were drilled, including field extensions. Of these, 97 were productive oil wells. This field now covers more than 2000 acres of productive area and has not as yet been defined. There are five producing horizons in the field, including the Waltersburg, Tar Springs, Elwren, and Aux Vases sandstones of Chester age and the McClosky horizon of the Ste. Genevieve limestone. Produe-

Jan 1, 1940

By Glenn A. Marsh, George Bernard

It is often assumed that aerated oil field brines which are to be injected underground contain dissolved oxygen in amounts which will cause appreciable corrosion. Through the use of a new portable dissolved oxygen meter, accurate determinations were made at three brine conditioning plants. At two older plants, dissolved oxygen concentration in the final treated brine was found to he almost zero In spite of aeration during the conditioning process. At a new plant, dissolved oxygen was initially present but disappeared soon after the brine was "inoculated" with oxygen-free brine from one of the other plants. Corrosion tests at the two older plants have substantiated predictions that the brines would lint be corrosive. These results show that mechanical deaeration may not always be required in brine treating plants. INTRODUCTION The present work was undertaken to add to our knowledge of aeration and deaeration of oil field brines in brine conditioning plants. It is commonly assumed that brines which are exposed to the air soon become more or less saturated with dissolved oxygen. Since oxygen-containing brines are known to be corrosive, precautions are often taken to keep air out of brine through the use of closed systems or mechanical deaeration. The study of oxygen in brine has been seriously hampered in the past because of the lack of a suitable analytical tool. The standard Winkler method for the determination of dis-solved oxygen is satisfactory for use in fresh water, but not in many oil field brines. Corrections have to be made for a number of reducing substances such as ferrous iron and hydrogen sulfide which are commonly present in natural brines. Very often the correction factors are much greater in magnitude than the amounts of oxygen which are to be determined, and consequently erroneous results are obtained. Also. erratic Winkler data are obtained when appreciable concentrations of calcium and magnesium salts are present. The first step in carrying out a systematic study involved designing a portable dissolved oxygen apparatus which would operate in natural brines. Subsequently, this apparatus was used in three brine conditioning plants. Dissolved oxygen data obtained here, and certain corrosion rate data, illustrate the interesting behavior of oxygen in these oil field brines. APPARATUS A portable dissolved oxygen meter described in detail elsewhere,' was developed specifically for use with oil field brines. It is a polarographic apparatus employing a small rotating platinum electrode (cathode) and calomel reference electrode (anode). A potential of 0.7 volts is applied across the electrodes while they are immersed in the brine to be tested. 4References given at end of paper.

Jan 1, 1952

By Charles T. Malcomson

In the United States, improvements in methods of combustion have made possible the use of the smaller sizes of anthracite. This coal is now being reclaimed from the culm banks accumulated by the miners in the more prodigal years. To-day the freshly mined "slush" is segrega,ted and stored against the time when, through briquetting or some other means, it may be utilized as a commercial fuel. For many years Europe has achieved enviable results in the conservation of her small coal by briquetting. This profitable industry, first placed on a commercial basis in France in 1842, has grown to such magnitude that the production during 1913 exceeded 36,000,000 short tons. Briquets produced in Great Britain are used principally for steam purposes and the greater part of the output is either exported or taken by the Admiralty. On the Continent the briquets are sold in all branches of the coal trade. The French railways consume from 16 to 40 per cent. of their fuel in briquet form, and in Germany the lignite briquets (of which 20,000,000 tons were produced in 1913) are as familiar and interesting to the American traveler as the huge porcelain stoves in which they are burned. It is not strange, therefore, that aggressive and far-sighted promoters heralded this means of converting our ubiquitous coal waste into revenue. To the superficial student the briquetting process seemed so simple as to make success easy. It is for this reason principally that the path of the industry in America has been strewn with failures. The rash enthusiast had either not worked out the mechanical problems involved or had failed to grasp the local conditions under which the briquets must be made and sold. It may be confidently stated, however, that in spite of the many vicissitudes through which it has passed, coal briquetting is now an accomplished economic success in this country, and as a profitable adjunct to the coal industry it has come to stay. Several valuable contributions relating to coal briquetting are found in the Transactions. Charles Dorrance, Jr., has sketched briefly the history of the anthracite briquetting plants from the time of Loiseau's pioneer plant down to that of the Lehigh Coal & Navigation Co. at Lans-ford. Since then this phase of the industry has remained practically at

Jan 1, 1915