Search Documents

By C. E. Cottrell, G. W. Preckshot, N. D. Delisle, D. L. Katz

Most crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir. mechanisms. Asphalt has been the subject of widespread investigation but, owing to the complexity of the substances being considered, progress has been slow. Investigators working primarily with the asphaltic substances have treated the subject from the colloidal standpoint and have developed theories that picture the asphaltic particles as surrounded by adsorbed materia1s.14,15,17,24 The deasphaltization of lubricating oil by the use of solvents treats the subject primarily from the standpoint of liquid-liquid equilibria.'' A complete understanding of asphaltic substances would make possible the following of the material from its initial state in the crude oil through precipitation processes to the final plastic stage, the most common form of which is used in asphaltic pavements. Since these asphaltic particles are very small, it appears 'hat the electron microscope4 might be a useful tool in studying the precipitation processes. Specimens are examined by the electron microscope in a vacuum and as very thin films, requiring special techniques in preparation of samples. A brief description of the electron microscope and its operation will bring out the difficulties and advantages of its use for this problem. The first work was done with crude oils that had been diluted with solvents for the preparation of the film to be examined. Later a technique was developed by which the undiluted oil film could be made thin enough for direct examination. These two techniques show vastly different results Asphaltic particles have been precipitated from crude oils by a variety of

Jan 1, 1943

By G. W. Preckshot, C. E. Cottrell, D. L. Katz, N. D. Delisle

Most crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir. mechanisms. Asphalt has been the subject of widespread investigation but, owing to the complexity of the substances being considered, progress has been slow. Investigators working primarily with the asphaltic substances have treated the subject from the colloidal standpoint and have developed theories that picture the asphaltic particles as surrounded by adsorbed materia1s.14,15,17,24 The deasphaltization of lubricating oil by the use of solvents treats the subject primarily from the standpoint of liquid-liquid equilibria.'' A complete understanding of asphaltic substances would make possible the following of the material from its initial state in the crude oil through precipitation processes to the final plastic stage, the most common form of which is used in asphaltic pavements. Since these asphaltic particles are very small, it appears 'hat the electron microscope4 might be a useful tool in studying the precipitation processes. Specimens are examined by the electron microscope in a vacuum and as very thin films, requiring special techniques in preparation of samples. A brief description of the electron microscope and its operation will bring out the difficulties and advantages of its use for this problem. The first work was done with crude oils that had been diluted with solvents for the preparation of the film to be examined. Later a technique was developed by which the undiluted oil film could be made thin enough for direct examination. These two techniques show vastly different results Asphaltic particles have been precipitated from crude oils by a variety of

Jan 1, 1943

By H. Rush Spedden, Arvid Thunaes

Pilot plant test work in 1942 and 1943 showed that by a combination of desliming, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants.

Jan 8, 1950

By Charles Catlett

AN examination of the census reports' for 1880, which contain a large number of complete analyses of typical American iron-ores, indicates that the existence of barium sulphate in intimate association with iron-ore is rather unusual. Of 94 analyses reported there, but four show any barium sulphate, and the maximum content amounts to 3.04 per cent. The note of the occurrence of considerable quantities of barite in connection with certain iron-ores found in the Pinar del Rio Province of Cuba may be of interest. These deposits are found near the little village of Francisco, about 25 miles west of the city of Pinar del Rio on the Western Railroad of Havana. The principal ridges are anticlines, and consist of very thick deposits of sandy shales and slates containing a large number of little veins of white quartz which, by the gradual disintegration of the mass of the material, is left covering the surface. This quartz occasionally shows sulphide, but is generally barren of any such indication. At times lenticular masses of a more or less pure limestone were observed in these slates. The shales, which are of light color, are occasionally talcose. The formation would tentatively be classed as the Lower Cambrian, and the heavy ridges of comparatively horizontal limestone found in the anticlinal valleys as the Upper Cambrian. Along the crest of these slaty ridges deposits of iron-ore are found which are apparently in place, and were probably formed by replacement of masses of limestone similar to those noted elsewhere. The ready disintegration of the slates, and the

