Search Documents

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By William P. Blake

The metallic element Nickel, discovered by Cronstedt the mineralogist, in the year 1751, as a peculiar metal in kupfer-nickel, remained for a long time comparatively unknown in its true charac-

Jan 1, 1883

By Charles Janin

The first successful bucket-elevator dredge to operate in California was put in comnlisvion wt Oroville in March, 1898. There had been numerous previous attempts at dredging, but noue of the earlier boats proved a success. The gold-miners in California earl3 conceived the idea of a machine to dig gravel from the beds and bars of auriferous streams that were inaccessible by the methods then employed, and it was only a few months after the discovery of gold in California that such a machine was Shipped around Cape Horn from New York to San Francisco. Thij was, however, but the forerunner of many failures in gold-dredging, and was soon at the bottoni of the Sacramento river. During succeeding years many other unsuccessful attempts mere made, and it was not until 1897 that a dredge of the single-lift bucket-elevator type mas floated on the Yuba river. This dredge was built by the Risdon Iron Works for 12. H. Postlethwaite, and would probably have been a success if it had been operated on some of the rich Ororille ground

Jan 1, 1912

By Henry N. Toler

Oil and gas development in Mississippi during 1936 was about the same as during the past three or four years, with less drilling activity in the proven fields; although at the end of the year there was a decided increase in interest and activity. Jackson Gas Field Six wells were drilled in the Jackson gas field, three of which were producers and three dry holes. The gas production for 1936 was 12,968,-000,000 cu. ft., which is 2,500,000,000 cu. ft. more than for any previous year. The total gas production from the field to the end of 1936 has been 58,092,000,000 cubic feet. Thirteen producing gas wells were abandoned during the year because of encroachment of salt water. At present there are 99 producing gas wells in the field. The three oil wells on the edge of the field, which had been producing, were not produccd during 1936, although they are still capable of making some oil with much salt water. The rock pressure at the end of the year was 930 lb., which is a decline of 80 Ib. since the discovery of the field. In March of 1936, the State Legislature appropriated $115,000 to be used by the State Mineral Lease Commission in drilling some gas wells

Jan 1, 1937

By Albert Wright

VEINS of asphalt fill and seal vertical fault fissures at the surface of a large domal structure near Bejucal, Havana Province (about 19 miles south of Havana), so this structure was chosen, by Barnabas Bryan, for the drilling of a well on the theory that oil had risen from below the Cretaceous and had entered the porous sands of the Upper Cretaceous, which outcrop in three places within a radius of 12 miles. The asphalt in these fault fissures, he contended, had sealed them and thereby prevented further dissipation of the oil. Furthermore, he found, in the asphalt, specimens of sand and lime that were indications of its upward migratory character. Ralph Arnold, who discovered the Upper Cretaceous sand saturated with oil in the outcrop near Mariel, in Pinar del Rio Province, has compared the Bejucal structure with the Santa Maria field in California. The surface rock of the structure is Oligocene limestone and shales, thin, bedded and well stratified. This formation has, heretofore, been assigned to the Eocene with a thickness of 3000 ft. and locally called the Nazareno formation. Paleontologic examination of well cuttings, however, has disclosed Oligocene fossils at a depth of 1142 ft. and Upper Cretaceous fossils at a depth of 1541 ft., leaving approximately 400 ft. of very parenthetical Eocene. Whether there is any Eocene in this structure has not been determined.

Jan 3, 1925

By V. H. Wilhelm

In contrast with the previous year's activity, the California oil industry for 1938 showed a decrease in drilling, market demand, and discovery of new oil reserves, although there was an increase in oil production. Although additions to reserves from new fields and extensions were less than withdrawals during the year, reappraisals of discoveries in 1937 added to new discoreries during 1938 amounted to over 300,000,000 bbl. The following comparative statement shows the important changes in various phases of the industry: Throughout the year the storage situation became progressively more acute, owing principally to less Pacific foreign demand, and increased potential from drilling the newly discovered fields and pools (Fig. 1). California storage increased approximately 32,000,000 bbl. during 1938, most of which (approximately 18,000,000 bbl.) was heavy crude and residuum. The market demand for the year was around 600,000 bbl. per day. Because of the trend toward Diesel power for heavy transportation, the non-gasoline-bearing crudes arc fast becoming a drug on the market. New discoveries were instrumental in increasing the potential production of the state from 1,076,000 bbl. per day in January to an all-time high of 1,420,000 bbl. per day at the close of the year; although the indicated reserves of these new discoveries were not equal to the yearly withdrawal of 249,000,000 bbl. As of the end of 1938, the state was voluntarily curtailed about 58 per cent. As a result of prospecting during the year, six new fields were discovered, three fields were extended, and deeper zones were reached in five of the older fields.

