Search Documents

By R. Maddin, N. Ujiiye

ALTHOUGH the cold-rolled texture for body-centered-cubic metals and alloys is well known (see, e.g., Barrett'), the pole figure representing the texture may be interpreted in two ways. It may be regarded as consisting of several ideal preferred orientations with an associated spread (a view which is shared among several investigators2), or it may be regarded as consisting of two sets of continuous preferred orientation also with an associated spread."." Recently, Chen and Maddin7 noted a stable (001) [loo] end orientation for molybdenum single crystals rolled at low rates of reduction provided the initial rolling. orientation" was close to the cube ori-

Jan 1, 1957

By G. Kinder, R. Gilges, W. Stoker, R. Davey

The Bingham Canyon Mine, located 48 km (30 mi) southwest of Salt Lake City, Utah, is operated by Kennecott Copper Corporation's Utah Copper Division. This operation is the world's largest open-pit copper mine and produces 96 000 tons (106,000 st) ore and 327 000 tons (360,000 st) waste each day. This material is loaded by large electric shovels and transported by both truck and rail haulage. To meet the requirements of the Clean Air Act of 1970 (as amended), new facilities for the control of smelter emissions were required and are now nearing the final stages of construction. The facility will be capable of treating all the output from the mine, some 2,530 tons (2,789 st) per day of combined concentrate and precipitate. Costing $280 million and necessitating the replacement of reverberatory furnaces with continuous smelting vessels, the plant, with its massive and complex gas handling and acid-making facility, is required to remain on-stream with the minimum of pollution control equipment outages to conform with Federal Regulation 52.2325. As part of this giant effort, the smelter planning team and supervisory staff considered that new, well organized, highly flexible, readily available maintenance information was essential to assist the maintenance personnel in the performance of their duties.

Jan 1, 1979

By C. H. Chou, A. Sauveur

The senior author of this paper has expressed the belief that when gamma iron transforms into alpha iron on reaching the A3 point, each gamma grain does not change bodily into one or more alpha grains but that the alpha phase forms first at the boundaries and along the crystallo-graphic planes of the austenite grains.1 To quote: On cooling through the point As, at about 900° C, iron passes from the gamma condition to a new allotropic form generally designated as alpha. This transformation, however, is not instantaneous. There are good reasons for believing that it begins at the grain boundaries and along the octahedral planes of the crystals and that it progresses until each grain of gamma iron is changed into a grain of alpha iron, the resulting structure being similar to that of gamma iron. Were it possible to retain

Jan 1, 1929

By Pétroleur Maatschappiju, N. V. de Bataafsche

Jan 1, 1939

[ ]

Jan 1, 1942

[ ]

Jan 1, 1942

Jan 1, 1938

[ ]

Jan 1, 1942

By Pétroleur Maatschappiju, N. V. de Bataafsche

Jan 1, 1939

[ ]

Jan 1, 1942

By N. A. Hasenack

A full description of tests and test results of potgrate--as well as industrial tests is given. It is concluded that the favorable effects of magnetite ores on the pelletizing-plant results can almost be obtained by replacing the magnetites by hematites with coke breeze. The amount of coke breeze to be added should be about 30% above the theoretical value which is derived from the transition heat of the magnetite. The total amount of coke breeze should be limited to 1.5%.

Jan 1, 1977

By W. M. McKewan

Jan 1, 1962

By Henry A. Gordon

Under the title " Hysteromorphous" it is proposed to include deposits which have been formed from original deposits by the influences of the surface-region. The term Hysteromorphous—later-formed—has been used by Prof. Posepny, of Vienna, to distinguish secondary from primary deposits and is more comprehensively applicable than the terms or designations hitherto used for the same thing.

Jan 1, 1896

By M. Katzer, R. Klimpel, J. Sewell

The effect of using selective dispersants as wet grinding aids for ores is demonstrated on laboratory scale batch and continuous grinding equipment. A complete characterization of behavior is performed on a given ore to demonstrate correlations involving torque, % solids, net production rate, and slurry weight and volume loading. The relationship between such laboratory data and industrial scale testing results is very consistent.

