Search Documents

By S.S. Clarke

The sheet-ground deposits of the Tri-State district, because they are fairly uniform in thickness (7 to II ft.)—rather flat, with an easy dip to the west—and cover a large acreage, offered a problem of improved transportation. Heading advance in this kind of mine is very rapid and track haulage requires a larger crew of trackmen than do other mines, and a heavy investment in track. The use of some type of rubber-tired truck equipment for underground haulage was under consideration for some time by the Eagle-Picher Mining and Smelting Co. The nature of some ore bodies made them not adaptable to truck haulage and some mines that did offer possibilities were equipped with other types of haulage, and the expected savings by the use of trucks did not offset the loss of investment that would be incurred in discarding other equipment. The decision was made to sink a new shaft, designed for skip hoisting, on the Blue Goose ore body, and then develop truck equipment. Developing Tractors and Trailers A study was made of internal-combustion engines for power units in the tractors, but the extreme difficulty of controlling air circulation, and the heavy cost of drilling large churn drill holes for blower installations, led to the adoption of a tractor with a storage battery. The storage-battery tractor that was on the market for mine haulage was impossible to obtain because all were needed for defense work. Several standard electric-truck chassis were purchased and rebuilt in the Eagle-Picher shops. The steering wheel was shortened and set vertical, permitting the driver's seat to be moved forward, and the frame was shortened enough to take the battery box and the fifth wheel support that carried the gooseneck of the dump trailer. The fifth wheel, or turntable, is of the ball and socket type. Tig. I shows the ball fastened to the gooseneck. The socket is split to permit introduction of the ball and is held by through-bolts, and the socket is welded to a ½-in. plate, which in turn is attached to the tractor frame. Smaller wheels and tires were put on to reduce over-all height. If it had been necessary, the spring: could have been reversed, or taken off entirely, to gain additional clearance. The tractors are equipped with 48-cell, 23-plate, 400-A.H. batteries. With the initial tonnage and mileage, the batteries were about 50 per cent down at the end of a shift. Tractors have truck tires 7.50 by 20, 8-ply, front and rear, the rear being dud. After four months of use, the .tires are beginning to show signs of failure.* In

Jan 1, 1943

By C. S. Matthews, H. C. Lefkovits

The performance of depletion-type reservoirs at the stage in which the gas is at such low pressure that gravity is essentially the sole driving force has been investigated both theoretically and by use of scaled models. A simple theory is developed which completely explains the scaled model experiments. It also agrees with some field data. When the range of production rates to be considered is less than 25, the theory predicts that the production rate decline curve for homogeneous reservoirs in which there is a free surface will be of the hyperbolic type with n = 2: The theory gives a physical significance to the parameter y. INTRODUCTION This investigation was undertaken to determine a method for prediction of performance of reservoirs where gravity is the sole driving agent. Depletion-type reservoirs fall into this category after the pressure has fallen to some low value. Some examples of this type are found at Healdton ('Oklahoma), Oklahoma City (Oklahoma), Midway-Sunset (California), and East Coalinga (California). Generally the production rate per unit thickness is quite low in such reservoirs, with the conse- quence that this stage is sometimes called the stripper stage. However, per well production rates may be of the order of 50 B/D because of the considerable sand thickness open in some of the reservoirs. In the past, predictions of behavior of such reservoirs have been based on empirical extrapolation of the rate of production to the economic limit. Difficulties arise when new wells are drilled in the field or when production is artificially curtailed, since in such cases the decline rate of individual wells or leases changes and no clear trend can be detected. It was hoped that the present study would lead to improved methods for evaluation of such reservoirs. The study was initiated by building a scaled model for a particular field and by running a number of experiments on this model. Later a simple theory was developed which explained the laboratory results completely. The theory led, as shown below, to a hyperbolic-type decline equation which had been used previously' in a completely empirical manner. THEORY The General Case The problem to be treated here is the following: We are given a homogeneous cylindrical porous reservoir with exterior radius r, wellbore radius r., and height h,, containing, from the bottom up to a height hit oil, some gas, and interstitial water (see Fig. 1 A). The portion of the reservoir between K, and h, is filled with gas at low pressure, with residual oil, and with interstitial water. If at a time t = 0, the level of the oil in the wellbore is lowered to a height h,, what is the production rate from the reservoir at a time to The configuration within the reservoir at some instant

