Search Documents

By A. H. Geisler, J. H. Keeler

Preferred orientations in rolled and annealed titanium sheets were determined by the Geiger counter spectrometer X-ray diffraction technique. Five annealing textures dependent upon the temperature range of annealing were found, and in order of increasing annealing temperature pendent upon the temperature range are: 1—a deformation like texture, 2—a rotated inorder a-recrystallization temperature texture, 3-a retained u-recrysraIlization texture, on annealing at lower temperatures of the ß-region, 4—a transformation texture based on recrystallized a and predicted by the Burgers' relationship, and 5—a ,ß-cube texture. These results are examined in terms of current theories of recrystallization textures. UMEROUS investigators have described the tex- ture obtained by cold rolling the hexagonal metals, titanium, zirconium, and beryllium, which have c/a ratios less than that of ideal packing, 1.633. The basal planes are rotated out of the rolling plane, about the rolling direction, so that the basal poles are tilted toward the transverse direction as shown schematically in Fig. la. In all instances but one,' it was also reported that the [1010] direction was parallel to the rolling direction (see Fig. lb). Hot rolling has been reported as causing a similar tilt of the basal poles in the transverse direction (see Fig. la) and causing the [1010] direction also to be parallel to the rolling direction as shown schematically in Fig. lb. Annealing after deformation does not appreciably change the tilt of the basal poles in the transverse direction." Beryllium2-7 continues to have the [1010] direction in the rolling direction after annealing, and similar observations for titanium and zirconium' . have been reported for annealing at fairly low temperatures, again as in Fig. lb. At higher annealing temperatures, however, the recrystallized grains of titanium" and zirconium have an orientation such that the [1120] direction is approximately in the rolling direction, although the basal poles are still inclined in the transverse direction. Figs. la and lc show the resulting orientations schematically. This change in orientation has been described as a nominally ±30° rotation of the hexagonal crystallites about the basal poles of the cold rolled texture and is apparent from the results which are summarized in Table I for investigations with the X-ray diffraction technique employing film. The angles y, , and ß are indicated in Fig. 2 which represents the stereographic projection of (1070) poles for the mean orientation of a pole figure. Texture determinations for titanium using the Geiger counter spectrometer have provided similar results except that in some instances additional components of the texture were proposed, as shown by the summary of data in the upper half of Table 11. On the other hand, the spectrometer technique, when applied to zirconium,* has revealed a splitting Recently completed studies of the textures of annealed zirconium", show zirconium to possess textures very similar to those reported here for titanium. Therefore, much of this discussion will include zirconium by virtue of its close similarity to titanium in pref erred orientations. of the intense areas of the pole figure for samples annealed at 600°C. This splitting could be described by a 7" rotation of the tilt axis about the normal to the rolling plane. Such a splitting for the annealed texture relative to the cold rolled texture was not observed in other determinations for either zirconium or titanium using the less sensitive film X-ray methoe and makes the relationship between the two types of texture more complex than the simple rotation about the (0001) pole based on film work. The more precise investigations on zirconium permit the descriptions in the lower part of Table 11, which show that the texture depends quantitatively on the temperature of annealing. When zirconium is annealed at temperatures up to 400°C, the texture is similar to the cold rolled texture, while annealing in the range 500" to 900°C produces a texture which is only approximately described as [11%] in the rolling direction. More precisely described results for zirconium show that the two types of splitting ( 1—about an axis in the rolling plane through an angle given in the second column in Table II and 2—about the normal to the rolling plane through an angle given in the third column of Table 11) depend on annealing temperature. The [1120 is the rolling direction only when the annealing temperature is in the vicinity of 900°C

Jan 1, 1957

By Elmer W. Pehrson

THE founding of the American Institute of Mining Engineers in 1871 came at an unusually significant moment in the life of our country. The industrial revolution, in which mineral production played a major role, was just getting underway. The iron industry, established several decades earlier, was reaching sizable proportions. In 1871 pig-iron production was approaching 2 million tons, and the industry had spread as far west as Missouri and Wisconsin. The chief sources of iron ore were Pennsylvania, New Jersey, New York, and Michigan. The age of steel was in its infancy; production had not yet reached 100,000 tons per annum. The gold rush to California two decades earlier and the discovery of other gold and silver bonanzas in the West paved the way for the transcontinental railways, which were then being built and which contributed much to the subsequent development of the great copper, lead, and zinc districts of the Rocky Mountain area. Regular production of copper in the Michigan peninsula and of lead in Missouri and the upper Mississippi region had been established for many years but on a scale dwarfed by the quantities later required as technical progress, invention and enterprise made possible the rapid expansion of industry. Discovery of oil in Pennsylvania in 1859, the growing recognition of the

