Search Documents

By H. A. Bedworth, W. H. Bassett

The amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors' laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hampe1 that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe's method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen. Heath4 found that the loss in weight after heating in hydrogen did not represent the true oxygen as cuprous oxide but included also gases derived by the metal from the fuel and refining in the furnace, and any trace of mechanically held moisture. He found, further, that the copper after ignition retained hydrogen equivalent to about 0.01 per cent. Heath proposed to determine the amount of occluded gases by preliminary ignition for 20 min. in pure carbon dioxide—and to correct the error caused by absorbed hydrogen by subsequent ignition and cooling in carbon dioxide, finally replacing this gas with air.

Jan 1, 1926

By K. A. Johnson, H. F. Yancey

Physical properties have been used for a long time in characterizing different kinds of coal, and such physical properties as friability and slacking have been included along with chemical properties in grouping coals according to the widely used system of classification adopted by the U. S. Geological Survey. Nevertheless, the usefulness of physical properties for classifying the different ranks or kinds of coal has been limited because it has not been possible to express these properties in definite form as numerical values. Because of the present wide interest in the formulation and adoption of a satisfactory system of coal classification, the Northwest Experiment Station of the U. S. Bureau of Mines, in cooperation with the College of Mines of the University of Washington, has recently completed a study of the physical and chemical properties of approximately 100 different coals ranging in rank from lignite to anthracite. Purpose and Scope For this investigation samples were collected in approximately 45 mines and prospects in Washington and 23 mines in other states. The following studies, in addition to proximate and ultimate analyses, were made of the samples: Determination of (1) friability, (2) slacking or weathering characteristics, (3) yield of products by low-temperature carbonization in a laboratory retort, and (4) agglutinating value. Most of the coals examined were subjected to each of the tests enumerated, but with coal of some ranks this was unnecessary in some instances, and in others it was not feasible to do the work involved. A report which includes the analyses of the coals and the details of the methods of examination used in the investigation is being published by the Bureau of Mines.' It is the purpose of the present report to show the results of the friability, slacking, low-temperature and agglu-

Jan 1, 1932

By W. A. Wood, H. L. Wain, R. I. Garrod

The mechanical behavior of recrystallized chromil~m of high purity has been studied, principally in torsion and to a lesser extent in tension, at temperatures between —196oand 350oC. Depending upon the conditions of test, the material may show brittle or ductile behavior or an intermediate or subduc-tile state having some of the characteristics of each. This latter state existed at temperatures between approximately ±50°C and was characterized by a) extensive creep at stresses well below the normal fracture stress, b) nonelastic loading/unloading effects during creep, c) strain softening under cyclic loading, and d) final failure of a brittle type. Suggestions are made on the dislocation processes and interactions which give rise to subductile behavior The ductile-brittle transition in bee metals has been studied mainly by tension and bend tests. These methods, however, favor crack propagation which may follow too closely on initiation for detailed study of the transition itself. For work of this nature, therefore, other modes of deformation less favorable to crack propagation may be preferable. This paper describes a study of the ductile-brittle transition in chromium which is based mainly on torsional testing although a few subsidiary experiments were made in tension. It appears to reveal at the transition an intermediate state that cannot properly be described as either brittle or ductile. Torsional tests on chromium have been made by other workers1 but not, as here, primarily for study of this intermediate state. EXPERIMENTAL The chromium, in the form of swaged rod, was prepared by techniques already described.' The particular material used was one in which the main impurities were 0.03 wt pet 0 and 0.006 wt pet N and one in which transition from ductile to brittle states in torsion conveniently fell at about room temperature. For torsion, test specimens were from 5/16-in.-diam rod to provide test portions 1-1/4 in. long by 7/32 in. diam, a twist of 1 deg thereby corresponding throughout this paper to 0.0015 surface shear. The specimens before test were annealed for 2 hr at 1200°C in vacuo, which left them with a re-crystallized grain size of about 0.01 mm, and then electropolished. They were tested under dead-weight loading in an apparatus in which they could be surrounded by a furnace or cooling chamber, tests in practice being made at various temperatures between -196" and +350°C. For tension tests, cylindrical specimens were prepared in a similar manner and tested at room temperature under dead-weight loading. RESULTS (TORSION) Subductile State. The state described above as intermediate between brittle and ductile may be perhaps best defined by reference to torque/twist curves at various temperatures. These are grouped in Fig. 1. Below about -50°C the material was brittle, in the sense that it exhibited little plastic deformation under stress and fractured by cleavage along planes of maximum resolved tension, which in torsion produces the well-known helical type of fracture. The deformation is typified by the curves for -196" and -150°C in Fig. 1; it shows a slight but progressive deviation from linearity above a certain torque, here about 50 lb-in., until fracture occurs at about 95 lb-in. A feature to which it is desired specially to call attention is that under none of the loads did the specimens show significant creep.