Jan 1, 1939

By V. H. Wilhelm

In contrast with the previous year's activity, the California oil industry for 1938 showed a decrease in drilling, market demand, and discovery of new oil reserves, although there was an increase in oil production. Although additions to reserves from new fields and extensions were less than withdrawals during the year, reappraisals of discoveries in 1937 added to new discoreries during 1938 amounted to over 300,000,000 bbl. The following comparative statement shows the important changes in various phases of the industry: Throughout the year the storage situation became progressively more acute, owing principally to less Pacific foreign demand, and increased potential from drilling the newly discovered fields and pools (Fig. 1). California storage increased approximately 32,000,000 bbl. during 1938, most of which (approximately 18,000,000 bbl.) was heavy crude and residuum. The market demand for the year was around 600,000 bbl. per day. Because of the trend toward Diesel power for heavy transportation, the non-gasoline-bearing crudes arc fast becoming a drug on the market. New discoveries were instrumental in increasing the potential production of the state from 1,076,000 bbl. per day in January to an all-time high of 1,420,000 bbl. per day at the close of the year; although the indicated reserves of these new discoveries were not equal to the yearly withdrawal of 249,000,000 bbl. As of the end of 1938, the state was voluntarily curtailed about 58 per cent. As a result of prospecting during the year, six new fields were discovered, three fields were extended, and deeper zones were reached in five of the older fields.

Jan 1, 1939

By R. J. Mechin

TOP-SLICING was introduced in the Pachuca district in 1917 by T. C. Baker, at that time mine superintendent, of the Santa Gertrudis mine. There then existed 1200 ft. (365.7 m.) below the surface, lying between the fourteenth and eighteenth levels (a vertical distance of 108 meters) a block of ore having a length of 295 ft. (90 m.), and an average width of 82 ft. (25 m.) and dipping at an angle of 65°. This block lay in the hanging wall of the vein and consisted of highly altered and fractured andesite, cut through with mineralized quartz stringers. On the foot-wall side, 26 ft. (8 m.) of old filling, left by former operators, was of payable grade. Stoping therein was first undertaken by the square-set filling system, but because of the extremely heavy hanging wall and loose dry filling in the foot wall, all square setting had to be accompanied by spiling, which made the operation exceedingly slow and costly. A system of mining was sought that would eliminate the difficulties inherent to the square-set system in heavy ground and that at the same time would effect the desired economies in mining. After several years, top-slicing has met all the conditions most satisfactorily, so that when similar conditions presented themselves in El Bordo mine, this method was adopted with necessary modifications. El Bordo mine is operated by the Santa Gertrudis company, and is situated about two miles north of Pachuca. Because of the diversity of the orebodies, a number of different mining methods are in use, among them top-slicing.

Jan 10, 1925

By Erminio Ferraris

The development of the mining industry in Sardinia dates from the application of the mining law of 1859, which, following the example of the French mining law of 1810, declared prospecting to be free, and suppressed the liens which had previously attached the mine to surface ownership. The first ore-dressing plants were installed by German engineers upon the classic models of the Harz and of Freiberg; but in 1880 Sardinia commenced to open a new path in that industry, utilizing the refuse from the mining of rich, selected minerals, of poor deposits, and of mixed ores. The first experiments were attempte to adapt the existing apparatus to local conditions, but progress was rapid, as was demonstrated already in 1887 by the calamine-dressing mill of Monte-poni, which exhibited a large plant designed in accordance with the experience gained, and constructed entirely in the machine-shops of the country, after new models and designs.' This example was followed two years later by the Sociékté Malfidano, with a large plant of the same sort, and with the reconstruction of the old-fashioned dressing-mill, built in 1880 by the Austro-Belgian Company. In 1900, almost all the mines of Sardinia had adopted the new designs, and the island contained 32 concen-trating-works, employing 2,000 h.p. and 1,924 workmen. Since that time, there have been added a large dressing-mill for blende at Gennamari, and two for calamine, at San Giovanni and at Masua, while the establishments at other mines have been enlarged and perfected. For the treatment of intimately mixed ores, a large establishment has been built upon the new