Jan 1, 1957

By S. S. Clarke

The sheet-ground deposits of the Tri-State district, because they are fairly uniform in thickness (7 to II ft.)—rather flat, with an easy dip to the west—and cover a large acreage, offered a problem of improved transportation. Heading advance in this kind of mine is very rapid and track haulage requires a larger crew of trackmen than do other mines, and a heavy investment in track. The use of some type of rubber-tired truck equipment for underground haulage was under consideration for some time by the Eagle-Picher Mining and Smelting Co. The nature of some ore bodies made them not adaptable to truck haulage and some mines that did offer possibilities were equipped with other types of haulage, and the expected savings by the use of trucks did not offset the loss of investment that would be incurred in discarding other equipment. The decision was made to sink a new shaft, designed for skip hoisting, on the Blue Goose ore body, and then develop truck equipment. Developing Tractors and Trailers A study was made of internal-combustion engines for power units in the tractors, but the extreme difficulty of controlling air circulation, and the heavy cost of drilling large churn drill holes for blower installations, led to the adoption of a tractor with a storage battery. The storage-battery tractor that was on the market for mine haulage was impossible to obtain because all were needed for defense work. Several standard electric-truck chassis were purchased and rebuilt in the Eagle-Picher shops. The steering wheel was shortened and set vertical, permitting the driver's seat to be moved forward, and the frame was shortened enough to take the battery box and the fifth wheel support that carried the gooseneck of the dump trailer. The fifth wheel, or turntable, is of the ball and socket type. Tig. I shows the ball fastened to the gooseneck. The socket is split to permit introduction of the ball and is held by through-bolts, and the socket is welded to a ½-in. plate, which in turn is attached to the tractor frame. Smaller wheels and tires were put on to reduce over-all height. If it had been necessary, the spring: could have been reversed, or taken off entirely, to gain additional clearance. The tractors are equipped with 48-cell, 23-plate, 400-A.H. batteries. With the initial tonnage and mileage, the batteries were about 50 per cent down at the end of a shift. Tractors have truck tires 7.50 by 20, 8-ply, front and rear, the rear being dud. After four months of use, the .tires are beginning to show signs of failure.* In

Jan 1, 1943

By G. N. Panagiotou

SIMPTOL, a computer simulation program written in FORTRAN IV for use with Cyber 171/8 System at the National Technical University of Athens, describes the mining operations in an opencast lignite mine operating Bucket Wheel Excavators, Conveyors and Stackers. The central objective of the program is to aid management in the selection of a BWE-Conveyor-Stacker System for a given lignite deposit and equipment layout. Much information can be gained from the program with proper manipulation of the input data, which refer to mining profile, soil characteristics, equipment specifications and availabilities and time study data. The other objective of the program is to aid production scheduling in terms of forecasting production rates of the system. The program has been applied to Kardia lignite mine to evaluate its usefulness to represent the actual situation of the system being simulated.

Jan 1, 1983

By Gilbert Thiessen

THE purposes of this paper are (1) to show that the mineral matter content of coal is satisfactorily represented by the Parr formula; that is, Mineral matter = 1.08 Ash + 0.55 Total sulfur (2) to compare ash-to-mineral-matter ratios with factors by which ash values must be multiplied in order that dry, factor-times-ash-free values shall equal Parr unit coal values; (3) to examine such ash-correction factors and to compare them with similar factors corresponding to certain simplifications or modifications of the Parr formulas and (4) to show that ash-correction factors used for simplification in calculating approximate unit coal calorific values cannot be. correctly used for the conversion of other determined values in an analysis to the unit coal basis, but that each type of calculation requires separate treatment in simplification.

Jan 1, 1934

By Jacob Lychenheim

IN connection with the manufacture of special Beseemer pig, containing .030 per Cent. or less of phosphorus, it was found that the phosphorus in anthracite varied so greatly that it was necessary to sample and analyze each car-load. This, of course, in addition to our routine work, involved a considerable amount of extra trouble, and some experiments were made, with the view of cutting down the time and labor of the determination to a minimum.

Jan 1, 1895

By A. R. Kinkel

The Shasta copper-zinc district of northern California lies in the foothills of the Klamath Mountains at the northern end of the Sacramento Valley. It contains two main areas of base-metal ore deposits, the East Shasta and West Shasta districts shown in Fig. 1. The East Shasta includes the area from the Afterthought mine, near the settlement of Ingot on U. S. highway 299 East, to the Bully Hill mine, on the north side of the Pit River, 9 miles to the north- west. The West Shasta, a well-defined northeast- trending district about 8 miles long and 2 miles wide, west of the Sacramento River, Fig. 2, is the western part of the ore-bearing area formerly known as the Shasta copper belt. Referred to in the older writings as a copper arc, this belt was thought to form a crescent extending entirely around the head of the Sacramento Valley, the convex side to the north. Recent studies by the U. S. Geological Survey in cooperation with the California State Division of Mines show that there are two districts, one at each end of the so-called copper arc, which are distinct in geologic structure and ore occurrences, and that there is only sporadic and unconnected copper mineralization between them.