Jan 1, 1964

By Kun Li, Alex Simkovich

The rate of dissolution of alumina in carbon-saturated liquid iron has been studied experimentally in a system where alumina was in the form of a cylindrical rod immersed in an iron bath contained in a graphite crucible. Data obtained consisted of the concentrations of aluminum in the melt as a function of time. In the case of static experiments, the data are shown to agree with theoretical prdictions based on the diffusion of aluminum.. The rate of dissolution was greatly increased by the rotation of the alumina rod. It is concluded that the diffusion of aluminum from the alumina/metal interface is the rate-controlling step. In the past, thermodynamic investigations of systems encountered in ferrous process metallurgy have received widespread attention. More recently, considerable work has been devoted to the study of kinetics associated with these systems in an effort to determine their rate controlling mechanisms. The alumina-iron system is of great importance in ferrous metallurgy. Yet information concerning kinetics of reaction in this system is seriously limited. The present study was made in order to establish the rate-controlling step for dissolution of solid alumina in liquid iron. LITERATURE REVIEW A number of papers concerning dissolution of solid metals in liquid metals have been reported in the literat~re. Generally, for these simple systems, dissolution is controlled by mass transfer of the dissolving species. Complex systems involving dissolution of solid metal carbides and oxides in liquid metals and slags have been studied to a much lesser extent. Skolnick5,6 reported on the reaction between liquid cobalt and poly-crystalline cylinders of tungsten carbide, in which the cylinders were dissolved while being rotated about their longitudinal axes at various speeds and temperatures. As a result of unexpected preferential grain boundary attack by the liquid cobalt, large errors in the measured dissolution rates occurred because of loss of tungsten carbide grains to the liquid cobalt. Nevertheless, it was possible to establish that the liquid Co-W carbide reaction was not controlled by mass transfer. In a similar approach, cooper7 was able to show that artificial sapphire rods, (alumina single crystals) dissolving in lime-alumina-silica slags obeyed a mechanism of mass transfer control. Here, again, the rods were rotated at various speeds and temperatures, and the process was followed as a function of these variables. Forster and Knacke8 took a practical approach to reaction between slags and refractories. By blowing argon through refractory cylinders of silica, silli-manite, or dolomite and directing the gas to rise along the slag-refractory interface, it was possible to increase the rate of mass transfer. Although the method was admittedly crude, it nevertheless permitted an evaluation of the relative stabilities of refractories with respect to slag attack. Data were interpreted on the basis of mass transfer control. EXPERIMENTAL TECHNIQUE Apparatus. An illustration of the apparatus used in this study is shown in Fig. 1. The furnace consisted of a Morganite recrystallized alumina tube wound with a molybdenum coil. A secondary molybdenum heater was mounted around the upper half of the primary coil to aid in controlling the thermal gradient within the furnace. The primary heater tube was 3 in. in ID and 30 in. long. A reducing mixture of 95 pct N and 5 pct H was maintained around the heating elements. Thermal insulation was provided by alumina powder. The chamber within the primary combustion tube contained a boron nitride block near the top to assist in controlling the thermal gradient to the furnace and also to provide a bearing surface for the rotating graphite shaft. The outside diameter of the graphite shaft was $ in. A separate threaded graphite specimen holder was screwed into the end of the shaft. The holder contained a tapered hole drilled into the end to guide the oxide specimens as they were pressed into it for mounting. Additional guidance for the rotating graphite shaft was furnished by a water-cooled bronze bushing attached to the top of the furnace. A steel clamp was fastened to the upper end of the graphite shaft and rested on a thrust bearing; the shaft and clamp were driven by a dc motor through a set of gears. Two O-rings located immediately above the bronze bushing maintained a gas-tight seal about the graphite shaft. The lower half of the alumina tube housed the crucible and charge, which were placed on a 3/4-in. diam movable alumina support tube. With this arrangement, charges could be inserted into or removed from the furnace while the hot zone was maintained at or above 1000°C. To control the temperature of the furnace, the thermocouple was mounted inside the support tube and in contact with the crucible bottom. Stray electric fields in the furnace were of sufficient intensity to cause erratic indications by the thermocouple. By enclosing the thermocouple protection tube in a molybdenum sheath and grounding this shield, the problem was eliminated. Output of the thermocouple went to an automatic continuous balance controller. Procedure. A typical run was as follows. First, electrolytic iron was premelted in graphite crucibles and cast into graphite molds with the same configura-