Jan 1, 1947

By R. A. Vandermeer, P. Gordon

The study of recrystallization in cold-worked metals is complicated by the impossibility of making direct three-dimensional optical measurements. Metallo-graphically, theinternal three-dimensional features of samples must be inferred from their intersections with the two-dimensional plane of polish. The inherent difficulties involved in this procedure have led— particularly during the last few years—to some instances of rather doubtful interpretations of experimental data in terms of nucleation and growth rates in recrystallization. In the present paper an analysis ; is given of the recrystallization characteristics in a polycrystalline alloy containing 0.008 wt pct copper in ZONE-refined aluminum *and an effort is madf to reemphasize the necessity in such studies for attention to the proper statistical relationships between one- two- and three-dimensional features of opaque samples. It is shown that, in common with several recently described cases for other types of transformations,1-5 recrystallization in this alloy can best be rationalized on the basis that all nucleation took place essentially at time zero—i.e., there is no significant time-dependent nucleation during annealing—and that the kinetics are controlled exclusively by the growth-rate parameters. This is true despite the fact that the number of

Jan 1, 1960

By J. M. Gaines, C. H. Herty

It is a matter of frequent record in the literature that manganese will desulfurize molten iron under proper conditions. Particularly has much been written with regard to this action in the mixer, and numerous reports have been published describing experiments in which advantage was taken of this phenomenon in order to obtain a purer iron for the open hearth. The question of sulfur elimination in the ladle has, however, received comparatively little attention. The reaction by which sulfur is removed is considered to be: FeS + Mn = MnS + Fe. The manganese sulfide, being but sparingly soluble in the iron, and of a lower density, will rise from the body of the metal and collect as a slag on the surface. It is therefore an action taking place solely in the metal, and independent of interaction between slag and metal. As will be shown later the presence of slag on the metal tends to offset the effect of manganese elimination. It is this fact which distinguishes desulfuriza-tion in the ladle from desulfurization in the mixer, for it has been shown1 that the amount of sulfur eliminated in the mixer is closely tied up with the composition of the slag. Experimental Procedure In order to ascertain the extent of and the factors controlling this elimination in the ladle, several casts were sampled carefully at the blast furnace and again when the ladles were being emptied, either at the mixer, open hearth, or foundry. If the sulfur content varied from ladle to ladle at the blast furnace the average sulfur content of each ladle was obtained by integrating the curve "sulfur vs. time " for the cast under

Jan 1, 1927

By Cleland N. Conwell

Coals are found in all parts of Alaska, ranging in geologic age from Carboniferous to Tertiary, and grading from lignite through anthracite. Only the Matanuska and Nenana coal fields have been extensively developed. Nenana Field Today roughly 94% of the coal mined in Alaska comes from the Nenana field near Healy. The coal-bearing horizons in the Nenana field are found in a sedimentary sequence of Tertiary age approximately 2800 ft in thickness. The sediments rest directly on schists of possible Precambrian age. Individual coal beds in the field have been designated by both letters and numbers, starting with the alphabetical designations from A to G, and the numbers 1 to 6. Of these coals, the principal beds that are mined are F, 1, 2, and 3. These vary greatly in thickness, e.g., bed 1 ranges to over 50 ft, and beds 2 and 3 to 30-40 ft.

Jan 10, 1972

By C. S. Barrett, A. Smigelskas

There have been no publications of the deformation and recrystallization orientations of the metal beryllium, yet pronounced textures would certainly be anticipated since it is close-packed hexagonal in structure. Having an axial ratio approximately that of magnesium, beryllium probably deforms by nearly the same slip and twinning mechanisms that operate in magnesium, and the textures are likely to be similar or but slightly different from the magnesium textures. In the tests reported below this is found to be the case; the textures are found to differ from those of magnesium only in the details of the scatter from the average orientation. This report covers not only samples rolled at room temperature, but some rolled at elevated temperatures. Since magnesium has been suspected by some investigators of altering its crystallo-graphic deformation mechanism at elevated temperatures, it was considered possible that beryllium might do so and alter its textures accordingly. No pronounced alterations were found, however. Unfortunately, the theory of deformation textures is not in a state of development that permits one to deduce the deformation mechanism from a knowledge of the textures, which means that the similarity of textures at different rolling temperatures, reported here, cannot be taken as definite evidence that the deformation mechanism is actually the same at all temperatures. The general similarity of the deformation textures of magnesium and beryllium also extend to the recrystallization textures of the two metals, judging by the pole figures for recrystallized sheet presented in this report. Samples were prepared in the form of composite sheets made up of small pieces stacked in a pile. Each piece was trimmed with scissors so that an edge was parallel to the rolling direction, dipped in paraffin, and assembled into the pack by aligning it under the cross hair of a microscope. As the desired orientation was obtained on each piece it was secured in place by touching with a hot wire to melt the paraffin. A stack of ten or fifteen pieces was built up in this way, then trimmed to the shape of a T; the portion to be X rayed was then etched to the shape of a wire about 0.045 in. diam with 6N HCl. This method of shaping the sample is a modification of that used by Bakarian on magnesium.' The absorption of the rays in the sample was so slight that it caused no difficulty in interpreting the films. Exposures were made with a 0.030 in. diam pinhole, using molybdenum radiation (40 kv, 25 ma, Type A film at 5 cm, 2 to 3 hr exposures). With the recrystallized specimens it was found necessary to oscillate the specimen so as to reduce the spottiness of the lines. A range of oscillation of 5" was SUB- cient to produce reasonably satisfactory patterns, though the quality was somewhat inferior to that of the deformation texture patterns, and only two degrees of intensity were read from the arcs on the films. Typical photo-grams for each of the deformation textures and the recrystallization texture are assembled in Fig 1. The pole figures were plotted in the usual way with the intensity of the various portions of the diffraction rings estimated by eye. Seven to nine films were made of each sample and each was carefully read in plotting the pole figures. Typical series included exposures with the beam normal to the rolling direction and at 11, 26, 41, 56 and 71" to the cross direction, plus two exposures with the beam normal to the cross direction, and at 11 and 79" respectively to the rolling direction. The rolling was in each case considered sufficient to develop the final texture: the reduction by cold rolling was 84 pct (from 0.0045 to 0.0007 in. thickness), following prior hot rolling in longitudinal and transverse directions and recrystallization; the reduction by hot rolling at 800°C was 90 pct (0.010 to 0.001 in.), following similar prior treatment; the reduction by rolling at 350°C was 88 pct (from 0.005 to 0.0006 in.) after similar prior treatment. The recrystallization texture was determined on a sample rolled at 350" to a reduction of 88 pct (0.0165 to 0.002 in.) after similar prior treatment, then mounted between steel strips to keep it flat and annealed at 700" in an atmosphere of argon. Discussion of Results The results of the X ray determinations are assembled in the pole figures of Fig 2, 3, 4 and 5 for rolling at