Jan 1, 1909

By G. L. Oldright

Nearly all of the present schemes for treating complex (i. e. lead-silver-zinc-copper) ores are based on the idea that lead holds, and will hold for some time, the strongest economic place from the viewpoint of supply and demand of all the non-ferrous metals. Copper, it is thought, will come back to its own when European affairs are stabilized, although at that time competition from Chile, Peru, and Katanga, in particular, will be more severe than in pre-war days. The future for silver and for zinc is uncertain. New uses are developing for zinc, and the market has remained better than many expected, but the stabilization of world markets will bring in foreign competition instead of relief. The cost of producing zinc from simple zinc ores, by the retort process, will, from the nature of the labor required and the increasing cost of fuel, increase steadily. As a result, the small producers of purely zinc ores around Joplin are shutting down their mines, even with a good market price for zinc; on the other hand, the producer of lead from complex ores, in the Rocky Mountain states, is confident of a profit from the sale of his lead, and is seeking means to make the zinc in his ore pay some part of the cost of treatment. However, the tonnage costs for mining and ore dressing are much higher in the Rocky Mountain states, as may be seen by comparing tax-return statements from the various states. Even before the recent drop in the price of silver, many mines were operating on a very slender margin of profit; labor and supplies cost more. Mining at greater depth has shown most orebodies to grow increasingly more complex, so that improvements in mining and ore-dressing practice have not been sufficient to compensate for the additional expense involved in beneficiating these ores. The smelters have bad to meet the same general economic situation, so they can only give

Jan 1, 1924

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By Horace Knerr

The term. "high-yield-strength," used in the title of Dr. Gillett's paper (p. 40) is obviously relative. His discussion is limited to improved steels intended to compete with the low-cost, low-carbon, hot-rolled, sheet and plate steels of commerce made and used on a tonnage basis, without heat-treatment. In his list of about three dozen steels, only three have a yield strength of 70,000 lb. per sq. in., or over. Double such values are not uncommon in aircraft steels. Dr. Jeffries (p. 21) refers to "light-weight metals," obviously meaning strong alloys of low specific gravity; namely, aluminum alloys of the duralumin type and certain magnesium alloys. In a structural material, "lightness" is determined by two factors, strength and specific gravity. They must always be considered jointly. The basis of comparison is a strength-weight ratio, obtained by dividing the desired strength value, such as tensile strength, yield strength, or endurance limit, by weight per unit of volume, such as specific gravity or pounds per cubic inch1. For example, aluminum is a heavy metal, structurally, unless alloyed and heat-treated to give it high strength. When the strength of a structural metal is raised by heat-treatment or by cold-work, its specific gravity is not appreciably changed, but it is made lighter in direct proportion to the increase in strength because less of it will be required to carry the load. The lightness of the finished structure of adequate strength is the real point of interest. This structure must not only carry designed load, but "stand the gaff" of service, which includes the effects of accidental overload, fatigue, corrosion, loosening of joints, and so forth. Neither Dr. Gillett nor Dr. Jeffries mentions the true "lightest material of construction," which is alloy steel, tubular in form (Fig. 1), assembled by welding and heat-treated to a yield strength in excess of 150,000 lb. per sq. inch.

Jan 1, 1936

By C. E. Birchenall

DaVIES and Richardson1 have measured composition changes for Mn1-Owith variation in the equilibrium partial pressure of oxygen at 1500°, 1575°, and 1650°C, where 6 is the deviation from the simple stoichiometric ratio. No trend in this relationship with temperature was observed, so these remarks apply to the whole temperature range. The experimental values and their spread are shown by the bounded straight-line segments in the figure. Davies and Richardson assume that the stoichiometric oxide shows Frenkel disorder, given by the equation Mn2+Mn2+ + Mn" [1] where Mn2+ is a normal lattice ion which moves into an interstitial site (Mni2+) leaving a vacancy (Mn,"). The superscript dashes indicate that there is an excess charge on the anions surrounding the vacancy. Schottky disorder, in which a perfect crystal acquires equal numbers of cation and anion (Ov") vacancies according to leads to equations of exactly the same form in the analysis below. In view of the neutron diffraction results of Roth,2 which shows extensive Frenkel disorder in Fe1-o, Eq. [I] seems more appropriate. The deviations from stoichiometric composition, MnO, result from the addition of oxygen according to In effect Davies and Richardson ignore the variation of Mn3+in constructing equilibrium constants. This approximation might not appear to be very serious if the excess positive charges are really free posi- tive holes (P+) and if the intrinsic conductivity is high as a result of the reaction where e- is a conducting electron. However, the calculations of Buessem and Butler3 indicate that the partition functions of the free charges make a large contribution to the equilibrium constant, and this approximation would not be a desirable one. Furthermore, Morin4 shows that the positive holes are probably localized in MnO and therefore are described better by the mass action principle than by a degenerate gas model. Davies and Richardson's considerations require that activity corrections be applied beyond a 6 value of about 0.005. It is proposed to show here that the dissociation pressure curve can be calculated reasonably well over the whole composition range studied without activity corrections by choosing appropriate equilibrium constants for reactions 1 and 2. As stoichiometric composition The mass action constant, Ks, for reaction [I.] and the equilibrium constant, K,, for reaction [2] are given by where the concentrations which do not change significantly have been absorbed into the constants. The brackets denote concentrations. The deviation from stoichometric composition is given by gardless of [Mni2 ]. Substituting Eq. [7] in [6]