Jan 1, 1970

By Harrison R. Cooper

Computer process analysis and control techniques are overcoming major hurdles to acceptance in the mineral industry. With the growing list of new advances characteristic of a rapidly maturing discipline, management of the companies on the leading edge are keenly aware of the advantages of using computer methods in process applications. Significant advancement is already evident in such technical areas as operations research, mathematical modeling, statistical methods, and computer-based procedural techniques. The early advances during the past decade are already documented in prior symposium proceedings of this series. Thus, the currently active areas of the advancing technology are emphasized here. This section deals with applications in pyrometallurgical and kiln processes. The two sections which follow deal with concentrating operations from two points of view: 1) mathematical modeling, and 2) on-line control. In the metallurgical field, emphasis on developing effective process computer applications for the steel industry began in the late 1950's. Simulation techniques also received substantial attention. The steel industry was soon joined by the cement industry in the development of computer methods for process applications. Computers were in use for feed-material blending and kiln control in the early 1960's. Computer development in other pyro processes, such as aluminum reduction and glass-making, also marked significant advances by the mid 1960's. Aluminum smelter potline control is a nearly universal application at this point, and the development of glass furnace computer process control represented a recent important technical advance in digital control techniques. Steel Hot strip rolling was the earliest significant process computer application in the metallurgical industry. Computer control of rolling mill operations is now a steel mill standard component, particularly in plants newly placed into production. 1, 2 Initial computer installations principally carried out procedural routines in setting mill clearances for production lot control. Recent developments are leading toward feedback control based on mathematical model techniques. 3

Jan 1, 1969

By George S. Rice

The increasing use of mechanization at the face of the workings in coal mining and the consequent necessity of special supports of the roof has led, in several countries, to considerable scientific investigation, including physical tests in mines as well as on specimens of roof rocks to obtain data on the behavior of the immediate roof strata and on the effect of its pressure on supports while the coal is being mined. The investigations discussed in this paper do not include studies of the ultimate effect of subsidence and movement of the roof rock over the mine excavation, upon higher strata and the surface, but are confined to the immediate underground effects in the workings. The more recent principal investigations which have been brought to the attention of the writer are as follows: Germany.—The trial of strip packing, the usual method employed in Great Britain in longwall workings, as compared with complete packing heretofore used in Germany and in France to minimize subsidence; the behavior and strength of metal props under load; the testing of the strength of coal measure rocks, in the laboratory of the Technical High School of Breslau; and an investigation, by a special commission, concerning "bumps" as a possible cause of instantaneous outbursts of gas in coal mines of Lower Silesia. France.—The cause of instantaneous outbursts of gas in the Gard mines and tests by the official French experimental organization of the "electrical resistivity" of coal as a possible means of detecting a condition preceding an instantaneous outburst. Great Britain.—The subsidence of the roof and rise of the floor preceding and during excavation of the coal, in longwall and in room-and-pillar or bord-and-pillar workings; the compression and lateral movement of the road packs in longwall back from the face; the extent of separation of the immediate roof layers from the higher strata following mining excavation;

Jan 1, 1932

By Robert T. DeGavre

The $650 million financing for Into Ltd.'s Soroako nickel project is a story worth telling-not only because the project itself represents a significant achievement but also because there are certain important lessons that can be derived from our experience in financing the project. A critical appraisal of the methods and successes in the financing plan is presented in this article, in light of goals which Inco sought to achieve. A technical assessment of the project is not included, since Inco Ltd. has submitted a series of papers on this subject at the International Laterite Symposium as part of the 108th Annual Meeting of AIME in February 1979. Progress in developing and financing the project is encapsulated in the accompanying project factsheet.

