Search Documents

By R. Hogg

Sintering is a process in which the pore structure of an agglomerated powder is modified. For many applications, it is desirable to be able to control the pore structure in order to optimize such properties as mechanical strength and reactivity (availability and accessibility of solid surfaces to reactant gases, for example). In general, these properties will be determined by the total porosity and the pore size distribution of the agglomerate. In the work described in this paper, a physically realistic mathematical model for the sintering process has been developed. The model is based on the usual assumption that the pore system in an agglomerate can be treated as a network of interconnecting, cylindrical pores of continuously varying size. It is further assumed that the total pore length is conserved during the course of the sintering process. Using standard expressions for the rate of shrinkage of an individual pore, the model can be used to predict the changes in total porosity and pore size distribution as sintering proceeds. Experimental pore size distributions, obtained by mercury intrusion porosimetry, for the sintering of oxides appear to be in general agreement with the predictions of the model.

Jan 1, 1977

By M. C. Van Camp, J. D. Miller

Preliminary results are reported regarding the design and development of a pilot scale air sparged hydrocyclone for cleaning fine coal 590 pm (- 28 mesh) containing 24% ash and 1.6% sulfur. The principle of separation is the flotation of hydrophobic coal particles in the centnjugal field generated by the fluid flow in the air sparged hydrocyclone as discussed in another publication. This 152-mm (6-in.) hydrocyclone has a nominal capacity of 0.9 t/h (1 tph) and experimental results suggest that separations vastly superior to a water-only cyclone are possible. In addition the separation efficiency is as good, if not better, than that achieved with conventional flotation cells. For example, typical results indicate that 75% clean coal can be recovered at 15% ash leaving a tailing product of almost 50% ash. These experimental results coupled with the high capacity of the air sparged hydrocyclone (imagine a retention time for flotation of only two seconds compared to two minutes for conventional flotation) may represent a significant breakthrough, not only in coal preparation technology, but in the flotation of fine particles in general.

Jan 1, 1983

By Alexander Bowie

In many places throughout the Western mountain plateau regions of the United States coal beds in place have been burned over very extensive areas, the fire evidently originating on the nakedly exposed outcrop of the coal bed and gradually burning its way into the bed for considerable distances under very heavy cover. The surface evidences of the burned-out coal beds are seen in the calcined and discolored rocks overlying the places of the outcrops. The greater the mass of the burned coal the higher the results of its combustion can be seen in the overlying strata. I have noted many instances of this condition in the States of South Dakota, Wyoming, Colorado, New Mexipo, and Arizona. In the lignite fields of Dakota and Wyoming I noted stretches of level country many square miles in extent where the surface rooks were roasted and vitrified by the burning of a great bed of lignite lying nearly level and with a light cover; this is probably the most favorable natural condition for the burning out of a coal bed. The less the depth of the rock covering overlying the coal bed, the better the chance for a continuous supply of air to the fire; but when the coal bed dips heavily into the ground, or even if level, if it passes under a hill or mountain which gives the bed a heavy covering of strata, the fire has more chances of being extinguished from natural causes than in the first condition described. The distance which a crop fire may extend into a coal field is very much influenced by the dip, the thickness of the coal bed, and the nature of the rock covering immediately overlying it. In reasoning on this subject, it would seem logical to assume in the case of a coal-bed cropping at the base of a hill and dipping into it, with an extensive drainage surface above the crop line, that a crop fire would be promptly extinguished by the caving in of the overlying strata and the precipitation of the rainfall from the drainage surface above the outcrop through the breaks formed in the caving strata. This consideration would be more or less effective according to the climate of the location and the nature of the overlying strata. In a humid climate where the rainfall was heavy the water from the natural precipitation alone would probably extinguish a crop fire before it could work its way very far under cover, but in an arid climate this preventive does not seem to be effective.