Jul 1, 1907

By E. R. Gilbert, D. E. Munson

Creep of copper under 75 to 1.50 kg per sq cm stresses at temperatures near the melting point was found to he a complex reaction controlled by three mechanisms acting in parallel. In order of appearance with decreasing temperature, the auerage activation energies, Qc , are 168, 79, and 24 kcal per mole. Stress dependence of the minimum creep rate was found to he an exponential for the two high-Qc processes and a power law for the low-Qc, process. Transition of control occurs from one mechanism to another. The relative transition temperature depends upon the applied stress, and the range oiler which the transition occurs depends upon the difference in the activation energies of the mechanisms. The creep behavior at high temperature is explained by the climb of dislocations through thermally or mechanically formed jogs, CREEP in pure fcc metals at temperatures in excess of one half the absolute melting point is normally controlled by dislocation c1imb.1,2 A climb model which seems applicable, according to an extensive analysis of data,3 was derived by Weert-man.4 This model assumes jog-saturated dislocations and predicts an activation energy, Qc, nearly equal to that for self-diffusion, USd. Although the requirement of jog saturation is restrictive, agreement between theory and experiment seems adequate. Many other theoretical treatments, including an early model by Mott,5 include detailed consideration of jog formation as an initial requirement for climb. These models predict activation energies for creep which differ from those of self-diffusion. Seeger6,7 postulates an observed activation energy related to the stacking-fault energy. Thus, Usd <Qc<5Usd + Uj where Uj is the jog-formation energy. Seeger incorporated qualitatively the influence of the relative numbers of thermal and athermal jogs. Expanding this concept, Shoeck8 explicitly states a function based on formation mode and relative numbers of vacancies: e r ci exp {-uf/k T} exp {-Um/k T} [ 1 ] where Uf and Um are energies of vacancy formation and migration, respectively. The concentration of jogs, Cj, depends upon the manner of jog production. For intersection jogs, Cj is not sensitive E. R. GILBERT, Junior Member AIME, formerly with De- to temperature; for thermal jogs, Cj is proportional to exp {—Uj /k T}. Schoeck regards each mode as a distinct mechanism; therefore, the mechanisms may act together.299 The diversity predicted by theory, surprisingly, has not been substantiated by experimental results. A significant investigation must include the extremes in stacking-fault energy. Extensive creep studies of aluminum10 and nickel,11,12 high stacking-fault energy metals, have been made. Comparable studies on a low stacking-fault energy metal, such as copper, have not. It is the purpose of this paper to report the results of an investigation of the creep of copper under conditions which favor thermal jogs. EXPERIMENTAL Cylindrical compression creep specimens (0.240 in. in diameter by 0.400 in. long) were machined from cold-drawn rods of electrolytic tough-pitch copper containing 0.0007 Mg, 0.002 Fe, 0.001 Ni, 0.0005 Ag, Cd < 0.005, and Pb < 0.005 wt pct impurities. Undetected spectrographically was a nominal 0.04 wt pct 0, which occurs as a Cu2O constituent distributed discontinuously at grain boundaries. Vacuum annealing at 900°C for 15 min produced a stable 0.03-mm average grain diameter. Testing was carried out using apparatus similar to that described by sherby,13 modified by enclosing platens and a push rod in a vacuum cylinder. Normally this arrangement resulted in pressures less than 10 Only a slight surface tarnish, less than 0.0005 in. in thickness, occurred during the test. The applied stress, corrected for atmospheric pressure, was maintained within 2 pct of the desired true stress by the addition of lead shot at fixed strain increments. Creep strain was measured with dial gages as a relative displacement of the upper and lower platens; accuracy of measurement was 0.0001 in. Two creep-test methods were used, the differential or cyclic temperature14 and the isothermal, to obtain creep data at stress levels of 150, 100, and 75 kg per sq cm over the temperature range of 620° to 1032°C. Minimum creep rates were used from both test methods; this was considered proper because comparable temperature tests or cycling to the same temperature gave the same creep rate, within experimental error. The cold vacuum test chamber, with the unstressed specimen in place, was heated to temperature by placing a preheated furnace over the chamber. Temperature equilibrium was attained within 30 min. For the cyclic tests, the stress was removed during the 5 to 10 min necessary to effect the temperature change and re-