Jan 2, 1955

By E. S. Leaver

THE purpose of this paper is to describe, in a general way, gold-dredg-ing operations in California, with particular reference to unusual features, including types of deposits and recent attempts to improve the recovery of the gold. DREDGING AREAS The gold-bearing formations that traversed the western slope of the Sierra Nevadas for a north and south distance of some 300 miles furnished the immediate source of the gold found in most of the placer deposits of California.. Erosion through a long period carried the gold, together with various forms of partly disintegrated material, to lower elevations and formed placer deposits. Through the classifying action of water in motion, the coarser gold and heavier material of various kinds were deposited relatively near the source; consequently, in' the higher moun-tain country, old river channels were worked feverishly during the early California gold-rush days because of their high gold content. With the working out of these known high-grade channels, and from the knowledge thus obtained of prehistoric stream beds, drift mining was started and flourished until about 1890. Even today many drift mines are operating with the objective of opening other old Tertiary river channels that have been covered by volcanic flows.

Jan 1, 1937

By J. A. Woolf, E. S. Leaver

THE purpose of this paper is to describe, in a general way, gold-dredging operations in California, with particular reference to unusual features, including types of deposits and recent attempts to improve the recovery of the gold. Dredging Areas The gold-bearing formations that traversed the western slope of the Sierra Nevadas for a north and south distance of some 300 miles furnished the immediate source of the gold found in most of the placer deposits of California. Erosion through a long period carried the gold, together with various forms of partly disintegrated material, to lower elevations and formed placer deposits. Through the classifying action of water in motion, the coarser gold and heavier material of various kinds were - deposited relatively near the source; consequently, in the higher mountain country, old river channels were worked feverishly during the early California gold-rush days because of their high gold content. With the working out of these known high-grade channels, and from the knowledge thus obtained of prehistoric stream beds, drift mining was started and flourished until about 1890. Even today many drift mines are operating with the objective of opening other old Tertiary river channels that have been covered by volcanic flows. Adjacent to these areas, which contained relatively high gold values in the older river channels, smaller particles of gold, gravel, and debris were deposited along the sides of the former stream beds and on the adjoining flat areas, thus forming the large placer deposits, which were worked principally by hydraulic mining. Following the course of the ancient rivers and of the present drainage system to the lower edge of the foothill country, extensive areas of alluvial

Jan 1, 1937

By Tom Westgarth

As papers are placed before you upon large gas-engines in Belgium and Germany, it was considered that some information should be given upon the same subject in Great Britain. I therefore agreed to compile these notes, which I have made very short in view of the somewhat full nature of the other papers presented to this meeting, and considering the complete nature of the many publications which have been made recently upon the subject of large gas-engines. I give below Tables I. to VI., showing the number and particulars of large gas-engines which have been built or are building by British makers, and in view of the growing size of gas-engines I have concluded that engines of less than 500 h.p. cannot now he included in the category of large gas-engines, and therefore I have not considered engines under that power. Table I.—-" Oechelhauser " Type Gas-Engines. Built or Building by William Beardmore Co., Limited, Glasgow Indicated ! Engines. Horse-Power Type. Nature of Work. Gas Used. 6 2,500 Twin cylinder. Dynamo. Producer. 1 in Single cylinder. Rolling-mill. Producer. 4 1,250 Twin cylinder. Dynamo. Producer. 2 1,250 Single cylinder. Dynamo. Producer. 4 625 Single cylinder. Dynamo. Producer. 1 625 Single cylinder. Rolling-mill. Producer. 1 625 Single cylinder. Air compressor. Producer. 2 500 Single cylinder. Air compressor. Producer. 7 500 Single cylinder. Cement-mill driving Producer. Total, 28 engines ; 32,600 indicated horse-power. * Presented at the Joint Meeting of the Iron and Steel Institute and the American Institute of Mining Engineers, London, July, 1906, and here published under a mutual agreement between the Councils of the two Institutes.