Jan 1, 1915

By Thomas Egleston

The ores of mercury of North California are composed of metallic mercury and cinnabar. They are found in serpentine, and are very often associated with chalcedony, in masses more or less irregular, often concentrated enough, however, to furnish ores yielding from three to ten per cent., and sometimes richer. This deposit makes its appearance in Vallejo where it has been worked. North of here the mines are more developed. Most of the quicksilver mines, however, are situated in Sonoma and Napa Counties. On its outcrop the serpentine rocks have become decomposed, and have often been washed away to a considerable depth, so that in many cases in their neighborhood, what is apparently nothing but ordinary dirt, will frequently contain from two to three per cent. of metallic mercury, with but a trace of cinnabar, in which case, as at the Sonoma mine, it is made up into adobes and distilled. Such material does not require to be mixed with dirt to be made into adobes. Very often, also, the outcrop of the rock, where it is not decomposed, is filled with metallic mercury, so that by striking a pick into it, as at the Rattlesnake mine, a pound or more of mercury at a time will sometimes spurt out. Such rock as this is found in several localities in every stage of impregnation, and usually makes very rich ore. There is generally, however, very little of it, and it is found only in the first workings; the ore in depth is always cinnabar. At the Rattlesnake mine near Pine Flat, where large quantities of metallic mercury are found, the rock contains so much petroleum that it has been necessary to make special arrangements to burn the carbides of hydrogen, since the distillation of the petroleum causes an extra quantity of poor soot to be formed in the condensation-chambers. At the Geysers the ore is associated with large quantities of sulphur and gypsum, so that in a hand specimen there is often more sulphur than cinnabar, which is a serious impediment to working, especially for the modern style of furnace with iron condensers, and causes so much soot to be formed that it has been known to penetrate as far as the blower, and to so completely clog it as to prevent its revolution. The ore coming from the mine is more or less hand-picked. In one or two cases attempts have been made to treat the poorest, and especially the very fine ores, mechanically as at the California works.

By M. J. Bradley, P. H. Dike

THE art of melting nonferrous metals, in smelting, casting, and in compounding of alloys, is highly dependent on a knowledge of the temperature of the metal. This knowledge may reside in the experience and judgment of the melter, or it may be based on measurement by suitable instruments. It-is our purpose to discuss briefly the instruments available for such measurements, and more at length the present, practice in molten metals, without recommendation. In the limits of time and space allotted, we can do little more than mention the available methods of measurement that are directly applicable in this field. In the 1939 edition of the Metals Handbook, issued by the American Society for Metals, pages 285-310, there is a more extensive discussion of pyrometry than can be attempted here, which should be referred to for details we must omit. For reasons that will appear, thermoelectric pyrometry will constitute the major portion of our discussion of the subject, only limited attention being given to radiation or optical pyrometry. METHODS OF MEASUREMENT THERMOELECTRIC PYROMETRY A thermocouple consists of two dissimilar wires, or a wire inside a tube of a dissimilar material, joined together at one end, which is placed in the region or medium where the temperature is to be measured, while the other ends are connected through suitable lead wires to a voltage-measuring device, which may be a millivoltmeter or a potentiometer. An electromotive force is generated in the circuit, which is proportional to the difference in temperature between the hot junction and the junctions of the lead wires to the measuring instrument. If this latter temperature is maintained constant, the e.m.f. measured varies only with the temperature of the hot junction. Every thermoelectric pyrometer is calibrated for a particular cold-junction temperature such as 0°F., 32°F. or 75°F., but usually it is more practical to compensate instrumentally over the probable range of cold-junction temperatures than to maintain the junction at the particular temperature for which the instrument was calibrated. Thermocouple Materials Only a very few pairs of metals are in frequent use for pyrometric measurements. The most generally used are iron-constantan for temperatures up to 1500°F. in oxidizing and up to 1800°F. in reducing atmospheres and chromel-alumel, which may be used in oxidizing atmospheres at temperatures up to 2400°F. for intermittent service. The accuracy of the latter deteriorates rapidly at temperatures above 2200°F. Platinum vs. platinum-rhodium thermocouples may be used up to a temperature of 3000°F , but they are easily contaminated by slow absorption of

Jan 1, 1946

By Arthur S. Dwight

We author of this historical chapter will perhaps be criticized for limiting his subject to the history of the blast furnace in lead smelting, and especially to the part it played in the great custom ore-smelting business which for three decades or more was the means of opening up vast mineral treasures and practically dominated the mining industry in the Rocky Mountain region of the United States, in Mexico and in Canada. The men of that era shared the romance and the thrills of mining, and bore their part as pioneers in the building of the great West. The present writer was too young to participate in the first of the three decades mentioned, but immediately thereafter came under the apprenticeship of some of the men who had worked out the early metallurgical problems of the industry, became personally acquainted with most of the others of that group, heard the tales of early experiences, successes and failures, the gossip of the frontier and mining camps, from all of which there remain embedded in his mind clear impressions of the outstanding personalities of that time. That is the background against which the fifty years of intimate contact with the mining and smelting business and his own experiences as metallurgist stand out in his memory, and it is hoped that the gentle reader may understand and approve his desire to rescue from comparative oblivion the fundamentally valuable results accomplished by these fathers of the industry. It will be the purpose of this chapter first to narrate the general history of the growth of the industry; second, to pay tribute to some of the pioneer metallurgists, and third, to discuss some of the salient points of the metallurgical practice at different periods, to illustrate the technical progress of the art. The series of eight Annual Reports of Rossiter W. Raymondl,† U. S. Commissioner of Mining Statistics from 1869 to 1876, contain most of the available information about the early smelting operations in the Rocky Mountain region, and much is in the early volumes of the Transactions of the American Institute of Mining Engineers. The monograph by S. F. Emmons2 though not published until 1886, contained an elaborate description of the smelting works operating in 1879. Otto H. Hahn3 wrote a valuable paper in 1883, on smelting prac-