Jan 1, 1965

By G. C. Kuczynski

Two particles in mutual contact form a system which is not in thermo-dynamical equilibrium, because its total surface free energy is not a minimum. If such a system is left for a certain period of time, the bonding of the two particles will take place in order to decrease the total surface area, even though the temperature is lower than the melting point. This phenomenon of bonding of two or more particles with the application of heat only and at temperatures below melting point of any component of the system will be called sintering, although the powder metallurgists use this term in a broader sense, including the presence of molten phase and pressure. It is the objective of this paper to study this process and the mechanisms involved in it. This problem is of utmost importance to powder metallurgy and powder ceramics, and its technological aspects have been studied for a good many years. However, the powder metallurgical operations are too complex and include too many superimposing mechanisms, and too many variables for a direct study. It was therefore advisable for the purposes of this study to reduce the variables to a minimum. In this work the radius of the interface formed during bonding in a simple system composed of a spherical particle and a large block of the same metal was studied as a function of time and temperature. It is believed that the mechanism involved in this simple process is fundamental to any sintering operations. Previous Work J. Frenkell was the first to make a serious attempt to develop a theory of sintering. He assumed that the process consists of a slow deformation of crystalline particles under the influence of surface tension which reduces to a viscous flow where the coefficient of viscosity n is related to the self-diffusion coefficient D by the following equation 1 _ D D6kT [1] where 6 is interatomic distance, k the Boltzman constant, and T the absolute temperature. This type of viscous flow of a crystalline substance is essentially different from the ordinary plastic flow. The latter is a specific propcrty of crystals and cannot take place in amorphous bodies. According to Frenkel this viscous type of flow is due to the diffusion of the holes or vacancies arising in the lattice. He was able to derive an equation relating the growth of the interface between two spherical crystalline particles or between a particle and a semi-infinite crystal (Fig 1) to time t at constant temperature. This relationship can be written as follows: x²— 3/2 a/nt [2] where x is the radius of the interface assumed to be circular, a the original radius of the sphere and a surface tension of the material. The other assump- x tions are that x is less than 0.3 and that during the period 1 the original radius, a, of the metallic particle did not change appreciably. A. J. Shaler and J. Wulff2 followed closely the ideas of Frenkel in their theory of sintering of a mass of metallic powder. Neither Frenkel nor Shaler has validated his theoretical speculations with conclusive experimental data. Two measurements reported by

Jan 1, 1950

By Ta M. Li, John D. Wiebmer

Record high prices, burgeoning exploration programs, mine-mill openings, and plant expansions have all characterized a dramatic: resurgence of the US uranium industry in recent years. But while the bull is leading the way on the production side of the nuclear fuel cycle, there is reason for caution from the end-users&apos; viewpoint. How fast will electrical demand grow in the years to come, and what portion of that will nuclear generators supply? How do utilities play their cards when the government holds two of the largest jokers in the deck-a policy on spent fuel reprocessing and a timetable for the fast breeder reactor? Is there a shortfall in domestic uranium supplies on the horizon?

