Search Documents

By E. A. Stevens

In a low and gently sloping ridge extending some 1500 ft. southward from Squaw Mt., and now.covered by the buildings, or crossed by the railroads and streets, of a portion of the city of Victor, there is an ancient volcanic vent or crater, which exhibits one of the most interesting phenomena of the great upheaval and volcanic disturbance that built up the hills of the famous Cripple Creek gold-field—of the period when mass was piled on mass to form the mountains and foothills; when fissures and craters opened, and lavas, welling up, overflowed the surface, until, finally cooling, they effectually choked their vents, thus forming many of the ridges that stand out in bold relief, and the dikes that seam the Continent. This particular occurrence, though limited in dimensions, shows in miniature certain stages of the eruptions of Etna and Vesuvius,* Kilauea and Loa; and illustrates what was (with the exception of the penetrating dikes) the closing chapter of the early volcanoes whose emanations have contributed to the

Jan 1, 1901

By Moshe Sheinkin, Douglas E. Julin

Large tonnage operations face many problems in adequately planning ahead for future years production. In order to maintain desired levels of production, such problems as source of tonnage, man- power and equipment requirements, tailings disposal and water requirements must be anticipated. Of course, before any of these problems can be analyzed, daily tonnage requirements and its source must be determined. Looking ahead for one year or even two or three is usually not sufficient time to adequately prepare an area for production. Because of the sequence of mining and the multilevel nature of the 42,000 tpd Climax mine in Colorado long-range planning must be on a ten-year basis. By using a ten-year base, adequate time is allowed to gain access and prepare a new level for production. Usually eight years will be required for this phase of the initial mine preparation. Once production has been started on a level and access to the area is available, three years is usually sufficient to prepare a new block for production as long as it follows in the normal sequence of mining.

Jan 4, 1967

By Frank C. Roe

Two cogent and ubiquitous facts have supported a constant search by the ore processing industry for better wear resistant materials in equipment. First, designs and types of equipment change or improve continually to meet the economic and physical demands of different and/or leaner ores. Second, practically all equipment is subject to impact and abrasion conditions that probably are more severe and extensive than in any other industry. Development and testing by operators and equipment manufacturers alike, has produced an extensive variety of longer lasting metal alloys, rubber, plastics, ceramics and other materials to improve equipment performance under different specific conditions. The need for diversified materials becomes obvious upon the simple realization that no two beneficiation operations are identical. Among the variables in the handling of ore are: 1. Size and weight of ore particles. 2. Hardness and sharpness of ore particles. 3. Concentration of ore particles in liquid or gas suspension. 4. Velocity and direction of particle impact toward equipment surface. 5. Coefficient of friction between ore particles and equipment surface. 6. Temperature of operation. 7. Chemical environment of operation.

Jan 12, 1967

By Joseph Jensen

MANY fields have been zoned by nature with shales and intermediate waters between oil zones. Limitations thus imposed have been the basis on which the field was developed. In contrast thereto, in the Ventura Avenue Field, nature proved more generous. Always expecting to find such similar limitations, operators drilled deeper and deeper into the oil zone without finding any distinctive shale bodies other that the Gosnell shale and only one intermediate water, which became the point below which the final water shut-off of each well was made. Thus, on top of the structure, about 3300 ft. of oil-bearing zone has been penetrated below this intermediate w9ter-a distance of 4000 ft. below the Gosnell shale. At first it seemed that the greater the penetration in the zone, the better the well. The error of this assumption became evident