Jan 1, 1950

By G. K. Manning, W. E. Few

T has been known for some time that both'inter-granular carbide and intergranular oxide phases cause brittleness in molybdenum. Parke and Ham' indicated that 0.0025 pct 0 present in molybdenum after solidification from the melt was sufficient to induce intergranular brittleness during forging. However, material containing 0.06 pct C could still be forged. However, adding this amount of carbon to insure deoxidation causes the formation of carbides on freezing. These carbides are precipitated at grain boundaries, and Rengstorff and Fischer' have shown they have an unfavorable effect on the room-temperature ductility of molybdenum. Take? in 1928 proposed that the solubility of carbon was a constant value of 0.30 pct from room temperature up to 1800°C. In 1935, Sykes, Van Horn, and Tucker' obtained X-ray data suggesting that the solid solubility of carbon in molybdenum was between 0.07 and 0.09 pct at temperatures from 1500" to 2100°C. The a-solubility line for carbon was included in the Mo-C diagram given in the Metals Handbook as a tentative line based on the data of Sykes, Van Horn, and Tucker. In order to determine the partial phase diagrams for these systems, it was necessary to construct a high-temperature furnace suitable for heat treating molybdenum at temperatures up to 4000°F. A molybdenum resistance furnace was built for this purpose in which samples could be heat treated in a purified atmosphere and quenched from any desired temperature.' Experimental Work Solubility of Carbon: Arc-cast molybdenum supplied by the Climax Molybdenum Co. and 18-gage molybdenum wire samples produced by powder metallurgy at the Fansteel Metallurgical Co. were used in determining the a-solubility line for the MO-C system. The cast molybdenum contained 0.032 pct C initially. Two lots of 18-gage wire were used, one containing 0.011 pct C and the other 0.005 pct C initially. All material contained a carbide phase as received. Fig. 1 illustrates the carbides found in the untreated material. Heat treatment in a purified hydrogen atmosphere was found to reduce the carbon content in the as-cast molybdenum. Purified argonT also decarburized molybdenum samples at temperatures above 3500°F; however, the carbon content remained constant during heat treatment in purified argon at lower tem- peratures. The argon was purified by passing it over titanium at 750 °C and then through a magnesium perchlorate drying tower. The hydrogen was purified by passing it through a commercial hydrogen deoxidizer, followed by a drying tower. Specimens having different initial carbon contents were heat treated in argon at 3500°F for periods ranging from 5 min to 5 hr and were analyzed for carbon. Samples of the same final carbon content had the same microstructures regardless of time at temperature. Furthermore, a gradient between center and surface in the amount of undissolved carbide particles present was never observed. It was concluded that at these low carbon levels, and at the high temperatures involved, diffusion proceeds so rapidly that the specimen is always substantially homogeneous in carbon content, in spite of the gradual loss in carbon. Based on the above findings, the following procedure was used to determine the carbon-solubility limit at 3000°, 3500°, and 4000°F. At each of these temperatures, a number of samples were heat treated, as shown in Table I, and rapidly cooled to room temperature. Since the samples lost carbon in proportion to the length of time heated, a series of samples were obtained of varying carbon contents. By use of a rapid cooling rate, the phases present at the high temperature were retained at room temperature. All samples were examined microscopically. Those found to contain either no excess carbide phase or only a very small amount were then analyzed for carbon. The samples actually analyzed for carbon