Jan 3, 1979

By David N. French

In a recent paper, Miyoshi, Hara, and sugimotoL have shown that hardness increases and crack resistance decreases with polishing time in tungsten car-bide-cobalt alloys. They attribute the changes in hardness and crack resistance to cold working in these alloys. More recently Exner2 explains the decrease in crack resistance with the amount of material removed (polishing time) by suggesting that polishing removes a high compressive residual surface stress due to the initial grinding operation. He cites previous work on steel to show grinding can induce surface compressive stresses but offers no direct experimental measurements to support this in cemented tungsten carbides. In recent work we have observed changes in residual stress in the W C phase as measured by X-ray diffraction techniques with changes in polishing conditions.3 As a result of the work of Miyoshi et al.,L a brief study was undertaken to investigate the effects of polishing and grinding on the residual stress in the WC phase and have been reported.4 A single composition of tungsten carbide —10 wt pct Co was used. Two initial conditions were studied: an annealed condition with about -30,000 psi residual stress from the differences in thermal coefficients of expansion of WC and cobalt and, on the same specimen, a surface ground with a 150 grit diamond wheel. Stress was measured in the WC phase using X-ray diffractometry as a function of the amount of material removed by metallographic polishing with 6 diamond paste. The results are shown in Fig. 1. Two things are noted, 1) polishing with 6 p diamond paste has little effect on the annealed sample and 2) the magnitude of the grinding stress is markedly reduced as material is removed. By the time 0.1 mil is removed the surface has a metallographic polish satisfactory for light microscopy examination. Thus the surface, even though polished, can still retain most of the stress due to grinding. Since WC is itself slightly ductile, it seems reasonable that high compressive stresses can be generated in the surface by the plastic deformation accompanying grinding. Exner2 suggests, by analogy with steel, that as a result of grinding both WC and cobalt in the

Jan 1, 1970

By Thomas M. Drown

I DESIRE to communicate to the Institute the results of a few analyses which bear on the condition of carbon in gray and white iron. These analyses were made in the course of an investigation, now in progress, of the chemical composition of "chilling" irons. It will be remembered that Bell says he found no material difference in the amount and condition of carbon in gray and white pig iron made at the Clarence furnace, in England, and he therefore refers the difference in color and appearance in these two varieties of iron to the size of the particles of graphite. I quote from his "Chemical Phenomena of Iron Smelting:" "The inference I would draw from the information afforded by these analyses is, that the condition of iron in respect to its so-called 'richness' is, within certain limits, entirely independent of its chemical constitution.. .. In the fluid state, I conceive the carbon, so taken up, confers upon the iron the property of fusion much below the temperature at which the pure metal melts, and the carbon itself may be regarded as dissolved in the iron. If, during the process of manufacture, the pig metal has been formed at a low temperature, consolidation, I imagine, takes place under such circumstances that the crystals are so minute, and the carbon which is separated assumes the uncombined or graphitic form in particles so minute as to be invisible, and, in consequence, the iron is white. If, on the other hand, the furnace is working at a very high temperature, the intensely heated iron crystallizes with large facets, upon which the extruded carbon assumes the condition of distinct plates or flakes. Should the temperature be less intense, these crystals are of smaller dimensions, and the separated carbon is less conspicuous, and, as the temperature of the furnace declines, the crystals decrease in size, as do the flakes of carbon, until both disappear in white iron.. .. Returning, then, to temperature as the cause of differences in quality of pig iron, the 'chilling' of gray metal, and its conversion into white, may be regarded as the effect of preventing, by rapid cooling, the formation