Jan 10, 1978

By W. G. Oldham

By monitoring the capacitance of abrupt p-n junctions it is possible to follow the motion of substitu-tional impurities. A p-n junction is formed by growth of silicon from an Al-Si alloy on an n-type silicon sutstrate at a temperature in the range 650" to 750°C. The diodes are etched and sorted for consistent V-I and capacitance behavior and separated into groups. After irradiation, each set with an unirradiated control set is annealed to various temperatltres for 10 mm and the capacitance remeasnred. For very heavily doped diodes (-1019 per cm3) observable capacitance changes occur at neutron fluences of >1015 per cm 3. The results may be interpreted in seceral ways, the simplest of which is to assume simple vacancy diffiision with small impurity -racancy interaction (at the diffiision, i.e. annealing temperature of 700°C). In this interpretation it is found that a typical vacancy makes about 1024 jumps and travels about 10-5 cm before disappearing. The required effective annihilation center density is about 1016per cm3 . Estimates of the vacancy-impurity interaction can be made and the above numbers correctecl, but for arty reasonable assumptions the number of vacancy sinks connot be much reduced. ThE complete annealing of radiation induced defects requires that the vacancies and interstitials either recombine, travel to the surface of the crystal, or travel to an annihilation center, e.g., a dislocation or a precipitate. If the interstitial is ignored except as a possible vacancy annihilation center at low temperatures,* the motion of vacancies may be followed by monitoring the corresponding motion of substitutional impurities. pfister2 has measured the enhanced diffusion of impurities in an asymmetric shallow diffused silicon structure by optically monitoring the junction movement. In these experiments we monitor instead the capacitance of a heavily-doped deep symmetric p-n junction. The sensitivity for this method is several orders of magnitude higher than in Pfister&apos;s technique, mainly for two reasons: 1) the junction capacitance of a heavily-doped junction is sensitive to impurity movements in the Angstrom range* com- and 2) the junction may be far from the surface which is a major annihilation center for vacancies. THE EXPERIMENT A p-n junction is formed by the epitaxial growth of silicon from an A1-Si alloy on a silicon substrate at a temperature in the range 650° to 750°C. The technique used is the transport of an aluminum melt through a temperature gradient.4 A 10-mil thick aluminum disc is sandwiched between two silicon wafers and the assembly raised to about 650° C with a temperature gradient normal to the sandwich. After about 8 hr the upper (hotter) wafer has been entirely transported and deposited epitaxially on the substrate wafer. The substrate and overgrowth resistivity are measured with a 4-point probe. The as-grown structure is lapped until the wafer is about 1/2 mm thick with the junction in the center. Contacts consisting of electroless nickel covered by electroplated rhodium are applied to both the p and n sides. The wafer is diced into square dice 1/2 to 1 mm on a side and the dice are etched sufficiently to remove approximately 1 mil of silicon. The following results are all for aluminum (p-side) and antimony (n-side) doped specimens with NA =3x 1018 per cm3, ND = 2-8 x 101A per cm3. The diodes are sorted for consistent V-I and capacitance behavior and separated into groups. After irradiation, each set with an unirradiated control set is annealed and the capacitance remeasured. A special capacitance measurement method is used to insure a low sensitivity to shunt resistance. The diode is voltage driven and the current monitored by a phase lock amplifier. It is possible to adjust the detector phase to a point where shunt resistances as low as 100 O have no effect on the reading. The diodes in this study have a capacitance in the range 1000 to 5000 picofarads and a shunt resistance in the range 100 to l06 O depending on the stage of the anneal. THEORY The theoretical problem is twofold: 1) The computation of the amount of impurity diffusion and hence the impurity profile resulting from a given amount of vacancy motion, and 2) the computation of the capacitance from the impurity profile. A comparison of the theoretical and experimental capacitance (in particular the changes) yields the amount of vacancy motion. Vacancy Motion. A convenient parameter to measure the total amount of vacancy motion is Jv the total number of vacancy jumps per unit volume. Although this parameter varies with position in the crystal, owing to vacancy annihilation at the surfaces, it is approximately independent of position far from the surfaces, i.e. in the junction region. In terms of the number of vacancies per unit volume Nv and the vacancy diffusivity given by

Jan 1, 1970

By M. W. Strong

The technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in formation, the type of problems, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differential pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all materials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improvement of material and its most efficient use has to be carried out. In this paper will be discussed the main mud problems of Iran, some of which are peculiar to local conditions while others are of the general type common to all workers in this subject. Underground Conditions In deep wells in Iran the normal overburden may consist of: (1) up to several thousand feet of marls with interbedded sandstones and limestones of varying porosity and permeability; (2) beneath this a chemical series of rock salt and anhydrites, containing various marls and thin limestones,

Jan 1, 1939

By S. R. Goodman, Hsun Hu

PREVIOUS investigations on the temperature dependence of rolling texture transition in high-purity silver1&apos;2 and in electrolytic copperS have shown that a brass-type texture is favored at low rolling tem- peratures, whereas a copper-type texture is favored at high rolling temperatures. The transition takes place gradually as a function of the temperature of deformation, and a general correlation between texture transition and stacking-fault frequency or probability exists—a copper-type texture is associated with low stacking-fault frequencies, and a brass-type texture is associated with high stacking-fault frequencies. If the stacking-fault energy is calculated from the stacking-fault frequency and the dislocation density of the specimen, one finds that with low stacking-fault energies a brass-type texture will be developed, and that with high stacking-fault energies the texture will be of the copper-type. These findings are consistent with the idea that the formation of rolling textures in fcc metals may depend on their stacking-fault energy, although results of such nature always involve the ambiguity that a change in the density (or width) of stacking faults produced by deformation at different temperatures may be actually due to a variation in the stress, rather than due to a change in the specific stacking-fault energy per se. It has also been shown that the type of annealing texture depends entirely on the deformation texture. From a copper-type rolling texture, a strong cube texture will be formed upon recrystallization, whereas from a brass-type rolling texture, the annealing texture will be quite different from the cube orientation. Based on these results on texture transition in pure fcc metals, it appeared possible to effect a

Jan 1, 1963

By M. W. Strong

The technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in formation, the type of problems, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differential pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all materials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improvement of material and its most efficient use has to be carried out. In this paper will be discussed the main mud problems of Iran, some of which are peculiar to local conditions while others are of the general type common to all workers in this subject. Underground Conditions In deep wells in Iran the normal overburden may consist of: (1) up to several thousand feet of marls with interbedded sandstones and limestones of varying porosity and permeability; (2) beneath this a chemical series of rock salt and anhydrites, containing various marls and thin limestones,