Jan 1, 1953

By H. L. Hartman

The estimation of the magnitude of pressure changes which occur in mine ventilation circuits is of primary importance to the mining engineer in making changes in an existing mine or in projecting the ventilation requirements of a new mine. It is a formidable task in many cases, because no adequate theory is available and empirical data are unreliable or even lacking. The common practice of increasing one's estimate of the mine static pressure by an arbitrary "safety factor" to compensate for the unknown is a poor substitute for accuracy. Generally little difficulty is encountered in calculating friction losses in mine airways. As long as the friction factor can be reliably estimated, the well-known Atkinson formula gives accurate results. However, it is in the determination of shock losses that the ventilation engineer encounters difficulty and is apt to resort to an arbitrary allowance. Shock losses may constitute as little as five or as much as twenty-five percent or more of the overall pressure drop in the mine, and such allowances are generally completely unsatisfactory. Since other shock losses have been covered by McElroy (1), this paper deals with a long-neglected source of shock and pressure change in ventilation circuits, divergence and convergence of airflows, here referred to by their more common mining terms, splits and junctions. PREVIOUS WORK There is practically no fundamental information available in ventilation literature on the splitting and junction of airflows, either in mining or mechanical engineering periodicals or handbooks. Fluid mechanics textbooks seemingly avoid the subject of divergence and convergence, except for brief empirical treatment. The only investigation reported for mine ventilation systems was by Weeks, et a1 (21), in 1933. Although applicable to the case of line brattices in coal mines, it cannot be applied to the general case of mine splitting and junctions involving change of direction with little or no area change. In dealing briefly with the subject of shock losses at splits and junctions, McElroy (1) suggests only that they be considered comparable to bends, with losses at junctions being increased 50 pct to allow for interference of merging streams. He recognizes the importance of quantity ratio but concludes that exact quantitative data are lacking to compute losses at splits and junctions. A very capable summary and analysis of the state of knowledge in industrial ventilation and fluid mechanics regarding losses due to divergence has recently been reported by Gilman (3). In considering all earlier work dealing with both air and water as fluids, he compares results on a common basis and obtains good empirical agreement. For divergent flow, the controlling variable in each branch is the quantity ratio, although the deflection angle is of secondary importance. Empirical equations are presented for straight and 90-deg branches with varying velocity ratios, assuming branches smaller than the main duct. These formulas are modifications of the Borda equation for abrupt contraction and expansion. The only information available on shock losses in convergent flow are approximate experimental data presented by Alden (4) and the Manual of Recommended Practice for Industrial Ventilation of the American Conference of Governmental Industrial Hygienists. Alden considers the effects of both quantity ratio and deflection angle. The data indicate an effect opposite to that observed in divergence, the shock loss varying directly with quantity ratio. SHOCK LOSS THEORY Because pressure losses due to shock have been found to bear a constant relation to the mean velocity of flow in a given conduit, they are frequently expressed as a dimensionless function of the velocity head, termed the shock loss factor. For airflow in ducts and mine airways, the shock loss may be represented by the formula (1): Hx - XHv, (1)