By C. Baldwin Sawyer

J. S. Vanick,* Washington, D. C. (written discussion).—To those who have been confronted with the study of the gas-metal reactions, this paper is a most welcome contribution. My personal interest in work bearing upon this general problem, stimulated by an appreciation of the difficulties inherent to problems of this type, prompts a few words of discussion. Table 2 of the paper shows a gradual increase in the nitrogen content with an increase in pressure, and an interpretation follows in which nitrogcn is used as the compressed medium when the conditions admit that cyanogen gas could be active as a contaminating ingredient. Fusions of electrolytic iron made in the induction furnace in an atmosphere of deoxidized nitrogen and out of contact with contaminating materials have shown no microscopic evidence of -a nitrogen increase; using a refractory-lined graphite crucible in the furnace under the same conditions or admitting air often resulted in the occurrence of nitride needles in the solidified melt. These results suggested that a nitrogenous compound served as a vehicle for the introduction of nitrogen and that such compound was not available when the pure gas and carbon-free refractory were used. The fusion of pure iron in pure nitrogen is perhaps a matter of theoretical interest. The author's work serves a more practical purpose when applied to steels rather than iron. Table 2 reports the absence of nitride needles in melts made under pressure of one atmosphere, although the quantity of nitrogen present would seem to exceed microscopically detectable percentages. In some recent work29 on carburized iron, nitride needles have been observed in areas analyzing as low as 0.015 per cent. nitrogen. This low percentage of nitrogen would indicate that the solubility limit is less than 0.030 per cent. for hypoeutectoid steels. There is the possibility that the areas of pearlite which exist in a hypoeutectoid steel restrict the distribution of nitrogen and limit its presence to the ferritie fields. In view of this work and the references quoted by the author, I am led to expect that the value for the solubility of nitrogen in solidified iron may approach

Jan 1, 1924

By R. A. Liddle

Intermitt'en'I'ly during the past 10 years showings of oil and gas in tests drilled in the eastern part of Texas have stimulated the search for production. Tests on the flanks of the long-known salt domes, principally Keechi and Butler, have found oil in small quantity in the Woodbine formation of the basal part of the Upper Cretacrous. In the central part of Cherokee County, Colliton et all in 1926, in their Clapp No. 2 found a good showing of 37" B6. oil at about 3500 ft. Several wells were drilled in 1926 and 1927 as a result of this showing. On Jan. 22, 1927, Humble Oil & Refining Co. wildcatting on Carey Lake salt dome, obtained commercial production in its Clark No. 1. This inaugurated intensive exploration both for salt domes and for other types of structure. As a result several new domes and a few promising structures of other types have been discovered. Development in East Texas durinG 1927 Carey Lake Dome Location.—On the Neches River in Anderson and Cherokree counties, 10 miles west of Jacksonville, Cherokec (lounty. (Fig. 1.) date of Discovery.—During 1925 geologisls of the Humble Oil & Refining Co. working in the Neches River valley discovered slight surface fracturexs, cratic dips, and slickensided clays and sands in green-sands of the Mount Selman formation north of Carey Lake. A number of core tests were drilled by the Humble Oil & Refining C'o. during 1925 and 1926, some more than 1500 ft. deep, to check their surface obsuvations of faulting, and the possibilities of a salt dome. On May 16, 1927, solid rock salt was reached at 2142ft. in the first deep test on the prospect. Surfacc Indications.—Surface indications of the Carey Lake dome, though not as evident as manifestations at the previously known domes of Palestine, Keechi, Butler, Grand Saline, Steen and Brooks, are more noticeable than on any of the domes discovered in 1927. F. E. Poulsen, of the Pure Oil Co., who examined the area before the deep tests were drilled, noted the alignment of erratic surface dips which suggested faulting, especially in conjunction with slickensiding, and the local deflec-