Jan 1, 1937

By Harry Power

THE relative merits of air and natural gas as propulsive agents in pressure drive operations have been discussed for a number of years. When air or gas is introduced into the sand, various factors lead the operator to the selection of what he believes to be the proper propelling medium; but when the question of relative drive effect is raised, several physical and chemical premises must be taken into consideration in arriving at a conclusion as to the superiority of one medium over the other. Dow and Calkins1 and Beecher and Parkhurst2 have contributed fundamental experimental work on the effect of dissolved gas in lowering the viscosity and surface tension of crude oil. Herold3 and Tickell4 have indicated that whatever type of reservoir control obtains, gas plays other important parts in the movement of oil towards the well, namely: 1. The propulsive and expansive force of the gas. 2. The "Jamin effect," or resistance to the movement of oil in a porous media due to the formation of gas bubbles. When quantitative studies are made, parallel conditions must be selected whereby we may say definitely whether air is superior to gas as a driving medium, or vice versa. Examples of similar conditions are not easy to find in the field. However, in the laboratory we can make determinations which may lead to general conclusions when applied to the field. The- experimental and research work described here was started at the laboratories of the University of California in January, 1927, and completed in private laboratories at Tulsa, Okla., in February, 1928. The apparatus used was designed especially for the work.

Jan 1, 1928

By Shosei Serata

Stress control methods of mining have been developed separately in at least four different parts of the world in entirely different types of mining -- coal, trona, salt and potash -- during the decade of the 1960s. They all utilized yield pillars as tools for ground control. Today, yield pillars are becoming widely used in under- ground mines in a variety of geological conditions. Stress control methods are effective in stabilizing openings in weak, complex grounds, especially at greater depths. Their advantage is that they utilize existing ground media to stabilize mine openings by altering the stress distribution patterns around the openings, by controlling design parameters such as room width, pillar geometry, and excavation sequence, rather than by using a conventional means of artificial ground support such as roof bolts, cribbing, or arches. Stress control methods, therefore, are suitable for both advance and retreat mining, including total extraction mining. Adaptation of these methods results in substantially greater safety, productivity, and ecnomy over conventional methods. These methods are based on scrutiny of the actual stress conditions in the ground, by both in-situ measurement and computer simulation. This paper provides a summary of stress control methods as developed over the last ten years. The field examples are limited largely to salt and potash mining applications, although the method has been used successfully in other mining applications. The examples illustrate that stress control methods actually address general ground weakness problems -- separation at discontinuity planes, swelling by shale expansion, deterioration by brittle fracture, and interference by ground water. That is, although the principle is developed mainly with reference to salt and potash applications, it is generally applicable to weak ground.

Jan 1, 1983

By Max C. Eastman, V. H. Wilhelm

California had a record year in production and drilling activity, but the results have not been sufficient to keep up with the enormous increase in demand due to war activity. During the year, 164 dry wildcats were drilled, 80 dry wells in proved areas, 31 gas wells, and 1158 successful oil-well completions for a total of 1433 wells, compared with a total of 765 in 1942. With new discoveries of only 20,000,000 and production of 283,000,000 bbl. for the year, total reserves of California oil have decreased more than 250,000,000 bbl. However, revised estimates of the reserves of old fields indicate an increase in the state's reserves of I00,000,000 barrels. The completion of 1158 wells has served only to maintain the maximum efficient daily rate of production at 800,000 barrels. There is evidence in many fields that oil is being withdrawn too rapidly to obtain the maximum recovery, and more rapidly than is conducive to good production practice. Statistics for 1943 as compared with I942 are shown in the table in the next column, Supply and Demand Steadily mounting needs of the military forces and increased industrial consumption raised total demand for all petroleum products on the Pacific Coast to 914,000 bbl. daily in 1943. That all-time record demand was 149,ooo bbl. daily higher than in 1942 and 214,000 bbl. daily above 1941 demand. Despite restrictions due to shortages of critical material, crude-oil production was boosted from 680,000 bbl. daily in 1942 to 779,000 bbl. daily in 1943, the highest level in 15 years. However, the new crude supply plus natural gasoline production and imports from other states totaled only 840,000 bbl. daily, leaving a deficiency between supply and demand of 74,000 bbl. daily. That shortage had to be made up by withdrawals from inventories, which had been steadily depleted during the previous four years. Aboveground reserves, which totaled 159,574,000 bbl. on Jan. I, 1939, were down to ~8.000,000, bbl. at the end of 1943. Significantly enough, the greater part of that decrease occurred during the last six months of I9437 when more than 23,000,000 bbl. was taken from inventories of both crude and products. Although the size of total inventories on Dec. 31, 1943 might appear substantial, about 65 per