Jan 1, 1961

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-B alloys has been measured up to the solubility limit for the formation of boron nitride. The activity coefficient of nitrogen increases with increasing boron content in the range 0 to 7 wt pct B. From experimen -tal data, values have been calculated for the B-N interaction parameter e3 at temperatures in the range 1550" to 1750°C. A value of 0.038 has been estimated for the boron self-interaction parameter eg at 1550°C. The standard free energy of decomposition of boron nitride into the elements dissolved in liquid iron has been determined to be: ?F° = 45,900 -21.25T in the range from 1550° to 1750°C. The nitride is assumed to be of composition BN. BORON nitride has an unusual combination of properties which make it appear attractive in a wide range of engineering applications. Some of its more important and most recent applications are in the nuclear area, particularly in connection with the liquid-metal cooled reactor concept now receiving considerable emphasis. Boron nitride has a high degree of stability at elevated temperatures. It also has excellent ma-chinability and the ease with which its crystals deform suggests applications as a lubricant. These properties stem from a hexagonal layer-type structure similar to the structure of graphite. One of its primary uses to date has been for seals in liquid-metal pumping systems. It is also used in nuclear reactors as an insulating layer to separate two solid metals which are not themselves compatible under the conditions of temperature and atmosphere in which they are used. Its inertness to liquid metals has also suggested use as a mold-release agent in casting processes. In addition to its excellent machinability and reported inertness to liquid metals such as iron, silicon, aluminum, copper, and zinc, boron nitride has high thermal conductivity and excellent thermal shock resistance. This combination of properties would make it appear ideal as a refractory crucible material for refining of high-purity liquid metals, for example high-quality steels. However, since it is known that concentrations of boron as low as 50 ppm can have a marked effect on the physical properties of certain steels,' in particular on the creep and stress-rupture properties, an investigation was undertaken to define accurately the chemical equilibrium among boron, nitrogen, and liquid iron in the range of steelmaking temperatures. EXPERIMENTAL PROCEDURE Two experimental approaches to this problem were employed: a Sieverts' method and a quenching method. In the first method, the Sieverts' technique was used to measure the equilibrium nitrogen solubility in liquid Fe-B alloys of 0 to 7 pct B as a function of nitrogen gas pressure over the melt. The solubility limit of the boron nitride phase formed was determined by the point of departure of the nitrogen absorption from Sieverts' Law. This technique has been applied to liquid Fe-Ti alloys by Rao and parlee,' to liquid Fe-A1 alloys by Evans and Pehlke,3 and to solid Fe-V alloys by Fountain and Chipman.4 In the second method a melt of liquid iron was held in a crucible of boron nitride under a known partial pressure of nitrogen gas. After thermodynamic equilibrium was attained, the melt was quenched in a stream of helium and then analyzed by wet-chemical methods for boron and nitrogen. The Sieverts' apparatus used in the first method was essentially of the same design as the one described by Pehlke and Elliott.5 The charge materials were vacuum-melted high-purity iron (Ferro-vac E) supplied by the Crucible Steel Co. and -325 mesh boron powder supplied by Cooper Metallurgical Associates of Cleveland, Ohio. The boron contained less than 0.02 wt pct O, according to supplier's analysis. Recrystallized alumina crucibles were used to contain the melt. Examination of solidified melts showed these crucibles to be satisfactory with no evidence of any reaction or physical penetration of the crucible wall by the melt. The melt temperature was measured by a disappearing filament-type optical pyrometer sighted vertically downward on the melt surface through a 1/4-in.-diam sight hole in the crucible lid. The pyrometer was calibrated against the melting point of pure iron in the same apparatus, taking the emissivity of

Jan 1, 1964

By C. G. Dunn

IT is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.1 In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth-processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insufficient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered. Until recently observations were that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro- structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1946

By A. R. Denison

Several productive areas in the Mid-Con-tinent are broadly and briefly examined with respect to the present depth of drilling on productive structures, and the thickness of sediments remaining untested. Evidence is offered to show that a vertical mile to two miles of untested but prospective formation remain within reach of the drill. In no case would a well deeper than 15,000 ft. be required, and in most cases to no greater depth than 10,000 ft. Recent outstanding success of deeper prospecting in West Texas demonstrates the merits of deeper drilling on known structure. Introduction New fields discoverd during I942 equaled or exceeded the number in any preceding year. The total amount of oil found by these discoveries was less than in any previous year, for which accurate records are available. This means that the pools now being discovered are much smaller than in past years. This is to be expected, since the prospects available during 1942 were largely those overlooked in the earlier years and therefore represent a second or third order (in quality) of structural feature. This failure to find pools of good size and quality raises grave doubt as to the security of our future oil supply. With military needs rising almost daily, and the period of heaviest con- sumption in our war effort still in the future, there is even a growing doubt as to our ability to supply the amount needed for our ultimate victory. This does not mean that our reserves are inadequate, but rather that our "capacity to produce" may be inadequate. Lacking large fields with flush production, our capacity to produce is rapidly approaching our current needs. ,Since the industry is unable to find the large new fields necessary to keep a safe margin of "capacity to produce," other means are needed. It seems obvious that one of these should be deeper prospecting on the large, proven, productive structural features now known. The exploratory wildcat is drilled primarily in search of a trap and the reason for failure to find oil and gas in nine out of ten cases is due to the absence of a suitable trap under the drill site. Therefore, deeper drilling on a known structural feature that is productive largely eliminates the greatest hazard in wildcat drilling. While by no means all the oil known today is found in structural traps—in fact, some have estimated that less than half is so located— the fact remains that structural traps are far more commonly the oil fields that have multiple horizons of production superimposed one over the other. Outstanding examples are the Eldorado field in Kansas, the Tonkawa and Cushing fields in Oklahoma, the Louden and Salem pools of Illinois, and the richest and most prolific of all structural traps, the Long Beach, Ven-tura and other similar fields of California.