Jan 1, 1907

By Donald Warren, J. F. Libsch

HIS investigation originated as a result of a pre-vious experimental study' of the magnetic properties of Fe-Co alloys fabricated by the powder metallurgy technique. Densities of powder compacts prepared for the magnetics investigation varied from 7.45 to 7.70 g per cu cm or from 93 to 95 pct of the experimental value of 8.08 g per cu cm for a fused alloy of the same composition.' While this range of density is considered sufficiently high for most applications, the highest possible density is to be desired for maximum magnetic properties. By applying a technique similar to the one described above to a pure electrolytic iron powder, Rostoker³ was able to achieve a density of 7.895 g per cu cm, which is the highest density ever reported for sintered iron. While Rostoker's work involved the sintering of an elemental powder rather than a mixture, it was believed that higher densities should also have been obtained for alloys using the above technique because of the recoining operation and the high sintering temperature. Consequently, it was decided to investigate the various factors affecting the density of this alloy with the idea that such a study might lead to higher densities and, as a result, powder alloys having magnetic properties identical with those of the fused alloys. It was believed that the principal reason that near-theoretical densities for the powdered alloy were not obtained was the interference of gases with the normal sintering mechanism. When present during the sintering operation, gases can exert several harmful effects: they can remain on the particle surface and interfere with surface diffusion and plastic flow; they can be released and, under certain conditions, expand the void spaces through gas pressure; or they can remain trapped in the pores and exert a hydrostatic pressure that retards elimination of the pores. Jones,4 Rhines,5 Goetzel," and others have given the effect of gases in the sintering of powder compacts an extensive treatment. Among the more important sources of gases in the sintering process are dissolved gases, adsorbed gases, air entrapped during pressing, and gaseous products of chemical reactions. During sintering adsorbed gases are partly released at a relatively low temperature, while those gases entrapped during pressing cannot escape until their pressure is increased sufficiently through increasing temperature to expand the interpartjcle openings. The remaining adsorbed gases, gaseous reduction products, and dissolved gases produce a similar effect at the higher temperatures. If, in the sintering process, gas evolution occurs after the interpore channels have been sealed, an exaggerated expansion of the void spaces results. This is particularly true if the temperature is high enough for extensive plastic flow. In his fabrication of powder bars from tantalum, Balke7 had to consider the effect of adsorbed hydrogen and provide for its escape during sintering by limiting the compacting pressure to a maximum of 50 tons per sq in. The effect of gases entrapped during pressing was first noted by Trzebiatowski8 when he found that gold and silver powders decrease in density with increasing sintering temperature if pressed at 200 tsi, while they exhibit the usual increase when pressed at 40 tsi. Recent investigators9-11 have also noted that entrapped gases have an effect on the expansion of copper compacts during sintering. Proper provision for the escape of gaseous products of reduction must be made in order to avoid deleterious effects. Myers" states that in the sintering of electrolytic tantalum powder, the temperature was gradually raised to 2600°F with a pause at 2000°F to permit reduction of the oxides. Experimental Details For the present study, 50 pct Co-50 pct Fe compacts in the form of circular disks 1½ in. in diam and 0.15 in. thick were fabricated by the pressing and sintering of a mixture of the elemental powders. It was decided to follow the sintering process by means of liquid permeability measurements, because it was thought that such measurements might serve as a measure of relative pore sizes, as well as a possible indication of the point at which most of the interpore channels become sealed. However, since the permeability as measured by the flow of a liquid, such as ethylene glycol, does not give an absolute indication of the point where the pores have become isolated, a method for determining the percentage of pores connected to the surface was set up. As an additional cross check on the permeability measurements, metallographic methods were used to study the relative pore size. Finally, the property of ultimate interest, the density, was measured. Raw Materials: The powders used consisted of an annealed, 99.9 pct pure, —150 mesh grade of electrolytic iron powder, and a 98 pct pure, —200 mesh grade of reduced and comminuted cobalt powder. The cobalt powder was not further processed either by hydrogen reduction or annealing. The screen analyses for the iron and cobalt powders are given in Table I, while the chemical analyses for each type of powder are listed in Table 11. Table 111 gives the hydrogen loss measurements for the powders according to the M.P.A. Standard Method and for a higher temperature as well. Preparation of Compacts: Equal amounts of the elemental powders were mixed by rotation for 1 hr and then pressed into compacts approximately 0.15