Jan 1, 1930

By J. A. Holmes

Venezuela has continued during 1929 to demonstrate that it is destined for many years to come to be one of our most important sources of crude petroleum. The producing fields of the Bolivar Coastal district along the east side of Lake Maracaibo have continued their phenomenal production, and two new fields have reached the near producing stage, while the results of deep test wells have strengthened the predictions and expectations that oil will be found and produced from many other pools and from several different geological formations. The finding of these new oil pools is not going to be easy, because the surface evidences of geological structure are scanty, and the subsurface problems are difficult, but intelligent effort backed by ample resources may be counted upon to overcome these obstacles and lead to a continued increase in the number of producing fields in Venezuela. During 1929 the total production of Venezuela was approximately 135,953,000 bbl., an increase of nearly 30,000,000 bbl., or 28 per cent., as compared with the preceding year. During 1929 oil in steel storage in Venezuela decreased from 13,000,000 to about 11,000,000 barrels. Tables 1, 2 and 3 briefly summarize Venezuelan production by fields and by years, and show the trend of production since its establishment on a commercial basis. Table 1.---Production of Crude Oil in Venezuela by Years, 1917 to 1929 All Figures in Barrels of 42 Gallons Total PRodUction Total PRoduction Year VeneZUela, Bbl. Year Venezuela, Bbl. 1917....................... 227,000 1927.................... 63,181,000 1918....................... 368,000 1928.................... 106,000,000 1919....................... 258,000 1929.................... 135,953,000* 1920..................... 548,000 Grand Total Since Ineep- 1921...................... 1,544,000 tion................... 380,791,000 1922....................... 2,448,000 Increase, 1929 over 1928.. . 29,953,000 1923..................... 4,170,000 Per cent. Increase......... 28.2 1924....................... 9,234,000 Per cent. 1929 Production 1925....................... 20,219,000 of Total............... 35.7 1926....................... 36,641,000 * Includes estimate for closing period of 1929.

Jan 1, 1930

By Lester C. Uren

It is realized that the depth of fluid maintained in a pumping well is sometimes influenced by other considerations than the quantity of fluid that will enter the well: the prevention of sand incursion, prevention of waste of natural gas, and the maintenance of a suitable submergence for the pump, for example. These latter factors have an important influence on the productivity of the well, so that otherwise unwarranted fluid levels must sometimes be maintained to offset them; but where the handling of unconsolidated sands is not a problem of consequence and where water has been properly excluded, the principles developed here and the practices recommended should apply. The principal objective of the producer should be to produce the maximum quantity of oil in the shortest possible time. Any method or equipment that will increase the rate of production during the early years of the life of the well, when gas pressure is high, will greatly augment the ultimate production. The maintenance of a proper fluid level in the well at all times will go far toward accomplishing this desired result. For a given set of conditions surrounding the flow of oil into a particular well, in which the viscosity of the oil, the porosity and grain size of the sand, and the diameter of the well appear as constants, two variables determine the quantity of oil that will flow from the sand into the well. These are: the effective pressure behind or within the oil in the reservoir sand, and the fluid level maintained within the well. The former is the expulsive force that causes movement of oil from the sand into the well, while the latter determines the magnitude of a resisting force opposing such movement. The first of these factors is largely beyond the control of the oil producer, but it is in his interest to reduce the opposing force to the lowest economic limit.

Jan 1, 1925

By J. G. Thompson

THE methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value represent-ing the sum of the oxygen contents of several or all of the oxide con-stituents present. With such diversity in the principles and. aims of the different groups, it is not surprising that concordance of results by differ-ent methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the vari-ous methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metal-lurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1936

By P. C. Keith

IT is difficult to talk about atomic energy and the engineer without repeating a number of phrases that have been worn smooth with use Mr John M. Hancock has spoken to you of the two-sidedness of atomic energy, one useful, and the other destructive. If a control plan of the type that he has outlined is adopted it will be perfectly possible to go ahead with the peacetime development of atomic energy Failing the adoption of such a plan, emphasis will of necessity be placed upon the perfection of atomic energy as a weapon of destruction I want to speak, however, in the hope that atomic energy will be developed for peace-time use, and speak about the role of the engineer Before I can do that I must, outline the framework within which the engineer must work, and then I would like to go back and tell of some of the things that he has done, in the hope that that may throw some light on what he may be expected to do in the future Last year the McMahon Committee the Senate Committee charged with drafting domestic atomic-energy legislation-held extensive hearings in an effort to strike a balance between the negative attitude of what to do about atomic energy and the positive attitude of what to do with it Out of these hearings grew the United States Atomic Energy Act, calling for a civilian commission to exercise control over all atomic-energy activities in this country As you

Jan 1, 1947

By SME

A regular feature of the December issue is the abstracts of graduate theses in the mineral industry field presented during the preceding year. The following abstracts were submitted for this second article in the series.