Jan 1, 1928

By Walter Crafts, C. M. Offenhauer

IN the course of study of the heat-treatment of low-alloy steels, the behavior of alloy carbides at subcritical temperatures was found to vary from that indicated by published investigations. In order to establish the ranges of formation of carbides in low-chromium steels, a series of steels containing up to 0.60 per cent carbon and 7.5 per cent chromium has been investigated with respect to the type of carbide formed after quenching and tempering at sub-critical temperatures. The types of carbide formed as products of austenite transformation to pearlitic and pseudomartensitic structures have also been determined. There have been numerous investigations of the carbides in chromium steels and diagrams of the iron-chromium-carbon system.' Westgren, Phragrnén and Ne-gresco2 identified the following carbides in chromium steels: Cementitc............ Fe3C (containing up to about 15 per cent Cr) Trigonal carbide...... Cr7C3 (containing up to about 55 per cent Fe) Cubic carbide........ Cr4C (or Cr23C6) (con- . taining up to about 25 per cent Fe) Orthorhombic carbide , cr3c2 (containing only a few per cent Fe) The most complete information on the iron-chromium-carbon system was supplied by Tofaute, Sponheuer and Bennek3 and by Tofaute, Küttner and Büttinghaus,4 By means of dilatometric and microscopic stzdies, sections of the diagram were established. This diagram showed the presence of the special carbide CI7C3 in steels containing about 2.5 per cent to 12 per cent chromium in low-carbon steels and from about 5 to 20 per cent chromium in I per cent carbon alloys from A1 to room temperature. The present investigation has shown that a carbide inversion from Fe3C to Cr7C3 occurs in chromium steels containing more than about I per cent chromium after hardening and tempering at subcritical temperatures above about 500°C. The type of carbide observed to be more stable in quenched and tempered specimens was also found to be produced by direct austenite transformation in corresponding ranges of temperature and composition. Experimental Procedure The steels used in these experiments were made in magnesia-lined crucibles in high-frequency furnaces and were poured into 2-in. ingots. The ingots were forged into I-in. round bars, and all heat-treatments were conducted on specimens of this section size. Sections of the bar stock 8 in. long were hardened in air, oil or water, depending on the composition, after heating to a temperature sufficiently high to dissolve the carbides. The low-carbon and low-chromium steels were not entirely martensitic after quenching, and contained some ferrite and pseudomartensite. No pearlite was observed in the microstructures after quenching. The quenched bars were cut into

Jan 1, 1942

By Walter Crafts, C. M. Offenhauer

IN the course of study of the heat-treatment of low-alloy steels, the behavior of alloy carbides at subcritical temperatures was found to vary from that indicated by published investigations. In order to establish the ranges of formation of carbides in low-chromium steels, a series of steels containing up to 0.60 per cent carbon and 7.5 per cent chromium has been investigated with respect to the type of carbide formed after quenching and tempering at sub-critical temperatures. The types of carbide formed as products of austenite transformation to pearlitic and pseudomartensitic structures have also been determined. There have been numerous investigations of the carbides in chromium steels and diagrams of the iron-chromium-carbon system.' Westgren, Phragrnén and Ne-gresco2 identified the following carbides in chromium steels: Cementitc............ Fe3C (containing up to about 15 per cent Cr) Trigonal carbide...... Cr7C3 (containing up to about 55 per cent Fe) Cubic carbide........ Cr4C (or Cr23C6) (con- . taining up to about 25 per cent Fe) Orthorhombic carbide , cr3c2 (containing only a few per cent Fe) The most complete information on the iron-chromium-carbon system was supplied by Tofaute, Sponheuer and Bennek3 and by Tofaute, Küttner and Büttinghaus,4 By means of dilatometric and microscopic stzdies, sections of the diagram were established. This diagram showed the presence of the special carbide CI7C3 in steels containing about 2.5 per cent to 12 per cent chromium in low-carbon steels and from about 5 to 20 per cent chromium in I per cent carbon alloys from A1 to room temperature. The present investigation has shown that a carbide inversion from Fe3C to Cr7C3 occurs in chromium steels containing more than about I per cent chromium after hardening and tempering at subcritical temperatures above about 500°C. The type of carbide observed to be more stable in quenched and tempered specimens was also found to be produced by direct austenite transformation in corresponding ranges of temperature and composition. Experimental Procedure The steels used in these experiments were made in magnesia-lined crucibles in high-frequency furnaces and were poured into 2-in. ingots. The ingots were forged into I-in. round bars, and all heat-treatments were conducted on specimens of this section size. Sections of the bar stock 8 in. long were hardened in air, oil or water, depending on the composition, after heating to a temperature sufficiently high to dissolve the carbides. The low-carbon and low-chromium steels were not entirely martensitic after quenching, and contained some ferrite and pseudomartensite. No pearlite was observed in the microstructures after quenching. The quenched bars were cut into

Jan 1, 1942

By P. W. Bakarian

Previous determinationl,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc—also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {IO2}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. Experimental Method Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 1/2 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. I. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler's saw, rounded with a file and polishing paper to a diameter of 0.060 in. and evenly etched in dilute hydrochloric acid to a diameter of 0.038 + 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1942