Jan 1, 1982

By J. A. Rajala, R. W. Smith

The effect of increasing ionic strength, via monovalent and divalent ions, on alkyl sulfate flotation of hematite and quartz war investigated. The effects of collector chain length and pretreatment on this flotation were also studied. Sodium hexadecyl sulfate was shown to be a superior flotation collector to sodium dodecyl sulfate for recovery of hematite when there was no salt addition. Similar observation were made when sodium sulfate or sodium chloride was used to control ionic strength. Sodium dodecyl sulfate floated hematite better than its longer chutited counterpart under conditions of low pretreatment temperature and increasing calcium chloride concentration. The flotation recovery for all salt containing pulps was almost always improved after preboiling. Most of the results obtained when the pretreatment temperature was raised were attributed to increased solubility of the collector.

Jan 1, 1984

By S. Y. Ezz

The quality and extent of fluidization of fine iron ore beds with gases were investigated. Factors affecting the rate of reduction with H, and the sintering of the partially reduced material were studied. Trials to retard sintering by covering the particles' surface with nonsintering materials were successful. THE gaseous reduction of iron ores is a gas-solid reaction. Hence the fluidization technique seems ideally suited to it. However, a serious drawback

Jan 1, 1961

By J. H. Keeler

AN alloy of zirconium containing 18 atomic pct Cb was found to be body-centered-cubic and readily deformable at room temperature. The behavior of this alloy provided an opportunity to determine if

Jan 1, 1957

By Thos Egleston

The sands of Snake River, Idaho, have long been known to contain gold. They were worked by some of the first prospectors who came to Idaho, and on the banks still stand the ruins of camps abandoned for years. There are almost always prospectors searching for gold during the season of low water, and it is not an infrequent thing to find a miner of the old type actually panning the sand, or the prospect-hole which he has just left. There is more or less mystery about these miners and their methods of finding the spots where they work. They are always subjects of much speculation to the ordinary traveller. The rich discoveries are, for the best of reasons, concealed until the claims can be taken up. It is difficult to find a place where there are no prospects, but the " colors " are so very fine that they do not offer much inducement to enterprise. The California miner usually values a color at from 5 to 10 cents, often the latter; while on Snake River it would take 100 colors, or even more, to make that amount.

Jan 1, 1890

I HAVE previously shown you in the Fifth Book the process of making guns and gun carriages, together with other preparations and methods of moving them. If I now failed to show you more about them, it would be as if I had pointed out only the useless shadow of a thing, for I did not show the kinds and arrangement of their supplies or how the effects for which they are made are achieved. For these reasons I now wish to tell you, in addition to what I have already said, how saltpeter is made and the methods of refining it well; what it is and how without it guns and many effects of violent and artificial fires would have been discovered in vain. After this, I also wish to tell you the methods of compounding the powders for large and small guns, and finally how these are loaded and discharged. I also wish to tell you how mines are made, and fire tubes, [149v] fire pots, squibs, fireballs, rockets, shells, grapeshot, and other similar devices for shooting fire in order to bum ships, supplies, bridges, and ramparts, or, in offense, for firing on batteries. I also wish to teach you to make certain bronze balls for shooting, which carry fire and break in many pieces when they hit. For surely, besides being terrifying to the sight, they would be harmful to armies lined up in battle when they are fighting. Likewise, I wish, to enlighten you as to how artificial fires are made that last long and are difficult to extinguish. Since these are fine and useful things in wars, every captain and soldier should give them consideration and know how to use them when necessary. You will be pleased to have this information if for no other reason than that you can teach it to those who take delight in celebrating holidays with festivities and with fires.

Jan 1, 1942

By James Douglas

American metallurgical inventions have not always been absolute metallurgical improvements, if accurate work be the standard of comparison; but when we review the new methods and machinery which have been generally accepted, we find that some have become essential to the metallurgist the world over, while all are so admirably adapted to the peculiar requirements of our local conditions that they have entirely supplanted foreign processes and appliances. The necessity of diminishing to the utmost the employment of labor (owing to its great cost), and the inexorable requirements of our modern joint-stock corporate system, which demands that large quantities be worked up in order to secure large returns, regardless betimes of waste, have been the impelling motives to invention, and indicate the special directions in which originality has been exercised. As might be anticipated, the West has been the most fertile field of inventions by miners and metallurgists, by reason of its great and varied mineral wealth, locked up in ores sometimes lean and often of intricate composition, which must be profitably handled, at a great distance from fuel and from building-materials, by workmen who are paid wages very much higher than those received by their fellow-workmen of like craft in Europe, and in some localities twice as high as those paid for like services even in the eastern States. Moreover, paradoxical as it may seem, the technical inexperience of many of those engaged in mining and metallurgy has helped rather than hindered the progress of invention; fop while there may have been ignorance, there has been radical freedom from

Jan 1, 1894