Jan 1, 1944

By A. J. Lanza

The prevention of illness among the employees of the mining industry is especially important in view of the importance of the industry, the unsettled conditions of labor, which emphasize the economic necessity for conservation of labor, and for humanitarian reasons. The burden of chronic illness is altogether unwarranted and unnecessary. If the industry is to maintain its labor supply in an efficient manner and keep the standard high, it is essential that it make every effort to keep its labor in good physical condition. The basic principles underlying health conservation are the same for any industry, but they are here applied especially to the mining industry, and more particularly, perhaps, to metal mining, as it is with this phase of the industry that the writer is most familiar, and as it is conceded that metal mining presents more health hazards than coal mining. The first step in the prevention of illness lies in securing employees who are in sound health and free from organic disease. I do not mean that all men who go underground should be physically perfect, but they should be free from organic defects of the heart, lungs, and other organs, or from anatomical defects that would markedly increase their liability to accident. The number of men working underground in mines in this country whose physical condition totally unfits them for such work presents a situation that should not be allowed to continue, and which I believe is not equalled in any other industry in the country. There is but one way to secure men who come up to the required standard, and that is by a thorough physical examination before employment. I am fully aware of the objections felt toward such a procedure by many employers and employees. There is much to be said on both sides, but to any one who is at all familiar with the mining industry as it is today in this country, and who approaches the matter with an unbiased mind, there can be absolutely no doubt as to the necessity for physical examination. As a purely logical proposition this is self-evident, but there remains the further necessity of placing physical examinations on such a basis that they can be administered in a just and equitable manner free from the abuses and suspicions to which they have been subject in the past.

Jan 1, 1919

By S. E. Bretherton

(San Francisco Meeting, September, 1915) DURING the year 1878-79, Anton Eilers, who was then interested in the lead smelting and refining business near Salt Lake City, Utah, made a somewhat radical departure from the regular practice at that time, which was to use but little lime in the slag, with a high percentage of iron. Lime was not only a cheaper flux than iron, but it enabled the metallurgist to make a more siliceous slag, an economical advantage in smelting where the smelting companies had to purchase either iron or lime to neutralize the excess silica, and penalize the ore shippers accordingly. The larger amount of both lime and silica in the slag also made it of lighter specific gravity, and a better separation of the metals and mattes was secured. This change in the formation of slags for lead smelting was brought about by Anton Eilers, prior to the Leadville mining excitement of 1879. We must also give Mr. Eilers credit for the general introduction of the hollow water-cooled cast-iron jacket for the blast furnace. Again referring to the use of more lime and less iron in the formation of slags,. there is no doubt but that it prevents the formation of a great many so-called "sows" in the lead crucible, such as were made in the early history of lead smelting in the Rocky Mountains; these sows consisted of lead, iron, arsenic, sulphur, copper, and other metals, including gold and silver, mixed with unconsumed fuel, and often, after vain attempts to cut them up or melt them to a suitable size for handling, were buried in the slag clumps to get them out of-sight. Another advantage derived from the adoption of high-lime slags. when smelting ore containing arsenic is the production of less speiss (a by-product heavier than matte, resulting from careless operation of the furnace, the lead being driven out of the crucible and sows built up). This speiss, while usually not as rich in precious metals as matte made at the same time, is too valuable to be thrown away; but it is difficult to treat, and it was thrown away or piled on the slag clumps in the pioneer clays of lead smelting in this country.

Jan 8, 1915

By Max C. Eastman, V. H. Wilhelm

California had a record year in production and drilling activity, but the results have not been sufficient to keep up with the enormous increase in demand due to war activity. During the year, 164 dry wildcats were drilled, 80 dry wells in proved areas, 31 gas wells, and 1158 successful oil-well completions for a total of 1433 wells, compared with a total of 765 in 1942. With new discoveries of only 20,000,000 and production of 283,000,000 bbl. for the year, total reserves of California oil have decreased more than 250,000,000 bbl. However, revised estimates of the reserves of old fields indicate an increase in the state's reserves of I00,000,000 barrels. The completion of 1158 wells has served only to maintain the maximum efficient daily rate of production at 800,000 barrels. There is evidence in many fields that oil is being withdrawn too rapidly to obtain the maximum recovery, and more rapidly than is conducive to good production practice. Statistics for 1943 as compared with I942 are shown in the table in the next column, Supply and Demand Steadily mounting needs of the military forces and increased industrial consumption raised total demand for all petroleum products on the Pacific Coast to 914,000 bbl. daily in 1943. That all-time record demand was 149,ooo bbl. daily higher than in 1942 and 214,000 bbl. daily above 1941 demand. Despite restrictions due to shortages of critical material, crude-oil production was boosted from 680,000 bbl. daily in 1942 to 779,000 bbl. daily in 1943, the highest level in 15 years. However, the new crude supply plus natural gasoline production and imports from other states totaled only 840,000 bbl. daily, leaving a deficiency between supply and demand of 74,000 bbl. daily. That shortage had to be made up by withdrawals from inventories, which had been steadily depleted during the previous four years. Aboveground reserves, which totaled 159,574,000 bbl. on Jan. I, 1939, were down to ~8.000,000, bbl. at the end of 1943. Significantly enough, the greater part of that decrease occurred during the last six months of I9437 when more than 23,000,000 bbl. was taken from inventories of both crude and products. Although the size of total inventories on Dec. 31, 1943 might appear substantial, about 65 per