Jan 1, 1952

By R. G. Aspden

The cold rolling and annealing textures were studied for 3 pct Si-Fe grains initially (001) [hkl]. A concentration of (001) [loo] primaries were observed only in the annealing textures of crystals initially having [loo] within 8 deg of the rolling direction. Eke annealing textures of the (001) [I101 cold rolling textures were sensitive to the initial orientation of the grains. Single crystal data were used to explain the formation of (001) [loo] in poly-crystalline malerial. CUBE texture formation in 3 pet Si-Fe sheet occurs during the final high temperature anneal. Its formation is dependent on the proper distribution of (001) plane primaries with reference to the rolling direction&apos; and on the growth of these primaries by secondary recrystallization. The selective driving force for these primaries with (001) within 7 deg of rolling plane is derived from the difference in surface energy between the annealing atmosphere and the crystallographic planes exposed at the surface of the sheet.&apos;-= The alignment of [loo] directions of (001) secondaries with the rolling direction is required for optimum magnetic characteristics7 and is dependent on processing.&apos; A high degree of alignment has been observed when the final cold rolled texture has a strong (111) [ll2] type component3 and the normal grain growth texture prior to secondary recrystallization has components with a [loo] parallel to the rolling direction and planes from (001) to (110) parallel to the rolling plane.1,3,8,9 Generally, this (001) component is much weaker than the (110) component. The growth rate of (001) plane primaries to secondaries has been found to be independent of the orientation of the primaries with reference to the rolling direction, i.e., the secondaries have the same degree of alignment of [loo] directions with the rolling direction as the (001) primaries.&apos; Hence, the rolling and annealing textures of individual grains or single crystals are of interest in understanding the development of the (001) [loo] secondary recrystallization texture. (001) components have been observed in the annealing textures of cold rolled grains initially having a [loo] parallel to the rolling direction and an (001) rotated up to 30 deg from the rolling plane. Crystals initially near the (001) [loo] orientation when rolled under the influence of constraints imposed by neighboring grains form deformation bands and ro- tate in both directions toward (001) <110>.10,11 Deformation bands have been reported also for crystals initially with an (001) within 1 deg of the rolling plane and a [loo] within 1 deg of the rolling direction when rolled as a free single crystal.12 These crystals have weak recrystallization textures and contain near an (001) [loo] component.10-12 When near (001) [loo] crystals are rolled as free single crystals no deformation bands form and the crystals rotate by a single rotation toward (001) [110]. Recrystallization after a 70 pct cold reduction yielded near an (001) [loo] component13 and after a 90 pct cold reduction an (001) [I201 component." Crystals initially near (210) [001] had a texture after a reduction of 70 and 84 pct which was similar to the (111) [li2] but rotated 10 to 15 deg in the transverse direction. These crystals recrystallize to (210) [OOl] or (410) [001] and contain an (001) [loo] component.10,13 An (001) component has not been detected in the normal grain growth textures of other single crystals. Crystals initially having orientations between (110) [001] and (111) [ll2] have a cold rolled texture of principally (111) [ll2] .10>16 Other crystals with a [I101 parallel to the cross direction rotate to (111) [112] and/or (001) [110] stable end orientations. Crystals initially having from (001) [110] to (111) [lie] retain this orientation after cold rolling.15 The cold rolled textures having [I101 directions parallel to the rolling direction had components in the annealing textures related to the deformation textures by 25 to 30 deg rotations about common (1 10) poles. Cold rolled textures of the (111) (112) type recrys-tallized to (120) [001] or (110) [00l]. The purpose of the present work was to further the understanding of the alignment of [loo] directions of (001) secondaries with the rolling direction. The cold rolling and annealing textures of grains initially (001) [hkl] were studied. These data were applied to the formation of (001) [loo] by secondary recrystallization. PROCEDURES AND EXPERIMENTAL TECHNIQUES The (001) poles near the sheet normal and rolling direction are given in Fig. 1 for the 10 grains studied. Each of these grains was located in the center of a polycrystalline specimen approximately 25 mm wide and 50 mm long. The lower case lettered grains, a through dl were about 1.2 mm in diam and near the (001) [loo] orientation. Specimens containing these grains were from a commercial 3 pct Si-Fe alloy with the principle orientation of (110) [001] as obtained by impurity inhibition of growth with manganese sulfide inclusions.17,18 Upper case lettered grains, A through F, were about 6 mm in diam and had (001) planes near the rolling plane and [hkl] di-