Jan 1, 1976

A regular feature of the December issue is to be abstracts of graduate theses in the mineral industry field presented during that year. The following abstracts were submitted for this first article in the series.

Jan 1, 1975

By Alvin L. Langstaff, Harold D. Raymond

The design of entry systems and mining panels in room-and-pillar oil shale mines seeks to optimize extraction while ensuring both short- and long-term stability of mine openings. Important criteria for optimization include the definition of allowable roof spans and minimum pillar dimensions. Factors considered pertinent to the design of roof spans and pillars are discussed in this paper. They include, but are not limited to, physical properties and grade of the oil shale, depth of burial, presence and frequency of partings and joints and adverse effects of blasting. Also discussed briefly are some of the ventilation and production considerations in mine design.

Jan 1, 1984

By T. M. Yegulalp

This article summarizes some of the results of the continuing research activity at the Henry Krumb Schools of Mines, Columbia University, directed towards a better understanding of the stochastic behavior of slurry flows in underground coal-slurry pipeline systems. Fundamental ideas supported by field observations are presented and a Semi-Markov model of the slurry flows is developed. As a result of this formulation, behavior of combined slurry flows from N independent coal faces can be expressed in analytical form. The contents of a slurry surge tank receiving slurry flows with certain stochastic characteristics is investigated in a function of discharge pump characteristics and time.

Jan 1, 1983

By Charles J. Haas

The resistance which rock bolts offer to shear movements along fracture planes and bedding planes near a mine opening has been suggested as one of the mechanisms by which bolts contribute to the support of weak rock in the roof or sidewall. That such displacements do occur is a fact fairly well known. Inspections of drill holes that have been drilled for some time often reveal that the holes have been offset at one or more points some time after drilling. Resin grouted bolts are often cited as being better able to resist shear movement in the roof because the annulus around the steel bar is filled with grout, whereas the sides of a conventional bolt will not contact the rock until a rather large shear displacement has occurred. When this project began, there were no experimental data to support or refute the above arguments. A laboratory shear test program was, therefore, devised to evaluate the effectiveness of various types of bolts in resisting shear under various conditions which exist in situ. Research reported earlier (Haas, 1976) included a theoretical analysis of a conventional bolt intersecting a shear surface, and experimental data on the shear resistance of smooth (lapped) shear surfaces, intersected at various angles by conventional and resin grouted bolts. The present paper extends the previous analysis to consider the effect of the initial roughness of the shear surface. Joint roughness is a particularly significant factor since undulations of the shear surface cause dilatation of the joint, which in turn, causes high tensile loading of a bolt intersecting the joint.

Jan 1, 1982

By Harold H. Haman

In view of Twentieth Century advances in mineral dressing technology, most modern metallurgists would be inclined to class jigging as an early, somewhat primitive, representation of their art. The practice of metallic sulfide concentration by jigging is becoming rare. This is so, in part, because the type of ore amenable to the process is becoming rare. It is appropriate, however, that this symposium recognize that a significant contribution of domestic zinc remains dependent upon coarse preconcentration by jigging, and that the state of the art be described even though the theory and applications are already well delineated in technical literature. One of the few areas still using jigging as a major concentrating process is The Upper Mississippi Valley. AREA HISTORY AND JIGGING The Upper Mississippi Valley (UMV) has produced one billion dollars worth of zinc and lead at current prices. The district includes the southwest part of Wisconsin, the northwest corner of Illinois and an adjoining narrow strip of Iowa. Within a total area of 4,000 square miles, important sub-districts cover about 400 square miles. As is widely known, early mining in this district involved shallow lead---crevice deposits of galena that were very selectively mined, hand sorted and cleaned, and then smelted at or near the site. The district has produced almost a million short tons of metallic lead, a very large part of this during the fifty- year period following 1830. Zinc mining began at the end of the civil war, but at a very low rate until about 1905.