Jan 1, 1944

By E. S. Moore

The Kolar gold field has been for a long time the most important gold-producing area of India. It is situated in the Skate of Mysore, southern India, and not far from the City of Bangalore. The productive field is about 3 miles long and in it a gold-bearing quartz vein varying in width from 1 in. to over 10 ft. is worked. The vein carries high values to great depths and many of the mines have paid large dividends. Geological Formations In KolaR Region The rocks of the Kolar region are pre-Cambrian in age and bear a close resemblance to some of the pre-Cambrian formations of America. The oldest rocks seen are basic lavas, now mostly altered to hornblende-schists, with which is associated some banded iron-formation; these rocks are similar to the Keewatin schists and iron-formation in the Lake Superior region. The schist is cut by the gold-bearing quartz vein. In certain parts of the area there is also a conglomerate containing pebbles of granite, jasper, and schist. The matrix resembles a hornblende-schist and is intruded by small granite dikes, which in some cases have been pinched off by squeezing of the rock. This has led Dr. W. I?. Smeeth, Chief Inspector of Mines of Mysore, to whom the writer is greatly indebted for information regarding this area and for his hospitality while visiting the field, to regard this conglomerate as a breccia due to crushing of granite dikes in the schist. Dr. J. W. Evans has regarded the conglomerate as probably a squeezed glacial boulder clay. From analogy with pre-Cambrian conglomerates in America, the writer regards it as a metamorphosed rock similar to our basal Huronian conglomerate. However, the main bearing which it has upon the problem under discussion is the apparent fact that it is younger than the schist and that it indicates the presence of a syncline in the rocks cut by the quartz vein. Surrounding the area of schist and conglomerate is a large mass of granite-gneiss resembling the Laurentian gneiss of the Lake Superior region. Still later than the rocks mentioned above are basic intrusions which cut the quartz and schists; in the mines these are known as trap. One dike of this type is 50 to 60 yd. wide.

Jan 1, 1920

By K. Hodgson, N. C. Joughin

The detailed mechanism of rockbursts and other forms of damage due to rock failure in underground mining is as yet unknown. Studies of the energy changes which necessarily occur when an excavation is made underground seem to provide the best understanding of the phenomena leading to rock failure and damage (see Cook 1). It is common knowledge that the damage and rockburst hazard increases with depth and is greatest at remnants and in regions mined in an irregular manner. The rate at which energy is released as an excavation is enlarged provides an objective parameter to describe mining geometry in terms which are significant to studies of rock failure. In this paper, it is shown empirically that the rate of energy release per unit area increase in the size of an excavation is closely related to seismicity and incidence of damage in the mine. Consequently, it is suggested that the energy release rate is an important parameter in the design of underground mine layouts. Observations were made at two mines: the East Rand Proprietary Mines, Ltd. (E.R.P.M.), at a depth of about 9000 ft, and at Harmony Gold Mining Co., Ltd., at a depth of about 5000 ft. At both of these mines continuous recording seismic networks were in operation. (See Cook and Joughin.3) DESCRIPTION At E.R.P.M. the gold-bearing reef dips at approximately 35 degrees and is presently being mined at depths from 8000 ft to 11,000 ft below surface. The rock surrounding the excavation consists of a very homogeneous quartzite extending far into the hangingwall and footwall. The stoping width is approximately 40 in.