Jan 1, 1963

By J. T. Norton, N. J. Grant, A. M. Gervais

An investigation of the creep deformation of coarse-grained high-purity aluminum at temperatures approaching the melting point permitted the formulation of a theory of subgrain formation. Subgrain boundaries were found to be formed by two different processes: kinking and polygonization. Polygonization is considered as the main factor in subgrain formation. SINCE "slipless flow" was first discussed in detail by Hanson and Wheeler,&apos; many studies have been undertaken to determine how metals deform at high temperatures. Several types of observations have been reported. Jenkins and Mellor,² working on the creep of mild steels and various grades of commercial irons, found metallographic evidence of a kind of substructure within the grains after deformation at high temperatures. Homes" observed after creep deformation of steel at high temperatures that the original X-ray spots were sharply divided into several small ones. The same phenomenon was reported by Hirst4 from his studies on lead and later by Crussard5 from his work on aluminum. The works of these investigators demonstrated beyond any doubt that the splitting of the X-ray spots was due to the fact that the grains underwent a division into subgrains during deformation at high temperatures. Since then, numerous experiments have been undertaken on aluminum in order to determine the mechanism of formation of subgrains. Research workers can be divided, for the purpose of discussion, into two different groups as regards thinking on subgrain formation. On one hand, based on the work on polygonization by Cahn,6 Guinier and Lacombe,7 Greenough and Smith," Crussard,10,11 and Servi, Norton, and Grant," it was concluded that subgrain formation was a consequence of the simultaneous effects, first, of inhomogeneous deformation which produced bending of the lattice, and second, polygonization. On the other hand, Wood and coworkers13-16 based their work on the results of an earlier report" which dealt with crystallite size and a fragmentation theory. It is interesting to note that while Greenough and Smith8 and Wood et al. performed similar experiments, their conclusions were quite different. Wood et al. did not recognize polygonization as a fundamental mechanism and said that aluminum, at the beginning of the deformation, fragmented immedi- ately into subgrains in order to permit deformation of the metal, the number of these subgrains being a function of strain rate and temperature. They concluded that deformation of grains occurred by flow along the subgrain boundaries. In view of the contradictory conclusions, it would appear that the data were not explicit enough to provide an unambiguous conclusion. It appears that the techniques by which most of the results were obtained, namely, X-ray work, were not enough by themselves to solve the problem. Another approach was needed. In the present research, therefore, an extensive metallographic study was planned to supplement the X-ray work. The importance of revealing the subgrain boundaries metallographically was realized, and this will explain the extensive development and use of etching techniques. In order that subgrains would be considerably larger and therefore more readily visible under a microscope, the creep experiments were performed at very high temperatures approaching the melting point of aluminum. Development of Experimental Technique Creep tests were run at constant load on high purity (99.995 pct) aluminum specimens having a very coarse grain size. None of the specimens was run to fracture. The specimens were originally round (diameter, 0.187 in.; gage length, 1 in.) and had parallel flats milled in the gage section to permit

Jan 1, 1954

By Wei-Kao Lu

A general rate equation is derived for gas -solid reactions in metallurgical processes by considering the contributions of chemical reaction at inter-phase boundaries and diffusion through the solid product layer simultaneously. This equation takes care of the whole range continuously from purely diffusion control to purely chemical reaction control. The parabolic law,&apos; McKewan&apos;s equationa derived with the assumption of interface area control and the equation derived by Kawasaki et al. with the assumption of purely diffusion control are found as the limiting cases of the corresponding forms of the general rate equation. Many metallurgical processes involving gas-solid reactions have been extensively studied. The common examples of these processes include the reduction of oxides to metallic products, the roasting of sulfides to oxides or chlorides and the oxidation of metals. Gas-solid reactions consist of at least two kinds of steps; one involves the transport of reactant and product to and from the reaction zone and the other is the chemical reaction taking place at the interphase boundaries. In the limiting cases one or the other of the above mentioned steps will be much slower than the other and is then rate controlling. For example, the oxidation of metals is diffusion controlled and obeys the parabolic law.&apos; On the other hand, if the diffusion rate is much larger than the chemical reaction rate then it will be controlled by the chemical reaction rate. This latter case occurs for the reduction of iron oxides studied by McKewan. If the rate of diffusion and of the chemical reaction have the same order of magnitude, a more detailed analysis is necessary. Thus at the beginning of the reaction when the solid and gaseous reactants are in direct contact, the reaction should be chemical reaction rate controlled as no diffusion process is involved. At the other extreme as the reaction zone moves further into the solid, the diffusion distance becomes greater and the diffusion rate continuously decreases. Eventually, therefore, for a sufficiently large sample the rate must become diffusion controlled. As the transition from one controlling step to the other must be continuous, we cannot describe this transition period by either of the two limiting cases. In this paper the author attempts to derive a general rate equation for gas-solid reaction systems. This is effected by considering the rates of diffusion and chemical reaction simultaneously from the state of pure diffusion control to pure chemical reaction control. I) DERIVATION The system under consideration is made of at least three phases, namely the gaseous one, the solid reactant, and the solid product as shown in Fig. 1. The notations are listed at the end of the paper. The mass transfer process involves the diffusion of reactants and products across the solid product layer. It is reasonable to consider that no chemical reaction will take place in the solid product layer with respect to both gaseous reactant and product. For the characteristics of local equilibrium of the system, the diffusion process is really in a quasi-steady-state. It will be proved in the following paragraphs. Then we can invoke the law of conservation of mass valid for all chemical species passing through the layer. The solid reactant sphere has an initial radius, ro, after a fraction of completeness of the reaction, the unreacted core has a radius ri, where r, is in the solid product region. Let Cg be the activity of gaseous reactant in the