Jan 1, 1939

By Edmund Newton

THE steel industry of the United States has depended in the past almost wholly upon imports for its supplies of manganese. Many of the important domestic sources yield ores leaner in their natural condition than the foreign ores the steel industry has been accustomed to use. To make them available, therefore, either&apos; the ores must be concentrated or the practice of the steel industry modified. Roughly 25,000 T. annually of high-grade manganese ores are used for dry batteries, for chemical purposes, and in other ways; while approximately 750,000 T. are required for making steel. By present practice, every ton of steel takes an average of about 14 lb. (1.8 kg.) of metallic manganese. This is generally added to the steel in the form of an alloy, the standard alloys being the 80-per cent. ferro-manganese and the 20-per cent. spiegeleisen. During the year 1917 286,000 T. of ferromanganese and 193,291 T. of spiegeleisen were made in this country, the former largely from imported ores; and 45,381 T.

Jan 2, 1919

By C. W. Nicolson

THE Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less.

Jan 1, 1938

By Marvin Lee

Kansas continued holding, for its seventh year, the fourth position in the list of oil-producing states. The crude-oil production, according to purchaser&apos;s reports to the State Corporation Commission, was 40,008,940 bbl.; as assembled by the Oil and Gas Journal, 41,305,768, and by the U. S. Bureau of Mines, 41,942,000 barrels. Increase of production from 1932 was largely due to greater stability of the industry, and increased return of demand for Kansas oil, caused by the addition of Federal assistance in national production regulation which reduced illegal production, of some areas out of Kansas, that had been destructively competing with Kansas crude or its refined products, at less than cost of production. Prices continued to advance from the lowest level of 25c per barrel during part of May and June, until by the end of September 36" gravity crude had reached $1 per barrel and continued at this price the remainder of the year. Price stability, for a period greater than in previous years, has brought renewed confidence to those producing oil and has led to renewed interest and increased purchases of Kansas leases. Drilling was confined chiefly to the number of wells necessary to protect from offset and other drainage in the field and to meet the requirements of expiring lease contract deeper areas in Mid-Continent, are an added inducement to exploration. The renewal of interest in the search for new fields in Kansas is already apparent and 1934 will probably see more wildcatting than for several years. This is due both to the expiration of leases on large blocks and to actual demand of the industry for new fields. Exploration for favorable areas is being actively conducted by the various methods of surface, subsurface and core drilling and geophysical work. Much of western Kansas cannot be mapped by surface study and geophysical exploration has been of considerable assistance and has led to a large use of the seismograph. Several companies are conducting seismograph surveys and leasing on findings already secured. Development under the more favorable conditions of 1933 can be readily seen by the comparison of the following reports for the last weeks of December in the respective years.

Jan 1, 1934

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments, and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table 1 are reported the compositions of the core and cladding alloy for the material used for the experiments. [ ] In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion.1-7 Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R301 varies with the gauge, as shown in Table 2, several gauges were investigated. [ ] MATERIAL AND PROCEDURE The material used was sheet of the following gauges: 0.025, 0.040, 0.064, 0.102, 0.170. Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: 910°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After 200 min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1945

By David E. Hyatt, Christopher H. Cox, Franklin T. Davis

INTRODUCTION The composition of water used in the flotation process has always been of primary interest to the flotation metallurgist. It is by alteration of the chemistry of the water introduced to the process that flotation separation is effected. In only a few cases has it been necessary to treat available water prior to use in the process. In the past, flotation tailings were treated for the removal of solids via the tailings dam and water decanted from the dam was either recirculated to the process or discharged to the surface water system. The choice of recirculation or discharge was based upon water availability, effect of recycle water on the process, and economic considerations. The Federal Water Pollution Control Act Amendments of 1972 have charged the United States Environmental Protection Agency with establishing effluent limitations from point sources of discharge into the navigable water of the United States. A detailed study, sponsored by EPA, of the water of ore processing plants took place in 1974 and 1975 and guidelines for these plants will presumably have been published by the time this paper has been presented(1). The action of many of the individual states preceded the EPA in this attempt to regulate the quality of the water discharged from industrial point sources. Even with recycle of tailings water, some water is discharged from tailings dams into the substrata and at least one state is currently preparing guidelines for the quality of water discharged into the substrata.