Jan 1, 1967

By M. R. Geer Olds, H. F. Yancey

THE increase in the number of coal-cleaning plants employing dense-medium processes occurring since 1946 is especially interesting when viewed historically. Both sand and magnetite were introduced as material for heavy mediums at about the same time, sand in the Chance process in 1921 and magnetite in the Conklin process in 1922, but from that point on their records diverge. The Chance process enjoyed a steady growth from its inception, whereas no additional magnetite plants were built in the United States for over 20 years. Then, following the close of the World War 11, magnetite was again introduced, this time with marked success. During the following years some 47 plants employing magnetite medium were built. This rapid growth of dense-medium cleaning has been concurrent with widespread adoption of full-seam mining on one hand and a return to a more competitive market on the other. At a time when changing mining practice has provided cleaning plants with dirtier coal and changing market conditions have simultaneously demanded a cleaner product, the industry has through necessity turned to improved preparation. The inherently greater sharpness with which dense-medium processes can separate coal from impurity is thus helping to hold the line against ever-increasing mining costs and at the same time assisting materially in retaining badly needed markets. Although dense-medium cleaning unquestionably offers a distinct advantage when the washing problem is difficult, other methods can provide almost equally high efficiency when the coal is easy to wash. Moreover, fine coal cannot yet be treated by heavy medium in a proved process, although the Driessen cyclone is in the pilot-plant stage. Most of the present types of dense-medium equipment have been in use only a few years, and the dearth of information in the literature concerning their performance characteristics is entirely understandable, Nevertheless this information is necessary if the process is to be intelligently applied to individual cleaning problems. Without data on the efficiency of a process in a particular type of separation, it is difficult to assess the advantage to be expected from it. Similarly, the role of particle size in heavy-medium separation is important in some cases, yet there is little published information on this aspect. To mention only one more of the numerous points on which essential information is lacking, the bearing of medium characteristics on performance has been discussed only in qualitative terms. It was with the hope of providing information on some of these points that the Bureau of Mines built a dense-medium pilot plant for cleaning coal at its Northwest Experiment Station in Seattle in 1950. The plant has been operated continuously since that time, and over 50 runs have been made on 7 coals exhibiting a wide range of washability characteristics. An idea of the magnitude of this work will be gained from the fact that examination of the plant products has involved some 600 float-and-sink separations and about 2500 ash determinations. A laboratory pilot plant is especially well adapted to investigate many aspects of performance because close control over test conditions can be exercised and because a large number of tests can be made rapidly. On the other hand, factors such as consumption of medium and other cost items can be investigated satisfactorily only in a commercial plant. Actually, the two forms of investigation should be complementary, with the laboratory work pointing the way for confirming tests in commercial units. Pilot Plant The dense-medium pilot plant employed for this work comprises a 24x30-in. drum-type separating vessel, a 12-in. densifier, a 12-in. magnetic separator, a 26-in. x 9-ft vibrating screen, and the necessary pumps and conveyors for handling materials. Arrangement of these units corresponds with the flowsheet used in most commercial plants, except that a thickener is not provided for the feed to the magnetic separator. Coal and refuse discharge from the separating drum to the vibrator, which is divided longitudinally down the center. Medium draining through the first 3 ft of the screen is recirculated directly to the drum. Sprays on the middle 3 ft of the screen rinse medium from the products, and the last 3-ft section is for dewatering. Dilute medium from the rinsing and dewatering sections is pumped to the magnetic separator, where magnetic solids are recovered. These are pumped to the densifier, from which they return to the medium-drainage sump by gravity through a demagnetizing coil. The drum-type separating vessel is a scale model of a commercial unit. Feed enters axially at one end of the drum just below the surface of the bath, and float material overflows through a circular opening at the other end. Particles sinking to the bottom of the bath are picked up by lifting flights bolted to the inner wall of the drum, elevated out of the bath, and sluiced to the vibrating screen. Baffles suspended in the bath prevent float material from entering the sink-lifting flights. About 8 gpm of medium is used to sluice the feed into the drum. An additional 15 to 24 gpm, depending upon operating conditions, is added through two pipes dipping into the bath behind the baffle on the side where the sink-lifting flights enter the bath. The bath available for separation is 2 ft long and 13 in. wide, giving an area of 2.08 sq ft. Depth of bath from the surface to the top of the sink-lifting flights, measured vertically below the axis, is 6 in.

Jan 1, 1954

By R. L. Dietrich

[ ] We at The Dow Chemical Co. have recently done some work on the deformation of magnesium alloys and although it is far from complete there have been a few observations which may be of interest in connection with this paper. In the first place, I should like to point out that the deformation of polycrystalline magnesium alloys has not been completely explained by the work on single crystals. Bakarian and Mathewson found slip on the ( 101) and {002) planes, and (102) twinning as the deformation mechanisms in magnesium single crystals, but in compression when the (002} planes were within ii° of parallel t0 the compression surfaces, fracture occurred at all temperatures up to 340°C (644°F). In commercial working processes, particularly in rolling, an orientation is quickly produced which should be unfavorable to further deformation by the three established mechanisms. The first few reductions in rolling quickly produce an orientation having