Jan 1, 1961

By E. P. Klier, S. M. Grymko

The transformations in eutectoidal systems have been extensively studied as they occur in steels.&apos; As a consequence of these studies the martensite, bainite and pearlite reactions found for most steels are widely recognized. Further, because of the work of Smith and Lindlief2 and of Greninger and Troiano3 these reactions, except for the bainite reaction, are considered as typical for all eutectoidal systems. The primary alloy studied by Smith and Lindlief2 was a CuAl alloy of near eutectoid composition as was the alloy more recently studied by Mack.4 The transformations in these alloys were, for the most part, studied metallo-graphically, while an X ray analysis of structures was essentially wanting. It has appeared desirable, therefore, to investigate selected CuAl alloys at and slightly away from eutectoid composition. For this purpose three alloys were prepared containing 10.5,11.9 and 13.5 pct A1 respectively. The results of a metallographic and X ray analysis of structures obtained for isothermal transformation of the ß-phase are reported here for the 11.9 and 13.5 pct A1 alloys. Introduction The phase equilibria in the CuAl alloys of immediate concern are indicated in the equilibrium diagram section presented in Fig 1.5 The equilibrium and transition structures which have been reported in this system are as follows: a = copper rich terminal phase (f.c.c.) ß = high temperature eutectoidal phase (b.c.c.) r2 = aluminum-rich intermediate phase (r-brass structure) a&apos; = modified a-phase postulated by Bollenrath and Bungnrdt.26 ß1 = ordered ß (b.c.c.) ß&apos; = martensite structure: A1 < 13 pct (near h.c.p.) ß" = ß&apos; of Smith and Lindlief2 7&apos; = martensite structure: A1 > 13.5 pct (h.c.p.); ß2 of Bollenrath and Bungardt.26 The eutectoid transformation can be suppressed at sufficiently high cooling velocities. The ß-phase is then retained to about 500°C where ordering sets in. The ordering interval is not satisfactorily known but indirectly appears to be non-suppressible. Subsequent to the ordering reaction and consequently at lower temperatures, the ordered ß1 decomposes to a marten-sitic structure. The kinetics of these reactions and in particular those of the martensite reaction have an important bearing on the results obtained in this investigation. Since some confusion exists concerning certain reported aspects of these reactions, they will be considered in some detail. THE MARTENSITE REACTION The martensitic structure is formed on cooling through a critical range6

Jan 1, 1950

By Thomas A. Simpson

THE Birmingham red iron ore district in Jefferson County, north central Alabama, Fig. 1, is bounded on the northwest by the Warrior and Plateau coal fields and on the southeast by the Cahaba and Coosa coal fields. The area of study includes the ridge and valley between Red Mountain and Shades Mountain, Fig. 2, approximately 70 square miles extending from Homewood in the northeast to Greenwood in the southwest. The district is one of the most important producers of hematite in the United States, with an annual production of about 7 million tons. The amount of hematite mined between 1870 and 1950 ranged from 6 to 16 pct of the nation&apos;s total annual production, and the iron and steel products from blast furnaces in the Birmingham district supply the entire southeastern section of the country.

Jan 1, 1955

By K. C. Ko, M. K. McCarter

Experimentation with seismic velocity measurements at Kennecott Copper Corp.&apos;s Bingham mine disclosed that some recognized slide areas are characterized by low velocity profiles. A new traverse technique employed during the investigation allows rapid and precise measurements of a quantity referred to as "apparent velocity." This value is a weighted average of the actual velocity in the overbreak zone near the surface and in the intact rock at depth. The low points on the velocity profile are apparently the result of lower actual velocities and deeper overbreak in less competent material within the slide zones. Experience verifies the usefulness and practicality of the technique in delineating adverse areas prior to detectable failure. The technique may be employed as a rapid and economic means of slope stability surveillance in large open pit mines.