Jan 1, 1976

By C. H. Jr. Herty

IRON oxide .(Fe0) plays an extremely important part in the manufacture of steel. In the open-hearth furnace and the Bessemer converter it is the chemically predominant compound and controls to a large extent both the operation of the furnaces and the composition and quality of their products. Almost all of the refining action is carried out through the medium of FeO, which oxidizes carbon, manganese, silicon, and phosphorus. At the end of any open-hearth or Bessemer heat the steel contains dissolved iron oxide, which must be wholly or partly eliminated. The type of deoxidation product depends on the amount of dissolved iron oxide and on the deoxidizer used. After the heat has been deoxidized and while it is being teemed, iron oxide diffuses from the ladle slag into the metal, causing losses of deoxidizer and increase in iron oxide content of the steel. It is generally believed that non-metallic inclusions are responsible for a great many failures of steel in service and for decreased yield of steel during rolling. The basis of most non-metallic inclusions is dissolved iron oxide. This investigation was undertaken in order to determine the amount of iron oxide that will dissolve in iron under various conditions. Steel-making slags are complex and it has been thought best to determine solubility under simple slags as a first step. The study is being continued under slags whose compositions approach those of operating. slags.

Jan 1, 1928

By J. P. Hirth, C. S. Hartley

A simple graphical technique is presented for rapidly determining the ratio of resolved shear stress on slip systems in single crystals to the applied stress (Schmid factor) for various simple states of stress. Master plots are presented which, when used in conjunction with an appropriate stereo-graphic projection, allow one to determine the Schmid factor for all slip systems in a crystal of given orientation. It is shown that one such plot suffices for simple tension or compression, flex-ural bending, and biaxial compression, while a combination of two different plots must be used for torsion and simple shear. STUDIES of the deformation behavior of single crystals are most valuable when the applied stresses are resolved onto the various slip systems of the crystal. A careful study of the available slip systems and proper selection of the state of stress used and the specimen orientation can then yield quantitative information about the probability of specific dislocation reactions, the strength of barriers to plastic flow, and the mechanisms of yielding and flow in general. It is the purpose of this work to analyze some common states of stress used in deformation studies and to present a simplified way of determining for these cases the ratio of the resolved shear stress on the slip systems to the applied stress (Schmid factor). I) CALCULATIONS We first define two orthogonal coordinate systems: one based on the specimen geometry (a right circular cylinder of radius, R, is considered here) and one based on the particular slip system of interest. The unit vectors and angles specifying the two coordinate systems and the relationship between them are listed in Table I. The relationships among the various angles and unit vectors are shown on a stereographic projection in Fig. 1. The transformation matrix between the (XI X2 X3) and (x&apos;1 x&apos;2 x&apos;3) system is x1 x2 x3 X&apos;1 a11 al2 a13 x&apos;2 a21 a22 a23 x&apos;9 a31 a32 a33 where in this case the direction cosines aij are given by a11 a12 a13 aij = a21 a22 a23 a31 a32 a33 sin 0 cos F cos 0 sin F cos 9 = -cos 0 cos F sin 0 sin F sin 6 [1] 0 -sin F cos (p In terms of Eq. [I.], the stresses sij, referred to the slip system, are determined from oij, referred to the specimen axes, by1,2

Jan 1, 1965

By John Cogan

Field observations were made of rock phenomena in shale, dolomite, and fractured quartzite in the Burgin Mine, Eureka, Utah. Draft closure rates were measured with extensometers and convergence gages. In addition the effects of hydraulic props upon the retardation of closure was also monitored. Drift closure rates were found to be constant and to vary between 0.32 x 10-8 min-1 for dolomite and 23.8 x 10-8 min-1 for soft shale. The installation of props set at constant load served to retard the closure rates. General results show closure to occur at a constant rate for all cases, to be non-uniform around the drift openings, and to be increasingly retarded toward a zero rate by increases in prop load.

Jan 1, 1979

By M. Tsunekawa, T. Takamori, T. Hirajima

In spherical agglomeration in water, the pattern of the growth behaviour of agglomerates is essentially determined by the surface chemical properties of the particles and the oil-water interface. When particles are suitably hydrophobic and oil-water interfacial tension is not too low under an adequate condition for agglomeration, large agglomerates are formed in the initial stage and micro- agglomerates do not appear. When particles are poorly wetted by oil and the interfacial tension is low, initially micro-agglomerates are formed and, after certain aging time, they grow to large agglomerates in a relatively short time without formation of intermediate size agglomerates. Under adequate conditions, the amount of oil and power input do not produce any remarkable effect on the pattern of growth.

Jan 1, 1980