Jan 1, 1947

By A. Muan

Liquidus data are presented for mixtures in the ternary system FeO-Fe2O3-SiO2 in equilibrium with a gas phase with O2 pressures ranging from 10-10.9 to 1 atm. Data obtained are combined with previously published data to construct lines of equal 02 pressures and lines of equal CO2/H2 mixing ratios along the liquidus surface. Courses of crystallization of selected mixtures under conditions of constant total composition, constant O2 pressures, and constant CO2/H2 mixing ratios are discussed. PHASE equilibrium studies of silicate systems where iron is one component are complicated by the fact that iron readily occurs in three different states of oxidation: Fe3+, Fe2+, and Fe0. Success or failure in work with iron silicate systems is to a large extent dependent on control of the oxidation state of iron and all investigations therefore must be carried out under carefully controlled atmospheric conditions. Silicate systems containing only strongly electropositive metals (like Na+, Ca2+, Mg", etc.) can, for simplicity, be treated as condensed systems, that is, the gas phase can be neglected and the phase relationships discussed in terms of the phase rule written in the well known simplified form P + F = C + 1. In the case of iron silicate systems, however, the composition of the condensed phases varies with the gas composition, and a complete picture of phase relationships can be obtained only by varying the gas composition over a wide range. In order to understand the phase relationships in the more complicated multicomponent silicate systems with iron oxide as one of the constituents, a knowledge of the ternary system FeO-Fe2O3-SiO2 is essential, since it constitutes a bounding portion of all such systems. It was with this in mind that the present study was undertaken. Previous Work A considerable amount of work has been done on various aspects of the chemistry and metallurgy of systems containing silica and iron oxides. The two bounding binary systems FeO-Fe2O3 and FeO-SiO2" The first attempt to obtain information on phase relationships of iron oxide-SiO, mixtures at different 0, pressures was made by Greig.' Darken" determined the melting points of iron oxide on solid silica under various atmospheric conditions. Darken did not determine experimentally the composition of the melts at liquidus temperatures but discussed very ably the principles involved in applying the phase rule to the system. In a recent study Schuhmann, Powell, and Michal8 determined experimentally the liquidus surface of a portion of the ternary system and combined the new information with data in the literature to construct a phase diagram. Their method was briefly as follows: Homogeneous mixtures with various contents of SiO2, FeO, and Fe2O3 were made up by melting together stock mixtures in various proportions. Samples of the homogeneous mixtures, the compositions of which were determined by chemical analysis, were then heated in platinum crucibles in an inert atmosphere until equilibrium among the condensed phases was achieved. The samples were quenched to room temperature and the phases present determined by microscopic examination. Assuming that no change in composition takes place during the equilibration run in inert atmosphere, the liquidus surface can be determined, but no information is obtained regarding the partial pressures of 0, of the gas phase in equilibrium with the condensed phases. The author's method, to be described in the next section, permitted the location of points at the liquidus surface as well as a calculation of the corresponding partial pressures of O2. Experimental Method General Procedure: The standard quenching technique was adapted for a study under controlled variable atmospheric conditions. Premelted mixtures of silica and iron oxides in platinum envelopes were held at constant temperature under chosen atmospheric conditions until equilibrium was reached among solid, liquid, and gas phases. The sample was then quenched to room temperature, the phases present identified, and, for the most significant runs, the composition was determined by chemical analysis. The corresponding partial pressure of 0, was calculated from known equilibrium constants of the gas reactions occuring in the furnace atmosphere. Materials: Starting materials were oxides of commercially highest available purity; cp silicic acid was dehydrated by heating to 1350°C for 6 hr and cp Fe2O3 was dried at 400° C for the same length of time. Samples of 10 g were made up by mixing