Jan 1, 1973

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

By G. D. Just

INTRODUCTION Large scale underground mining involves the bulk handling of fragmented material. The cost and efficiency of the mining systems is there- fore significantly influenced by material flow characteristics. Flow problems may occur in the form of ore pass blockages which interrupt the free flow at extraction openings. The costs of such delays can be readily assessed and compared to the costs incurred in reducing blockages by improved fragmentation or larger ore passes. In practice the problem is more complex than this statement suggests because it is generally un- economic to design for zero ore blockages. Another major flow problem occurs in the form of relative movement of ore and waste as the fragmented material is extracted. This produces waste dilution in the recovered ore and influences total ore recovery. This flow problem is much more complex than the ore block- age phenomena. Many questions concerning the precise flow characteristics remain unanswered because of the variability of size distributions, particle shapes, material properties and the total extraction layout and design. Model studies can provide a visual and quantitative illustration of probable flow characteristics but full scale data collection is necessary to evaluate the precision of such information. The methods and types of data obtained must be carefully selected to recover the maximum volume of useful information for operational control and future design. It is essential that honest precision levels are assigned to the data and any subsequent analyses. Grade control data may give misleading short term information on flow characteristics because of the difficulty in knowing the true grade of the mass of material before extraction commences. However, in the long term control of extraction grades is vital to the profitable operation of the mining system. The most efficient extraction design and operational schedule can only be determined after all of the facts and variables are known. This is usually only possible after the orebody has been completely extracted. However, if design and operational personnel have a full appreciation of the nature and variability of material flow under different conditions the best possible results should be achieved. The most significant features of material flow are out- lined in this paper in order to provide mine planning and mine management personnel with some of the necessary information relating to material flow. Available facts and reliable figures from selected publications are noted in association with unbiased and hopefully accurate opinions of the relevance of the data to mine design and mine system control. Possible future developments and profitable areas for research into material flow problems are also detailed. MATERIAL FLOW AND MINING METHODS The effects of material flow on the design and operation of an integrated underground ore handling system is one factor which is common to most mining methods. Analysis of the system as detailed by Just, 1980, permits the identification of unit process objectives. For example, a typical underground ore handling system as illustrated in Figure 1, involves the following unit operations:- (i) Gravity flow of ore in stope (ii) Ore extraction at base of stope (iii) Ore haulage on the production level (iv) Dumping of ore into ore pass system (v) Gravity flow of ore in the ore pass (vi) Underground crushing of ore (vii) Haulage of crushed ore to shaft (viii) Hoisting of ore to the surface. Average flow rates in each of these unit operations can be misleading due to variability in incremental capacity caused by flow blockages and machine delays. Thus to effectively analyse the probable performance of the system, it is necessary to have a measure of the flow loading and haulage rate variability. Mechanical equipment performance specifications can be used to provide such information for loading, haulage and crushing; however, in the case of the gravity flow of material field measurements are required to relate the probability of "hang-ups" to the degree of fragmentation. Factors affecting the frequency of flow stoppages are, size, distribution and cohesiveness of broken material and the geometry and size of the flow channel. Ore pass channel design is relatively simple since regular cross-sectional shapes are used

Jan 1, 1981

By C. C. Clark, J. R. Mihalisin, K. G. Carroll

OBSERVATIONS made in this paper were for the purpose of exploring the anomalous behavior of a particular heat of Type 310 stainless steel. The alloy, of nominal composition 25 pct Cr, 20 pct Ni, was observed to form a grain boundary precipitate at exceedingly high rates. A sheet of this metal, 0.060 in. thick, after cooling in air from 2000°F showed the presence of the grain boundary material, whereas none was found after water-quenching from the same temperature. X-ray techniques were applied without success and, in view of the ex-

Jan 1, 1958

By R. W. Raymond

In connection with the discussion of the paper of Mr. James Gayley, presented at the Baltimore meeting, in February, 1892, on " The Preservation of the Hearth and Bosh-walls of the Blast-furnace,"* I offered a translation of a letter received from our distinguished honorary member, Professor P. Ritter von Tunner, concerning the use of carbon-bricks at the Donawitz furnace, then (February, 1892) in the third month of its campaign. The purpose of this brief paper is to put upon record later results of practice with carbon-bricks, both in this country and abroad.

Jan 1, 1897