Jan 1, 1944

By A. R. Denison

Several productive areas in the Mid-Con-tinent are broadly and briefly examined with respect to the present depth of drilling on productive structures, and the thickness of sediments remaining untested. Evidence is offered to show that a vertical mile to two miles of untested but prospective formation remain within reach of the drill. In no case would a well deeper than 15,000 ft. be required, and in most cases to no greater depth than 10,000 ft. Recent outstanding success of deeper prospecting in West Texas demonstrates the merits of deeper drilling on known structure. Introduction New fields discoverd during I942 equaled or exceeded the number in any preceding year. The total amount of oil found by these discoveries was less than in any previous year, for which accurate records are available. This means that the pools now being discovered are much smaller than in past years. This is to be expected, since the prospects available during 1942 were largely those overlooked in the earlier years and therefore represent a second or third order (in quality) of structural feature. This failure to find pools of good size and quality raises grave doubt as to the security of our future oil supply. With military needs rising almost daily, and the period of heaviest con- sumption in our war effort still in the future, there is even a growing doubt as to our ability to supply the amount needed for our ultimate victory. This does not mean that our reserves are inadequate, but rather that our "capacity to produce" may be inadequate. Lacking large fields with flush production, our capacity to produce is rapidly approaching our current needs. ,Since the industry is unable to find the large new fields necessary to keep a safe margin of "capacity to produce," other means are needed. It seems obvious that one of these should be deeper prospecting on the large, proven, productive structural features now known. The exploratory wildcat is drilled primarily in search of a trap and the reason for failure to find oil and gas in nine out of ten cases is due to the absence of a suitable trap under the drill site. Therefore, deeper drilling on a known structural feature that is productive largely eliminates the greatest hazard in wildcat drilling. While by no means all the oil known today is found in structural traps—in fact, some have estimated that less than half is so located— the fact remains that structural traps are far more commonly the oil fields that have multiple horizons of production superimposed one over the other. Outstanding examples are the Eldorado field in Kansas, the Tonkawa and Cushing fields in Oklahoma, the Louden and Salem pools of Illinois, and the richest and most prolific of all structural traps, the Long Beach, Ven-tura and other similar fields of California.

Jan 1, 1944

By W. E. Rice

THE ceramic industry has to do with forming or molding articles of clay, and imparting to them their characteristic properties of permanence, strength and color by subjecting them to heat treatment in kilns. This heat treatment is commonly known as "firing" or "burning." The art of firing clay ware antedates the industrial use of coal; hence wood was the fuel first used, and the earliest kilns were built to burn wood. The majority of the clay ware produced today is fired in periodic kilns that are essentially enlarged structures similar to the earliest enclosed kilns; a kiln consists of a large chamber 16 to 32 ft. dia. (or rectangular) in which the ware is charged and fired either in direct contact with flame or hot gases from the fuel, or in saggers which shield the ware from direct contact with the gases. The fuel is burned in a number of small furnaces built in the thick .wall that encloses the chamber; these furnaces are from 16 to 36 in. wide and from 3 to 5 ft. long; some of them have horizontal or sloping grates, but many have no, grates; the last are called "dead-bottom" furnaces. The temperature necessary to mature the charge in the kiln varies for different clays; for some it is as low as 1800°, and for others as high as 2700° F. Wood was an ideal fuel for the low temperatures that were used in early kilns; it burns freely and produces along, clean flame, which promotes uniform distribution of the heat in the kiln; it does not coke and so restrict the passage of air through the fuel bed; the ash does not melt in the fuel bed to form clinker; and the ash that is carried into the chamber and deposited on the charge does not contain iron and sulfur to discolor the clay. The extent of the ceramic industry now precludes the general use of wood in kilns, so that today this industry is one of the large users -of bituminous coal, burning more than eight million tons annually in kilns. Manufacturing plants usually are at or near the source of clay, with deposits of coal suitable for kilns occurring near the clay. The cost of coal is the largest single item of expense in the manufacture of clay ware, and, because all coals are not equally suitable for the process, the careful selection of coal is important. In this selection the desidera-

Jan 1, 1932

By R. A. Vandermeer, Paul Gordon

On the basis of a unified concept, theoretical erPressions for grain boundary migration in recrys-tallization are derzved for impurity-controlled and impurity-independent migration. The expression in the former case is analogous to that Previously derived by Lucke and Detert, and in the latter is shown to be equivalent to that usually obtained on the basis of absolute reaction rate theory. The equations are tested with quantitative experimental data for boundary migration obtained for the recrystallization of poly crystalline zone-refined alumimnz and for binary "alloys" of this aluminum with 0.00021, 0.00043, 0.0017, 0.0034, 0.0068, 0.0124, and 0.0256 at. pct Cu, respectively. All the essential characteristics of the e@erimentally determined boundary migration rates check both qualitatively ard quantitatively with the predictions of the theoretical equations. THE rates of transformations are customarily analyzed phenomenologically in terms of the two component rates—N, the rate of nucleation and, G, the rate of growth of the nuclei. The scientific aim of both theory and experiment is to describe the fundamental atomic phemmena involved in these two component processes with the hope that parameters calculated from theoretical equations will check those found experimentally. In solid state transformations, the theoretical and experimental problems are both generally of almost prohibitive complexity, for in addition to changes in composition and in such properties as density which may accompany transformations in amorphous, nonrigid materials, transformations in crystalline substances also involve structural changes, crystal reorientations, and the development of stresses. In studying such transformations it thus becomes; highly desirable, if not essential, to focus on a transformation and a set of conditions which minimize the number of active variables. This principle has been applied with considerable success by Cohen and his associates' in their evaluation of nucleation theories using the martensite transformation as the basis of study. A similar possibility exists for the evaluation of growth theories by the use of recrystallization after cold-deforming. If an unalloyed metal is employed as the subject of investigation, the recrystallization transformation involves basically only a change in strain-conditions and orientations. In spite of this possible simplilfication, however, until recently little quantitative success has attended attempts to correlate recrystal1ization parameters measured experimentally with those calculated theoretically. It seems highly probable that this lack of success may be attributed, both in the experimental and theoretical treatments, to one or more of the following factors: a) conditions have usually been studied under which apparently* both nucleation and growth are active;