Jan 1, 1956

By S. Leber

Pole figures and pole distributions were used for the quantitative detevinination of the preferred orientations in swaged tungsten rods and the effect of subsequent wire drawing on the texture. In the swaged rod, the preferred orientation could best be described as a pseudo (111-112) [110] cylindrical texture. A secondary component was assigned the indices (110) [001]. Further reduction by swaging retained these cylindrical textures. Wire drawing caused lattice rotations about the wire axis, converting the cylindrical texture into a normal fiber texture. The conversion was initiated and proceeded lnost rapidly in the center of the wire. The (110) /001] component was converted into a (110) fiber texture by wire drawing. The effective rotations were about axes contained in the lransverse plane. The preferred orientation associated with tungsten wire usually has been assumed to consist of a (110) fiber texture. This implies rotational randomness around the wire axis. Leber1 has shown that rotation about the wire axis may be restricted resulting in a preferred orientation designated as a cylindrical texture. Specific crystal planes tended to remain aligned parallel to the wire surface. This texture seemed to be the result of the swaging operation used in the intermediate stages of fabrication. Bhandary and cullity2 detected similar textures in swaged iron wires. Peck and Thomas3 suggested that the preferential alignment of crystal planes parallel to the wire surface was the result of tangential flow, characteristic of swaging. Wire drawing, following swaging, twisted the crystals about axes parallel to the wire axis, converting the cylindrical texture into a normal fiber texture.4 In this investigation, quantitative techniques were used to more accurately characterize the cylindrical texture and to study its conversion into a normal fiber texture. PROCEDURE The material investigated was lamp-quality tungsten. Three ingots were rod-rolled and swaged to 112 mils diameter, and were then drawn to 10-mil wire. Samples were obtained after each drawing pass. (110) and (200) pole figures were obtained from samples prepared as shown in Fig. 1. To form the sample shown in Fig. l(a), l-in. lengths of wire were glued side by side to form a l-in. square. The composite was ground and electropolished to form a diametral reference surface. For certain specific tests, samples were prepared as shown in Fig. l(b). This composite was made from 10-mil-thick strips prepared by grinding on parallel longitudinal planes. The polished reference surface in this case was, in essence, the wire surface. The two forms of samples [~igs. l(a) and l(b)] were related by a 90-deg rotation around the wire axis. Because of ease in preparation, most data was obtained from the diametral samples. The X-ray data were obtained using a Siemen's pole-figure goniometer. These data were not corrected for absorption or defocusing effects, since only the angular locations of the intensity maxima were of interest. Regions of the pole figure more than 80 deg from the center were not investigated. Partial monochromatization was achieved by the use of unfiltered copper radiation and a krypton-filled proportional counter. No evidence of spurious white radiation effects5 could be detected. Therefore, more elaborate X-ray techniques were not required. Intensity levels were chosen to show all pertinent details of the orientation distributions. The reference plane for the pole figures was the diametral section. The orthogonal reference directions, shown in Fig. 1, were the wire axis, the radial axis per-

Jan 1, 1965

By J. L. Bray

IT is well known that iron markedly improves the physical properties and casting characteristics of aluminum bronzes. The use of 1 to 4 per cent iron as the principal modifying addition has become common practice in many foundries melting aluminum bronzes. Although the beneficial effects of iron are unquestioned, there is some uncertainty regarding the structural changes caused by it in the basic copper-alumi-num system. It is agreed that a new constituent appears in abundance when the iron content reaches 2 to 4 per cent. This constituent, which frequently occurs in shapes resembling clover leaves, is sometimes assumed to be an aluminum-iron intermetallic compound. If this were correct we might expect a change in the structural relationships of the matrix in the direction of decreased aluminum content. On the other hand, it has been reported that iron has a negligible effect in altering the fundamental relationships of copper-aluminum alloys1. Others2,3 have reported an additive coefficient. Apparently it will be necessary to know the equilibrium relationships between the phases of the copper-aluminum-iron alloy system to establish any such theory as fact. When this has been done it may very well be that a further revision in the structural relationships may be necessary to describe the changes to be expected in commercial cast alloys. It was with this latter problem before them that the authors attempted to

Jan 1, 1936

By Lynn G. Howell, Alex Frosch

In a previous article1 we have described a technique for measuring the relative intensities of gamma rays from the radioactive elements occurring naturally in geological formations along the walls of a borehole. The apparatus consisted of two Geiger-Müller tubes mounted inside a pressure-tight chamber. Each counter tube was coupled separately to an amplifier and a frequency meter at the surface by means of a multiconductor cable upon which the chamber was suspended. The output currents of the two frequency meters were recorded on a photographic paper as the chamber was moved in the hole. These traces showed remarkable correlation with the geologic formations, as evidenced by comparison with commercial electrical logs.2 Owing to the penetrating power of the gamma rays, logs may be taken in both open and cased boreholes. The apparatus has recently been changed somewhat. One of the counter tubes has been removed and a stage of amplification has been added inside the chamber. This arrangement seems to give a more favorable signal-to-noise ratio and satisfactory logs can be now made in cased holes and also in open holes as previously. Briefly described, the chamber moving in the hole is made of 3½-in. drill pipe and is about 10 ft. long. There is an additional extension about 2 ft. long at the top, inside which cable connections are made. The Geiger-Müller tube is mounted inside the bottom end of the chamber. Above this is the vacuum-tube amplifier with its batteries and transformer. In the top part of the chamber, small 45-volt batteries are mounted, which in part supply the high voltage for the counter tube. Additional voltage is supplied from the surface through the multiconductor cable upon which the chamber is suspended. Also, the output of the transformer in the single-stage amplifier is coupled to another single-stage amplifier at the surface through this cable. The surface amplifier is coupled to the Thyratron-controlled frequency meter, the tank circuit of which consists of a one megohm resistor across which is a bank of condensers varying in

Jan 1, 1940