By C. E Shoenfelt, Gail F. Moulton

Proven and developed oil reserves, and productive capacity increased during 1943 in the fieids of the Rocky Mountain region. Oil production during the year was nearly 45 million barrels, or slightly less than in 1942. The rate of production at the start of 1944 was slightly less than at the start of 1943. Pipe-line projects scheduled for completion during 1944 should permit a substantial increase in the rate of production. Wildcat exploration was more extensive in Montana during 1943 than in other states in the region. The results of wildcat drilling were unsatisfactory, although new oil fields were discovered on the Gebo, Little Buffalo Basin and Steamboat Butte structures of Wyoming, the Gage anticline of Montana, and the Clark Lake structure of Colorado. The area of the structures on which the discovery wells were drilled is known to be considerable, but further drilling is required to determine the importance of these fields. The most important increase in proven reserves resulted from the drilling to newly discovered deeper producing formations in the Elk Basin and other fields of the Big Horn Basin area of northern Wyoming. Lack of a market and unfavorable prices for heavy black oils had prevented complete exploration of favorable areas in the Rocky Mountain region for many years. In particular, the effect on further exploitation of the Big Horn Basin area had been quite serious. The increased demands for all oils created by the war and an increase in price in February 1943, combined later with Government approval of construction of pipe lines from the Big Horn Basin area to the Billings and the Casper districts, provided a basis for undertaking a drilling program. The important additions to reserves were made by drilling in previously discovered fields. The newly discovered fields resulted from drilling on favorable structures which had been known for several years. A continuation of the favorable results obtained during 1943 seems possible only if further testing of the newly discovered fields is satisfactory and if drilling on less favorable known structures or geophysical prospects results in the discovery of new fields. The amount of drilling in the Rocky Mountain states of Colorado, Montana and Wyoming, was about the same during 1943 as .in 1942. However, owing to the fact that a number of wells of large potential production were completed in the Elk Basin field, the total initial production of the prodicing wells was- nearly twice as great for 1943 as for 1942. Explorational activity at the end of 1943 seemed to be directed to geophysical methods, which are required to discover structures hidden beneath the rocks of Tertiary age in the Powder River and other large sedimentary basins. It is in

Jan 1, 1944

By P. W. Bakarian

Previous determinationl,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc—also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {IO2}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. Experimental Method Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 1/2 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. I. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler's saw, rounded with a file and polishing paper to a diameter of 0.060 in. and evenly etched in dilute hydrochloric acid to a diameter of 0.038 + 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1942

By Gail F. Moulton, C. E. Shoenfelt

Proven and developed oil reserves, and productive capacity increased during 1943 in the fieids of the Rocky Mountain region. Oil production during the year was nearly 45 million barrels, or slightly less than in 1942. The rate of production at the start of 1944 was slightly less than at the start of 1943. Pipe-line projects scheduled for completion during 1944 should permit a substantial increase in the rate of production. Wildcat exploration was more extensive in Montana during 1943 than in other states in the region. The results of wildcat drilling were unsatisfactory, although new oil fields were discovered on the Gebo, Little Buffalo Basin and Steamboat Butte structures of Wyoming, the Gage anticline of Montana, and the Clark Lake structure of Colorado. The area of the structures on which the discovery wells were drilled is known to be considerable, but further drilling is required to determine the importance of these fields. The most important increase in proven reserves resulted from the drilling to newly discovered deeper producing formations in the Elk Basin and other fields of the Big Horn Basin area of northern Wyoming. Lack of a market and unfavorable prices for heavy black oils had prevented complete exploration of favorable areas in the Rocky Mountain region for many years. In particular, the effect on further exploitation of the Big Horn Basin area had been quite serious. The increased demands for all oils created by the war and an increase in price in February 1943, combined later with Government approval of construction of pipe lines from the Big Horn Basin area to the Billings and the Casper districts, provided a basis for undertaking a drilling program. The important additions to reserves were made by drilling in previously discovered fields. The newly discovered fields resulted from drilling on favorable structures which had been known for several years. A continuation of the favorable results obtained during 1943 seems possible only if further testing of the newly discovered fields is satisfactory and if drilling on less favorable known structures or geophysical prospects results in the discovery of new fields. The amount of drilling in the Rocky Mountain states of Colorado, Montana and Wyoming, was about the same during 1943 as .in 1942. However, owing to the fact that a number of wells of large potential production were completed in the Elk Basin field, the total initial production of the prodicing wells was- nearly twice as great for 1943 as for 1942. Explorational activity at the end of 1943 seemed to be directed to geophysical methods, which are required to discover structures hidden beneath the rocks of Tertiary age in the Powder River and other large sedimentary basins. It is in