Jan 1, 1962

By C. W. Reith

The development of production in West Texas during the year 1933 was largely confined to the expansion of proven areas, especially Ward County, Iatan and North Winkler. Wildcat activity was at a comparatively low ebb and resulted only in discoveries of probable minor importance in Ector County. The interest shown in deep wildcatting to test beds of pre-Permian age was a new development, which should soon throw light on the possibilities of deeper production from the present producing fields. The important pre-Permian tests of the year were: 1. Stanolind Oil and Gas Co., Todd No. 1, a unitized test, in north central Crockett County on a probable continuation of the Big Lake trend. The well encountered several showings of oil and penetrated an Ordovician section very similar to the productive zones at Big Lake, but was abandoned when sulfur water was encountered at 8041 feet. 2. Gulf Production Co., McElroy No. 103, in the McElroy Field, Upton County. The well was drilling at 8553 ft. at the close of the year in beds of probable pre-Permian age. The test is an important one because it should prove or disprove deep production in the Church-Fields-McElroy pools and also throw geologic light on the deep possibilities of other fields in the western part of the Permian Basin. 3. Humble Oil and Refining Co., White and Baker No. 1, in Pecos County, about 11 miles west of the Yates field. The well is on a nonproductive Permian high and should indicate the deep possibilities of the Yates field. At the end of the year, drilling had progressed to 7200 ft., where beds of pre-Permian age are believed to have been penetrated. The major fields in West Texas, in which present-day proration had its inception, were produced under increased restrictions. A date of importance in the proration history of the area was $ept. 8, 1933, when the Railroad Commission issued an order placing all producing wells under proration. The severe reductions in total outlet made during 1933 were well compensated for by a more than threefold increase in the price of crude oil. Acid treatment was one of the general engineering developments of interest. The work had not progressed sufficie~ltly at the close of 1933

Jan 1, 1934

By M. E. Lombardi

THE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 8 ¼ in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling.

Jan 2, 1915

By B. F. Tillson

There is a dearth of information on the economic threat of silicosis. Even the insurance companies and rating bureaus are in a quandary, and the majority of them avoid any action that will stir up an awakened public consciousness of the serious nature of this industrial hazard. Individual claims for $100,000 are now common in silicosis lawsuits. Because of ('hidden costs," in lowered plant efficiency, the total cost of this disease to industry is probably four times its apparent direct cost. The direct costs vary with the labor policies of the employer and with the labor legislation in force. Direct costs may originate in three ways: (1) voluntary assumption by the employer of medical expenses and loss of earning power of stricken employees; (2) state enforcement of industrial disease compensation acts; and (3) awards or settlements after suits in common law. Examples are offered in the last two classifications. In the Rand, South Africa, compensation laws are in effect and in approximately 20 years prior to 1932 about $65,000,000 has been awarded for silicosis and an additional liability of $34,000,000 incurred, or an average of about t5,000,000 per year. During 1932 silicosis compensation on the Rand was about $6,000,000. No figures are available for the direct capital or operating costs for preventive measures there, nor for the additional "hidden costs." It might be reasonable to assume that silicosis has cost the gold-mining industry of South Africa twenty to twenty-five millions of dollars per year. It is estimated that common-law silicosis claims have, in the last few years, aggregated $50,000,000 in New York State alone and have exceeded $300,000,000 in the United States. Attention is called to the involved nature of the insurance situation for industrial diseases in contrast to accidents. The indeterminant, insidious nature of silicosis makes it particularly difficult to predict necessary insurance premiums and reserves. The serious hazard of this disease was not properly appreciated by either insurance companies or industrialists, so sufficient study has not been given its causation, prevention, detection, treatment, and compensation. Therefore legal difficul-