Jan 1, 1963

By F. H. Newell

In 1888 the United States Geological Survey began a systematic examination of the water-resources of the West, comparable in character and scope to the study of the deposits of ores or coal. As experience was acquired, the surveys were extended to the East, until now they embrace representative localities in all parts of the United States. The object to be attained is to note and record the distribution of water-supply, and to learn, as far as practicable, the laws governing its fluctuations.

Jan 1, 1901

By W. F. Boericke

The character of the Wisconsin orebodies must be clearly understood to appreciate the difficulties encountered in sampling and estimating them. Unlike the western vein deposits, they do not lie between regular walls, but form large, often highly irregular bodies, on a single floor in the so-called Galena limestone. The bottom of the ore is nearly always on the clay bed (a flat generally well-defined clay seam a few inches thick) which marks the junction of the base of the Galena lime and the top of the next formation, the Trenton lime. Above the clay bed, the orebodies make the unique pitch and flat formation described by Chamberlin.&apos; Theoretically, we should find two pitches, one on either side of the top crevice, diverging as they go down, with the final flats a considerable distance apart on the clay bed. The area between, known locally as core ground, should thus constitute a single defined orebody, with the richer portions near the pitches and the leaner portion in the center of the core. Practically, we find few examples of this perfect orebody. Almost invariably one pitch is better defined than the other, and often the opposite pitch is marked only by a faint line of fracture showing stronger mineralization than the wall rock, or it may be totally lacking. But with an orebody of any size or richness, at least one strong pitch usually tends to follow an east-west trend, or a quartering course. Late mining developments in the rich New Diggings field indicate that these pitches often assume a horseshoe or crescent shape, the richer ore being in the heart of the crescent and the pitches showing less mineralization as they extend outwards. In the northern end of the field, on the contrary, the pitches maintain generally a consistent direction, and have been mined for thousands of feet from the shaft. The length of the orebody may be several thousand feet, the height varying from 10 to 60 ft. and the width from 60 to 250 ft. In fact, on the core side, there is no definite end to the ore. The mineralization simply gets thinner and thinner, and the limit of working depends on the cost sheet and the profit from the recovery.

Jan 1, 1923

By W. F. Boericke

The character of the Wisconsin orebodies must be clearly understood to appreciate the difficulties encountered in sampling and estimating them. Unlike the western vein deposits, they do not lie between regular walls, but form large, often highly irregular bodies, on a single floor in the so-called Galena limestone. The bottom of the ore is nearly always on the clay bed (a flat generally well-defined clay seam a few inches thick) which marks the junction of the base of the Galena lime and the top of the next formation, the Trenton lime. Above the clay bed, the orebodies make the unique pitch and flat formation described by Chamberlin.&apos; Theoretically, we should find two pitches, one on either side of the top crevice, diverging as they go down, with the final flats a considerable distance apart on the clay bed. The area between, known locally as core ground, should thus constitute a single defined orebody, with the richer portions near the pitches and the leaner portion in the center of the core. Practically, we find few examples of this perfect orebody. Almost invariably one pitch is better defined than the other, and often the opposite pitch is marked only by a faint line of fracture showing stronger mineralization than the wall rock, or it may be totally lacking. But with an orebody of any size or richness, at least one strong pitch usually tends to follow an east-west trend, or a quartering course. Late mining developments in the rich New Diggings field indicate that these pitches often assume a horseshoe or crescent shape, the richer ore being in the heart of the crescent and the pitches showing less mineralization as they extend outwards. In the northern end of the field, on the contrary, the pitches maintain generally a consistent direction, and have been mined for thousands of feet from the shaft. The length of the orebody may be several thousand feet, the height varying from 10 to 60 ft. and the width from 60 to 250 ft. In fact, on the core side, there is no definite end to the ore. The mineralization simply gets thinner and thinner, and the limit of working depends on the cost sheet and the profit from the recovery.