Jan 1, 1970

By AIME AIME

OUT of the fabulous iron ranges of Michigan?s Upper Peninsula since Pearl Harbor have come go to the steel mills to become tanks, guns, ships, and other weapons for a United Nations' victory. But the contributions to the war effort, as far as Michigan's iron country is concerned, do not stop there. The same men who mine iron ore deep inside the earth also are "mining" on top of the ground, gleaning a harvest of scrap iron and steel that is writing a big chapter in the War Production Board's salvage program. At virtually every mine over an area of a hundred square miles, everyone from the top mine official and straw boss to the man in the dippings is scrap conscious. They know the importance of the ore they mine but they are equally familiar with the importance of iron and steel scrap in war production. The successful job they are doing in salvage is a tribute to the entire Upper Michigan mining industry and to the man who marshaled them into action-John M. Bush, chief of the land department for the Cleveland- Cliffs Iron Co. at Negaunee, and for ten years an A.I.M.E. member. Also, this job should be an inspiration to 611 mining. metallurgical, and petroleum communities as to the latent possibilities of organized scrap recovery.

Jan 1, 1943

By C. G. Brehm

THE anthracite-producing region is in the northeastern section of Pennsylvania, and has an area of approximately 484 square miles. It is divided geographically into three separate fields, known as the Northern, Middle and Southern. The Northern field, with Wilkes-Barre approximately at its center, is a basin about 60 miles long and almost 6 miles wide at its greatest distance across. Generally speaking, it may be said that the coal meas-ures in this field lie horizontally, or on slight pitches, and consist of from 11 to 19 veins of coal, varying in thickness from several inches to several feet. The intervening strata between veins may be composed of slate, clay, rock or shale, or a combination of several, and are sometimes very thin. This condition often causes a treacherous roof, therefore roof sup-port and the attending hazard of mining are problems of concern. The Middle field is made up of a number of small basins of not very great depth, and the measures, which are in like number to those of the Northern field, are varying inclinations running from nearly flat to steep pitches.

Jan 1, 1938

By J. M. Avasthi

The DOE-funded (Contract No. DE-ACO3-77ET13108) Gulf Research & Development Co. (GR&DC) field tests of underground coal gasification in steeply dipping beds (UCG/SDB) were conducted in the North Knobs area, located 12.8 km (8 miles) west of Rawlins, WY. The site has a gently rolling, sparsely vegetated, semidesert terrain on the transition zone between a broad, flat basin (Great Divide Basin) to the west and the subdued mountains of the Rawlins uplift to the east. A comprehensive geotechnical program (Ahner et al., 1980) was essential to successfully complete the test program. Emphasis of the program was the subsurface characterization of the site and consisted of mapping, drilling and logging, core analyses, and hydrologic tests. The samples of lithologic units over- and underlying the G coal seam were tested in the laboratory for their modulus and strength. This program provided the required data necessary for designing surface facilities, input for permits, and ensuring correct placement of the process modules. The two UCG tests at the Rawlins site were conducted in the nominally 6.7 m (22 ft) thick G coal seam (rank-subbituminous B), dipping at 63°.