Jan 1, 1934

By C. D. Woodward

PrioR to 1902, the tramming of ore from the stopes to the shafts, in the Butte mines, was done by man or animal power, but the demand for greater tonnage and the need for more improved methods of tramming the ore resulted in the installation of the compressed-air locomotive in a few mines. Some of the objections to animal haulage were thus eliminated, but this locomotive was not generally adopted, because of a number of limiting features. It was superseded by the electric trolley locomotive. The early types of trolley locomotives were not satisfactory from the operators' viewpoint, but they had many economic advantages and after a number of years, in which improvements were constantly made in the structural details, they became dependable, so that the use of animals for main haulage in the mines has now been practically abandoned. There are now operating in the Butte mines of the Anaconda Copper Mining Co., 185 trolley-type locomotives, each of which has replaced five animals. It cost approximately $50 per month to keep an animal, hence the economies that resulted fully justified the expenditure of electrifying the haulage systems. The haulage conditions in this company's mines possess many advantageous features that arc not always found in underground mine workings. The drifts and crosscuts are large, approximately 5 ft. (1.5 m.) wide by 71/2 ft. (2.3 m.) high, and have curves of no less than 18 ft. (5.5 m.) radius; and the roadbeds of the drifts and crosscuts have a uniform grade of 0.5 per cent. toward the shaft, or in favor of the loaded trips. In all of the mines, except two, the track gage is 18 in. (45.7 cm.): and all tracks in the main haulageways are laid with 25-lb. (11.3 kg.) rails. The stations at the shaft are large, well-lighted, clean, and cool. The average temperature of the stations, however, is about 75" F. (24" C.), while the average temperature in some of the drifts and crosscuts is 92" I?. (33.5" C.). As the orebodies lie at varying distances from the hoisting shafts,

Jan 1, 1923

By C. D. Woodward

PrioR to 1902, the tramming of ore from the stopes to the shafts, in the Butte mines, was done by man or animal power, but the demand for greater tonnage and the need for more improved methods of tramming the ore resulted in the installation of the compressed-air locomotive in a few mines. Some of the objections to animal haulage were thus eliminated, but this locomotive was not generally adopted, because of a number of limiting features. It was superseded by the electric trolley locomotive. The early types of trolley locomotives were not satisfactory from the operators' viewpoint, but they had many economic advantages and after a number of years, in which improvements were constantly made in the structural details, they became dependable, so that the use of animals for main haulage in the mines has now been practically abandoned. There are now operating in the Butte mines of the Anaconda Copper Mining Co., 185 trolley-type locomotives, each of which has replaced five animals. It cost approximately $50 per month to keep an animal, hence the economies that resulted fully justified the expenditure of electrifying the haulage systems. The haulage conditions in this company's mines possess many advantageous features that arc not always found in underground mine workings. The drifts and crosscuts are large, approximately 5 ft. (1.5 m.) wide by 71/2 ft. (2.3 m.) high, and have curves of no less than 18 ft. (5.5 m.) radius; and the roadbeds of the drifts and crosscuts have a uniform grade of 0.5 per cent. toward the shaft, or in favor of the loaded trips. In all of the mines, except two, the track gage is 18 in. (45.7 cm.): and all tracks in the main haulageways are laid with 25-lb. (11.3 kg.) rails. The stations at the shaft are large, well-lighted, clean, and cool. The average temperature of the stations, however, is about 75" F. (24" C.), while the average temperature in some of the drifts and crosscuts is 92" I?. (33.5" C.). As the orebodies lie at varying distances from the hoisting shafts,

Jan 1, 1923

By T. F. Bower, M. C. Flemings

The classical explanation for formation of the fine equiaxed "chill zone " in ingot solidification is that local supercooling near the chill wall causes copious nucleation in this region. This work indicates, however, that convection is an essential element in formation of the chill zone. In the absence of convection, no chill zone forms even though rate of. heat extraction is extremely vapid. Alloy studied was Al-l.5 pct Cu alloy solidified against a copper chill wall. When solidification was initiated at the chill wall in absence of. cor-vection, surface grain size was large (>I cm diam). When it was initiated in the presence of convection, it was fine (<0.05 cm diam). It is concluded that some form of "crystal multiplication" plays an important role in formation of the chill zone. INGOT macrostructures are generally classed as containing one or more of the three zones: "chill zone", "columnar zone", and central "equiaxed zone". These three zones are sketched in Fig. 1; their origin has been discussed in some detail.&apos;-&apos; The classical explanation for formation of the chill zone is that supercooling occurs in the region of liquid metal adjacent the mold wall, and copious nu-cleation then takes place in this region forming numerous small crystals. The columnar region then results by growth of favorably oriented grains (den-drites) which crowd out their less favorably oriented neighbors."5 The mechanism of the columnar-equiaxed transition has been the subject of considerable interest. The generally accepted mechanism, until recently, was that constitutional supercooling developed in front of the growing columnar grains with eventual nucleation of new, equiaxed, grains ahead of the growing solid front.&apos; Recently, it became evident this explanation was not completely satisfactory and it is now evident that "crystal multiplication" plays an important role. This crystal multiplication occurs by separation of dendrite arms from growing dendrites,8?"&apos; and has been shown to be strongly influenced by convection.6, 10-13 Reduced convection results, for a given alloy, in longer columnar zone, larger columnar grains, and larger equiaxed grains.7, 12

Jan 1, 1968