Jan 1, 1944

By Rodney Lawrence, Tim Hackett

INTRODUCTION The western USA contains significant coal reserves in seams 10 feet or more in thickness which lie too deep for surface mining. As part of a demonstration of the use of two legged shield supports in the United States, Kaiser Steel Corporation, under contract to the US government used the longwall method to mine a ten foot thick coal seam in New Mexico. Caliper type shield supports and double drum shearers were used in three longwall panels. During the test, technical, production, and safety data were collected to objectively evaluate the performance of the shields in mining the thick coal seam. This paper presents discussions of practical operating experience and summary statistics to aid the mining industry in planning longwall mines in similar conditions.

Jan 1, 1981

By P. Dayal, L. S. Darken

THE migration of carbon in austenite under the influence of an electric current has been observed qualitatively several times.14 Lebedev and Guterman5 recently have reported quantitative measurements; their method consisted of welding a low-carbon to a high-carbon wire, passing current, and later estimating the carbon distribution metal-lographically. We believe the method reported in this paper is superior in principle since electrolytic migration and ordinary diffusion are not necessarily coupled as in the weld method; also for the first time the extent of migration is determined by combustion analysis for carbon. A uniform tubular specimen (S.A.E. 1045 or 1095) was mounted as illustrated in the figures. the whole assembly being in an atmosphere of purified nitrogen. Direct current (129 to 226 amp at 0.65 to 1.0 v) served as source both of heat and of potential gradient for carbon migration. The duration of experiment was 7.5 to 12 hr, during which time the temperature was controlled (±10°C) manually. The experimental conditions are indicated in the first five columns of table I. With this experimental arrangement, the temperature initially has a maximum value at the central plane. Also, in this vicinity (by virtue of the symmetry), the carbon entering any volume element is equal in quantity to that leaving; the loss or accumulation of carbon occurs near the electrodes since the carbon moves uniformly near the center and is "frozen" at the cold ends. Hence, providing the time of experiment is not sufficiently long to seriously influence the conditions at the central plane, carbon crosses this plane only under the influence of the electrical potential gradient and not under the influence of temperature or concentration gradient. The amount of carbon which has crossed this plane was determined by combustion analysis of the two halves of the specimen. The results of these analyses are shown in the sixth and seventh columns of table I. It will be noted that substantial amounts of carbon migrated from the anode portion to the cathode portion (except at 920°C, which temperature was too low to exhibit the effect in the allotted time). In spite of precau-tions taken, considerable decarburization occurred as may be seen by comparing cols. 8 and 5. In three cases (indicated by asterisks in table I) the specimen was ground on one side, polished, and examined metallographically before analysis. One specimen was normalized and re-examined. Micrographs of selected areas in specimens 4 and 6 are shown in figs. 1 and 2, respectively. Evidence of carbon migration from the anode toward the cathode is quite apparent. Fig. 2 shows abundant graphite as well as cementite in a region near the cathode. The temperature of this zone is estimated at about 800°C. In fig. 1, particularly in the micrograph on the extreme right (the right side of which is of unaltered carbon content), there is evidence of slight depletion of carbon in the immediate vicinity of the cathode as contrasted to the general increase in carbon of the cathode half of the specimen. Although this may be attributed in part to decarbur-ization, it is believed that it is occasioned also by thermal diffusion—migration (of carbon) from a cool to a hot zone4—a phenomenon superimposed upon the electrical migration. Evidence of carbon migration was visible particu-larly during the course of the high-temperature,

Jan 1, 1951

By P. E. Cavanagh

SINCE the 1930's' the production of iron ore in Canada has increased from zero to about 15 million tons per year. In the same short period of about 25 years, the steel industry has doubled in output, while the consumption of steel has also doubled. In the 1930's all Canadian steel was made from imported iron ore, whereas today, Canada is exporting considerably more iron ore than she imports. It appears certain that the production of iron ore in Canada will at least double in the near future, and should be over 45 million tons per year at the end of the next 25 years, in 1980. It also appears certain that most of this iron ore will be exported to the United States, with some proportion going to Europe. In this situation, it is logical and proper at the present time for Canadians to consider means of converting some of all of this Canadian iron ore into semi-finished or finished products in Canada.

Jan 6, 1958