Jan 1, 1984

By Carle Hayward

IN reheating quenched steel to remove part of the hardness, the softening effect has generally been considered to be a function of temperature and time. The temperature effect is well known, and long before pyrometers were heard of the blacksmith was able to do a good job of tempering, by rule-of-thumb methods and experience in judging temperatures. Modern conditions, which demand steel that will withstand the severest tests, require that the heat treatment he carried out with every possible precaution to secure the best results obtainable. Pyrometers and heat-treatment furnaces of many types are on the market and improvements are continually being made so that it is now possible to regulate the temperature in heat treatment very accurately. There is -still a question regarding the time that the steel should be subjected to treatment. It is customary with all operators to insure the desired tem-pressure throughout the specimen and it is generally supposed that a longer treatment of a hardened steel produces a further softening but there are few published figures showing the exact effect of time of treat-ment at constant temperature. A search of the literature disclosed several brief statements that the tempering effect was a function of both time and temperature, but in no case were any figures given. The opinion is very generally held that the well-known tempering colors are accurate indicators of the degree of tempering. This is disputed by Brearley (The Heat Treatment of Tool Steel, page 102) who states: It has been said that the result would be the same in respect to both hardness and other properties whether the colors were obtained by a shorter heating at a higher temperature or a longer heating at a lower one. This, to say the least, is a very doubtful conclusion, and is certainly not borne out by mechanical tests on oil-hardened and tempered motor car steels, which, after tempering for periods varying from 15 min to 2 hr., show no very great differences. The present investigation had for its object the obtaining of some definite data regarding the effect of time, which might serve as a guide to those engaged in the heat treatment of steel. The Rhode Island Tool Co. cooperated by furnishing the steel and machining the test specimens.

Jan 2, 1917

By John Birkinbine

An unusually large number of crystals of magnetite obtained in the exploitation of a deposit of magnetic iron-ore of remarkable purity, encouraged the preparation of this paper, and its presentation at this time, that the matter might go on record in the Transactions. To make this record more complete, a preliminary statement is offered concerning the district and locality in which the ore is found. To the northeastern portion of the State of New York the United States is indebted for a large percentage of the iron-ore which has assisted in developing the resources and industries of the nation. As early as 1804, iron-ore was mined between Lake Champlain and the Adirondack mountains, and this district has since been an important and continuous contributor to our iron-ore supply. The production of the Lake Champlain district for the last, eleven years is as follows: Years. Gross tons. 1879,...........420,341 1880,...........531,000 1881,...........637,000 1882,...........675,000 1883,...........500,000 1884,...........504,894 1885,...........379,077 1886,...........588,752 1887,...........768,852 1888,...........789,419 1889,...........750,230 Approximate total,.....6,644,565

Jan 1, 1890

By B. P. Canning

In recent years much attention has been given to comminution theory and the design of crushing and grinding installations in large plants. The day of the small plant is not over, however, and we will attempt to analyze some cost aspects of conventional plant design, particular to their smallness. Small plants generally have the same design requirements as large plants, however, certain additional restraints are imposed which generally reduce efficiency and availability. The engineer must take particular note of these restraints in order to properly design crushing and grinding installations for these plants. Whatever equipment is selected for small plant crushing and grinding circuits, it is more costly on a per-ton capacity basis than for a large plant. Circuit Design Small crushing and grinding circuits of recent design usually are of one-line concept utilizing simplified flowsheets. This is the logical outcome of a cost evaluation excluding special considerations and is the basis of the circuit design discussion and cost evaluation which follows. Objections to the one-line concept have been voiced with arguments claiming little flexibility, low availability, higher disaster risk, etc., however, experience has proven these arguments not to be convincing. Equipment of sufficient capacity is available on the market for all normal applications up to the 4000 mtpd plant size here considered and the engineer has complete freedom of choice. Where separate treatment of ores is required, the single-line plant concept requires adequate ore storage be provided with facilities for clean-out between campaigns on one or the other ores. It is very difficult to justify parallel crushing and grinding sections for small plants as material handling is more difficult with small flows involved, and equipment costs become significantly higher. Cost Evaluation Criteria In order to evaluate the small plant comminution circuit on a cost-effectiveness basis, a test model is here established for a comparison basis. Although it is recognized that the parameters chosen will fit only certain metal mining applications, the cost trends should provide useful information for other applications. The test model used is a one-line comminution circuit which considers maximum space utilization in an all-enclosed plant. Plant feed is assumed to be 90 percent passing 12 in. with nominal maximum rock size

Jan 1, 1982