Jan 1, 1923

By J. L. Walter

Tungsten ingots with and without small amounts of aluminum, silicon, and potassium were prepared by conventional powder-metallurgy techniques and hot-rolled to 0.001-in.-thick sheet. The ingots were rolled three different ways: I) initially cross-rolled, then straight-rolled; 2) straight-rolled, and 3) straig-ht-rolled, then cross-rolled. Total reductions were 99.8 pct. Samples of the sheet were annealed, in vacuo, at temperatures from 1200" to 2200°C. Substructures and textures were determined by transmission electron microscopy and X-ray diffraction. The doping agents were found to form particles of mullite (Al,Si,O,,) which, on rolling., appear to form strings of particles aligned parallel to the rolling direction. These strings of purticles are associated with an increase in the recrystal-lizution temperature from 1400°C for undoped sheet ThE addition of small amounts of aluminum, silicon, and potassium to tungsten has a profound effect on the grain structure of drawn and recrystallized wire.&apos;" The grains generally do not occupy the entire cross section of the wire and have lengths many times the wire diameter. The grain boundaries are, in general, nearly parallel to the wire axis and have long &apos;&apos;fingers" projecting one into the other as may be seen in Fig. 1, a longitudinal section of recrystallized doped wire. When unsuitable additions or no additions are made or the wire is not sufficiently reduced during draw- to 2000°C for doped sheet. The particles also limit lateral grain growth while allowing growth parallel to the rolling direction. This results in the formation by primary re crystallization of large highly elongated grains of specific preferred orientation. The undoped sheet recrystallized to small equiaxed gains. The preferred orientations of the large grains were determined from axis density plots to be (113) (691). (0i3) (362), (116) (304) types for the initially cross-rolled then straight rolled material. These orientations are similar to the orientations of the large elongated grains in doped and heavily drawn tungsten wire. The nucleation of the large grains appears to occur by recovery of certain of the polygonized regions of specific orientation, followed by strain-induced boundary migration.

Jan 1, 1968

By W. J. Reagan

MANY factors enter into the manufacture of basic open-hearth steel of high quality. Perhaps the two most important are temperature and the iron oxide content of the metal. If we can control these two factors we can essentially control basic open-hearth practice. SOURCE AND EFFECT OF IRON OXIDE Earlier investigators, especially Herty and his associates, have shown that iron oxide is introduced into the open-hearth furnace in four ways:1 1. - By oxidation of the scrap by furnace gases. 2. By decomposition of the limestone. 3. By oxidation of the iron oxide in the slag by furnace gases. 4. By direct addition of iron ore to the charge. We also know that the speed of operation of an open-hearth furnace depends, for a given charge and given combustion conditions, on the rate at which iron oxide will diffuse from the slag into the metal. The rate of diffusion depends upon a number of variables, such as iron oxide content of the slag, slag viscosity, etc., which also depend upon the amount of iron oxide in the metal, amount of carbon present, temperature, and so forth. For a given carbon and a given temperature, the iron oxide content of the metal is in proportion to the iron oxide content of the slag. This fact can be easily verified by analysis of slag samples taken as described by Herty.2 It is preferable to take these samples just before deoxidation. In killing the steel samples with aluminum it is desirable to use aluminum rod of 99 per cent purity; ordinary commercial aluminum rod with a purity of approximately 92 per cent is not satisfactory. In drilling these samples it is also essential to take the largest amount of drillings possible. This gives more accurate results because it eliminates spotty segregation of Al203.

Jan 1, 1932

By Dorsey Hager, G. W. McPherson

The rapid increase of water troubles in the Mid-Continent oil fields is causing much alarm. Troubles occur at Towanda, Eldorado, Augusta, Cushing, Blackwell, and Healdton, although they had not been acute in the Mid-Continent field until about two years ago, when the unusual conditions in the deeper oil fields were first encountered. California faced the same situation, but, thanks to aggressive measures, has largely overcome the dangers. The following analysis of water trouble may throw some light on the subject and be of assistance in solving the problems involved. Water Troutles Classified The presence of water in large quantities in oil sands has the following results: 1. Diminishes oil production. 2. Diminishes casing-head gasoline production: (a) By curtailing the gas flow. (b) By making the use of vacuum pumps unsuccessful. 3. Increases lifting costs: (a) By making it necessary to pump large quantities of water, which requires a fast motion and long stroke (third hole). (b) By requiring the use of compressors for air lift. (c) By causing break-downs and delays due to the high speed necessary to pump water. (d) By making it necessary to treat "cut" or emulsified oil. Oil production is seriously curtailed by the presence of large quantities of water. Lease records show that wells are shut down 40 to 60 per cent, of the pumping time where serious water trouble occurs. While a small quantity of salt water may cut the paraffine and keep the oil moving, several hundred feet, or a hole full of water, effectually "kills" the oil and gas. The quick return of wells to production, once the water is shut off, shows how wells have been affected. The killing of gas sands

Jan 1, 1920